Upload
others
View
9
Download
0
Embed Size (px)
Citation preview
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 1 of 42
National Standards Authority of Ireland
NSAI Petroleum Exploration and Extraction Technical Standards
Committee recommended standards selection policy
Issue date: 2013-09-09
The information in this document is correct as July 2013. Standards are continuously being
revised and developed and the editions of the Standards listed are subject to routine
change.
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 2 of 42
Foreword
In response to a request from the Commission of Energy Regulation (CER) the NSAI Petroleum
Exploration and Extraction Technical Standards Committee (PEETSC) has developed this
recommended Standards selection policy document to be applied to petroleum exploration and
extraction activities.
This policy recommendation may assist in fulfilling the CER's obligation to consult NSAI with regard
to the following provisions of the Petroleum (Exploration and Extraction) Safety Act 2010, namely
Sections:
13 H (2) (a),
13 L (2) (a) (i),
13 L (3) (c) and
13 L (3) (d).
Scope
This recommendation sets out a policy that can be applied to petroleum undertakings when
selecting suitable standards to be applied for any petroleum activity licensed under the above Act.
It recognises the extensive number of Standards available and the fact that many new and revised
standards are published every year. It also recognises that, given the nature of the activity, there
cannot be an exhaustive list of suitable standards.
This document provides a list of recommended standards that can be to applied petroleum
exploration and extraction activities.
Legislation
Standards emanating from Standards bodies are not, in themselves, mandatory and only achieve a
mandatory status when referenced in legal instruments.
In all cases legislation takes precedence over any voluntary standard.
When projects to be funded from public funds are to be awarded, those responsible should be
aware of any obligations they may have under public procurement regulations/Directives. For
guidance on this matter the National Procurement Service should be consulted:
http://www.procurement.ie/publications/public-procurement-guidelines-competitive-process
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 3 of 42
Selection of suitable standards
When selecting suitable specifications for petroleum exploration and extraction activities they
should be selected in order of preference:
1. Irish Standards Specifications (I.S.),
2. NSAI adoptions of European and International Standards,
3. International Standards,
These publications specify minimum requirements for the relevant activity.
In the event that a particular activity, covered by 1 to 3 is addressed more comprehensively in
another publication, undertakings may apply that publication provided that any requirements
contained in 1 to 3 are also met.
In the event that a particular activity is not covered by the above, undertakings can choose to use
publications such as the following:
a. Standards from other National Standards Bodies,
b. Other NSAI publications,
c. Standards from Classification Societies (e.g. Bureau Veritas),
d. Publications from suitable associations (e.g. API).
Rigs and other equipment designed for International use
The PEETSC recognises that the building of equipment such as oil rigs is a truly international activity.
Most rigs are built to meet the expectations of operators active in other national and international
waters. Given this, the selection of standards used to construct/build such equipment cannot,
necessarily follow this policy. However the PEETSC also recognises that such equipment is almost
always built to classification society rules in order to operate to the satisfaction of authorities in
other jurisdictions.
List of suitable standards
The following list is a snapshot (correct on the date of compilation) of identified suitable standards,
in respect to 1 to 3 above, for petroleum exploration and extraction activities. It does not purport to
be a comprehensive list but is a guide to the reader of the types of standards NSAI has recognised as
suitable. This list will be updated from time to time but no less than every two years.
A reference list of publications covering drilling, well construction and well operations is available
from:
http://www.ogp.org.uk/publications/wells-committee/wecstandards/
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 4 of 42
Standards in the Oil & Gas industry
The standards listed in this document are recommended as suitable for application in
Ireland. This list is not exhaustive.
Introduction
The majority of Standards referenced in this document have been developed and published by the
International Standards Organisation, ISO, under the Technical Committee ISO/TC 67. Where these
ISO Standards can be adopted by Europe directly without modification then are adopted and
published by the European Committee for Standardisation (CEN) under Technical Committee
CEN/TC 12. Where a modification is required to an ISO Standard CEN/TC 12 publishes the ISO
Standard as a European Standard with its own number and develops the European Standard with
the specific European requirements.
ISO Standards are not automatically adopted as Irish Standards.
European Standards are automatically adopted as Irish Standards.
ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural
gas industries
CEN/TC 12, Materials, equipment and offshore structures for petroleum, petrochemical and natural
gas industries
For standards relating to Explosive atmospheres go to ETCI/TC 6 which mirrors the work of:
CENELEC TC 31 - Electrical apparatus for potentially explosive atmospheres, and
IEC TC 31 - Equipment for explosive atmospheres
Explanation of Standard designations
A Standard is a document that provides requirements, specifications, guidelines or characteristics
that can be used consistently to ensure that materials, products, processes and services are fit for
their purpose.
Typical Standard references
I.S. 123 Irish Standard developed and published by NSAI
S.R. 123 Irish Standard Recommendation published by NSAI
EN 12345 European Standard published by CEN/CENELEC
ISO 12345 International Standard published by ISO
IEC 60125 International Standard published by IEC
I.S. EN 12345 European Standard adopted as an Irish Standard
EN ISO 12345 ISO Standard adopted as a European Standard
I.S. EN ISO 12345 European Standard adopted as an Irish Standard
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 5 of 42
I.S. ISO 12345 ISO Standard adopted as an Irish Standard
A Technical Specification is a document for which there is the future possibility of agreement on a
European Standard, but for which at present:
the required support for approval as a Standard cannot be obtained,
there is doubt on whether consensus has been achieved,
the subject matter is still under technical development, or
there is another reason precluding immediate publication as a Standard.
A Technical Specification is not allowed to conflict with an existing European Standard.
Typical Technical Specification references
CEN/TS 12345 Technical Specification published by CEN
ISO/TS 12345 Technical Specification published by ISO
CEN ISO/TS 12345 ISO Technical Specification adopted as a European Technical Specification
S.R. CEN ISO/TS 12345 European Technical Specification adopted as an Irish Standard Recommendation
A Technical Report is a document containing informative material not suitable to be published as a
Standard or a Technical Specification. A TR can include, for example, data obtained from a survey
carried out among the national members, data on work in other organizations or data on the state of
the art in relation to national standards on a particular subject.
Typical Technical Report references
CEN/TR 12345 Technical Report published by CEN
S.R. CEN/TR 12345 CEN Technical Report adopted as an Irish Standard Recommendation
ISO/TR 12345 Technical Report published by ISO
CEN ISO/TR 12345 ISO Technical Report adopted as a European Technical Report
S.R. CEN ISO/TR 12345 European Technical Report adopted as an Irish Standard Recommendation
List of Irish National Standards and International Standard for the Oilfield
The information in the following tables is correct as of 13th September 2012. Standards are
continuously being revised and developed and the edition of the Standards listed are subject to
routine change.
The list of Standards has been separated into 7 sections. Standards can be used in the various
sections as appropriate.
