Bulletin 014 Rev. GOJc;CD--Model F1FR56 Series

Quick ResponseStandard Spray

Model F1 FR56 Sprinkler TypesStandard UprightStandard PendentConventionalVertical SidewallHorizontal Sidewall

Model F1 FR56 Recessed Sprinkler Types•••••• Standard Pendent/F1/F2/FP

Horizontal Sidewall I

Model F1 FR56 Concealed Sprinkler TypesStandard Pendent

Listing & Approvals1. Underwriters Laboratories Inc. and Certified for

Canada (cULus).2. Factory Mutual Approvals (FM)3. Loss Prevention Council (LPCB, UK)4. VdS SchadenverhOtung GmbH

Conventional Horizontal Sidewall

UL Listing CategorySprinklers, Automatic & Open (VNIV)Quick Response Sprinkler

Product DescriptionReliable Models F1FR56 Series Sprinklers are quick re-

sponse sprinklers which combine the durability of a stan-dard sprinkler with the attractive low profile of a decorativesprinkler.

The Models F1FR56 Series Recessed automatic sprin-klers utilize a 3.0 mm frangible glass bulb. These sprin-klers have demonstrated response times in laboratory testswhich are five to ten times faster than standard responsesprinklers. This quick response enables the Model F1FR56Series sprinklers to apply water to a fire much faster thanstandard sprinklers of the same temperature rating.

The glass bulb consists of an accurately controlled amountof special fluid hermetically sealed inside a precisely manu-factured glass capsule. This glass bulb is specially con-structed to provide fast thermal response.

At normal temperatures, the glass bulb contains the fluidin both the liquid and vapor phases. The vapor phase canbe seen as a small bubble. As heat is applied, the liquidexpands, forcing the bubble smaller and smaller as the liq-uid pressure increases. Continued heating forces the liquidto push out against the bulb, causing the glass to shatter,opening the waterway and allowing the deflector to distrib-ute the discharging water.

RecessedHorizontal Sidewall

RecessedPendent/FP

ConcealedPendent

ApplicationQuick response sprinklers are used in fixed fire protec-

tion systems: Wet, Dry, Deluge or Preaction. Care must beexercised that the orifice size, temperature rating, deflec-tor style and sprinkler type are in accordance with the lat-est published standards of the National Fire Protection As-sociation or the approving Authority Having Jurisdiction.Quick response sprinklers are intended for installation asspecified in NFPA 13. Quick response sprinklers and stan-dard response sprinklers should not be intermixed.

The Reliable Automatic Sprinkler Co., Inc., 103 Fairview Park Drive, Elmsford, New York 10523

Model F1 FR56 Quick Response Upright, Pendent & Conventional SprinklersInstallation Wrench: Model D Sprinkler WrenchInstallation Data:

Nominal Thread Nominal K Factor Sprinkler ApprovalSprinkler Identification Number

(SIN)Orifice Size

IHeight Organization

IUS Metric Upright Pendent

Standard-Upright (SSU) and pendent Deflectors Marked to Indicate Position

Y2" (15mm) %" NPT(R%) 5.6 I 80 2.25" (57mm) 1,2,3,4 RA1425(1) I RA 1414 (1)(2)

Conventional-Install in Upright or Pendent Position

15mm(1) Y2" NPT(R%) 5.6 I 80 57mm 3,4 RA1475

(1)cULus listed corrosion resistant (Polyester coated) sprinkler.(2)Polyester coated FM approved sprinkler.

Upright Pendent

Model F1 FR56 Quick Response Recessed Pendent SprinklerInstallation Wrench: Model GFR2 Sprinkler WrenchInstallation Data:

Nominal Thread K Factor Sprinkler Sprinkler Identification NumberOrifice Size US Metric Height (SIN)

%" (15mm) Y2" NPT(R%) 5.6 80 2.25" (57mm) RA1414

(1) Refer to escutcheon data table for approvals and dimensions.

2 1/4 R HOLE DIA.

{57.2mmJ

TURN COLLARUNTIL TIGHTAGAINST SPRINKLER

WRENCH 80SS ~

(1) REFER TO rt & F2 ESCUTCHEON DATA TABLE FOR APPROVALS ANO DIM[NSIONS.

1..x I/r REDVCER

Model F1FR56/F1 or F2

CEILING

2 5/8" OIA. [66.7mm]HOLE IN CEILING

{1J REFER TO FP ESCUTCHEON DATA TABLE FOR APPROVALS AND DIMENSIONS.

