NOTES · 2019-02-05 · knauf putty pad system performance: fire : 60:60ei sound: 45db rw max height*:3800mm impact duty**:severe min. ... knauf putty pad. system performance: fire

A

B

C

D

E

F

G

H

I

J

K

L

M

NOTES

PROJECT:

TITLE:

DRN:

DRG. No:

REV. No:

SCALE:

DATE:

1 x15mm KNAUF SOUNDSHIELD PLUS

70mm [0.50] 'C' STUD AT MAX.600mm CENTRES

KNAUF FIXINGS

72mm KNAUF 'U' CHANNEL

25mm KNAUF EARTHWOOLACOUSTIC ROLL

KNAUF INTUMESCENT & ACOUSTICMASTIC

KNAUF PREMIUM JOINTING RANGEAND KNAUF BEADING RANGE

KNAUF FLAT PLATE

SHAPED TIMBER GROUND (BYOTHERS)

ADDITIONAL KNAUF 'C' STUDABUTMENT IF NECESSARY

72mm KNAUF DEEP FLANGE 'U'CHANNEL

KNAUF FIRE PANEL FILLETS TO SUITDEFLECTION WITH 10mm OVERLAP

KNAUF PUTTY PAD

SYSTEM PERFORMANCE:FIRE : 60:60EISOUND: 45dB RwMAX HEIGHT*: 3800mmIMPACT DUTY**: SEVEREMIN. WIDTH: 102mm*MAXIMUM HEIGHT CALCULATED BASED ON A LIMITING DEFLECTION OF L/240 AT

200Pa

**IMPACT DUTY IN ACCORDANCE WITH BS5234-2: 1992 ANNEXES B, C, D, E.

O KNAUF READY MIX FINISH

PFH1-13

STANDARD DETAILS

SHEET 1 OF 6

NTSTECH

2018 A

1. SECTION THROUGH ON PLAN 2. ABUTMENT TO CONCRETE 3. CORNER JUNCTION

4. DEFLECTION HEAD 5. T-JUNCTION 6. SPLAYED ANGLE CORNER

AutoCAD SHX Text

DEFLECTION ALLOWANCE

AutoCAD SHX Text


AutoCAD SHX Text


150mm

A

B

C

D

E

F

G

H

I

J

K

L

M

NOTES

PROJECT:

TITLE:

DRN:

DRG. No:

REV. No:

SCALE:

DATE:



KNAUF FIXINGS





KNAUF FLAT PLATE





KNAUF PUTTY PAD


200Pa



PFH1-13

STANDARD DETAILS

SHEET 2 OF 6

NTSTECH

2018 A

1. PERFORMER TO ISOLATOR JUNCTION 2. INDEPENDENT 'I' STUD LINING TO PERFORMERJUNCTION

3. WALL LINER TO PERFORMER JUNCTION

4. PUTTY PAD DETAIL 6. FAIR END DETAIL5. PUTTY PAD DETAIL

CURTAIN WALLING

LATERALDEFLECTIONALLOWANCE CANNOT

EXCEED250mm

ACOUSTIC FLANKING DETAILDETAIL OMITTED ON OPPOSITESIDE FOR CLARITY

ADHERED OR FIXED TOCURTAIN WALLING

NOTE : DETAIL TO BE APPROVED BY PROJECT DESIGN TEAM

INSULATION TO ISOLATE BOARD FROM MULLIONWITH PLASTER STOP AND INTUMESCENT MASTICBEAD. NO MECHANICAL FIXINGS TO MULLION

NOTE : DETAIL TO BE APPROVED BY PROJECT DESIGN TEAM

CANNOTEXCEED250mm

KNAUF EARTHWOOLBUILDING SLAB RS60


MAXIMUM 1/3 OVERHANG

MIN. 18mm PLY

25mm

150mm

FIXINGS AT150mm CENTRES

150mm

150mm

125mm

25 x 25mm KNAUFANGLE SECTION

KNAUF INSULATIONRS60

A

B

C

D

E

F

G

H

I

J

K

L

M

NOTES

PROJECT:

TITLE:

DRN:

DRG. No:

REV. No:

SCALE:

DATE:



KNAUF FIXINGS





KNAUF FLAT PLATE





KNAUF PUTTY PAD


200Pa



PFH1-13

STANDARD DETAILS

SHEET 3 OF 6

NTSTECH

2018 A

1. CURTAIN WALLING ABUTMENT 2. MULLION ABUTMENT 3. SLAB EDGE DETAIL

4. PATTRESS DETAIL 5. MOVEMENT CONTROL JOINT

WHERE PLYWOOD IS REQUIRED TO RESILIENT BAR SIDE IT MUST BEAPPLIED ON TOP OF RESILIENT BAR IN ORDER TO MAINTAINACOUSTIC PERFORMANCE

