North/Latin America Europe/Africa ......manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances

LCD TVSERVICE MANUAL

CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : LB01B

MODEL : 42LD450/460 42LD450/460-TAMODEL : 42LD461C 42LD461C-TA

North/Latin America http://aic.lgservice.comEurope/Africa http://eic.lgservice.comAsia/Oceania http://biz.lgservice.com

Internal Use Only

Printed in KoreaP/NO : MFL62865307 (1007-REV01)

LGE Internal Use OnlyCopyright © 2010 LG Electronics. Inc. All rights reserved.Only for training and service purposes

- 2 -

CONTENTS

CONTENTS .............................................................................................. 2

PRODUCT SAFETY ................................................................................. 3

SPECIFICATION ....................................................................................... 6

ADJUSTMENT INSTRUCTION ................................................................ 9

BLOCK DIAGRAM...................................................................................15

EXPLODED VIEW .................................................................................. 16

SVC. SHEET ...............................................................................................


- 3 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in theSchematic Diagram and Exploded View.It is essential that these special safety parts should be replaced with the same components as recommended in this manual to preventShock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during theservicing of a receiver whose chassis is not isolated from the ACpower line. Use a transformer of adequate power rating as thisprotects the technician from accidents resulting in personal injuryfrom electrical shocks.

It will also protect the receiver and it's components from beingdamaged by accidental shorts of the circuitry that may beinadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown,replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor,over 1 W), keep the resistor 10 mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposedmetallic parts of the cabinet, such as antennas, terminals, etc., tobe sure the set is safe to operate without damage of electricalshock.

Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source, connect anelectrical jumper across the two AC plug prongs. Place the ACswitch in the on position, connect one lead of ohm-meter to the ACplug prongs tied together and touch other ohm-meter lead in turn toeach exposed metallic parts such as antenna terminals, phonejacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1 MΩ and 5.2 MΩ. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check.Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using AC voltmeterwith 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat AC voltagemeasurements for each exposed metallic part. Any voltagemeasured must not exceed 0.75 volt RMS which is corresponds to0.5 mA.In case any measurement is out of the limits specified, there ispossibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.

Leakage Current Hot Check circuit

1.5 Kohm/10W

To Instrument'sexposed METALLIC PARTS

Good Earth Groundsuch as WATER PIPE,CONDUIT etc.

AC Volt-meter

When 25A is impressed between Earth and 2nd Groundfor 1 second, Resistance must be less than 0.1*Base on Adjustment standard

IMPORTANT SAFETY NOTICE

0.15 uF

Ω


- 4 -

CAUTION: Before servicing receivers covered by this servicemanual and its supplements and addenda, read and follow theSAFETY PRECAUTIONS on page 3 of this publication.NOTE: If unforeseen circumstances create conflict between thefollowing servicing precautions and any of the safety precautions onpage 3 of this publication, always follow the safety precautions.Remember: Safety First.

General Servicing Precautions1. Always unplug the receiver AC power cord from the AC power

source before;a. Removing or reinstalling any component, circuit board

module or any other receiver assembly.b. Disconnecting or reconnecting any receiver electrical plug or

other electrical connection.c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver.CAUTION: A wrong part substitution or incorrect polarityinstallation of electrolytic capacitors may result in anexplosion hazard.

2. Test high voltage only by measuring it with an appropriate highvoltage meter or other voltage measuring device (DVM,FETVOM, etc) equipped with a suitable high voltage probe.Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of itsassemblies.

4. Unless specified otherwise in this service manual, cleanelectrical contacts only by applying the following mixture to thecontacts with a pipe cleaner, cotton-tipped stick or comparablenon-abrasive applicator; 10 % (by volume) Acetone and 90 %(by volume) isopropyl alcohol (90 % - 99 % strength)CAUTION: This is a flammable mixture.Unless specified otherwise in this service manual, lubrication ofcontacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with whichreceivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of itselectrical assemblies unless all solid-state device heat sinks arecorrectly installed.

7. Always connect the test receiver ground lead to the receiverchassis ground before connecting the test receiver positivelead.Always remove the test receiver ground lead last.

8. Use with this receiver only the test fixtures specified in thisservice manual.CAUTION: Do not connect the test fixture ground strap to anyheat sink in this receiver.

Electrostatically Sensitive (ES) DevicesSome semiconductor (solid-state) devices can be damaged easilyby static electricity. Such components commonly are calledElectrostatically Sensitive (ES) Devices. Examples of typical ESdevices are integrated circuits and some field-effect transistors andsemiconductor "chip" components. The following techniquesshould be used to help reduce the incidence of componentdamage caused by static by static electricity.1. Immediately before handling any semiconductor component or

semiconductor-equipped assembly, drain off any electrostaticcharge on your body by touching a known earth ground.Alternatively, obtain and wear a commercially availabledischarging wrist strap device, which should be removed toprevent potential shock reasons prior to applying power to theunit under test.

2. After removing an electrical assembly equipped with ESdevices, place the assembly on a conductive surface such asaluminum foil, to prevent electrostatic charge buildup orexposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ESdevices.

4. Use only an anti-static type solder removal device. Some solderremoval devices not classified as "anti-static" can generateelectrical charges sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generateelectrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protectivepackage until immediately before you are ready to install it.(Most replacement ES devices are packaged with leadselectrically shorted together by conductive foam, aluminum foilor comparable conductive material).

7. Immediately before removing the protective material from theleads of a replacement ES device, touch the protective materialto the chassis or circuit assembly into which the device will beinstalled.CAUTION: Be sure no power is applied to the chassis or circuit,and observe all other safety precautions.

8. Minimize bodily motions when handling unpackagedreplacement ES devices. (Otherwise harmless motion such asthe brushing together of your clothes fabric or the lifting of yourfoot from a carpeted floor can generate static electricitysufficient to damage an ES device.)

General Soldering Guidelines1. Use a grounded-tip, low-wattage soldering iron and appropriate

tip size and shape that will maintain tip temperature within therange or 500 °F to 600 °F.

2. Use an appropriate gauge of RMA resin-core solder composedof 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.4. Thoroughly clean the surfaces to be soldered. Use a mall wire-

bristle (0.5 inch, or 1.25 cm) brush with a metal handle.Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering techniquea. Allow the soldering iron tip to reach normal temperature.

(500 °F to 600 °F)b. Heat the component lead until the solder melts.c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.CAUTION: Work quickly to avoid overheating the circuitboard printed foil.

6. Use the following soldering technique.a. Allow the soldering iron tip to reach a normal temperature

(500 °F to 600 °F)b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts.c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it thereonly until the solder flows onto and around both thecomponent lead and the foil.CAUTION: Work quickly to avoid overheating the circuitboard printed foil.

d. Closely inspect the solder area and remove any excess orsplashed solder with a small wire-bristle brush.

SERVICING PRECAUTIONS


- 5 -

IC Remove/ReplacementSome chassis circuit boards have slotted holes (oblong) throughwhich the IC leads are inserted and then bent flat against thecircuit foil. When holes are the slotted type, the following techniqueshould be used to remove and replace the IC. When working withboards using the familiar round hole, use the standard techniqueas outlined in paragraphs 5 and 6 above.

Removal1. Desolder and straighten each IC lead in one operation by gently

prying up on the lead with the soldering iron tip as the soldermelts.

2. Draw away the melted solder with an anti-static suction-typesolder removal device (or with solder braid) before removing theIC.

Replacement1. Carefully insert the replacement IC in the circuit board.2. Carefully bend each IC lead against the circuit foil pad and

solder it.3. Clean the soldered areas with a small wire-bristle brush.

(It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete TransistorRemoval/Replacement1. Remove the defective transistor by clipping its leads as close as

possible to the component body.2. Bend into a "U" shape the end of each of three leads remaining

on the circuit board.3. Bend into a "U" shape the replacement transistor leads.4. Connect the replacement transistor leads to the corresponding

leads extending from the circuit board and crimp the "U" withlong nose pliers to insure metal to metal contact then soldereach connection.

Power Output, Transistor DeviceRemoval/Replacement1. Heat and remove all solder from around the transistor leads.2. Remove the heat sink mounting screw (if so equipped).3. Carefully remove the transistor from the heat sink of the circuit

board.4. Insert new transistor in the circuit board.5. Solder each transistor lead, and clip off excess lead.6. Replace heat sink.

Diode Removal/Replacement1. Remove defective diode by clipping its leads as close as

possible to diode body.2. Bend the two remaining leads perpendicular y to the circuit

board.3. Observing diode polarity, wrap each lead of the new diode

around the corresponding lead on the circuit board.4. Securely crimp each connection and solder it.5. Inspect (on the circuit board copper side) the solder joints of

the two "original" leads. If they are not shiny, reheat them and ifnecessary, apply additional solder.

Fuse and Conventional Resistor

Removal/Replacement1. Clip each fuse or resistor lead at top of the circuit board hollow

stake.2. Securely crimp the leads of replacement component around

notch at stake top.3. Solder the connections.

CAUTION: Maintain original spacing between the replacedcomponent and adjacent components and the circuit board toprevent excessive component temperatures.

Circuit Board Foil RepairExcessive heat applied to the copper foil of any printed circuitboard will weaken the adhesive that bonds the foil to the circuitboard causing the foil to separate from or "lift-off" the board. Thefollowing guidelines and procedures should be followed wheneverthis condition is encountered.

At IC ConnectionsTo repair a defective copper pattern at IC connections use thefollowing procedure to install a jumper wire on the copper patternside of the circuit board. (Use this technique only on ICconnections).

1. Carefully remove the damaged copper pattern with a sharpknife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (ifused) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire andcarefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copperpattern and let it overlap the previously scraped end of the goodcopper pattern. Solder the overlapped area and clip off anyexcess jumper wire.

At Other ConnectionsUse the following technique to repair the defective copper patternat connections other than IC Pins. This technique involves theinstallation of a jumper wire on the component side of the circuitboard.

1. Remove the defective copper pattern with a sharp knife.Remove at least 1/4 inch of copper, to ensure that a hazardouscondition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the patternbreak and locate the nearest component that is directlyconnected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of thenearest component on one side of the pattern break to the leadof the nearest component on the other side.Carefully crimp and solder the connections.CAUTION: Be sure the insulated jumper wire is dressed so theit does not touch components or sharp edges.


- 6 -

SPECIFICATIONNOTE : Specifications and others are subject to change without notice for improvement.

1. Application rangeThis specification is applied to the LCD TV used LB01Bchassis.

2. Requirement for TestEach part is tested as below without special appointment.

1) Temperature: 25 ºC ± 5 ºC (77 ºF ± 9 ºF), CST : 40 ºC ± 5 ºC

2) Relative Humidity : 65 % ± 10 %3) Power Voltage

: Standard input voltage (AC 100-240 V~ 50 / 60 Hz)* Standard Voltage of each products is marked by models.

4) Specification and performance of each parts are followedeach drawing and specif ication by part number inaccordance with BOM.

5) The receiver must be operated for about 5 minutes prior tothe adjustment.

3. Test method1) Performance: LGE TV test method followed 2) Demanded other specification

- Safety: CE, IEC specification- EMC:CE, IEC

5. Module optical specifications(1) LGD Module

1) Standard Test Condition (The unit has been ‘ON’)2) Stable for approximately 30 minutes in a dark environment at 25 ºC ± 2 ºC.3) The values specified are at approximate distance 50 cm from the LCD surface.4) Ta = 25 ºC ± 2 °C, VLCD = 12.0 V, fv = 60 Hz, Dclk = 74.25 MHz, VBR_A = 1.65 V, EXTVBR-B = 100 %

No. Item Specification Min. Typ. Max. Remark

1. Viewing Angle (CR > 10) Right/Left/Up/Down 178 Degree

2. Luminance Luminance (cd/m2) 400 500

Variation - 1.3 MAX / MIN

3. Contrast Ratio CR 1100 1500

4. CIE Color Coordinates White Wx 0.279

Wy 0.292

RED Rx 0.636

Ry Typ. 0.335 Typ.

Green Gx -0.03 0.291 +0.03

Gy 0.603

Blue Bx 0.146

By 0.061

- 7 - LGE Internal Use OnlyCopyright © 2010 LG Electronics. Inc. All rights reserved.Only for training and service purposes

6. Component Video Input (Y, CB/PB, CR/PR)

No.Specification

RemarkResolution H-freq(kHz) V-freq(Hz)

1. 720x480 15.73 60.00 SDTV,DVD 480i

2. 720x480 15.63 59.94 SDTV,DVD 480i

3. 720x480 31.47 59.94 480p

4. 720x480 31.50 60.00 480p

5. 720x576 15.625 50.00 SDTV,DVD 625 Line

6. 720x576 31.25 50.00 HDTV 576p

7. 1280x720 45.00 50.00 HDTV 720p

8. 1280x720 44.96 59.94 HDTV 720p

9. 1280x720 45.00 60.00 HDTV 720p

10. 1920x1080 31.25 50.00 HDTV 1080i

11. 1920x1080 33.75 60.00 HDTV 1080i

12. 1920x1080 33.72 59.94 HDTV 1080i

13. 1920x1080 56.250 50 HDTV 1080p

14. 1920x1080 67.5 60 HDTV 1080p

No.Specification

Proposed RemarkResolution H-freq(kHz) V-freq(Hz) Pixel Clock(MHz)

1. 720*400 31.468 70.08 28.321 For only DOS mode

2. 640*480 31.469 59.94 25.17 VESA Input 848*480 60 Hz, 852*480 60 Hz

-> 640*480 60 Hz Display

3. 800*600 37.879 60.31 40.00 VESA

4. 1024*768 48.363 60.00 65.00 VESA(XGA)

5. 1280*768 47.78 59.87 79.5 WXGA

6. 1360*768 47.72 59.8 84.75 WXGA

7. 1280*1024 63.981 60.02 108.875 SXGA FHD Model

8. 1920*1080 66.587 59.93 138.625 WUXGA FHD model

7. RGB (PC)


8. HDMI Input(1) DTV Mode

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1. 720*400 31.468 70.08 28.321 HDCP

2. 640*480 31.469 59.94 25.17 VESA HDCP

3. 800*600 37.879 60.31 40.00 VESA HDCP

4. 1024*768 48.363 60.00 65.00 VESA(XGA) HDCP

5. 1280*768 47.78 59.87 79.5 WXGA HDCP

6. 1360*768 47.72 59.8 84.75 WXGA HDCP

7. 1280*1024 63.981 60.02 108.875 SXGA HDCP/FHD model

8. 1920*1080 67.5 60.00 138.625 WUXGA HDCP/FHD model

(2) PC Mode

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

1. 720*480 31.469 /31.5 59.94 /60 27.00/27.03 SDTV 480P

2. 720*576 31.25 50 54 SDTV 576P

3. 1280*720 37.500 50 74.25 HDTV 720P

4. 1280*720 44.96 /45 59.94 /60 74.17/74.25 HDTV 720P

5. 1920*1080 33.72 /33.75 59.94 /60 74.17/74.25 HDTV 1080I

6. 1920*1080 28.125 50.00 74.25 HDTV 1080I

7. 1920*1080 26.97 /27 23.97 /24 74.17/74.25 HDTV 1080P

8. 1920*1080 33.716 /33.75 29.976 /30.00 74.25 HDTV 1080P

9. 1920*1080 56.250 50 148.5 HDTV 1080P

10. 1920*1080 67.43 /67.5 59.94 /60 148.35/148.50 HDTV 1080P


- 9 -

ADJUSTMENT INSTRUCTION

1. Application RangeThis specification sheet is applied to all of the LCD TV withLB01B chassis.

2. Designation1) The adjustment is according to the order which is

designated and which must be followed, according to theplan which can be changed only on agreeing.

2) Power Adjustment: Free Voltage3) Magnetic Field Condition: Nil.4) Input signal Unit: Product Specification Standard5) Reserve after operation: Above 5 Minutes (Heat Run)

Temperature : at 25 ºC ± 5 ºC Relative humidity : 65 % ± 10 %Input voltage : 220 V, 60 Hz

6) Adjustment equipments: Color Analyzer(CA-210 or CA-110),DDC Adjustment Jig equipment, Service remote control.

7) Push the “IN STOP” key - For memory initialization.

3. Main PCB check process* APC - After Manual-Insult, executing APC

* Boot file Download1) Execute ISP program “Mstar ISP Utility” and then click

“Config” tab.

2) Set as below, and then click “Auto Detect” and check “OK”messageIf “Error” is displayed, Check connection betweencomputer, jig, and set.

3) Click “Read” tab, and then load download file (XXXX.bin)by clicking “Read”

4) Click “Connect” tab. If “Can’t” is displayed, checkconnection between computer, jig, and set.

5) Click “Auto” tab and set as below6) Click “Run”.7) After downloading, check “OK” message.

