Operating and installation instructions Cooker hood€¦ · Compare this before connecting the appliance to the mains. Consult a qualified electrician if in any doubt. Do not connect

Operating and installation instructionsCooker hood

To prevent the risk of accidents or damage to the appliance, it isessential to read these instructions before it is installed and used forthe first time.

en-GB M.-Nr. 10 639 810

Contents

2

Warning and Safety instructions .......................................................................... 4

Caring for the environment ................................................................................ 13

Guide to the appliance ........................................................................................ 14

Modes of operation ............................................................................................. 16

Operation.............................................................................................................. 17Switching the fan on.............................................................................................. 17Selecting the power level ...................................................................................... 17Run-on time........................................................................................................... 17Switching the fan off ............................................................................................. 17Switching the hob lighting on/off .......................................................................... 17Power management .............................................................................................. 17

Switching Power management on/off .............................................................. 18Safety switch-off ................................................................................................... 18

Energy saving tips ............................................................................................... 19

Cleaning and care ............................................................................................... 20Housing ................................................................................................................. 20

Cleaning the drip tray ....................................................................................... 21Grease filter(s) ....................................................................................................... 21Charcoal filter ........................................................................................................ 24

Disposing of charcoal filters ............................................................................. 24Reactivatable charcoal filter ............................................................................. 24

Installation............................................................................................................ 25Before installation.................................................................................................. 25Protective foil......................................................................................................... 25Installation instructions.......................................................................................... 25Assembly parts...................................................................................................... 26Appliance dimensions ........................................................................................... 28Safety distance between hob and cooker hood (S) .............................................. 29Installation recommendations ............................................................................... 30Drilling diagram for wall mounting......................................................................... 30

Connection for air extraction ............................................................................. 31Condensate trap.................................................................................................... 32Silencer.................................................................................................................. 32

Electrical connection .......................................................................................... 34

After Sales / Warranty ......................................................................................... 35Position of the data plate ...................................................................................... 35

Contents

3

Technical data...................................................................................................... 36Note for test institutes ........................................................................................... 36

Warning and Safety instructions

4

This appliance complies with all relevant local and national safetyrequirements. Inappropriate use can, however, lead to personalinjury and damage to property.

To avoid the risk of accidents and damage to the appliance, pleaseread these instructions carefully before using it for the first time.They contain important notes on the safety, installation, use andmaintenance of the appliance. Miele cannot be held liable for non-compliance with these instructions.

Keep these instructions in a safe place and ensure that all usersare familiar with the contents. Pass them on to any future owner ofthe appliance.

Correct application

This cooker hood is intended for use in domestic households andsimilar working and residential environments.

The cooker hood is not intended for outdoor use.

It must only be used as a domestic appliance to extract vapoursand remove odours from cooking.Any other usage is not supported by the manufacturer and could bedangerous.

Where a recirculation cooker hood is fitted above a gas hob,please ensure that there is an adequate supply of fresh air into theroom in which it is installed. Please seek the advice of a qualified gasfitter (e.g. GasSafe in the UK) if necessary.


5

The cooker hood can only be used by people with reducedphysical, sensory or mental capabilities, or lack of experience andknowledge, if they are supervised whilst using it, or have beenshown how to use it in a safe way and recognise and understand theconsequences of incorrect operation.

Safety with children

Children under 8 years of age must be kept away from the cookerhood unless they are constantly supervised.

Children 8 years and older may only use the cooker hoodunsupervised if they have been shown how to use it safely andrecognise and understand the consequences of incorrect operation.

Children must not be allowed to clean or maintain the cookerhood unsupervised.

Please supervise children in the vicinity of the cooker hood and donot let them play with it.

The hob lighting is very intensive.Ensure, in particular, that babies/small children do not look at thelight.

Danger of suffocation!Whilst playing, children may become entangled in packagingmaterial (such as plastic wrapping) or pull it over their head with therisk of suffocation. Keep packaging material away from children.


6

Technical safety

Unauthorised installation, maintenance and repairs can causeconsiderable danger for the user. Installation, maintenance andrepairs must only be carried out by a Miele authorised technician.

A damaged appliance can be dangerous. Check it for visible signsof damage. Do not use a damaged appliance.

The electrical safety of this appliance can only be guaranteedwhen correctly earthed. It is essential that this standard safetyrequirement is met. If in any doubt please have the electricalinstallation tested by a qualified electrician.

Reliable and safe operation of this cooker hood can only beassured if it has been connected to the mains electricity supply.

The connection data (voltage and frequency) on the data plate ofthe cooker hood must match the mains electricity supply in order toavoid the risk of damage to the cooker hoodCompare this before connecting the appliance to the mains. Consulta qualified electrician if in any doubt.

