-
1GOLDFIELD SCALEOPERATING MANUAL FOR ALL IN ONE PRINTER
Printer IndicatorAC POWER SUPPLY SPECIFICATION:-
Requires 10 to 15 Volt transformer with 4A Rating.
DC POWER SUPPLY SPECIFICATION:-Requires 6V battery with 1A to 5A
Rating.
TECHNICAL SPECIFICATION:-MCU:-Nuvoton based microcontroller with
internal EEPROM IC and crystal for lower
maintenance and higher life of the IC.ADC:- The mother card uses
latest AVIA technology based HX710, 24 bit delta sigma ADC
for higher resolution, for better accuracy and better linearity.
ADC is also has internal crystalso reduce the chance for crystal
failure errors with found in last decade.
1. Supply Voltage: 230V AC, 50Hz +/- 10%2. Operating
Temperature: 10 Degree C to 45 Degree c.3. Humidity: 10% to 95%
relative humanity (Non condensing).4. Power consumption: Max 10
watt.
-
25. Hysteresis:- 0.03% of Rated capacity.6. Linearity:- 99.9% of
the Rated capacity.
FEATURES:-1. Completely Customizable slip at customer side2. 16
alphanumeric character for Header13. 30 alphanumeric character for
header24. 30 alphanumeric character for footer5. Two customizable
line which can be edited6. Selection of no of copy of each print7.
Select among 5 different print slips8. 1000 memory9. 5 different
types of report10. Linear power supply and 8 hours of battery back
up11. Piece and liter modes of operation
KEYS:- There are 4 keys function in the mother board.KEY1 -
TARE/ENTERKEY2 - MODE/INCREMENTKEY3 - CAL PRESS/SHIFTKEY4 -
CAL_ENTER/PRINT/DECREMENT
NORMAL SCALE SETTING:-FIRM NAME SETTING:-
Indicator allows, entering 18 alphanumeric Character name i.e.
(A-Z, 0-9, BLANK)Steps:
1. 1st Switch OFF the scale, then Press & hold KEY2 (MODE /
INCREMENT) & switch ONthe scale.
2. Display shows UNLOCK, now release KEY 2.3. Now press KEY1
(TARE), Display will blank for password entry. Enter UNLOCK
PASS
2900 with the help of KEY2 (MODE / INCREMENT), KEY3 (CAL PRESS /
SHIFT) andKEY4 (DECREMENT) then press tare key.
4. Display -shows CHPASS then press tare key, then enter
PARAMETER LOCK PASSCUSTOME (IF NEEDED) with the help of KEY2 (MODE
/ INCREMENT) and KEY3(CAL PRESS / SHIFT) and then press tare
key.
5. Display shows NAME1, now press the tare key.6. Now display
shows old name, enter new names first 6 ALPHA NUMERIC
CHARACTERS
with the help of KEY2 (MODE / INCREMENT), KEY3 (CAL PRESS /
SHIFT) and KEY4(Decrement), then Press KEY1 (TARE) key to save the
name And for next 6 digitalphanumeric name.
7. Now Repeat the steps 5 and step 6 for NAME 2 & NAME 3
settings.8. Press KEY1 (TARE) key to save the name.9. Now NAME
setting is complete.10. The saved name will be shows as rolling
name when system starts.11. Now Printer name setting comes please
refer printer name setting for further
description.PRINTER NAME SETTING:-
1. After name setting done, press KEY1 (TARE), Display shows
-
32. PNAM1:- now press the KEY1 (TARE) key.3. Now display shows
old name, enter new names first 6 ALPHA NUMERIC CHARACTERS
with the help of KEY2 (MODE / INCREMENT), KEY3 (CAL PRESS /
SHIFT) and KEY4(Decrement), then Press KEY1 (TARE) key to save the
name.
