NuMicro Family Nu-Link-Gang User Manual · 2019-12-23 · Power1 Power2 Power3 Power4 Adapter Board Connector Slot1 Slot2 Slot3 Slot4 Single-start Button Start1 Start2 Start3 Start4

Nu-Link-Gang

Dec. 23, 2019 Page 1 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

ARM® Cortex

®-M0

32-bit Microcontroller

NuMicro® Family

Nu-Link-Gang

User Manual

The information described in this document is the exclusive intellectual property of Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton.

Nuvoton is providing this document only for reference purposes of NuMicro microcontroller based system design. Nuvoton assumes no responsibility for errors or omissions.

All data and specifications are subject to change without notice.

For additional information or questions, please contact: Nuvoton Technology Corporation.

www.nuvoton.com

http://www.nuvoton.com/

Nu-Link-Gang

Dec. 23, 2019 Page 2 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

Supported devices of Nu-Link-Gang

Cortex-M0 series

M031 M051 M0518 M0519 M0564

M058S Mini51 Mini51X Mini57 Mini58

NM1120 NM1200 NM1230 NM1320 NM1330

NM1500 NM1810 NM1820 TF5100 Nano100

Nano103 NDA102 NUC029 NUC100 NUC121

NUC126 NUC131 NUC200 AU9110 I91000

N569 N570 N572 N575 N576

Cortex-M4 series

M451 NUC400 NUC505 M480 I94000

Cortex-M23 series

M251 M2351 M261

8051 series

N76E003 N76E616 N76E885 ML51 MS51

Nu-Link-Gang

Dec. 23, 2019 Page 3 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

Table of Contents

1 GENERAL DESCRIPTION ..................................................................................................... 5 2 HARDWARE INTRODUCTION............................................................................................... 6

2.1 Nu-Link-Gang ............................................................................................................... 6

2.1.1 Programming Unit............................................................................................................. 7 2.1.2 Power Supply ................................................................................................................... 7 2.1.3 Programming Mode Switch .............................................................................................. 8 2.1.4 LCD Display and LCD Control Button............................................................................... 8 2.1.5 Programming Voltage Switch ........................................................................................... 8 2.1.6 Status LED ....................................................................................................................... 8 2.1.7 Control Bus ....................................................................................................................... 9 2.1.8 Upgrade Interface ............................................................................................................. 9

2.2 Nuvoton ICP Gang Adapter ....................................................................................... 10

2.2.1 Status LED ..................................................................................................................... 10 2.3 Nuvoton NUC505 ICP Gang Adapter ......................................................................... 11

2.3.1 IC Mode Switch .............................................................................................................. 11 2.3.2 Status LED ..................................................................................................................... 12

3 NU-LINK-GANG PROGRAMMER SETUP ........................................................................... 13 3.1 Choose the Programming Voltage ............................................................................. 13

3.2 Set the Programming Mode ....................................................................................... 13

3.3 Load Firmware Image Files through NuMicro® ICP Programming Tool .................... 13

3.3.1 Connect to ICP Programming Tool ................................................................................. 13 3.3.2 ICP Programming Tool Setting ....................................................................................... 13 3.3.3 Import/Export Project ...................................................................................................... 14

3.4 Connect to the Target Chip ........................................................................................ 15

3.4.1 Nuvoton ICP Gang Adapter ............................................................................................ 15 3.4.2 Customized Adapter Board ............................................................................................ 15

3.5 Start Programming ..................................................................................................... 16

3.5.1 Programming .................................................................................................................. 16 3.5.2 LCD Display ................................................................................................................... 16

4 NU-LINK-GANG PROGRAMMER SETUP FOR NUC505 SERIES ..................................... 19 4.1 Choose the Programming Voltage ............................................................................. 19

4.2 Set the Programming Mode ....................................................................................... 19

4.3 Connect to the Target Chip ........................................................................................ 19

4.3.1 Nuvoton NUC505 ICP Gang Adapter ............................................................................. 19 4.3.2 Customized Adapter Board ............................................................................................ 20

4.4 IC Mode Switch .......................................................................................................... 20

4.5 Load Firmware Image Files through NuMicro® ICP Programming Tool .................... 20

4.5.1 Connect to ICP Programming Tool ................................................................................. 20 4.5.2 ICP Programming Tool Setting ....................................................................................... 21 4.5.3 Import/Export Project ...................................................................................................... 22

4.6 IC Mode Switch .......................................................................................................... 22

4.7 Start Programming ..................................................................................................... 23

Nu-Link-Gang

Dec. 23, 2019 Page 4 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

4.7.1 Programming .................................................................................................................. 23 4.7.2 LCD Display ................................................................................................................... 23

5 NU-LINK-GANG PROGRAMMER SETUP FOR AUTOMATIC IC PROGRAMMING SYSTEM ......................................................................................................................................... 25

5.1 Software and Hardware Setup ................................................................................... 25

5.1.1 Connection ..................................................................................................................... 25 5.1.2 Waveform ....................................................................................................................... 26

6 NU-LINK-GANG PCB SCHEMATIC ..................................................................................... 27 6.1 Control Unit Schematic............................................................................................... 27

6.2 Power and Connection Schematic ............................................................................. 28

6.3 #1 NuLink Schematic ................................................................................................. 29




6.7 LCD Display Schematic.............................................................................................. 33

7 TROUBLESHOOTING .......................................................................................................... 34 7.1 Pop-up Warning Message When Programming NUC505 Series .............................. 34

7.2 Nu-Link-Gang Firmware Update ................................................................................ 34

7.3 Programming Unit Firmware Update .......................................................................... 34

8 REVISION HISTORY ............................................................................................................ 36

Nu-Link-Gang

Dec. 23, 2019 Page 5 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

1 GENERAL DESCRIPTION

The Nu-Link-Gang programmer is the new generation four-chip gang programmer, supports all Nuvoton NuMicro

® Family and 8051 1T series and packages. The Nu-Link-Gang provides flexible

programming setting, which is designed especially for mass-production. It supports four different chips with individual firmware image file programming functionality, 3 options of programming voltage, and off-line programming four chips simultaneously or individually. The Nu-Link-Gang can also be connected to a automatic IC programming system. Overall, the Nu-Link-Gang offers more flexibility and high efficiency than what usual programmers offer for mass-production.

The Nu-Link-Gang programmer is easy to use. User first loads the programming firmware image file through ICP programming tool on PC into the programmer, then use only one botton to start the off-line programming process. The LCD display on the Nu-Link-Gang shows the detail of IC’s part number, programming times, programming voltage, error message, and etc. User can connect the Nu-Link-Gang programmer and target chips by using a automatic IC programming system, Nuvoton ICP Gang Adapters or customize adapter boards. Different ICs or different packages use different Nuvoton ICP Gang Adapters.

Figure 1-1 Nu-Link-Gang Programmer

Nu-Link-Gang

Dec. 23, 2019 Page 6 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

2 HARDWARE INTRODUCTION

2.1 Nu-Link-Gang

#1 #2 #3 #4

LCD Display

LCD Control Button

(Bottom) Upgrade interface

All-start Button Power LED

A

Adaptor Board Connector

Single-start Button

Programming Voltage Switch

Status LED

Adaptor Board Aid Connector

(Top) USB Connector

A

Programming Mode

Switch

Power Button

DC9V Power Input

B

B

Control Bus

(Right side)

Control Bus Pin

Assignment

Programming Unit #1 ~ #4

Figure 2-1 Nu-Link-Gang

Nu-Link-Gang

Dec. 23, 2019 Page 7 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

2.1.1 Programming Unit

Programming unit #1, #2, #3, and #4, four independent units with identical functions.