* USB DOWNLOAD1) Put the USB Stick to the USB socket 2) Automatically detecting update file in USB Stick

- If your downloaded program version in USB Stick is Low,it didn’t work. But your downloaded version is High, USBdata is automatically detecting

3) Show the message “Copying files from memory”

filexxx.bin

(4)

(7) ……….OK

(5)

(6)

(1)

fi lexxx.bin

(2) (3)

Please Check the Speed : To use speed between from 200KHz to 400KHz

Case1 : Software version up1. After downloading S/W by USB, TV set will reboot

automatically2. Push “In-stop” key3. Push “Power on” key4. Function inspection5. After function inspection, Push “In-stop” key.

Case2 : Function check at the assembly line1. When TV set is entering on the assembly line, Push

“In-stop” key at first.2. Push “Power on” key for turning it on.

-> If you push “Power on” key, TV set will recoverchannel information by itself.

3. After function inspection, Push “In-stop” key.

4) Updating is staring.

5) Uploading completed, The TV will restart automatically.6) If your TV is turned on, check your updated version and

Tool option.(explain the Tool option, next stage)* If downloading version is more high than your TV have,

TV can lost all channel data. In this case, you have tochannel recover. if all channel data is cleared, you didn’thave a DTV/ATV test on production line.

* After downloading, have to adjust Tool Option again.1) Push "IN-START" key in service remote control.2) Select “Tool Option 1” and Push “OK” button.3) Punch in the number. (Each model has their number)

4) Completed selecting Tool option.

3.1. ADC Process(1) ADC

- Enter Service Mode by pushing “ADJ” key,- Enter Internal ADC mode by pushing “G” key at “5. ADC

Calibration”

<Caution> Using ‘power on’ button of the Adjustment R/C,power on TV.

* ADC Calibration Protocol (RS232)

Adjust Sequence• aa 00 00 [Enter Adjust Mode]• xb 00 40 [Component1 Input (480i)]• ad 00 10 [Adjust 480i Comp1]• xb 00 60 [RGB Input (1024*768)]• ad 00 10 [Adjust 1024*768 RGB]• aa 00 90 End Adjust mode* Required equipment : Adjustment R/C.

3.2. Function Check* Check display and sound

- Check Input and Signal items. (cf. work instructions)1) TV2) AV (SCART1/SCART2/ CVBS)3) COMPONENT (480i)4) RGB (PC : 1024 x 768 @ 60 Hz)5) HDMI6) PC Audio In* Display and Sound check is executed by Remote control.


Module Tool option1 Tool option2 Tool option3 Tool option4 Tool option5

LGD 25313 10770 52228 26892 32

CMO 25317 10770 52228 26892 32

No Item CMD1 CMD2 Data0

Enter Adjust Adjust A A 0 0 When transfer the ‘Mode In’,

Mode ‘Mode In’ Carry the command.

ADC adjust ADC Adjust A D 1 0 Automatically adjustment

(The use of a internal pattern)

4. Total Assembly line process4.1. Adjustment Preparation

· W/B Equipment conditionCA210 : CH 9, Test signal : Inner pattern (85IRE)

· Above 5 minutes H/run in the inner pattern. (“power on” keyof adjust remote control)

* Connecting picture of the measuring instrument(On Automatic control)Inside PATTERN is used when W/B is controlled. Connect toauto controller or push Adjustment R/C POWER ON ->Enter the mode of White-Balance, the pattern will come out.

* Auto-control interface and directions1) Adjust in the place where the influx of light like floodlight

around is blocked. (illumination is less than 10 lux).2) Adhere closely the Color Analyzer (CA210) to the module

less than 10 cm distance, keep it with the surface of theModule and Color Analyzer’s prove vertically.(80° ~ 100°).

3) Aging time- After aging start, keep the power on (no suspension of

power supply) and heat-run over 5 minutes.- Using ‘no signal’ or ‘full white pattern’ or the others,

check the back light on.

• Auto adjustment Map(RS-232C)RS-232C COMMAND[CMD ID DATA]

Wb 00 00 White Balance StartWb 00 ff White Balance End

<Caution>Color Temperature : COOL, Medium, Warm. One of R Gain/G Gain/ B Gain should be kept on 0xC0, andadjust other two lower than C0.(when R/G/B Gain are all C0, it is the FULL Dynamic Rangeof Module)

* Manual W/B process using adjusts Remote control.• After enter Service Mode by pushing “ADJ” key,• Enter White Balance by pushing “G” key at “6. White

Balance”.

* After done all adjustments, Press “In-start” button andcompare Tool option and Area option value with its BOM, ifit is correctly same then unplug the AC cable. If it is notsame, then correct it same with BOM and unplug AC cable.For correct it to the model’s module from factory Jig model.

* Push the “IN STOP” key after completing the functioninspection. And Mechanical Power Switch must be set“ON”.

4.2. DDC EDID Write (RGB 128Byte )• Connect D-sub Signal Cable to D-sub Jack.• Write EDID Data to EEPROM(24C02) by using DDC2B

protocol.• Check whether written EDID data is correct or not.* For SVC main Assembly, EDID have to be downloaded to

Insert Process in advance.

4.3. DDC EDID Write (HDMI 256Byte)• Connect HDMI Signal Cable to HDMI Jack.• Write EDID Data to EEPROM(24C02) by using DDC2B

protocol.• Check whether written EDID data is correct or not.* For SVC main Assembly, EDID have to be downloaded to

Insert Process in advance.

4.4. EDID DATA1) All Data : HEXA Value2) Changeable Data :*: Serial No : Controlled / Data:01**: Month : Controlled / Data:00***:Year : Controlled****:Check sum


Cool 13,000 K X=0.269(±0.002)

Y=0.273(±0.002) <Test Signal>

Medium 9,300 K X=0.285(±0.002) Inner pattern

Y=0.293(±0.002) (216gray,85IRE)

Warm 6,500 K X=0.313(±0.002)

Y=0.329(±0.002)

Full White Pattern

COLORANALYZERTYPE: CA-210

RS-232C Communication

CA-210

RS-232C COMMAND MIN CENTER MAX

[CMD ID DATA] (DEFAULT)

Cool Mid Warm Cool Mid Warm

R Gain jg Ja jd 00 172 192 192 192

G Gain jh Jb je 00 172 192 192 192

B Gain ji Jc jf 00 192 192 172 192

R Cut 64 64 64 128

G Cut 64 64 64 128

B Cut 64 64 64 128

4.5. Auto Download1) Press Adj. key on the Adj. Remote control.2) Select EDID D/L menu.3) By pressing Enter key, EDID download will begin4) If Download is successful, OK is display, but If Download if

failure, NG is displayed.5) If Download is failure, Re-try downloads.

* Edid data and Model option download (RS232)

- Manual Download* Caution

1) Use the proper signal cable for EDID Download- Analog EDID : Pin3 exists- Digital EDID : Pin3 exists

2) Never connect HDMI & D-sub Cable at the same time.3) Use the proper cables below for EDID Writing4) Download HDMI1, HDMI2, separately because HDMI1 is

different from HDMI2

1) FHD RGB EDID data

2) FHD HDMI EDID data

* Detail EDID Options are below Product ID

Serial No: Controlled on production line.

Month, Year: Controlled on production line:ex) Monthly : ‘02’ -> ‘01’

Year : ‘2010’ -> ‘14’ Model Name(Hex):

Checksum: Changeable by total EDID data.

Vendor Specific(HDMI)

Model Name HEX EDID Table DDC Function

FHD Model 0001 01 00 Analog/Digital


- 12 -

MODEL MODEL NAME(HEX)

all 00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20

Item

Manufacturer ID

Version

Revision

Condition

GSM

Digital : 1

Digital : 3

Data(Hex)

1E6D

01

03

D-sub to D-sub DVI-D to HDMI or HDMI to HDMI

For HDMI EDIDFor Analog EDID

INPUT MODEL NAME(HEX)

HDMI1 67030C001000B82D

HDMI2 67030C002000B82D

HDMI3 67030C003000B82D

HDMI4 67030C004000B82D

0 1 2 3 4 5 6 7 8 9 A B C D E F

00 00 FF FF FF FF FF FF 00 1E 6D a b

10 c 01 03 68 10 09 78 0A EE 91 A3 54 4C 99 26

20 0F 50 54 A1 08 00 81 80 61 40 45 40 31 40 01 01

30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C

40 45 00 A0 5A 00 00 00 1E 01 1D 00 72 51 D0 1E 20

50 6E 28 55 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A

60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d

70 d 00 e

80 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

90 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

A0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

B0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

C0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

D0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

E0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

F0 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0 1 2 3 4 5 6 7 8 9 A B C D E F

00 00 FF FF FF FF FF FF 00 1E 6D a b

10 c 01 03 80 10 09 78 0A EE 91 A3 54 4C 99 26

20 0F 50 54 A1 08 00 71 4F 81 01 01 01 01 01 01 01

30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C

40 45 00 A0 5A 00 00 00 1E 01 1D 00 72 51 D0 1E 20

50 6E 28 55 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A

60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d

70 d 01 e

80 02 03 26 F1 4E 10 1F 84 13 05 14 03 02 12 20 21

90 22 15 01 26 15 07 50 09 57 07 f

A0 f E3 05 03 01 01 1D 80 18 71 1C 16 20 58 2C

B0 25 00 A0 5A 00 00 00 9E 01 1D 00 80 51 D0 0C 20

C0 40 80 35 00 A0 5A 00 00 00 1E 02 3A 80 18 71 38

D0 2D 40 58 2C 45 00 A0 5A 00 00 00 1E 66 21 50 B0

E0 51 00 1B 30 40 70 36 00 A0 5A 00 00 00 1E 00 00

F0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 F9

NO Item CMD1 CMD2 Data0

Enter Download A A 0 0 When transfer the ‘Mode In’,

download Mode ‘Mode In’ Carry the command.

EDID data Download A E 00 10 Automatically Download

and Model (The use of a internal pattern)

option download


4.5. V-COM Adjust(Only LGD(M+S) Module)- Why need Vcom adjustment?A The Vcom (Common Voltage) is a Reference Voltage of

Liquid Crystal Driving.-> Liquid Crystal need for Polarity Change with every frame.

- Adjust sequence· Press the PIP key of th ADJ remote control.(This PIP key ishot key to enter the VCOM adjusting mode)(Or After enter Service Mode by pushing “ADJ” key, thenEnter V-Com Adjust mode by pushing “G” key at “10. V-Com”

· As pushing the right or the left key on the remote control,and find the V-COM value which is no or minimized theFlicker. (If there is no flicker at default value, Press the exitkey and finish the VCOM adjustment.)

· Push the “OK” key to store value. Then the message“Saving OK” is pop.

· Press the exit key to finish VCOM adjustment.

(Visual Adjust and control the Voltage level)

4.6. Outgoing condition Configuration- When pressing IN-STOP key by SVC remocon, Red LED are

blinked alternatively. And then Automatically turn off.(Must not AC power OFF during blinking)

4.7. Internal pressureConfirm whether is normal or not when between powerboard’s ac block and GND is impacted on 1.5 kV(dc) or 2.2kV(dc) for one second.

5. Model name & Serial number D/L• Press “Power on” key of service remocon.

(Baud rate : 115200 bps)• Connect RS232 Signal Cable to RS-232 Jack.• Write Serial number by use RS-232.• Must check the serial number at the Diagnostics of SET UP

menu. (Refer to below).

5.1. Signal TABLE

CMD : A0hLENGTH : 85~94h (1~16 bytes)ADH : EEPROM Sub Address high (00~1F)ADL : EEPROM Sub Address low (00~FF)Data : Write dataCS : CMD + LENGTH + ADH + ADL + Data_1 +…+ Data_nDelay : 20ms

5.2. Command Set

* DescriptionFOS Default write : <7mode data> writeVtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0,PhaseData write : Model Name and Serial Number write in

EEPROM,.

5.3. Method & noticeA. Serial number D/L is using of scan equipment.B. Setting of scan equipment operated by Manufacturing

Technology Group.C. Serial number D/L must be conformed when it is produced

in production line, because serial number D/L is mandatoryby D-book 4.0.

* Manual Download (Model Name and Serial Number)If the TV set is downloaded by OTA or Service man, Sometimesmodel name or serial number is initialized.(Not always)There is impossible to download by bar code scan, so It needManual download.1) Press the ‘instart’ key of ADJ remote controller.2) Go to the menu ‘5.Model Number D/L’ like below photo.3) Input the Factory model name(ex 42LD450-ZA) or Serial

number like photo.

CMD LENGTH ADH ADL DATA_1 . . . Data_n CS DELAY

No. Adjust mode CMD(hex) LENGTH(hex) Description

1 EEPROM WRITE A0h 84h+n n-bytes Write (n = 1~16)

Row Line

Column Line

CLC CST

Panel

S

Y

S

T

E

M

Gat

e D

rive

IC

So urce D r iv e I C

Circuit Block

Ti m in g Cont r o ll er

Po w er Blo ck

VCOM

GammaRe f er ence V o ltage

Gamm a ReferenceVolta ge

Data (R,G,B) & C ont ro l s ignal

Cont rol si gnal

Data (R,G,B ) &Cont rol si gnal

Inte

rfac

e

TFT

Po w er I n p u tPower Input

Da t a I n pu tDa t a I n pu t

VCOM

Liquid Crys tal

VCOM

4) Check the model name Instart menu -> Factory namedisplayed (ex 42LD450-ZA)

5) Check the Diagnostics (DTV country only) -> Buyer modeldisplayed (ex 42LD450)

6. CI+ key download(Only for CI model)6-1. Download Procedure

(1) Press "Power on" button of a service R/C.(Baud rate :115200 bps)

(2) Connect RS232-C Signal Cable.(3) Write CI+ Key through RS-232-C.(4) Check whether the key was downloaded or not at ‘In Start’

menu. (Refer to below).

=> Check the Download to CI+ Key value in LGset.

6-2. check the method of CI+ Key value(1) Check the method on Instart menu

(2) check the method of RS232C Command 1) into the main ass’y mode (RS232 : aa 00 00)

2) check the key download for transmitted command(RS232 : ci 00 10)

3) result value- normally status for download : OKx- abnormally status for download : NGx

6-3. Check the method of CI+ key value (RS232)(1) into the main ass’y mode (RS232 : aa 00 00)

(2) Check the method of CI+ key by command(RS232 : ci 00 20)

(3) Result valuei 01 OK 1d1852d21c1ed5dcx


CMD 1 CMD 2 Data 0

A A 0 0

CMD 1 CMD 2 Data 0

C I 1 0

CMD 1 CMD 2 Data 0

A A 0 0

CMD 1 CMD 2 Data 0

C I 2 0

CI+ key Value


BLOCK DIAGRAM

- 16 - LGE Internal Use OnlyCopyright LG Electronics. Inc. All rights reserved.Only for training and service purposes

300

200

530

810

400

510

120

500 A

4A

2A

5A

10

A21

900

910

800

LV1

LV2

540

521

EXPLODED VIEW

Many electrical and mechanical parts in this chassis have special safety-related characteristics. Theseparts are identified by in the Schematic Diagram and EXPLODED VIEW. It is essential that these special safety parts should be replaced with the same components asrecommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

IMPORTANT SAFETY NOTICE

THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATESSPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTHE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC.