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 6 of 42
Key:
1 Down hole
2 Subsea drilling and production equipment
3 Surface drilling, production and processing equipment and systems
4 Offshore structures (Semi submercibles)
5 Offshore structures (Platforms and jackets)
6 Pipeline transportation systems
7 Onshore processing
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 7 of 42
1 Down hole
Standards listed are from:
ISO/TC 67/SC 4 – Drilling and production equipment
ISO TC 67/SC 5 - Casing, tubing and drill pipe
Standard Number Standard Title
S.R. CEN ISO/TR 10400:2011 Petroleum and natural gas industries - Equations and calculations for the properties of casing, tubing, drill pipe and line pipe used as casing or tubing (ISO/TR 10400:2007)
I.S. EN ISO 10405:2006 Petroleum and natural gas industries - Care and use of casing and tubing (ISO 10405:2006)
ISO 10407:1993 Petroleum and natural gas industries -- Drilling and production equipment -- Drill stem design and operating limits
I.S. EN ISO 10407-2:2008 Petroleum and natural gas industries - Rotary drilling equipment - Part 2: Inspection and classification of used drill stem elements (ISO 10407-2:2008)
I.S. EN ISO 10414-1:2008 Petroleum and natural gas industries - Field testing of drilling fluids - Part 1: Water-based fluids (ISO 10414-1:2008)
I.S. EN ISO 10414-2:2011 Petroleum and natural gas industries - Field testing of drilling fluids - Part 2: Oil-based fluids (ISO 10414-2:2011)
I.S. EN ISO 10416:2009 Petroleum and natural gas industries - Drilling fluids - Laboratory testing (ISO 10416:2008)
I.S. EN ISO 10417:2004 Petroleum and natural gas industries - Subsurface safety valve systems - Design, installation, operation and redress (ISO 10417:2004)
I.S. EN ISO 10424-1:2004 Petroleum and natural gas industries - Rotary drilling equipment - Part 1: Rotary drill stem elements (ISO 10424-1:2004)
I.S. EN ISO 10424-2:2007 Petroleum and natural gas industries - Rotary drilling equipment - Part 2: Threading and gauging of rotary shouldered thread connections (ISO 10424-2:2007)
I.S. EN ISO 10426-1:2009 Petroleum and natural gas industries - Cements and materials for well cementing - Part 1: Specification (ISO 10426-1:2009)
I.S. EN ISO 10426-2:2003 Petroleum and natural gas industries - Cements and materials for well cementing - Part 2: Testing of well cements (ISO 10426-2:2003)
I.S. EN ISO 10426-3:2004 Petroleum and natural gas industries - Cements and materials for well cementing - Part 3: Testing of deepwater well cement formulations (ISO 10426-3:2003)
I.S. EN ISO 10426-4:2004 Petroleum and natural gas industries - Cements and materials for well cementing - Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure (ISO 10426-4:2004)
I.S. EN ISO 10426-5:2005 Petroleum and natural gas industries - Cements and materials for well cementing - Part 5: Determination of shrinkage and expansion of well cement formulations at atmospheric pressure (ISO 10426-5:2004)
I.S. EN ISO 10426-6:2008 Petroleum and natural gas industries - Cements and materials for well cementing - Part 6: Methods for determining the static gel strength of cement formulations (ISO 10426-6:2008)
I.S. EN ISO 10427-1:2001 Petroleum and natural gas industries - Casing centralizers - Part 1: Bow-spring casing centralizers (ISO 10427-1:2001)
I.S. EN ISO 10427-2:2004 Petroleum and natural gas industries - Equipment for well cementing - Part 2: Centralizer placement and stop-collar testing (ISO 10427-2:2004)
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 8 of 42
I.S. EN ISO 10427-3:2004 Petroleum and natural gas industries - Equipment for well cementing - Part 3: Performance testing of cementing float equipment (ISO 10427-3:2003)
I.S. EN ISO 10432:2004 Petroleum and natural gas industries - Downhole equipment - Subsurface safety valve equipment (ISO 10432:2004)
I.S. EN ISO 11960:2011 Petroleum and natural gas industries - Steel pipes for use as casing or tubing for wells (ISO 11960:2011)
I.S. EN ISO 11961:2008 Petroleum and natural gas industries - Steel drill pipe (ISO 11961:2008)
I.S. EN ISO 13500:2008 Petroleum and natural gas industries - Drilling fluid materials - Specifications and tests (ISO 13500:2008)
I.S. EN ISO 13501:2011 Petroleum and natural gas industries - Drilling fluids - Processing equipment evaluation (ISO 13501:2011)
I.S. EN ISO 13503-1:2011 Petroleum and natural gas industries - Completion fluids and materials - Part 1: Measurement of viscous properties of completion fluids (ISO 13503-1:2011)
I.S. EN ISO 13503-2:2006 Petroleum and natural gas industries - Completion fluids and materials - Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations (ISO 13503-2:2006)
I.S. EN ISO 13503-3:2005 Petroleum and natural gas industries - Completion fluids and materials - Part 3: Testing of heavy brines (ISO 13503-3:2005)
I.S. EN ISO 13503-4:2006 Petroleum and natural gas industries - Completion fluids and materials - Part 4: Procedure for measuring stimulation and gravel-pack fluid leakoff under static conditions (ISO 13503-4:2006)
I.S. EN ISO 13503-5:2006 Petroleum and natural gas industries - Completion fluids and materials - Part 5: Procedures for measuring the long-term conductivity of proppants (ISO 13503-5:2006)
I.S. EN ISO 13678:2012 Petroleum and natural gas industries - Evaluation and testing of thread compounds for use with casing, tubing, line pipe and drill stem elements (ISO 13678:2010)
I.S. EN ISO 13679:2006 Petroleum and natural gas industries - Procedures for testing casing and tubing connections (ISO 13679:2002)
I.S. EN ISO 13680:2010 Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions (ISO 13680:2010)
I.S. EN ISO 14310:2008 Petroleum and natural gas industries - Downhole equipment - Packers and bridge plugs (ISO 14310:2008)
I.S. EN ISO 15136-1:2009 Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 1: Pumps (ISO 15136-1:2009)
I.S. EN ISO 15136-2:2006 Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 2: Surface-drive systems (ISO 15136-2:2006)
I.S. EN ISO 15463:2003 Petroleum and natural gas industries - Field inspection of new casing, tubing and plain-end drill pipe (ISO 15463:2003)
I.S. EN ISO 15546:2011 Petroleum and natural gas industries - Aluminium alloy drill pipe (ISO 15546:2011)
I.S. EN ISO 16070:2005 Petroleum and natural gas industries - Downhole equipment - Lock mandrels and landing nipples (ISO 16070:2005)
I.S. EN ISO 17078-1:2004 Petroleum and natural gas industries - Drilling and production equipment - Part 1: Side-pocket mandrels (ISO 17078-1:2004)
I.S. EN ISO 17078-2:2007 Petroleum and natural gas industries - Drilling and production equipment - Part 2: Flow-control devices for side-pocket mandrels (ISO 17078-2:2007)
I.S. EN ISO 17078-3:2009 Petroleum and natural gas industries - Drilling and production equipment - Part 3: Running tools, pulling tools and kick-over tools and latches for side-pocket
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 9 of 42
mandrels (ISO 17078-3:2009)
I.S. EN ISO 17078-4:2010 Petroleum and natural gas industries - Drilling and production equipment - Part 4: Practices for side-pocket mandrels and related equipment (ISO 17078-4:2010)
ISO 17824:2009 Petroleum and natural gas industries -- Downhole equipment -- Sand screens
I.S. EN ISO 28781:2010 Petroleum and natural gas industries - Drilling and production equipment - Subsurface barrier valves and related equipment (ISO 28781:2010)
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 10 of 42
2 Subsea drilling and production equipment
Standards listed are from:
ISO/TC 67/SC 4 – Drilling and production equipment
Standard Number Standard Title
I.S. EN ISO 13628-1:2005 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 1: General requirements and recommendations (ISO 13628-1:2005)
I.S. EN ISO 13628-2:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 2: Unbonded flexible pipe systems for subsea and marine applications (ISO 13628-2:2006)
I.S. EN ISO 13628-3:2000 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 3: Through flowline (TFL) systems (ISO 13628-3:2000)
I.S. EN ISO 13628-4:2010 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 4: Subsea wellhead and tree equipment (ISO 13628-4:2010)
I.S. EN ISO 13628-5:2009 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 5: Subsea umbilicals (ISO 13628-5:2009)
I.S. EN ISO 13628-6:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 6: Subsea production control systems (ISO 13628-6:2006)
I.S. EN ISO 13628-7:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 7: Completion/workover riser systems (ISO 13628-7:2005)
I.S. EN ISO 13628-8:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 8: Remotely Operated Vehicle (ROV) interfaces on subsea production systems (ISO 13628-8:2002)
I.S. EN ISO 13628-9:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 9: Remotely Operated Tool (ROT) intervention systems (ISO 13628-9:2000)