Programming unit #1 #2 #3 #4

USB Connector USB1 USB2 USB3 USB4

Status LED FAIL1

PASS1 FAIL2

PASS2 FAIL3

PASS3 FAIL4

PASS4

Programming Voltage Switch

Power1 Power2 Power3 Power4

Adapter Board Connector

Slot1 Slot2 Slot3 Slot4

Single-start Button Start1 Start2 Start3 Start4

Control Bus

PASS1 FAIL1

BUSY1 START1

PASS2 FAIL2

BUSY2 START2

PASS3 FAIL3

BUSY3 START3

PASS4 FAIL4

BUSY4 START4

Table 2-1 Programming Unit’s Component List

2.1.2 Power Supply

Use DC 9V/1A power adapter with DC tip polarity: internal positive (+), external negative (-).

Power ON: Connects the Nu-Link-Gang and the power adapter, and press the Power Button once. The LCD display and the Power LED illuminates.

Power OFF: Press the Power Button once to release it. The Power LED does not illuminate, and the Nu-Link-Gang truns off. Remove the power adapter from the Nu-Link-Gang.

Programming Mode Switch

Power Button

DC9V Power Input

Figure 2-2 Power Supply and Programming Mode Switch

Nu-Link-Gang

Dec. 23, 2019 Page 8 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

2.1.3 Programming Mode Switch

Switches the programming mode as shown as Figure 2-2 to control Single-start button or All-start button.

All-start button controls all four programming units. Each Single-start button controls corresponding unit.

Programming Mode Switch

StartALL Start1 Start2 Start3 Start4

Single Start X V V V V

All Start V X X X X

X:Unused Table 2-2 Programming Mode Switch

2.1.4 LCD Display and LCD Control Button

The LCD display shows each unit’s detail such as IC’s part number, programming times, programming voltage, error message, and etc. Uses LCD control buttons to switch pages.

Enter Button

Select Button

LCD Display

Figure 2‑3 LCD Display and Control Buttons

2.1.5 Programming Voltage Switch

Turns off the Nu-Link-Gang, and switches the programming voltage to 1.8 V, 3.3 V, or 5.0 V.

Programming Voltage 1 2 3

Figure 2-4 Programming Voltage Switch

5.0 V ON OFF OFF

3.3 V OFF ON OFF

1.8 V OFF OFF ON

Table 2-3 Programming Voltage Switch

2.1.6 Status LED

The status LEDs on the Nu-Link-Gang and the Nuvoton ICP Gang Adapter show the programming results of every unit.

Nu-Link-Gang

Dec. 23, 2019 Page 9 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

Light Status

Figure 2‑5 Status LED

Green PASS

Red FAIL

Table 2-4 Status LED on Nu-Link-Gang

2.1.7 Control Bus

The Nu-Link-Gang can be connected to a automatic IC programming system through the control bus.

Figure 2‑6 Control Bus

2.1.8 Upgrade Interface

JP15 is the SWD interface only for the Nu-Link-Gang firmware upgrade.

Figure 2-7 JP15

Nu-Link-Gang

Dec. 23, 2019 Page 10 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

2.2 Nuvoton ICP Gang Adapter

The pin 1 of the socket is at the bottom left corner. Different chips or different packages use different Nuvoton ICP Gang Adapters. Please refer to section 3.4.1 for the usage.

Supported IC

Status LED

#1 #2 #3 #4

Figure 2-8 Nuvoton ICP Gang Adapter

Programming Unit #1 #2 #3 #4

Nuvoton ICP Gang Adapter #1 #2 #3 #4

Status LED on Nuvoton ICP Gang Adapter

LED1 LED2

LED3 LED4

LED5 LED6

LED7 LED8

Table 2-5 Nuvoton ICP Gang Adapter Component List

2.2.1 Status LED


Light Status


Green PASS

Red FAIL

Table 2-6 Status LED on Nuvoton ICP Gang Adapter

Nu-Link-Gang

Dec. 23, 2019 Page 11 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

2.3 Nuvoton NUC505 ICP Gang Adapter

The pin 1 of the socket is at the bottom right corner, marked in white arrow. Different packages use different Nuvoton NUC505 ICP Gang Adapters.

Supported IC

Status LED

#1 #2 #3 #4

Reset Button

IC Mode List

IC Mode Switch

Figure 2-10 Nuvoton NUC505 ICP Gang Adapter

Programming Unit #1 #2 #3 #4

Nuvoton ICP Gang Adapter #1 #2 #3 #4

Status LED on Nuvoton ICP Gang Adapter

LED1 LED2

LED3 LED4

LED5 LED6

LED7 LED8

IC Mode Switch on Nuvoton NUC505 ICP Gang Adapter

SW1 SW2 SW3 SW4

Table 2-7 Nuvoton NUC505 ICP Gang Adapter Component List

2.3.1 IC Mode Switch

The IC mode switch on the NUC505 Nuvoton ICP Gang Adapter must be set before programming process. Please refer to chapter 4.

Mode 1 2 3 4

Figure 2-11 IC Mode Switch

Mode 1 OFF OFF ON OFF

Mode 2 OFF OFF OFF ON

Table 2-8 IC Mode Switch

Nu-Link-Gang

Dec. 23, 2019 Page 12 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

2.3.2 Status LED


Light Status


Green PASS

Red FAIL

Table 2-9 Status LED on Nuvoton NUC505 ICP Gang Adapter

Nu-Link-Gang

Dec. 23, 2019 Page 13 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

3 NU-LINK-GANG PROGRAMMER SETUP

3.1 Choose the Programming Voltage

The Nu-Link-Gang supports three kinds of programming voltage, 1.8 V, 3.3 V, or 5.0 V. Users can choose different programming voltage for each programming unit by setting corresponding programming voltage switch. Please sets the programming voltage before the Nu-Link-Gang power on.

3.2 Set the Programming Mode

Switch the programming mode to single-start or all-start.

3.3 Load Firmware Image Files through NuMicro® ICP Programming Tool

Please access Nuvoton NuMicro® website (http://www.nuvoton.com/NuMicro) to download the

NuMicro ICP tool - ICP Programming Tool. Unzip the file and execute “NuMicro ICP Programming Tool.exe”. Please refer to section 3.3.1 and 3.3.2 for the detailed flow. For more information, please refer to the “Nuvoton NuMicro ICP Programmer User Guide”.

3.3.1 Connect to ICP Programming Tool

Connects one programming unit’s to PC through USB connector as Figure 3-1, then open the ICP Programing Tool on the PC.

Figure 3-1 Nu-Link-Gang Connects to PC

3.3.2 ICP Programming Tool Setting

1. Choose “Connect”. The window will shows “NuLink connected” when the connection between programming unit and ICP Programming Tool is built.

http://www.nuvoton.com/NuMicro

Nu-Link-Gang

Dec. 23, 2019 Page 14 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

2. Load the firmware image files to the corresponding flash region.

3. Set the Config Bits by the using IC series.

4. Select the programming area.

5. Set the program option. It is necessary to select the “Offline Programming Mode” option.

6. Click “Start”. The ICP Programming Tool will start loading the firmware image files to the Nu-Link-Gang.

User needs to repeat section 3.3.1 and 3.3.2 to load firmware image file to every programming unit.

1.Connect

2.Load File

3.Config Bits

4.Programming 5.Option 6.Start

5.Option

Figure 3-2 ICP Programming Tool Setting

3.3.3 Import/Export Project

The user settings of the ICP Programming Tool can be save and load by import or export the .icp project file. It can also do the binary code protection through exporting with a ceritificate.

Figure 3-3 ICP Programming Tool Import/Export Project

Nu-Link-Gang

Dec. 23, 2019 Page 15 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

3.4 Connect to the Target Chip

3.4.1 Nuvoton ICP Gang Adapter

Connect the Nuvoton ICP Gang Adapter to Nu-Link-Gang as Figure 3-4. Put the target chip into the socket. Pin 1 is on the bottom-left hand side.