Model F1 FR56/FP

2.

Model F1FR56 Quick Response Vertical Sidewall SprinklerInstallation Wrench: Model 0 Sprinkler WrenchInstallation Position: Upright or PendentApproval Type: Light Hazard OccupancyInstallation Data:

Nominal Nominal K Factor Sprinkler Approval SprinklerThread Size IdentificationOrifice US Metric Height Organizations Numbers (SIN)

Y2" (15mm) Y2" NPT (R1/2) 5.6 8.0 2.25" (57mm) 1.2.3,4RA 14892)

15mm W' NPT (R1/2) 5.6 8.0 2.25" (57mm) 4(1)

(1) LPC Approval is for pendent position only.(2) cULus Listed corrosion resistant (Polyester coated) sprinkler.

Sprinkler Type Deflector to Ceiling Distance(Min. - Max.)

Upright 4" (102mm) - 12" (305mm)

Pendent 4" (102mm) - 12" (305mm)

Model F1FR56 Quick Response Horizontal Sidewall SprinklerDeflector: HSWInstallation Wrench: Model 0 Sprinkler WrenchInstallation Data: Horizontal Sidewall

Nominal K Factor Sprinkler Approval OrganizationsSprinklerHeight and Type of Approval

Nominal Orifice Thread Size IdentificationUS Metric Light Hazard Ordinary Numbers (SIN)

Hazard

Y2" (15mm) W' NPT (R1/2) 5.6 80 2.63" (67mm) 1.2 1 RA 1435(1)

TURN COLLAR UNTILTIGHT AGAINST SPRINKLERWRENCH BOSS

I--------l 1 1/4"MIN

{JI.8mm] ( "4"-12" 2/

{IOI.6mm-J04.8mm}C£lLlNG TODEFLECTOR

(1) cULus Listed corrosion resistant (Polyester coated) sprinkler.~--------------~~~~~----------~~A

(I) ~T;~~/~:I~~frvG:----+--'-i

DIMENSION

2 1/4" HOLE DIA.{57.2mm}

I" X 1/2" REDUCER / il

=-/~---It

_oJ-'}---f,--:: :~I'I~i -,-,

1 15/16" DIA.II: II sm I

{49.2mm] . ::::: :

~

I 11111 :\._~I I .,.,.-4........J

L-.!----L __

2 27/32" DIA.(72.2mm]

~

Horizontal Sidewall

OIJFGOJB

~ ADJUSTMENT (7)

(I) REFER TO ESCUTCHEON DATA TABLE FOR APPROVALS AND DIMENSIONS.

(2) FM APPROVED FOR 4- - 6- {101.6MM - 152.4MM} C£lLlNG TO DEFLECTOR.

Note: For Recessed HSW Sprinklers use installation wrench GFR2.

I 3,

Model F1FR56==Co~led Pendent SprinklersInstallation Wrench: Model 1 sprinkyenchTechnical Data:

"K" Factor "~I

Temp. Rating Max. SprinklerNominal Th~;? BulbOrifice US Metric Siz Sprinkler

Ambient Color Approvals IdentificationCover Temp Number(SIN)

W' (15mm) 5.6 80 VNPT F1F~ ,,135°F/57°C 135°F/5JOC 100°F/38°C Orange 1 RA1414

%" (15mm) 5.6 80 if%" NPT F1FR ~/68°C 135°F/5JOC 100°F/38°C Red 1,4(1) RA1414

W' (15mm) 5.6 80 '12" NPT F1FR 175°F!?9°C 165°F/74°C 100°F/38°C Yellow 1 RA1414

W' (15mm) 5.6 80 '12" NPT F1FR 200°F/93°C 165°F/74°C 150°F/65°C Green 1 RA1414(1) ° ° "For VdS only - 155 F/68 C Norbulb and 1/2 [12,7mm] adjustment.

1/2" ADJUSTMENT

Figure 1

Installation AidA protective cap is included for use during installation.

Important: The F1FR56 Sprinkler with Model CCP coverplate is not an FM Approved combination.Installation

Quick response sprinklers are intended for installationas specified in NFPA 13. Quick response sprinklers andstandard response sprinklers should not be intermixe6.

The Model F1FR56 Recessed Quick Response Sprin-klers are to be installed as shown. The Model F1 or F2 Es-cutcheons illustrated are the only recessed escutcheonsto be used with the Model F1FR56 Sprinklers. The useof any other recessed escutcheon will void all approvalsand negate all warranties.

