Operating instructions for washing machinesThe washing machine can only be used by people with reduced physical, sensory or mental capabilities, or lack of experience or ... Unauthorised

Operating instructionsfor washing machines

To avoid the risk of accidents or damage to the machine, it is essentialto read these instructions before it is installed and used for the first time.

en-GB M.-Nr. 10 655 500

Contents

2

Caring for the environment .................................................................................. 6

Warning and Safety instructions ......................................................................... 7

Operating the washing machine ........................................................................ 14Control panel ......................................................................................................... 14Programme duration.............................................................................................. 15Delay start ............................................................................................................. 15Standard display ................................................................................................... 16Examples on how to operate the machine............................................................ 16

Before using for the first time ............................................................................ 17Inserting detergent cartridges ............................................................................... 17Setting the language ............................................................................................. 19Removing the transit bars ..................................................................................... 19Starting the calibration programme....................................................................... 20

TwinDos ................................................................................................................ 21

Washing environmentally and economically .................................................... 22EcoFeedback......................................................................................................... 23

1. Prepare the laundry......................................................................................... 24

2. Select a programme........................................................................................ 25

3. Load the washing machine............................................................................. 26

4. Select programme settings ............................................................................ 27

5. Add detergent .................................................................................................. 29TwinDos................................................................................................................. 29Detergent dispenser drawer .................................................................................. 30CapDosing............................................................................................................. 31

6. Start the programme - the end of a programme .......................................... 33

Spinning................................................................................................................ 34

Delay start ............................................................................................................ 36To select delay start .............................................................................................. 36To change delay start ............................................................................................ 36To cancel delay start and begin the programme straight away ............................ 36

Programme chart ................................................................................................ 37

Contents

3

Options ................................................................................................................. 42ProgrammeManager.............................................................................................. 42

Intensive ........................................................................................................... 42ECO.................................................................................................................. 42Extra gentle ...................................................................................................... 42Extra quiet ........................................................................................................ 42AllergoWash ..................................................................................................... 42

Short...................................................................................................................... 43Water plus ............................................................................................................. 43Stains..................................................................................................................... 43Wash programme chart - ProgrammeManager..................................................... 44

Programme sequence......................................................................................... 46

Garment care label symbols............................................................................... 49

Changing the programme sequence ................................................................ 50Cancelling a programme ....................................................................................... 50Interrupting a programme...................................................................................... 50Changing a programme......................................................................................... 50Adding or removing laundry after the programme has started ............................. 51

Detergent ............................................................................................................. 53The correct detergent............................................................................................ 53Water softeners ..................................................................................................... 53Dispensing aids ..................................................................................................... 53Fabric conditioner and liquid starch...................................................................... 53Miele recommended detergents ........................................................................... 54Recommended detergents in accordance with Directive (EU) Nr. 1015/2010...... 55

Cleaning and care ............................................................................................... 58Cleaning the drum (Hygiene info) .......................................................................... 58External casing and fascia panel........................................................................... 58Cleaning the detergent dispenser drawer ............................................................. 58TwinDos maintenance ........................................................................................... 60

Starting the maintenance programme.............................................................. 60Cleaning the compartments............................................................................. 60

Cleaning the water inlet filter ................................................................................. 61

Contents

4

Problem solving guide ........................................................................................ 62The programme does not start.............................................................................. 62The following fault messages appear in the display and the programme stops... 63A message appears in the display at the end of the programme ......................... 64A message about the TwinDos System has appeared in the display ................... 66Problems with TwinDos ......................................................................................... 67General problems with the washing machine ....................................................... 68An unsatisfactory wash result ............................................................................... 70The door will not open........................................................................................... 71Opening the door in the event of a blocked drain outlet and/or power failure ..... 72

After sales service ............................................................................................... 74Repairs .................................................................................................................. 74Optional accessories............................................................................................. 74Warranty: U.K. ....................................................................................................... 74Warranty: Other countries ..................................................................................... 74

Installation and connection ................................................................................ 75Front view .............................................................................................................. 75Rear view............................................................................................................... 76Installation surface ................................................................................................ 77Transporting the washing machine to its installation site...................................... 77Removing the transit bars ..................................................................................... 77Re-fitting the transit bars....................................................................................... 79Levelling the machine............................................................................................ 80

Screwing out and adjusting the feet................................................................. 80Building under a continuous worktop/ in a kitchen run.................................... 81Washer-dryer stack .......................................................................................... 81

The water protection system................................................................................. 82Connection to the water supply ............................................................................ 84Drainage ................................................................................................................ 86Electrical connection U.K. ..................................................................................... 87

Consumption data ............................................................................................... 88Note for test institutes ........................................................................................... 89

Technical data...................................................................................................... 91Data sheet household washing machines............................................................. 92

Contents

5

Settings ................................................................................................................ 94Language ........................................................................................................... 95TwinDos................................................................................................................. 95Degree of soiling.................................................................................................... 97Buzzer volume....................................................................................................... 97Keypad tone .......................................................................................................... 97Consumption......................................................................................................... 97Code...................................................................................................................... 98Temperature unit.................................................................................................... 98Display brightness................................................................................................. 98Dark display........................................................................................................... 98Machine switch-off................................................................................................ 99Display maximum load .......................................................................................... 99Display programme name ..................................................................................... 99Memory ................................................................................................................. 99Pre-wash Cottons................................................................................................ 100Gentle action ....................................................................................................... 100Reduce temp....................................................................................................... 100Water plus ........................................................................................................... 100Water plus level ................................................................................................... 101Maximum rinse level............................................................................................ 101Suds cooling........................................................................................................ 101Low water pressure ............................................................................................. 102Anti-crease .......................................................................................................... 102

Optional accessories ........................................................................................ 103Detergent............................................................................................................. 103Specialist detergents........................................................................................... 103Fabric care........................................................................................................... 104Additives.............................................................................................................. 104

Caring for the environment

6

Disposal of the packing mater-ialThe packaging is designed to protectthe appliance from damage duringtransportation. The packaging materialsused are selected from materials whichare environmentally friendly for disposaland should be recycled.

Recycling the packaging reduces theuse of raw materials in the manufactur-ing process and also reduces theamount of waste in landfill sites.

Disposing of your old appli-anceElectrical and electronic appliances of-ten contain valuable materials. Theyalso contain specific materials, com-pounds and components, which wereessential for their correct function andsafety. These could be hazardous to hu-man health and to the environment ifdisposed of with your domestic wasteor if handled incorrectly. Please do not,therefore, dispose of your old appliancewith your household waste.

Please dispose of it at your local com-munity waste collection / recyclingcentre for electrical and electronic ap-pliances, or contact your dealer orMiele for advice. You are also respons-ible (by law, depending on country) fordeleting any personal data that may bestored on the appliance being disposedof. Please ensure that your old appli-ance poses no risk to children while be-ing stored prior to disposal.

Warning and Safety instructions

7

This washing machine complies with current safety requirements.Inappropriate use can, however, lead to personal injury and dam-age to property.

To avoid the risk of accidents and damage to the machine, pleaseread these instructions carefully before using it for the first time.They contain important information on its safety, use and mainten-ance.Keep these instructions in a safe place and ensure that new usersare familiar with the content. Pass them on to any future user.

Correct application

This washing machine is intended for use in domestic householdsand similar working and residential environments.

The washing machine is not intended for outdoor use.

It must be used only as a domestic appliance to wash items whichare specified by the manufacturer as being washable on the washcare label. Miele cannot be held liable for damage resulting from in-correct or improper use or operation.

The washing machine can only be used by people with reducedphysical, sensory or mental capabilities, or lack of experience orknowledge, if they are supervised whilst using it or have been shownhow to use it safely and recognise and understand the con-sequences of incorrect operation.


8

Safety with children

Children under 8 years of age must be kept away from the wash-ing machine unless they are constantly supervised.

Children 8 years and older may only use the washing machine un-supervised if they have been shown how to use it safely and recog-nise and understand the consequences of incorrect operation.

Children must not be allowed to clean or maintain the washingmachine unsupervised.

Please supervise children in the vicinity of the washing machineand do not let them play with it.

Technical safety

Please observe the instructions in "Installation and connection"and "Technical data".

Before setting up the washing machine, check it for any externallyvisible damage. Do not install or use a damaged machine.

Before connecting the washing machine, ensure that the connec-tion data on the data plate (fuse rating, voltage and frequency) matchthe mains electricity supply. If in any doubt, consult a qualified elec-trician.

Reliable and safe operation of this washing machine can only beassured if it has been connected to the mains electricity supply.


9

The electrical safety of this washing machine can only be guaran-teed when correctly earthed. It is essential that this standard safety requirement is met. If in anydoubt, please have the wiring system of the building tested by aqualified electrician. Miele cannot be held liable for the consequences of an inadequateearthing system (e.g. electric shock).

Do not connect the washing machine to the mains electricity sup-ply by a multi-socket adapter, extension lead or similar. These do notguarantee the required safety of the machine (fire hazard due to therisk of overheating).

Faulty components must only be replaced by genuine Miele ori-ginal spare parts. Only when these parts are fitted can Miele guaran-tee the safety standards of the machine.

The electrical socket must be easily accessible after installation sothat the machine can be disconnected from the electricity supply ifnecessary.

Unauthorised repairs could result in unforeseen dangers for theuser, for which the manufacturer cannot accept liability. Repairsshould only be undertaken by a Miele authorised service technician,otherwise any subsequent damage will not be covered by the war-ranty.

If the electrical connection cable is faulty it must only be replacedby a Miele authorised service technician to protect the user fromdanger.


10

The machine must be isolated from the electricity supply whencleaning and maintaining the machine and in the event of a fault.

The Miele "Water protection system" protects from water damageprovided the following conditions are met:

– the machine is correctly plumbed in and connected to the electri-city supply.

– if a fault or damage has been identified, the machine must be ex-amined by a competent person before further use, and repaired ifnecessary.

The water flow pressure must be at least 100 kPa and should notexceed 1000 kPa.

In areas which may be subject to infestation by cockroaches orother vermin, pay particular attention to keeping the machine and itssurroundings in a clean condition at all times. Any damage whichmay be caused by cockroaches or other vermin will not be coveredby the warranty.

The machine must not be used in a non-stationary location (e.g.on a ship).

Do not make any alterations to the machine, unless authorised todo so by Miele.


11

Correct use

Do not install the washing machine in a room where there is a riskof frost. Frozen hoses may burst or split. The reliability of the elec-tronic control unit may be impaired at temperatures below freezingpoint.

Before using the machine for the first time, check that the transitbars at the rear of the machine have been removed (see "Installationand connection - Removing the transit bars"). During spinning, atransit bar which is still in place may result in damage to both themachine and adjacent furniture or appliances.

Turn off the stopcock if the machine is to be left for any length oftime (e.g. holiday), especially if there is no floor drain (gully) in the im-mediate vicinity.

Flooding danger. If hooking the drain hose into a wash basin, check that the water candrain off quickly enough to prevent the sink from overflowing. Makesure the drain hose is secure, so that the force of the water flowingout of the hose does not dislodge it.

Take care to ensure that foreign objects (e.g. nails, pins, coins, pa-per clips) do not find their way into the machine with the laundry.These may damage components of the machine (e.g. suds con-tainer, drum), which in turn can result in damage to the laundry.


12

Take care when opening the drum door after using the steamfunction. Danger of burning due to escaping steam and the hightemperature of the surface of the drum as well as the porthole glass.Stand back away from the machine and wait until the steam has dis-sipated.

The maximum load for this washing machine is 9 kg (dry weight).See the "Programme chart" for the maximum recommended loadsfor individual programmes.

If the correct amount of detergent is dispensed, the machineshould not need to be descaled. If, however, you do wish to descaleit, only use a proprietary natural citric acid based descaling agent.Miele recommends using Miele descaling agent which is available toorder online at www.miele-shop.com or from Miele. Strictly observethe instructions on the packaging.

Textiles which have been pre-treated in solvent based cleaningagents must be thoroughly rinsed in clean water before beingwashed in the machine.

Do not use solvent based cleaning agents, e.g. those containingbenzine, in this machine, as this may result in damage to componentparts and create toxic fumes. Such agents also pose a fire and ex-plosion hazard.

Do not use solvent based cleaning agents, e.g. those containingbenzine, to clean the surfaces of the machine. They can cause dam-age to plastic surfaces.

Only use dyes specified by the manufacturer as being suitable foruse in a domestic washing machine. Always observe the manufac-turer's instructions carefully.


13

Colour run and dye removers contain sulphur compounds whichcan cause damage such as corrosion. Do not use these products inthis machine.