Figure 3-4 Nuvoton ICP Gang Adapter with Nu-Link-Gang

3.4.2 Customized Adapter Board

Follow Figure 3-5 to connect the adapter board and the Nu-Link-Gang slot. The slot VCC pin voltage is set by the programming voltage switch.

The recommended wiring between adapter board and the Nu-Link-Gang is using stranded conductors with AWG size 24 and length 50 cm.

Figure 3-5 Slot Pin Description

Nu-Link-Gang

Dec. 23, 2019 Page 16 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

3.5 Start Programming

3.5.1 Programming

Plug-in a 9V/1A power adapter to the Nu-Link-Gang and press the Power button once as Figure 3-6.

Figure 3-6 Nu-Link-Gang Power On

1. To start the programming process, press the Start ALL button or the individual Start button depends on the programming mode switch setting.

2. The status LEDs on the Nu-Link-Gang and the Nuvoton ICP Gang Adapter will show the programming results of every unit.

Green light: PASS.

Red light: FAIL.

3. Change the target chip in the adapter, and repeat section 3.5 process.

3.5.2 LCD Display

Users can switch pages by pressing buttons to show the individual programming unit’s status and information. There are four pages:

Page 1: Shows all four units programming status includes programming times and programming voltage as Figure 3-7. Press Enter button to go to the next page.

Page 2: Programming unit selection page as Figure 3-8. Press Select button to choose the unit. The choosen unit is high-lighted in yellow. Press Enter button to go to the next page.

Nu-Link-Gang

Dec. 23, 2019 Page 17 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

Page 3: Shows programming unit Information as Figure 3-9. List the programming chip’s part number, programming unit’s version number, maximum programmable times, PASS/FAIL status records, and error code. Press Enter button to go to the next page.

Page 4: Shows programming unit Information as Figure 3-10. List the checksum data of every programming area, and config bits. The checksum data and config bits are the same as the data in ICP Programming Tool. Press Enter button to go to page 1.

Programming Unit Enter Button

Select ButtonPage

PASS Status FAIL Status Programming Voltage

Target Chips Part Number

Figure 3-7 Page 1 – Programming Status


Select ButtonPage

Figure 3-8 Page 2 - Programming Unit Selection Page

Programming Unit

Enter Button

Select ButtonPage

Target Chip Part NumberUnit Version Number

Maximum Programmable TimesPASS Status

FAIL StatusError Code

Figure 3-9 Page 3 - Programming Unit Information

Nu-Link-Gang

Dec. 23, 2019 Page 18 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

Checksum Value

Enter Button

Select ButtonPage

Config Bit

Figure 3-10 Page 4 - Programming Unit Information

Connects the Nu-Link-Gang to the target chip before to the computer, and then config the ICP Programming Tool as 3.3, the part number of the target chips will shows on the LCD display as Figure 3-11 and Figure 3-12.


Select ButtonPage


Figure 3-11 All Four Target Chips are the Same Part Number


Select ButtonPage


Figure 3-12 At Least One Different Part Number Target Chip

Nu-Link-Gang

Dec. 23, 2019 Page 19 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

4 NU-LINK-GANG PROGRAMMER SETUP FOR NUC505 SERIES

4.1 Choose the Programming Voltage

The Nu-Link-Gang supports three kinds of programming voltage, 1.8 V, 3.3 V, or 5.0 V. Users can choose different programming voltage for each programming unit by setting corresponding programming voltage switch. Please sets the programming voltage before the Nu-Link-Gang power on.

4.2 Set the Programming Mode

Switch the programming mode to single-start or all-start.

4.3 Connect to the Target Chip

4.3.1 Nuvoton NUC505 ICP Gang Adapter

Connect the Nuvoton NUC505 ICP Gang Adapter to Nu-Link-Gang as Figure 4-1. Put the target chip into the socket. Pin 1 is on the bottom-right hand side, marked in white arrow.

Figure 4-1 Nuvoton NUC505 ICP Gang Adapter with Nu-Link-Gang

Nu-Link-Gang

Dec. 23, 2019 Page 20 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

4.3.2 Customized Adapter Board

Follow Figure 4-2 to connect the adapter board and the Nu-Link-Gang slot. The slot VCC pin voltage is set by the programming voltage switch.

The recommended wiring between adapter board and the Nu-Link-Gang is using stranded conductors with AWG size 24 and length 50 cm.

Customized adapter board for NUC505 must have IC mode switch and Reset button function. If users have customized adapter board demand, please contact Nuvoton Technology Corporation for adapter board specifications.

Figure 4-2 Slot Pin Description

4.4 IC Mode Switch

Switch four programming units’ IC mode to Mode 1 on the Nuvoton NUC505 ICP Gang Adapter as Figure 4-3.

Figure 4-3 IC Mode in Mode 1

4.5 Load Firmware Image Files through NuMicro® ICP Programming Tool

Please access Nuvoton NuMicro® website (http://www.nuvoton.com/NuMicro) to download the

NuMicro ICP tool - ICP Programming Tool. Unzip the file and execute “NuMicro ICP Programming Tool.exe”. Please refer to section 4.5.1 and 4.5.2 for the detailed flow. For more information, please refer to the “Nuvoton NuMicro ICP Programmer User Guide”.

4.5.1 Connect to ICP Programming Tool

Connects one programming unit’s to PC through USB connector as Figure 4-4. Press the Reset button on the Nuvoton NUC505 ICP Gang Adapter, and then open the ICP Programing Tool on the PC.

http://www.nuvoton.com/NuMicro

Nu-Link-Gang

Dec. 23, 2019 Page 21 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

Figure 4-4 Nu-Link-Gang Connects to PC

4.5.2 ICP Programming Tool Setting

1. Choose “Connect”. The window will shows “NuLink connected” when the connection between programming unit and ICP Programming Tool is built.

2. Load the firmware image files to the corresponding flash region.

3. Set the program option. It is necessary to select the “Offline Programming Mode” option.

4. Click “Start”. The ICP Programming Tool will start loading the firmware image files to the Nu-Link-Gang.

User needs to repeat section 4.5.1 and 4.5.2 to load firmware image file to every programming unit.

Nu-Link-Gang

Dec. 23, 2019 Page 22 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

1.Connect

2.Load File

3.Programming Area 5.Start

4.Program Options

4.Program Options

Figure 4-5 ICP Programming Tool Setting

4.5.3 Import/Export Project

The user settings of the ICP Programming Tool can be save and load by import or export the .icp project file. It can also do the binary code protection through exporting with a ceritificate.

Figure 4-6 ICP Programming Tool Import/Export Project

4.6 IC Mode Switch

Switch four programming units’ IC mode to Mode 2 on the Nuvoton NUC505 ICP Gang Adapter as Figure 4-7.

Nu-Link-Gang

Dec. 23, 2019 Page 23 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

Figure 4-7 IC Mode in Mode 2

4.7 Start Programming

4.7.1 Programming

Plug-in a 9V/1A power adapter to the Nu-Link-Gang and press the Power button once as Figure 4-8, and press the Reset button on the Nuvoton NUC505 ICP Gang Adapter.

Press the Start ALL button or the individual Start button depends on the programming mode switch setting to start the programming process. The status LEDs on the Nu-Link-Gang and the Nuvoton NUC505 ICP Gang Adapter will show the programming results of every unit. Change the target chip in the adapter, and repeat section 4.6 process.

Figure 4-8 Nu-Link-Gang Power On

4.7.2 LCD Display

LCD display shows four units programming status includes programming times and programming voltage as Figure 4-9. The LCD control buttons function please refer to section 3.5.2.