Do not connect the appliance to the mains electricity supply by amulti-socket unit or an extension lead. These are a fire hazard anddo not guarantee the required safety of the appliance.

EXT model cooker hoods are connected to their external motorusing a special connection cable and plug connectors. These appliances may only be combined with a Miele externalmotor.


7

For safety reasons, this appliance may only be used after it hasbeen built in.

The cooker hood must not be used in a non-stationary location(e.g. on a ship).

Touching electrical components and tampering with electrical andmechanical parts is highly dangerous to the user and can causeoperational faults. Only open the housing as described in the instructions given in theinstallation sheet and in the Cleaning and care section of thisbooklet. Under no circumstances should any other parts of thehousing be opened.

The manufacturer's warranty will be invalidated if the appliance isnot repaired by a Miele approved service technician.

Miele can only guarantee the safety of the appliance whengenuine original Miele replacement parts are used. Faultycomponents must only be replaced by Miele spare parts.

If the electrical connection cable is faulty it must only be replacedby a Miele authorised service technician to protect the user fromdanger.

During installation, maintenance and repair work, the appliancemust be disconnected from the mains electricity supply.


8

Using at the same time as another heating appliance that depends on the airfrom the room

Danger of toxic fumes!Great care should be taken when using the cooker hood in thesame room or the same area of the house at the same time asanother heating appliance that depends on the air from the room.Such heating appliances draw in air from the room and ductexhaust gases out to the open air through a chimney or extractionducting. They include gas, oil, wood and coal-fired boilers andheaters, continuous flow or other water heaters, gas hobs andovens.

The cooker hood draws in air from the kitchen and fromneighbouring rooms. This applies to the following modes ofoperation:- extraction mode,- extraction mode with an external motor,- recirculation mode with a recirculation box installed outside theroom.If there is insufficient air, an underpressure will occur. The heatingappliance may be starved of oxygen. This impairs combustion.Harmful gases could be drawn from the chimney or extractionducting back into the room.Risk of death!


9

In order to ensure safe operation and to prevent gases given off bythe heating appliance from being drawn back into the room, whenthe cooker hood and the heater are both operated simultaneously,an underpressure in the room of 0.04 mbar (4 Pa) is the maximumpermissible.

Sufficient ventilation can be maintained by air inlets which cannotbe blocked, e.g. in windows, doors and outside wall vents. Thediameter of the inlet openings must enable sufficient ventilation. Aventilation brick alone is not generally sufficient to ensure safeventilation.

The overall ventilation condition of the dwelling must be taken intoaccount. If in any doubt, the advice of a competent builder, or forgas, a qualified gas fitter should be sought.

If the cooker hood is being operated in recirculation mode,whereby the air is redirected into the room in which it is installed,the above restrictions do not apply.


10

Correct use

Never use a naked flame beneath the cooker hood. To avoid thedanger of fire, do not flambé or grill over a naked flame.When switched on, the cooker hood could draw flames into the filter.Fat deposits could ignite, presenting a fire hazard.

The cooker hood can become damaged when exposed toexcessive heat.

– When using the cooker hood over a gas hob, ensure that anyburners in use are always covered by a pan. Switch the cookingzone off when a pan is removed, even for a short time.

– Select a pan which is suitable for the size of the burner.

– Regulate the flame so that it does not burn up the sides of thepan.

– Avoid overheating the pan (e.g. when cooking with a wok).

Always switch the cooker hood on when a cooking zone is in use,otherwise condensation may collect in the hood, which could causecorrosion.

Overheated oil and fat can ignite, causing fire damage to thecooker hood.When cooking with oil or fat, chip pans and deep fat fryers etc, donot leave the pans unattended. Similarly, never leave an open grillunattended when grilling.


11

Do not use the cooker hood without the filters in place. This wayyou will avoid the risk of grease and dirt getting into the applianceand hindering its smooth operation.

There is a risk of fire if the cooker hood is not cleaned asdescribed in these operating instructions.

The cooker hood can get very hot during cooking due to heatrising from the hob.Do not touch the housing or the grease filters until the cooker hoodhas cooled down.

Correct installation

Refer to the cooker or hob manufacturer's instructions as towhether a cooker hood may be operated above the cooker/hob.

Safety regulations prohibit the fitting of a cooker hood over solidfuel stoves.

An insufficient safety distance between the hob and the cookerhood can result in damage to the cooker hood.The minimum safety distances between the top of the cooker or hoband the bottom of the cooker hood given in the “Installation” sectionof this booklet must be maintained, unless the hob manufacturerstates that a greater safety distance is required.If more than one cooking appliance is fitted beneath the cookerhood, and they have different minimum safety distances to thecooker hood, select the greater distance.