If detergent comes into contact with the eyes, rinse them thor-oughly with lukewarm water immediately. If swallowed, seek medicalassistance immediately and retain the packaging or label for refer-ence. Those with skin problems or sensitive skin should avoid theirskin coming into contact with detergent.

Accessories

Accessory parts may only be fitted when expressly approved byMiele. If other parts are used, warranty, performance and product li-ability claims will be invalidated.

A Miele tumble dryer can be stacked on top of a Miele washingmachine using the appropriate stacking kit (available as an optionalaccessory). Please make sure you order the correct one for the Mielewashing machine and Miele tumble dryer.

If installing the machine on a Miele plinth, (available as an optionalaccessory, depending on country), please make sure you order thecorrect one for this washing machine.

Miele cannot be held liable for damage caused by non-compliancewith these Warning and Safety instructions.

Operating the washing machine

14

Control panel

a Display with sensorsSee the next page for more informa-tion.

b Start/Stop buttonFor starting the programme selectedand cancelling a programme once ithas started.

c Temperature buttonFor selecting the temperature.

d Spin speed buttonFor selecting the spin speed.

e Delay start buttonFor selecting delay start.

f Option buttonsVarious options can be added to thewash programme.

g Programme selectorFor selecting the wash programme.

h Optical interface PCFor service technicians.

i buttonFor switching the washing machineon and off.To save energy the washing machinewill switch off automatically 15minutes after the end of the pro-gramme/anti-crease phase or afterbeing switched on if no other selec-tion is made.


15

j sensorScrolls down the list to the next op-tion or decreases a value.

k OK buttonConfirms the programme selected, avalue set or opens a sub-menu.

l sensorScrolls up the list to the next optionor increases a value.

m Dos sensorSwitches on automatic detergentdispensing.

n Cap sensorActivates cap dosing via the deter-gent dispenser drawer.

o EcoFeedback sensorProvides information about the en-ergy and water consumption of theprogramme. Please also refer to"Washing environmentally and eco-nomically - EcoFeedback".

Sensors to light up when the dis-play can be operated via the sensors.

Programme durationAfter the programme has started theprogramme duration will appear in thedisplay in hours and minutes.

If delay start has been selected, theprogramme duration will appear at theend of the delay start time.

Delay startThe delay start time selected will ap-pear in the display.

After the programme has started thedelay start time will begin to countdown.

Once the delay start time has elapsed,the estimated programme duration willappear in the display.


16

Standard displayThe standard display shows the follow-ing from left to right:

2:59 1600

– the programme duration

– the selected wash temperature

– the selected spin speed

Examples on how to operatethe machine

Scrolling through a list

The arrows in the display indicate thata list is available.

Language Touching the sensor scrolls down thelist to the next option and touching the sensor scrolls up the list to the nextoption. The OK sensor is used to activ-ate the option which is currently in thedisplay.

Identifying options selected

Cap

If an option has been activated, this willbe indicated by a tick next to it.

Setting numerical values

Start in h00 :00

A numerical value is highlighted inwhite. Touching the sensor de-creases the value and touching the sensor increases it. The OK sensor isused to activate the value which is cur-rently in the display.

Exiting a sub-menu

Select Back to exit a sub-menu.

Before using for the first time

17

Remove the detergent cart-ridges and the drain hose el-bow from the drumTwo detergent cartridges for automaticdetergent dispensing and an elbowpiece for the drain hose are stored inthe drum.

Reach under the door grip and pullthe door open.

Take the two cartridges and the el-bow piece out of the drum.

Shut the door with a gentle swing.

Inserting detergent cartridgesThe detergent cartridges removed fromthe drum are components of the Miele2-phase system consisting of:

1. UltraPhase 1 (base detergent)

2. UltraPhase 2 (detergent enhancer)

These detergent cartridges are forsingle use only. Replacement deter-gent cartridges are available to orderfrom Miele or via the internet atwww.miele-shop.com (see end of thisbooklet for details). Empty cartridgesshould be disposed of via your localrecycling system.

Remove the caps from the detergentcartridges.


18

Press the TwinDos access panel.

The panel will spring open.

Drop the panel down.

Push the UltraPhase 1 cartridge intocompartment and theUltraPhase 2 cartridge into com-partment , until they lock into pos-ition.

The TwinDos system is now ready foruse.

Remove the protective foil andstickers Remove

– the protective foil from the door.

– any stickers from the front and thelid.

Please do not remove any labels(e.g. the data plate), visible when youopen the door.

This washing machine has undergonea complete functional test at the fact-ory and there will be some residualwater in the drum from this process.


19

Before using the machine for thefirst time ensure that it is correctly in-stalled and connected. See "Installa-tion and connection". Also checkthat the drain filters are securelytightened to prevent the risk of waterleaks during use.

Switch on the washing ma-chine Press the button.

The welcome screen will light up.

Setting the languageYou will be asked to select the languageyou want for the display. It is possibleto change the language at any time via"Settings".

deutsch

Touch the or sensor until thelanguage you want appears in thedisplay.

Confirm your selection of the lan-guage by touching the OK sensor.

Removing the transit barsA reminder to remove the transit barswill appear in the display.

Failure to remove the transit barscan result in damage to the washingmachine and to adjacent cabinetry orappliances.Remove the transit bars as describedin "Installation and connection".

Confirm the removal of the transitbars with the OK sensor.


20

Starting the calibration pro-grammeFor optimum water and energy con-sumption and excellent wash results, itis important to calibrate the washingmachine.

The following message appears in thedisplay:

Open and run Cottons 90°C withoutlaundry

Touch the sensor repeatedly untilyou have read all the rows of text.

The OK sensor will light up.

Confirm the message with theOK sensor.

To do this the Cottons 90 °C must bestarted without laundry and without de-tergent.

No other programmes can be starteduntil calibration has been carried out.

Open the stopcock.

Turn the programme selector to Cot-tons.

1:55 90°C 1600

Press the Start/Stop button.

The calibration programme has started.This will take approx. 2 hours.

At the end of the programme the follow-ing message will be displayed:

Set up complete


Tip: Leave the door slightly open to al-low the drum to dry.

Switch the washing machine off withthe button.

TwinDos

21

The washing machine has an integrateddetergent dispensing unit.

The TwinDos system can be used intwo ways:

1. with the Miele 2 Phase System

or

2. with any other liquid detergent and/orfabric conditioner.

The Miele 2 Phase system

The Miele 2 Phase system uses a basedetergent (UltraPhase 1) and a deter-gent enhancer (UltraPhase 2). In orderto achieve optimum results, the agentsare dispensed separately during thewash process. The 2 Phase systemcleans both white and coloured textilesthoroughly. UltraPhase 1 andUltraPhase 2 single use cartridges areavailable to order from Miele or via theinternet at www.miele-shop.com (seeend of this booklet for contact details).

Liquid detergent/Fabric conditioner

Refillable TwinDos containers are re-quired for liquid detergent and/or fabricconditioner. These are available to orderfrom Miele or via the internet atwww.miele-shop.com (see end of thisbooklet for details).

How TwinDos works

Automatic detergent dispensing for awash cycle is activated via the Dos sensor.

Tip: The washing machine is deliveredpre-set for the Miele 2 Phase system forhardness range II ().

The settings only need to be changed ifyou wish to use a different detergent orif the water hardness is different.See "Settings - TwinDos" for more in-formation.

Automatic dispensing cannot be selec-ted with some programmes, dependingon the detergent present in the TwinDossystem. For example, automatic dis-pensing cannot be activated for theWoollens programme if the Miele 2Phase system is being used. This pre-vents woollen garments being damagedby a detergent which is not suitable forwashing wool.

Washing environmentally and economically

22

Energy and water consumption

– Water consumption and energy us-age are determined by the size of theload. To make the most of your machine,load the maximum dry load for theprogramme you are using.

– When smaller amounts of laundry arewashed, the automatic load recogni-tion system will reduce the amount ofwater and energy used.

– Use the Express 20 programme forsmall, lightly soiled loads.

– Modern detergents make it possibleto wash at lower temperatures (e.g.20 °C). Washing using lower temper-ature settings will save energy.

– To maintain the hygiene of the ma-chine, carry out a hot wash (60 °C orabove) using powder detergent atregular intervals. Hygiene info will ap-pear in the display to remind you tocarry out a hot wash.

Detergent

– For precise dispensing use automaticdetergent dispensing.

– Adjust the dosage to the degree ofsoiling of the laundry.

– Do not exceed the amounts of deter-gent recommended by the manufac-turer on the packaging.

When drying with a tumble dryer

Selecting the highest possible spinspeed for the wash programme willsave energy when drying in a tumbledryer afterwards.

Washing environmentally and economically

23

EcoFeedbackYou can call up information about theenergy and water consumption of yourwashing machine with the EcoFeedbacksensor.

The following information will appear inthe display:

– an estimate of the energy and waterconsumption before the programmebegins.

– the actual energy and water con-sumption during the programme or atthe end of the programme.

1. Estimate

After selecting a programme, touchthe EcoFeedback sensor.

The estimated energy consumptionlevels will be displayed as a bar chart.

Energy

Touch the or sensor to changeto the estimated water consumptionlevels.

Water

The more bars () visible, the higher theenergy or water consumption.

The estimate will vary depending on thewash programme, temperature and anyoptions selected.

The display will change automatically oryou can return to the standard displayby touching the OK sensor.

2. Actual consumption

You can view the actual amount of en-ergy and water used by the programmewhich has just been run both duringand at the end of the programme.

Touch the EcoFeedback sensor.

Energy kWh0.9 Touch the or to switch to the

water consumption display.

The consumption will alter as the pro-gramme progresses.

If the door is opened or the washingmachine has switched off automatic-ally at the end of the programme, thedata will revert to the estimated con-sumption.

Tip: You can view the consumptiondata for the last wash programme inSettings under Consumption.

1. Prepare the laundry

24

Empty all pockets.

Foreign objects (e.g. nails, coins,paper clips, etc.) can cause damageto garments and to components inthe machine.Check the laundry before washingand remove any foreign objects.

Sort the laundry

Sort the laundry by colour and bycare label. Most garments have a tex-tile care label in the collar or sideseam.

Tip: Dark textiles often contain excessdye and should be washed separatelyseveral times before being included in amixed load. Always wash whites andcoloureds separately.

Pre-treat stains

Badly soiled areas, stains etc. shouldbe cleaned as soon as possible,preferably whilst still fresh. Spillagesshould be carefully dabbed off usinga soft, colourfast cloth. Do not rub.

Tip: Badly soiled areas can be pre-treated with liquid detergent, stain re-movers etc. first, following the manu-facturer's instructions. With particularlystubborn stains ask your dry cleaner foradvice.

Solvent-based cleaners (e.g.benzine) can damage plastic parts.When pre-treating garments, makesure that any plastic parts (e.g. but-tons) are protected from cleaningagent.

Chemical (solvent-based) clean-ing agents can cause severe damageto the washing machine.Do not use solvent-based cleaningagents in this machine.

General tips

– Curtains: Remove lead weights firstor place in a laundry bag.

– Underwiring and collar stiffeners: Anyloose wiring in bras, shirt collarstiffeners, etc. should be removed orsewn in.

– Close any zips, attach velcro fasten-ers, fasten hooks and eyes etc. be-fore washing.

– Fasten duvet covers, pillow casesetc. to prevent small items from beingrolled up inside them.

Do not wash any items in this washingmachine which are specified by themanufacturer as not washable on thecare label ( symbol).

2. Select a programme

25

Switch on the washing ma-chine Press the button.

Programme selection

A. Selecting a programme via theprogramme selector:

Turn the programme selector to therequired programme.

The load for the programme selectedwill appear in the display. This will thenbe replaced by the standard display.

B. Selecting a programme using theprogramme selector at the "Furtherprogrammes" position:

Turn the programme selector to Fur-ther programmes.

The following will appear in the display:

Automatic plus Touch the or sensor until the

programme you want appears in thedisplay.

Confirm the programme with the OKsensor.

The maximum load for the relevant pro-gramme will appear in the display. Pre-set programme parameters will be dis-played depending on the programmeselected.

3. Load the washing machine

26

Open the door


Check the drum for pets or foreignobjects before loading it with laun-dry.

The most efficient use of energy andwater is achieved when a full load iswashed. However, do not overload asthis reduces cleaning efficiency andcauses creases.

Unfold the laundry and load looselyinto the drum.

Mixing both large and small itemsgives better wash results and alsohelps distribute the load evenly duringspinning.

Tip: Please note the maximum load forthe different wash programmes. The rel-evant programme load is always shownin the display when you select a pro-gramme.