I.S. EN ISO 13628-10:2006 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 10: Specification for bonded flexible pipe (ISO 13628-10:2006)
I.S. EN ISO 13628-11:2008 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 11: Flexible pipe systems for subsea and marine applications (ISO 13628-11:2007)
I.S. EN ISO 13628-15:2011 Petroleum and natural gas industries - Design and operation of subsea production systems - Part 15: Subsea structures and manifolds (ISO 13628-15:2011)
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 11 of 42
3 Surface drilling, production and processing equipment and systems
Standards listed are from:
ISO/TC 67
ISO/TC 67/SC 4 – Drilling and production equipment
ISO TC 67/SC 6 - Processing equipment and systems
Standard Number Standard Title
I.S. EN ISO 10418:2003 Petroleum and natural gas industries - Offshore production installations - Basic surface process safety systems (ISO 10418:2003)
I.S. EN ISO 10423:2009 Petroleum and natural gas industries - Drilling and production equipment - Wellhead and christmas tree equipment (ISO 10423:2009)
I.S. EN ISO 13533:2001 Petroleum and natural gas industries - Drilling and production equipment - Drill-through equipment (ISO 13533:2001)
I.S. EN ISO 13534:2000 Petroleum and natural gas industries - Drilling and production equipment - Inspection, maintenance, repair and remanufacture of hoisting equipment (ISO 13534:2000)
I.S. EN ISO 13535:2000 Petroleum and natural gas industries - Drilling and production equipment - Hoisting equipment (ISO 13535:2000)
I.S. EN ISO 13626:2004 Petroleum and natural gas industries - Drilling and production equipment - Drilling and well-servicing structures (ISO 13626:2003)
I.S. EN ISO 13702:1999 Petroleum and natural gas industries - Control and migration of fires and explosions on offshore production installations - Requirements and guidelines (ISO 13702:1999)
I.S. EN ISO 13703:2000 Petroleum and natural gas industries - Design and installation of piping systems on offshore production platforms (ISO 13703:2000)
I.S. EN ISO 14224:2006 Petroleum, petrochemical and natural gas industries - Collection and exchange of reliability and maintenance data for equipment (ISO 14224:2006)
I.S. EN ISO 14692-1:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 1: Vocabulary, symbols, applications and materials (ISO 14692-1:2002)
I.S. EN ISO 14692-2:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2002)
I.S. EN ISO 14692-3:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 3: System design (ISO 14692-3:2002)
I.S. EN ISO 14692-4:2002 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation (ISO 14692-4:2002)
I.S. EN ISO 14693:2003 Petroleum and natural gas industries - Drilling and well-servicing equipment (ISO 14693:2003)
I.S. EN ISO 15138:2007 Petroleum and natural gas industries - Offshore production installations - Heating, ventilation and air-conditioning (ISO 15138:2007)
I.S. EN ISO 15156-1:2009 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 1: General principles for selection of cracking-resistant materials (ISO 15156-1:2009)
I.S. EN ISO 15156-2:2009 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons (ISO 15156-2:2009)
I.S. EN ISO 15156-3:2009 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 3: Cracking-resistant CRAs
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 12 of 42
(corrosion-resistant alloys) and other alloys (ISO 15156-3:2009)
I.S. EN ISO 15544:2010 Petroleum and natural gas industries - Offshore production installations - Requirements and guidelines for emergency response (ISO 15544:2000, including Amd 1:2009)
I.S. EN ISO 15663-1:2006 Petroleum and natural gas industries - Life cycle costing - Part 1: Methodology (ISO 15663-1:2000)
ISO 15663-2:2001 Petroleum and natural gas industries -- Life-cycle costing -- Part 2: Guidance on application of methodology and calculation methods
ISO 15663-3:2001 Petroleum and natural gas industries -- Life-cycle costing -- Part 3: Implementation guidelines
I.S. EN ISO 17776:2002 Petroleum and natural gas industries - Offshore production installations - Guidelines on tools and techniques for hazard identification and risk assessment (ISO 17776:2000)
I.S. EN ISO 20815:2010 Petroleum, petrochemical and natural gas industries - Production assurance and reliability management (ISO 20815:2008, Corrected version 2009-06-15)
I.S. EN ISO 21457:2010 Petroleum, petrochemical and natural gas industries -- Materials selection and corrosion control for oil and gas production systems
S.R. CEN ISO/TS 27469:2011 Petroleum, petrochemical and natural gas industries - Method of test for fire dampers (ISO/TS 27469:2010)
I.S. EN ISO 27509:2012 Petroleum and natural gas industries - Compact flanged connections with IX seal ring (ISO 27509:2012)
S.R. CEN ISO/TS 29001:2011 Petroleum, petrochemical and natural gas industries - Sector-specific quality management systems - Requirements for product and service supply organizations (ISO/TS 29001:2010)
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 13 of 42
4 Offshore structures (Semi submersibles and jack-ups)
Standards listed are from:
ISO/TC 67/SC 4 – Drilling and production equipment
ISO/TC 67/SC 7 – Offshore structures
Standard Number Standard Title
I.S. EN ISO 13624-1:2009 Petroleum and natural gas industries - Drilling and production equipment - Part 1: Design and operation of marine drilling riser equipment (ISO 13624-1:2009)
ISO/TR 13624-2:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Part 2: Deepwater drilling riser methodologies, operations, and integrity technical report
I.S. EN ISO 13625:2002 Petroleum and natural gas industries - Drilling and production equipment - Marine drilling riser couplings (ISO 13625:2002)
I.S. EN ISO 19901-7:2005 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 7: Stationkeeping systems for floating offshore structures and mobile offshore units (ISO 19901-7:2005)
I.S. EN ISO 19904-1:2006 Petroleum and natural gas industries - Floating offshore structures - Part 1: Monohulls, semi-submersibles and spars (ISO 19904-1:2006)
I.S. EN ISO 19905-1:2012 Petroleum and natural gas industries - Site-specific assessment of mobile offshore units - Part 1: Jack-ups (ISO 19905-1:2012)
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 14 of 42
5 Offshore structures (Platforms and jackets)
Standards listed are from:
ISO/TC 67/SC 4 – Drilling and production equipment
ISO/TC 67/SC 7 – Offshore structures
Standard Number Standard Title
I.S. EN ISO 19900:2002 Petroleum and natural gas industries - General requirements for offshore structures (ISO 19900:2002)
I.S. EN ISO 19901-1:2005 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 1: Metocean design and operating considerations (ISO 19901-1:2005)
I.S. EN ISO 19901-2:2004 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 2: Seismic design procedures and criteria (ISO 19901-2:2004)
I.S. EN ISO 19901-3:2010 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 3: Topsides structure (ISO 19901-3:2010)
I.S. EN ISO 19901-4:2003 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 4: Geotechnical and foundation design considerations (ISO 19901-4:2003)
I.S. EN ISO 19901-5:2003 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 5: Weight control during engineering and construction (ISO 19901-5:2003)
I.S. EN ISO 19901-6:2009 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 6: Marine operations (ISO 19901-6:2009)
I.S. EN ISO 19901-7:2005 Petroleum and natural gas industries - Specific requirements for offshore structures - Part 7: Stationkeeping systems for floating offshore structures and mobile offshore units (ISO 19901-7:2005)
I.S. EN ISO 19902:2007 Petroleum and natural gas industries - Fixed steel offshore structures (ISO 19902:2007)
I.S. EN ISO 19903:2006 Petroleum and natural gas industries - Fixed concrete offshore structures (ISO 19903:2006)
I.S. EN ISO 19906:2010 Petroleum and natural gas industries - Arctic offshore structures (ISO 19906:2010)
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 15 of 42
6 Pipeline transportation systems
Standards listed are from:
CEN ECISS/TC 110 - Steel tubes, and iron and steel fittings
CEN/TC 12 - Materials, equipment and offshore structures for petroleum, petrochemical and natural
gas industries
ISO/TC 67/SC 2 - Pipeline transportation systems
Standard Number Standard Title
I.S. ISO 3183:2012 Petroleum and natural gas industries - Steel pipe for pipeline transportation systems
ISO 12490:2011 Petroleum and natural gas industries -- Mechanical integrity and sizing of actuators and mounting kits for pipeline valves
ISO/TS 12747:2011 Petroleum and natural gas industries -- Pipeline transportation systems -- Recommended practice for pipeline life extension
