42
Obstacle Avoiding Robot PROJECT REPORT

Obstacle Avoiding Robot_report Robot23

Embed Size (px)

Citation preview

Page 1: Obstacle Avoiding Robot_report Robot23

PROJECT REPORT

Page 2: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

OBSTACLE AVOIDING ROBOT

SUBMITTED BY:

NAME ROLL NO.

SANDEEP BHOSALE 03

KALPESH CHHAJED 06

ABHIJEET KALBHOR 13

ABHIJEET KAPSE 15

GUIDED BY

Prof. Mr. Pravin MatteDepartment of Electronics and Telecommunication

G.H.R.C.E.M., Wagholi, Pune

University of PuneAcademic Year 2008-2009

Page 2

Page 3: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

G. H. RaisoniCollege of Engineering & Management

Certificate This is to certify that SANDEEP BHOSALE

KALPESH CHHAJED

ABHIJEET KALBHOR

ABHIJEET KAPSE

Studying in year T.E. branch E&TC have satisfactorily completed the project work of OBSTACLE AVOIDING ROBOT topic in fulfillment of mini project in Electronic System Design & Mini Project during the academic year 2008-09.

Project Guide H. O. D.Prof. Mr. Pravin Matte Prof. Mr. Vijay Joshi

Principal Dr. Mr. Dilip Shah

ACKNOWLEDGEMENTPage 3

Page 4: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

We feel profound pleasure in bringing out this projects report for which we have to go from pillar to post to make it a reality. This project work reflects contributions of many people with whom we had long discussions and without which it would not have been possible. We must first of all, express our heartiest gratitude to respected Prof. Pravin Matte (Dept. of E&TC) for providing us all guidance to complete project.

It would be unfair if we do not mention the invaluable contribution and timely co-operation extended to us by staff member of our department. And especially we can never forget the most worthy advices given by Col. Vijay Joshi (H.O.D., Dept of E&TC), that would help us the entire lifetime.

Last but not the least we express our sincere thanks to the institute G.H.R.C.E.M., Wagholi, Pune for providing such a platform for implementing the ideas in our mind.

Page 4

Page 5: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

INDEX Page No. 1. PREFACE

A) INTRODUCTION………………………………………………………..6

B) SCOPE OF PROJECT…………………………………………………..8

2. DESIGN OF THE PROJECT

A) PRELIMINARY DESIGN

i) BLOCK DIAGRAM………………………………………..10

ii) CIRCUIT DIAGRAM ……………………………………..12

iii) COMPONENT LIST………………………………………14

B) PROBLEMS ENCOUNTERED…………………………………………..15

C) FINAL DESIGN

i) PCB LAYOUT……………………………………………….17

ii) CIRCUIT DESCRIPTION………………………………….19

iii) ALGORITHM.………………………………………………20

iv) TESTING…………………………………………………….21

D) SOFTWARES USED……………………………………………………....23

i) DipTrace (ii) µVision Keil (iii) FlashMagic

3. SCOPE OF THE PROJECT

1.APPLICATIONS……………………………………………..27

2. FURTHER IMPROVEMENTS & FUTURE SCOPE……..29

4. BILL OF MATERIAL..................................................30

5. REFERENCES ..…………………………………….....32

Page 5

Page 6: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

INTRODUCTION

Page 6

Page 7: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

INTRODUCTION :

Robotics is part of Todays communication. In today’s world ROBOTICS is fast growing and interesting field. It is simplest way for latest technology modification. Now a days communication is part of advancement of technology, so we decided to work on ROBOTICS field, and design something which will make human life simpler in day today aspect. Thus we are supporting this cause.

This project is basic stage of any automatic robot. This ROBOT has sufficient intelligence to cover the maximum area of provided space. It has a infrared sensor which are used to sense the obstacles coming in between the path of ROBOT. It will move in a particular direction and avoid the obstacle which is coming in its path.

We have used two D.C motors to give motion to the ROBOT. The construction of the ROBOT circuit is easy and small .The electronics parts used in the ROBOT circuits are easily available and cheap too.

Page 7

Page 8: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

Scope of the project :

The project uses µc P89V51RD2 as the controlling element. It uses IR (Infra Red) sensors and two IR transmitting circuitry. When the obstacle comes in path of robot IR beam is reflected from the obstacle then sensor gives zero voltage to µc. This zero voltage is detected then µc decides to avoid the obstacle by taking left or right turn. If the sensor gives +5v to µc that means there is no obstacle present in it path so it goes straight until any obstacle is detected.

The two IR transmitter circuits are fitted on front and left side of robot. The two IR sensors are placed near to transmitters’ IR LEDs. The connections can be given from main circuit to sensors using simple twisted pair cables.