Close the door

Make sure that no items are caughtbetween the door and the seal.

Shut the door with a gentle swing.

4. Select programme settings

27

Degree of soilingLightly soiled No visible dirt or stains. Possibly slightbody odour.

Normally soiled Visibly dirty and/or just a few slightstains.

Heavily soiled Soiling and/or stains clearly visible.


Degree of soiling

The display will change automatically tothe degree of soiling query:

Normal

Set the degree of soiling with the and sensors and confirm your se-lection with the OK sensor.

The following parameters will changedepending on the degree of soiling se-lected:

– the detergent dosage amount withautomatic detergent dispensing

– with the Heavy degree of soiling set-ting, a pre-wash will be carried outautomatically for some programmes(see "Options").

– the rinse water level will be adjusted

– the programme durations (with lightsoiling the programme duration willbe shorter)

In the Express 20 programme the de-gree of soiling cannot be selected. Ex-press 20 is designed for lightly soiledlaundry.

Tip: You can alter the default setting forthe degree of soiling or switch off thedegree of soiling query in Settings (see"Settings - Degree of soiling").

Select a temperature

You can alter the pre-set temperatureof a wash programme.

Press the Temperature button.


Temperature

Set the temperature you want withthe and sensors and confirmyour selection with the OK sensor.

4. Select programme settings

28

Selecting a spin speed

You can alter the pre-set spin speed ofa wash programme.

Press the Spin speed button.


Spin speed rpm1600

Set the spin speed you want with the and sensors and confirm yourselection with the OK sensor.

Select options

Press the button for the option youwant.

The indicator light in the button willcome on.

Not all options are suitable for usewith every programme. You can onlyselect options which are compatiblewith the programme being used.

See "Options".

Switch on delay start (if re-quired)The start of a programme can bedelayed from 15 minutes up to 24hours, allowing you to make use ofnight-time economy electricity rates, forexample.

See "Delay start".

5. Add detergent

29

There are several options for adding de-tergent.

TwinDosBefore using TwinDos for the first timethe display will show information aboutthe factory default settings for TwinDos.The following will appear in the display:UltraPhase 1+2 set for medium water hard-ness level. Change in "Settings"/ "TwinDos"

Touch the sensor repeatedly untiluntil you have read all the rows oftext.

The OK sensor will light up.

Touch the OK sensor to confirm.

Miele 2 Phase system

UltraPhase 1 and UltraPhase 2 need tobe dispensed in different ratios depend-ing on the colour mix of the laundryload.

Touch the Dos sensor.

For whites Use the and sensors to select

the colour mix of the laundry andconfirm with the OK sensor.

UltraPhase 1 and UltraPhase 2 will bedispensed accordingly.

Liquid detergent/Fabric conditioner

It is possible to use other types of liquiddetergent/fabric conditioner. RefillableTwinDos containers (optional accessor-ies) are required for this.

The washing machine's electronic set-tings need to be adjusted accordingly.See "Settings - TwinDos".


Both agents

Confirm the option displayed with theOK button or select another deter-gent or fabric conditioner with the and sensors.

Tip: The recommended detergent(s) isshown in the display and marked with atick ().

The appropriate amount of detergentand/or fabric conditioner for the pro-gramme will now be dispensed.

Adding stain remover

There are two options for adding stainremover in addition to using the auto-matic dispensing system:

– Use the Booster cap

– Add stain remover to the com-partment.

5. Add detergent

30

Detergent dispenser drawerToo little detergent results in:

– Laundry not getting properly cleanand with time it may become greyand hard to the touch.

– Greasy particles clinging to laundry.

– Limescale deposits on the heater ele-ments.

Too much detergent results in:

– Excessive foam which causes a lowlevel of agitation and poor wash,rinse and spin results.

– High water consumption (an addi-tional rinse cycle will automaticallyswitch in).

– A burden to the environment.

Pull out the detergent dispenserdrawer and add detergent to thecompartments as follows:

Detergent for the pre-wash (divide thetotal recommended amount as follows:add ⅓ to compartment and ⅔ tocompartment )

Detergent for the main wash

/Fabric conditioner, liquid starch or cap-sules.

See "Detergent" for further information.

5. Add detergent

31

CapDosingThree different types of capsule areavailable:

= Fabric care (e.g. fabric condi-tioner, proofing agent)

= Additives (e.g. detergent en-hancers)

= Detergent (for the main washonly)

Each capsule contains the correctamount for one wash cycle.

You can order the capsules online atwww.miele-shop.com or from Miele(see the end of this booklet for contactdetails).

Keep capsules out of the reachof children.

Activating CapDosing Touch the Cap sensor.

The first type of capsule which can beselected for the programme will appearin the display.

Cap

Select the type of capsule you wantwith the and sensors and con-firm your selection with the OKsensor.

Inserting a capsule Open the detergent dispenser drawer.

Open the lid of the / compart-ment.

Press the capsule in firmly.

5. Add detergent

32

Close the lid and press it firmly shut.

Close the detergent dispenserdrawer.

The capsule is opened by the act ofinserting it in the detergent dispenserdrawer. The contents can run out ofthe capsule if you then remove itfrom the drawer before it is used.In this case, dispose of the capsuleand do not re-use it.

The wash programme will dispense thecontents of the capsule at the correcttime.

Water intake to the compartmentis solely via the capsule.No additional fabric conditioner maybe added to the compartmentwhen using a capsule.

Remove the empty capsule at theend of the programme.

For technical reasons a small amountof water will remain in the capsule.

Deactivating/changing Cap-Dosing Touch the Cap sensor and follow

the instructions in the display.

6. Start the programme - the end of a programme

33

Start the programme Touch the flashing Start/Stop sensor.

The door will lock (the will appear inthe display to show this) and the pro-gramme will start.

If a delay start time has been selected,then this will count down in the display.At the end of the delay start time or im-mediately after the programme has star-ted (if no delay start time has been se-lected), the programme duration will ap-pear in the display.

The programme sequence is alsoshown in the display. The washing ma-chine lets you know which section ofthe programme has been reached.

At the end of a programmeThe door is still locked during the anti-crease phase and the following will ap-pear alternately in the display:

Anti-crease/Finish

and

Press Start/Stop

Press the Start/Stop button. This willunlock the door.

Pull open the door.

Remove the laundry.

Items left in the drum could discolourother items in the next wash or be-come discoloured themselves.Check that all items have been re-moved from the drum.

Check the folds in the door seal forany small articles, e.g. buttons, whichmight be lodged there.

Tip: Leave the door slightly open to al-low the drum to dry.

Switch the washing machine off withthe button.

If applicable, remove the used cap-sule from the detergent dispensingdrawer.

Tip: Leave the detergent dispenserdrawer slightly open to allow it to dry.

Spinning

34

Final spin speed

Programme rpm

Cottons 1600

Minimum iron 1200

Delicates 900

Woollens 1200*

Silks 600*

Automatic plus 1400

Down duvets 1200

Outerwear 800

Proofing 1000

Sportswear 1200

Separate rinse / Starch 1600*

Maintenance wash 900

QuickPower wash 1600*

Express 20 1200

Shirts 900

Dark garments / Denim 1200

Drain / Spin 1600

Final spin speed in the pro-grammeWhen a programme is selected the op-timum spin speed for that programmewill appear in the display. For pro-grammes marked with a * in the chart,the optimum spin speed is not the max-imum spin speed.

You can reduce the final spin speed.

However, you cannot select a final spinspeed higher than that shown in thechart.

Rinse and interim spinThere is a spin after the main wash andbetween the rinses. A reduction in thefinal spin speed will also reduce the in-terim spin speed. If a spin speed of lessthan 700 rpm is selected for the Cot-tons programme, an additional rinse isintroduced.

Spinning

35

To omit the final spin (Rinsehold) Use the Spin speed button to select

the setting (Rinse hold). The laun-dry is not spun after the final rinseand remains in the final rinse water.This helps prevent creasing if thelaundry is not going to be removedfrom the drum immediately after theend of the programme.

– To start the final spin:The washing machine will display themaximum spin speed possible. Youcan select a spin speed lower thanthis. Start the final spin by pressingthe Start/Stop button.

– To end the programme:Use the Spin speed button to selectthe 0 rpm setting (Without spin) andpress the Start/Stop button.

The water will drain away.

To omit rinse and interim spinand the final spin Press the Spin speed button.

Select the 0 rpm setting.

After the last rinse, the water will bepumped away and the anti-creasephase will switch in.

In some programmes an additional rinseis introduced with this setting.

Delay start

36

With delay start you can choose whenyou want the programme to start. Youcan delay the start of the programmefrom 15 minutes up to a maximum of 24hours, allowing you to make use ofnight-time economy electricity rates, forexample.

To select delay start Press the Delay start button.


Start in h00 :00

Use the and sensors to enter thehour and confirm your entry with theOK sensor.

The display will change:

Start in h05: 00

Use the and sensors to enter theminutes and confirm your entry withthe OK sensor.

Tip: The values will count upwards anddownwards automatically if you touchthe or sensor continuously.

To begin delay start Press the Start/Stop button to begin

delay start and the wash programme.


Start in h05: 00

When the delay start time has elapsed,the programme will begin and the dis-play will show the programme durationand the programme sequence.

To change delay startYou can change delay start at any time.

Press the Delay start button.

Change the time Touch the OK sensor.

Start in h05 :29

Now enter the time you want.

To cancel delay start and beginthe programme straight away Press the Delay start button.

Change the time Touch the sensor.

Start now Touch the OK sensor. The wash pro-

gramme will start immediately.

Programme chart

37

Cottons cold to 90 °C Max. load 9.0 kg

Use for Cotton, linen or cotton mix fabric, e.g. table linen, towelling, under-wear, T-shirts etc.

Notes The settings 60 °/40 °C differ from / as follows:

– Shorter programme durations

– Longer temperature holding times

– Higher energy consumption

Where particularly high levels of hygiene are required please select atemperature of 60 °C or higher.

Cottons / Max. load 9.0 kg

Use for Normally soiled cotton garments.

Notes – These settings are the most efficient in terms of energy and waterconsumption for washing cottons.

– With the actual wash temperature reached will be lower than60 °C although the wash performance is the same as with thestandard Cottons 60 °C programme.

Note for test institutes:

The test programme conforms to EN 60456 and the energy label to Directive1061/2010.

Minimum iron cold to 60 °C Max. load 4.0 kg

Use for Synthetic, mixed fibre and easy care cotton.

Note Reduce the spin speed for fabric which creases easily.

Programme chart

38

Delicates cold to 60 °C Max. load 3.0 kg

Use for Delicate garments made from synthetic fibre, mixed fibre, rayon andviscose.

Curtains, including net curtains, specified as machine-washable bythe manufacturer.

Notes – Dust in curtains usually makes a programme with pre-wash advis-able. Select the Heavy setting for the degree of soiling so that apre-wash will be carried out.

– Deselect the spin for items which crease easily.

Woollens cold to 40 °C Max. load 2.0 kg

Use for Machine-washable or hand-washable wool or wool blend fabric. Ifthe care label does not specify a temperature, wash using the coldsetting.

Note Reduce the spin speed for items which crease easily.

Silks cold to 30 °C Max. load 1.0 kg

Use for Silks and other handwashable fabric with no wool content.

Note Place tights, bras etc. in a laundry bag.

Automatic plus cold to 40 °C Max. 6.0 kg

Use for Mixed loads of garments suitable for the Cottons and Minimum ironprogrammes.

Note The wash parameters (e.g. water level, wash rhythm and spin speed)are adjusted automatically in this programme to ensure the bestpossible care and wash result for each item.

Programme chart

39

Down duvets cold to 60 °C Max. load 2.5 kg1 down duvet 2.20 m x 2.00 m

Use for Quilts, duvets and pillows with feather or down filling.

Notes – Remove air from the items before washing to prevent an excessivebuild-up of foam. To do this either push the items into a narrowlaundry bag to compress them or tie the items together with awashable strap.

– Observe the instructions on the wash care label.

Outerwear cold to 40 °C Max. load 2.5 kg

Use for Performance outerwear (e.g. jackets and trousers) made from mem-brane fabric such as Gore-Tex®, SYMPATEX®, WINDSTOPPER®etc.

Notes – Zip up or close jackets before washing.

– Do not use fabric conditioner.

– If wished, these garments can also be re-proofed using the Proof-ing programme. Proofing should not be done every time the gar-ment is washed.

Proofing 40 °C Max. load 2.5 kg

Use for Treating microfibre fabric, skiwear and table linen made from mainlysynthetic fibres to provide a water and dirt resistant finish.