The distances given in “Installation” must be observed whenfitting the cooker hood.

Metal parts can have sharp edges which may cause injury.Wear gloves to protect your hands from being cut.

Exhaust ducting must be of non-inflammable material. Suitablematerial is available from Miele specialist dealers or the Miele SparesDept.


12

The appliance must not be connected to a chimney or flue whichis in use. Neither should it be connected to ducting which ventilatesrooms with fireplaces.

If exhaust air is to be extracted into a chimney or ventilation ductno longer used for other purposes, seek professional advice.

Cleaning and care

There is a risk of fire if the cooker hood is not cleaned asdescribed in these operating instructions.

Do not use a steam cleaning appliance to clean this appliance. The steam could reach electrical components and cause a shortcircuit.

Accessories

Only use genuine original Miele accessories and spare parts withthis appliance. Using accessories or spare parts from othermanufacturers will invalidate the warranty and Miele cannot acceptliability.

Caring for the environment

13

Disposal of the packingmaterialThe packaging is designed to protectthe appliance from damage duringtransportation. The packaging materialsused are selected from materials whichare environmentally friendly for disposaland should be recycled.

Recycling the packaging reduces theuse of raw materials in themanufacturing process and alsoreduces the amount of waste in landfillsites.

Disposing of your oldapplianceElectrical and electronic appliancesoften contain valuable materials. Theyalso contain specific materials,compounds and components, whichwere essential for their correct functionand safety. These could be hazardousto human health and to the environmentif disposed of with your domestic wasteor if handled incorrectly. Please do not,therefore, dispose of your old appliancewith your household waste.

Please dispose of it at your localcommunity waste collection / recyclingcentre for electrical and electronicappliances, or contact your dealer orMiele for advice. You are alsoresponsible (by law, depending oncountry) for deleting any personal datathat may be stored on the appliancebeing disposed of. Please ensure thatyour old appliance poses no risk tochildren while being stored prior todisposal.

Guide to the appliance

14

Guide to the appliance

15

a DADC 6000 towerAvailable as an optional accessory for concealing extraction ducting to theceiling.

b Charcoal filterAccessory required for recirculation mode

c Canopy

d Hob lighting

e Controls

f Grease filter

g Exhaust socketExtraction ducting can be directed through the back of the cooker hood orupwards to the ceiling.

h Drip tray

i On/Off control for the fan

j Controls to select the fan power level

k On/Off control for the hob lighting

Modes of operation

16

Depending on the model of the cookerhood, the following options areavailable:

Extraction mode

The air is drawn in and cleaned by thegrease filter and directed outside.

Non-return flap

The non-return flap is designed toprevent the exchange of room andoutside air taking place when thecooker hood is switched off.The flap is closed when the cookerhood is switched off.When the cooker hood is switched on,the non-return flap opens for thecooking vapours to be blown directlyoutside.

If the on-site ventilation system doesnot have a non-return flap, the non-return flap supplied must be fitted in theexhaust socket in the motor unit.

Recirculation modeRecirculation mode cooker hoodsrequire charcoal filters. These areavailable as optional accessories: see“Technical Data”.

The air is drawn in and cleaned first bythe grease filter and then by a charcoalfilter. The cleaned air is thenrecirculated back into the kitchen.

Operation with an externalmotor(...EXT model cooker hoods)

Cooker hoods set up for operation withan external motor have to be connectedto a Miele external motor located in asuitable position outside the room inwhich the cooker hood is installed. Theexternal motor is linked to the cookerhood via a connection cable and thenoperated using the controls on thecooker hood.

Operation

17

Switching the fan onSwitch the fan on as soon as you startcooking. This is to ensure that vapoursare captured right from the start.

Press the On/Off control .

The fan will switch on at setting 2 andthe symbol and 2 will light up in thepower setting display.

Selecting the power levelFor light to heavy cooking vapours andodours, select from power levels 1 to 3.

For short periods of cooking food withintensive vapours and a strong aroma,e.g. when searing meat, select Boostersetting B.

Select the power level you want bypressing the or control.

Reducing power down from theBooster setting

If power management is activated(default setting), the fan automaticallyswitches back to level 3 after 5 minutes.

Run-on time It is advisable to run the fan for a few

minutes after cooking has finished.

This helps to remove any lingeringvapours and odours from the air.

It also reduces the risk of residuesaccumulating in the cooker hood andany resultant odours.

Switching the fan off Press the On/Off control to switch

the fan off.

The symbol will go out.

Switching the hob lighting on/offThe hob lighting can be switched onand off independently of the fan.