PCM_A[8]

CI_TS_DATA[6]

PCM_A[3]

PCM_A[10]

FE_TS_DATA[5]

PCM_A[0]

PCM_D[6]

CI_TS_DATA[0]

PCM_D[2]

PCM_A[7]

PCM_A[9]

FE_TS_DATA[3]

PCM_A[12]

PCM_A[4]

PCM_D[5]

CI_TS_DATA[3]

PCM_A[5]

FE_TS_DATA[0]

CI_TS_DATA[5]

PCM_A[2]

PCM_A[13]

FE_TS_DATA[4]

PCM_A[1]

PCM_A[3]

PCM_A[2]

CI_TS_DATA[4]

PCM_D[1]

PCM_A[11]

FE_TS_DATA[2]

PCM_D[4]

PCM_A[7]

PCM_A[6]

PCM_A[0]

CI_TS_DATA[7]

PCM_A[4]

PCM_D[0]

FE_TS_DATA[6]

CI_TS_DATA[1]

CI_TS_DATA[2]

PCM_A[6]

PCM_A[14]

PCM_D[3]

PCM_D[7]

FE_TS_DATA[1]

FE_TS_DATA[7]

PCM_A[5]

PCM_A[1]

MODEL_OPT_2

/PCM_WE

R104

10K

OPT

HP_DET

S7_RXD

I2C_SDA

SPI_SDI

FRC_RESET

+3.3V_Normal

I2C_SDA

/PF_OE

PCM_A[0-7]

+3.5V_ST

C1048pFOPT

C1080.1uFOPT

IC103CAT24WC08W-T

3A2

2A1

4VSS

1A0

5 SDA

6 SCL

7 WP

8 VCC

TUNER_RESET

FRC_PWM1

CI_TS_DATA[0-7]

R158 100

OPT

M_REMOTE_RX

R1051K

OPT

UART_FRC_TX

R1081K

OPT

DEMOD_RESET

PCM_D[0-7]

R126

1K

PF_ALE

PF_ALE

SPI_SCK

IC102HY27UF082G2B-TPCB

2GBIT

26NC_17

27NC_18

28NC_19

29I/O0

30I/O1

31I/O2

32I/O3

33NC_20

34NC_21

35NC_22

36VSS_2

37VCC_2

38NC_23

39NC_24

40NC_25

41I/O4

42I/O5

43I/O6

44I/O7

45NC_26

46NC_27

47NC_28

48NC_29

17ALE

3NC_3

6NC_6

16CLE

15NC_10

14NC_9

13VSS_1

12VCC_1

11NC_8

10NC_7

9CE

8RE

7R/B

4NC_4

5NC_5

25NC_16

24NC_15

23NC_14

2NC_2

22NC_13

21NC_12

1NC_1

20NC_11

19WP

18WE

/PCM_WAIT

R125

1K

OPT

DSUB_DET

R1134.7K

M_REMOTE_TX

USB1_OCD

/PF_WE

FE_TS_VAL_ERR

R115

1K

ERROR_OUT

R134 22

R159 100

OPT

CI_TS_SYNC

SC1/COMP1_DET

A_DIM

/PCM_REG

FE_TS_SYNC

PCM_5V_CTL

S7_TXD

5V_DET_HDMI_4

R128 22

+3.3V_Normal

/PCM_IRQA

+5V_Normal

/PF_OE

C1112.2uF

FRC_SCL

R118

1K

OPT

SC_RE1

/PCM_IOWR

R1030

SCAN_BLK1/OPC_OUT

/PF_CE1

SPI_SDO

C107

0.1uF

R14922

M_REMOTE

/PCM_IORD

5V_DET_HDMI_3

PWM2

C1050.1uF

C1030.1uF

/PF_WE

R135 22

I2C_SDA

5V_DET_HDMI_2

ET_RXER

R124

1K

MODEL_OPT_3

R120

1K

OPT

C1068pFOPT

FRC_PWM0

R123

1K

OPT

R14633

/PF_CE1

/PF_CE0

R101

3.3K

OPT

AV_CVBS_DET

RGB_DDC_SDA

PWM0

MODEL_OPT_1

I2C_SCL

R14822M_REMOTE

CI_TS_VAL

PCM_A[0-14]

R13310K

I2C_SCL

/F_RB

/RST_PHY

R1550

OPT

PWM_DIM

/PCM_OE

UART_FRC_RX

Q101KRC103SOPT

E

B

C

R106

1K

R138 22

FE_TS_DATA[0-7]

PCM_RST

R117

1K

/PF_WP

I2C_SCL

SCAN_BLK2

SC_RE2

R116

1K

OPT

+3.3V_Normal

R107

1K

R157 100

R13210K

R137 22

CI_TS_CLK

SIDEAV_DET

/PF_CE0

IC102-*1HY27US08121B-TPCB

512MBIT

26NC_17

27NC_18

28NC_19

29I/O0

30I/O1

31I/O2

32I/O3

33NC_20

34NC_21

35NC_22

36VSS_2

37VCC_2

38PRE

39NC_23

40NC_24

41I/O4

42I/O5

43I/O6

44I/O7

45NC_25

46NC_26

47NC_27

48NC_28

17ALE

3NC_3

6NC_6

16CLE

15NC_10

14NC_9

13VSS_1

12VCC_1

11NC_8

10NC_7

9CE

8RE

7R/B

4NC_4

5NC_5

25NC_16

24NC_15

23NC_14

2NC_2

22NC_13

21NC_12

1NC_1

20NC_11

19WP

18WE

/PCM_CD

/F_RB

C1010.1uF

R139 22

5V_DET_HDMI_1

/SPI_CS

/PCM_CE

/PF_WP

R109

3.9K

C1090.1uF

R127 4.7K

+3.3V_Normal

USB1_CTL

MODEL_OPT_0

PWM0

FRC_SDA

R129 22

PWM1

+3.3V_Normal

PWM2

WIRELESS_DL_RX

R136 22

RGB_DDC_SCL

WIRELESS_DL_TX

R121

1K

FE_TS_CLK

R102

3.3K

R14733

R15133

PWM0

PWM1

AUD_LRCH

AUD_MASTER_CLK

AUD_SCK

+3.3V_Normal

R111 22

R112 22

R156 10K

/FLASH_WP

/RST_HUB

C10210uF

P3903

12505WS-03A00

URSA_DEBUG

1

2

3

4

P3904

12505WS-03A00

URSA_DEBUG

1

2

3

4

NEC_SDA

I2C_SDA

I2C_SCL

AMP_SCL

R142

3.3K

R145

2.2K

R143

3.3K

R144

2.2K

AMP_SDA

+3.3V_Normal

NEC_SCL

CONTROL_ATTEN

R1601K

/PIF_SPI_CS

IC104M24M01-HRMN6TP

3E2

2E1

4VSS

1NC

5SDA

6SCL

7WP

8VCC

AR104

22AR103

22

AR101

22

AR102

22

R141

1K

R140

1K

R1100

R1500

MODEL_OPT_6

IC102-*2NAND01GW3B2CN6E

1GBIT

26NC_17

27NC_18

28NC_19

29I/O0

30I/O1

31I/O2

32I/O3

33NC_20

34NC_21

35NC_22

36VSS_2

37VDD_2

38NC_23

39NC_24

40NC_25

41I/O4

42I/O5

43I/O6

44I/O7

45NC_26

46NC_27

47NC_28

48NC_29

17AL

3NC_3

6NC_6

16CL

15NC_10

14NC_9

13VSS_1

12VDD_1

11NC_8

10NC_7

9E

8R

7RB

4NC_4

5NC_5

25NC_16

24NC_15

23NC_14

2NC_2

22NC_13

21NC_12

1NC_1

20NC_11

19WP

18W

LGE107D (S7M Divx_Non RM)