Notes – The items should be freshly laundered and spun or dried beforeproofing.

– For best results, the items should be heat-treated afterwards eitherin a tumble dryer or by ironing.

Programme chart

40

Sportswear cold to 60 °C Max. load 3.0 kg

Use for Sportswear such as singlets and leggings as well as microfibre andfleece garments.

Notes – Do not use fabric conditioner.

– Observe the manufacturer's care label.

Separate rinse / Starch Max. load 9.0 kg

Use for – Rinsing handwashed items.

– Starching table cloths, serviettes and workwear.

Notes – Reduce the spin speed for items which crease easily.

– The laundry should be washed but not treated with fabric condi-tioner.

– Items will be rinsed very effectively using two rinse cycles by ac-tivating the Water plus option.

Maintenance wash 75 °C Empty

With frequent washing at low temperatures there is a danger of a build-up ofbacteria in the washing machine.

Cleaning the washing machine will significantly reduce bacteria, mould andbiofilm and prevent the build-up of unpleasant odours.

Notes – Optimum results can be achieved by using Miele machine cleaner.Alternatively, a universal powder detergent can be used.

– Dispense the machine cleaner or universal detergent directly intothe drum.

– Do not load any laundry. The drum must be empty for the main-tenance wash.

Programme chart

41

QuickPower wash 60 °C – 40 °C Max. load 5.0 kg

Use for Normally soiled garments which are also suitable for washing in theCottons programme.

Note – A special saturation process and wash rhythm ensure that thelaundry is cleaned particularly quickly and thoroughly.

Express 20 cold to 40 °C Max. load 3.5 kg

Use for Cotton garments that have hardly been worn or are only very lightlysoiled.

Note The Short option is activated automatically.

Shirts cold to 60 °C Max. load 1.0 kg/2.0 kg

Use for Shirts and blouses made of cotton and mixed fibre.

Notes – Pre-treat soiled cuffs and collars if necessary.

– Wash silk shirts and blouses in the Silks programme.

– If the pre-set Pre-ironing option is switched off, the maximumload capacity is increased to 2.0 kg.

Dark garments / Denim cold to 60 °C Max. load 3.0 kg

Use for Black and dark items made of cotton, mixed fibre or denim.

Notes – Wash inside out.

– Denim often contains excess dye and may run during the first fewwashes. Wash light and dark coloured items separately.

Drain / Spin Max. load 8.0 kg

Notes – Drain only: Select 0 rpm for the spin speed.

– Make sure you select the appropriate spin speed.

Options

42

Options are selected and deselected viathe relevant buttons and the display.

Press the button for the option youwant.

The relevant button will light up.

Not all options are suitable for use withevery programme.

You can only select options which arecompatible with the programme beingused.

ProgrammeManagerThe ProgrammeManager option can beused to customise the washing pro-grammes to suit your requirements.

Intensive

For hard-wearing laundry that is veryheavily soiled. Cleaning efficiency is in-creased through more intense mechan-ical action and the application of moreheat energy.

ECO

This option reduces energy consump-tion whilst maintaining cleaning effi-ciency. This is achieved by increasingthe wash duration and at the same timereducing the wash temperature selec-ted.

Extra gentle

This option decreases mechanical ac-tion in order to reduce creasing.

Extra quiet

This option reduces noise levels duringthe programme. Use this if you want towash during quiet periods (for instancewhen children are sleeping). The ma-chine will activate the "Rinse hold" op-tion and not spin. The programme dura-tion is longer.

AllergoWash

This option should be used where highstandards of hygiene are required. Moreenergy is used to lengthen temperatureholding times and more water is used toincrease rinsing efficiency.

Not all ProgrammeManager optionsare suitable for use with every pro-gramme. Please refer to the "Washprogramme chart - ProgrammeMan-ager" for a list of suitable pro-grammes.

Options

43

Pre-ironing In order to reduce creasing, the laundryundergoes a smoothing process at theend of the programme. Reducing themaximum load by 50% will give a betterresult. Please note the load informationin the display. Small loads give a betterresult.

The garments must be suitable for dry-ing in a tumble dryer and suitablefor ironing .

ShortUse this option for light soiling with novisible staining.

The wash duration is reduced.

Water plusThe water level in the wash and rinsestages is increased and a second rinseis carried out in the "Separate rinse /Starch" programme.

You can select other functions for theWater plus button. These are describedin "Settings".

StainsIn order to clean stained laundry moreeffectively, you can choose between 7different types of stain. The wash pro-gramme will then adapt to the type ofstain selected. You can select one stainper wash cycle.

Options

44

Wash programme chart - ProgrammeManagerProgrammeManager cannot be selected with programmes which are not listed inthe chart below.

Inte

nsiv

e

EC

O

Ext

rage

ntle

Ext

raqu

iet

Alle

rgo-

Was

h

Cottons X X X X X

Minimum iron X X X X X

Delicates X X X X X

Woollens – – – X –

Silks – – – X –

Automatic plus X X X X X

Down duvets X X X – X

Outerwear X X X X X

Proofing – – – X –

Sportswear X X X X X

Separate rinse / Starch – – – X –

Express 20 – – – X –

Shirts X X X X X

Dark garments / Denim X X X X X

X = Can be selected

– = Cannot be selected

Options

45

The following options can be selected in addition to the pro-gramme:None of the options can be selected with programmes which are not listed in thechart below.

Pre

-was

h1)

Pre

-iro

ning

Sho

rt

Wat

er p

lus

Sta

ins

Cottons X X X X X

Minimum iron X X X X X

Delicates X X X X X

Automatic plus X X – – X

Down duvets X – – X –

Outerwear X – X X X

Sportswear X – X X X

Separate rinse / Starch – – – X –

QuickPower wash – X – X –

Express 20 – X X2) – –

Shirts X X2) X X X

Dark garments / Denim X X X X X

X = Can be selected

– = Cannot be selected1) = Activated automatically when the Heavy degree of soiling setting is

selected2) = Can be deselected

Programme sequence

46

Main wash Rinses Spinning

Waterlevel

Washrhythm

Waterlevel

Rinses

Cottons 2-51)2)3)

Minimum iron 2-42)3)

Delicates 2-42)3)

Woollens 2

Silks 2

Automatic plus 2-42)3)

Down duvets 3-43)

Outerwear 3-43)

Proofing – 1

Sportswear 2-33)

Separate rinse / Starch 0-15)

Maintenance wash 3

QuickPower wash 2

Express 20 1

Shirts 3-43)

Dark garments / Denim 3-52)3)

Drain / Spin – – – –

Please see the next page for a description of the symbols.

Programme sequence

47

= Low water level

= Medium water level

= High water level

= Intensive rhythm

= Normal rhythm

= Sensitive rhythm

= Ultra sensitive rhythm

= Handwash rhythm

= Carried out

– = Not carried out

The washing machine has fully elec-tronic controls with automatic load re-cognition. It takes in the right amount ofwater required for the programme de-pending on the amount of laundry andits absorbency rate.

The programme sequences shown inthe chart are based on the standardprogramme with a full load.

The washing machine programme se-quence display shows which stage ofthe programme has been reached.

Special features in the pro-gramme sequenceAnti-crease:At the end of the programme the drumcontinues to turn at intervals for up to30 minutes to help prevent creasing.Exception: There is no anti-creasephase in the Woollens and Silks pro-grammes.The door can be opened at any timeduring the anti-crease phase.1) If a temperature of 60 °C or higher is

selected, or with and tem-peratures, 2 rinses are carried out. If atemperature of less than 60 °C is se-lected, 3 rinses are carried out.

2) An additional rinse is carried out if:

– there is too much foam in the drum

– a spin speed lower than 700 rpm hasbeen selected

3) An additional rinse is carried out if:

– the Water plus option is selected andthe Extra rinse or Water + and Extrarinse setting has been activated forthe Water plus option in Settings.

4) Run-up to spin: A run-up to spin iscarried out before the wash processbegins to deflate down filled items.Subsequent water intake for the mainwash is through compartment .

5) An additional rinse is carried out if:the Water plus option is selected.

Programme sequence

48

Cottons and Minimum ironPowerWash 2.0, the washing techniquedeveloped by Miele, is activated in theCottons programme with small and me-dium-sized loads and in the Minimumiron programme

How it works

Conventional washing techniques washwith more water than the laundry canabsorb. This total volume of waterneeds to be heated.

The PowerWash 2.0 washing techniqueonly uses slightly more water than thelaundry can absorb. The water whichhas not been absorbed by the laundryheats up the drum and the laundry andis sprayed into the laundry over andover again. This reduces the amount ofenergy used.

Activation

The washing machine calculates theload at the beginning of the wash pro-gramme. PowerWash 2.0 is activated ifthe following conditions are present:

– there is a small to medium-sizedlaundry load in the Cottons pro-gramme and in the Minimum ironprogramme.

– the temperature selected must not bemore than 60 °C.

– the final spin speed selected mustnot be lower than 600 rpm.

– CapDosing (, ) ) has not been se-lected for the main wash.

With some options (e.g. Pre-wash,Water plus) PowerWash 2.0 is not ac-tivated.

Special features

– Drenching phaseThe washing machine will spin a fewtimes at the beginning of the pro-gramme. During spinning, the waterdischarged is sprayed back into thelaundry in order to achieve optimummoisture penetration.

The optimum water level is set at theend of the drenching phase. If neces-sary, the washing machine will pumpwater away or take in a little morefresh water.

– Noises during the heating phaseUnusual bubbling noises can occurwhile the laundry and the drum arebeing heated.

– Use of detergentMake sure you add the correctamount of detergent (for smallerloads).For optimum detergent application,use the TwinDos function.

Garment care label symbols

49

Washing

The figure quoted in the bucket is themaximum temperature the garmentcan be washed at. The number ofbars under the symbol indicates thelevel of agitation permitted.

No bar under the symbol:= normal agitation

One bar under the symbol:= reduced agitation

Two bars under the symbol:= much reduced agitation

Hand wash (if no temperature isspecified, use the lowest tem-perature or cold)

Do not wash

Programme selection examples

Programme Garment care labelsymbols

Cottons

Minimum iron

Delicates

Woollens

Silks

Express 20

Automatic plus

Drying

The number of dots indicates the dry-ing temperature

Normal temperature

Low temperature

Do not tumble dry

Ironing

The number of dots indicates the iron-ing temperature

Hot iron (max. sole plate temp.approx. 200 °C)

Medium hot iron (max. soleplate temp. approx. 150 °C)

Cool iron (max. sole plate temp.approx. 110 °C).

Do not steam iron garmentscarrying this symbol as thiscould cause irreversible dam-age.

Do not iron

Professional cleaning

Dry clean only. The letters indic-ate the type of cleaning agent re-quired.

Professional Wet Clean only

Do not dry clean

Bleaching

Any oxidising bleaching agentcan be used

Only use an oxygen basedbleach or a non-chlorine bleach

Do not bleach

Changing the programme sequence

50

Cancelling a programmeYou can cancel a programme at anytime after it has started:



Cancel programme Touch the OK sensor.

The suds will be pumped away. The fol-lowing will appear in the display:

Prog. cancelled

Pull open the door.

Remove the laundry.

If you want to select a different pro-gramme

Close the door.

Select the programme you want.

Add detergent to the detergent dis-penser drawer, if necessary.


The new programme will begin.

Interrupting a programme Switch the washing machine off with

the button.

Switch the washing machine back onwith the button to continue withthe same programme.

Changing a programmeAfter the start of a programme it is nolonger possible to select a different pro-gramme.

Temperature

With the exception of the Cottons pro-gramme, it is possible to select a differ-ent temperature up to 5 minutes afterthe programme has started.

Press the Temperature button.

Use the , and OK sensors tochange the temperature.

Spin speed

It is possible to change the spin speedup until the final spin begins.

Press the Spin speed button.

Use the , and OK sensors tochange the spin speed.

Options

It is possible to select or deselect theShort and Water plus options up to 5minutes after the programme has star-ted.

Tip: It is not possible to make anychanges to the programme or to cancelit if the safety lock has been activated.


51

Adding or removing laundryafter the programme has star-ted Press the Start/Stop button.


Cancel programme Scroll up the list with the or

sensor to:

Add laundry Touch the OK sensor.

If this message does not appear in thedisplay then it is no longer possible toadd or remove items of laundry.

The programme will stop and the doorwill unlock.

Pull open the door.

Add or remove items.

Close the door.


The programme will continue.

Please note:

Once a programme has started thewashing machine cannot recognise anyadjustment to the load.

For this reason, if laundry is added orremoved after the start of a programme,the machine will always complete theprogramme cycle assuming a full load

The door cannot be opened, if:

– the suds temperature is above 55 °C.