I.S. EN 14161:2011 Petroleum and natural gas industries - Pipeline transportation systems (ISO 13623:2009 modified)
I.S. EN 14163:2001 Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines (ISO 13847:2000 modified)
I.S. EN 13942:2009 Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves (ISO 14313:2007 modified)
I.S. EN ISO 14723:2009 Petroleum and natural gas industries - Pipeline transportation systems - Subsea pipeline valves (ISO 14723:2009)
ISO 15589-1:2003 Petroleum and natural gas industries -- Cathodic protection of pipeline transportation systems -- Part 1: On-land pipelines
ISO 15589-2:2012 Petroleum, petrochemical and natural gas industries -- Cathodic protection of pipeline transportation systems -- Part 2: Offshore pipelines
I.S. EN 14870-1:2011 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 1: Induction bends (ISO 15590-1:2009 modified)
I.S. EN 14870-2:2004 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 2: Fittings (ISO 15590-2:2003 modified)
I.S. EN 14870-3:2006 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges (ISO 15590-3:2004, modified)
I.S. EN ISO 16708:2006 Petroleum and natural gas industries - Pipeline transportation systems - Reliability-based limit state methods (ISO 16708:2006)
I.S. EN ISO 21329:2004 Petroleum and natural gas industries - Pipeline transportation systems - Test procedures for mechanical connectors (ISO 21329:2004)
I.S. EN ISO 21809-2:2007 Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 2: Fusion-bonded epoxy coatings (ISO 21809-2:2007)
ISO 21809-3:2008 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 3: Field joint coatings
ISO 21809-4:2009 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 4: Polyethylene coatings (2-layer PE)
I.S. EN ISO 21809-5:2010 Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 5: External
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 16 of 42
concrete coatings (ISO 21809-5:2010)
7. Onshore processing
Standards listed are from:
ISO/TC 60/SC 2 – Gears - Gear capacity calculation
ISO/TC 67/SC 4 – Drilling and production equipment
ISO/TC 67/SC 6 – Processing equipment and systems
ISO/TC 115/SC 3 – Pumps - Installation and special application
ISO/TC 118/SC 1 – Compressors and pneumatic tools, machines and equipment- Process
compressors
ISO/TC 153/SC 1 – Valves - Design, manufacture, marking and testing
ISO/TC 192 – Gas turbines
CEN/TC 69 – Industrial valves
Standard Number Standard Title
I.S. EN ISO 3977-5:2003 Gas turbines - Procurement - Part 5: Applications for petroleum and natural gas industries (ISO 3977-5:2001)
ISO 10428:1993 Petroleum and natural gas industries -- Sucker rods (pony rods, polished rods, couplings and sub-couplings) -- Specification
ISO 10431:1993 Petroleum and natural gas industries -- Pumping units -- Specification
I.S. EN ISO 10434:2004 Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries (ISO 10434:2004)
I.S. EN ISO 10437:2003 Petroleum, petrochemical and natural gas industries - Steam turbines - Special-purpose applications (ISO 10437:2003)
I.S. EN ISO 10438-1:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 1: General requirements (ISO 10438-1:2007)
I.S. EN ISO 10438-2:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 2: Special-purpose oil systems (ISO 10438-2:2007)
I.S. EN ISO 10438-3:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 3: General-purpose oil systems (ISO 10438-3:2007)
I.S. EN ISO 10438-4:2007 Petroleum, petrochemical and natural gas industries - Lubrication, shaft-sealing and control-oil systems and auxiliaries - Part 4: Self-acting gas seal support systems (ISO 10438-4:2007)
I.S. EN ISO 10439:2002 Petroleum, chemical and gas service industries - Centrifugal compressors (ISO 10439:2002)
I.S. EN ISO 10440-1:2007 Petroleum, petrochemical and natural gas industries - Rotary-type positive-displacement compressors - Part 1: Process compressors (ISO 10440-1:2007)
I.S. EN ISO 10440-2:2001 Petroleum and natural gas industries - Rotary-type positive-displacement
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 17 of 42
compressors - Part 2: Packaged air compressors (oil-free) (ISO 10440-2:2001)
I.S. EN ISO 10441:2007 Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-purpose applications (ISO 10441:2007)
I.S. EN ISO 10442:2002 Petroleum, chemical and gas service industries - Packaged, integrally geared centrifugal air compressors (ISO 10442:2002)
I.S. EN ISO 13631:2002 Petroleum and natural gas industries - Packaged reciprocating gas compressors (ISO 13631:2002)
I.S. EN ISO 13691:2002 Petroleum and natural gas industries - High-speed special-purpose gear units (ISO 13691:2001)
I.S. EN ISO 13704:2007 Petroleum, petrochemical and natural gas industries - Calculation of heater-tube thickness in petroleum refineries (ISO 13704:2007)
I.S. EN ISO 13705:2012 Petroleum, petrochemical and natural gas industries - Fired heaters for general refinery service (ISO 13705:2012)
I.S. EN ISO 13706:2011 Petroleum, petrochemical and natural gas industries - Air-cooled heat exchangers (ISO 13706:2011)
I.S. EN ISO 13709:2009 Centrifugal pumps for petroleum, petrochemical and natural gas industries (ISO 13709:2009)
I.S. EN ISO 13710:2004 Petroleum, petrochemical and natural gas industries - Reciprocating positive displacement pumps (ISO 13710:2004)
I.S. EN ISO 14691:2008 Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - General-purpose applications (ISO 14691:2008)
I.S. EN ISO 15547-1:2005 Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 1: Plate-and-frame heat exchangers (ISO 15547-1:2005)
I.S. EN ISO 15547-2:2005 Petroleum, petrochemical and natural gas industries - Plate-type heat exchangers - Part 2: Brazed aluminium plate-fin heat exchangers (ISO 15547-2:2005)
S.R. CEN/TR 14549:2004 Guide to the use of ISO 15649 and ANSI/ASME B31.3 for piping in Europe in compliance with the Pressure Equipment Directive
I.S. EN ISO 15761:2002 Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries (ISO 15761:2002)
I.S. EN ISO 16812:2007 Petroleum, petrochemical and natural gas industries - Shell-and-tube heat exchangers (ISO 16812:2007)
I.S. EN ISO 17292:2004 Metal ball valves for petroleum, petrochemical and allied industries (ISO 17292:2004)
I.S. EN ISO 21049:2004 Pumps - Shaft sealing systems for centrifugal and rotary pumps (ISO 21049:2004)
I.S. EN ISO 23251:2007 Petroleum, petrochemical and natural gas industries - Pressure-relieving and depressuring systems (ISO 23251:2006)
I.S. EN ISO 23936-1:2009 Petroleum, petrochemical and natural gas industries - Non-metallic materials in contact with media related to oil and gas production - Part 1: Thermoplastics (ISO 23936-1:2009)
S.R. CEN ISO/TS 24817:2011 Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design, installation, testing and inspection (ISO/TS 24817:2006)
I.S. EN ISO 25457:2008 Petroleum, petrochemical and natural gas industries - Flare details for general refinery and petrochemical service (ISO 25457:2008)
I.S. EN ISO 28300:2008 Petroleum, petrochemical and natural gas industries - Venting of
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 18 of 42
atmospheric and low-pressure storage tanks (ISO 28300:2008)
ISO\TC 60 Gears
Secretariat: ANSI
Secretary: Mr. Charlie Fischer
Chairperson: Mr. William A. Bradley (USA) until end 2014
ISO Central Secretariat contact: M. Franck Perrad
Creation date: 1947
Scope ISO/TC 60:
Standardization in the field of gears, including terminology, nominal dimensions, tolerances,
and tools for manufacturing and control.
Total number of published ISO standards related to the TC and its SCs (number includes
updates):
68
Number of published ISO standards under the direct responsibility of TC 60 (number
includes updates):
28
(P) Participating countries: 15
(O) Observing countries: 23
Irelands membership status -
Subcommittees of ISO/TC 60:
TC 60/SC 1 Nomenclature and wormgearing
TC 60/SC 2 Gear capacity calculation
Working Groups of ISO/TC 60:
TC 60/JWG 1 Joint ISO/TC 60-IEC/TC 88 WG: Wind turbine gearboxes
TC 60/WG 2 Accuracy of gears
ISO /TC 60/SC 2: ISO Standards published and referenced in this document
ISO 13691:2001 Petroleum and natural gas industries -- Content and drafting of a functional specification
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 19 of 42
ISO/TC 67
Title: Materials, equipment and offshore structures for petroleum, petrochemical and natural gas
industries
Secretariat: NEN
Secretary: Mr. Harold Pauwels
Chairperson: Mr. Andries Otter
ISO Central Secretariat contact: Mrs. Kirsi Silander
Creation date: 1947
Scope of ISO/TC 67:
Standardization of the materials, equipment and offshore structures used in the drilling, production,
transport by pipelines and processing of liquid and gaseous hydrocarbons within the petroleum,
petrochemical and natural gas industries.
Excluded from the scope are aspects of offshore structures subject to IMO requirements (ISO / TC 8).