To do so press the lighting control .

The symbol will light up when thehob lighting is switched on.

Power managementThe cooker hood features a powermanagement system to help saveenergy. The fan power level is reducedand the lighting is switched offautomatically.

– If the Booster setting has beenselected, the fan will automaticallyswitch to level 3 after 5 minutes.

– From levels 3, 2 or 1 the power willbe reduced by one level after 2 hoursand then in 30 minutes stages untilthe fan finally switches off.

– The hob lighting will switch offautomatically after 12 hours.

Operation

18

Switching Power management on/off

You can deactivate Powermanagement.This can result in increased electricityconsumption.

To set this option, both the fan andthe hob lighting must be switched off.

Press the “” and “” controls at thesame time for approx. 10 seconds,until the 1 lights up.

Then press in turn,

– the lighting control ,

– the “” button and then

– the lighting control again.

If Power management is switched on,the 1 and B indicators will light upconstantly.If it is switched off, 1 and B will flash.

Press “” to switch Powermanagement off.

The 1 and B indicators will flash.

To switch it on, press “”.

The 1 and B indicators will light upconstantly.

Confirm your choice with the On/Offcontrol .

All the indicator lamps will go out.

If you do not confirm within 4 minutes,the cooker hood will revert to the oldsetting.

Safety switch-offIf Power management has beendeactivated, the cooker hood willswitch itself off automatically after12 hours if it has been left on (fan andhob lighting).

To switch it on again press the On/Off control or the lightingcontrol .

Energy saving tips

19

This cooker hood operates veryefficiently and economically. Thefollowing will help you to save evenmore energy when using it:

– Ensure that there is sufficientventilation in the kitchen whencooking. In extraction mode, if thereis insufficient air flow the cookerhood cannot operate efficiently andthis causes increased operating noiselevels.

– Always cook with the lowest possiblesetting. This produces fewer cookingvapours, so you can use a lowercooker hood power level andtherefore benefit from reducedenergy consumption.

– Check the power level selected onthe cooker hood. A lower power levelis generally sufficient for the majorityof cooking. Only use the Boostersetting when necessary.

– When a large volume of cookingvapours is being produced, switch toa high power level in good time. Thisis more efficient than operating thecooker hood for longer to try tocapture cooking vapours which havealready been distributed throughoutthe kitchen.

– Make sure that you switch the cookerhood off after use.

– Clean or change the filters at regularintervals. Heavily soiled filters reduceperformance, increase the risk of fireand are unhygienic.

Cleaning and care

20

Before proceeding with anymaintenance or cleaning task, thecooker hood must be disconnectedfrom the power supply, see “Warningand safety instructions”.

Housing

General information

The surfaces and controls aresusceptible to scratches andabrasion.Please observe the followingcleaning instructions.

All external surfaces and controls canbe cleaned using hot water with asmall amount of washing-up liquidapplied with a well wrung-out softsponge or cloth.

Make sure that water does notget into the cooker hood.Only clean the area of the controlswith a damp cloth.

Then wipe the surfaces dry using asoft cloth.

Do not use:

– cleaning agents containing soda,acids, chlorides or solvents,

– abrasive cleaning agents, e.g.powder cleaners or cream cleanersand abrasive sponges, as well as potscourers or sponges which havebeen used previously with abrasivecleaning agents.

Important for appliances withstainless steel surfaces

(This information does not apply to thecontrols).

Stainless steel surfaces can becleaned with a proprietary non-abrasive cleaning agent designedspecifically for use on stainless steel.

To help prevent re-soiling, aproprietary conditioning agent forstainless steel (available from Miele)can also be used.Apply sparingly with a soft cloth.

Important for the controls

Do not leave soiling on the controlsfor any length of time.Otherwise they may sufferdiscolouration or damage.Remove soiling straight away.

Please observe the general notes oncleaning earlier in this section.

Do not use stainless steel cleaningagents on the controls.

Cleaning and care

21

Important for appliances with glasssurfaces

Glass surfaces can be cleaned usinga proprietary non-abrasive cleaningagent designed specifically for use onglass.

Cleaning the drip tray

Condensate collects in the drip trayunderneath the grease filter. This traycan be removed for cleaning.

Pull the drip tray forwards a little, andthen pull it downwards to remove it.Pour any condensate that hascollected in it away and then cleanthe tray with a damp cloth.

Grease filter(s)The re-usable metal grease filter(s) inthe appliance remove solid particlesfrom the kitchen vapours (grease, dust,etc) preventing soiling of the cookerhood.

The grease filter(s) must be cleaned atregular intervals.

A heavily soiled grease filter hindersair extraction and will lead toincreased levels of soiling in thecooker hood and in the kitchen.