AutoCAD SHX Text

FIRE RATING UP TO THIS POINT

AutoCAD SHX Text

LATERAL DEFLECTION ALLOWANCE

A

B

C

D

E

F

G

H

I

J

K

L

M

NOTES

PROJECT:

TITLE:

DRN:

DRG. No:

REV. No:

SCALE:

DATE:



KNAUF FIXINGS





KNAUF FLAT PLATE





KNAUF PUTTY PAD


200Pa



PFH1-13

STANDARD DETAILS

SHEET 4 OF 6

NTSTECH

2018 A

1. DOOR JAMB 0-60kgs 2. DOOR JAMB 60-100kgs

PLEASE NOTE· TIMBER GROUND NOT REQUIRED FOR

STRUCTURAL PERFORMANCE, HOWEVER MAYBE REQUIRED BY DOOR MANUFACTURER.

· DOOR JAMB ARRANGEMENT REPEATED BOTHSIDES OF DOOR OPENING

· POSITION OF FLAT PLATE TO SUIT DEFLECTIONALLOWANCE (IF REQUIRED)

PLEASE NOTE· TIMBER GROUND NOT REQUIRED FOR

STRUCTURAL PERFORMANCE, HOWEVER MAYBE REQUIRED BY DOOR MANUFACTURER.

· DOOR JAMB ARRANGEMENT REPEATED BOTHSIDES OF DOOR OPENING

· POSITION OF FLAT PLATE TO SUIT DEFLECTIONALLOWANCE (IF REQUIRED)

AutoCAD SHX Text

MIN 250mm

AutoCAD SHX Text

MIN 300mm

AutoCAD SHX Text

150mm

AutoCAD SHX Text

MIN 250mm

AutoCAD SHX Text

MIN 300mm

AutoCAD SHX Text

150mm

A

B

C

D

E

F

G

H

I

J

K

L

M

NOTES

PROJECT:

TITLE:

DRN:

DRG. No:

REV. No:

SCALE:

DATE:



KNAUF FIXINGS





KNAUF FLAT PLATE





KNAUF PUTTY PAD


200Pa



PFH1-13

STANDARD DETAILS

SHEET 5 OF 6

NTSTECH

2018 A

1. DETAIL A 2. DETAIL B

3. DETAIL C 4. DETAIL D

DETAIL A - FRAMED & LINED, SINGLE KNAUF FIRE BATT UP TO 60MINUTES INTEGRITY & 60 INSULATION WITHIN KNAUF FIRE RESISTANTSYSTEMS OF UP TO 60 MINUTES INTEGRITY & INSULATION

INSTALLATION INSTRUCTIONS

1. ENSURE WITHIN APERTURE IS CLEAN AND FREE OF DE-BRIS LOOSE CEMENT, AND REMOVE ALL DUST FROM SURFACES REQUIRING INSTALLATION.

GENERAL

1. COAT ALL EXPOSED EDGES OF KNAUF FIRE BATT AND DAMAGES TO COATING WITH KNAUF FIRE MASTIC BRUSH GRADE.

2. APPLY KNAUF FIRE MASTIC BEAD TO ALL KNAUF FIRE BATT INTERFACES/ JOINTS.

DETAIL B - SINGLE KNAUF FIRE BATT WITH KNAUFFIRE BATT LINED OPENING RATED AS DETAIL A FOR UP TO 60 MINUTESINTEGRITY & INSULATION WITHIN KNAUF FIRE RESISTANT SYSTEMS OFUP TO 60 MINUTES INTEGRITY & INSULATION

1. CUT KNAUF FIRE BATT TO FORM LINING TO FRAMED APERTURE, ENSURING KNAUF FIRE BATT FINISHES FLUSH WITH FACE OF PLASTERBOARD.

2. BOND KNAUF FIRE BATT LINING TO FRAMED OPENING WITH KNAUF FIRE MASTIC.3. FIT KNAUF FIRE BATT IN TO OPENING ENSURING GOOD BONDING TO FRAMING AND PLASTERBOARD EDGE.