Total number of published ISO standards related to the TC and its SCs (number
includes updates):
181
Number of published ISO standards under the direct responsibility of TC 67 (number
includes updates):
18
(P) Participating countries: 32
(O) Observing countries: 30
Irelands membership status O
Subcommittees of ISO/TC 67:
Irelands membership status
TC 67/SC 2 Pipeline transportation systems P
TC 67/SC 3 Drilling and completion fluids, and well cements -
TC 67/SC 4 Drilling and production equipment -
TC 67/SC 5 Casing, tubing and drill pipe -
TC 67/SC 6 Processing equipment and systems -
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 20 of 42
TC 67/SC 7 Offshore structures -
TC 67/SC 8 Arctic operations -
Working Groups of ISO/TC 67:
TC 67/EC/MC Executive committee and Management committee
TC 67/WG 2 Conformity assessment
TC 67/WG 4 Reliability Engineering and technology
TC 67/WG 5 Aluminium alloy pipes
TC 67/WG 7 Corrosion resistant materials
TC 67/WG 8 Materials, corrosion control, welding and jointing, and non-destructive
examination (NDE)
TC 67/WG 10 Liquefied Natural Gas (LNG) installations and equipment
TC 67/WG 11 Coating and lining of structures and equipment
TC 67/WG 12 CO2 aspects
ISO /TC 67: ISO Standards published
ISO 13879:1999 Petroleum and natural gas industries -- Content and drafting of a functional specification
ISO 13880:1999 Petroleum and natural gas industries -- Content and drafting of a technical specification
ISO/TR 13881:2000 Petroleum and natural gas industries -- Classification and conformity assessment of products, processes and services
ISO 14224:2006 Petroleum, petrochemical and natural gas industries -- Collection and exchange of reliability and maintenance data for equipment
ISO 15156-1:2009 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 1: General principles for selection of cracking-resistant materials
ISO 15156-2:2009 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons
ISO 15156-3:2009 Petroleum and natural gas industries -- Materials for use in H2S-containing environments in oil and gas production -- Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys
ISO 15546:2011
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 21 of 42
Petroleum and natural gas industries -- Aluminium alloy drill pipe
ISO 15663-1:2000 Petroleum and natural gas industries -- Life cycle costing -- Part 1: Methodology
ISO 15663-2:2001 Petroleum and natural gas industries -- Life-cycle costing -- Part 2: Guidance on application of methodology and calculation methods
ISO 15663-3:2001 Petroleum and natural gas industries -- Life-cycle costing -- Part 3: Implementation guidelines
ISO 20312:2011 Petroleum and natural gas industries -- Design and operating limits of drill strings with aluminium alloy components
ISO 20815:2008 Petroleum, petrochemical and natural gas industries -- Production assurance and reliability management
ISO 21457:2010 Petroleum, petrochemical and natural gas industries -- Materials selection and corrosion control for oil and gas production systems
ISO 23936-1:2009 Petroleum, petrochemical and natural gas industries -- Non-metallic materials in contact with media related to oil and gas production -- Part 1: Thermoplastics
ISO 23936-2:2011 Petroleum, petrochemical and natural gas industries -- Non-metallic materials in contact with media related to oil and gas production -- Part 2: Elastomers
ISO 28460:2010 Petroleum and natural gas industries -- Installation and equipment for liquefied natural gas -- Ship-to-shore interface and port operations
ISO/TS 29001:2010 Petroleum, petrochemical and natural gas industries -- Sector-specific quality management systems -- Requirements for product and service supply organizations
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 22 of 42
ISO/TC 67/SC 2 - Pipeline transportation systems
Secretariat: UNI
Twinned secretariat: SAC
Secretary: Mr Giuliano Corbella
Twinned secretary: Mr. Changyi Qin
Chairperson: Mr. Denis Tikhomirov until end 2013
ISO Central Secretariat contact: Mrs. Kirsi Silander
Number of published ISO standards under the direct responsibility of TC 67/SC 2 (number
includes updates):
23
(P) Participating countries: 26
(O) Observing countries: 11
Irelands membership status P
ISO 3183:2012 Petroleum and natural gas industries -- Steel pipe for pipeline transportation systems
ISO 12490:2011 Petroleum and natural gas industries -- Mechanical integrity and sizing of actuators and mounting kits for pipeline valves
ISO/TS 12747:2011 Petroleum and natural gas industries -- Pipeline transportation systems -- Recommended practice for pipeline life extension
ISO 13623:2009 Petroleum and natural gas industries -- Pipeline transportation systems
ISO 13847:2000 Petroleum and natural gas industries -- Pipeline transportation systems -- Welding of pipelines
ISO 13847:2000/Cor 1:2001
ISO 14313:2007 Petroleum and natural gas industries -- Pipeline transportation systems -- Pipeline valves
ISO 14313:2007/Cor 1:2009
ISO 14723:2009 Petroleum and natural gas industries -- Pipeline transportation systems -- Subsea pipeline valves
ISO 15589-1:2003 Petroleum and natural gas industries -- Cathodic protection of pipeline transportation systems -- Part 1: On-land pipelines
ISO 15589-2:2012 Petroleum, petrochemical and natural gas industries -- Cathodic protection of pipeline transportation systems --
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 23 of 42
Part 2: Offshore pipelines
ISO 15590-1:2009 Petroleum and natural gas industries -- Induction bends, fittings and flanges for pipeline transportation systems -- Part 1: Induction bends
ISO 15590-2:2003 Petroleum and natural gas industries -- Induction bends, fittings and flanges for pipeline transportation systems -- Part 2: Fittings
ISO 15590-3:2004 Petroleum and natural gas industries -- Induction bends, fittings and flanges for pipeline transportation systems -- Part 3: Flanges
ISO 16708:2006 Petroleum and natural gas industries -- Pipeline transportation systems -- Reliability-based limit state methods
ISO 21329:2004 Petroleum and natural gas industries -- Pipeline transportation systems -- Test procedures for mechanical connectors
ISO 21809-1:2011 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 1: Polyolefin coatings (3-layer PE and 3-layer PP)
ISO 21809-2:2007 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 2: Fusion-bonded epoxy coatings
ISO 21809-2:2007/Cor 1:2008
ISO 21809-3:2008 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 3: Field joint coatings
ISO 21809-3:2008/Amd 1:2011
ISO 21809-4:2009 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 4: Polyethylene coatings (2-layer PE)
ISO 21809-5:2010 Petroleum and natural gas industries -- External coatings for buried or submerged pipelines used in pipeline transportation systems -- Part 5: External concrete coatings
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 24 of 42
ISO/TC 67/SC 3 - Drilling and completion fluids, and well cements
Secretariat: SN
Secretary: Mr Øivind Bråthen
Chairperson: Mr. Roger Tønnessen (Norway) until end 2011
ISO Central Secretariat contact: Mrs. Kirsi Silander
Number of published ISO standards under the direct responsibility of TC 67/SC 3 (number
includes updates):
27
(P) Participating countries: 14
(O) Observing countries: 7
Irelands membership status -
ISO 10414-1:2008 Petroleum and natural gas industries -- Field testing of drilling fluids -- Part 1: Water-based fluids
ISO 10414-2:2011 Petroleum and natural gas industries -- Field testing of drilling fluids -- Part 2: Oil-based fluids
ISO 10416:2008 Petroleum and natural gas industries -- Drilling fluids -- Laboratory testing
ISO 10426-1:2009 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 1: Specification
ISO 10426-1:2009/Cor 1:2010
ISO 10426-1:2009/Cor 2:2012
ISO 10426-2:2003 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 2: Testing of well cements
ISO 10426-2:2003/Cor 1:2006
ISO 10426-2:2003/Amd 1:2005 Water-wetting capability testing
ISO 10426-3:2003 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 3: Testing of deepwater well cement formulations
ISO 10426-4:2004 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 4: Preparation and testing of foamed cement slurries at atmospheric pressure
ISO 10426-5:2004 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 5: Determination of shrinkage and expansion of well cement formulations at atmospheric pressure
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 25 of 42
ISO 10426-6:2008 Petroleum and natural gas industries -- Cements and materials for well cementing -- Part 6: Methods for determining the static gel strength of cement formulations
ISO 10427-1:2001 Petroleum and natural gas industries -- Equipment for well cementing -- Part 1: Casing bow-spring centralizers
ISO 10427-2:2004 Petroleum and natural gas industries -- Equipment for well cementing -- Part 2: Centralizer placement and stop-collar testing
ISO 10427-3:2003 Petroleum and natural gas industries -- Equipment for well cementing -- Part 3: Performance testing of cementing float equipment
ISO 13500:2008 Petroleum and natural gas industries -- Drilling fluid materials -- Specifications and tests