Fire hazard!An oversaturated grease filter is a firehazard.Clean the grease filter(s) at regularintervals.

Cleaning interval

Accumulated grease solidifies over alonger period of time and makescleaning more difficult. The greasefilter(s) should therefore be cleaned atleast every 3 to 4 weeks.

Cleaning and care

22

Removing a grease filter

When handling a grease filter, becareful not to drop it.This can result in damage to the filterand the hob below.Make sure you hold the filter securelyat all times when handling it.

Pull the grease filter carefully out ofits mountings along the bottom edge.Then pull it towards you a little whilstpressing it in at the top. It can then betaken downwards to remove it.

Cleaning the grease filter by hand

Clean the filter with a soft nylon brushin a mild solution of hot water and asmall amount of washing-up liquid.Do not use “neat” washing up liquid.

Unsuitable cleaning agents

Unsuitable cleaning agents can causedamage to the surface of the filters ifused regularly.Do not use:

– cleaning agents containing descalingagents

– powder cleaners, cream cleaners

– aggressive multi-purpose cleaningagents or spray cleaners for grease

– oven sprays

Cleaning the grease filter in adishwasher

Place the grease filter upright orslightly inclined in the lower basket.Ensure the spray arm is notobstructed.

Use a commercially availablehousehold dishwasher detergent.

Select a dishwasher programme witha wash temperature between 50 °Cand 65 °C.

Depending on the detergent used,cleaning the grease filter in adishwasher can cause permanentdiscolouration to the internal surfacesof the filter. However, this will notaffect the functioning of the greasefilter in any way.

Cleaning and care

23

After cleaning

After cleaning, leave the filter to dryon an absorbent surface beforereplacing it.

When removing the filter for cleaning,also clean off any residues of oil or fatfrom the now accessible casing toprevent the risk of these catching fire.

First fit the top of the grease filter intothe slots at the top, then swing thebottom of the grease filter into placeand press it into position.

Cleaning and care

24

Charcoal filterRecirculation cooker hoods must befitted with a charcoal filter in addition tothe grease filter. This is designed toabsorb cooking odours.It is fitted in the top of the cooker hood.

Fitting/replacing charcoal filters

Take the charcoal filter out of itspackaging.

Fit the charcoal filter into the holder inthe top of the cooker hood.

When to change the charcoal filter

Replace the charcoal filter when it nolonger absorbs kitchen odourseffectively.It should, however, be replaced atleast every 6 months.

Disposing of charcoal filters

Used charcoal filters can be disposedof with the normal household waste.

Reactivatable charcoal filter

A reactivatable charcoal filter isavailable for this cooker hood. Byreactivating it in an oven it can bereused several times.

It is supplied with its own installationand usage instructions which mustbe observed.

Charcoal filters are available to order viathe Miele Webshop, the Miele SpareParts Department (see end of thisbooklet for contact details) or from yourMiele dealer.

The charcoal filters are listed under“Technical data” at the back of thisbooklet.

Installation

25

Before installation

Before installation, it is importantto read the information given on thefollowing pages as well as the“Warning and Safety instructions” atthe beginning of this booklet.

Protective foilThe housing components haveprotective foil around them to protectthem from transport damage.

Please remove this foil before fittingthe housing components. It can bepeeled off easily.

Installation instructionsSee enclosed Installation sheet forinstructions on how to install thisappliance.

Installation

26

Assembly parts

Installation

27

a 1 exhaust connectionfor exhaust ducting 150 mm

b 1 reducing collarfor exhaust ducting 125 mm

c 1 non-return flapfor installation in the exhaust socketof the fan motor (not for recirculationmode). The non-return flap mayalready be fitted depending onmodel.

d Cover foilfor use when changing extractionducting direction

e Wall bracketfor securing the cooker hood to thewall

5 screws 5 x 60 mm and5 plugs 8 x 50 mm3 washers 6.4 mmfor securing to the wall.

The screws and plugs aredesigned for use in solid walls only.For other types of wall construction,alternative fixings will be required.Make sure the wall is able to take theweight of the cooker hood.

Montage

Installation

Montaje

M

ontaggio

Montering

Montagem

A

sennus

Installation instructions

Installation

28

Appliance dimensions

The drawing is not to scale.

Installation

29

a Extraction ducting upwards or to the rear.

b Cut-out for cooker hoods with hard-wired connection rather than a plug.

c 200 mm cut-out ensures sufficient space through the wall for the extractionducting to flex.

d Ventilation grille for recirculation mode. The distance to the ceiling or tofurniture installed above the appliance should be at least 300 mm.

Connection for air extraction 150 mm, or 125 mm with reducing collar.