IC101

S7M_DIVX & MS10

PCM_D0U22

PCM_D1T21

PCM_D2T22

PCM_D3AB18

PCM_D4AC18

PCM_D5AC19

PCM_D6AC20

PCM_D7AC21

PCM_A0U21

PCM_A1V21

PCM_A2Y22

PCM_A3AA22

PCM_A4R22

PCM_A5R21

PCM_A6T23

PCM_A7T24

PCM_A8AA23

PCM_A9Y20

PCM_A10AB17

PCM_A11AA21

PCM_A12U23

PCM_A13Y23

PCM_A14W23

PCM_REG_NW22

PCM_OE_NAA17

PCM_WE_NV22

PCM_IORD_NW21

PCM_IOWR_NY21

PCM_CE_NAA20

PCM_IRQA_NV23

PCM_CD_NP23

PCM_WAIT_NR23

PCM_RESETP22

PCM_PF_CE0ZAC17

PCM_PF_CE1ZAB20

PCM_PF_OEZAA18

PCM_PF_WEZAB21

PCM_PF_ALEAB19

PCM_PF_AD[15]AD17

PCM_PF_RBZAA19

UART_TX2/GPIO65M23

UART_RX2/GPIO64N23

DDCR_DA/GPIO71M22

DDCR_CK/GPIO72N22

DDCA_DA/UART0_TXA5

DDCA_CK/UART0_RXB5

PWM0/GPIO66K23

PWM1/GPIO67K22

PWM2/GPIO68G23

PWM3/GPIO69G22

PWM4/GPIO70G21

SAR0/GPIO31C6

SAR1/GPIO32B6

SAR2/GPIO33C8

SAR3/GPIO34C7

SAR4/GPIO35A6

GPIO143/TCON0N21

GPIO145/TCON2M21

GPIO147/TCON4L22

GPIO149/TCON6L21

GPIO151/TCON8P21

GPIO36/UART3_RXK21

GPIO37/UART3_TXL23

GPIO38K20

GPIO39L20

GPIO40M20

GPIO41G20

GPIO42G19

GPIO50/UART1_RXF20

GPIO51/UART1_TXF19

GPIO6/PM0/INT0E7

GPIO7/PM1/PM_UART_TXD7

GPIO8/PM2E11

GPIO9/PM3G9

GPIO10/PM4F9

GPIO11/PM5/PM_UART_RX/INT1C5

PM_SPI_CS1/GPIO12/PM6E8

PM_SPI_WP1/GPIO13/PM7E9

PM_SPI_WP2/GPIO14/PM8/INT2F7

GPIO15/PM9F6

PM_SPI_CS2/GPIO16/PM10D8

GPIO17/PM11/INT3G12

GPIO18/PM12/INT4F10

PM_SPI_CK/GPIO1D9

GPIO0/PM_SPI_CZD11

PM_SPI_DI/GPIO2E10

PM_SPI_DO/GPIO3D10

TS0_CLKAA9

TS0_VLDAA5

TS0_SYNCAA10

TS0_D0AB5

TS0_D1AC4

TS0_D2Y6

TS0_D3AA6

TS0_D4W6

TS0_D5AA7

TS0_D6Y9

TS0_D7AA8

TS1_CLKAC5

TS1_VLDAC6

TS1_SYNCAB6

TS1_D0AC10

TS1_D1AB10

TS1_D2AC9

TS1_D3AB9

TS1_D4AC8

TS1_D5AB8

TS1_D6AC7

TS1_D7AB7

MPIF_CLKD12

MPIF_CS_ND14

MPIF_BUSYE14

MPIF_D0E12

MPIF_D1F12

MPIF_D2D13

MPIF_D3E13

LGE101D (S7 Non_Tcon/RM)IC101-*8

S7_DIVX & MS10

NC_48AE1

NC_78AF16

NC_64AF1

NC_50AE3

NC_45AD14

NC_34AD3

NC_77AF15

NC_65AF2

NC_62AE15

NC_33AD2

NC_47AD16

NC_46AD15

NC_63AE16

NC_66AF3

NC_76AF14

NC_32AD1

NC_44AD13

NC_61AE14

NC_60AE13

NC_51AE4

NC_36AD5

NC_67AF4

NC_35AD4

NC_49AE2

NC_71AF8

NC_40AD9

NC_56AE9

NC_72AF9

NC_58AE11

NC_69AF6

NC_53AE6

NC_74AF11

NC_37AD6

NC_43AD12

NC_52AE5

NC_75AF12

NC_68AF5

NC_59AE12

NC_57AE10

NC_70AF7

NC_42AD11

NC_38AD7

NC_41AD10

NC_54AE7

NC_73AF10

NC_39AD8

NC_55AE8

NC_12Y11

GND_105Y19

LVACLKP/LLV6P/BLUE[3]W26

LVACLKN/LLV6N/BLUE[2]W25

LVA0P/LLV3P/BLUE[9]U26

LVA0N/LLV3N/BLUE[8]U25


LVA1N/LLV4N/BLUE[6]V26

LVA2P/LLV5P/BLUE[5]V25


LVA3P/LLV7P/BLUE[1]W24

LVA3N/LLV7N/BLUE[0]Y26

LVA4P/LLV8PY25

LVA4N/LLV8NY24

LVBCLKP/LLV0P/GREEN[5]AC26

LVBCLKN/LLV0N/GREEN[4]AC25

LVB0P/RLV6P/RED[1]AA26

LVB0N/RLV6N/RED[0]AA25

LVB1P/RLV7P/GREEN[9]AA24

LVB1N/RLV7N/GREEN[8]AB26

LVB2P/RLV8P/GREEN[7]AB25


LVB3P/LLV1P/GREEN[3]AC24

LVB3N/LLV1N/GREEN[2]AD26

LVB4P/LLV0P/GREEN[1]AD25


RLV3P/RED[7]AD23

RLV3N/RED[6]AE23

RLV0P/LVSYNCAE26

RLV0N/LHSYNCAE25

RLV1N/LCKAF26

RLV2P/RED[9]AF25

RLV1P/LDEAE24

RLV2N/RED[8]AF24

RLV4P/RED[5]AF23

RLV4N/RED[4]AD22

RLV5P/RED[3]AE22

RLV5N/RED[2]AF22

TCON3/OE/GOE/GCLK2AD19

TCON15/SCAN_BLK1AE19

TCON18/CS7/GCLK5AD21

TCON19/CS8/GCLK6AE21

TCON11/CS5/HCONAF21

TCON10/CS4/OPT_NAD20

TCON9/CS3/OPT_PAE20

TCON16/WPWMAF20

TCON12/DPMAF19

TCON1/STV/GSP/VSTAD18

TCON5/TP/SOEAE18

TCON14/SACN_BLKAF18

TCON21/CS10/VGH_ODDAB22

TCON20/CS9/VGH_EVENAB23

TCON13/LEDONAC23

TCON17/CS6/GCLK4AC22

NC_26AB16

NC_19AA14

NC_30AC15

NC_15Y16

NC_31AC16

NC_29AC14

NC_21AA16

NC_20AA15

NC_11Y10

NC_17AA11

NC_25AB15

NC_24AB14

LGE105D(S7-Tcon Divx_ Non_RM)IC101-*4

S7T_DIVX & MS10

NC_43AE1

NC_73AF16

NC_59AF1

NC_45AE3

NC_40AD14

NC_29AD3

NC_72AF15

NC_60AF2

NC_57AE15

NC_28AD2

NC_42AD16

NC_41AD15

NC_58AE16

NC_61AF3

NC_71AF14

NC_27AD1

NC_39AD13

NC_56AE14

NC_55AE13

NC_46AE4

NC_31AD5

NC_62AF4

NC_30AD4

NC_44AE2

NC_66AF8

NC_35AD9

NC_51AE9

NC_67AF9

NC_53AE11

NC_64AF6

NC_48AE6

NC_69AF11

NC_32AD6

NC_38AD12

NC_47AE5

NC_70AF12

NC_63AF5

NC_54AE12

NC_52AE10

NC_65AF7

NC_37AD11

NC_33AD7

NC_36AD10

NC_49AE7

NC_68AF10

NC_34AD8

NC_50AE8

NC_12Y11

GND_105Y19

RLV3PW26

RLV3NW25

RLV0PU26

RLV0NU25

RLV1PU24

RLV1NV26

RLV2PV25

RLV2NV24

RLVCKPW24

RLVCKNY26

RLV4PY25

RLV4NY24

WPWMAC26

OPTP/FLK2AC25

RLV5PAA26

RLV5NAA25

RLV6PAA24

RLV6NAB26

RLV7PAB25

RLV7NAB24

OPTN/FLK3AC24

FLKAD26

GCLK6AD25

GCLK5AD24

LLV3PAD23

LLV3NAE23

LLV0PAE26

LLV0NAE25

LLV1PAF26

LLV1NAF25

LLV2PAE24

LLV2NAF24

LLVCKPAF23

LLVCKNAD22

LLV4PAE22

LLV4NAF22

GOE/GCLK1AD19

GSC/GCLK3AE19

LLV5PAD21

LLV5NAE21

LLV6PAF21

LLV6NAD20

LLV7PAE20

LLV7NAF20

GSPRAF19

GSP/VSTAD18

SOEAE18

POLAF18

VDD_ODDAB22

VDD_EVENAB23

GCLK4AC23

GCLK2AC22

NC_23AB16

DPMAA14

HCONAC15

NC_15Y16

NC_26AC16

LEDONAC14

NC_20AA16

NC_19AA15

NC_11Y10

NC_17AA11

SCAN_BLKAB15

SCAN_BLK1AB14

LGE101 (S7 NON_TON/DiX/RM)IC101-*10

S7_NON_DIVX & MS10

NC_48AE1

NC_78AF16

NC_64AF1

NC_50AE3

NC_45AD14

NC_34AD3

NC_77AF15

NC_65AF2

NC_62AE15

NC_33AD2

NC_47AD16

NC_46AD15

NC_63AE16

NC_66AF3

NC_76AF14

NC_32AD1

NC_44AD13

NC_61AE14

NC_60AE13

NC_51AE4

NC_36AD5

NC_67AF4

NC_35AD4

NC_49AE2

NC_71AF8

NC_40AD9

NC_56AE9

NC_72AF9

NC_58AE11

NC_69AF6

NC_53AE6

NC_74AF11

NC_37AD6

NC_43AD12

NC_52AE5

NC_75AF12

NC_68AF5

NC_59AE12

NC_57AE10

NC_70AF7

NC_42AD11

NC_38AD7

NC_41AD10

NC_54AE7

NC_73AF10

NC_39AD8

NC_55AE8

NC_12Y11

GND_105Y19











LVA4P/LLV8PY25

LVA4N/LLV8NY24













RLV3P/RED[7]AD23

RLV3N/RED[6]AE23

RLV0P/LVSYNCAE26

RLV0N/LHSYNCAE25

RLV1N/LCKAF26

RLV2P/RED[9]AF25

RLV1P/LDEAE24

RLV2N/RED[8]AF24

RLV4P/RED[5]AF23

RLV4N/RED[4]AD22

RLV5P/RED[3]AE22

RLV5N/RED[2]AF22





TCON11/CS5/HCONAF21


TCON9/CS3/OPT_PAE20

TCON16/WPWMAF20

TCON12/DPMAF19


TCON5/TP/SOEAE18

TCON14/SACN_BLKAF18



TCON13/LEDONAC23


NC_26AB16

NC_19AA14

NC_30AC15

NC_15Y16

NC_31AC16

NC_29AC14

NC_21AA16

NC_20AA15

NC_11Y10

NC_17AA11

NC_25AB15

NC_24AB14

LGE105 (S7-Tcon Non_Divx/RM)IC101-*6

S7T_NON_DIVX & MS10

NC_43AE1

NC_73AF16

NC_59AF1

NC_45AE3

NC_40AD14

NC_29AD3

NC_72AF15

NC_60AF2

NC_57AE15

NC_28AD2

NC_42AD16

NC_41AD15

NC_58AE16

NC_61AF3

NC_71AF14

NC_27AD1

NC_39AD13

NC_56AE14

NC_55AE13

NC_46AE4

NC_31AD5

NC_62AF4

NC_30AD4

NC_44AE2

NC_66AF8

NC_35AD9

NC_51AE9

NC_67AF9

NC_53AE11

NC_64AF6

NC_48AE6

NC_69AF11

NC_32AD6

NC_38AD12

NC_47AE5

NC_70AF12

NC_63AF5

NC_54AE12

NC_52AE10

NC_65AF7

NC_37AD11

NC_33AD7

NC_36AD10

NC_49AE7

NC_68AF10

NC_34AD8

NC_50AE8

NC_12Y11

GND_105Y19

RLV3PW26

RLV3NW25

RLV0PU26

RLV0NU25

RLV1PU24

RLV1NV26

RLV2PV25

RLV2NV24

RLVCKPW24

RLVCKNY26

RLV4PY25

RLV4NY24

WPWMAC26

OPTP/FLK2AC25

RLV5PAA26

RLV5NAA25

RLV6PAA24

RLV6NAB26

RLV7PAB25

RLV7NAB24

OPTN/FLK3AC24

FLKAD26

GCLK6AD25

GCLK5AD24

LLV3PAD23

LLV3NAE23

LLV0PAE26

LLV0NAE25

LLV1PAF26

LLV1NAF25

LLV2PAE24

LLV2NAF24

LLVCKPAF23

LLVCKNAD22

LLV4PAE22

LLV4NAF22

GOE/GCLK1AD19

GSC/GCLK3AE19

LLV5PAD21

LLV5NAE21

LLV6PAF21

LLV6NAD20

LLV7PAE20

LLV7NAF20

GSPRAF19

GSP/VSTAD18

SOEAE18

POLAF18

VDD_ODDAB22

VDD_EVENAB23

GCLK4AC23

GCLK2AC22

NC_23AB16

DPMAA14

HCONAC15

NC_15Y16

NC_26AC16

LEDONAC14

NC_20AA16

NC_19AA15

NC_11Y10

NC_17AA11

SCAN_BLKAB15

SCAN_BLK1AB14

LGE107 (S7M Non Divx/RM)IC101-*2

S7M_NON_DIVX & MS10

FRC_DDR3_A0/DDR2_NCAE1

FRC_DDR3_A1/DDR2_A6AF16


FRC_DDR3_A3/DDR2_A1AE3

FRC_DDR3_A4/DDR2_CASZAD14

FRC_DDR3_A5/DDR2_A10AD3








FRC_DDR3_BA0/DDR2_BA2AF3

FRC_DDR3_BA1/DDR2_ODTAF14

FRC_DDR3_BA2/DDR2_A12AD1

FRC_DDR3_MCLK/DDR2_MCLKAD13

FRC_DDR3_CKE/DDR2_RASZAE14

FRC_DDR3_MCLKZ/DDR2_MCLKZAE13

FRC_DDR3_ODT/DDR2_BA1AE4

FRC_DDR3_RASZ/DDR2_WEZAD5

FRC_DDR3_CASZ/DDR2_CKEAF4

FRC_DDR3_WEZ/DDR2_BA0AD4

FRC_DDR3_RESETB/DDR2_A3AE2

FRC_DDR3_DQSL/DDR2_DQS0AF8

FRC_DDR3_DQSLB/DDR2_DQSB0AD9

FRC_DDR3_DQSU/DDR2_DQS1AE9

FRC_DDR3_DQSUB/DDR2_DQSB1AF9

FRC_DDR3_DML/DDR2_DQ7AE11

FRC_DDR3_DMU/DDR2_DQ11AF6

FRC_DDR3_DQL0/DDR2_DQ6AE6

FRC_DDR3_DQL1/DDR2_DQ0AF11

FRC_DDR3_DQL2/DDR2_DQ1AD6



FRC_DDR3_DQL5/DDR2_NCAF12



FRC_DDR3_DQU0/DDR2_DQ8AE10

FRC_DDR3_DQU1/DDR2_DQ14AF7

FRC_DDR3_DQU2/DDR2_DQ13AD11





FRC_DDR3_DQU7/DDR2_DQM1AD8

FRC_DDR3_NC/DDR2_DQM0AE8

FRC_REXTY11

FRC_TESTPINY19

ACKP/RLV3P/RED[3]W26

ACKM/RLV3N/RED[2]W25

A0P/RLV0P/RED[9]U26

A0M/RLV0N/RED[8]U25

A1P/RLV1P/RED[7]U24

A1M/RLV1N/RED[6]V26

A2P/RLV2P/RED[5]V25

A2M/RLV2N/RED[4]V24

A3P/RLV4P/RED[1]W24

A3M/RLV4N/RED[0]Y26

A4P/RLV5P/GREEN[9]Y25

A4M/RLV5N/GREEN[8]Y24

BCKP/TCON13/GREEN[1]AC26

BCKM/TCON12/GREEN[0]AC25

B0P/RLV6P/GREEN[7]AA26

B0M/RLV6N/GREEN[6]AA25


B1M/RLV7N/GREEN[4]AB26

B2P/RLV8P/GREEN[3]AB25


B3P/TCON11/BLUE[9]AC24

B3M/TCON10/BLUE[8]AD26

B4P/TCON9/BLUE[7]AD25


CCKP/LLV3PAD23

CCKM/LLV3NAE23

C0P/LLV0P/BLUE[5]AE26

C0M/LLV0N/BLUE[4]AE25

C1P/LLV1P/BLUE[3]AF26

C1M/LLV1N/BLUE[2]AF25



C3P/LLV4PAF23

C3M/LLV4NAD22

C4P/LLV5PAE22

C4M/LLV5NAF22

DCKP/TCON5AD19

DCKM/TCON4AE19

D0P/LLV6PAD21

D0M/LLV6NAE21

D1P/LLV7PAF21

D1M/LLV7NAD20

D2P/LLV8PAE20

D2M/LLV8NAF20

D3P/TCON3AF19

D3M/TCON2AD18

D4P/TCON1AE18

D4M/TCON0AF18

GPIO0/TCON15/HSYNC/VDD_ODDAB22

GPIO1/TCON14/VSYNC/VDD_EVENAB23

GPIO2/TCON7/LDE/GCLK4AC23

GPIO3/TCON6/LCK/GCLK2AC22

FRC_GPIO0/UART_RXAB16

FRC_GPIO1AA14

FRC_GPIO3AC15

FRC_GPIO8Y16

FRC_GPIO9/UART_TXAC16

FRC_GPIO10AC14

FRC_I2CM_DAAA16

FRC_I2CM_CKAA15

FRC_I2CS_DAY10

FRC_I2CS_CKAA11

FRC_PWM0AB15

FRC_PWM1AB14

LGE107DB-LF-1 (S7M Divx_Non RM/MS10)IC101-*1

S7M_DIVX & DD
















































FRC_REXTY11

FRC_TESTPINY19



A0P/RLV0P/RED[9]U26

A0M/RLV0N/RED[8]U25

A1P/RLV1P/RED[7]U24

A1M/RLV1N/RED[6]V26

A2P/RLV2P/RED[5]V25

A2M/RLV2N/RED[4]V24

A3P/RLV4P/RED[1]W24

A3M/RLV4N/RED[0]Y26















CCKP/LLV3PAD23

CCKM/LLV3NAE23







C3P/LLV4PAF23

C3M/LLV4NAD22

C4P/LLV5PAE22

C4M/LLV5NAF22

DCKP/TCON5AD19

DCKM/TCON4AE19

D0P/LLV6PAD21

D0M/LLV6NAE21

D1P/LLV7PAF21

D1M/LLV7NAD20

D2P/LLV8PAE20

D2M/LLV8NAF20

D3P/TCON3AF19

D3M/TCON2AD18

D4P/TCON1AE18

D4M/TCON0AF18






FRC_GPIO1AA14

FRC_GPIO3AC15

FRC_GPIO8Y16


FRC_GPIO10AC14

FRC_I2CM_DAAA16

FRC_I2CM_CKAA15

FRC_I2CS_DAY10

FRC_I2CS_CKAA11

FRC_PWM0AB15

FRC_PWM1AB14

LGE107B-LF-1 (S7M Non Divx/RM/MS10)IC101-*3

S7M_NON_DIVX & DD
















































FRC_REXTY11

FRC_TESTPINY19



A0P/RLV0P/RED[9]U26

A0M/RLV0N/RED[8]U25

A1P/RLV1P/RED[7]U24

A1M/RLV1N/RED[6]V26

A2P/RLV2P/RED[5]V25

A2M/RLV2N/RED[4]V24

A3P/RLV4P/RED[1]W24

A3M/RLV4N/RED[0]Y26















CCKP/LLV3PAD23

CCKM/LLV3NAE23







C3P/LLV4PAF23

C3M/LLV4NAD22

C4P/LLV5PAE22

C4M/LLV5NAF22

DCKP/TCON5AD19

DCKM/TCON4AE19

D0P/LLV6PAD21

D0M/LLV6NAE21

D1P/LLV7PAF21

D1M/LLV7NAD20

D2P/LLV8PAE20

D2M/LLV8NAF20

D3P/TCON3AF19

D3M/TCON2AD18

D4P/TCON1AE18

D4M/TCON0AF18






FRC_GPIO1AA14

FRC_GPIO3AC15

FRC_GPIO8Y16


FRC_GPIO10AC14

FRC_I2CM_DAAA16

FRC_I2CM_CKAA15

FRC_I2CS_DAY10

FRC_I2CS_CKAA11

FRC_PWM0AB15

FRC_PWM1AB14