When installing Model F1FR56 Sprinklers, use the Mod-el D Sprinkler Wrench. Use the Model GFR2 Wrench forinstalling F1FR56 Recessed Pendent Sprinklers. Anyother type of wrench may damage these sprinklers.

NOTE: A leak tight Y2" NPT (R1/2) sprinkler joint canbe obtained with a torque of 8-18 ft-Ibs (10,8 - 24,4 N-m).Do not tighten sprinklers over maximum recommendedtorque. It may cause leakage or impairment of the sprin-klers.

The Model F1FR56/ CCP Concealed Sprinkler uses theW' orifice, Y2" NPT (R1/2), 135°F (5JOC), 155°F (68°C),175°F (79°C) or 200°F (93°C) Model F1FR56 Pendent

*DuPont Registered Trade Mark

,1 1/2" MAX.

FACE OF FITTINGT-"-"-'j TO FACE OF CEILING:~~;;;;; DIMENSION

~~~~~'~u.~.'.:./ t3/4"

5/16" ADJUSTMENT

Figure 2

Sprinkler with a threaded Model CCP cup which is fac-tory attached to the sprinkler. The assembly is complet-ed by the installation of the attractive, low profile, 135°F(57°C) or 165°F (74°C) rated Model CCP push on coverplate assembly. The cover plate and sprinkler cup as-semblies are joined using a cover plate skirt with flexibletabs for threaded engagement. A choice of two coverplate assemblies provide either Y2" (13mm) or 5/'6" (8mm)of cover adjustment.

Do not install these sprinklers in ceiling which havepositive pressure in the space above.

After a 25fs" (67mm) diameter hole is cut in the ceil-ing, the sprinkler is easily installed with the Model RC1Wrench. A Teflon* based thread sealant should beapplied to the sprinkler threads only. The Model RC1Wrench is then used to engage the sprinkler wrenchingsurfaces and to install the sprinkler in the fitting. Wheninserting or removing the wrench from the sprinkler/cupassembly, care should be taken to prevent damage tothe sprinkler. DO NOT WRENCH ON ANY OTHER PARTOF THE SPRINKLER. The cover plate is then pushedonto the cup. Final adjustment is made by hand turningthe cover plate until the skirt flange makes full contactwith the ceiling. Cover plate removal requires turning inthe counter clockwise direction.

4.

After installation, inspect all sprinklers to ensure thatthere is a gap between the cover plate and ceiling andthat the four cup slots are open and free from any air flowimpediment to the space above.

Concealed cover plate/cup assemblies are listed onlyfor use with specific sprinklers. The use of any other con-cealed cover plate/cup assembly with the Model F1FR56Pendent Sprinkler or the use of the Model CCP Concealedcover plate assembly on any sprinkler with which it is notspecifically listed my prevent good fire protection and willvoid all guarantees, warranties, listings and approvals.

Glass bulb sprinklers have orange bulb protectors tominimize bulb damage during shipping, handling andinstallation. REMOVE THIS PROTECTION AT THE TIMETHE SPRINKLER SYSTEM IS PLACED IN SERVICE FORFIRE PROTECTION. Removal of the protectors before thistime may leave the bulb vulnerable to damage. RASCOwrenches are designed to install sprinklers when c~are in place. REMOVE PROTECTORS BY UNDOING THECLASP BY HAND. DO NOT USE TOOLS TO REMOVETHE PROTECTORS.

Temperature RatingsSprinkler Max. AmbientClassification Temperature Bulb Color°c OF Temp.

0""""""'" "'2. 1"" 1nnoF (38°C) Orange- •~ ,....... Ordinary 68 155 100°F (38°C) Red

I . ,r, F (660C) YellowIntermediate 93 200 150°F (66°C) Green

Hiqh (1) 141 286 225°F I107°C) Blue(1) Not available for recessed sprinklers.

Escutcheon Data (1)

Escutcheon "A"Face of Fitting to

Model Approvals Adjustment Dimension Ceiling or WallDimension

~

,F1 1,3,4

Max Recess 1Y2"(38.1rrrn) 3/16"- 15/16"

MinRecess 3f."(19.1rrrnl (5mm-24mml

- " 11 ". "I _'6,L,u,

MinRecess 1"(25mrnl (5mm-17mmlFP Push-orv'

1,4Max Recessed 7/1e"(11mm) 1'/2" (38.1mm)

- 1 "125.4mml(1) SIN RA 1435 - cULus permits use with F1, F2 or FP escutcheons for "lighthazard" only, while FM limits use for same hazard with F2 escutcheon only.

MaintenanceThe Models F1FR56 and F1FR56 Recessed Sprinklers