Please observe installation positions for the socket and for the ducting outletshown on the relevant drawings when using the DADC 6000 tower.

Safety distance between hob and cooker hood (S)

When planning the installation height of your cooker hood, the minimum safetydistance between the top of a cooker or hob and the bottom of the cooker hoodis as follows, unless a greater distance is specified by the manufacturer of yourcooking appliance.See “Warning and Safety” instructions for further information.

Cooking appliance Minimum distance S

Electric hob 450 mm

Electric grill, deep fat fryer (electric) 650 mm

Multi-burner gas hob, total output ≤ 12.6 kW, no burner > 4.5 kW

650 mm

Multi-burner gas hob,total output > 12.6 kW and ≤ 21.6 kW, no burner > 4.8 kW.

760 mm

Multi-burner gas hob,total output > 21.6 kW, or multi-burner gas hob where one burner > 4.8 kW.

Not possible

Single burner gas hob, output ≤ 6 kW. 650 mm

Single burner gas hob, output > 6 kW and ≤ 8.1 kW. 760 mm

Single burner gas hob, output > 8.1 kW Not possible

Installation

30

Installation recommendations– Account should also be taken of the

height of the person who will beusing the hood most often. Theyshould have sufficient space to workcomfortably at the hob, and be ableto reach the cooker hood controlswith ease.

– Please be aware that if positioned toohigh, extraction will be inefficient.

– To achieve optimum vapourextraction, the cooker hood must bepositioned centrally over the hob, notto the side.

– The hob should be no wider than thecooker hood, and if possible, itshould be narrower.

– The installation area must be easilyaccessible. The cooker hood shouldbe easily accessible and easy todismantle in the event that service isrequired. This should be taken intoconsideration when planning theposition of cupboards, shelves,ceilings or features in the vicinity ofthe cooker hood.

Drilling diagram for wallmounting When drilling, please follow the

directions contained on theaccompanying installation sheet.

When installing a custom back wallwith pre-drilled holes, please refer tothe drilling distances in the drawingabove (screws 5 mm).

Connection for air extraction

31

If the cooker hood is used at thesame time as a heating appliancethat relies on oxygen from the sameroom, there is a risk in certaincircumstances of toxic fumesbuilding up.It is essential that the “Warning andSafety” instructions are observed.The cooker hood should be installedaccording to local and nationalbuilding regulations. Seek approvalfrom the building inspector wherenecessary.

Use smooth pipes or flexible ductingmade from approved non-flammablematerials for exhaust ducting.

When using an external motor, makesure that the exhaust ducting issufficiently rigid. The external motorcan cause an underpressure whichcan result in the exhaust ductingdistorting.

To achieve the most efficient airextraction with the lowest noise levels,please note the following:

– The diameter of the exhaust ductingshould not be less than 150 mm.

– If flat ducting is being used, the crosssection must not be smaller than thecross sectional area of the exhaustconnection.

– The exhaust ducting should be asshort and straight as possible.

– Only use wide radius bends.

– The exhaust ducting must not bekinked or compressed.

– Ensure that all connections arestrong and airtight.

Remember that any constriction ofthe air flow will reduce extractionperformance and increase operatingnoise.

If the exhaust is ducted through anoutside wall, a telescopic wall vent ora roof vent (available as an optionalaccessory) is recommended.

If the exhaust air is to be ducted intoa flue, the ducting must be directed inthe flow direction of the flue.

Where ducting is horizontal, it mustbe laid to slope away at at least 1 cmper metre. This is to ensure thatcondensate cannot drain back intothe cooker hood.

If the exhaust ducting is to runthrough rooms, ceiling space etc.there may be great variations intemperature between the differentareas. The problem of condensationwill need to be addressed. Theexhaust ducting will need to besuitably insulated.


32

Condensate trap

In addition to insulating the exhaustducting, we recommend that a suitablecondensate trap is also installed tocollect and evaporate any condensatewhich may occur.Condensate traps for 125 mm or150 mm ducting are available asoptional accessories.

A condensate trap can only be fitted inextraction ducting which is directedupwards out of the cooker hood.

When installing a condensate trap,ensure that it is positioned verticallyand as closely as possible above theexhaust socket.The arrow on the housing indicatesthe direction of air-flow.

A condensate trap is integrated incooker hoods which are designed forconnection to an external motor(model......EXT).

Silencer

To achieve even further reductions innoise levels, a special silencer (optionalaccessory) can be fitted in the ductingsystem.

Extraction mode

The silencer not only reduces noisefrom the motor outside the house, butalso sounds from outside (e.g. trafficnoise). For this reason the silencer mustbe positioned as close as possible tothe ducting exit .