Nu-Link-Gang

Dec. 23, 2019 Page 24 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

Figure 4-9 LCD Display

Nu-Link-Gang

Dec. 23, 2019 Page 25 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

5 NU-LINK-GANG PROGRAMMER SETUP FOR AUTOMATIC IC PROGRAMMING SYSTEM

5.1 Software and Hardware Setup

Follow section 3.1 and 3.3 to setup the programming voltage and firmware image file for four programming units individually. Switch the programming mode to single-start.

5.1.1 Connection

Each programming units connects to the automatic IC programming system through individual slot and the control bus as Figure 5-1.

(Left side)Slot Pin Description

(Right side)Control Bus Pin Description

A

A

B

B

Figure 5-1 Automatic IC Programming System Connection

Nu-Link-Gang

Dec. 23, 2019 Page 26 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

5.1.2 Waveform

1. The Nu-Link-Gang power on. STARTx, BUSYx, PASSx, and FAILx are set to logic 1.

2. To start programming, STARTx needs to be set to logic 0 for TSTART, .

3. Programming start-up. BUSYx is set to logic 0 , and might toggle during programming.

4. When finish programming, BUSYx is set to logic 1, and PASSx or FAILx is set to logic 0.

When BUSYx is set to logic 1, and PASSx is set to logic 0, means “PASS”.

When BUSYx is set to logic 1, and FAILx is set to logic 0, means “FAIL”.

STARTx

BUSYx

PASSx

FAILx

TSTART

Figure 5-2 PASS Waveform

STARTx

BUSYx

PASSx

FAILx

TSTART

Figure 5-3 FAIL Waveform

Nu-Link-Gang

Dec. 23, 2019 Page 27 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

6 NU-LINK-GANG PCB SCHEMATIC

6.1 Control Unit Schematic

UART_TXD_DUART_RXD_D

UART_RXD_DUART_TXD_D

All_KEYAll_KEY

ICE

CL

KIC

ED

AT

LCM_VCC_CtrlLCM_VCC_Ctrl

ADAVSS

JP15

ICE_HEADER 5X2 (簡易牛角90度)

1 23 45 67 89 10NUC_RST#

ICECLKICEDAT

VCC33

UA

RT

_R

XD

_A

UA

RT

_T

XD

_A

Buzzer

VCC33

BUZZER

R733

R0603 BZ1

2400Hz

12

L2 FERRITE BEAD

VCC33AVDD

L1 FERRITE BEAD

ADAVSS

Link2_VCCLink1_VCC

Link3_VCCLink2_VCCLink1_VCC

Link4_VCCLink3_VCC Link4_VCC

C3

0.1u

M0_RXDM0_TXD

AVDD

U16<M0518SD2AE>

PB

.14

/IN

T0

1

PB

.13

2

PB

.12

/CL

KO

/BP

WM

1_

CH

33

PF

.5/I

2C

0_

SC

L/P

WM

1_

CH

54

PF

.4/I

2C

0_

SD

A/P

WM

1_

CH

45

PA

.11

/I2

C1

_S

CL

/PW

M1

_C

H3

6

PA

.10

/I2

C1

_S

DA

/PW

M1

_C

H2

7

PA

.9/I

2C

0_

SC

L/U

AR

T1

_n

CT

S8

PA

.8/I

2C

0_

SD

A/U

AR

T1

_n

RT

S9

PB

.4/U

AR

T1

_R

XD

10

PB

.5/U

AR

T1

_T

XD

11

PB

.6/U

AR

T1

_n

RT

S12

PB

.7/U

AR

T1

_n

CT

S13

LD

O_

CA

P14

VD

D15

VS

S16

PB.0/UART0_RXD17PB.1/UART0_TXD18PB.2/UART0_nRTS/TM2_EXT/PWM1_BRAKE1/TM219PB.3/UART0_nCTS/TM3_EXT/PWM1_BRAKE0/TM320PD.6/BPWM1_CH121PD.7/BPWM1_CH022PD.14/UART2_RXD/BPWM0_CH523PD.15/UART2_TXD/BPWM0_CH424PC.3/SPI0_MOSI0/BPWM0_CH325PC.2/SPI0_MISO0/BPWM0_CH226PC.1/SPI0_CLK/BPWM0_CH127PC.0/SPI0_SS0/BPWM0_CH028PE.5/PWM0_CH5/TM1/TM1_EXT29PB.11/TM3/PWM0_CH430PB.10/TM231PB.9/TM132

PC

.11

/PW

M1

_B

RA

KE

133

PC

.10

/PW

M1

_B

RA

KE

034

PC

.9/P

WM

0_

BR

AK

E1

35

PC

.8/P

WM

0_

BR

AK

E0

36

PA

.15

/PW

M0

_C

H3

37

PA

.14

/PW

M0

_C

H2

38

PA

.13

/PW

M0

_C

H1

/UA

RT

5_

TX

D39

PA

.12

/PW

M0

_C

H0

/UA

RT

5_

RX

D40

PF

.7/I

CE

_D

AT

41

PF

.6/I

CE

_C

LK

42

AV

SS

43

PA

.0/A

DC

0/I

2C

1_

SC

L/U

AR

T5

_T

XD

/PW

M0

_C

H4

44

PA

.1/A

DC

1/I

2C

1_

SD

A/U

AR

T5

_R

XD

/PW

M0

_C

H5

45

PA

.2/A

DC

2/U

AR

T3

_T

XD

/PW

M1

_C

H0

46

PA

.3/A

DC

3/U

AR

T3

_R

XD

/PW

M1

_C

H1

47

PA

.4/A

DC

448

PA.5/ADC5/UART3_RXD49

PA.6/ADC6/UART3_TXD50

PA.7/ADC7/Vref51

AVDD52

PC.7/UART4_RXD/I2C0_SCL/PWM0_BRAKE153

PC.6/UART4_TXD/I2C0_SDA/PWM0_BRAKE054

PC.1555

PC.1456

PB.15/INT1/TM0/TM0_EXT/BPWM1_CH557

XT1_OUT/PF.058

XT1_IN/PF.159

nRESET60

VSS61

VDD62

PF.8/CLKO/BPWM1_CH463

PB.8/TM0/STADC/CLKO/BPWM1_CH264

LCM_RESET

LCM_LEDLCM_DC

D12MI

All_KEY

NUC_RST#

D12MO

UART_RXD_B

Link1_VCC

VCC33

BUZZER

UART_TXD_B

SPI0_CS#SPI0_CLK

SPI0_DOSPI0_DI

M_Trigger2M_Trigger1


UART_Debug

Link2_VCC

LC

M_

VC

C_

Ctr

l

M_Trigger4M_Trigger3 M_Trigger4

M_Trigger3

Q38550

1

23

Link3_VCC

UA

RT

_T

XD

_C

Page_DownPage_Up

R5 0

VCC33

All Button Control

Link4_VCC UA

RT

_R

XD

_C

D12MO

X1

12MHz

D12MI

R433

C420p

C620p

Crystal

LCM_LED

SPI0_DO

SPI0_CS#SPI0_CLKSPI0_DI

LCM_DCLCM_RESET

M0_RXDM0_TXD

LCM_LEDLCM_RESET

LCM_SPI_MISOLCM_SPI_CLK

LCM_DC

LCM_SPI_SS

LCM_SPI_MOSI

UART_RXD_AUART_TXD_AUART_TXD_A

UART_RXD_A

VCC33Pow er on

R9 330LED1

GREEN(DIP)

UART_TXD_BUART_RXD_B

UART_RXD_BUART_TXD_B

SW1

RKSP86-N-A0-00(Red)