4. PNAM2 to PNAM8 Repeat the steps 1 and step 2 for PNAM 2 to
PNAM8 settings.5. Press KEY1 (TARE) key to save the printer name
setting. Display shows
NOTE: PNAME 1 to 3 is used for 16 character header1 of slip
which is to be bold ornot boldPNAME4 to PNAME8 is 30 character
header2 of slip
6. PFEED:- Shows old value of paper feed at the end of slip,
Increment the value ofpaper feed by KEY2 (MODE / INCREMENT) and
KEY4 (DECREMENT) and Press KEY1(TARE) to store new setting.NOTE:
PFEED value can be 0 to 9, as per value it will blank space at
theend of each slip is printed
PARAMETER SETTINGS:-Steps:
1. 1st Switch OFF the Scale, then Press & hold KEY3 (CAL
PRESS / SHIFT) & switch onthe scale.
2. Display shows PASS. Now release KEY 3 & press KEY1
(TARE), then enterPARAMETER LOCK PASS CUSTOM (Set in Name setting)
with the help of KEY2(MODE / INCREMENT), KEY3 (CAL PRESS / SHIFT)
and KEY4 (Decrement) then presstare key. If password is wrong
display shows pass then Re-enter correct password.NOTE: Default
Password is 0000 if custom pass is not set.
3. Display shows PARMTR. Now press the KEY1 (TARE). Display
shows CS i.e. capacityselection.
4. Now select capacity as per requirement using KEY2 (MODE /
INCREMENT) (CS=1 forcapacity 1, CS=2 for capacity 2 & CS=3 for
capacity 3) then Press KEY1 (TARE).
5. Display shows CAP1, then press KEY1 (TARE).6. Display shows
last stored capacity 1, enter new capacity with the help of KEY2
(MODE
/ INCREMENT), KEY3 (CAL PRESS / SHIFT) and KEY4 (DECREMENT) then
press KEY1(TARE) to store new capacity.
7. Display shows ACC1 it shows old, for entering new value,
increment the accuracy byKEY2 (MODE / INCREMENT) and Press KEY1
(TARE),
8. Display shows DP1 it shows old, for entering new value,
increment the dp segment byKEY2 (MODE / INCREMENT) and Press KEY1
(TARE).
9. Then repeat the steps 5, 6, 7 and step 8 for CAP2 & CAP3
settings with its Accuracyand dp settings. Press KEY1 (TARE).
Display shows,
10. AUTO ZERO (A 0) SETTING:- Increment the value of auto off /
zero tracking valueby KEY2 (MODE / INCREMENT) and Press KEY1
(TARE). Display shows,
11. DUMMY ZERO (D 2):- Increment the DMY value by KEY2 (MODE /
INCREMENT) toactivate dummy zero and press KEY1 (TARE). Display
shows,
12.MODE SETTINGS:- This mode is used for different mode of the
weighing, whichincludes following different types of the
weighing,To select different mode select as per given below,Select
0 = To weighing/work in normal i.e. in grams or in kgs.Select 1 =
To weighing/work in Piece countingSelect 2 = To weighing/work in
liter
-
4Press KEY1 (TARE). Display shows,
13. DSP SETTING:-This mode is for saving electricity or power.
If the all six digit will glow in standby modethe electricity
consumption is more. To save the electricity only single digit will
glow instandby mode by selecting the,Select 0 = Shows all zero. For
DP3 it shows 0.000Select 1 = For single digit glow (To save
electricity). Single zero on screenSelect 2 = For only running dp
(Decimal Point) glow (To save more electricity)Press KEY1 (TARE),
Display shows,
14. LITER:- Press KEY1 (TARE). Now display shows old liter value
enter new litervalue by KEY2 (MODE / INCREMENT), KEY3 (CAL PRESS /
SHIFT) and KEY4(DECREMENT) then press KEY1 (TARE) to store new
liter value, Display shows,NOTE: Enter liter value as how much
liter for 1kg, For eg. If 940ml liter =1kg then enter 940 here.