LGE105DB-LF-1 (S7-Tcon Divx_ Non_RM/MS10)IC101-*5

S7T_DIVX & DD

NC_43AE1

NC_73AF16

NC_59AF1

NC_45AE3

NC_40AD14

NC_29AD3

NC_72AF15

NC_60AF2

NC_57AE15

NC_28AD2

NC_42AD16

NC_41AD15

NC_58AE16

NC_61AF3

NC_71AF14

NC_27AD1

NC_39AD13

NC_56AE14

NC_55AE13

NC_46AE4

NC_31AD5

NC_62AF4

NC_30AD4

NC_44AE2

NC_66AF8

NC_35AD9

NC_51AE9

NC_67AF9

NC_53AE11

NC_64AF6

NC_48AE6

NC_69AF11

NC_32AD6

NC_38AD12

NC_47AE5

NC_70AF12

NC_63AF5

NC_54AE12

NC_52AE10

NC_65AF7

NC_37AD11

NC_33AD7

NC_36AD10

NC_49AE7

NC_68AF10

NC_34AD8

NC_50AE8

NC_12Y11

GND_105Y19

RLV3PW26

RLV3NW25

RLV0PU26

RLV0NU25

RLV1PU24

RLV1NV26

RLV2PV25

RLV2NV24

RLVCKPW24

RLVCKNY26

RLV4PY25

RLV4NY24

WPWMAC26

OPTP/FLK2AC25

RLV5PAA26

RLV5NAA25

RLV6PAA24

RLV6NAB26

RLV7PAB25

RLV7NAB24

OPTN/FLK3AC24

FLKAD26

GCLK6AD25

GCLK5AD24

LLV3PAD23

LLV3NAE23

LLV0PAE26

LLV0NAE25

LLV1PAF26

LLV1NAF25

LLV2PAE24

LLV2NAF24

LLVCKPAF23

LLVCKNAD22

LLV4PAE22

LLV4NAF22

GOE/GCLK1AD19

GSC/GCLK3AE19

LLV5PAD21

LLV5NAE21

LLV6PAF21

LLV6NAD20

LLV7PAE20

LLV7NAF20

GSPRAF19

GSP/VSTAD18

SOEAE18

POLAF18

VDD_ODDAB22

VDD_EVENAB23

GCLK4AC23

GCLK2AC22

NC_23AB16

DPMAA14

HCONAC15

NC_15Y16

NC_26AC16

LEDONAC14

NC_20AA16

NC_19AA15

NC_11Y10

NC_17AA11

SCAN_BLKAB15

SCAN_BLK1AB14

LGE105B-LF-1 (S7-Tcon Non_Divx/RM/MS10)IC101-*7

S7T_NON_DIVX & DD

NC_43AE1

NC_73AF16

NC_59AF1

NC_45AE3

NC_40AD14

NC_29AD3

NC_72AF15

NC_60AF2

NC_57AE15

NC_28AD2

NC_42AD16

NC_41AD15

NC_58AE16

NC_61AF3

NC_71AF14

NC_27AD1

NC_39AD13

NC_56AE14

NC_55AE13

NC_46AE4

NC_31AD5

NC_62AF4

NC_30AD4

NC_44AE2

NC_66AF8

NC_35AD9

NC_51AE9

NC_67AF9

NC_53AE11

NC_64AF6

NC_48AE6

NC_69AF11

NC_32AD6

NC_38AD12

NC_47AE5

NC_70AF12

NC_63AF5

NC_54AE12

NC_52AE10

NC_65AF7

NC_37AD11

NC_33AD7

NC_36AD10

NC_49AE7

NC_68AF10

NC_34AD8

NC_50AE8

NC_12Y11

GND_105Y19

RLV3PW26

RLV3NW25

RLV0PU26

RLV0NU25

RLV1PU24

RLV1NV26

RLV2PV25

RLV2NV24

RLVCKPW24

RLVCKNY26

RLV4PY25

RLV4NY24

WPWMAC26

OPTP/FLK2AC25

RLV5PAA26

RLV5NAA25

RLV6PAA24

RLV6NAB26

RLV7PAB25

RLV7NAB24

OPTN/FLK3AC24

FLKAD26

GCLK6AD25

GCLK5AD24

LLV3PAD23

LLV3NAE23

LLV0PAE26

LLV0NAE25

LLV1PAF26

LLV1NAF25

LLV2PAE24

LLV2NAF24

LLVCKPAF23

LLVCKNAD22

LLV4PAE22

LLV4NAF22

GOE/GCLK1AD19

GSC/GCLK3AE19

LLV5PAD21

LLV5NAE21

LLV6PAF21

LLV6NAD20

LLV7PAE20

LLV7NAF20

GSPRAF19

GSP/VSTAD18

SOEAE18

POLAF18

VDD_ODDAB22

VDD_EVENAB23

GCLK4AC23

GCLK2AC22

NC_23AB16

DPMAA14

HCONAC15

NC_15Y16

NC_26AC16

LEDONAC14

NC_20AA16

NC_19AA15

NC_11Y10

NC_17AA11

SCAN_BLKAB15

SCAN_BLK1AB14

LGE101DB-LF-1 (S7 Non_Tcon/RM/MS10)IC101-*9

S7_DIVX & DD

NC_48AE1

NC_78AF16

NC_64AF1

NC_50AE3

NC_45AD14

NC_34AD3

NC_77AF15

NC_65AF2

NC_62AE15

NC_33AD2

NC_47AD16

NC_46AD15

NC_63AE16

NC_66AF3

NC_76AF14

NC_32AD1

NC_44AD13

NC_61AE14

NC_60AE13

NC_51AE4

NC_36AD5

NC_67AF4

NC_35AD4

NC_49AE2

NC_71AF8

NC_40AD9

NC_56AE9

NC_72AF9

NC_58AE11

NC_69AF6

NC_53AE6

NC_74AF11

NC_37AD6

NC_43AD12

NC_52AE5

NC_75AF12

NC_68AF5

NC_59AE12

NC_57AE10

NC_70AF7

NC_42AD11

NC_38AD7

NC_41AD10

NC_54AE7

NC_73AF10

NC_39AD8

NC_55AE8

NC_12Y11

GND_105Y19











LVA4P/LLV8PY25

LVA4N/LLV8NY24













RLV3P/RED[7]AD23

RLV3N/RED[6]AE23

RLV0P/LVSYNCAE26

RLV0N/LHSYNCAE25

RLV1N/LCKAF26

RLV2P/RED[9]AF25

RLV1P/LDEAE24

RLV2N/RED[8]AF24

RLV4P/RED[5]AF23

RLV4N/RED[4]AD22

RLV5P/RED[3]AE22

RLV5N/RED[2]AF22





TCON11/CS5/HCONAF21


TCON9/CS3/OPT_PAE20

TCON16/WPWMAF20

TCON12/DPMAF19


TCON5/TP/SOEAE18

TCON14/SACN_BLKAF18



TCON13/LEDONAC23


NC_26AB16

NC_19AA14

NC_30AC15

NC_15Y16

NC_31AC16

NC_29AC14

NC_21AA16

NC_20AA15

NC_11Y10

NC_17AA11

NC_25AB15

NC_24AB14

LGE101B-LF-1(S7 Non_Tcon/Divx/RM/MS10)IC101-*11

S7_NON_DIVX & DD

NC_48AE1

NC_78AF16

NC_64AF1

NC_50AE3

NC_45AD14

NC_34AD3

NC_77AF15

NC_65AF2

NC_62AE15

NC_33AD2

NC_47AD16

NC_46AD15

NC_63AE16

NC_66AF3

NC_76AF14

NC_32AD1

NC_44AD13

NC_61AE14

NC_60AE13

NC_51AE4

NC_36AD5

NC_67AF4

NC_35AD4

NC_49AE2

NC_71AF8

NC_40AD9

NC_56AE9

NC_72AF9

NC_58AE11

NC_69AF6

NC_53AE6

NC_74AF11

NC_37AD6

NC_43AD12

NC_52AE5

NC_75AF12

NC_68AF5

NC_59AE12

NC_57AE10

NC_70AF7

NC_42AD11

NC_38AD7

NC_41AD10

NC_54AE7

NC_73AF10

NC_39AD8

NC_55AE8

NC_12Y11

GND_105Y19











LVA4P/LLV8PY25

LVA4N/LLV8NY24













RLV3P/RED[7]AD23

RLV3N/RED[6]AE23

RLV0P/LVSYNCAE26

RLV0N/LHSYNCAE25

RLV1N/LCKAF26

RLV2P/RED[9]AF25

RLV1P/LDEAE24

RLV2N/RED[8]AF24

RLV4P/RED[5]AF23

RLV4N/RED[4]AD22

RLV5P/RED[3]AE22

RLV5N/RED[2]AF22





TCON11/CS5/HCONAF21


TCON9/CS3/OPT_PAE20

TCON16/WPWMAF20

TCON12/DPMAF19


TCON5/TP/SOEAE18

TCON14/SACN_BLKAF18



TCON13/LEDONAC23


NC_26AB16

NC_19AA14

NC_30AC15

NC_15Y16

NC_31AC16

NC_29AC14

NC_21AA16

NC_20AA15

NC_11Y10

NC_17AA11

NC_25AB15

NC_24AB14

FLASH/EEPROM/GPIO

GP2_Saturn7M

DIMMING

URSA degug port

for WIRELESS READY

for SERIAL FLASH

/PF_CE0H : Serial FlashL : NAND Flash/PF_CE1H : 16 bitL : 8 bit

Boot from SPI flash : 1’b0Boot from NOR flash : 1’b1

Addr:10101--

I2C

A0’h

<T3 CHIP Config>(AUD_SCK, AUD_MASTER_CLK, PWM1, PWM0)

EEPROM

<T3 CHIP Config(AUD_LRCH)>

for ETHERNET PHY

HDCP EEPROM

NAND FLASH MEMORY

from CI SLOT

TO SCART1

MIPS_no_EJ_NOR8 : 4’h3 (MIPS as host. No EJ PAD. Byte mode NAND flash.)MIPS_EJ1_NOR8 : 4’h4 (MIPS as host. EJ use PAD1. Byte mode NAND flash.)MIPS_EJ2_NOR8 : 4’h5 (MIPS as host. EJ use PAD2. Byte mode NAND flash.)B51_Secure_no scramble : 4’hb (8051 as host. Internal SPI flash secure boot, no scramble)B51_Sesure_scramble : 4’hc (8051 as host. Internal SPI flash secure boot with scarmble)

for SYSTEM/HDCP EEPROM&URSA3

Internal demod out/External demod in

$0.199

Ver. 1.3

1

LD650 Scan

& MS10 :Region that support MS10(ex:DTV Country)

& DD :Region that support only Dolby Digital(ex:AISA Analog/KOREA)

Copyright © 2010 LG Electronics. Inc. All rights reserved.Only for training and service purposes LGE Internal Use Only


+3.5V_ST

OCD1B

R1018 22

OCD1A

+3.5V_ST

SIDE_HP_MUTE

R1080

22

MODEL1_OPT_2

POWER_ON/OFF1

R1062

22NON_M_REMOTE

R1060 22

M_REMOTE

OCD1B

C10030.1uF

NEC_RXD

R1036

22

KEY1

+3.5V_ST

R1067 22

R1048 22

R1081 22

TP1001

RL_ON

OCD1A

R1043

22

R1059 22

NON_M_REMOTE

IR

WIRELESS_DETECT

R1065 22R1073 10K

POWER_ON/OFF2_2

CEC_REMOTE_NEC

IC1002

UPD78F0513AGA-GAM-AX

NEC_MICOM

1P60/SCL0

2P61/SDA0

3P62/EXSCL0

4P63

5P33/TI51/TO51/INTP4

6P75

7P74

8P73/KR3

9P72/KR2

10P71/KR1

11P70/KR0

12P32/INTP3/OCD1B

13

P31/INTP2/OCD1A

14

P30/INTP1

15

P17/TI50/TO50

16

P16/TOH1/INTP5

17

P15/TOH0

18

P14/RXD6

19

P13/TXD6

20

P12/SO10

21

P11/SL10/RXD0

22

P10/SCK10/TXD0

23

AVREF

24

AVSS

25 ANI7/P2726 ANI6/P2627 ANI5/P2528 ANI4/P2429 ANI3/P2330 ANI2/P2231 ANI1/P2132 P20/ANI033 P13034 P01/TI010/TO0035 P00/TI00036 P140/PCL/INTP6

37

P120/INTP0/EXLVI

38

P41

39

P40

40

RESET

41

P124/XT2/EXCLKS

42

P123/XT1

43

FLMD0

44

P122/X2/EXCLK/OCD0B

45

P121/X1/OCD0A

46

REGC

47

VSS

48

VDD

FLMD0

+3.5V_ST

R1019 22

R1051 22

R1023 22

R1041

22

SCART1_MUTE

POWER_DET

R1061

22M_REMOTE

NEC_ISP_Tx

P100112505WS-12A00

MICOM_DEBUG

1

2

3

4

5

6

7

8

9

10

11

12

13

OCD1B

POWER_ON/OFF2_1

NEC_ISP_Rx

R1007 100

SW1001JTP-1127WEM

12

4 3

IC1001M24C16-WMN6T

3NC_3

2NC_2

4VSS

1NC_1

5SDA

6SCL

7WC

8VCC

R1076 22

NEC_SCL

C1009

1uF

+3.5V_ST

MODEL1_OPT_3

R1037

22

Q10012SC3052

E

B

C

NEC_ISP_Rx

GND

R1069

22

+3.5V_ST

MODEL1_OPT_1

MICOM_RESET

C1002

0.1uF

OLP

RF_RESET

R1014

4.7K

R1001

47K

TP1002

R1054 22 19-22_LAMP

LED_B/LG_LOGO

R1039

22

R1070 100

FLMD0

WIRELESS_PWR_EN

NEC_EEPROM_SDA

NEC_SDA

INV_CTL

NEC_EEPROM_SDA

TP1003

R1005 10KAMP_MUTE

NEC_ISP_Rx

AMP_RESET_N

NEC_ISP_Tx

MICOM_RESET

R1049 22

OPT

PANEL_CTL

KEY2

OCD1A

R1072 10K

R1063 22

MODEL1_OPT_3R1056 22

C1006

0.1uF

R1064 22

MODEL1_OPT_0

+3.5V_ST

R1066 22

R1008

22

+3.5V_ST

+3.5V_ST

NEC_EEPROM_SCL

R1050 10K

MODEL1_OPT_0

R1015

4.7K

R1068

22

NEC_ISP_Tx

NEC_EEPROM_SCL

RF_ENABLE

R1046

47K

OPC_EN

EDID_WP

R1010 22

R1013 22

MODEL1_OPT_1

R1044 10K

OPT

R1045 10K

OPT

R1057 22

R1078 22

LED_R/BUZZ

R1006 10K

NEC_TXD

SOC_RESET

R1002 10K

R1083 10K

OPT

R1084

10K

OPT

+3.5V_ST

R1086

47K

OPT

+3.5V_ST

R1089

20K

1/16W

1%

R1047 20K

1/16W1%

R1034

4.7MCRYSTAL_KDS

R1071

10K

B/L_LED

R1011

10K

TACT_KEY

R1004

10K

PWM_LED

R1012

10K

B/L_LAMP

R1009

10K

PWM_BUZZ/IIC_LED

R1075

10K

TOUCH_KEY

R1074

10K

NON_GPIO_LED

R1079

10K

GPIO_LED

R1090 22

MODEL1_OPT_2

WIRELESS_SW_CTRL

R1030

10K

R1091 10K

CEC_ON/OFFR1003 0

R1020 0

R1052 10K

C1010

0.1uF

R1055 22

X1002-*132.768KHz

CRYSTAL_EPSON

C1008

15pF

C1007

15pF

X1002

32.768KHz

CRYSTAL_KDS

MICOM

GP2_Saturn7M Ver. 1.4

for Debugger

MICOM MODEL OPTION

EEPROM for Micom

5

B/L_LED

PIN NO.

11

HIGH

MODEL OPTION

B/L_LAMP

MODEL_OPT_2

MODEL_OPT_0

LOWPIN NAME

MODEL_OPT_1

8

MODEL_OPT_3

30

31 GPIO_LED NON_GPIO_LED

TOUCH_KEY TACT_KEY

PWM_LEDPWM_BUZZ/IIC_LED

MODEL_OPT_1 MODEL_OPT_2MODEL_OPT_0 MODEL_OPT_3

LOW LOW LOW LOW

LOW LOW

LOW

LOWLOWLOW

HIGH HIGH

HIGH HIGH HIGH

HIGH

HIGH HIGHLOW LOW

LD350/450/550

19/22/26LE3300(5500)

32/37/42/47/55LE5300(10)

LD420

LE7300

HIGH HIGH TBD


Fiber Optic


C1125OPT

OPT

DSUB_R-

D1116

5.6VOPT

SPDIF_OUT

090:T20

+3.3V_Normal

C112718pF50V

R114210K

D1113

30V

JK1104

SPG09-DB-010

1RED

2GREEN

3BLUE

4GND_1

5DDC_GND

6RED_GND

7GREEN_GND

8BLUE_GND

9NC

10

SYNC_GND

11

GND_2

12

DDC_DATA

13

H_SYNC

14

V_SYNC

15

DDC_CLOCK

16SHILED

R110815K

DSUB_G-

D11175.6V

D111030V

EDID_WP

D1114

5.6VOPT

DSUB_G+

C1108100pF50V

C112668pF50VOPT

D111130V

R112622

OPT

DSUB_HSYNC

C112818pF50V

RGB_DDC_SCL

R11380

R110715K

R11360

R1103470K

PC_R_IN 090:S13R11404.7K

DSUB_R+

R111110K

D1101

5.6VOPT

AMOTECH

C11170.1uF16VOPTR1102

470K

DSUB_B-

IC1105

AT24C02BN-10SU-1.8

3A2

2A1

4GND

1A0

5SDA

6SCL

7WP

8VCC

JK1103

JST1223-0011

GND

2

VCC

3

VINPUT

4FIX_POLE

C11290.1uF16V

R11394.7K

+3.3V_Normal

C1121100pF50V

R11471K

C1123OPT

OPT

RGB_DDC_SDA

DSUB_B+

DSUB_VSYNC

D110930V

R111010K

C1107100pF50V

D1102

5.6VOPT

AMOTECH

C1124OPT

OPT

C112268pF50VOPT

+5V_Normal

R114322

D1115ENKMC2838-T112

A1

C

A2

PC_L_IN 090:S13

IC1104NL17SZ00DFT2G

OPT

3GND

2B

4Y

1A

5VCC

R11340

DSUB_DET

D111230V

R11480

R11500

R114610K

R11270

C1131

0.1uF16V

R114122

R1152

4.7K

OPT

Q1103MMBT3904-(F)

E

B

C

HP_ROUT

090:V8

+3.5V_STR1130

10K

C11151000pF50VOPT

SIDE_HP_MUTE

C11161000pF50VOPT

+3.3V_Normal

SPK_R-_HOTEL

052:I22

SPK_R+_HOTEL

052:I22

HP_DET

R11551K

HP_LOUT

090:V9

Q1101MMBT3904-(F)

E

B

C

Q1102MMBT3904-(F)

E

B

C

C111910uF16V

EXCEPT_CHINA_HOTEL_OPT

C111810uF16V

EXCEPT_CHINA_HOTEL_OPT

Q1104MMBT3904-(F)