DETAIL C - UNFRAMED, UNLINED, DOUBLE PATRESSKNAUF FIRE BATT RATED UP TO 120 MINUTESINTEGRITY & INSULATION1. CUT KNAUF FIRE BATT TO REQUIRED SIZE AND SHAPE, ENSURING THE KNAUF FIRE BATT WILL OVERLAP THE KNAUF PLASTERBOARD A MINIMUM OF 75MM AROUND THE OPENING.2. APPLY KNAUF FIRE MASTIC TO KNAUF PLASTERBOARD WHERE THE KNAUF FIRE BATT IS TO BE FITTED, TO BOND KNAUF FIRE BATT TO PLASTERBOARD AND KNAUF FIRE BATT TO KNAUF FIRE BATT.3. FIRMLY PRESS KNAUF FIRE BATT TO KNAUF PLASTERBOARD TO ENSURE BOND.4. FIX THE KNAUF FIRE BATT TO THE KNAUF PLASTERBOARD USING MINIMUM 75MM LONG STEEL SCREWS AND 25MM DIAMETER STEEL WASHERS. FIXINGS SHOULD NOT EXCEED 50MM FROM ANY EDGE AND NOT EXCEED 200MM CENTRES.

DETAIL D - FRAMED OPENING, TWO LAYERS OF KNAUFFIRE BATT SUITABLE FOR UP TO 120 MINUTESINTEGRITY & INSULATION WITHIN KNAUF FIRE RESISTANT SYSTEMSOF UP TO 120 MINUTES INTEGRITY & INSULATION

1. CUT KNAUF FIRE BATT TO TIGHTLY FIT IN TO FRAMED APERTURE.

2. APPLY KNAUF FIRE MASTIC TO EDGES AND FIT IN TO OPENING AT REQUIRED POSITION. APPLY KNAUF FIRE MASTIC BRUSH GRADE TO ONE SIDE OF BOARD, TO BOARD JOINT OR 10mm KNAUF FIRE MASTIC BEAD TO ONE SIDE OF BOARD.

3. REPEAT TO THE OPPOSITE SIDE OF THE WALL. IF REQUIRED.

2. APPLY KNAUF FIRE MASTIC TO EDGES AND FIT IN TOOPENING AT REQUIRED POSITION. APPLY KNAUF FIREMASTIC BRUSH GRADE OR KNAUF FIRE MASTIC GUNGRADE MASTIC TO ONE SIDE OF BOARD TO BOARDJOINT OR 10MM KNAUF FIRE MASTIC BEAD TO ONE SIDEOF BOARD TO BOARD JOINT.

The published fire ratings have beenachieved by following the instructions setout above. Use of alternative componentsor deviations from the instructions in anyway will remove Knauf from any designliability. Knauf will accept no responsibilityfor the consequences of using Knaufproducts in applications or for the purposesnot authorised by Knauf. Expert adviceshould be sought where suchapplications are contemplated.The Information contained within thisdrawing is believed to be correct on thedate of publication, and is based upontested and certified solutions. The policy ofKnauf is one of constant improvement.Installers must therefore ensure that they arefollowing the latest published drawings andinstructions. Whilst Knauf will endeavour tokeep its publications up to date, theaccuracy of the information containedwithin this drawing may be affected bypertinent changes in the law or regulatoryrequirements and alterations oramendments to the specification of Knaufproducts.

KNAUF FIRE MASTIC

KNAUF FIRE BATT

KNAUF PARTITION TO SUIT SPECIFICATION

KNAUF FIRE BATT

KNAUF PARTITION TO SUIT

SPECIFICATION

KNAUF FIRE MASTIC

KNAUF FIRE BATT

KNAUF FIRE BATT

KNAUF FIRE MASTIC

FIXING


KNAUF FIRE MASTIC

KNAUF FIRE BATT

KNAUF FIRE BATT

KNAUF FIRE MASTIC


A

B

C

D

E

F

G

H

I

J

K

L

M

NOTES

PROJECT:

TITLE:

DRN:

DRG. No:

REV. No:

SCALE:

DATE:



KNAUF FIXINGS





KNAUF FLAT PLATE





KNAUF PUTTY PAD


200Pa



PFH1-13

STANDARD DETAILS

SHEET 6 OF 6

NTSTECH

2018 A

1. DETAIL A

The published fire ratings have beenachieved by following the instructions setout above. Use of alternative componentsor deviations from the instructions in anyway will remove Knauf from any designliability. Knauf will accept no responsibilityfor the consequences of using Knaufproducts in applications or for the purposesnot authorised by Knauf. Expert adviceshould be sought where suchapplications are contemplated.The Information contained within thisdrawing is believed to be correct on thedate of publication, and is based upontested and certified solutions. The policy ofKnauf is one of constant improvement.Installers must therefore ensure that they arefollowing the latest published drawings andinstructions. Whilst Knauf will endeavour tokeep its publications up to date, theaccuracy of the information containedwithin this drawing may be affected bypertinent changes in the law or regulatoryrequirements and alterations oramendments to the specification of Knaufproducts.

