NVR Series User Manual-201405.14 (1).doc

8/20/2019 NVR Series User Manual-201405.14 (1).doc

1/64

Preface

Attentions:

Welcome to use our network video recorder. For your secure using, please read

this user manual carefully. The following contents are about the proper use of theproduct, the prevention of danger and loss of property etc. Please be sure toabide.1. Installation Environment:

Please place and use this product in the environment with temperature 0℃-0℃!

The device should be placed hori"ontally when it is being installed andused, avoid lean or inversion!#o not place or install it in the high temperature, wet, dusty and sootyplaces.$eep the device away from water drop or plash. #on%t put any ob&ect withli'uid inside like flower vase or any other ob&ect on the device.To ensure the normal heat dissipation of the device, there is a fan installedinside the device. The device should be installed in well-ventilatedenvironment!The back of the #() should be away from other devices or the wall above*cm in order to release heat!+f the device is used in the regions with much thunder, please installlightning protection device to avoid host or hardware breakdown by

lightning stroke.2. Attentions:

#o not touch the power switch and the () by wet hands or wet ob&ects, inorder to avoid electric shock! fter installing the host, please make sure that the host and the chassis areconnected to the ground in order to avoid video and audio signalinterference and damaged by static electricity!

nsure the voltage stability of the power supply of the (). /se the power input with stable voltage value and little wave interference rather thanshutdown the () by disconnecting the main switch directly!


2/64

etwork (ideo )ecorder /ser anual

#o not drop any li'uid or metal on the () in case short circuit inside or fire!The device does not include any hard disk, and you need to properly installthe hard disk before using it, otherwise, you cannot record and playback thevideo!The dust on the mainboard will cause short circuit when it is damp. +n order to ensure the long-term normal working, you should regularly dedust themainboard, connectors, chassis, fan and so on by a brush!#o not disconnect the power switch directly when you want to shutdown the

(). 1ou should use the shutdown button on the panel in order to avoid

damage to the hard disk!The device system supports 2## format function. +f the 2## has beenused, please take note that if it is with F T 34 format. This () onlysupports 2## with F T 34 format! #o not open the device when it is connected with electricity! To ensure the integrity of the recording data, please replace the hard disk

when it is damaged 5there is disk error record in the log information6.3. Note:

The user manual is for reference only. The real ob&ect is the standard!The products will be updated at any time. +t is sub&ect to update withoutnotice.Please contact our technical department for the latest programs andadditional documentation.+f there is any doubt or dispute, our company reserves the right of finale7planation.

This user manual offer references to multi-series products. The specific operationof each product will not be listed one by one. Please contact our technicaldepartment when you have any 'uestion.

- 4 -


3/64

Contents82 PT ) 9: P);#/8T +


4/64


3.3.? )ecord Eackup........................................................................43.3.A / = ) 8;)# ..........................................................................4*3.3. = ) +F;) T+; ......................................................................4*

3.3.90 8apture................................................................................4?3.3.99 File anager..........................................................................4?

82 PT ) B: TW;)$ ;P ) T+ > + + ;P ) T+ > + < ;F T2 () W2+82


5/64


Chapter 1: Product Instruction

1.1 Product Summary

This device is a video coding and recording product specially designed for thevideo monitoring field, combining with 2.4*B video compression, large capacity2## storage, T8P@+P network, embedded =inu7 operating system and other various advanced electronic information technologies, reali"ing high-'ualityimage and low bit rate recording features andfavourable system stability.

The device meets the standard of >E 40A9 -400* H(ideo


6/64


Chapter 2: Installation Instruction

2.1 "pen#case Inspection

When you receive the product, please check all the things according to the ()packing list in the bo7.

2.2 $%% Installation

+nstallation Preparation:

eed one cross screwdriver. This series of 2## () can install 4 to A pieces of 2## inside, and the capacity of each 2## can be up to 4TE.2## +nstallation


7/64


Chapter 3: &ocal "peration 'uide

3.1 Start(Shutdo)n System

3.1.1 Start System

Plug power cable, press power switch, the power led will be on and the () willstart. fter booting, the video output default to multi-window output mode. +f thebooting time is within the record setting time period, the system will auto enablethe record function.Notice: Please use the () matching power supply instead of any other power supply of any other type or brand.3.1.2 Shutdo)n System

8lick J click


8/64


3.3 enu "peration

3.3.1 Start Setup

8lick , and the interface will display:

96


9/64


Notice: +P address might conflict with each other, please set the gatewaycorrectly, or () might fail to work. Please ensure all the +P addresses in =are uni'ue.

