one wireone rig upone crew

Slick-E-Line offers the ability to perform traditional slickline operations as well as offering real time depth control, push button tool activation with verification, PLUS conventional PL data collection.

Single crew flights - single crew beds - one single crew for slickline and logging operations.

Hybrid technology is the future of well intervention and ‘smart’ slickline is the key.

www.paradigm.eu

Slick-E-Line System

ParaWire

Cable head

ParaSheave

ParaLogParaComm Antenna

ParaWinch

Slick-E-Line surface equipment comprises a surface powered RxTx-comms module, electrically connected to a close-coupled antenna, orientated parallel to the Slick-E-Line for optimum antenna directivity and gain. This wirelessly picks up the downhole logging tool signals from the ParaComm Antenna and communicates with the downhole tool when in transmit mode.

Slick-E-Line real-time depth correlation capabilities confirm operations are on depth and provide the exact position of the downhole tool at all times. This continuous depth correlation means that slickline operations can now be adapted in real time, and that the success of the job can be confirmed before pulling out of hole.

Slick-E-Line mechanical services enhance the quality and operational safety of traditional mechanical operations with its added accurate depth measurement and monitoring of downhole tool and environment status in real time.

Slick-E-Line supported perforation, tubing punch, and cutting for pipe recovery - on depth, and in real time.

Slick-E-Line run real-time production logs across a range of wellbore environments.

ParaWinchSpecifications

Weight with full drums approximately 8000 kg.

The winch is modular.

Both winch boxes with the drum can be removed easily reducing the weight by approximately 3 tonnes.

Dimensions: 3.6 x 1.6 x 2.9 m (LWH)

The winch is designed to handle the following cables/wires:• 0.125 standard slick line• 0.160 standard slick line • 0.160 Slick-E-Line• 7/32 heavy duty fishing

Operating

The winch has a control panel that is intuitive to use.

Different control modes are available:• Rig up remote (from the rig floor the winch can be

operated safely)• Remote control by ethernet from logging computer and/

or remote location• Standard manual control• Constant speed with speed range between 0.2 and

1200 ft/min (0.05 and 400 m/min)• Automatic logging mode (running (semi) automatic

logging passes)• Constant tension mode

Full electric, easy to operate, silent and very low maintenance.

www.paradigm.eu

Dimensions Typical

Core diameter 0.125“

Coating thickness 0.0175”

Slick-E-Line diameter 0.160”

Diameter tolerance 0.002”

Ovality < 0.5 %

Standard lengths 25 & 30 kft

No. of Jobs 600 jobs

Safe working load max. 1,400 lbs

Line stretch 36 inch/kft/klbs

Sheave wheel diameter min. 20”

Design working Pressure 5,000 psi

Max. working Pressure 10,000 psi

Pay off / take up speed 50/max. 166 m/min

Property StandardApplicable

Typical

Mechanical

Breaking load EN 10 204 3.1 2490 lbs

Total weight EN 10 204 3.1 47.26 lbs/kft

Adhesion Norsok M-710-4API 17i 2008

> 220 lbs

Impact strength Norsok M-710-4API 17i 2008ISO 6272

> 6” (2.20 lbs falling weight)

Wear resistance Norsok M-710-4ISO 6722ISO6931-1

> 600 jobs

Coating Integrity (voids) Norsok M-710-4HSE rr485

< 0.00004”

Chemical

Crude oil swelling Norsok M-710-4Norsok M-710-8ISO 15156-1API 17j2008ISO15156

1%

Compatibility with brine, H2S, CH4 & methanol

-

Thermal

Continuous usage temp. Norsok M-710-4HSE rr485Norsok D-002

300°F

Short term usage temp. 500°F

Min. usage temp. -40°F

Environmental

RGD N2, CO2 Norsok M-710-4HSE rr485

-

UV resistance gi_i-4-3_eNorsok M-710-4Norsok M-710-8ISO 15156-1API 17i2008ISO15156

No change in properties

ESCR none

Electrical

Di-electric strength API 17i 2008 1,000 V

ParaWire is a polymeric precision coated alloy slickline. The formulated polymeric coating combines superior abrasion and corrosion resistance with electrical insulation, enabling at the same time normal mechanical slickline operations AND two-way data communication with a battery powered downhole tool string.