15. LACC:- Press KEY1 (TARE). Now display shows old liter
accuracy value enternew liter value by KEY2 (MODE / INCREMENT),
KEY3 (CAL PRESS / SHIFT) andKEY4 (DECREMENT) then press KEY1 (TARE)
to store new liter accuracy value, Displayshows,
16. STCT:- Now display shows old stability count value, enter
new stability countvalue by KEY2 (MODE / INCREMENT) and KEY4
(DECREMENT) then press KEY1(TARE) to store new value, Display
shows,Note: Better result and stability keep it 3
17. STTM:- Now display shows old stability time value, enter new
stable time valueby KEY2 (MODE / INCREMENT) and KEY4 (DECREMENT)
then press KEY1 (TARE) tostore new value, Display shows,Note:
Better result and stability keep it 5
18. SER NO:- Press KEY1 (TARE). Now display shows current serial
number, toenter new serial number value by KEY2 (MODE / INCREMENT),
KEY3(SHIFT ) andKEY4 (DECREMENT) then press KEY1 (TARE) to store
new current serial value, Displayshows,Note: SERIAL NUMBER 0 reset
all data.
19. PRNT:- Now display shows print setting, enter new print
setting by KEY2(MODE/ INCREMENT) and KEY4 (DECREMENT) then press
KEY1 (TARE) to store new printsetting, Display shows,0- Manual
Print1- Automatic print after stability.
NOTE:- stability time and count can be set by STCT and STTM.20.
Your parameter setting complete.
CALIBRATION:-Calibration can be done in weighing mode,
-
5Steps:1. First On/Start the weighing scale. Press KEY1 (TARE)
for TARING the weight.2. Put the standard weight on the scale,
weight should be 1/3rd of the Full capacity.3. Then press &
hold KEY3 (CAL PRESS / SHIFT) & press KEY4 (CAL ENTER /
COUNT).4. Display shows PASS. Now release KEY 3 and KEY4. now press
KEY1 (TARE), then
enter PARAMETER LOCK PASS CUSTOM (Set in Name setting) with the
help of KEY2(MODE / INCREMENT) and KEY3 (CAL PRESS / SHIFT) then
press tare key. Ifpassword is wrong display shows pass then
Re-enter correct password & Press Key (T).
5. Display shows CAL Press KEY1 (TARE). Then display show the
count changed. Thendisplay shows 000000.
6. Now enter the weight by incrementing KEY2 (MODE / INCREMENT)
and KEY3 (CALPRESS / SHIFT) for Shifting.(E.g. If putted standard
weight is 2Kg, to enter 2000. when display shows 000000Then press
KEY2 (MODE / INCREMENT) key two times so that display shows
000002now press KEY3 (CAL PRESS / SHIFT), 3 times so the display
shows 002000).
7. Now Press KEY1 (TARE) key. Calibration is successfully
done.
CHANGE IN WEIGHING MODE-If weighing mode is different than
normal gram mode 0 in parameter setting,
then to change between selected mode and weighing mode press
KEY2 (MODE /INCREMENT).ENTER LITER VALUE:-
Liter value is entered in parameter setting point 14 and its
accuracy point 15.ENTER COUNT VALUE:-
To enter the piece value first set the piece counting mode by
changing weighingmode into piece counting by KEY2 (MODE). In piece
counting display shows P. Nowpress KEY1 for TARE.
Now Put counted Pieces on scale pan then PRESS KEY3 (CAL
PRESS/SHIFT)key And hold for 10 seconds displays shows SETPCS and
then 000000.
Now enter number of pieces putted on scale with the help of KEY2
(MODE /INCREMENT), KEY3 (CAL PRESS / SHIFT) and KEY4 (DECREMENT).