Then click the right mouse button and appear the below menu:

%evice port settin+: the default is 0 0, if there are several ()s in the = ,need to change this port is for login () by + , 8


10/64


8lick H+P 8hannel


11/64


)ight click to select +P channel


12/64


3# positioning and alarm status will appear in the right upper corner.

3.3.3 Previe)

3.3.3.1 %ra+ and %rop the Ima+e

The preview image location can be drag and drop to different place asnecessary, but the channel physical address will keep the same5 TT : channelnumber in red circle as below6

Preview image can randomly drag to ad&ust according to actual managementre'uirement, which makes surveillance management more systematic andfriendly.

3.3.3.2 %ra+ to Chan+e Channel

Se uence

#uring real video surveillance, it%s

- 94 -


13/64


very important to havepreview channel position of +P8 image.


14/64


3.3.4 %isplay Settin+

8lick , the interface on the right will show:

96 )esolution: select the most appropriate resolution as needed!46 =anguage: #ifferent languages for selection 5For e7ample:


15/64


3.3.4.2 P5 Settin+

96 Preset setting: first turn the camera to the needed position through thedirection buttons of the PTC control, then select a preset number, and clickH


16/64


3.3.6.1 %evice Parameters

7%evice Info8 8heck and modify the basic information of the device.8lick


17/64


18/64


Su Stream @9*@4 @3* screens display are using sub stream, + or mobilereviewing are sub stream also.

ain Stream ;Event< motion detection and alarm trigger recording are using

this

46


19/64


20/64


B #o the setting according your necessary in the pop out screen, like larm on

onitor,


21/64


7,ideo &ost8 8an modify the parameters of each channel.96 H larm


22/64


23/64


8lick H)efreshI, and find the WiFi router and double click. Then input the ipaddress, subnet mask, default gateway, # < server address9 and # <server address 4.

46 nable 3>: Tick the bo7 before H nable 3>I, click H3>I to enter the followinginterface:

a. The access number of the 8hina /nicom is Q P address is:3> T.

b. The access number of the 8hina Telecom is Q??? P address isblank.

c. The access number of the 8hina obile is 9Q P address is

blank.36 dvance:

a6 # <


24/64


46 TP Port: This < TP only supports T8P transmission. +t is default to 943.36 T: 1ou can do fine ad&ustment of time.

7Email Settin+s8


25/64


26/64


3.3.6. $%% Settin+s

1ou can format the 2## and view the 2## capacity, the free space and statusetc.

3.3. .? System @p+rade

)ight click mouse, click


27/64


and save it in the assigned place of / disc!+mport configuration : ;pen the menu in the ()s

that need the same configuration,import data of / discto copy the () conf iguration.

3.3.6.B %evice &o+

1ou can search the logs according to different types and different date and time,as shown in the above picture.

9. ain Type of =og: There are ll Type, larm, 7ception and ;peration for selection.

4.


28/64


Channel Select: select the channels that need do playback, system will find there'uired recording file. The date that has recording is highlighted by red color incalendar %ate Select: select the playback date

Search: it will auto search the recording which meet the search condition asshown in the below picture.

Play ac=: after choosing the date, 4B hours color bar will show. #ifferentrecording way will show in different color. d&ust the time line by mouse rollerbetween 4 hours, 9 hours, 30 minutes, minutes and 9 minute. The playbacktime can be specified to second

96 Pause: pause the current playback image.46


29/64


device, click )efresh to detect the /


30/64


3.3.B Alarm Information

8lick , and the interface on the right will show:

ll the alarm information of the device is recorded in the H larmI list. 3.3.1D Capture


31/64


32/64


Chapter 4: Net)or= "peratin+ Instruction

4.1 >E0 0ro)ser "peratin+ Instruction

4.1.1 Net)or= Connection

8onfirm the () correct access to the network.


33/64


The operation of + is same as inthe local ().

)emark: open the preview, click the right bottom to let it change to or right click toOpen All , the red point represent recording , and click to setthe stream and switch of main stream and sub stream.This doesn t re'uire for router setting, e7cluding of registering domain name.

4.2 N,* IE ,ie)in+ "peration Instruction for A%S& ode

+f customer connects with #


34/64


8lick ## < for setting.