ParaWire is deployed using standard pressure control equipment combined to best effect with the ParaWinch technology.

ParaWire is made using a proprietary coating process developed by Paradigm and is the only one of its type in the world.

ParaWire

ParaLog

The difference between ParaLog and other conventional acquisition systems is the radically different communications architecture.

Whilst most real time systems log in the depth domain (tools need to be moving to acquire data versus depth) and all memory systems log in the time domain (but have to be merged to depth versus time at surface post-log), the Slick E-line system logs everything in the time domain… including depth!

Features:

Simple and easy interface• One phase, instead of multiple phases: As soon as the

program is launched, it’s acquiring.• Time based plot at the bottom: As soon as the tool is on,

data is being received. All data Including depth.• Ready to be selected and output to API.

Real time data acquisition and plotting• Constant data stream, adapting data rate to

conditions: ParaLog constantly receives data as fast as conditions allow.

• Programmable sampling rates: Maximise the bandwidth. If some curves are not needed at the highest sample rate, sample less.

A unique, flexible and user friendly acquisition software.

• Dynamic data buffer indication: On any API plot, ParaLog outputs in the depth track two tool string representations.

• The tool can move faster than the data transmission allows, and if acquiring at the highest sampling rate this does not dictate the logging speed.

Data selection from time based plotThe default ParaLog interface is a time based presentation, from which single or multiple passes can be selected and output to single or multiple API presentations. All the data is available at any given moment, even when the engineer was “not logging”.

• Multiple data selections to output: Just select in the time plot and send to API.

• Easy output and merging to any API (or multiple) presentation(s).

• Importing reference logs (correlation) done in the same easy manner.

• Automatic pass labelling by default: Down/up passes and stations are labelled as such by default. Easier to pick and rename.

Easy data manipulation and presentation on API log• ParaLog makes acquisition much more flexible and

simple.• Depth matching made easy – just drag the dataset to

match the (imported) reference log and all data from that pass is put on depth, with visual feedback that the correct depth offset has been applied.

• Drag and drop formats: Editing formats made easy, just drag, drop, click, stretch, etc, all visual.

• Exporting PL data on depth has never been easier, just select all passes, output to an API log and click and drag to visually match them to the correlation log. All of them. All of the passes will include the resulting depth offset and from there: Export data to LAS.

• Importantly, ALL RAW data is also available in the dataset, without any of the above manipulations making it easy to revert back to the original if required.

www.paradigm.eu

LoggingThe basic Slick-E-Line logging tool string comprises a simple logging head and electronic cartridge connected to a translator module above a memory PLT. The various sensors communicate in MODBUS with the central controller (located in the top of the tool string) which, as well as logging all sensor data to the memory in the cartridge, sends the data through the Slick-E-Line wire. All data is recoded and stored downhole at the highest sampling rate, and sent to surface at a reduced rate for real-time plotting purposes. At the end of the slickline logging run, the data from the downhole memory can be downloaded and merged with the surface data to restore it to its full resolution in industry standard format.

The basic tool string module is configured to mechanically and electrically interface with third party tool string components e.g. Hunter RBT, MFC and PLT to allow users maximum flexibility and choice.

SlicklineIn addition to mechanical operations, ruggedised Gamma/CCL tools capable of withstanding normal jarring shock loads can be run below the cable head in cases where depth correlation and tool verification are required.

The futureWorking on an open system basis with logging tool suppliers should allow new exciting tools to be developed by a range of companies which can all be run on the Slick-E-Line or even be Slick-E-Line specific.