ISO 13500:2008/Cor 1:2009
ISO 13500:2008/Amd 1:2010 Barite 4,1
ISO 13501:2011 Petroleum and natural gas industries -- Drilling fluids -- Processing equipment evaluation
ISO 13503-1:2011 Petroleum and natural gas industries -- Completion fluids and materials -- Part 1: Measurement of viscous properties of completion fluids
ISO 13503-2:2006 Petroleum and natural gas industries -- Completion fluids and materials -- Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations
ISO 13503-2:2006/Amd 1:2009 Addition of Annex B: Proppand specification
ISO 13503-3:2005 Petroleum and natural gas industries -- Completion fluids and materials -- Part 3: Testing of heavy brines
ISO 13503-3:2005/Cor 1:2006
ISO 13503-4:2006 Petroleum and natural gas industries -- Completion fluids and materials -- Part 4: Procedure for measuring stimulation and gravel-pack fluid leak off under static conditions
ISO 13503-5:2006 Petroleum and natural gas industries -- Completion fluids and materials -- Part 5: Procedures for measuring the long-term conductivity of proppants
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 26 of 42
ISO/TC 67/SC 4 - Drilling and production equipment
Secretariat: ANSI
Secretary: Dr. Edmund Baniak
Chairperson: Dr. Austin Freeman (USA) until end 2013
ISO Central Secretariat contact: Mrs. Kirsi Silander
Number of published ISO standards under the direct responsibility of TC 67/SC 4 (number
includes updates):
48
(P) Participating countries: 17
(O) Observing countries: 8
Irelands membership status -
ISO 10407:1993 Petroleum and natural gas industries -- Drilling and production equipment -- Drill stem design and operating limits
ISO 10407-2:2008 Petroleum and natural gas industries -- Rotary drilling equipment -- Part 2: Inspection and classification of used drill stem elements
ISO 10407-2:2008/Cor 1:2009
ISO 10417:2004 Petroleum and natural gas industries -- Subsurface safety valve systems -- Design, installation, operation and redress
ISO 10423:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Wellhead and christmas tree equipment
ISO 10424-1:2004 Petroleum and natural gas industries -- Rotary drilling equipment -- Part 1: Rotary drill stem elements
ISO 10424-2:2007 Petroleum and natural gas industries -- Rotary drilling equipment -- Part 2: Threading and gauging of rotary shouldered thread connections
ISO 10428:1993 Petroleum and natural gas industries -- Sucker rods (pony rods, polished rods, couplings and sub-couplings) -- Specification
ISO 10431:1993 Petroleum and natural gas industries -- Pumping units -- Specification
ISO 10432:2004 Petroleum and natural gas industries -- Downhole equipment -- Subsurface safety valve equipment
ISO 13533:2001 Petroleum and natural gas industries -- Drilling and production equipment -- Drill-through equipment
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 27 of 42
ISO 13533:2001/Cor 1:2005
ISO 13534:2000 Petroleum and natural gas industries -- Drilling and production equipment -- Inspection, maintenance, repair and remanufacture of hoisting equipment
ISO 13535:2000 Petroleum and natural gas industries -- Drilling and production equipment -- Hoisting equipment
ISO 13624-1:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Part 1: Design and operation of marine drilling riser equipment
ISO/TR 13624-2:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Part 2: Deepwater drilling riser methodologies, operations, and integrity technical report
ISO 13625:2002 Petroleum and natural gas industries -- Drilling and production equipment -- Marine drilling riser couplings
ISO 13626:2003 Petroleum and natural gas industries -- Drilling and production equipment -- Drilling and well-servicing structures
ISO 13628-1:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 1: General requirements and recommendations
ISO 13628-1:2005/Amd 1:2010 Revised Clause 6
ISO 13628-2:2006 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 2: Unbonded flexible pipe systems for subsea and marine applications
ISO 13628-2:2006/Cor 1:2009
ISO 13628-3:2000 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 3: Through flowline (TFL) systems
ISO 13628-4:2010 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 4: Subsea wellhead and tree equipment
ISO 13628-4:2010/Cor 1:2011
ISO 13628-5:2009 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 5: Subsea umbilicals
ISO 13628-6:2006 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 6: Subsea production control systems
ISO 13628-7:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 7: Completion/workover riser systems
ISO 13628-8:2002 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 8: Remotely
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 28 of 42
Operated Vehicle (ROV) interfaces on subsea production systems
ISO 13628-8:2002/Cor 1:2005
ISO 13628-9:2000 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 9: Remotely Operated Tool (ROT) intervention systems
ISO 13628-10:2005 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 10: Specification for bonded flexible pipe
ISO 13628-11:2007 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 11: Flexible pipe systems for subsea and marine applications
ISO 13628-11:2007/Cor 1:2008
ISO 13628-15:2011 Petroleum and natural gas industries -- Design and operation of subsea production systems -- Part 15: Subsea structures and manifolds
ISO 14310:2008 Petroleum and natural gas industries -- Downhole equipment -- Packers and bridge plugs
ISO 14693:2003 Petroleum and natural gas industries -- Drilling and well-servicing equipment
ISO 15136-1:2009 Petroleum and natural gas industries -- Progressing cavity pump systems for artificial lift -- Part 1: Pumps
ISO 15136-2:2006 Petroleum and natural gas industries -- Progressing cavity pump systems for artificial lift -- Part 2: Surface-drive systems
ISO 16070:2005 Petroleum and natural gas industries -- Downhole equipment -- Lock mandrels and landing nipples
ISO 17078-1:2004 Petroleum and natural gas industries -- Drilling and production equipment -- Part 1: Side-pocket mandrels
ISO 17078-1:2004/Amd 1:2010
ISO 17078-2:2007 Petroleum and natural gas industries -- Drilling and production equipment -- Part 2: Flow-control devices for side-pocket mandrels
ISO 17078-2:2007/Cor 1:2009
ISO 17078-3:2009 Petroleum and natural gas industries -- Drilling and production equipment -- Part 3: Running tools, pulling tools and kick-over tools and latches for side-pocket mandrels
ISO 17078-4:2010 Petroleum and natural gas industries -- Drilling and production equipment -- Part 4: Practices for side-pocket mandrels and related equipment
ISO 17824:2009 Petroleum and natural gas industries -- Downhole equipment -- Sand screens
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 29 of 42
ISO 28781:2010 Petroleum and natural gas industries -- Drilling and production equipment --Subsurface barrier valves and related equipment
ISO/TC 67/SC 5 - Casing, tubing and drill pipe
Secretariat: JISC
Secretary: Mr. Tsunehiro Ise
Chairperson: Mr. Yoshi Kusaka (Japan) until end 2011
ISO Central Secretariat contact: Mrs. Kirsi Silander
Number of published ISO standards under the direct responsibility of TC 67/SC 5 (number
includes updates):
10
(P) Participating countries: 20
(O) Observing countries: 10
Irelands membership status -
ISO/TR 10400:2007 Petroleum and natural gas industries -- Equations and calculations for the properties of casing, tubing, drill pipe and line pipe used as casing or tubing
ISO 10405:2000 Petroleum and natural gas industries -- Care and use of casing and tubing
ISO 11960:2011 Petroleum and natural gas industries -- Steel pipes for use as casing or tubing for wells
ISO 11961:2008 Petroleum and natural gas industries -- Steel drill pipe
ISO 11961:2008/Cor 1:2009
ISO 13678:2010 Petroleum and natural gas industries -- Evaluation and testing of thread compounds for use with casing, tubing, line pipe and drill stem elements
ISO 13679:2002 Petroleum and natural gas industries -- Procedures for testing casing and tubing connections
ISO 13680:2010 Petroleum and natural gas industries -- Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock -- Technical delivery conditions
ISO 15463:2003 Petroleum and natural gas industries -- Field inspection of new casing, tubing and plain-end drill pipe
ISO 15463:2003/Cor 1:2009
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 30 of 42
ISO/TC 67/SC 6 - Processing equipment and systems
Secretariat: AFNOR
Secretary: Mme Alice Jubeau
Chairperson: M. Joël Fort (France) until end 2014
ISO Central Secretariat contact: Mrs. Kirsi Silander
Number of published ISO standards under the direct responsibility of TC 67/SC 6 (number
includes updates):
41
(P) Participating countries: 21
(O) Observing countries: 7
Irelands membership status -
ISO 10418:2003 Petroleum and natural gas industries -- Offshore production installations -- Analysis, design, installation and testing of basic surface process safety systems
ISO 10418:2003/Cor 1:2008
ISO 10437:2003 Petroleum, petrochemical and natural gas industries -- Steam turbines -- Special-purpose applications