And pressKEY1 (TARE), to store piece counting value now display
shows no of pieces youentered.(NOTE:- For better Result Put minimum
100 pieces on pan).DISPLAY INTERNAL COUNT:-
For displaying internal ADC count. Switch ON SCALE by pressing
KEY4 (CAL ENTER/COUNT). Release the KEY display show internal ADC
COUNTS.
To exits from counts press KEY2 (MODE /INCREMENT).
-
6PRINTER SLIP SETTING:-
Print Slip with field nameSwitch off scale and now press
KEY1(TARE) and KEY2(MODE) both together andswitch on the scale.
1. Display Shows STPRT, Press KEY1 (TARE), display shows,2.
SFMT:- Now display shows old slip format selected, enter new slip
format as
you want from below list using KEY2 (MODE / INCREMENT) and
KEY4(DECREMENT) then press KEY1 (TARE) to store new value, Display
shows,0- Party name two header, date time, weight, footer
SFMT = 01- Party name two header, serial no, date time, weight,
footer
-
7SFMT=12- Party name two header, serial number, date time, gross
weight, tare
weight, net weight, footer
SFMT=23- Party name two header, serial number, date time,
weight, quantity or
liter (as per mode selected) , footer
SFMT=2 MODE=1 SFMT=2 MODE=24- Party name two header, serial
number, date time, list of partial weight
that needs to be added, gross weight, footer
-
8SFMT=4
3. H1:- Now display shows old header setting, enter new setting
by using KEY2(MODE / INCREMENT) and KEY4 (DECREMENT) then press
KEY1 (TARE) to store newvalue, Display shows,0- Header 1 is not
print on slip1- Header 1 is print on slip
4. H2:- Now display shows old header setting, enter new setting
by using KEY2(MODE / INCREMENT) and KEY4 (DECREMENT) then press
KEY1 (TARE) to store newvalue, Display shows,0- Header 2 is not
print on slip1- Header 2 is print on slip
5. STR1:- Now display shows old star/dash line 1 setting, enter
new setting byusing KEY2 (MODE / INCREMENT) and KEY4 (DECREMENT)
then press KEY1 (TARE)to store new value, Display shows,0- First
star/dash line is not print on slip1- First star/dash line is
printed on slip
6. STR2:- Now display shows old star/dash line 2 setting, enter
new setting byusing KEY2 (MODE / INCREMENT) and KEY4 (DECREMENT)
then press KEY1 (TARE)to store new value, Display shows,0- Second
start/dash line is not print on slip1- second star/dash line is
printed on slip
-
97. DTSH:- Now display shows old date show setting, enter new
setting by usingKEY2 (MODE / INCREMENT) and KEY4 (DECREMENT) then
press KEY1 (TARE) tostore new value, Display shows,
0- DATE is not print on slip1- DATE is printed on slip
8. TMSH:- Now display shows old time show setting, enter new
setting by usingKEY2 (MODE / INCREMENT) and KEY4 (DECREMENT) then
press KEY1 (TARE) tostore new value, Display shows,
0- Time is not print on slip1- Time is printed on slip
9. H1BLD:- Now display shows old header 1 bold setting, enter
new setting byusing KEY2 (MODE / INCREMENT) and KEY4 (DECREMENT)
then press KEY1 (TARE)to store new value, Display shows,
0- Header1 is printed normal if header1 is selected for print in
H1setting
1- Header1 is printed bold if header1 is selected for print in
H1 setting10. SERPN:- Now display shows old serial number print
setting, enter new setting
by using KEY2 (MODE / INCREMENT) and KEY4 (DECREMENT) then press
KEY1(TARE) to store new value, Display shows,0- Serial number is
not print on slip1- Serial number is printed on slip
11. STDS:- Now display shows old dash/star/minus setting, enter
new setting byusing KEY2 (MODE / INCREMENT) and KEY4 (DECREMENT)
then press KEY1 (TARE)to store new value, Display shows,0- Print
------------------------------ line in line1 And line21- Print
********************* line in line1 And line22- Print
================== line in line1 And line2
12. COPY:- Now display shows old no of copy setting, enter new
setting by usingKEY2 (MODE / INCREMENT) and KEY4 (DECREMENT) then
press KEY1 (TARE) tostore new value, Display shows,
Enter 1 to 9 for that no of same print copy when given print
command.Eg. Copy = 3 then it prints 3 copy of same print.NOTE: COPY
Is not work in STFM = 4 i.e. for partial weighment.