A1

B2

B3

A4

VCC33

R110K

All_KEY

Tit le

Size Docum ent Num ber Rev

Dat e: Sheet of

<Doc> V1.0

M0518SD2AE

A4

1 7Friday , October 28, 2016

UA

RT

_T

XD

_D

UA

RT

_R

XD

_D

UART_RXD_CUART_TXD_CUART_TXD_C

UART_RXD_C

VCC33

ICE_RST

NUC_RST#

R210K

Reset

C110uF/10V

12

M_RST# NUC_RST#

C80.1uC9

1uF/16V

12

VCC33

Nu-Link-Gang

Dec. 23, 2019 Page 28 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

6.2 Power and Connection Schematic

VCC33

5VCC

J27 Hole (NC)

1

J29 Hole (NC)

1

J28 Hole (NC)

1

J30 Hole (NC)

1

Fail4Pass4Fail4

Pass4

J31 Hole (NC)

1

J20

ADuM1400

12345678

161514131211109

Switch

All_KEY

5VCC

JP30

choke

1 2

VCC33U3AMS1117 3.3V

IN3

GN

D1

OU

T2

OU

T4

POWER

All_KEY

Trigger1_4PTrigger2_4P

Pass3

Pass2Fail3

Fail2Pass1

Pass4Fail4

Fail1

All_KEY KEY1KEY2

KEY4KEY3Trigger4_4P

Trigger3_4P

JP2

SS12SDP2 (Switch)

123

M_Trigger2

M_Trigger1

3VCC_4

3VCC_4

M_Trigger3

M_Trigger4

J32 Hole (NC)

1

C5110uF/10V

12

J33 Hole (NC)

1

U21

SN74LS157

Select1

1A2

1B3

1Y4

2A5

2B6

2Y7

88

3Y93B103A114Y124B134A14Strobe15VCC16

J34 Hole (NC)

1

J35 Hole (NC)

1

5VCC

ADuM1400 隔離器

J1 DC5V(2.0mm)

1

3 2

DC5V I nput

C1010uF/10V

12

L16

FERRITE BEAD

KEY1

V1MC7805CT(TO-220)

IN1

OUT3

GN

D2

GN

D4

Power_GND

螺絲孔

KEY2

外部Trigger

M_Trigger1

M_Trigger3M_Trigger2M_Trigger1

M_Trigger4M_Trigger3M_Trigger2

KEY1M_Trigger4

KEY2KEY1

KEY4KEY3KEY2

KEY4KEY3

BUSY2Trigger2_4P

BUSY1Trigger1_4P

BUSY4Trigger4_4P

Trigger3_4PBUSY3

J22

HEADER 10X2

13579

1113151719

2468101214161820

L31 FERRITE BEAD

KEY3

單次/同時燒錄切換器

VCC_Other

KEY4

SW2

PushButton(Lock)

NC1NO2CM3

NC4

NO5

CM6

GND7

GND8

Trigger2_4PTrigger1_4PR90 10K

Trigger4_4PTrigger3_4PR92 10K

R91 10K

R93 10K

Pass2Fail2

Fail2Pass2

R94 0

J23 Hole (NC)

1

5VCC

C110.1u

All_KEYAll_KEY

C130.1u

Tit le


Dat e: Sheet of

<Doc> V1.2

Power & Connect

A4

2 7Sunday , December 04, 2016

JP21

NC

12

J9

NC

12

C1210uF/10V

12

Pass1Fail1Pass1

Fail1

JP31

choke

1 2

Pass3Fail3Pass3

Fail3

VCC_Other

Power_VDD

Trigger1_4P

Trigger4_4PTrigger3_4PTrigger2_4P

J26 Hole (NC)

1

All_KEY

Nu-Link-Gang

Dec. 23, 2019 Page 29 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

6.3 #1 NuLink Schematic

BUSY1

RP1

8P4R-330

1 23 45 67 8

C3410uF/10V

12

JP25

NC

123

UART_RXD_AUART_TXD_A

UART_RXD_AUART_TXD_A

TICE_CLK1TICE_RST1

R780

NuLink power for main chip ADC

CB2

0.1u

R16 330

R15 330Pass1

LED3

RED(DIP)

LED2

GREEN(DIP)

Fail1

3VCC_1

ICP Interface

UART_RXD_A

J3

mini USB 5pin

GND5

NC4

DP3

DM2

VCC1

SHIELD6SHIELD7SHIELD8SHIELD9

TICERST

TICERST

TICECLK

NuGang top board connect

3VCC_1

ADAVSS

ICE_CLKICE_DAT

U4

NUC12SRE3DE

PA0/ADC044PA1/ADC145PA2/ADC246PA3/ADC347PA4/ADC448INT0/PB14

1

CPO1/PB132

CPO0/PB123

VB

US

17

VD

D33

18

D-

19

D+

20

PB

0/R

X0

21

PB

1/T

X0

22

PB

2/R

TS

023

PB

3/C

TS

024

PC

2/S

DI0

026

PC

1/S

PC

LK

027

PC

0/S

S00

28

PC11/SDO1033PC10/SDI1034PC9/SPCLK135PC8/SS1036PA15/PWM337PA14/PWM238PA13/PWM139

X32I4

X32O5

I2C1SCL/PA116

I2C0SDA/PA89

I2C1SDA/PA107

I2C0SCL/PA98

RX1/PB410

TX1/PB511

RTS1/PB612

CTS1/PB713

PC

3/S

DO

00

25

AVSS43

ICE_CK42

ICE_DAT41

PA12/PWM040

LDO14

VSS16 VDD15

AD

C/P

A5

49

AD

C6/P

A6

50

AD

C7/P

A7

51

AV

DD

52

CP

N0/P

C7

53

CP

P0/P

C6

54

CP

N1/P

C15

55

CP

P1/P

C14

56

INT

1/P

B15

57

XT

1_O

ut

58

XT

1_In

59

/RE

SE

T60

VS

S1

61

VD

D1

62

PV

SS

63

ST

AD

C/T

M0/P

B8

64

PE

529

PB

11/T

M3

30

PB

10/S

S01/T

M2

31

PB

9/S

S11/T

M1

32

R821K

R831K

C461u

Link1_VCC

ICPLED

BUSY1IDLE1

M_Trigger1

ICELED

3VCC_1

JP20

3 pin DIP (Switch)

123

654

12M_O C14 20p

X3

12MHz

C15 20p

UART_TXD_A

12M_I

TICE_CLK1TICE_CLK1

UA

RT

_R

XD

_A

UA

RT

_T

XD

_A

DO_DIR1VCOM_En

SP

I0_D

IS

PI0

_C

LK

SP

I0_C

S#

SP

I0_D

O

VBUSUSBVBUS1

USB_D-USB_D+

C42 10uF/10V

12

VCC_1

12

BUSY1 GREEN(SMD)


KEY1KEY1

U5

W25Q32

SOIC-8P

CS#1

DO2

WP#3

GND4

DI5CLK6HOLD#7VCC8

3VCC_1

J12

NC

1

DI_DIR2

TICEDAT

3VCC_1

3V input only

SPI0_DI

JP5

NC

12345

M_Trigger1

3VCC_1

3VCC_1

ICE_DAT

ICE_RSTICE_CLK

Power

SPI0_CS#

SPI0_CLKSPI0_DO

DO_DIR1

TICECLKTICERST

SN74LVC2T45DCUR

ICEU1

SSOP-8

GND4 A23

VCCA1

DIR5

A12

B26B17VCCB8

TICE_DAT1

VCC_1

TICE_DAT1

NOTE:

DEBUG的電源可以不用接VCC_1

3VCC_1

SPI FLASH

12

IDLE1 RED(SMD)

12

ICP1 YELLOW(SMD)