– the water is above a certain level.

– the programme has reached the Spinstage.

If you want to open the door when theabove conditions are present you willneed to cancel the programme.

The safety lock will remain activated ifthe temperature in the drum is above55 °C. The lock will not deactivate un-til the temperature has dropped to be-low 55 °C.


52

Safety lock

The safety lock prevents the temperat-ure, spin speed or options beingaltered during a wash programme.

To activate the safety lock



Cancel programme Scroll up the list with the or

sensor to:

Activate lock

Touch the OK sensor.

To deactivate the safety lock

Proceed as for activating the safetylock.


Deactivate lock


The safety lock is now deactivated.

Detergent

53

The correct detergentAll detergents produced for automaticwashing machines are suitable. Followthe manufacturer's instructions anddosage recommendations on the pack-aging.

For users in Asia:please use a low foaming detergentsuitable for use in front-loading ma-chines

The right amount to dispensewill depend on the following:– the soiling level of the load

– the quantity of the laundry

– the water hardness level.Check with your local water supplierif you do not know the hardness levelin your area.

Water softenersA water softener can be used to cutdown on the use of detergents in areaswith water hardness levels II and III.Dispense according to the amount spe-cified on the packaging. First add deter-gent and then the water softener.

You can then use the recommendedamount of detergent for water hardnesslevel I.

Water hardness levels

Hardnessscale

Hardness levelin mmol/l

German scale°d

I (soft) 0 – 1.5 0 – 8.4

II (medium) 1.5 – 2.5 8.4 – 14

III (hard) above 2.5 above 14

Dispensing aidsUse dispensing aids, (e.g. balls) if theseare supplied with the detergent, particu-larly when using liquid detergent.

Refill packs of detergentWhen purchasing detergent buy refillpacks wherever possible. This helps re-duce the amount of waste packaging.

Fabric conditioner and liquidstarchFabric conditioner makes garments soft to handle andhelps prevent static cling when tumbledrying.

Starch stiffens and gives body to items of laun-dry, e.g. shirts, tablecloths and bedlinen.

Detergent

54

Miele recommended detergentsMiele detergents and care products have been specially designed for Miele wash-ing machines. They are available to order via the internet at www.miele-shop.comor from Miele.

MieleUltraPhase 1 / 2

MieleCap

MieleCap

MieleCap

Cottons – Minimum iron – Delicates , , –

Woollens – , – –

Silks – – –

Automatic plus – Down duvets – – –

Outerwear – – –

Proofing – – –

Sportswear – – –

Separate rinse /Starch

–/– –/– /– –/–

QuickPower wash – – –

Express 20 – –

Shirts – Dark garments /Denim

– –

Recommended Sport SilkCare

– Not recommended Down Fabric conditioner

Outdoor Reproofing

WoolCare Booster

Detergent

55

Recommended detergents in accordance with Directive(EU) Nr. 1015/2010The recommendations apply to the temperature ranges given in the Programmechart.

Universal Coloureds Delicates andwoollens

Specialist

detergent

Cottons – –

Minimum iron – – –

Delicates – – –

Woollens – –

Silks – –

Automatic plus – – –

Down duvets – –

Outerwear – –

Sportswear – –

Maintenance wash 2) – –

QuickPower wash – –

Express 20 – 1) – –

Shirts – –

Dark garments / Denim – 1) –

Recommended 1) Liquid detergent

– Not recommended 2) Powder detergent

Detergent

56

Fabric conditioner and liquidstarch at the end of the pro-grammeYou can dispense fabric conditionereither by using automatic dispensing orvia the detergent dispenser compart-ment.

Automatic dispensing

One of the automatic dispensing con-tainers must be filled with fabric condi-tioner.


Activate the appropriate container.

Fabric conditioner will be dispensed inthe last rinse.

Manual dispensing

Add the fabric conditioner or liquidstarch to the compartment or in-sert the appropriate capsule. Do notexceed the maximum level mark.

The agent will be automatically dis-pensed in the last rinse. At the end ofthe programme a small amount of waterwill remain in the compartment.

If starching frequently, thoroughlyclean the dispenser compartment,especially the siphon tube regularly.

Detergent

57

Colour run and dye removers/dyes

Colour run and dye removerscan cause corrosion in the washingmachine.Do not use colour run or dye re-movers in this washing machine.

Dyes suitable for use in domestic wash-ing machines can be used. However,please note that the salt used in thedyeing process can cause corrosion tostainless steel components in the ma-chine if you dye frequently. Always ob-serve the manufacturer's instructionscarefully.

When using the washing ma-chine to dye fabric it is essential toselect the Water plus option.

Adding fabric conditioner or liquidstarch separately

Prepare the starch in accordance withthe manufacturer's instructions on thepackaging.

Tip: When adding fabric conditionerseparately, activate the Water plus op-tion.

Add fabric conditioner to the com-partment or insert the appropriatecapsule.

Add liquid starch to the compart-ment and powder or viscous starch tothe compartment.

Select the Separate rinse / Starchprogramme.

Change the spin speed if necessary.

Activate the Cap sensor if using acapsule.


Cleaning and care

58

Cleaning the drum (Hygiene info)Washing at low temperatures and/or us-ing liquid detergent can cause bacteriaand unpleasant odours to build up inthe washing machine. Use the Mainten-ance wash programme to clean the ma-chine. Run this programme regularly orat the latest when Hygiene info appearsin the display.

External casing and fasciapanel

Disconnect the machine from themains electricity supply before clean-ing or maintenance.

The washing machine must notbe hosed down.

Clean the casing and fascia panelwith a mild non-abrasive cleaningagent or soap and water using a wellwrung-out cloth. Wipe dry with a softcloth.

The drum can be cleaned with a pro-prietary stainless steel cleaningagent, following the manufacturer'sinstructions on the packaging.

Do not use solvents, abrasivecleaners, glass cleaners or multi-pur-pose cleaning agents. These coulddamage plastic surfaces and otherparts.

Cleaning the detergent dis-penser drawer

Washing at low temperatures and theuse of liquid detergent can lead to abuild-up of mould and bacteria in thedetergent dispenser drawer.

Clean the entire drawer at regular in-tervals for hygiene reasons, even ifyou are using the TwinDos system ex-clusively.

Pull out the detergent dispenserdrawer until a resistance is felt. Pressdown the release button and at thesame time pull the drawer right out ofthe machine.

Clean the drawer with hot water.

Cleaning and care

59

Cleaning the siphon tube and thechannel

Liquid starch can cause the siphonto become clogged. Make sure thatyou clean the siphon and siphontube particularly thoroughly after us-ing liquid starch a few times.

Clean the siphon.

1. Remove the siphon from the com-partment and rinse under hot runningwater. Clean the siphon tube at thesame time.

2. Replace the siphon.

Clean the fabric conditioner channelwith a brush and hot water.

Cleaning the detergent dispenserdrawer housing

Use a bottle brush to remove deter-gent residues and limescale from thejets inside the detergent dispenserdrawer housing.

Replace the detergent dispenserdrawer.

Tip: Leave the detergent dispenserdrawer slightly open to allow it to dry.

Cleaning and care

60

TwinDos maintenance

If the system has not been usedfor a long time (more than twomonths) the detergent in the hosescan become viscous.The hoses could become blockedand would then need to be cleanedby a service technician.Clean the TwinDos system

To clean the system you either need a"TwinDosCare" cleaning cartridge oran empty TwinDos container. Both areavailable from the Miele online shop.

The washing machine has a cleaningprogramme for the TwinDos system.Running the cleaning programme willclean the hoses inside the washing ma-chine.

Starting the maintenance programme

Switch on the washing machine andwait until the standard display lightsup.

Touch the and sensors at thesame time until the following appearsin the display:

Language The Settings menu is activated.

Touch the sensor until the follow-ing appears in the display:

TwinDos

Confirm the setting with the OKsensor.

Touch the sensor until the follow-ing appears in the display:

Maintenance Confirm the setting with the OK

sensor.

Compartment Touch the or sensor until the

compartment you want appears inthe display and confirm this with theOK sensor.

Start Mainten.? No Select Yes and confirm this with the

OK sensor. Then follow the instruc-tions that appear in the display.

The hoses will now be cleaned and theTwinDos system can be used again.

Cleaning the compartments

Detergent residue can cause clogging.

Use a damp cloth to clean the com-partment interior when you changethe cartridge or container.

Cleaning and care

61

Cleaning the water inlet filterThe washing machine has a filter to pro-tect the water inlet valve. The access-ible filter in the union at the open end ofthe inlet hose should be checked everysix months or so, or more often if thereare frequent interruptions to the watersupply.

First turn off the stopcock.

Unscrew the inlet hose from the stop-cock.

Remove the rubber seal 1 from therecess.

Using pointed pliers, take hold of theplastic filter bar 2 and remove it.Clean the plastic filter.

Put the filter and seal back in the re-verse order and reconnect the hose.

Turn on the stopcock and check theconnection is watertight. If waterdrips out, tighten the connection.

The filter must be put back in placeafter cleaning.

Problem solving guide

62

Minor faults in the performance of the washing machine, some of which may resultfrom incorrect operation, can be put right without contacting the Service Depart-ment.

The following guide may help you to find the reason for a fault, and to correct it.You should, however, note the following:

Repair work to electrical appliances should only be carried out by a suitablyqualified person in strict accordance with current local and national safety regu-lations. Repairs and other work by unqualified persons could be dangerous. Themanufacturer cannot be held liable for unauthorised work.

Some of the messages in the display are more than one line long. Touch the or sensor to read them in full.

The programme does not start

Problem Cause and remedy

The display remainsdark, and the Start/Stopbutton indicator lightdoes not come on.

There is no power to the machine. Check whether the mains plug is plugged in and

switched on. Check whether the fuse or circuit breaker has

tripped.The washing machine has switched off automaticallyto save energy. Switch it back on with the button.

The display promptsyou to enter a code.

Access via a code has been activated. Enter the code and confirm the entry. Deactivate

the code if you do not wish this message to ap-pear in the display the next time the machine isswitched on.

The following appearsin the display: Service Door lock

The door is not closed properly. The door lock couldnot engage. Close the door again. Start the programme again.

If the fault message appears again, contact theService Department.


63

The following fault messages appear in the display and theprogramme stops

Message Cause and remedy

Water intake See

The water inlet is blocked or restricted. Check whether the stopcock is opened properly. Check whether the inlet hose is kinked. Check whether the water pressure is too low.

The filter in the water inlet is blocked. Clean the filter.

Drainage See The water outlet is blocked or restricted.The drain hose has been fixed too high. Clean the drain filters and the drain pumps. The maximum delivery head is 1 m.

Service Water-proof syst.

The water protection system has reacted. Close the stopcock. Call the Service Department.

Service Fault F There is a fault. Disconnect the washing machine from the mains

electricity supply, either by switching off at the wallsocket and withdrawing the plug, or by discon-necting the relevant fuse on the mains fuse board.

Wait at least 2 minutes, before reconnecting thewashing machine to the mains electricity supply.

Then switch the washing machine on again. Restart the programme.

If the fault message appears again, contact theService Department.

To switch off the fault messages: Switch the washing machine off with the but-ton.


64

A message appears in the display at the end of the programme


Check filter + jet The pumps are dirty. Clean the pumps as described in "Problem solving

guide - Opening the door in the event of a blockeddrain outlet and/or power failure"

Start the programme again after cleaning thepumps.

The jet in the top of the door ring is blocked with fluff. Remove the fluff with your finger. Do not use any

sharp or pointed tools to do this. Start the programme again after cleaning the jet.

If the fault message appears again, contact the Ser-vice Department. The washing machine can still beused but with reduced functionality.

Align the machine The smoothing process which the laundry undergoesat the end of the programme could not be carried outproperly. Check whether the washing machine is aligned

correctly as described in "Installation and connec-tion - Levelling the machine".

Check whether the maximum delivery height of1 m has been exceeded.

If the fault message appears again, contact the Ser-vice Department. The washing machine can still beused but with reduced functionality.

The messages will appear at the end of the programme and when the washingmachine is switched on and need to be confirmed with the OK sensor.


65

A message appears in the display at the end of the programme


Check dosage Excessive foam has built up during washing. Check the amount of detergent dispensed. With automatic detergent dispensing check the

dosage amount set. Observe the instructions on the detergent pack-

aging and the degree of soiling of the laundry. If necessary, reduce the dosage amount by incre-

ments of 10%.

Hygiene info A programme using a temperature above 60 °C hasnot been run for a long time. In order to prevent bacteria and unpleasant odours

building up in the machine, run the Maintenancewash programme using Miele machine cleaner orpowder detergent.



