-
OPERATING INSTRUCTIONS·
1100 LBS (500 KGS}
2�STAGE HYDRAULIC TRANSMISSION JACK
. . Capacity kg I -·
1" Stage ?"Stage
1000 500
SPECIFICATIONS
Heigh!
Low mm High mm
870 1847
S;;ddle Tilt
FWD ! BACK•.j
15°
r
I I Base Size mm I N.W.kg
1000:< 1000 84
·-
-
OPTIONS·
98
REVISED PARTS BREAKDOWN
ANGLE PLATE SET
79 80
REL'c:AS'c 'l.'•.LV'c SET
88
8
L,9 µo
B
(: 5052
0
-48
�
30
2028
1
27 26 44
C I 24
PUMP SET
CYLINDER SET
t2
3 -r-22
tr-21
20
19
18
46 105 (47
�\> HANDLE SETI ffi
0
1�
108 104 b
02 .v
y-17 16
13
12
10
09
3
-
Service and Maintenance Instructions for Hydraulic Transmission
Jack,
WARNING
. THE USE OF THIS JACK IS LIMITED TO THE REMOVAL, INSTALLATION.
ANO TRANSPORTATIOIN IN
THE LOWEST POSITION, Of' TRANSMISSIONS AND DlFfERNTIALS. IT MAY
BE USED WITH
APPROPRIATE ADAPTORS MANUFACT\;AEO ESPECIALLY FOR THE JACK TO
HANDLE OTHER
COMPONENTS: SUCH AS REAR AXLE UNITS AND TRANSFER CASE, WITHIN
THE WEIGHT
LIMITATIONS SPECIFIED.
2. 8E SURE THAT THE JACK IS A?PAOPRIATELY SUPPORTED BEFORE
STARTING REPAIRS.
J. DO NOT OVERLOADING CAN CAUSE DAMAGE TO OR FAILURE Of THE
JACK.
J THIS JACK IS DESIGNED FOR USE ONLY ON HARO U:VEL SURFACES
CA?ABLE OF SUSTAINING
THE LOAD. USE ON OTHER THAN HARD LEVEL SURFACES CAN RESULT IN
JACK INSTABILITY
AND POSSIBLE: LOSS OF LOAD.
5 FAILURE TO HEf.0 THESE WARNINGS MAY RESULT IN LOSS OF LOAD.
DAMAGE TO JACK. ANQIOR
FAILURE RESULTING !N PERSONAL OR PROPERTY DAMAGE.
M111intonanc:s
Tho hyQtaulic system is a �lo&ed sy$tam. ano w1H norma.Hy
dsmana no maintenance.
The me:chan1ca1 �ans ot lhe p,qda! must ba fraquenHy lubflcataO
with- a h19h·quaHty 01l.
Th& 01! levei mvst not come up over tha liiling ptug, when
1he transmission iac� is in ,ts lowest pos1t1ofl
When the lifting saddle can be pumped up to the lop position the
hydraulic system is 01160 �ilh enough orL
Quantify of 011: 3 I.
An·y good hydraul!e on of vl•co.ity 15'C SV 40'Coan oo uM
-
T �TY ·1I ' I
,._1'10. I DESCRIPTION I CYLINDER SET
Ol , 8ASE 02 i CYLINDER
I , . I 03 : RESERVOJR 1 1 ; 07 I O·RINGOil I RAM 09 I O·AING 10
: TOPNVT " : PACKING 12 0-RING 13 FLANGE 14 O.RING
15 DUST SEAL Hl WASHER 17 BOLT 18 RETAINER . RAM 19 I RAM
1 1 4 4
20 O·AING I 21 TOP NUT I 22 O·RING 2 29 DUST SEAL 1 , .
46 AIR VENT VALVE ASS'Y I 47 O·RING 1 1
l :: l :�� --!-W ,-- ,·-P-U_M_P_S_ET___ ! 1 I24 PUMP BASE
2' I25 STEEL SAU. 26 WASHER I 27 PUMP CYLINDER i 28 ' 0,RING
! 29 DUST SEAL 30 PUMP PISTON 31 SPRING 32 WASHER 33
1
. BOLT.CHECK VALVE 44 O·RING 45 HEXAGON SOCKET HEAD
CAPSCAEW 48 DUST CAP 49 SPRING 50 I SPRING RETAINER 51
CONNECTING ROD
1 t 2
4 1
4 I 52 SET SCREW �.. SPRING WASHER·---.
.+-
! RELEASE VALVE SET 34 0-AING35 RELEASE VALVE
,
1
3�6! SPRING BASE.RELEASE VALVE PIN PEDAL RELEASE VALVE
I 40 , PIN i 41 SNAP RING 'C' I 42 SPRING VVASHER
43 HEXAGON SOCKET HEAD I I CAP SCRE\f./
I- '1 PUMP PEDAL SET
53 I PEAOL PUMP PISTON 54 UNK
I 55 I CODER LINK
4
4
1 1 2
2
----;
I I
I !
DESCRIPTJON OTY-
1