12

ICE1 RED(SMD)

C3510uF/10V

12

U17RT9164A 1.8V

IN3

GN

D1

OU

T2

OU

T4

U12AMS1117 3.3V

IN3

GN

D1

OU

T2

OU

T4

RTCK1100K

RTDA1100K

RRSET1100K

L3 FERRITE BEAD

5VCC_1

R14 33

Fail1

BUSY1BUSY1

MCU and USB

L19 FERRITE BEAD

VCC_1

Pass1

R13 33

5VCC_1

R50 NC

R62 100

3VCC_1AVDD1

1.8VCC_1

SN74LVC2T45DCUR

ICEU2

SSOP-8

GND4 A23

VCCA1

DIR5

A12

B26B17VCCB8

Fail1

R63 100

JP3

ICE_HEADER 5X2 (簡易牛角)

1 23 45 67 89 10

R51 NC

NUC_RST#

3VCC_1

ICE_RST

5VCC_1

R52 NC

L20 FERRITE BEAD

L4 FERRITE BEAD

TICECLK

Reset

3VCC_1

TICERST

SW3

RKSP86-N-A0-00(YELLOW)

A1

B2

B3

A4

R1010K

3VCC_1

KEY1

R11 NC

VCOM_En

ADAVSS

JP4


1 23 45 67 89 10

R1210K

CB10.1u RTDA21K

TICEDAT

Link1_VCCLink1_VCC

USBVBUS1

C1810uF/10V

12

Fail1

M_RST# NUC_RST#

TICE_DAT1TICE_RST1TICE_CLK1

L5 FERRITE BEAD

3VCC_1

R64 100

Pass1

TICEDAT

Pass1

R740

VCC_1

IDLE1

ICPLED

ICELED

BUSY1

3VCC_1

Display

C17

1u

TICE_DAT1

12M

_I

DI_

DIR

212M

_O

NU

C_R

ST

#

PVSS

3VCC_1 AVDD1

Tit le


Dat e: Sheet of

<Doc> V1.2

Nu-Link1

A3


C1610uF/10V

12

5VCC

TICE_RST1TICE_RST1

Nu-Link-Gang

Dec. 23, 2019 Page 30 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L


L8 FERRITE BEAD

SN74LVC2T45DCUR

ICEU4

SSOP-8

GND4 A23

VCCA1

DIR5

A12

B26B17VCCB8

R22 330

R23 330Fail2

Pass2

LED5

RED(DIP)

LED4

GREEN(DIP)

Pass2Fail2

3VCC_2

Tit le


Dat e: Sheet of

<Doc> V1.2

Nu-Link2

A3


SP

I0_D

O

DO_DIR1VCOM_En

UA

RT

_R

XD

_B

UA

RT

_T

XD

_B

ICELEDICPLED

BUSY2IDLE1

M_Trigger2

USB_D-USB_D+

VBUS

SP

I0_D

IS

PI0

_C

LK

SP

I0_C

S#

TICECLKTICERST

DI_

DIR

2

TICEDAT

ICE_CLKICE_DAT

TICERST

12M_O

12M

_O

NU

C_R

ST

#

PVSS

12M

_I

M_RST# NUC_RST#

ICE_RST

NUC_RST#

12M_I

ICE_CLK

SPI0_DI

DI_DIR2

TICEDAT

TICERSTDO_DIR1

TICECLK

SPI0_CS#

SPI0_CLKSPI0_DO

ICE_DAT

ICE_RST

TICE_CLK2TICE_RST2

M_Trigger2

Pass2

Pass2Fail2

TICE_DAT2

VCOM_En

C2110uF/10V

12

RRSET2100K

C20 20p

J4

mini USB 5pin

GND5

NC4

DP3

DM2

VCC1


JP8

NC

12345

L7 FERRITE BEAD

L6 FERRITE BEAD

RTDA41KJP7


1 23 45 67 89 10

C2310uF/10V

12

RTCK2100K

R18 NC

CB30.1u

X4

12MHz

C19 20p

RTDA3100K

C22

1u

CB4

0.1u

R1910K

U6

NUC12SRE3DE


1

CPO1/PB132

CPO0/PB123

VB

US

17

VD

D33

18

D-

19

D+

20

PB

0/R

X0

21

PB

1/T

X0

22

PB

2/R

TS

023

PB

3/C

TS

024

PC

2/S

DI0

026

PC

1/S

PC

LK

027

PC

0/S

S00

28


X32I4

X32O5

I2C1SCL/PA116

I2C0SDA/PA89

I2C1SDA/PA107

I2C0SCL/PA98

RX1/PB410

TX1/PB511

RTS1/PB612

CTS1/PB713

PC

3/S

DO

00

25

AVSS43

ICE_CK42

ICE_DAT41

PA12/PWM040

LDO14

VSS16 VDD15

AD

C/P

A5

49

AD

C6/P

A6

50

AD

C7/P

A7

51

AV

DD

52

CP

N0/P

C7

53

CP

P0/P

C6

54

CP

N1/P

C15

55

CP

P1/P

C14

56

INT

1/P

B15

57

XT

1_O

ut

58

XT

1_In

59

/RE

SE

T60

VS

S1

61

VD

D1

62

PV

SS

63

ST

AD

C/T

M0/P

B8

64

PE

529

PB

11/T

M3

30

PB

10/S

S01/T

M2

31

PB

9/S

S11/T

M1

32

U7

W25Q32

SOIC-8P

CS#1

DO2

WP#3

GND4

DI5CLK6HOLD#7VCC8

3VCC_2

USBVBUS2

3VCC_2

ADAVSS

3VCC_2 AVDD2

3VCC_23VCC_2

3VCC_2

3VCC_2

3VCC_2

3VCC_2

VCC_2

VCC_2

AVDD2 3VCC_2

ADAVSS

TICE_DAT2

TICE_CLK2TICE_RST2

MCU and USB

M_Trigger2

NuGang top board connectICP Interface

SPI FLASH

NOTE:

DEBUG的電源可以不用接3V input only

Reset

R790

R21 33

KEY2

R1710K

3VCC_2

SW4


A1

B2

B3

A4

BUSY2

TICE_RST2R65 100 TICE_CLK2

R67 100

R66 100

TICE_DAT2

R841K

R851K

Link2_VCC

C471u

J13

NC

1

C3610uF/10V

12

C3710uF/10V

12

Power

U18RT9164A 1.8V

IN3

GN

D1

OU

T2

OU

T4

L23 FERRITE BEAD

U13AMS1117 3.3V

IN3

GN

D1

OU

T2

OU

T4

1.8VCC_2

5VCC_2

L24 FERRITE BEAD

5VCC_2

VCC_2

3VCC_2

JP6


1 23 45 67 89 10

R750

VCC_2

5VCC

KEY2KEY2

C43 10uF/10V

12

JP22

3 pin DIP (Switch)

123

654

Fail2

BUSY2BUSY2

JP26

NC

123

UART_TXD_BUART_RXD_B

UART_RXD_B

5VCC_2

UART_RXD_BUART_TXD_B

UART_TXD_B


R20 33

VCC_2

RP2

8P4R-330

1 23 45 67 8

12

BUSY2 GREEN(SMD)

12

IDLE2 RED(SMD)

12

ICE2 RED(SMD)

12

ICP2 YELLOW(SMD)

IDLE1

ICPLED

BUSY2

ICELED

Display

3VCC_2

R54 NCR53 NC

R55 NC

TICERSTTICECLK


TICEDAT

Link2_VCCLink2_VCC

USBVBUS2

SN74LVC2T45DCUR

ICEU3

SSOP-8

GND4 A23

VCCA1

DIR5

A12

B26B17VCCB8

3VCC_2

Nu-Link-Gang

Dec. 23, 2019 Page 31 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L


R27 33

RP3

8P4R-330

1 23 45 67 8

12

BUSY3 GREEN(SMD)