ISO 10438-1:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 1: General requirements
ISO 10438-2:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 2: Special-purpose oil systems
ISO 10438-3:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 3: General-purpose oil systems
ISO 10438-4:2007 Petroleum, petrochemical and natural gas industries -- Lubrication, shaft-sealing and control-oil systems and auxiliaries -- Part 4: Self-acting gas seal support systems
ISO 10441:2007 Petroleum, petrochemical and natural gas industries -- Flexible couplings for mechanical power transmission -- Special-purpose applications
ISO 12211:2012 Petroleum, petrochemical and natural gas industries -- Spiral plate heat exchangers
ISO 12212:2012 Petroleum, petrochemical and natural gas industries -- Hairpin-type heat exchangers
ISO 13702:1999 Petroleum and natural gas industries -- Control and mitigation of fires and explosions on offshore production
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 31 of 42
installations -- Requirements and guidelines
ISO 13703:2000 Petroleum and natural gas industries -- Design and installation of piping systems on offshore production platforms
ISO 13703:2000/Cor 1:2002
ISO 13704:2007 Petroleum, petrochemical and natural gas industries -- Calculation of heater-tube thickness in petroleum refineries
ISO 13704:2007/Cor 1:2008
ISO 13705:2012 Petroleum, petrochemical and natural gas industries - Fired heaters for general refinery service
ISO 13706:2011 Petroleum, petrochemical and natural gas industries -- Air-cooled heat exchangers
ISO 14691:2008 Petroleum, petrochemical and natural gas industries -- Flexible couplings for mechanical power transmission -- General-purpose applications
ISO 14692-1:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 1: Vocabulary, symbols, applications and materials
ISO 14692-2:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 2: Qualification and manufacture
ISO 14692-2:2002/Cor 1:2005
ISO 14692-3:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 3: System design
ISO 14692-3:2002/Cor 1:2005
ISO 14692-4:2002 Petroleum and natural gas industries -- Glass-reinforced plastics (GRP) piping -- Part 4: Fabrication, installation and operation
ISO 14692-4:2002/Cor 1:2006
ISO 15138:2007 Petroleum and natural gas industries -- Offshore production installations -- Heating, ventilation and air-conditioning
ISO 15544:2000 Petroleum and natural gas industries -- Offshore production installations -- Requirements and guidelines for emergency response
ISO 15544:2000/Amd 1:2009
ISO 15547-1:2005 Petroleum, petrochemical and natural gas industries -- Plate-type heat exchangers -- Part 1: Plate-and-frame heat exchangers
ISO 15547-2:2005
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 32 of 42
Petroleum, petrochemical and natural gas industries -- Plate-type heat exchangers -- Part 2: Brazed aluminium plate-fin heat exchangers
ISO 15649:2001 Petroleum and natural gas industries -- Piping
ISO 16812:2007 Petroleum, petrochemical and natural gas industries -- Shell-and-tube heat exchangers
ISO 17776:2000 Petroleum and natural gas industries -- Offshore production installations -- Guidelines on tools and techniques for hazard identification and risk assessment
ISO 23251:2006 Petroleum, petrochemical and natural gas industries -- Pressure-relieving and depressuring systems
ISO 23251:2006/Cor 1:2007
ISO 23251:2006/Amd 1:2008
ISO/TS 24817:2006 Petroleum, petrochemical and natural gas industries -- Composite repairs for pipework -- Qualification and design, installation, testing and inspection
ISO 25457:2008 Petroleum, petrochemical and natural gas industries -- Flare details for general refinery and petrochemical service
ISO/TS 27469:2010 Petroleum, petrochemical and natural gas industries - Method of test for fire dampers
ISO 28300:2008 Petroleum, petrochemical and natural gas industries -- Venting of atmospheric and low-pressure storage tanks
ISO 28300:2008/Cor 1:2009
ISO/TC 67/SC 7 - Offshore structures
Secretariat: BSI
Secretary: Dr. Charles A. Whitlock
Chairperson: Mr. Philip Smedley (United Kingdom) until end 2013
ISO Central Secretariat contact: Mrs. Kirsi Silander
Number of published ISO standards under the direct responsibility of TC 67/SC 7 (number
includes updates):
14
(P) Participating countries: 22
(O) Observing countries: 9
Irelands membership status -
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 33 of 42
ISO 19900:2002 Petroleum and natural gas industries -- General requirements for offshore structures
ISO 19901-1:2005 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 1: Metocean design and operating considerations
ISO 19901-2:2004 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 2: Seismic design procedures and criteria
ISO 19901-3:2010 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 3: Topsides structure
ISO 19901-4:2003 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 4: Geotechnical and foundation design considerations
ISO 19901-5:2003 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 5: Weight control during engineering and construction
ISO 19901-6:2009 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 6: Marine operations
ISO 19901-6:2009/Cor 1:2011
ISO 19901-7:2005 Petroleum and natural gas industries -- Specific requirements for offshore structures -- Part 7: Stationkeeping systems for floating offshore structures and mobile offshore units
ISO 19902:2007 Petroleum and natural gas industries -- Fixed steel offshore structures
ISO 19903:2006 Petroleum and natural gas industries -- Fixed concrete offshore structures
ISO 19904-1:2006 Petroleum and natural gas industries -- Floating offshore structures -- Part 1: Monohulls, semi-submersibles and spars
ISO 19905-1:2012 Petroleum and natural gas industries -- Site-specific assessment of mobile offshore units -- Part 1: Jack-ups
ISO 19906:2010 Petroleum and natural gas industries -- Arctic offshore structures
ISO/TC 67/SC 8 Arctic operations
Secretariat: GOST R
Secretary: Mrs. Liudmila Zalevskaya
Chairperson: Mr. Mikhail Rusakov until end 2017
ISO Central Secretariat contact: Mrs. Kirsi Silander
Creation date: 2011
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 34 of 42
Number of published ISO standards under the direct responsibility of TC 67/SC 7 (number
includes updates):
0
(P) Participating countries: 9
(O) Observing countries: 0
Irelands membership status -
ISO/TC 115 - Pumps
Secretariat: AFNOR
Secretary: M. Jacques Amaraggi
Chairperson: M. René-André Barbarulo (France) until end 2012
ISO Central Secretariat contact: Mrs. Kirsi Silander
Creation date: 1964
Scope of ISO/TC 115:
Standardization in the field of pumps; including:
dimensions and technical specifications,
test methods and conditions of acceptance for rotodynamic and positive displacement pumps
for all liquids, including complete pumping installations,
installations and special applications, as well as rotodynamic mixers for waste water
Total number of published ISO standards related to the TC and its SCs (number includes
updates):
24
Number of published ISO standards under the direct responsibility of TC 115 (number
includes updates):
4
(P) Participating countries: 21
(O) Observing countries: 15
Irelands membership status -
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 35 of 42
Subcommittees of ISO/TC 115:
Irelands membership status
TC 115/SC 1 Dimensions and technical specifications of pumps -
TC 115/SC 2 Methods of measurement and testing -
TC 115/SC 3 Installation and special application -
Working Groups of ISO/TC 115:
TC 115/WG 7 Pumping system energy assessment
ISO/TC 115/SC 3: ISO Standards published and referenced in this document
ISO 13709:2009 Centrifugal pumps for petroleum, petrochemical and natural gas industries
ISO 13710:2004 Petroleum, petrochemical and natural gas industries -- Reciprocating positive displacement pumps
ISO 21049:2004 Pumps -- Shaft sealing systems for centrifugal and rotary pumps
ISO/TC 118 - Compressors and pneumatic tools, machines and equipment
Secretariat: SIS
Secretary: Ms Lena Fagervall
Chairperson: Mrs. Jenny Buck (United Kingdom) until end 2013
ISO Central Secretariat contact: Mrs. Kirsi Silander
Creation date: 1965
Scope of ISO/TC 118:
Standardization in the field of:
air compressors;
compressors for the process, petroleum, chemical and gas industry services;
pneumatic tools and machines;
compressed air purity specification and compressed air treatment equipment.
Excluded from the scope are pneumatic tool shanks and tool fitting dimensions, as they fall within
the scope of ISO / TC 29.
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 36 of 42
Total number of published ISO standards related to the TC and its SCs (number includes
updates):
68
(P) Participating countries: 13
(O) Observing countries: 23
Irelands membership status -
Subcommittees of ISO/TC 118:
Irelands membership status
TC 118/SC 1 Process compressors `-
TC 118/SC 3 Pneumatic tools and machines -
TC 118/SC 4 Compressed air purity specification and compressed air treatment
equipment
-
TC 118/SC 6 Air compressors and compressed air systems -
There are no Working Groups within ISO/TC 118.