33

Extraction mode with external motor

To minimise noise from the motor in thekitchen, the silencer should bepositioned in front of the external motor if possible, or, if the ducting is long,above the exhaust socket on the cookerhood . In the case of an externalmotor located inside the house, fitting asilencer behind the external motor reduces the noise of the motor outsidethe house.

Electrical connection

34

Installation, repairs and otherwork by unqualified persons couldbe dangerous. The manufacturercannot be held liable forunauthorised work.All electrical work should beundertaken by a suitably qualifiedand competent person in strictaccordance with current national andlocal safety and building regulations.

This cooker hood must only beconnected to a properly installedelectrical circuit.The electrical installation must complywith national regulations (BS 7671 inthe UK).

For extra safety, it is advisable toprotect the appliance with a suitableresidual current device (RCD) with a triprange of 30 mA (DIN VDE 0664).

It is advisable to connect this appliancevia a suitable plug and socket to makeit easy to disconnect for servicingpurposes. The socket and switch mustbe easily accessible after the appliancehas been installed.

Alternatively it can be hard-wired.

If the mains socket and switch are notaccessible after the appliance has beeninstalled, or if it is hard-wired, aseparator for each terminal must bepresent. There must be an all-polecontact gap of at least 3 mm in theswitch.This includes the switch, fuses andrelays (in accordance with EN 60335).

The connection data is given on thedata plate (See “After sales service”).Ensure that this data matches thevoltage and frequency of the householdmains supply.

After Sales / Warranty

35

In the event of a fault which you cannotremedy yourself, please contact yourMiele dealer or the Miele ServiceDepartment.

Contact details for Miele are given atthe end of this booklet. N.B. A call-outfee will be charged for service visitswhere the problem could have beenresolved as described in theseinstructions.

When contacting your dealer or Miele,please quote the model and serialnumber of your appliance.These are shown on the data plate.

Position of the data plateThe data plate is visible after removingthe grease filter.

Warranty: U.K.In the U.K., the appliance warranty isvalid for 2 years from the date ofpurchase. However, you must activateyour cover by calling 0330 160 6640 orregistering online at www.miele.co.uk.

Please note that telephone calls maybe monitored and recorded for trainingpurposes.

Warranty: Other countriesFor information on the appliancewarranty specific to your country pleasecontact Miele. See end of this bookletfor contact details.

Technical data

36

Fan motor* 200 W

Hob lighting 2 x 4.5 W

Total connected load* 209 W

Voltage AC 230 V

Fuse rating 5 A

Mains connection cable length 1.5 m

Weight

DA 6066 W 17 kg

DA 6086 W 19 kg

DA 6096 W 20 kg

DA 6096 W EXT 17 kg

* For EXT models, the connected load will depend on the type of external motor fitted.Length of connection cable to external motor: 1.9 m

Accessories required for recirculation mode

Charcoal filter DKF 25-1 or DKF 25-R (reactivatable).

Note for test institutesAll information required regarding measuring noise levels is given in the “Testingfor sound emissions” leaflet. The latest version of this leaflet can be ordered by email from:

– [email protected]

Please quote your postal address, as well as the model and serial number of yourcooker hood (see data plate).

Note for test institutes

Data quoted in the following data sheets was calculated in accordance with thefollowing standards EN 61591 and EN 60704-3. The distance between the areabeing measured/hob and the underside of the cooker hood is 450 mm and thevoltage 230 V for test purposes. Testing is carried out with a non-return valve.

Technical data

37

Data sheet for household cooker hoodsIn acc. with delegated regulation (EU) No. 65/2014 and regulation (EU) No.66/2014

MIELE

Model name/identifier DA 6066 W

Annual Energy Consumption (AEChood) 70,4 kWh/year

Energy efficiency class B

Energy efficiency index (EEIhood) 68,5

Fluid Dynamic Efficiency (FDEhood) 23,2

Fluid Dynamic Efficiency class

A (most efficient) to G (least efficient) B

Lighting Efficiency (LEhood) 58,3 lx/W

Lighting Efficiency class

A (most efficient) to G (least efficient) A

Grease Filtering Efficiency 92,4%

Grease Filtering Efficiency class


Airflow at best efficiency point 357,7 m3/h

Air flow (min. speed) 200 m3/h

Air flow (max. speed) 400 m3/h

Air flow (intensive or boost setting) 650 m3/h

Max. air flow (Qmax) 650 m3/h

Air pressure at best efficiency point 350 Pa

Airborne acoustical A-weighted sound power emissions (min. speed) 40 dB

Airborne acoustical A-weighted sound power emissions (max. speed) 54 dB

Airborne acoustical A-weighted sound power emissions (intensive orboost setting)