12

ICP3 YELLOW(SMD)

12

IDLE3 RED(SMD)

12

ICE3 RED(SMD)

ICPLED

ICELED

IDLE1

BUSY3

Display

3VCC_3

SW5


A1

B2

B3

A4

3VCC_3

KEY3

R2410K

3VCC_3

BUSY3

Fail3

Link3_VCCLink3_VCC

R30 330

R29 330Pass3

LED7

RED(DIP)

LED6

GREEN(DIP)

Fail3

3VCC_3

UART_TXD_CUART_RXD_C

UART_RXD_CUART_TXD_C

Tit le


Dat e: Sheet of

<Doc> V1.2

Nu-Link3

A3


ICPLED

BUSY3IDLE1

M_Trigger3

VBUS

SP

I0_D

IS

PI0

_C

LK

SP

I0_C

S#

SP

I0_D

O

DO_DIR1VCOM_En

UA

RT

_R

XD

_C

UA

RT

_T

XD

_C

ICELED

USB_D-USB_D+

TICERST

TICECLKTICERST

SN74LVC2T45DCUR

ICEU5

SSOP-8

GND4 A23

VCCA1

DIR5

A12

B26B17VCCB8

PVSS

12M

_I

DI_

DIR

2

TICEDAT

ICE_CLKICE_DAT

12M_I

12M_O

12M

_O

NU

C_R

ST

#

M_RST# NUC_RST#

ICE_RST

NUC_RST#

DI_DIR2

TICEDAT

ICE_DAT

ICE_RSTICE_CLK

SPI0_DI

TICERSTDO_DIR1

TICECLK

SPI0_CS#

SPI0_CLKSPI0_DO

Pass3Fail3

TICE_DAT3

TICE_CLK3TICE_RST3

VCOM_En

M_Trigger3

Pass3

C2610uF/10V

12

RRSET3100K

C25 20p

JP11

NC

12345

L9 FERRITE BEAD

RTDA61K

L10 FERRITE BEAD

JP10


1 23 45 67 89 10

RTCK3100K

CB50.1u

C2810uF/10V

12

R25 NC

X5

12MHz

C24 20p

C27

1u

RTDA5100K

CB6

0.1u

R2610K

SN74LVC2T45DCUR

ICEU6

SSOP-8

GND4 A23

VCCA1

DIR5

A12

B26B17VCCB8USBVBUS3

U8

NUC12SRE3DE


1

CPO1/PB132

CPO0/PB123

VB

US

17

VD

D33

18

D-

19

D+

20

PB

0/R

X0

21

PB

1/T

X0

22

PB

2/R

TS

023

PB

3/C

TS

024

PC

2/S

DI0

026

PC

1/S

PC

LK

027

PC

0/S

S00

28


X32I4

X32O5

I2C1SCL/PA116

I2C0SDA/PA89

I2C1SDA/PA107

I2C0SCL/PA98

RX1/PB410

TX1/PB511

RTS1/PB612

CTS1/PB713

PC

3/S

DO

00

25

AVSS43

ICE_CK42

ICE_DAT41

PA12/PWM040

LDO14

VSS16 VDD15

AD

C/P

A5

49

AD

C6/P

A6

50

AD

C7/P

A7

51

AV

DD

52

CP

N0/P

C7

53

CP

P0/P

C6

54

CP

N1/P

C15

55

CP

P1/P

C14

56

INT

1/P

B15

57

XT

1_O

ut

58

XT

1_In

59

/RE

SE

T60

VS

S1

61

VD

D1

62

PV

SS

63

ST

AD

C/T

M0/P

B8

64

PE

529

PB

11/T

M3

30

PB

10/S

S01/T

M2

31

PB

9/S

S11/T

M1

32

U9

W25Q32

SOIC-8P

CS#1

DO2

WP#3

GND4

DI5CLK6HOLD#7VCC8

3VCC_3

USBVBUS3

AVDD3

3VCC_3

ADAVSS

3VCC_3

3VCC_3

3VCC_33VCC_3VCC_3

3VCC_3

3VCC_3

3VCC_3

VCC_3

3VCC_3AVDD3

ADAVSS

TICE_RST3

R57 NCR56 NC

TICE_DAT3

TICE_CLK3

R58 NC

NOTE:


Reset

MCU and USB

M_Trigger3

TICERSTTICECLK

NuGang top board connectICP Interface

SPI FLASH


TICEDAT

JP9


1 23 45 67 89 10

J5

mini USB 5pin

GND5

NC4

DP3

DM2

VCC1


Pass3Fail3

C3810uF/10V

12

C3910uF/10V

12

Power

U19RT9164A 1.8V

IN3

GN

D1

OU

T2

OU

T4

U14AMS1117 3.3V

IN3

GN

D1

OU

T2

OU

T4

L26 FERRITE BEAD 1.8VCC_3

5VCC_3

L27 FERRITE BEAD

5VCC_3

3VCC_3

VCC_3

R760

5VCC

L11 FERRITE BEADR800

J14

NC

1

KEY3KEY3


TICE_CLK3TICE_RST3R69 100

R68 100

R70 100 TICE_DAT3

R871K

R861K

Link3_VCC

C481u

5VCC_3

BUSY3BUSY3

VCC_3

VCC_3

JP23

3 pin DIP (Switch)

123

654

JP27

NC

123

UART_TXD_CUART_RXD_C

R28 33

C44 10uF/10V

12

Nu-Link-Gang

Dec. 23, 2019 Page 32 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L


VCC_4

BUSY4BUSY4

R881K

R891K

C491u

Link4_VCC

Fail4

5VCC_4

JP24

3 pin DIP (Switch)

123

654

RP4

8P4R-330

1 23 45 67 8

12

IDLE4 RED(SMD)

12

BUSY4 GREEN(SMD)

12

ICE4 RED(SMD)

12

ICP4 YELLOW(SMD)