13.FOOT:- Now display shows old footer setting, enter new
setting by using KEY2(MODE / INCREMENT) and KEY4 (DECREMENT) then
press KEY1 (TARE) to store newvalue, Display shows,0- Footer is not
printed on slip1- Footer is printed on slip
If footer is selected 1 it will ask for footer characters.If
footer selected as 0 it will go to step14.Display shows FOOT1 press
KEY1 (TARE), display shows old first 6 charactersof footer now
enter new characters by using KEY2 (ICREMENT), KEY3 (SHIFT),KEY4
(DECRMENT) and once done press KEY1 (TARE) for storing.
-
10
Now asked for FOOT2, FOOT3, FOOT4 , FOOT5 enter similarly total
30alphanumeric character can be printed for footer.
14.L1N1:- Now display shows old customize line setting, enter
new setting by usingKEY2 (MODE / INCREMENT) and KEY4 (DECREMENT)
then press KEY1 (TARE) tostore new value, Display shows,0-
Customize line 1 is not printed on slip1- Customize line 1 is
printed on slip
If L1N1 is selected 1 it will ask for line1 characters.If L1N1
selected as 0 it will go to step15.Display shows L1 1 press KEY1
(TARE), display shows old first 6 characters ofline 1 now enter new
characters by using KEY2 (ICREMENT), KEY3 (SHIFT),KEY4 (DECRMENT)
and once done press KEY1 (TARE) for storing.Now asked for L1 2, L1
3, L1 4, L1 5 enter similarly total 30 alphanumericcharacter can be
printed for customize line1.NOTE: L1 1 and L1 2 total 11 character
placed at left side of : and L1 3 to 5 isprinted right side of : in
slip.EG: PROD NAME : WEIGHT SCALE can be entered asL1 1: PROD NL1
2: AMEL1 3: WEIGHTL1 4: SCALEL1 5:
So it will print line PROD NAME : WEIGHT SCALE IN slip15.L1N2:-
Now display shows old customize line 2 setting, enter new setting
by
using KEY2 (MODE / INCREMENT) and KEY4 (DECREMENT) then press
KEY1 (TARE)to store new value, Display shows,0- Customize line 2 is
not printed on slip1- Customize line 2 is printed on slip
If L1N2 is selected 1 it will ask for line2 characters.If L1N2
selected as 0 it will go to step15.Display shows L2 1 press KEY1
(TARE), display shows old first 6 characters ofline 1 now enter new
characters by using KEY2 (ICREMENT), KEY3 (SHIFT),KEY4 (DECRMENT)
and once done press KEY1 (TARE) for storing.Now asked for L2 2, L2
3, L2 4, L2 5 enter similarly total 30 alphanumericcharacter can be
printed for customize line1.NOTE: L2 1 and L2 2 total 11 character
placed at left side of : and L2 3 to 5 isprinted right side of : in
slip.EG: MAKE : GOLDFIELD can be entered asL1 1: MAKEL1 2:L1 3:
GOLDFL1 4: IELDL1 5:
So it will print line MAKE : GOLDFIELD in slip16. Your printer
setting is done
-
11
DATE AND TIME SETTING:-Switch off scale and now press KEY3(CAL
PRESS/SHIFT) and KEY4(CAL_ENT /DEC )both together and switch on the
scale.