E

B

C

R11251K

R11281K

R113375

R113575

R113775

JK1102

PEJ027-01

6B T_TERMINAL2

7B B_TERMINAL2

5 T_SPRING

4 R_SPRING

7A B_TERMINAL1

6A T_TERMINAL1

3 E_SPRING

R11120

R11130

JK3301KJA-PH-0-0177

3DETECT

4L

5GND

1R

Q1105

ISA1530AC1

E

B

C

Q11062SC3052

E

B

CR11293.3K

COMMON AREA

GP2_Saturn7M

5.15 Mstar Circuit Application

PC AUDIO RGB PCSPDIF OPTIC JACK

COMMON AREA

Ver. 1.0

New Item DevelopmentEARPHONE BLOCK

9



C1101 0.33uF

C11050.1uF

R1157 0

R1156 0

R1124100

NEC_RXD

C11060.1uF

+3.5V_ST

R1153 0

R1154 0

D1108

30VCDS3C30GTH

IR_OUT

C11030.1uF

S7_TXD1

D1107

30VCDS3C30GTH

R1114

4.7KOPT

NEC_TXD

IC1101

MAX3232CDR

EAN41348201

3C1-

2V+

4C2+

1C1+

6V-

5C2-

7DOUT2

8RIN2

9ROUT2

10DIN2

11DIN1

12ROUT1

13RIN1

14DOUT1

15GND

16VCC

C11040.1uF

R11094.7KOPT

C11020.1uF

+3.5V_ST

S7_RXD1

R1123100

R11220

OPT

JK1101

SPG09-DB-009

1

2

3

4

5

6

7

8

9

10

JP1121

JP1122

RS232C

RS232C 9PIN

Ver. 1.0GP2_Saturn7M

10



SIDEAV_R_IN

SIDEAV_L_IN

D33025.6V

SIDE_AV_OPT

R3306

10K

SIDE_AV_OPT

R330812K

SIDE_AV_OPT

SIDEAV_CVBS_IN

D33045.6V

SIDE_AV_OPT

R3307

10K

SIDE_AV_OPT

C3303100pF50V

SIDE_AV_OPT

L3303BLM18PG121SN1D

SIDE_AV_OPT

D330130V

SIDE_AV_OPT

L3301BLM18PG121SN1D

SIDE_AV_OPT

R33051K

SIDE_AV_OPT

R3302

10KSIDE_AV_OPT

C3302100pF50V

SIDE_AV_OPTD33035.6V

SIDE_AV_OPT

+3.3V_Normal

R3304470K

SIDE_AV_OPT

R3303

470K

SIDE_AV_OPT

R330912K

SIDE_AV_OPT

L3302BLM18PG121SN1D

SIDE_AV_OPT

C3301100pF

SIDE_AV_OPT

C3304100pFOPT

SIDEAV_DET

R330175

SIDE_AV_OPT

JK3302

PPJ235-01

SIDE_AV_OPT

4A [YL]O-SPRING

5A [YL]E-LUG

3A [YL]CONTACT

4B [WH]O-SPRING

3C [RD]CONTACT

4C [RD]O-SPRING

5C [RD]E-LUG

GP2_Saturn7M

SIDE AV

Ver. 1.0

(New Item Developmen H:9.2mm)SIDE_AV

11


USB DOWN STREAM


SIGN6409

R1453 0

D1452

5.6VCDS3C05HDMI1

OPT

JK1450

KJA-UB-4-0004

12

34

5

L1451

MLB-201209-0120P-N2

120-ohm

SIDE_USB_DP

SIDE_USB_DM

R1452 0

TP1451

D1451

5.6VCDS3C05HDMI1

OPT

/RST_HUB

C1451

22uF

10V

IC1450AP2191SG-13

3IN_2

2IN_1

4EN

1GND

5FLG

6OUT_1

7OUT_2

8NC

C145210uF10V

+5V_USB

C1453

0.1uF

R14554.7KOPT

+3.3V_Normal

R1456 0

USB1_CTL

R145410K

R1451 47 USB1_OCD

USB_DIODES

$0.077



B-MA0

A-TMDML

A-TMWEB

B-TMDQU6

A-MDQL2

A-MDQU4

B-TMDQL3

A-MDQSLB

B-TMDQU6

B-TMA7

A-TMCKE

A-TMCKB

B-MDMU

C1236

0.1uF

A-MDQSLB

A-MA10

A-TMA10

B-TMCKB

A-TMA3

B-TMDQSUB

B-TMWEB

B-TMA3

A-TMODT

A-TMDQU0

A-TMDQSU

B-TMDQL6

B-TMCKE

A-TMBA1 B-MODT

B-MDQU2

B-MVREFDQ

B-MDQL0

B-TMA5

B-TMCASB

B-TMBA1

VCC_1.5V_DDR

A-MBA0

A-TMDQU6

A-MDQU2

A-MDQL7

B-MDQSLB

A-MVREFCA

B-MA9

B-MA2

A-MDQL3

A-MODT

B-MDQL4

A-TMDQU0

B-TMA13

A-MCKB

A-TMDQL7

B-TMDQU2

B-MRASB

B-TMDQU4

B-MDQU6A-TMDQU3

B-MA7

B-MDQU7

B-TMDQL4

A-TMA2

A-MDQL0

B-TMODT

A-MDQSU

L1201

A-MBA1

B-MDQU6

A-TMODT

B-MWEB

B-MDQL6

A-MCKE

A-TMDQL1

A-TMA12

A-MDQL1

C1231

0.1uF

B-MVREFCA

A-TMRASB

B-MDQL1

A-TMDQL7

A-TMDQL6

A-MDQU7

A-MDQU6

C1227

0.1uF

A-MDQL3

B-MCASB

A-MDQU3

B-TMA10

B-TMA11

+1.5V_DDR

A-TMCK

A-MDQL4

B-MA5

B-TMODT

B-TMA12

A-MCK

C1239

0.1uF

A-TMA2

A-MA9

C1221

0.1uF

B-MDQL2

A-TMDQL0

B-TMDQU7

A-MCASB

B-TMDQU3

B-TMA1

A-MDQL6

B-MA8

B-MA3

A-TMCK

B-MDQU1

C1238

0.1uF

C1244

0.1uF

B-MA12

A-TMRASB

A-MA3

A-TMRESETB

B-TMRASB

A-MA5

A-TMDQL4

C12260.1uF16V

A-MVREFDQ

C1202 1000pF

B-MDQL4

C1230

0.1uF

A-MA11

C1235

0.1uF

R1202

1K

1%

A-TMCASB

A-MA2

B-TMA7

R1224

1K1%

A-MCK

B-MCK

B-MDQU5

A-MDQU5 A-TMDQU2

B-TMCASB

B-TMA4

B-TMDQL0

C1219

0.1uF

B-TMDQL7

C1201

0.1uF

B-TMDQL4

B-TMDQL2

B-MODT

C1206

0.1uF

B-TMCK

B-TMDQU1

B-TMDQL2

C1224

0.1uF

A-MDQU6

R1228

1K

1%

B-TMDQU0

C1232

0.1uF

B-MDQU7

A-MA9

A-TMA0

A-MDQL1

B-TMDQL5

R1203

2401%

B-TMA6

C1242

0.1uF

B-MA9

B-TMDQL1

A-TMA4

B-TMA12

A-MODT

B-TMDML

B-MDQSUB

B-TMA3

B-MVREFCA

B-MA5

A-MDQSL

A-MA1

B-TMDMU

A-TMDQSL

B-MBA0

C1203

0.1uF

C1237

0.1uF

B-MA12

VCC_1.5V_DDR

A-TMDQL1

A-MA11

B-MCKE

B-MDQSU

B-MDQL7

B-MA4

B-MA4

R1227

1K1%

A-TMDQSLB

A-MDQU1

B-MDQU5

A-TMCKB

A-TMA6

A-MA6

C1223

0.1uF

VCC_1.5V_DDR

A-TMA8

C1248

0.1uF

B-TMA4

B-MDQL2

A-TMRESETB

C12471000pF

B-MDQU2

A-TMDMU

B-TMA9

B-MDQU0

B-TMRESETB

B-TMDQU2

A-TMDMU

B-MA13

C1241

0.1uF

A-MA0

B-TMA8

A-TMDQL5

A-TMDQU6

A-MA4

A-TMDQL3

A-MDML

B-MDQL3

B-MDQU3

B-TMBA0

VCC_1.5V_DDR

R1204

1K1%

A-MRESETB

A-MWEB

A-TMDQU1

B-MA0

A-TMA13

A-MBA2

A-TMDQSUB

A-TMDQL5

VCC_1.5V_DDR

A-TMBA1

VCC_1.5V_DDR

B-TMDQL6

B-MDQL7

B-TMA10

B-MRESETB

C1214

0.1uF

R1205

1K

1%

A-MA6

B-MA2

B-TMA13

A-TMBA2

C1228

0.1uF

C1208

0.1uF

C1245

0.1uF

A-MRASB

C1210

0.1uF

A-MDQL5

B-MWEB

C1218

0.1uF

A-TMCKE

A-MDQL4

C1229

0.1uF

B-MDQL1

C1233

0.1uF

A-MDQL6

B-TMA11

B-TMDQSU

A-MA3

A-TMDQSL

A-TMDQSLB

R1226

2401%

A-MA7

B-MA8

A-TMDQL6

A-TMBA0

A-MDQSU

A-MA13

A-MDQSUB

B-MA1

C1250

0.1uF

A-TMA10

B-TMDQU1

B-TMWEB

B-MDQU3

B-TMRESETB

A-MA13

B-TMDML

B-MCKE

B-TMA0

A-MA8

A-MCKB

A-TMDQL3

A-TMA5

A-TMDQU4

A-MA7

B-TMDQSU

A-TMDQSUB

B-MDML

A-MBA2

B-TMDQU4

B-TMA5

A-MDQL2

B-TMDQU0

A-MVREFCA

C1204 1000pF

A-MBA0

C1215

0.1uF

A-MA8

B-MRESETB

B-TMDQSLB

B-TMDQSL

A-MRASB

B-TMA0

B-MBA1

A-TMDQU7

A-MA1

B-MDQU0

A-MDQU0

B-MRASB

B-TMA1

B-TMBA2

A-TMDQL2

A-TMDQU2

A-MRESETB

A-TMDQL2

A-MDQL0

A-TMDML

B-MDQL5

B-TMA8

B-MBA1

A-TMA13

B-MDQSL

B-MDQL3

A-MDQL7

A-TMDQSU

C1212

0.1uF

A-TMA5

A-TMDQU4

B-MDQL0

A-MWEB

B-TMA9

A-TMA0

B-MA10A-MA12

A-MCKE

B-TMDQSL

A-TMA4

B-TMDQSLB

B-MDQU4

R1225

1K

1%

B-TMDQL1

C12491000pF

B-MBA2

B-TMBA1

B-MDQU1

A-MA0

B-MA10

A-MVREFDQ

B-TMDQU7

B-MDQSUB

C1243

0.1uF

A-MDQU2

B-MA13

C1211

0.1uF

A-TMA1

A-MBA1

A-MCASB

B-TMDQL0

B-MDQSL

A-TMA8

B-TMDQL7A-MDQU3

A-MA5

B-MVREFDQ

B-MA1

B-MDML

B-MDQSU

B-MA6

B-MDMU

B-MCKB

A-MDMU

B-TMDQU5

A-TMDQL0

B-MCK

B-MCASB

A-TMDQU7

A-TMCASB

VCC_1.5V_DDR

A-MA4

VCC_1.5V_DDR

A-MDQU4

B-TMDMU

A-TMA6

A-TMA12

B-TMCK

R1201

1K1%

B-TMBA2

C1216

0.1uF

C1220

0.1uF

A-MDML

B-TMBA0

VCC_1.5V_DDR

A-MDMU

B-MDQL6

A-MDQU1

B-MBA0

B-TMDQU3

A-TMDQL4

A-MA10

B-TMRASB

B-MCKB

B-MA11

B-MDQU4

A-TMA11

A-TMWEB

A-TMDQU3

B-MA11

B-MBA2

B-TMCKE

B-MDQL5

B-TMDQSUB

A-TMA7

A-TMA9

B-TMA6

B-TMDQL5

B-MA6

A-TMA9

B-MA7

B-MA3

C1222

0.1uF

A-TMA1

A-TMA11

A-MA2

B-TMDQU5

C1217

0.1uF

A-MDQL5

A-TMBA0

C1213

0.1uF

C1207

0.1uF

A-TMDQU1

A-TMDQU5

A-TMDQU5

A-TMBA2

B-TMA2

A-TMA3

C1234

0.1uF

A-MA12

A-MDQU0

B-TMA2

B-MDQSLB

B-TMCKB

A-MDQSUB

A-MDQSL

B-TMDQL3

A-TMA7

A-MDQU7A-MDQU5

C1205

10uF

C122510uF10V

C1246

10uF

VCC_1.5V_DDR

R123110K

VCC_1.5V_DDR

R123210K

R1223

10

R1217

10

R1216

10

R1211

10

R1213

10

R1222

10

R1215

10

R1220

10

R1218

10

R1221

10

R1210

10

R1206

10

R1214

10

R1208

10

R1207

10

R1209

10

R1219

10

R1212

10

AR1218

10

AR1215

10

AR1208

10

AR1219

10

AR1216

10

AR1214

10

AR1211

10

AR1220

10

AR1201

10

AR1202

10

AR1217

10

AR1204

10

AR1207

10

AR1210

10

AR1213

10

AR1209

10

AR1203

10

AR1205

10

AR1212

10

AR1206

10

R123410KB-MCKE

A-MCKER1233 10K

H5TQ1G63BFR-H9CIC1202

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

A13T3

A15M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_6T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9

H5TQ1G63BFR-H9CIC1201

A0N3

A1P7

A2P3

A3N2

A4P8

A5P2

A6R8

A7R2

A8T8

A9R3

A10/APL7

A11R7

A12/BCN7

A13T3

A15M7

BA0M2

BA1N8

BA2M3

CKJ7

CKK7

CKEK9

CSL2

ODTK1

RASJ3

CASK3

WEL3

RESETT2

DQSLF3

DQSLG3

DQSUC7

DQSUB7

DMLE7

DMUD3

DQL0E3

DQL1F7

DQL2F2

DQL3F8

DQL4H3

DQL5H8

DQL6G2

DQL7H7

DQU0D7

DQU1C3

DQU2C8

DQU3C2

DQU4A7

DQU5A2

DQU6B8

DQU7A3

VREFCAM8

VREFDQH1

ZQL8

VDD_1B2

VDD_2D9

VDD_3G7

VDD_4K2

VDD_5K8

VDD_6N1

VDD_7N9

VDD_8R1

VDD_9R9

VDDQ_1A1

VDDQ_2A8

VDDQ_3C1

VDDQ_4C9

VDDQ_5D2

VDDQ_6E9

VDDQ_7F1

VDDQ_8H2

VDDQ_9H9

NC_1J1

NC_2J9

NC_3L1

NC_4L9

NC_6T7

VSS_1A9

VSS_2B3

VSS_3E1

VSS_4G8

VSS_5J2

VSS_6J8

VSS_7M1

VSS_8M9

VSS_9P1

VSS_10P9

VSS_11T1

VSS_12T9

VSSQ_1B1

VSSQ_2B9

VSSQ_3D1

VSSQ_4D8

VSSQ_5E2

VSSQ_6E8

VSSQ_7F9

VSSQ_8G1

VSSQ_9G9

R1235

56 1%

R1236

56 1%

C1209

0.01uF25V

R1237

56

1%

R1238

56

1%

C1240

0.01uF25V

LGE107D (S7M Divx_Non RM)IC101

S7M_DIVX & MS10

A_DDR3_A0/DDR2_A13B8

A_DDR3_A1/DDR2_A8B9

A_DDR3_A2/DDR2_A9A8

A_DDR3_A3/DDR2_A1C21


A_DDR3_A5/DDR2_A10A22



A_DDR3_A8/DDR2_A6C9


A_DDR3_A10/DDR2_RASZB11




A_DDR3_BA0/DDR2_BA2B21

A_DDR3_BA1/DDR2_CASZA11

A_DDR3_BA2/DDR2_A5A23

A_DDR3_MCLK/DDR2_MCLKA12

A_DDR3_MCLKZ/DDR2_MCLKZC11

A_DDR3_CKE/DDR2_DQ5B12

A_DDR3_ODT/DDR2_ODTC20

A_DDR3_RASZ/DDR2_WEZA20

A_DDR3_CASZ/DDR2_BA1B20

A_DDR3_WEZ/DDR2_BA0A21

A_DDR3_RESETBC22

A_DDR3_DQSL/DDR2_DQS0C16

A_DDR3_DQSLB/DDR2_DQSB0B16

A_DDR3_DQSU/DDR2_DQSB1A16

A_DDR3_DQSUB/DDR2_DQS1C15

A_DDR3_DML//DDR2_DQ13A14

A_DDR3_DMU/DDR2_DQ6B18

A_DDR3_DQL0/DDR2_DQ3C18

A_DDR3_DQL1/DDR2_DQ7B13

A_DDR3_DQL2/DDR2_DQ1A19



A_DDR3_DQL5/DDR2_DQ0A13

A_DDR3_DQL6/DDR2_CKEB19


A_DDR3_DQU0/DDR2_DQ15A15


A_DDR3_DQU2/DDR2_DQ8B14

A_DDR3_DQU3/DDR2_DQ11C17

A_DDR3_DQU4/DDR2_DQM1B15


A_DDR3_DQU6/DDR2_DQM0C14

A_DDR3_DQU7/DDR2_DQ14B17

B_DDR3_A0/DDR2_A13A25

B_DDR3_A1/DDR2_A8B24


B_DDR3_A3/DDR2_A1P25

B_DDR3_A4/DDR2_A2C24

B_DDR3_A5/DDR2_A10P26


B_DDR3_A7/DDR2_A3R24


B_DDR3_A9/DDR2_A12T26

B_DDR3_A10/DDR2_RASZD24


B_DDR3_A12/DDR2_A0C25

B_DDR3_A13/DDR2_A7T25

B_DDR3_BA0/DDR2_BA2P24

B_DDR3_BA1/DDR2_CASZC26

B_DDR3_BA2/DDR2_A5R26

B_DDR3_MCLK/DDR2_MCLKD26

B_DDR3_MCLKZ/DDR2_MCLKZD25

B_DDR3_CKE/DDR2_DQ5E24

B_DDR3_ODT/DDR2_ODTN25

B_DDR3_RASZ/DDR2_WEZM26

B_DDR3_CASZ/DDR2_BA1N24

B_DDR3_WEZ/DDR2_BA0N26

B_DDR3_RESETBR25

B_DDR3_DQSL/DDR2_DQS0J25

B_DDR3_DQSLB/DDR2_DQSB0J24

B_DDR3_DQSU/DDR2_DQSB1H26

B_DDR3_DQSUB/DDR2_DQS1H25

B_DDR3_DML/DDR2_DQ13F26

B_DDR3_DMU/DDR2_DQ6L24

B_DDR3_DQL0/DDR2_DQ3L25

B_DDR3_DQL1/DDR2_DQ7F24

B_DDR3_DQL2/DDR2_DQ1L26

B_DDR3_DQL3/DDR2_DQ10F25

B_DDR3_DQL4/DDR2_DQ4M25

B_DDR3_DQL5/DDR2_DQ0E26

B_DDR3_DQL6/DDR2_CKEM24

B_DDR3_DQL7/DDR2_DQ2E25

B_DDR3_DQU0/DDR2_DQ15G26

B_DDR3_DQU1/DDR2_DQ9J26

B_DDR3_DQU2/DDR2_DQ8G24

B_DDR3_DQU3/DDR2_DQ11K25

B_DDR3_DQU4/DDR2_DQM1H24


B_DDR3_DQU6/DDR2_DQM0G25


DDR3(256MB)

GP2_Saturn7M

DDR3 1.5V By CAP - Place these Caps near MemoryDDR3 1.5V By CAP - Place these Caps near Memory

CLose to DDR3CLose to Saturn7M IC CLose to Saturn7M IC

Close to DDR Power PinClose to DDR Power Pin

CLose to DDR3

Ver. 1.0

21



SPI_SCK/FLASH_WP

R14020

R1401

0OPT

/SPI_CS

R1404

4.7K

C1401

0.1uF

+3.3V_Normal+3.3V_Normal

Q1401KRC103S

E

B

C

+3.3V_Normal

R1403

10K

R140533

SPI_SDO

SPI_SDI

IC1401MX25L8005M2I-15G

S_FLASH

3WP#

2SO

4GND

1CS#

5SI

6SCLK

7HOLD#

8VCC

S-Flash(1MB)