IDLE1

ICPLED

BUSY4

ICELED

Display

3VCC_4

VCC_4

USBVBUS4

3VCC_4

UART_TXD_DUART_RXD_D

JP28

NC

123

L14 FERRITE BEAD

C45 10uF/10V

12

Tit le


Dat e: Sheet of

<Doc> V1.2

Nu-Link4

A3


VCOM_En

UA

RT

_R

XD

_D

UA

RT

_T

XD

_D

ICELEDICPLED

BUSY4IDLE1

M_Trigger4

USB_D-USB_D+

VBUS

SP

I0_D

IS

PI0

_C

LK

SP

I0_C

S#

SP

I0_D

O

DO_DIR1

TICERST

TICEDAT

ICE_CLKICE_DAT

TICERST

TICECLK

12M_O

12M

_O

NU

C_R

ST

#

PVSS

12M

_I

DI_

DIR

2

M_RST# NUC_RST#

ICE_RST

NUC_RST#

12M_I

SPI0_DI

DI_DIR2

TICEDAT

DO_DIR1

TICECLK

SPI0_CS#

SPI0_CLKSPI0_DO

ICE_DAT

ICE_RSTICE_CLKTICERST

M_Trigger4

Pass4

Pass4Fail4

TICE_DAT4

TICE_CLK4TICE_RST4

VCOM_En

RRSET4100K

C3110uF/10V

12

C30 20p

JP14

NC

12345

L13 FERRITE BEAD

L12 FERRITE BEAD

RTDA81KJP13


1 23 45 67 89 10

C3310uF/10V

12

RTCK4100K

R32 NC

CB70.1u

R59 NC

X6

12MHz

R60 NCTICERSTTICECLK

R61 NCTICE_DAT4TICE_RST4TICE_CLK4

TICEDAT

C29 20p

RTDA7100K

C32

1u

CB8

0.1u

R3310K

U10

NUC12SRE3DE


1

CPO1/PB132

CPO0/PB123

VB

US

17

VD

D33

18

D-

19

D+

20

PB

0/R

X0

21

PB

1/T

X0

22

PB

2/R

TS

023

PB

3/C

TS

024

PC

2/S

DI0

026

PC

1/S

PC

LK

027

PC

0/S

S00

28


X32I4

X32O5

I2C1SCL/PA116

I2C0SDA/PA89

I2C1SDA/PA107

I2C0SCL/PA98

RX1/PB410

TX1/PB511

RTS1/PB612

CTS1/PB713

PC

3/S

DO

00

25

AVSS43

ICE_CK42

ICE_DAT41

PA12/PWM040

LDO14

VSS16 VDD15

AD

C/P

A5

49

AD

C6/P

A6

50

AD

C7/P

A7

51

AV

DD

52

CP

N0/P

C7

53

CP

P0/P

C6

54

CP

N1/P

C15

55

CP

P1/P

C14

56

INT

1/P

B15

57

XT

1_O

ut

58

XT

1_In

59

/RE

SE

T60

VS

S1

61

VD

D1

62

PV

SS

63

ST

AD

C/T

M0/P

B8

64

PE

529

PB

11/T

M3

30

PB

10/S

S01/T

M2

31

PB

9/S

S11/T

M1

32

R37 330

R36 330

U11

W25Q32

SOIC-8P

CS#1

DO2

WP#3

GND4

DI5CLK6HOLD#7VCC8

3VCC_4

ADAVSS

USBVBUS4

3VCC_4 AVDD4

3VCC_4

3VCC_4

3VCC_4

3VCC_4 3VCC_4

VCC_4

VCC_4

3VCC_4

3VCC_4

3VCC_4AVDD4

ADAVSS

TICE_DAT4

TICE_CLK4TICE_RST4

M_Trigger4

ICP Interface

SPI FLASH

NOTE:


ResetMCU and USB

NuGang top board connect

Link4_VCCLink4_VCC

Fail4

Pass4 LED8

GREEN(DIP)

LED9

RED(DIP)

SN74LVC2T45DCUR

ICEU7

SSOP-8

GND4 A23

VCCA1

DIR5

A12

B26B17VCCB8

JP12


1 23 45 67 89 10

SN74LVC2T45DCUR

ICEU8

SSOP-8

GND4 A23

VCCA1

DIR5

A12

B26B17VCCB8

C4010uF/10V

12

C4110uF/10V

12

Power

U20RT9164A 1.8V

IN3

GN

D1

OU

T2

OU

T4

U15AMS1117 3.3V

IN3

GN

D1

OU

T2

OU

T4

L29 FERRITE BEAD 1.8VCC_4

5VCC_4

L30 FERRITE BEAD

5VCC_4

3VCC_4

VCC_4

5VCC

R770

3VCC_4

SW6


A1

B2

B3

A4KEY4

R3110K

3VCC_4

J6

mini USB 5pin

GND5

NC4

DP3

DM2

VCC1


TICE_CLK4TICE_RST4R72 100

R71 100

R73 100 TICE_DAT4


KEY4KEY4

BUSY4

J15

NC

1

Pass4Fail4

R810

UART_RXD_DUART_TXD_DUART_RXD_D

UART_TXD_D

R35 33R34 33

Nu-Link-Gang

Dec. 23, 2019 Page 33 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

6.7 LCD Display Schematic

J11

HEADER 10(2.0母座)

12345678910

LCM_LED

SPI0_DO

SPI0_CS#SPI0_CLKSPI0_DI

LCM_DCLCM_RESET LCM_LED

LCM_RESET

LCM_SPI_MISOLCM_SPI_CLK

LCM_DC

LCM_SPI_SS

LCM_SPI_MOSI

VCC33

Tit le


Dat e: Sheet of

<Doc> V1.2

TFT LCD (SPI)

A4

7 7Monday , December 05, 2016

320*240 TFT LCD

S8050

1

Base

3

Collector

Si2301BDS

2

Source

3

Drain

1

Gate2

Emitter

LCM_LED

J10

HEADER 10(2.0母座)

12345678910

LCM_DCLCM_SPI_SSLCM_SPI_MOSILCM_SPI_MISOLCM_VCC_Ctrl

LCM_RESETLCM_SPI_CLK

VCC33

Page_Up

B1

Big Buttom

BULE_BUTTOM

100K 改10K

R3910K

VCC33

Page_Down

B2

Big Buttom

BULE_BUTTOM

R4010K

LCM_VCC_CtrlLCM_VCC_Ctrl

PC6=RESET

PC9=CLKPC15=DCPC8=SSPC11MOSIPC10=MISOPA12=LCD_CtrlPC14=LED

Page_Up

Page_Down

Nu-Link-Gang

Dec. 23, 2019 Page 34 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

7 TROUBLESHOOTING

7.1 Pop-up Warning Message When Programming NUC505 Series

When pop-up warning message shows as Figure 7-1 while programming NUC505 series, please check all four programming units’ IC mode is set to Mode 1 on the Nuvoton NUC505 ICP Gang Adapter and press Reset button. If the warning message still pop-up, please check the NUC505 chip is placed currectly.

Figure 7-1 Pop-up Warning Message

7.2 Nu-Link-Gang Firmware Update

The Jp15 interface is to update the Nu-Link-Gang firmware provided by Nuvoton.

Note: When update the Nu-Link-Gang firmware, please update the programming units firmware to the lastest version as well.

7.3 Programming Unit Firmware Update

It is recommended to update the ICP Programming Tool to the lastest version. Connects the programming unit to ICP Programming Tool as section 3.3.1 and 3.3.2, the ICP Programming Tool will check the programming unit firmware version. The warning message as Figure 7-2 pops up when ICP Programming Tool starts updating programming unit. By following the tips shown by pop-up windows as Figure 7-2 and Figure 7-3, users can update the programming units’ firmware.

Note 1: When update the programming units firmware, please update the Nu-Link-Gang firmware to the lastest version as well.

Note 2: Please update all four programming units firmware to the same version.

Nu-Link-Gang

Dec. 23, 2019 Page 35 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

Figure 7-2 Pop-up Warning Message

Figure 7-3 Programming Unit Firmware Update

Nu-Link-Gang

Dec. 23, 2019 Page 36 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

8 REVISION HISTORY

Date Revision Description

2019.12.23 1.00 1. Preliminary version.

Nu-Link-Gang

Dec. 23, 2019 Page 37 of 37 Rev 1.00

NU

-LIN

K-G

AN

G U

SE

R M

AN

UA

L

Important Notice

Nuvoton Products are neither intended nor warranted for usage in systems or equipment, any malfunction or failure of which may cause loss of human life, bodily injury or severe property damage. Such applications are deemed, “Insecure Usage”.

Insecure usage includes, but is not limited to: equipment for surgical implementation, atomic energy control instruments, airplane or spaceship instruments, the control or operation of dynamic, brake or safety systems designed for vehicular use, traffic signal instruments, all types of safety devices, and other applications intended to support or sustain life.

All Insecure Usage shall be made at customer’s risk, and in the event that third parties lay claims to Nuvoton as a result of customer’s Insecure Usage, customer shall indemnify the damages and liabilities thus incurred by Nuvoton.

Documents

NuMicro Family Nu-Link-Gang User Manual · 2019-12-23 · Power1 Power2 Power3 Power4 Adapter Board Connector Slot1 Slot2 Slot3 Slot4 Single-start Button Start1 Start2 Start3 Start4