Two motors namely right motor and left motor are connected to driver IC (L293D). L293D is interface with µc. Micro-controller sends logic 0 & logic 1 as per the programming to driver IC which moves motors forward or reverse direction.

Page 8

Page 9: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

DESIGN

OF

pROJECT

BLOCK DIAGRAM :

MICRO-CONTROLL

ER

MOTOR DRIVER

RIGHT MOTOR

LEFT MOTOR

Page 9

Page 10: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

DESCRIPTION:

Basically circuit consist of following blocks:

1) Sensors2) Microcontroller 89V51RD23) Driver4) Motors

Let us take the overview of each block one by one.

1. IR Transmitter & Receiver The IR Transmitter block mainly used to

generate IR signal. It uses timer IC555 in astable multivibrator mode to generate square wave which have continuous pulses of 50% duty cycle of frequency 38 KHz. This transmitter is so arranged that the IR rays are focused on the sensor.

Page 10

Page 11: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

IR sensor (TSOP 1738) which gives normally 5v at output of it. After receiving infrared light at output of sensor we get 0v.

2. MicrocontrollerThis is the most important block of the

system. Microcontroller is the decision making logical device which has its own memory, I/O ports, CPU and Clock circuit embedded on a single chip.

3. DriverL293D is used as driver IC. Motors are connected to

this IC. According to program in µc it drives the left and right motor.

CIRCUIT DIAGRAM (Reference) :

Page 11

Page 12: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

Page 12

Page 13: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

TRANSMITTER :

2. COMPONENTS USED:

Page 13

Page 14: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

1) RESISTORS :

2)CAPACITOR:

3) OSCILLATORS:

4)ICs:

5) MISCELLANEOUS:

PROBLEMS FACED :

Page 14

VALUE QUANTITY

10K 21k,33E,330E,100E 28.2k,10K PULL UP 1

VALUE QUANTITY0.1,10,4.7 122 P 2

VALUE QUANTITY11.0592 MHz 1

VALUE QUANTITY89V51RD2 1L293D,7805 1

COMPONENT QUANTITY6V ,200 RPM DC MOTOR 2ZENER DIODE, 5.6V 3RESET SWITCH 16V DC BATTERY 2CONNECTING WIRES -

Page 15: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

Although the concept & design of the project seemed perfect, there were some problems faced while actual implementation:

1) Generation of exact 38Khz Frequency from IC 555 at

Transmitter circuit.

Solution : Use variable resistor pot in astable multivibrator. Connect IC 555’s output pin to C.R.O. & measure frequency pulses generated by IC 555.By varying the resistor pot we can adjust the frequency of output.

2) Availability of Burner:

Solution:as burner kit is not easily available, so we have design & implement hardware for burn the IC

Page 15

Page 16: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

FINAL DESIGN:

FINAL DESIGN

Page 16

Page 17: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

1. PCB LAYOUT:

TRANSMMITER :

Page 17

Page 18: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

2. CIRCUIT DESCRIPTION:

ELECTRICAL DESIGN:-

Page 18

Page 19: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

Components are properly mount on respective position. This include wiring and layout. The connection are given such that two IC’s i.e. 89V51RD2 & L293D are interface. To L293D we connect two motors namely left motor & right motor.

We implement transmitter circuit separately & gives power supply independentely. For power supply we use chargeable DC battery which having rating of 6V & 1.3A.Output pin of sensor(TSOP 1738) is connected to micro-controllers pin.

MECHANICAL DESIGN:-

It include front panel which is given with ball caster wheel which is fixed. Back panel is provided with circular wheel with DC motor of 12v and 100 rpm with suitable clip pin for fixing the tyre. All the assembly is fixed on base. All assembly mounted on single base.

ALGORITHM-:

1) Start

Page 19

Page 20: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

2) Initialize the input port & output port. Set the bit of port pin 1.0

3) Read data from port 1.

4) Check the bit on pin P1.0.

5) If bit is present move motors in forward direction. Else go to step 6.

6) If bit is not present on pin P1.0, then stop right motor & move left motor in forward direction until we get bit on pin p1.0.

7) Again go to step 3.

8) Stop.

TESTING:-

A) HARDWARE

B) SOFTWARE

Page 20

Page 21: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

A) Hardware:-

1. Continuity test:-

First of all we checked the PCB that all the tracks are as per the design of PCB and showing continuity with the help of multimeter and PCB layout.

2. Short circuit test :-

Then we checked the PCB for any unwanted short circuits with the help of multimeter and PCB layout.

3. Soldering:-

In the next step, we soldered the required components.and then checked that there are no any unwanted shorts occurred due to soldering without putting IC's and keeping power supply off.