23



+5V_TU

TUNER_RESETC5006100pF50V

C50110.01uF25VBOOSTER_OPT

TU_CVBS

CONTROL_ATTEN

R5009100

+3.3V_TU

R50010

RF_AGC_OPT

C50030.1uF16V

+5V_TU

L5003

BLM18PG121SN1D

R50172.2K

BOOSTER_OPT

+3.3V_Normal

+3.3V_TU

Q50032SC3052

RF_AGC_OPTE

B

C

C50240.1uF16V

RF_SWITCH_CTL

C501822uF16VOPT

C50020.1uF16VRF_S/W_OPT

+1.2V/+1.8V_TU

LNA2_CTL

+5V_TU

IF_N_MSTAR

Q5005ISA1530AC1

NON_TU_CVBS_BYPASS

E

B

C

L5001

MLB-201209-0120P-N2BOOSTER_OPT

+3.3V_TU

+3.3V_TU

C50100.1uF16V

C50070.1uF16V

TU_SDA

R50271K

OPT

L5002

BLM18PG121SN1D

R5003 0

IF_AGC_SEL

C50210.1uF16V

R502110K

BOOSTER_OPT

R50254.7K

R50261K

OPT

R5011100K

C50220.1uF16V

R50020

RF_S/W_OPT

Q5001

ISA1530AC1BOOSTER_OPT

E

B

C

C5001100pF50V

+3.3V_TU

R50221K

C50160.1uF16V

OPT

C50260.1uF16VRF_AGC_OPT

C50230.1uF16V

R5014

0BOOSTER_OPT

R503282

+5V_TU

C501722uF16VOPT

TU_SIF

Q5004ISA1530AC1

E

B

C

C502022uF16V

C501922uF16V

IF_P_MSTAR

C502710uF10VRF_AGC_OPT

TU_SCL

+5V_TU

Q50022SC3052

BOOSTER_OPTE

B

C

R5024 0

R502810K

RF_AGC_OPT

R5019

10K

BOOSTER_OPT

+1.2V/+1.8V_TU

R50331

C50280.1uF16V

C502910uF10V

R5034 0NON_DEMOD_OPT

R5035 0NON_DEMOD_OPT

R50381.2K

R503610

R5007 100

DEMOD_OPT

R5006 100

DEMOD_OPT

IF_P_EXT

IF_N_EXT

C50310.1uF16V

IF_AGC

C5025

0.1uF 16V

R5029470

TU5001TDTJ-S001D

DVB_1INPUT_H_LGIT

143.3V

131.2V

5AS

12GND

11VIDEO

2BST_CNTL

10NC

4NC[RF_AGC]

1ANT_PWR[OPT]

17DIF_1

9SIF

8NC[IF_TP]

3+B

16IF_AGC_CNTL

7SDA

6SCL

15RESET

18DIF_2

19

SHIELD

IC5001

AZ1117H-ADJTRE1(EH11A)

2

OUTPUT

3INPUT 1 ADJ/GND

R5030220NON_TU_CVBS_BYPASS

R5031220

TU5001-*3

TDVJ-H001FNTSC_1INPUT_H_LGIT

143.3V

131.2V

5AS

12GND

11VIDEO

2BST_CNTL

10NC

4NC[RF_AGC]

1ANT_PWR[OPT]

17DIF_1

9SIF

8NC(IF_TP)

3+B

16IF_AGC_CNTL

7SDA

6SCL

15RESET

18DIF_2

19

SHIELD

TU5001-*2TDVJ-H031FNTSC_1INPUT_V_LGIT

143.3V

131.2V

5AS

12GND

11VIDEO

2BST_CNTL

10NC

4NC[RF_AGC]

1ANT_PWR[OPT]

17DIF_1

9SIF

8NC(IF_TP)

3+B

16IF_AGC_CNTL

7SDA

6SCL

15RESET

18DIF_2

19

SHIELD

TU5001-*1TDTR-T035FNTSC_2INPUT_H_LGIT

14+B3[3.3V]

13+B2[1.2V]

5NC_2

12GND

11VIDEO

2BST_CTL

10NC_4

4NC_1[RF_AGC]

1RF_S/W_CTL

17DIF_1[N]

9SIF

8NC_3

3+B1[5V]

16IF/AGC

7SDAT

6SCLT

15RESET

18DIF_2[P]

19

SHIELD

R50390

TU_CVBS_BYPASS

R50181.2K

NON_BR_TU_I2C

R50201.2K

NON_BR_TU_I2C

R5015

NON_BR_TU_I2C

33

R5016

NON_BR_TU_I2C

33

C501218pF50V

NON_BR_TU_I2C

C501318pF50V

NON_BR_TU_I2C

C5012-*147pF50V

BR_TU_I2C

R5016-*1100

1/16W5%

BR_TU_I2C

R5020-*13.3K

BR_TU_I2C

R5015-*1100

1/16W5%

BR_TU_I2C

C5013-*147pF50V

BR_TU_I2C

R5018-*13.3K

BR_TU_I2C

TU5001-*4

UDA45AL

NTSC_1INPUT_H_SANYO

143.3V

131.2V

5AS

12GND

11VIDEO

2BST_CNTL

10NC

4NC[RF_AGC]

1ANT_PWR[OPT]

17DIF_1

9SIF

8NC(IF_TP)

3+B

16IF_AGC_CNTL

7SDA

6SCL

15RESET

18DIF_2

19

SHIELD

+5V_General

Ver. 1.1

GPIO must be added.

ATSC_CAN TUNER

The pull-up/down of LNA2_CTL is depended on MODLE_OPT_1.GPIO must be added for FE_BOOSTER_CTL

GP2_Saturn7M

Close to the tuner

OPTION : RF AGC

OPTION : BOOSTER

Pull-up can’t be applied because of MODEL_OPT_2

200mA

should be guarded by ground

OPTION : RF S/W

LGIT CAN H/N TUNER for US&KOR&BRAZIL&TAIWAN&AUS

60mA

26

This was being applied to the only china demod,so this has to be deleted in both main and ISDB sheet.

*Change History.

1.De-reting

1) R5029,R5030,R5031 : 1005 Type ==> 1608 Type(w.s.Jeong_1019)

Ver 1.0 --> 1.1:Change of chip type, 091019, w.s.jeong

2) R5030,R5031 : 200/1608 Type ==> 220/2012 Type(w.s.Jeong_1116)

2.ADD of TUNER P/N (w.s.Jeong_1116)

Ver 1.1 --> 1.2:Change of chip type, Add of Tuner P/N for NTSC_1INPUT091116, w.s.jeong

Option name:BR_TU_I2CBRAZIL model use I2C Standard Mode



FE_TS_DATA[1]

FE_TS_DATA[6]

FE_TS_DATA[4]

FE_TS_DATA[7]

FE_TS_DATA[5]

FE_TS_DATA[0]

FE_TS_DATA[2]

FE_TS_DATA[3]

FE_TS_CLK

C29210.1uF16V

ISDB_DEMOD

TP2902ISDB_DEMOD

IF_N_EXT

R2913 22ISDB_DEMOD

TP2901ISDB_DEMOD

R2906 10KISDB_DEMOD

C29110.1uF

16V

ISDB_DEMOD

IF_P_EXT

FE_TS_DATA[0-7]

C29170.1uF16V

ISDB_DEMOD

R2915

2.2K

OPT

C2926 0.1uF

ISDB_DEMOD

C29240.1uF16V

ISDB_DEMOD

R2911 22ISDB_DEMOD

C2928 0.1uF

ISDB_DEMOD

C29100.1uF

ISDB_DEMOD

TP2907ISDB_DEMOD

C29200.1uF16V

ISDB_DEMOD

DEMOD_SCL

C2927 0.1uF

ISDB_DEMOD

TP2904ISDB_DEMOD

C29180.1uF16V

ISDB_DEMOD

DEMOD_RESETR2907 2.2KISDB_DEMOD

C29130.1uF16V

ISDB_DEMOD

C2905 0.1uF ISDB_DEMOD

R29091M

ISDB_OPTIF_AGC_ISDB

+3.3V_DE

TP2905ISDB_DEMOD

C2925 0.1uF

ISDB_DEMOD

R2912 22ISDB_DEMOD


FE_TS_VAL_ERR

FE_TS_DATA[0]



R2905 2.2KISDB_DEMOD

C29160.1uF16V

ISDB_DEMOD

C291915pF50V

ISDB_DEMOD

R2910 22ISDB_DEMOD

C29230.1uF16V

ISDB_DEMOD

C2903 0.1uFISDB_DEMOD

FE_TS_SYNC

+3.3V_DE

TP2903ISDB_DEMOD

R2914

2.2K

OPT

DEMOD_SDA

C29220.1uF16V

ISDB_DEMOD

C291515pF50V

ISDB_DEMOD

TP2906ISDB_DEMOD




+1.2V_DE

C29120.1uF16V

ISDB_DEMOD

C2901 0.1uF

ISDB_DEMOD

FE_TS_DATA[0]



C2914

0.1uF

16V

ISDB_DEMOD

R290310K 1%

ISDB_DEMOD

X290125MHz

ISDB_DEMOD

IC2901

MN884433

ISDB_DEMOD

1VSS_1

2AVDD_S

3AII_S

4AIQ_S

5AVSS_S

6VRT_S

7VRB_S

8TCPO_S

9VDDL_1

10MSCL_S

11MSDA_S

12VSS_2

13VSSH

14PSEL

15ZSEL

16VDDL_2

17ACKI

18TCPO_T

19IR_T

20VRT_T

21VRB_T

22AVDD_T

23AIN_T

24AIP_T

25AVSS_T

26

VSS_3

27

MSCL_T

28

MSDA_T

29

VDDH_1

30

GPO1

31

AGCI_T

32

AGCR_T

33

GPO0

34

VDDL_3

35

VSS_4

36

XO

37

XI

38

VDDH_2

39

GPI1

40

GPI0

41

TEST4

42

SHVPP

43

SHVDDH

44

NC_1

45

VSS_5

46

VDDL_4

47

TCK

48

TDI

49

NRST

50

TEST3

51 VSS_652 VDDL_553 TRST54 TMS55 CSEL056 CSEL157 TDO58 SYNCA59 ERRA60 SYNCB61 ERRB62 VSS_763 VDDL_664 SADR_T65 NC_266 SADR_S67 HDVDDL068 VSS_869 SDA70 SCL71 VDDH_372 SADR73 INTA74 INTB75 VSS_9

76

TEST1

77

TEST2

78

SCKA

79

GPI2

80

SDOA

81

PCKA

82

DENA

83

VDDH_4

84

VSS_10

85

HDVPP

86

RON

87

NC_3

88

HDVDDH

89

NC_4

90

HDVDDL1

91

VSS_11

92

VDDL_7

93

SCKB

94

TEST0

95

SDOB

96

PCKB

97

DENB

98

GPO2

99

VDDH_5

100

AGC_S

ISDB-T Demodulator


PANASONIC (ISDB-T)

(FE_TS_SERIAL)

MN884433

(FE_TS_SERIAL)

28

AMP_I2C HAVE PULL-UP



+3.3V_DE+3.3V_DE

IC3001SC4215ISTRT

ISDB_POWER

3VIN

2EN

4NC_2

1NC_1

5NC_3

6VO

7ADJ

8GND

R30010

ISDB_DEMOD

L3001

BLM18PG121SN1D

ISDB_POWER

C3002

0.1uF

ISDB_POWER

R3003

10K

ISDB_POWER

C3001

0.1uF

ISDB_POWER

IF_AGC_SEL

C30050.1uF16V

ISDB_POWER

R3004

5.1K

ISDB_POWER

C30030.1uF16V

ISDB_POWER

TP3002

+1.2V_DE

C300622uF16V

ISDB_POWER

+3.3V_Normal

IF_AGC_MAIN

IF_AGC

R30020

MSTAR DEMOD

C300410uF10V

ISDB_POWER

IF_AGC_ISDB

Demodulator


IF AGC SELECTION

Panasonic Demodulator Power(3.3V,1.2V)

29



PCM_D[2]

PCM_D[6]

FE_TS_DATA[5]

FE_TS_DATA[7]

FE_TS_DATA[3]

PCM_D[1]

FE_TS_DATA[0]

FE_TS_DATA[6]

FE_TS_DATA[4]

PCM_D[3]

PCM_D[7]

FE_TS_DATA[1]

PCM_D[5]

PCM_D[4]

PCM_D[0]

FE_TS_DATA[2]

PCM_A[13]

/PCM_IORD

CI_TS_DATA[7]

CI_TS_CLK

CI_TS_SYNC

PCM_A[14]

/PCM_REG

CI_TS_DATA[5]

PCM_A[12]

/PCM_CD

PCM_A[10]

CI_TS_DATA[3]

FE_TS_VAL_ERR

PCM_A[8]

/PCM_WE

PCM_A[3]CI_TS_DATA[4]

CI_TS_DATA[1]

CI_TS_DATA[0]

/PCM_IOWR

PCM_A[0]

PCM_A[4]

FE_TS_CLK

PCM_5V_CTL

PCM_RST

PCM_A[11]

PCM_A[6]

PCM_A[9]

FE_TS_SYNC

PCM_A[2]

PCM_A[5]

/PCM_IRQA

/PCM_WAIT

CI_TS_VAL

/PCM_CE

FE_TS_DATA[0-7]

CI_TS_DATA[2]PCM_A[1]

PCM_A[7]

/PCM_OE

CI_TS_DATA[6]

PCM_D[0-7]