66 dB

Electrical power input at best efficiency point 150,0 W

Power consumption in off mode (Po) W

Power consumption in standby mode (Ps) 0,20 W

Nominal power of lighting system 9,0 W

Average illumination of the lighting system on the cooking surface 525 Ix

Time increase factor 1,2

Technical data

38


MIELE























66 dB







Technical data

39


MIELE























66 dB







Technical data

40


MIELE

Model name/identifier DA 6096 W EXT


Energy efficiency class A++


Fluid Dynamic Efficiency (FDEhood)


A (most efficient) to G (least efficient) -




Grease Filtering Efficiency %


A (most efficient) to G (least efficient) -

Airflow at best efficiency point m3/h

Air flow (min. speed) m3/h

Air flow (max. speed) m3/h

Air flow (intensive or boost setting) m3/h

Max. air flow (Qmax) m3/h

Air pressure at best efficiency point Pa

Airborne acoustical A-weighted sound power emissions (min. speed) dB



dB

Electrical power input at best efficiency point W





Time increase factor

United KingdomMiele Co. Ltd.Fairacres, Marcham RoadAbingdon, Oxon, OX14 1TWTel: 0330 160 6600Internet: www.miele.com

AustraliaMiele Australia Pty. Ltd.ACN 005 635 398ABN 96 005 635 3981 Gilbert Park DriveKnoxfield, VIC 3180Tel: 1300 464 353Internet: www.miele.com.au

Miele (Shanghai) Trading Ltd.1-3 Floor, No. 82 Shi Men Yi RoadJing' an District200040 Shanghai, PRCTel: +86 21 6157 3500Fax: +86 21 6157 3511E-mail: [email protected],Internet: www.miele.cn

China

41/F - 4101, Manhattan Place23 Wang Tai RoadKowloon Bay, Hong KongTel: (852) 2610 1025Fax: (852) 3579 1404Email:[email protected]: www.miele.hk

Miele (Hong Kong) Limited

Miele India Pvt. Ltd.Ground FloorCopia Corporate SuitesPlot No. 9, JasolaNew Delhi - 110025Tel: 011-46 900 000Fax: 011-46 900 001E-mail: [email protected]: www.miele.in

India

Miele Ireland Ltd.2024 Bianconi AvenueCitywest Business CampusDublin 24Tel: (01) 461 07 10Fax: (01) 461 07 97E-Mail: [email protected]: www.miele.ie

Ireland

MalaysiaMiele Sdn BhdSuite 12-2, Level 12Menara Sapura KencanaPetroleumSolaris Dutamas No. 1Jalan Dutamas 150480 Kuala Lumpur, MalaysiaPhone: +603-6209-0288Fax: +603-6205-3768

Miele New Zealand LimitedIRD 98 463 631Level 2, 10 College HillFreemans Bay, Auckland 1011New ZealandTel: 0800 464 353Internet: www.miele.co.nz

New Zealand

Miele Pte. Ltd.163 Penang Road# 04 - 03 Winsland House IISingapore 238463Tel: +65 6735 1191Fax: +65 6735 1161E-Mail: [email protected]: www.miele.sg

Singapore

Miele (Pty) Ltd63 Peter Place, Bryanston 2194P.O. Box 69434, Bryanston 2021Tel: (011) 875 9000Fax: (011) 875 9035E-mail: [email protected]: www.miele.co.za

South Africa

Miele Appliances Ltd.Gold & Diamond ParkOffice No. 6-217Sheikh Zayed RoadP.O. Box 11 47 82 - DubaiTel. +971 4 3044 999Fax. +971 4 3418 852800-MIELE (64353)E-Mail: [email protected]: www.miele.ae

United Arab Emirates

Manufacturer: Miele & Cie. KG, Carl-Miele-Straße 29, 33332 Gütersloh, Germany

K.E. & Kingstone Co., Ltd.6th Fl., No. 120, Sec. 2Jianguo N. Rd.Taipei, TaiwanTEL: +886 2 2502-7256FAX: +886 2 2502-3077E-mail: [email protected]:www.kenk.com.tw/ke/miele

Taiwan

ThailandBHIRAJ TOWER at EmQuartier43rd Floor Unit 4301-4303 689 Sukhumvit RoadNorth Klongton Sub-DistrictVadhana DistrictBangkok 10110, Thailand

M.-Nr. 10 639 810 / 03en-GB

DA 6066 W,DA 6086 W,DA 6096 W,DA 6096 W EXT

Documents

Operating and installation instructions Cooker hood€¦ · Compare this before connecting the appliance to the mains. Consult a qualified electrician if in any doubt. Do not connect