INSTALLATION INSTRUCTIONS

1. ENSURE WITHIN APERTURE IS CLEAN AND FREE OF DEBRIS LOOSE CEMENT, AND REMOVE ALL DUST FROM SURFACES REQUIRING INSTALLATION.

DETAIL A - 200mm WIDE x 25mm DEPTH ANNULAR TOCOMBUSTIBLE PIPES WITHIN KNAUF PARTITION TO SUITSPECIFICATION UP TO 120 MINUTES INTEGRITY &INSULATION. PLEASE REFER TO TABLE.

1. SELECT CORRECT SIZE POLYETHYLENE TO TIGHTLY FIT INTO MINIMUM 20mm.

2. FORM A RING AROUND THE PIPE WITH POLYETHYLENE BACKER AND FIX THE TWO ENDS TOGETHER WITH TAPE, SLIDE ALONG THE PIPE INTO THE OPENING TO FORM A 25mm DEEP RECESS TO THE FRONT FACE OF WALL. 3. FILL RECESS UNTIL FLUSH WITH WALL AND TROWEL SMOOTH. 4. REPEAT TO THE OPPOSITE SIDE OF THE WALL

Pipe Type Diameter mm Thickness mm Rating

PVC

PE

ABS

401251254011011040

114.3114.3

1.94.88.23.73.46.62.77.2

11.3

EI 120

EI 120EI 120 I 90

EI 120EI 120

EI 120 I 90EI 120 I 90

DETAIL B, D & E - 200 x 100 APERTURE WITHIN KNAUF PARTITION UPTO 120 MINUTES INTEGRITY & INSULATION SUITABLE FORCABLES AND COMBUSTIBLE PIPES UP TO 63mm. PLEASE REFER TO TABLE.

1. ENSURE SERVICES ARE 20mm MINIMUM FROM EDGE OF OPENING PIPES AND CABLE BUNCHES 20mm APART.2. FILL VOID WITH KNAUF EARTHWOOL SLAB RS33 TO FORM A 25mm RECESS TO KNAUF PLASTERBOARD FACE.3. FILL RECESS WITH KNAUF FIRE MASTIC HPE AND TOWEL FLUSH WITH KNAUF PLASTERBOARD FACE.

Penetration Type Dia mm RatingCable Bundle

HDPE w/ 15mm Copper

40mm

5.85.8

EI 120

Type

Type A1Type F

Type A2Type A3Type FType B

EI 120 I 90

Pipe Type Dia mm

Cable

HDPE Gas Pipe

Thickness6363

EI 120EI 120

DETAIL C - 200mm WIDE x 25mm DEPTH ANNULAR TOINSULATED NON-COMBUSTIBLE PIPES.

1. INSTALL AS DETAIL A

Pipe Type Dia mm Thickness mm RatingCopper/Steel

1516040160

15

0.7 to 14

0.7

EI 120

EI 120 I 60

Copper/Steel

Copper/Steel

2 to 140.7 to 142 to 14

Insulation30mm Glass fiber

33mmNitrile

N/A

EI 120 I 90EI 120

EI 120 I 30

DETAIL F - 600 x 140 APERTURE WITHIN KNAUF PARTITION UPTO 120 MINUTES INTEGRITY & INSULATION SUITABLE FORFULLEN CABLE SET

1. INSTALL AS DETAILS B,D & E

Penetration Type Size mm RatingCable Ladders/ Tray Up to 500

Type

VariousUp to EI 120

Full EN Cable set

3. DETAIL C

5. DETAIL E

2. DETAIL B

4. DETAIL D

6. DETAIL F

KNAUF PARTITION TOSUIT SPECIFICATION

POLYETHELENEBACKER

KNAUF FIRE MASTIC HPE

COMPUSTIBLEPIPE


KNAUF EARTHWOOLSLAB RS33

PE (GAS) PIPE

VARIOUS CABLE


INSULETED COPPER/STEEL PLATE

POLYETHELENEBACKER





TELCOM CABLE BUNDLE

VARIOUS CABLE



COPPER WITHINPE (GAS) PIPE


VARIOUS CABLE


FULL EN CABLE SET



CABLE TRAY/LADDER


Documents

NOTES · 2019-02-05 · knauf putty pad system performance: fire : 60:60ei sound: 45db rw max height*:3800mm impact duty**:severe min. ... knauf putty pad. system performance: fire