should be inspected quarterly and the sprinkler systemmaintained in accordance with NFPA 25. Do not cleansprinklers with soap and water, ammonia or any othercleaning fluids. Remove dust by using a soft brush orgentle vacuuming. Remove any sprinkler which hasbeen painted (other than factory applied) or damagedin any way. A stock of spare sprinklers should be main-tained to allow quick replacement of damaged or oper-ated sprinklers. Prior to installation, sprinklers should bemaintained in the original cartons and packaging to mini-mize the potential for damage to sprinklers that wouldcause improper operation or non-operation.

Sprinkler TypesStandard UprightStandard PendentConventional A _Recessed Pendent ~Vertical SidewallHorizontal SidewallRecessed Horizontal sidewallConcealed pendent

Maximum Working Pressure175 psi (12 bar)100% Factory tested hydrostatically to 500 psi (34.5 bar)

Finishes (1)

Standard FinishesSprinkler Escutcheon Cover plate

~ """-0""Chrome Plated Chrome ~e~er ~ ~r~(4)(5) White DaiRted

Special Application FinishesSprinkler Escutcheon Cover plate

Bright Brass (3) Bright Brass Bright BrassBlack Plated Black Plated SatinBlack Paint (2) Black Paint Off WhiteOff White (2) Off White Black PaintSatin Chrome Satin Chrome Black Plated

(1) Other finishes and colors are available on special order .Consult the factory for details.

(2) cULus Listed only.(3) 200°F (93°C) maximum.(4) cULus listed "corrosion resistance" applies to SIN Numbers RA 1435

(HSW), RA 1485(VSW), RA 1425 (Upright) and RA 1414 (Pendent) instandard black or white.

(5) FM Approvals finish as "Polyester coated" applies to SIN NumberRA 1414 (Pendent) in standard black or white.

Ordering InformationSpecify:1. Sprinkler Model2. Sprinkler Type3. Orifice Size4. Deflector Type5. Temperature Rating6. Sprinkler Finish7. Escutcheon Type8. Escutcheon Finish (where applicable)9. Cover plate Model10. Cover plate Thread size11. Cover plate Temperature12. Cover plate Adjustment13. Cover plate Finish

Note: When Model F1 FR56 Recessed sprinklers are ordered, the sprin-klers and escutcheons are packaged separately.

5.

Reliable...For Complete ProtectionReliableoffersa wide selectionof sprinklercomponents. Followingare some of the manyprecision-madeReliableproductsthat guard lifeand propertyfromfirearoundthe clock.

• Automatic sprinklers• Flush automatic sprinklers• Recessed automatic sprinklers• Concealed automatic sprinklers• Adjustable automatic sprinklers• Dry automatic sprinklers• Intermediate level sprinklers• Open sprinklers• Spray nozzles• Alarm valves• Retarding chambers• Dry pipe valves• Accelerators for dry pipe valves• Mechanical sprinkler alarms• Electrical sprinkler alarm switches• Water flow detectors

• Deluge valves• Detector check valves• Check valves• Electrical system• Sprinkler emergency cabinets• Sprinkler wrenches• Sprinkler escutcheons and guards• Inspectors test connections• Sight drains• Ball drips and drum drips• Control valve seals• Air maintenance devices• Air compressors• Pressure gauges• Identification signs• Fire department connection

The equipment presented in this bulletin is to be installed in accordance with the latest published Standards of the National Fire Protection Association, FactoryMutual Research Corporation, or other similar organizations and also with the provisions of govemmental codes or ordinances whenever applicable.Products manufactured and distributed by Reliable have been protecting life and property for over 90 years, and are installed and serviced by the most highlyqualified and reputable sprinkler contractors located throughout the United States, Canada and foreign countries.

Manufactured by~ Recycled~ PaperReliable

The Reliable Automatic Sprinkler Co., Inc.(800) 431-1588 Sales Offices(800) 848-6051 Sales Fax(914) 829-2042 Corporate Officeswww.reliablesprinkler.comlnternet Address

Revision lines indicate updated or new data.

EG. Printed in U.S.A 08/11 PIN 9999970300