96 The physical address can keep the same!46 +P address: the +P must be the uni'ue and cannot conflict with other host or

workstationg 9 4.9*A.9.909

36 #efault >ateway: be same with the = gateway, eg: 9 4.9*A.9.9a6


35/64


4.2.2 *outer Settin+

s the so many different router brands, take the TP-=+ $ router as thee7ample, please do the operation as the following:

9. ;pen + browser and input the gateway, like:http:@@9 4.9*A.9.94. +nput theUser Name and Password to login the router management

TP-=+ $ default user name: admin, password: admin,3. 8lick the HForwarding )ulesI of tool bar at the left side, some router named it

by Port apping, click Virtual Server click Adding New Items dd the following () +P address to there and save it.

2TTP Port: default number A0#evice Port: default number 0 0#efault Port: default number 0 9#efault Port: default number 0 48ell Phone Port: default number 0 3 fter finish it and click the item“ All entries effect”

ow take 3344 as the e7ample, bound the dynamic +P addresswww.3344.org tofi7ed domain name. nter 3344 website and input the application information.Take note the domain name after applying successfully.

Note: domain name, user name and password need to add on the ## < settingof #() network setting.

ow input the applied domain in the + browser, you can login the ().Note: I f you fail to login in, please try again by adding colon M http port number.

4.2.3 IE &o+in "perations

;pen + browser and input the domain name, then it pop out the followinginformation: #ownloading activ7, please wait or click here.

;nce the download has completed, please close + browser first beforeun"ipping the installation package. fter installation finished, then open the +browser and input the domain name, login with port number, user name andpassword. The default user name is admin and no password. Then you will see

- 3 -

http://192.168.1.1/http://www.3322.org/http://192.168.1.1/http://www.3322.org/


36/64


37/64


B 8lick H8ustom =evelIN #isable HEinary and


38/64


* 8lick HToolsI ---H8ompatibility (iew


39/64


;r also you can tick the compatibility button if you can see H I

A For the + 99,if you can%t find option H#isplay all websites in 8ompatibility (iewI,then please tick Hdisplay intranet sites in 8ompatibility (iewI and add the site oneby one.

- 3 -


40/64


8lickI )unI when prompt turns out like below:

90 8lick H #ownload unsafe file I

99 +f you still can%t see the video on the + (iew, then please carry out belowsetting on the P896 >o to menu of H8ontrol PanelI, and then click H ccounts and Family


41/64


46 nter the H/ser ccountsI, and then click H8hange /ser ccount 8ontrol


42/64


ow setting up is done. +f you still can%t login () through + , please turn off your firewall:

+f you still can%t see the video on the + (iew, then please ensure you have madeport forwarding with following ports: 0 0, 0 9, 0 4, 0 3, A0 on your router if () remote port is default 0 0. 52ere Phone view port is 0 36

P.


43/64


Chapter 6: P2P Cloud !unction

P4P 8loud, simple and stable, doesn t re'uire for router setting, e7cluding of registering domain name. 8aution:9: etwork rchitecture could not have second level router.4: ake sure () has P4P functions and check if it has +cloud protocol 5


44/64


=ike right interface,8lick H/+#I)ecord ame: ust be filled but randomly./+#: fill with ()


45/64


#evice +# is ()


46/64


6.2 5he Parameter Settin+s of the N,* )hich Supports o ile

Surveillance

)esolution: 8+F or O8+F!Frame )ate: -90fps! and so on.Installation and "peration Instruction

9. 8opy the 1 U ndroid.apk to the mobile or download it from >oogledirectly.

4. 8lick the program to install.3. 8lick to run the program as shown in the picture on the right:

5he functions of the uttons are as elo):FunctionEutton

ame Function #escription

Play Program connects the device and start to play thevideo


47/64


bout bout the information.


48/64


49/64



50/64



51/64


9. 8opy the 1 UW .cab to the mobile and install it.8lick the corresponding program icon to open as shown in the picture on theright.

Function Eutton ame Function #escription

8onnect andPlay

Program connects the device andstart to play the video


52/64


devices!3. fter successful setting, press K;$L button to enter the connection interface.The image will appear if connected successfully.

6. iPhone o ile System

obile client supports iphone system version i;< 3.0 or higher version, includingiPhone,iPod touch and so on.Installation and "peration Instruction

9. )un the pp


53/64



54/64


Chapter : Appendi

.1 $%% Capacity Calculation ethod for *eference

+nstall the network video recorder for the first time, please make sure whether the2## is installed inside the host.

.1.1 5he Capacity of the $%%

The digital video recorder re'uires a single 2## with above 00>E capacity. +norder to obtain better stability, we recommend the 2## with 00> V 4TEcapacity.