4. Power supply test:-

In the next step, we put power supply on and checked whether required voltage is appearing at the required voltage is appearing at the required points i.e.+Vcc and GND at the respective points.we took care of not connecting IC's in the circuit while performing this test.

Page 21

Page 22: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

5. Microcontroller test:-

For testing the microcontroller, we wrote the square wave generation program for generating square wave on each port pin.Then we fed the program in microcontroller and checked the output with the help of CRO by connecting the microcontroller in the circuit. We took care of not connecting any other IC in the circuit.

Page 22

Page 23: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

SOFTWARES USED

Page 23

Page 24: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

SOFTWARES USED :

1. DipTrace

ROLE IN THE DESIGN:

DipTrace 1.50 proved to be a very handy & easy-to-use tool for the PCB layout process. Many of its features were utilized leading to an accurate & efficient design. It has Design Error Check & Electrical Rule Check tools which proved to be helpful in the design. It is loaded with a huge component list that is categorized in various libraries for giving simplicity. Placement of components is also very easy & they can be rotated in 360 to customize⁰ the design.

WORKING WITH DipTrace :

Page 24

Page 25: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

2. µVision Keil

ROLE IN THE DESIGN:

µVision Keil provides IDE for 8051 programming & is very easy to use. When starting a new project, simply select the microcontroller you use from the Device Database and the µVision IDE sets all Compiler, Assembler, Linker, and Memory options. It’s device database is large which supports many ICs of the 8051 family. A HEX file can be created with the help of Keil which is required for burning onto chip. It has a powerful debugging tool which detects most of the errors in the program.

WORKING WITH µVision Keil :

Page 25

Page 26: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

3. FlashMagic

ROLE IN THE DESIGN:

Flash Magic is a PC tool for programming flash based microcontrollers from NXP using a serial or Ethernet protocol while in the target hardware.  It has some excellent features like changeable baud rate, erase all flash before programming, setting security bits etc. The HEX file created with the help of keil was selected through it for programming the microcontroller.

WORKING WITH FlashMagic :

Page 26

Page 27: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

APPLICATIONS

Page 27

Page 28: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

APPLICATIONS :

1) This logic has been specially designed for vaccum cleaner. By using heavy rating motors ,strong mechanical structure and using highly sensitive obstacle sensors, it efficiently work as vaccum cleaner.

2)Just by making small changes in software this system can be used for avoiding concealed paths. This robot can effectively sense the obstacles and find out correct path.

3)With proper programming we can use it as a weight lifter.

4)In Mines.

Page 28

Page 29: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

FURTHER IMPROVEMENTS & FUTURE SCOPE :

1. Adding a Camera:

If the current project is interfaced with a camera (e.g. a Webcam) robot can be driven beyond line-of-sight & range becomes practically unlimited as networks have a very large range.

2. Use as a fire fighting robot :

By adding temperature sensor, water tank and making some changes in programming we can use this robot as fire fighting robot.

BILL OF MATERIAL:-

Page 29

Page 30: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

SR. NO. COMPONENTS QUANTITY AMOUNT

1. Microcontroller [89V51RD2]

1 85/-

2. L293D 1 70/-

3. 7805 2 12/-

4. TSOP1738 2 15

5. TIL38 2 10/-

6. Q804 1 55/-

7. Motor 2 300/-

8. PCB 3 200/-

9. Battery 1 250/-

10. Chassey 1 75/-

11. Crystal Oscillator (11.059MHz)

1 5/-

12. Capacitor (4.7/63) 2 4/-

13. Capacitor(0.01,0.1,10) 6 15/-

14. Connector 4 12/-

15. Resistor box 1 35/-

16 Transistor 5 5/-

17 Tyres 2 80/-

18 DMM 1 100/-

Page 30

Page 31: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

19 14 Pin Base 1 4/-

20 40 Pin Base 1 4/-

21 Screws 20 36/-

22 Ball caster 1 30/-

23 Reset switch 1 2/

24 Transformer(9V/1A) 1 40/-

Total 1444/-

Page 31

Page 32: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

REFERENCES

Page 32

Page 33: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

REFERENCES:

The 8051 Micro controller and Embedded systems.

(pearson Education)By-M.A.Mazidi

1. Wikipedia - The free encyclopedia

2. http://www.8051projects.info/

3. http://www.instructabal.com/

6.http://www.alldatasheet.com/

7. http://www.datasheet4u.com/

8.http://www.datasheetcatalog.com/

Page 33

Page 34: Obstacle Avoiding Robot_report Robot23

OBSTACLE AVOIDING ROBOTPROJECT REPORT

Conclusion:-

Thus, we believe that our project will be beneficial for various purposes & hence our efforts will be fruitful.

Page 34