ISO/TC 118/SC 1: ISO Standards published and referenced in this document
ISO 10439:2002 Petroleum, chemical and gas service industries -- Centrifugal compressors
ISO 10440-1:2007 Petroleum, petrochemical and natural gas industries -- Rotary-type positive-displacement compressors -- Part 1: Process compressors
ISO 10440-2:2001 Petroleum and natural gas industries -- Rotary-type positive-displacement compressors -- Part 2: Packaged air compressors (oil-free)
ISO 10442:2002 Petroleum, chemical and gas service industries -- Packaged, integrally geared centrifugal air compressors
ISO 13631:2002 Petroleum and natural gas industries -- Packaged reciprocating gas compressors
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 37 of 42
ISO/TC 153 - Valves
Secretariat: vacant
Secretary:
Chairperson: vacant
ISO Central Secretariat contact: M. Franck Perrad
Creation date: 1971
Scope of ISO/TC 153:
Standardization in the field of industrial valves and steam traps. The standardization to include
parameters covering interchangeability, valve mating details for actuator mounting, testing,
marking, quality requirements, terminology and other relevant parameters.
Excluded from the scope are:
safety and relief valves and other pressure relief devices which are the responsibility of
ISO/TC 185;
production valves for wellhead equipment and valves for cross country pipelines for the
petroleum and natural gas industries which are the responsibility of ISO/TC 67;
valves forming the final control element used for industrial process control systems which are
the responsibility of IEC/TC 65;
valves having an envelope predominantly made of plastics which are the responsibility of
ISO/TC 138;
valves for sanitary use.
Total number of published ISO standards related to the TC and its SCs (number includes
updates):
25
Number of published ISO standards under the direct responsibility of TC 153 (number
includes updates):
8
(P) Participating countries: 15
(O) Observing countries: 31
Irelands membership status -
Subcommittees of ISO/TC 153:
Irelands membership status
TC 153/SC 1 Design, manufacture, marking and testing -
TC 153/SC 2 Valve actuator attachment -
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 38 of 42
There are no Working Groups within ISO/TC 153.
ISO/TC 153/SC 1: ISO Standards published and referenced in this document
ISO 10434:2004 Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries
ISO 15761:2002 Steel gate, globe and check valves for sizes DN 100 and smaller, for the petroleum and natural gas industries
ISO 17292:2004 Metal ball valves for petroleum, petrochemical and allied industries
ISO/TC 192 - Gas turbines
Secretariat: ANSI
Secretary: Mr. Robin Proctor
Chairperson: Mr. Benjamin Wiant (USA) until end 2013
ISO Central Secretariat contact: M. Franck Perrad
Creation date: 1988
Scope of ISO/TC 192:
Standardization in the field of all aspects of gas turbine design, application, installation, operation
and maintenance, including simple turbine cycles, combined cycle systems, definitions,
procurement, acceptance, performance, environment (on the gas turbine itself and the external
environment) and methods of test.
ISO/TC 192 is responsible for preparing horizontal standards for all types of gas turbines. Work on
aero gas turbine engines shall be undertaken in liaison with those technique committees having the
primary responsability.
Note: ISO/TC 20 has the primary responsibility of preparing standards relative to the specific
application of gas turbines to aerospace.
Total number of published ISO standards related to the TC and its SCs (number includes
updates):
16
Number of published ISO standards under the direct responsibility of TC 192 (number
includes updates):
16
Participating countries: 14
Observing countries: 12
Irelands membership status -
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 39 of 42
There are no Subcommittees within ISO/TC 192.
Working Groups of ISO/TC 192:
TC 192/WG 3 Combined cycles
TC 192/WG 4 Joint TC 192-TC 67/SC 6 WG : Gas turbine
TC 192/WG 7 Fuels, environment
TC 192/WG 8 Trend monitoring systems
TC 192/WG 9 Electric power applications
TC 192/WG 10 Gas turbine safety
TC 192/WG 11 Acceptance tests
TC 192/WG 12 Microturbines
TC 192/WG 13 Cogeneration systems
ISO/TC 192: ISO Standards published and referenced in this document
ISO 3977-5:2001 Gas turbines -- Procurement -- Part 5: Applications for petroleum and natural gas industries
This ISO Standard has been adopted by CEN/TC 12
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 40 of 42
CEN/TC 12 - Materials, equipment and offshore structures for petroleum, petrochemical and
natural gas industries
Status: Active
Secretariat: AFNOR
Secretary: Ms A. Jubeau ([email protected])
Chairperson: Mr G. Trican (FR)
CCMC PM: Mrs M. Poidevin
There are no Working Groups in this Technical Committee.
This Technical Committee mirrors the work of ISO/TC 67 at a European level and adopts, were
appropriate, ISO Standards as European Standards.
Where modification have been made to ISO Standards they have been published by the Technical
Committee as separate European Standards.
CEN/TC 12 Standards published and referenced in this documentEN
14163:2001
Petroleum and natural gas industries - Pipeline transportation systems - Welding of pipelines (ISO 13847:2000 modified)
EN 14870-2:2004 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 2: Fittings (ISO 15590-2:2003 modified)
EN 14870-3:2006 Petroleum and natural gas industries - Induction bends, fittings and flanges for pipeline transportation systems - Part 3: Flanges (ISO 15590-3:2004, modified)
CEN/TR 14549:2004 Guide to the use of ISO 15649 and ANSI/ASME B31.3 for piping in Europe in compliance with the Pressure Equipment Directive
EN 13942:2009 Petroleum and natural gas industries - Pipeline transportation systems - Pipeline valves (ISO 14313:2007 modified)
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 41 of 42
CEN/TC 69 – Industrial valves
Status: Active
Secretariat: AFNOR
Secretary: Ms H.Cros ([email protected])
Chairperson: Mr P.Vinzio (FR)
CCMC PM: Mr T. Legrand
Scope: The standardization of valves for all industrial applications and for all types of fluids,
including : - steam traps; - valve actuator interface; - safety devices against excessive pressure
(safety valves and bursting disks); - control valves (excluding the actuator element and their
interface); but excluding: - sanitary valves (as defined by CEN/TC 164/WG 8).
CEN/TC 69/WG 1 Basic standards
CEN/TC 69/WG 4 Butterfly valves
CEN/TC 69/WG 5 Plug and ball valves
CEN/TC 69/WG 6 Check valves
CEN/TC 69/WG 8 Valves for liquified natural gas and for the distribution of natural gas
CEN/TC 69/WG 9 Valves for the transport of petroleum and natural gas
CEN/TC 69/WG 10 Safety devices against excessive pressure
CEN/TC 69/WG 12 Valves for the process industry
CEN/TC 69/WG 14 Fire hydrants
CEN/TC 69/WG 16 Plastic valves
CEN/TC 69/WG 17 Metallic and thermoplastic valves for water supply
Petroleum Exploration and Extraction Technical Standards Committee
NSAI Standards
1 Swift Square, Northwood, Santry, Dublin 9
Page 42 of 42
CEN ECISS/TC 110 - Steel tubes, and iron and steel fittings
Status: Active
Secretariat: UNI
Secretary: Mr V.Vergani ([email protected])
Chairperson: Mr R.Zanetti (IT)
CCMC PM: Mr A. Da Costa
Scope: Standardization of technical delivery conditions for steel tubes and iron and steel fittings for
steel tubes for all applications. Included are the metallic and organic coatings, threading (including
gauging) and mechanical and non-destructive testing. Excluded are design, calculation and testing of
metallic piping systems, flanges and hollow sections
Working Groups of ECISS/TC 110:
ECISS/TC 110/WG 1 Tubes for pressure purposes
ECISS/TC 110/WG 2 Line pipe
ECISS/TC 110/WG 3 Fittings
ECISS/TC 110/WG 4 Coatings for steel tubes
ECISS/TC 110/WG 5 Tube for the conveyance of aqueous liquids
ECISS/TC 110/WG 6 Tube threads and service tubes
ECISS/TC 110/WG 7 Dimensions and tolerances
ECISS/TC 110/WG 8 Mechanical testing of tubes
ECISS/TC 110/WG 9 Non-destructive testing
ECISS/TC 110/WG 10 Tubes for mechanical and general engineering purposes
CEN ECISS/TC 110 Standards published and referenced in this document EN ISO 3183:2012
Petroleum and natural gas industries - Steel pipe for pipeline transportation systems (ISO 3183:2012)