1. Display Shows DATSET, Press KEY1 (TARE), display shows,2.
HOUR:- Press KEY1 (TARE). Display shows 00, Now enter current hour
value
using KEY2 (MODE / INCREMENT), KEY3 (SHIFT) and KEY4 (DECREMENT)
thenpress KEY1 (TARE) to store new HOUR setting and display
shows,
3. MIN:- Press KEY1 (TARE). Display shows 00, Now enter current
minute valueusing KEY2 (MODE / INCREMENT), KEY3 (SHIFT) and KEY4
(DECREMENT) thenpress KEY1 (TARE) to store new minute setting and
display shows,
4. DATE:- Press KEY1 (TARE). Display shows 00, Now enter current
date valueusing KEY2 (MODE / INCREMENT), KEY3 (SHIFT) and KEY4
(DECREMENT) thenpress KEY1 (TARE) to store new date setting and
display shows,
5. MON:- Press KEY1 (TARE). Display shows 00, Now enter current
month valueusing KEY2 (MODE / INCREMENT), KEY3 (SHIFT) and KEY4
(DECREMENT) thenpress KEY1 (TARE) to store new month setting and
display shows,
6. YEAR:- Press KEY1 (TARE). Display shows 00, Now enter current
year valueusing KEY2 (MODE / INCREMENT), KEY3 (SHIFT) and KEY4
(DECREMENT) thenpress KEY1 (TARE) to store new year setting and
display shows,
NOTE: Please enter current date time in 24 hours format
strictly.
REPORT PRINTING:-Switch off scale and Press KEY1 (TARE) and
switch on Scale, display shows
1. Display Shows RTYPE2. RTYPE:- Display shows old set value,
Now enter current report setting value
using KEY2 (MODE / INCREMENT) and KEY4 (DECREMENT) then press
KEY1 (TARE)to store new report format value and display shows,
3. RPT: Press KEY1(TARE), Display shows old set value, Now enter
currentreport setting value using KEY2 (MODE / INCREMENT) and KEY4
(DECREMENT)then press KEY1 (TARE) to store new rpt format value and
display shows,
-
12
RTYPE0 SERIAL NO and WEIGHT Printed in reportRPT-0 all serial no
wise report
RTYPE = 0 RPT = 0RPT-1 DATE wise report
RTYPE = 0 RPT = 1
-
13
RPT-2 SINGLE SERIAL no wise report
RTYPE = 0 RPT = 2RPT-3 SERIAL NO RANGE wise report,
RPT-4 PRODUCT wise report if customer added customize
line1RTYPE1 SERIAL No GROSS TARE NET printer in report
RTYPE=1 RPT=0
-
14
RPT-0 all serial no wise reportRPT-1 DATE wise reportRPT-2
SINGLE SERIAL no wise reportRPT-3 SERIAL NO RANGE wise report,RPT-4
PRODUCT wise report if customer added customize line1
RTYPE2 SERIAL NO, WEIGHT QUANTITY OR LITER (As per MODE
value)printed in report
RTYPE=2 RPT=0RPT-0 all serial no wise reportRPT-1 DATE wise
reportRPT-2 SINGLE SERIAL no wise reportRPT-3 SERIAL NO RANGE wise
report,RPT-4 PRODUCT wise report if customer added customize
line1
RTYPE3 SERIAL NO DATE TIME WEIGHT printed in report
RTYPE=3 RPT=0
-
15
RPT-0 all serial no wise reportRPT-1 DATE wise reportRPT-2
SINGLE SERIAL no wise reportRPT-3 SERIAL NO RANGE wise report,RPT-4
PRODUCT wise report if customer added customize line1
RTYPE4 SERIAL NO, NO OF ITEMS WEIGHT printed in report
RTYPE=4 RPT=0RPT-0 all serial no wise reportRPT-1 DATE wise
reportRPT-2 SINGLE SERIAL no wise reportRPT-3 SERIAL NO RANGE wise
report,RPT-4 PRODUCT wise report if customer added customize
line1