Downhole Components

Technology Building Blocks

ParaControlThe new Control system built into the ParaWinch is the latest in Human Machine Interface (HMI) technology. Ergonomically superior to traditional systems it’s indicative of Paradigm’s bottom up approach to the Slick-E-Line technology. Designed to match the infinite controllability of the direct electric drive system the ParaControl system offers both the necessary manual controls and contains all relevant data (depth, tension, logging speeds etc) in one easy to read display system.

ParaSheaveThe ParaSheave intelligent depth and tension system allows the winch operator to receive the depth and tension information from the sensors in the sheaves wirelessly. Traditional hydraulic weight indicators require heavy cumbersome hydraulic lines and are notoriously inaccurate over time. In addition, in order to minimise slippage at the traditional counter head, the wire is normally wrapped at the counter head. With a coated wire this is undesirable if coating life is to be optimised so again Paradigm have drilled down to the heart of the problem. The ParaWinch has a wire guide for spooling but no traditional counter head assembly. The ParaSheaves each have two sensors giving a system with 400% redundancy and the ability to cross calibrate between the sheaves.

ParaComm AntennaParaComm Antenna seals on the coated wireline cable against well pressure. The patented sealing element is designed with a large cross sectional area which provides this environment friendly seal and cleaning action during well interventions. The depth and tension measurements are gathered from a pickup on the pressure control equipment and sent to the unit via Wi-Fi. The pressure control equipment is pressure sensitive and automated and will react when an increase in wellhead pressure is identified.

www.paradigm.eu

Paradigm GeoKey Services specialises in providing cased hole services to the oil and gas industry in the North Sea and abroad.

Our specialist services include tubing conveyed perforating, memory cased hole logging, pipe recovery and very soon we will add Slick-E-Line services to our repertoire. To date Paradigm GeoKey Services is proud to have supplied our products and services to companies such as Shell, BP, Marathon, Apache, Talisman, TAQA, Heritage and as well as several other well-known and respected oil and gas operators. With a strong track record for safe, reliable, quality service delivery we can now also offer the cutting edge of well intervention technology.

Slick-E-Line OperationsThe Slick-E-Line platform provides it users with a complete offering of cased hole services. Key products and features are as follows;

Real time logging• Correlation - Gamma-Ray CCL• Measurement - Pressure/temperature,

production and pulse neutron logging• Integrity - Cement or radial bond logging,

multi finger caliper and leak detection • Pipe recovery - Free point• Precise logging speeds from two feet per

minute for improved log quality

Real time ballistics• Hollow steel carrier and thru tubing gun

system perforating• Plugs, packers, retainers and gauge

hanger setting• Dump bailers• Cutters and back off shots

Intelligent slickline services• Real time depth• Real time orientation for gas lift valve

change out• Real time intelligent jarring• Real time intelligent drift - GR-CCL/

pressure/temperature/X-Y caliper

Logging Equipment

www.paradigm.eu © Paradigm GeoKey Services Ltd. All rights reserved.

The Slick-E-Line platform is being developed to support several manufacturers of cased hole logging equipment. Initially the Slick-E-Line logging platform will support tools manufactured by Altos Technologies and Hunter Well Sciences. Soon to follow these two suppliers will be Sondex and Probe Technologies. Slick-E-Line users will be capable of utilising their invested capital to the full deploying the appropriate translator module for their chosen brand of tool suppliers.

Training SupportParadigm GeoKey will supply training to third party well services companies for all Slick-E-Line equipment and technologies. This training can be provided at the customers facilities, on site, or at Paradigm GeoKey’s Aberdeen facilities. Training will include operation and basic maintenance of the Slick-E-Line winch, ParaSheave wireless depth and tension system and ParaLog software. Trained instructors are available to travel globally to support your operations.

Patents - Please note that much of the technology shown is patented or has patent pending status.

Paradigm GeoKey will provide training and operational support but can also call on the full technical back-up of Paradigm Technology Services in the Netherlands. As the inventors and manufacturers of all aspects of the system this is a unique level of technical capability which does not rely on any third party expertise and is available 24/7.