66

A message about the TwinDos System has appeared in thedisplay


Cartridge almostempty

The detergent in the cartridges is running low. Thereare between 4 and 8 wash cycles remaining. Order new cartridges.

Container empty The cartridges or TwinDos containers are empty. Replace the cartridges or refill the TwinDos con-

tainers. Check whether the laundry is clean. If it is not

there may not have been enough detergent. If necessary, wash the items again.

Use "TwinDos" orstart Maintenance.See

TwinDos or automatic dispensing via compartment and/or has not been used for a long time. Use TwinDos for one of your next loads. Carry out the TwinDos maintenance programme as

described in "Cleaning and care", "TwinDos main-tenance".

TwinDos Maint. forcompart. and must be started. See

TwinDos or automatic dispensing via compartment and/or has not been used for a long time. It is pos-sible that detergent has dried inside the hoses. Carry out the TwinDos maintenance programme

immediately as described in "Cleaning and care","TwinDos maintenance".

The messages shown on this page are examples. They may differ depending onwhether they refer to compartment or .



67

Problems with TwinDos


No detergent and/orfabric conditioner wasdispensed.

Automatic dispensing has not been activated. Touch the Dos sensor before running the next

programme.

Automatic dispensing will be activated.No detergent/fabric conditioner was dispensed eventhough automatic dispensing was activated. Try again. If detergent is still not dispensed, call the Service

Department.

There are dark specksin the liquid detergent.

Mould has developed in the detergent. Pour the liquid detergent out of the container and

then clean the container thoroughly.


68

General problems with the washing machine


The machine shakesduring the spin cycle.

The machine feet are not level. Level the machine and adjust the feet correctly.

The laundry has notbeen spun properly andis still wet.

The machine detected an imbalance during the finalspin cycle and reduced the spin speed automatically. Include both large and small items in the load as

this will give better distribution during spinning.

Strange pump noisescan be heard.

This is not a fault.These slurping noises occur at the end of the pumpsequence as a normal part of operation.

Large amounts of deter-gent residue remain inthe detergent dispenserdrawer.

The water pressure is too low. Clean the water inlet filter. It may be useful to select the Water plus option.

Powder detergent used in conjunction with watersofteners tends to become sticky. In future, add washing powder into the dispenser

drawer first, and then add the water softener.

Fabric conditioner is notcompletely dispensedor too much water re-mains in the com-partment.

The siphon tube is not correctly positioned or isclogged. Clean the siphon, see "Cleaning and care - Clean-

ing the detergent dispenser drawer".

At the end of the pro-gramme there is still li-quid in the capsule.

The small pipe in the detergent dispenser drawer ontowhich the capsule is placed is blocked. Clean the small pipe.

This is not a fault.For technical reasons a small amount of water will re-main in the capsule.


69

General problems with the washing machine


There is water next tothe capsule in the fabricconditioner compart-ment.

The Cap sensor was not activated or an emptycapsule was not removed at the end of the last pro-gramme. Make sure that you remember to activate the Cap

sensor the next time you insert a capsule. Remove and then dispose of the empty capsule at

the end of each programme.The small pipe in the detergent dispenser drawer ontowhich the capsule is placed is blocked. Clean the small pipe.

The washing machinesmells.

Hygiene info was ignored. A wash programme using atemperature above 60 °C has not been run for a longtime. In order to prevent bacteria and unpleasant odours

building up in the washing machine, run the Main-tenance wash programme using Miele machinecleaner or a universal powder detergent.

The door and the detergent dispenser drawer wereleft open after washing. Leave the door and the detergent dispenser

drawer slightly open to allow them to dry.

The display is in a dif-ferent language.

A different language has been selected in "Settings,Language ". Set the language you want. The flag symbol will

guide you.

The display is dark. The display has switched off automatically to saveenergy (Standby mode). Press a button. Standby comes to an end.


70

An unsatisfactory wash result


Liquid detergent doesnot give the requiredresult.

Liquid detergents usually contain no bleachingagents. They do not remove fruit, coffee and teastains. Use the Miele 2 Phase System. The targeted addi-

tion of UltraPhase 2 during the wash process re-moves stains effectively.

Use a general purpose powder detergent contain-ing a bleaching agent.

Grey, greasy particlescling to washed laundry.

Insufficient amounts of detergent were used to breakdown the particles of grease in heavily soiled laundry. Use more detergent. Before washing the next load, run the Maintenance

wash using Miele machine cleaner or a powder de-tergent.

White residues whichlook like powder deter-gent are seen on darktextiles after washing.

The detergent contained compounds (zeolites) to aidwater softening which are not soluble in water. Thesehave ended up on the laundry. Try and brush off the residues with a soft brush

once the laundry is dry. Wash dark textiles using a detergent which con-

tains no zeolites. Liquid detergents usually containno zeolites.

Use the Dark garments / Denim programme fordark coloured laundry.


71

The door will not open


The door cannot bepulled open during aprogramme.

The drum is locked during a programme. Press the Start/Stop button. Use the sensor to select Cancel programme or

Add laundry.

The door will unlock and you will be able to pull itopen.There is still water in the drum and the machine is un-able to drain. Clean the drain filter and the drain pump as de-

scribed in "Opening the door in the event of ablocked drain outlet and/or power failure".

The water level in the drum is too high. Cancel the programme. The water will be pumped

away.

Comfort coolingappears in the displayafter a programme hasbeen cancelled.

For safety reasons the drum door cannot be opened ifthe suds temperature is higher than 55 °C. Wait until the temperature in the drum has de-

creased and the message has gone out in the dis-play.

The following appearsin the display: Service Door release

The door lock has jammed. Call the Service Department.


72

Opening the door in the eventof a blocked drain outlet and/or power failure Switch off the washing machine.

Press the drain pump access panel.

The panel will spring open.

Blocked drain outlet

If the drain outlet is blocked, a largequantity of water can remain in thewashing machine.

If laundry has been washed at ahigh temperature, water draining outof the machine will still be hot.Danger of scalding!Take care when draining the ma-chine.

Procedure for draining the washingmachine

When draining water from the ma-chine, do not unscrew the drain fil-ters completely or take them rightout.

Place a suitable container, e.g. aMiele universal oven tray under theaccess panel.

Slowly and carefully unscrew the fil-ters to let the water out. Be carefulnot to release too much water atonce. If the flow of water is toostrong, some water can seep into thewashing machine base and activatethe water protection float switch. Thiswill prevent the washing machinefrom functioning.

Tighten the drain filters back up againif you need to interrupt the flow ofwater.

Once the flow of water ceases:


73

Remove the drain filters completely.

Clean them thoroughly.

Remove any foreign objects (e.g. but-tons, coins, etc.) and fluff from the fil-ter housing. Turn the impellers byhand to check that they rotate freely.

Replace the drain filters correctly (onthe right and left) and tighten themsecurely.

Water leaking from the washingmachine can cause damage.Replace and tighten the drain filterssecurely.

Opening the door

Always make sure that the drumis stationary before reaching in to re-move laundry. Reaching into a mov-ing drum is extremely dangerous.

Use a screwdriver to unlock the door.

Pull open the door.

After sales service

74

RepairsIn the event of any faults which youcannot remedy yourself, please contact:

– your Miele Dealer, or

– Miele (Contact details for Miele aregiven at the end of this booklet).

When contacting your Dealer or Miele,please quote the model and serial num-ber of your machine, both of which areshown on the data plate visible abovethe porthole glass when the door isopen.

N.B. A call-out charge will be appliedfor service visits where the problemcould have been resolved as de-scribed in these instructions.

Optional accessoriesOptional spare parts and accessoriesfor this washing machine are availablefrom your Miele Dealer, the Miele SpareParts Department or via the internet atwww.miele-shop.com.

Please note that telephone calls maybe monitored and recorded for trainingpurposes.

Warranty: U.K.In the U.K, the washing machine war-ranty is valid for 2 years from the dateof purchase.

In the U.K. you must activate your coverby calling 0330 160 6640 or registeringonline at www.miele.co.uk.

Warranty: Other countriesFor information on the appliance war-ranty specific to your country pleasecontact Miele. See end of this bookletfor contact details.

Installation and connection

75

Front view

a Inlet hose with Waterproof system

b Electrical supply cable

c Flexible drain hose (with detachableswivel elbow)

d Control panel

e Detergent dispenser drawer

f Door

g Access to drain filter, drain pump andemergency release

h Access panel for TwinDos containers

i Four height adjustable feet


76

Rear view

a Drain hose

b Transport clips for electrical supplycable, inlet and drain hoses

c Electrical supply cable

d Protruding lid for holding when mov-ing the machine

e Inlet hose with Waterproof system

f Safety caps for transit bars

g Transport clips for inlet and drainhoses and for storing transit barswhen not in use


77

Installation surfaceA concrete floor is the most suitable in-stallation surface for a washing ma-chine, being far less prone to vibrationduring the spin cycle than woodenfloorboards or a carpeted surface.

Please note:

The machine must be level and se-curely positioned.

To avoid vibrations during spinning,the machine should not be installedon soft floor coverings.

If installing on a wooden joist floor:

We recommend a plywood base atleast 59 x 52 x 3 cm). The baseshould span several joists and bebolted to the joist and not only thefloorboards. Check for the presenceof pipes and cables first.

Tip: If possible, install the machine in acorner, as this is usually the most stablepart of the floor.

There is the danger of the wash-ing machine moving about duringspinning and falling off a plinth.For this reason, if the machine is in-stalled on a raised plinth (concrete orbrick), it has to be secured againstslippage using an MTS floor/plinthmounting kit (available from Miele).

Transporting the washing ma-chine to its installation site

Make sure the fixings at the backof the lid are secure.Otherwise there is a danger of the lidbeing pulled off when carrying themachine.Before carrying the machine checkthat the lid is secure where it pro-trudes at the back of the machine.

Carry the washing machine by thefront feet and the protruding lid at theback.

Removing the transit bars

To remove the left and right covers

1. Pull on the attached stopper,

2. then use a screwdriver to release thecatches at the top and bottom.


78

Using the spanner supplied, turn theleft-hand transit bar 90°, then

pull the transit bar out.

Turn the right-hand transit bar 90°,then

pull the transit bar out.


79

To avoid the risk of injury, theholes for the transit bars must becovered after the transit bars havebeen removed.

Plug the holes with the plastic capsas illustrated.

Secure the transit bars to the back ofthe washing machine. Make sure thetop catch is located above the holder.

The washing machine must notbe moved without the transit bars inplace. Store them as shown or keepthem in a safe place for future use.They must be re-fitted if the machineis to be moved again (e.g. whenmoving house).

Re-fitting the transit barsRe-fitting is carried out by reversing theprocedure.


80

Levelling the machineThe washing machine must stand per-fectly level on all four feet to ensuresafe and proper operation.

Incorrect installation may increase elec-tricity and water consumption and maycause the machine to move about.

Screwing out and adjusting the feet

The four adjustable screw feet are usedto level the machine. All four feet arescrewed in when the machine is de-livered.

Using the spanner supplied turncounter nut 2 in a clockwise direction.Then turn counter nut 2 together withfoot 1 to unscrew.

Use a spirit level to check that thewashing machine is standing level.

Hold foot 1 securely with a pipewrench. Turn counter nut 2 again us-ing the spanner supplied until it sitsfirmly up against the housing.

All four counternuts must befirmly up against the housing. Pleasealso check this for the feet which didnot need adjustment. Otherwisethere is a danger of the machinemoving about.


81

Building under a continuous work-top/ in a kitchen run

Building under kits* must only be in-stalled/dismantled by a suitably qual-ified fitter in accordance with the in-structions supplied.

– A special building under kit* with acover plate to replace the machine lidis required. It must be fitted by a suit-ably qualified fitter to ensure elec-trical safety. N.B. If there is space topush the washing machine under theworktop without removing the lid, thebuilding under kit is not necessary.Otherwise it is essential.

– Connections for electricity, water anddrainage should be installed in such away that they remain accessiblewhen the machine is in its final posi-tion.

Fitting instructions are supplied with theconversion kit.

Washer-dryer stack

The washing machine can be combinedwith a Miele tumble dryer in a washer-dryer stack. The appropriate "WTV"stacking kit* to match your dryer is re-quired.

All parts marked* are available fromyour Dealer or Miele.

Please note:

a = at least 2 cm

b = WTV without drawer: 172 cmWTV with drawer: 181 cm

c = 64 cm


82

The water protection systemThe Miele water protection system pro-tects all parts of the washing machinefrom water damage.