.1.2 5he Selection of the 5otal Capacity

8alculate the total capacity of a () re'uires according to the recordingre'uirement recording type, recording file storage time . 8alculation method


55/64


id bit rate /nit $bit@s

The following table shows the recording file si"e of the common bit rate under constant bit rate within one hour and one day for one channel.The second step: after confirming the time re'uirement of recording, calculate the storage capacity i m one channel re'uires according toformula546, unit: Eyte.

im iq Y ih Y i D 4

ih recording time of each day 2our

i D number of days of recording storage

For e7ample: the 2## capacity for recording one month for 9 channel 9. 0 bitstream. /nit >E.

im * Y4BY39 B 04 * E B?A>E

The third step: the total capacity 5accumulating6 'T for 9* channels timingrecording for a whole day. /nit: >E

t q 16q im Y9* ?*BA>E

+f select 00> 2##, 9* pieces of 2## will be re'uired to full record. /ser selectsappropriate 2## according to the capacity.The fourth step: calculate the total capacity5accumulating6 needed for allchannels alarm recording5including motion detection6. /nit: >E

t q Ya%

a% alarm occurring rate.

larm occurring rate: 1T

M 2T M 3T

MZZ nT 6@n 24T 5n 9 4 3Z6

nT The alarm time of the th day5the time difference of larm end and alarm

- -


56/64


start6 /nit: h 24T 4Bh

t q the needed 2## capacity of T channels timing

For e7ample: if the alarm occurring ratea% for a month is 0[, then the alarmrecording capacity of 9* channels in one month is: /nit:>E

t q Ya% 16q Y 0% ?*BAY 0% 3.?>E

.2 *emote Control "peration

umb +con #escription umber +con #escriptio

9 ) 8 )ecord $ey 93 +\\ =ast


57/64


58/64


4. Program error! please try to reboot the ().3. 2## data error caused by bad track and bad clusters, please detect the

2##. +f the 2## is defective, please replace the 2##.B. 2ardware error of (), please contact the supplier.

N,* cannot connect net)or=.

Possible causes:9. Please check if the network physical connection is correct.4. Please check the () network parameter configuration.3. Please check if +P conflict e7ists in the network.

5he do)nload or ac=up recordin+ video fail to play

Possible causes:9. Player is not installed correctly.4. The file system error of the backup / disk or removable hard disk.3. >raphics speed up software whose version is above #GA.9 is not installed.

$o) to do N,* firm)are @pdate

For access to some functions and re'uirements, () needs to updatefirmware.Eefore update, users need to prepare as below:9 To check


59/64


B kinds of ordinary situations as below,96 +P 8amera +P address can be searched, multi-images sub stream and

single image main stream all cannot have image!46


60/64


?40Y ?*, please be aware if main stream resolution ratio and +P8%s arematched!

4 Ey +P8%s + 5+P8 +P address access6 or P8 8lient, users need to ad&ust+P8%s sub stream for resolution ratio of (> or 8+F!

3 To update () firmware.


61/64


Audio fails to monitor

96 +P camera audio enable or not: check out and open up audio to seewhether +P camera has E1; pick-up via + or +P camera E1; client appon P8!

46 udio format: ad&ust audio format to >.?99 via + or +P camera E1; clientapp on P8!

36 ():


62/64


HdvrUactive7I whole folder, while deleting HdvrUactive7I folder inHProgram Files57A*6KWin?DALI, then install new active7.

B6 fter successfully installing active7, input () +P address on +browser address bar and login interface appeared. Port for ())emote Port as default is 0 0 in port, admin in user name and nopassword. Tick HloginI and click right mouse to see H;pen llI or tickthe Y to in every screen right corner.

>AN Access:

)ecommend to shut down () and close router%s /P P, then do the portmapping. +f open /P P without () shut down, it may have mapping

conflict and () /P P is default to be closed.+f users have static +P, it needs to map two rules in router, first is 0 0- 0 3,related to () +P address! second is A05


63/64


which can be found on ndroid market and pp store. For + end P4P,open + browser and inputhttp:@@www.goolink.org on address bar andthen register an account. fter successful registeration, refreshhttp:@@www.goolink.org and after active7 is successfully loaded, it willhave a black screen in the middle of the page. ow users turn to adddevice in device management and device +# is from users% ()


64/64


can decode () or ; (+F protocol%s +P cameras. For detail, please carefullyview it on #ecode 8# disk.

Documents

NVR Series User Manual-201405.14 (1).doc