The system consists of three main com-ponents:

– the inlet hose

– the electronic unit and drainage andoverflow protection

– the drain hose

The Waterproof System (WPS)

3

5

4

2

1

6

a Two solenoid valves

b Double-skinned inlet hose

c Sump

d Float switch

e Electronic unit

f Drain pump

Inlet hose

– The casing on the inlet hose containstwo solenoid valves , which cut offthe water intake directly at the stop-cock. These valves provide two-foldprotection. In the event that one ofthe valves is faulty, the other valvewill cut off the water intake.Blocking the water intake at the stop-cock means that the inlet hose is onlyunder pressure whilst water is beingtaken into the machine. For the re-mainder of the time, pressure on theinlet hose is negligible.

– Protection against the solenoidvalves burstingThe solenoid valves are pressuretested to between 7,000 kPa and10,000 kPa against bursting.

– The double-skinned inlet hose hasa pressure-resistant inner hose and aprotective sleeve. Any leaking wateris fed into the sump through thisprotective sleeve. A float switch closes the solenoid valves, prevent-ing any more water flowing into themachine and water in the suds con-tainer is pumped away.


83

The electronic unit and drainageand overflow protection

– Drainage protectionAny leaking water is collected in thesump in the base of the machine.A float switch closes the solenoidvalves , preventing any more waterfrom flowing into the machine andwater in the suds container ispumped away.

– Overflow protectionIf the water level exceeds a certainlevel, the drain pump switches inand pumps the excess water away ina controlled manner.Should the water level rise repeatedlyin an uncontrolled way, the drainpump will switch on continuously,the washing machine will indicatethat there is a fault and a tone willsound.

Drain hose

The drain hose is protected by a ventila-tion system which prevents the washingmachine from being emptied com-pletely.


84

Connection to the water supply

The casing on the water inlethose contains electrical components.It must not be connected in areaswhere there is the risk of water orother liquids reaching it, e.g. bath-rooms.

The casing on the water inlet hosemust not get wet.

The protective sleeve of the hosemust not be damaged or kinked.

The washing machine should be con-nected to a mains water supply in ac-cordance with current local and nationalsafety regulations. The German author-ities do not require it to have a non-re-turn valve as the washing machine hasbeen designed to comply with DIN reg-ulations.

The machine is designed to operatewith a flow pressure of between 100and 1,000 kPa. If it is higher than1,000 kPa it is essential to fit a pressurereducing valve.

Connection to the mains water supplyshould incorporate a mains stopcockwith a ¾" threaded union. The stopcockshould be fitted by a qualified plumber.

The connection point is subjectto mains water pressure. Turn on thestopcock slowly and check for leaks.Correct the position of the washerand union if appropriate.

The washing machine is not suitablefor connection to a hot water supply.


85

Maintenance

Only use a Miele Waterproof systemhose should you need a replacement.Disconnect the machine from the elec-tricity supply before unscrewing the wa-terproof system inlet hose from thestopcock.

In order to protect the water inletvalve, the dirt filter in the water inletvalve connection must not be re-moved.

Extension hose

A 1.5 metre long (metal) extension hoseis available from your Miele dealer orthe Miele Spare Parts Department as anoptional extra.This hose is tested towithstand pressures of up to14,000 kPa and can be used as a flex-ible extension to the water supply. N.B.Using this hose will render the Watersystem safety valve on the inlet hose in-effective.


86

DrainageThe suds are drained through a drainpump with a 1 m delivery head. For thewater to drain freely, the hose must beinstalled free of kinks. The elbow piecesupplied hooks onto the end of thehose.If required, the hose can be extended toa length of up to 5 m. The necessaryparts can be ordered from Miele.

For a delivery head of more than 1 m(up to a max. of 1.8 m) a replacementdrain pump will need to be fitted.Please contact Miele for advice.If required, the hose can be extended toa length of up to 2.5 m. The necessaryparts can be ordered from Miele.

Drainage options:

1. Directed into a sink or basin:

Please note:

– Hook the hose over the edge andsecure it.

– If the water is pumped into awashbasin, make sure that it candrain away freely. Otherwise thereis a risk of water overflowing or ofsome of the drained water beingsucked back into the machine.

2. Connected securely to a plastic drainpipe with a rubber nipple (there is noneed to use a siphon).

3. Connected securely to a floor gully.

4. Connected securely to a washbasinwith a plastic nipple.

Please note:

a Adapter

b Spigot nut

c Hose clip

d End of the hose

Fit adapter to the sink drain outletusing nut .

Attach the end of hose to adapter.

Use a screwdriver to tighten hose clip up close to the nut.


87

Electrical connection U.K.All electrical work should be carried outby a suitably qualified and competentperson, in strict accordance with cur-rent national and local safety regula-tions (BS 7671 in the UK).

Ensure power is not supplied to the ap-pliance until after installation work hasbeen carried out.

The appliance is supplied with a mainscable with moulded plug ready for con-nection to a 230-240V mains supply.

Please ensure the connection dataquoted on the data plate match thehousehold mains supply.

Connection should be made via a suit-able switched socket which is easily ac-cessible after installation.

For extra safety it is advisable to protectthe machine with a suitable residualcurrent device (RCD). Contact a quali-fied electrician for advice.

Do not connect via an extension lead.Extension leads do not guarantee therequired safety of the appliance (e.g.danger of overheating).

Non-rewireable plugs BS 1363

The fuse cover must be refitted whenchanging the fuse, and if the fuse coveris lost, the plug must not be used until asuitable replacement is obtained. Thecolour of the correct replacement coveris that of the coloured insert in the baseof the plug, or the colour that is em-bossed in words on the base of theplug (as applicable to the design of plugfitted).

Replacement fuses should be ASTA ap-proved to BS 1362 and have the correctrating. Replacement fuses and fusecovers may be purchased from yourlocal electrical supplier.

WARNING: THIS APPLIANCE MUSTBE EARTHED

Consumption data

88

Load Energy Water Duration Residualmoisture

kg kWh Litres h:min %

Cottons 90 °C 9.0 2.40 65 2:29 50

60 °C 9.0 1.45 65 2:29 50

60 °C 4.5 1.10 52 2:19 50

* 9.0 0.80 54 2:59 44

* 4.5 0.50 49 2:59 44

40 °C 9.0 1.20 61 2:39 50

40 °C 4.5 0.45 36 1:19 50

* 4.5 0.35 42 2:59 44

20 °C 9.0 0.40 72 2:39 46

Minimum iron 30 °C 4.0 0.50 52 1:59 30

Delicates 30 °C 3.0 0.40 40 1:09 –

Woollens 30 °C 2.0 0.23 35 0:38 –

Automatic plus 40 °C 6.0 0.77 55 1:59 –

QuickPowerWash 40 °C 5.0 0.75 45 0:59 –

Express 201) 40 °C 3.5 0.30 25 0:20 –

Shirts2) 60 °C 2.0 0.76 40 1:31 –

1) Short option activated

2) Pre-ironing option deactivated

Consumption data

89

Note for test institutes*Test programme in accordance with EN 60456 and energy label with Directive 1061/2010

Consumption data can vary from the nominal values given depending on waterpressure, water hardness, water inlet temperature, room temperature, type andvolume of load, fluctuations in the electricity supply and any options selected.

With the PowerWash 2.0 washing technique, during the heating phase, the tem-perature measured by the sensor in the suds container is higher than the actualtemperature of the laundry.The temperature measured there does not reflect the temperature of the laun-dry.

The consumption data shown in the EcoFeedback display can vary from theconsumption data quoted here. The variations arise from component tolerancesand on-site conditions e.g. fluctuations in the pressure of the water supply,mains voltage and fluctuations in the mains voltage.

90

Technical data

91

Height 850 mm

Width 596 mm

Depth 636 mm

Depth with door open 1054 mm

Height for building under 820 (+8/-2) mm

Width for building under 600 mm

Weight Approx. 100 kg

Capacity 9 kg dry laundry

Voltage See data plate

Connected load See data plate

Fuse rating See data plate

Consumption data See "Consumption data"

Minimum flow pressure 100 kPa

Maximum flow pressure 1000 kPa

Inlet hose length 1.60 m

Drain hose length 1.50 m

Mains connection cable length 2.00 m

Delivery head max. 1.00 m

Maximum drainage length 5.00 m

LEDs Class 1

Test certificates awarded See data plate

Technical data

92

Data sheet household washing machinesIn acc. with delegated regulation (EU) No. 1061/2010

MIELE

Model name / identifier WKH 122 WPS

Rated capacity1 9,0 kg

Energy efficiency class

A+++ (most efficient) to D (least efficient) A+++

Annual energy consumption (AEc)2 130 kWh/year

Energy consumption of the standard "60°C cotton programme" at full load 0,80 kWh

Energy consumption of the standard "60°C cotton programme" at partial load 0,50 kWh

Energy consumption of the standard "40°C cotton programme" at partial load 0,35 kWh

Weighted power consumption in off-mode (Po) 0,10 W

Weighted power consumption in the left-on mode (Pl) 3,00 W

Weighted annual water consumption (AWc)3 11.000 Litres/year

Spin-drying efficiency class

A (most efficient) to G (least efficient) A

Maximum spin speed4 1.600 1/min

Remaining moisture content4 44 %

Standard programme to which the information in the label and the fiche relates5 Cottons 60/40 with

arrow

Programme time of the standard programme

60°C cotton programme (full load) 179 min

60°C cotton programme (partial load) 179 min

40°C cotton programme (partial load) 179 min

Duration of the 'left-on' mode (Tl)6 15 min

Airborne acoustical noise emissions

Washing phase7 46 dB(A) re 1 pW

Spinning phase7 72 dB(A) re 1 pW

Built-in -

This product does not release silver ions during the washing cycle.

● Yes, standard feature1

In kg of cotton for the standard "60 °C cotton programme "at full load or the "40 °C cotton pro-gramme" at full load, whichever is the lower.

2Based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and partialload, and the consumption of the low-power modes. Actual energy consumption will depend on howthe appliance is used.

Technical data

93

3Based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and partialload. Actual water consumption will depend on how the appliance is used.

4Attained for the standard "60 °C cotton programme" at full load or the standard "40 °C cotton pro-gramme" at partial load, whichever is the lower, and remaining moisture content attained for thestandard "60 °C cotton programme" at full load or the standard "40 °C cotton programme" at partialload, whichever is the greater.

5These programmes are suitable to clean normally soiled cotton laundry and are the most efficientprogrammes in terms of combined energy and water consumption.

6If the household washing machine is equipped with a power management system.

7For the standard "60 °C cotton programme" at full load.

Settings

94

You can use the settings menu to alterthe machine's electronics to suit chan-ging requirements.

Settings can be altered at any time.

To access Settings

Before you begin, ensure that:

– The washing machine is switched on.

– The standard display is showing.

OK

2:59 1600

Touch the and sensors at thesame time.

Language You are now in the Settings menu.

Selecting a setting

Touch the or sensor until thesetting you want appears in the dis-play.

– The sensor scrolls down the list.

– The sensor scrolls up the list.

Touch the OK sensor to select thesetting displayed.

Changing a setting

Touching the sensor will call up thedifferent options for the setting.

The option which is selected will havea tick next to it.

When the option you want shows inthe display touch the OK sensor toactivate it.

To exit Settings

Touch the and sensors at thesame time or turn the programme se-lector.

Settings

95

Language

The display can be set to appear inone of several different languages.

The flag after the word Language actsas a guide to prevent a language whichwill not be understood from being set.

The selected language will be stored inmemory.

TwinDos

You can set the type and amount ofdetergent and also start a cleaningprogramme for the TwinDos system.

Detergent/amount

The washing machine is pre-set asstandard for UltraPhase 1 andUltraPhase 2 for hardness range II ().

The settings must be changed in theelectronics:

– for water hardness range I () andwater hardness range III ().

– when changing to a different deter-gent or fabric conditioner. TheTwinDos containers (optional ac-cessories) are required for this.

Dosage amounts for UltraPhase 1 andUltraPhase 2

UltraPhase 1 48 ml 60 ml 72 ml

UltraPhase 2 36 ml 45 ml 54 ml

Adjusting the dosage amount

Detergent / amount Touch the OK sensor.

Compartment Touch the OK sensor.

Miele UltraPhase 1


Dosage - ml60

Use the and sensors to adjustthe dosage amount as required andconfirm this value with the OK sensor.

Set dosage for UltraPhase 2


Dosage - ml45

Use the and sensors to adjustthe dosage amount as required andconfirm this value with the OK sensor.

The dosage amount has been adjusted.

Settings

96

Changing the detergent type

Dosage amounts for Miele products(e.g. UltraColor, Miele fabric condi-tioner) are pre-set for water hardnessrange II ().

Detergent / amount Touch the OK sensor.


Miele UltraPhase 1

Select the detergent you want usingthe and sensors and confirmyour selection with the OK sensor.

Miele UltraColor

Dosage - ml105

Confirm the amount of detergent withthe OK sensor or change this usingthe and sensors.

Settings for compartment cancelled


The setting has been changed for com-partment . You can now change thesetting for compartment .

Use the and sensors to selectcompartment


Not defined

Select the detergent you want usingthe and sensors and confirmyour selection with the OK sensor.

Miele conditioner

Dosage - ml70

Confirm the amount of detergent withthe OK sensor or change this usingthe and sensors.

The electronics are set for the new de-tergent.

Maintenance

The washing machine has a cleaningprogramme for cleaning the TwinDossystem containers and the hoses in-side the washing machine.

The TwinDos system must be cleaned ifthe system has not been used for along period of time or if you are chan-ging brand of liquid detergent or fabricconditioner. See "Cleaning and care","TwinDos maintenance" for more de-tails.

Settings

97

Degree of soiling

You can select the default setting forthe degree of soiling or switch off thedegree of soiling query.

Options

– Default settingYou can choose between the Light,Normal or Heavy degree of soilingsettings.Factory default setting: Normal.

– QueryYou can switch the degree of soilingquery on or off. Factory default setting: On

Buzzer volume

You can select one of seven differentsettings for the buzzer volume.

The settings are represented by a barchart. At the lowest setting, the buzzeris switched off.

Keypad tone

Each touch of a sensor or press of abutton is confirmed with an audibletone.

Factory default setting: the keypad toneis switched on.

Consumption

In this setting you can check thesaved energy and water consumptionvalues.

Options

– last programmeShows the consumption for the lastwash programme carried out.

– DisplayShows the sum of the energy and thesum of the water used by the previ-ous programmes.

– Reset functionThe energy consumption and waterconsumption totals are reset to zero.

Settings

98

Code

The code prevents the washing ma-chine being used without your know-ledge.

Options

– ActivateThe code is 125 and can be activ-ated.When the code has been activated,you have to enter the code afterswitching the washing machine on.Otherwise the washing machine can-not be operated.

– DeactivateFor using the washing machinewithout entering the code. This onlyappears if the code has been activ-ated previously.

– ChangeYou can enter a code of your own.

Important. Make a note of your newcode. If you forget the code, thewashing machine will need to be un-locked by Miele Service.

Temperature unit

The temperature can be displayed asdegrees Celsius (°C) or Fahrenheit (°F).

Factory default setting: Celsius (°C).

Display brightness

There are seven different displaybrightness settings.

The brightness changes as soon as youselect a different setting.

Dark display

To save energy, the display will go outand the Start/Stop button will flashslowly.

Options

– OnThe display will go out after 10minutes.

– On (not in current programme)The display will remain on while theprogramme is running but will go out10 minutes after the end of the pro-gramme.

– OffThe display will remain on.

Factory default setting: the On (not incurrent programme) option is selected.

Settings

99

Machine switch-off

The washing machine will switch offautomatically after the end of the pro-gramme/anti-crease phase or after be-ing switched on if no further selectionis made.

Options

– 15 minutes (Factory default setting)The washing machine will switch it-self off after 15 minutes.

– 20 minutesThe washing machine will switch it-self off after 20 minutes.

– 30 minutesThe washing machine will switch it-self off after 30 minutes.

Display maximum load

After a programme is selected themaximum load appears in the displayfor a short time.

You can choose whether the maximumloading capacity is displayed or not.

Factory default setting: Display max-imum load is switched on.

Display programme name

The name of the selected programmeis shown briefly in the display.

You can choose whether the pro-gramme name is displayed or not.

Factory default setting: the Display pro-gramme name setting is switched off.

Memory

The washing machine will save thesettings (temperature, spin speed andsome of the options) which have beenselected for a programme after theprogramme has started.

When this programme is chosen again,these saved settings will appear in thedisplay.

Factory default setting: the Memoryfunction is switched off.

Settings

100

Pre-wash Cottons

If you require a longer pre-wash youcan extend the Cottons programme'sstandard pre-wash time of 25 minutes

Options

– No increase (Factory default setting)25 minute pre-wash

– +6 min31 minute pre-wash



Gentle action

Activating gentle action reduces thedrum action and is suitable for wash-ing slightly soiled items more gently.

Gentle action can be activated for theCottons and Minimum iron pro-grammes.

Factory default setting: Gentle action isswitched off.

Reduce temp.

The boiling point for water is lower athigh altitudes. In order to avoid waterboiling, Miele recommend activatingthe reduce temperature setting at alti-tudes of more than 2000 m above sealevel. The maximum temperature is re-duced to 80 °C even when a highertemperature is selected.

Factory default setting: the reduce tem-perature setting is switched off.

Water plus

You can increase the set amount ofwater in the wash programmes.

Options

– Water +The water level is increased in thewash and rinse stages.

– Extra rinseAn extra rinse is carried out.

– Water + and Extra rinseThe water level is increased in thewash and rinse stages and an extrarinse is carried out.

Settings

101

Water plus level

The water level can be increased in 4stages by activating the Water plusoption.

Stages:

– Normal (Factory default setting)

– Plus

– Plus

– Plus

Maximum rinse level

The water level in the rinse cycle canbe permanently set to the highestvalue.

This function is useful for allergy suffer-ers as it achieves an excellent rinse res-ult. Water consumption will increase.

Factory default setting: the maximumrinse level setting is switched off.

Suds cooling

When this is activated, additional wa-ter flows into the drum at the end ofthe main wash to cool the suds down.Hot suds can damage plastic drainagepipes.

Suds cooling takes place when a tem-perature of 70 °C or higher is selectedfor the Cottons programme.

Suds cooling should be activated:

– to prevent the danger of scalding ifthe drain hose is hooked over theedge of a sink or basin.

– where drainage pipes do not complywith DIN 1986.

Factory default setting: Suds cooling isswitched off.

Settings

102

Low water pressure

If the water pressure is less than 1 bar(100 kPa) the programme will be can-celled and the fault message Water in-take See will appear.

If the on-site water pressure cannot beincreased, activating this function willprevent the programme from being can-celled.

Factory default setting: Low water pres-sure is switched off.

Anti-crease

The anti-crease function helps preventcreasing if laundry is not going to beremoved immediately after the end ofthe programme.

The drum continues to turn at intervalsfor up to 30 minutes at the end of theprogramme. The door can be opened atany time.

Factory default setting: anti-crease isswitched on.

Optional accessories

103

Detergent, fabric care, additives andmachine care products are available forthis washing machine. All the productshave been designed for Miele washingmachines.

These and many other useful productscan be ordered via the internet atwww.miele-shop.com or from Miele(see end of this booklet for contact de-tails).

Detergent

UltraPhase 1 and UltraPhase 2

– universal liquid detergent and deter-gent enhancer dispensed as twocomponents.

– suitable for white and coloured laun-dry

– no need to refill as the componentsfor the TwinDos system are suppliedin single use cartridges.

UltraWhite

– powder detergent

– suitable for white and light colouredlaundry as well as heavily soiled cot-ton items

– effective stain removal even at lowtemperatures

UltraColor

– liquid detergent for coloureds

– suitable for coloured and dark/blackgarments

– protects bright colours from fading

– effective stain removal even at lowtemperatures

Wool and delicates detergent

– liquid detergent for delicates

– particularly suitable for woollen andsilk garments

– cleans at temperatures as low as20 °C, helps retain the shape of delic-ate garments and protect colours

Specialist detergentsSpecialist detergents are available ascapsules in convenient single doseamounts or in a handy bottle.

Outdoor

– liquid detergent for outerwear andperformance clothing

– cleans with care and is gentle on col-ours

– with lanolin to care for and conditionmembrane fabric

Sport

– liquid detergent for sportswear andfleece garments

– neutralises unpleasant odours

– retains the shape of the textiles

Optional accessories

104

Down items

– liquid detergent suitable for pillows,sleeping bags and down filled items

– retains the elasticity of down andfeather filled items

– retains the breathability of down filleditems

– prevents down filling clumping to-gether

WoolCare

– liquid detergent for woollens and del-icates

– with a special wheat protein condi-tioning formula

– helps prevent pilling

– gentle on colours

– only available as capsules

SilkCare

– liquid detergent for silks

– with a special silk protein condition-ing formula

– gentle on colours

– only available as capsules

Fabric careFabric care agents are available as cap-sules in convenient single doseamounts or in a handy bottle.

Proofing agent

– for reproofing microfibre garmentse.g. rain coats etc.

– retains the breathability of garments

Fabric conditioner

– fresh, natural fragrance

– makes laundry soft to handle

Additives

Booster

– for removing stains

– suitable for white and coloured laun-dry

– available as capsules in conveni-ent single dose amounts

Machine care products

Machine cleaner

– for cleaning the washing machinethoroughly and effectively

– removes grease, bacteria and un-pleasant odours

Descaling agent

– removes heavy limescale deposits

– mild and gentle with natural citricacid

United KingdomMiele Co. Ltd.Fairacres, Marcham RoadAbingdon, Oxon, OX14 1TWCustomer Contact Centre Tel: 0330 160 6600E-mail: [email protected]: www.miele.co.uk

AustraliaMiele Australia Pty. Ltd.ACN 005 635 398ABN 96 005 635 3981 Gilbert Park DriveKnoxfield, VIC 3180Tel: 1300 464 353Internet: www.miele.com.au

Miele (Shanghai) Trading Ltd.1-3 Floor, No. 82 Shi Men Yi RoadJing' an District200040 Shanghai, PRCTel: +86 21 6157 3500Fax: +86 21 6157 3511E-mail: [email protected],Internet: www.miele.cn

China

41/F - 4101, Manhattan Place23 Wang Tai RoadKowloon Bay, Hong KongTel: (852) 2610 1025Fax: (852) 3579 1404Email:[email protected]: www.miele.hk

Miele (Hong Kong) Limited

Miele India Pvt. Ltd.Ground FloorCopia Corporate SuitesPlot No. 9, JasolaNew Delhi - 110025Tel: 011-46 900 000Fax: 011-46 900 001E-mail: [email protected]: www.miele.in

India

Miele Ireland Ltd.2024 Bianconi AvenueCitywest Business CampusDublin 24Tel: (01) 461 07 10Fax: (01) 461 07 97E-Mail: [email protected]: www.miele.ie

Ireland

MalaysiaMiele Sdn BhdSuite 12-2, Level 12Menara Sapura KencanaPetroleumSolaris Dutamas No. 1Jalan Dutamas 150480 Kuala Lumpur, MalaysiaPhone: +603-6209-0288Fax: +603-6205-3768

Miele New Zealand LimitedIRD 98 463 631Level 2, 10 College HillFreemans Bay, Auckland 1011New ZealandTel: 0800 464 353Internet: www.miele.co.nz

New Zealand

Miele Pte. Ltd.163 Penang Road# 04 - 03 Winsland House IISingapore 238463Tel: +65 6735 1191Fax: +65 6735 1161E-Mail: [email protected]: www.miele.sg

Singapore

Miele (Pty) Ltd63 Peter Place, Bryanston 2194P.O. Box 69434, Bryanston 2021Tel: (011) 875 9000Fax: (011) 875 9035E-mail: [email protected]: www.miele.co.za

South Africa

Miele Appliances Ltd.Gold & Diamond ParkOffice No. 6-217Sheikh Zayed RoadP.O. Box 11 47 82 - DubaiTel. +971 4 3044 999Fax. +971 4 3418 852800-MIELE (64353)E-Mail: [email protected]: www.miele.ae

United Arab Emirates

Manufacturer: Miele & Cie. KG, Carl-Miele-Straße 29, 33332 Gütersloh, Germany

K.E. & Kingstone Co., Ltd.6th Fl., No. 120, Sec. 2Jianguo N. Rd.Taipei, TaiwanTEL: +886 2 2502-7256FAX: +886 2 2502-3077E-mail: [email protected]:www.kenk.com.tw/ke/miele

Taiwan

ThailandBHIRAJ TOWER at EmQuartier43rd Floor Unit 4301-4303 689 Sukhumvit RoadNorth Klongton Sub-DistrictVadhana DistrictBangkok 10110, Thailand

M.-Nr. 10 655 500 / 01en-GB

WKH 122 WPS

Documents

Operating instructions for washing machinesThe washing machine can only be used by people with reduced physical, sensory or mental capabilities, or lack of experience or ... Unauthorised