PCMCI

NON CI Region


46



TP2502

TP2501

TP2504 RF_ENABLE

RF_RESET

M_REMOTE_TX

M_REMOTE_RX

TP2503

NON Motion Remocon Region

GP2_Saturn7M

NON M REMOCON

Ver. 1.0

50



AMP_MUTE_HOTEL

SPK_R-_HOTEL

SPK_R+_HOTEL

NON CHINA HOTEL

NON CHINA HOTEL


52



R2626 0

S7_RXD1S7_RXD

S7_TXD1

WIRELESS_DL_RX

WIRELESS_PWR_EN

WIRELESS_SW_CTRL

S7_TXD

WIRELESS_DL_TX

WIRELESS_DETECT

R2627 0

NON-WIRELESS MODEL

GP2_Saturn7M

NON WIRELESS READY

Ver. 1.0

54



C7316 0.047uF

C7324 0.047uF

VDD33

L7308BLM18PG121SN1D

+1.5V_DDR

DDC_SDA_1

SIDEAV_L_IN

C7400

0.1uF

C7367

0.1uF

C7405

0.1uF

C7408

0.1uF

C735210uF

LNA2_CTL

DDC_SCL_2

D2-_HDMI1

R7344 33

SCART1_Lout

R7302 100

DSUB_B-

C7315 0.047uF

COMP2_R_IN

C7391

0.1uF

C7333 2.2uF

AVDD_DDR0

SC1_R-/COMP1_Pr-

VDD33_DVI

L7300BLM18PG121SN1D

R7318 33

TU_SDA

IF_AGC_SEL

D1-_HDMI1

R7334 33

DEMOD_SDA

SC1_B-/COMP1_Pb-

R7326 33

R7342 33

+3.3V_Normal

SC1/COMP1_L_IN

COMP2_Y-

IF_P_MSTARR7362 100

C7410

0.1uF

TU_CVBS

AVDD_DDR0

+3.3V_Normal

COMP2_Pb-

R7339 68

COMP2_L_IN

C7357

1000pF

OPT

MODEL_OPT_0

R7319 68

+1.26V_VDDC

MVREF

L7311BLM18PG121SN1D

AMP_SDA

C7319 0.047uF

MODEL_OPT_1

R7324 33

R7375

1K

1/16W

1%

AUD_SCK

L7303BLM18SG700TN1D

HPD1

X730024MHz

C7372

0.1uF

C7388

0.1uF

C7382

0.1uF

R7320 33

C7301 0.047uF

PC_R_IN

C7322 0.047uF

SC1_B+/COMP1_Pb+C7312 0.047uF

C7330 0.047uF

AU25

COMP2_Y+

R7316 33

AVDD2P5

AVDD25_PGA

AVDD_DDR0

R7343 68

R7340 33

DDC_SCL_1

DSUB_B+

R7331 33

R7314 22

HP_LOUT

ADC2P5

AVDD_DMPLL

D0-_HDMI2

MODEL_OPT_5

C7337 2.2uF

SIDE_USB_DM

DEMOD_SCL

R7305

10K

C7341 2.2uF

C7389

0.1uF

C7302 0.047uF

AVDD_DDR0

C7335 2.2uF

SOC_RESET

+3.3V_Normal

AVDD_DMPLL

C7378

0.1uF

C7394

0.1uF

MVREF

C7390

0.1uF

C7308 0.047uF

C74110.1uF

R7323 0

NON_EU

D1+_HDMI1

COMP2_Pr-

C7399

0.1uF

AV_L_IN

+3.3V_Normal

C73001000pF

OPT

SC1_CVBS_IN

R7325 68

L7305BLM18PG121SN1D

R73740

1/10W

5%

R7300 100

DSUB_VSYNC

AVDD_DMPLL

C7304 0.047uF

AVDD25_PGA

C7327 0.047uF

DSUB_HSYNC

AVDD_DDR1

D0-_HDMI1

C7342 2.2uF

DSUB_G-

C7334 2.2uF

C7307 1000pF

COMP2_Pr+

C73930.1uF

C7354 0.1uF

AVDD2P5

R7336 33

L7306

BLM18PG121SN1D

R737010K

C7377

0.1uF

C7376

0.1uF

C7323 0.047uF

AVDD2P5

C7340 2.2uF

C73461uF

CK+_HDMI1

SC1_G-/COMP1_Y-

R7361 100

R73661K

C7318 0.047uF

VDDC

090:AI26

RF_SWITCH_CTL

C7385

0.1uF

PC_L_INC7305 0.047uF

TP7304

R7303 100

AU33

+2.5V_Normal

CK-_HDMI1

+2.5V_Normal

D2+_HDMI1

D0+_HDMI2

C7310 0.047uF

C7384

0.1uF

R7341 68

C7326 0.047uF

+2.5V_Normal

MODEL_OPT_3

SC1_FB

C7309 0.047uF

COMP2_Pb+

SIDEAV_CVBS_IN

C7344 2.2uF OPT

AMP_SCL

C7387

0.1uF

C7314 1000pF

AU33

R7364 47

C7368

0.1uF

R7332 33

CK-_HDMI2

SPDIF_OUT

R7363

10K

C7396

0.1uF

R7304

10K

SC1_ID

VDDC

R7301 100

SC1_SOG_IN

L7310BLM18PG121SN1D

D2-_HDMI2

R7345 68

C7303 0.047uF

C7329 0.047uF

DTV/MNT_VOUT

C7374

0.1uF

C7404

0.1uF

COMP2_DET

TU_SIF

C7328 0.047uF

CK+_HDMI2

C7325 0.047uF

TU_SCL

TP7306

C7409

0.1uF

R7321 68

AUD_LRCH

VDD33

MIU1VDDC

D2+_HDMI2

+1.26V_VDDC

ADC2P5

AUD_LRCK

C7386

0.1uF

R7330 0

R7376

1K

1/16W

1%

AV_R_IN

D1+_HDMI2

C7313 0.047uF

C7380

0.1uF

DSUB_R-

R7349

1M

SC1_G+/COMP1_Y+

DSUB_G+

R7353 100

D0+_HDMI1

C73470.1uF

R7329 68

C7311 0.047uF

C7403

0.1uF

C7332 2.2uF

OPT

R73730

1/10W5%

L7309BLM18PG121SN1D

HPD2

C7406

0.1uF

C7331 2.2uFOPT

IR

C73590.022uF16V

IF_AGC_MAIN

C7353 0.1uF

AUD_MASTER_CLK

C7379

0.1uF

C7336 2.2uF

R7333 33

TP7305

VDD33_DVI

R7328 33

R7365 47

SCART1_Rout

R7354 100OPT

C73550.1uF

IF_N_MSTAR

C7392

0.1uF

R7335 33

DSUB_R+

HP_ROUT

AVDD_DDR1

R7338 33

R7322 0

C7339 2.2uF

C7321 1000pF

C7306 0.047uF

C7349 0.1uF

AVDD2P5

SIDEAV_R_IN

C7343 2.2uF OPT

C7320 0.047uF

SIDE_USB_DP

MODEL_OPT_2

C7338 2.2uF

SC1_R+/COMP1_Pr+

TP7301

R7337 33

R7315 22

L7307BLM18PG121SN1D

R7327 68

AV_CVBS_IN

DDC_SDA_2

C7348 0.1uF

C7317 0.047uF

R7317 68

TP7302

AU25

C7365

0.1uF

C7383

0.1uF

L7304BLM18PG121SN1D

TP7303

D1-_HDMI2

C73950.1uF

VDD33

SC1/COMP1_R_IN

L7301BLM18SG121TN1D

L7312BLM18SG121TN1D

TP7307

TP7308

TP7309

TP7300

D1-_HDMI4

D2+_HDMI4

HPD4

DDC_SCL_4

D0+_HDMI4

D0-_HDMI4

DDC_SDA_4

D2-_HDMI4

CK+_HDMI4

D1+_HDMI4

CK-_HDMI4

10uF

C7362

10uF

C7363

C7366

10uF

C7369

10uF

10uF

C7370

C737110uF

C737310uF

10uF

C7375

10uF

C7381

C7397

10uF

C7401

10uF

C736410uF

C73454.7uF

C7412 1uF

C7398

0.1uF

C7402

0.1uF

C7407

0.1uF

MIU1VDDC

VDD33

NEC_SCL

NEC_SDA

R7355 0 OPT

R7352 0 OPT

AMP_SCL

AMP_SDA

R7350 0

R7351 0

R7360 22DEMOD_OPT

R7359 22DEMOD_OPT

AV_CVBS_IN2

AV_CVBS_IN2TP211

R7313

1K

R7311

1K

R7312

1K

OPT

R7309

1K

R7310

1K

OPT

R7307

1K

HD

R7306

1K

FHD

R7308

1K

OPT

CEC_REMOTE_S7

L7313BLM18SG700TN1D

MIU0VDDC

MIU0VDDC

R7377

1K

OPT

R7378

1K

R7379

1K

OPT

R7380

1K

OPT

MODEL_OPT_5

MODEL_OPT_4

MODEL_OPT_4

VDD33

L7314BLM18PG121SN1D

C74130.1uF

C74140.1uF

AVDD_LPLL

AVDD_LPLL

10uF

C7361

C7415

0.1uF

L7302BLM18SG700TN1D

+1.26V_VDDC

C741610uF

C7350 27pF

C7351 27pF

L7315CM2012F5R6KT

5.6uH

L7316

CM2012F5R6KT5.6uH C7417

4.7uF10V

C74184.7uF10V

C74190.1uF

C7420

0.1uF

R7834

1K

OPT

R7833

1K

MODEL_OPT_6


S7M_DIVX & MS10A_RXCPF1

A_RXCNF2

A_RX0PG2

A_RX0NG3

A_RX1PH3

A_RX1NG1

A_RX2PH1

A_RX2NH2

DDCDA_DA/GPIO24F5

DDCDA_CK/GPIO23F4

HOTPLUGA/GPIO19E6

B_RXCPD3

B_RXCNC1

B_RX0PD1

B_RX0ND2

B_RX1PE2

B_RX1NE3

B_RX2PF3

B_RX2NE1

DDCDB_DA/GPIO26D4

DDCDB_CK/GPIO25E4

HOTPLUGB/GPIO20D5

C_RXCPAA2

C_RXCNAA1

C_RX0PAB1

C_RX0NAA3

C_RX1PAB3

C_RX1NAB2

C_RX2PAC2

C_RX2NAC1

DDCDC_DA/GPIO28AB4

DDCDC_CK/GPIO27AA4

HOTPLUGC/GPIO21AC3

D_RXCPA2

D_RXCNA3

D_RX0PB3

D_RX0NA1

D_RX1PB1

D_RX1NB2

D_RX2PC2

D_RX2NC3

DDCDD_DA/GPIO30B4

DDCDD_CK/GPIO29C4

HOTPLUGD/GPIO22E5

CEC/GPIO5D6

HSYNC0G5

VSYNC0G6

RIN0PK1

RIN0ML3

GIN0PK3

GIN0MK2

BIN0PJ3

BIN0MJ2

SOGIN0J1

HSYNC1G4

VSYNC1H6

RIN1PK5

RIN1MK4

GIN1PJ4

GIN1MK6

BIN1PH4

BIN1MJ6

SOGIN1J5

HSYNC2H5

RIN2PN3

RIN2MN2

GIN2PM2

GIN2MM1

BIN2PL2

BIN2ML1

SOGIN2M3

CVBS0PN4

CVBS1PN6

CVBS2PL4

CVBS3PL5

CVBS4PL6

CVBS5PM4

CVBS6PM5

CVBS7PK7

CVBS_OUT1M6

CVBS_OUT2M7

VCOM0N5

VIFPW2

VIFMW1

IPV2

IMV1

SSIF/SIFPY2

SSIF/SIFMY1

QPU3

QMV3

IFAGCY5

RF_TAGCY4

TGPIO0/UPGAINU1

TGPIO1/DNGAINU2

TGPIO2/I2C_CLKR3

TGPIO3/I2C_SDAT3

XTALINT2

XTALOUTT1

SPDIF_IN/GPIO177G14

SPDIF_OUT/GPIO178G13

DM_P0B7

DP_P0A7

DM_P1AF17

DP_P1AE17

I2S_IN_BCK/GPIO175F14

I2S_IN_SD/GPIO176F13

I2S_IN_WS/GPIO174F15

I2S_OUT_BCK/GPIO181D20

I2S_OUT_MCK/GPIO179E20

I2S_OUT_SD/GPIO182D19

I2S_OUT_SD1/GPIO183F18

I2S_OUT_SD2/GPIO184E18

I2S_OUT_SD3/GPIO185D18

I2S_OUT_WS/GPIO180E19

LINE_IN_0LN1

LINE_IN_0RP3

LINE_IN_1LP1

LINE_IN_1RP2

LINE_IN_2LP4

LINE_IN_2RP5

LINE_IN_3LR6

LINE_IN_3RT6

LINE_IN_4LU5

LINE_IN_4RV5

LINE_IN_5LU6

LINE_IN_5RV6

LINE_OUT_0LU4

LINE_OUT_2LW3

LINE_OUT_3LW4

LINE_OUT_0RV4

LINE_OUT_2RY3

LINE_OUT_3RW5

MIC_DET_INR4

MICCMT5

MICINR5

AUCOMT4

VRMP7

VAGR7

VRPP6

HP_OUT_1LR1

HP_OUT_1RR2

ET_RXD0E21

ET_TXD0E22

ET_RXD1D21

ET_TXD1F21

ET_REFCLKE23

ET_TX_END22

ET_MDCF22

ET_MDIOD23

ET_CRSF23

AVLINKF8

IRINTG8

TESTPINK8

RESETA4

U3_RESETY17


S7M_DIVX & MS10VDDC_1

H11

VDDC_2H12

VDDC_3H13

VDDC_4H14

VDDC_5H15

VDDC_6J12

VDDC_7J13

VDDC_8J14

VDDC_9J15

VDDC_10J16

VDDC_11L18

A_DVDDH16

B_DVDDK19

FRC_VDDC_0L19

FRC_VDDC_1M18

FRC_VDDC_2M19

FRC_VDDC_3N18

FRC_VDDC_4N19

FRC_VDDC_5N20

FRC_VDDC_6P18

FRC_VDDC_7P19

FRC_VDDC_8P20

U3_DVDD_DDRY12

AVDD1P2J11

DVDD_NODIEL7

AVDD2P5_ADC_1H7

AVDD2P5_ADC_2J7

AVDD25_REFJ8

AVDD_AU25L8

PVDD_1W15

PVDD_2Y15

AVDD25_PGAU8

AVDD_NODIEM8

AVDD_DVI_1N9

AVDD_DVI_2P9

AVDD3P3_CVBSN8

AVDD_DMPLLP8

AVDD_AU33T7

AVDD_EAR33U7

AVDD33_TT9

VDDP_1R8

VDDP_2R9

VDDP_3T8

FRC_VD33_2_1V20

FRC_VD33_2_2W20

FRC_AVDD_RSDS_1U19

FRC_AVDD_RSDS_2U20

FRC_AVDD_RSDS_3V19

FRC_AVDDW19

FRC_AVDD_LPLLU18

FRC_AVDD_MPLLT20

FRC_VDD33_DDRY14

AVDD_MEMPLLR19

FRC_AVDD_MEMPLLW14

AVDD_DDR0_D_1D15

AVDD_DDR0_D_2D16

AVDD_DDR0_D_3E15

AVDD_DDR0_D_4E16

AVDD_DDR0_CE17

AVDD_DDR1_D_1F16

AVDD_DDR1_D_2F17

AVDD_DDR1_D_3G16

AVDD_DDR1_D_4G17

AVDD_DDR1_CH17

FRC_AVDD_DDR_D_1AB11

FRC_AVDD_DDR_D_2AB12

FRC_AVDD_DDR_D_3AC11

FRC_AVDD_DDR_D_4AC12

FRC_AVDD_DDR_CAA12

MVREFG15

NC_1Y7

NC_2Y8

GND_1G18

GND_2H9

GND_3H10

GND_4H18

GND_5H19

GND_6J10

GND_7J17

GND_8J18

GND_9J19

GND_10K9

GND_11K10

GND_12K11

GND_13K12

GND_14K13

GND_15K14

GND_16K15

GND_17K16

GND_18K17

GND_19K18

GND_20L9

GND_21L10

GND_22L11

GND_23L12

GND_24L13

GND_25L14

GND_26L15

GND_27L16

GND_28L17

GND_29M9

GND_30M10

GND_31M11

GND_32M12

GND_33M13

GND_34M14

GND_35M15

GND_36M16

GND_37M17

GND_38N10

GND_39N11

GND_40N12

GND_41N13

GND_42N14

GND_43N15

GND_44N16

GND_45N17

GND_46P10

GND_47P11

GND_48P12

GND_49P13

GND_50P14

GND_51P15

GND_52P16

GND_53P17

GND_54R10

GND_55R11

GND_56R12

GND_57R13

GND_58R14

GND_59R15

GND_60R16

GND_61R17

GND_62R18

GND_63T10

GND_64T11

GND_65T12

GND_66T13

GND_67T14

GND_68T15

GND_69T16

GND_70T17

GND_71T18

GND_72T19

GND_73U10

GND_74U11

GND_75U12

GND_76U13

GND_77U14

GND_78U15

GND_79U16

GND_80U17

GND_81V7

GND_82V8

GND_83V9

GND_84V10

GND_85V11

GND_86V12

GND_87V13

GND_88V14

GND_89V15

GND_90V16

GND_91V17

GND_92V18

GND_93W7

GND_94W8

GND_95W9

GND_96W10

GND_97W11

GND_98W12

GND_99W13

GND_100W16

GND_101W17

GND_102W18

GND_103Y13

GND_104Y18

GND_105AA13

GND_106AB13

GND_107AC13

GND_FUJ9

PGA_VCOMU9

GND_108D17

GND_109H23

GND_110AF13

GP2_Saturn7M

MAIN_2

ANALOG SIF

I2S_I/F

DSUB

Normal 2.5V

Close to MSTAR

MODEL OPTION

Normal Power 3.3VDTV_IF

AVDD_DMPLL/AVDD_NODIE:7.362mA

AU25:10mA

Close to MSTAR

AVDD_MEMPLL:24mA

VDD33_DVI:163mA

SCART1_RGB/COMP1

AVDD2P5/ADC2P5:162mA

AVDD25_PGA:13mA

VDDC : 2026mA

AVDD_DDR0:55mA

H/P OUT

VDDC 1.26V

CVBS In/OUT

AUDIO OUT

TU/DEMOD_I2C

AUDIO IN

COMP2

Close to MSTAR

SIDE USB

DDR3 1.5V

VDD33_T/VDDP/U3_VD33_2:47mA

HDMI

AU33:31mA

Close to MSTAR

RSDS Power OPT

AVDD_DDR1:55mA

Ver. 1.4

90

090916 modified

090916 modified

LCD

MODEL_OPT_3

PIN NAME

B6

F9

FHD

HIGH

FRCG19

LOW

OLED

E18

MODEL_OPT_2

MODEL_OPT_4

GIP

MODEL_OPT_0

F7

MODEL OPTION

NO FRC

50/60Hz LVDS100/120Hz LVDS

DDR_256MB

D18

MINI LVDSC5

MODEL_OPT_5

MODEL_OPT_1

HD

NON_GIP

DDR_512MB

MODEL_OPT_6

PIN NO.

LVDS



RXA4+

RXB4+

RXA0-

RXACK+

RXA0+

RXB0+

RXB1+

RXBCK-

RXB2-

RXA3-

RXA1+

RXB1-

RXB4-

RXB3+

RXBCK+

RXB2+

RXA2-

RXB0-

RXA4-

RXA2+

RXA1-

RXA3+

RXB3-

RXACK-


S7M_DIVX & MS10
















































FRC_REXTY11

FRC_TESTPINY19



A0P/RLV0P/RED[9]U26

A0M/RLV0N/RED[8]U25

A1P/RLV1P/RED[7]U24

A1M/RLV1N/RED[6]V26

A2P/RLV2P/RED[5]V25

A2M/RLV2N/RED[4]V24

A3P/RLV4P/RED[1]W24

A3M/RLV4N/RED[0]Y26















CCKP/LLV3PAD23

CCKM/LLV3NAE23







C3P/LLV4PAF23

C3M/LLV4NAD22

C4P/LLV5PAE22

C4M/LLV5NAF22

DCKP/TCON5AD19

DCKM/TCON4AE19

D0P/LLV6PAD21

D0M/LLV6NAE21

D1P/LLV7PAF21

D1M/LLV7NAD20

D2P/LLV8PAE20

D2M/LLV8NAF20

D3P/TCON3AF19

D3M/TCON2AD18

D4P/TCON1AE18

D4M/TCON0AF18






FRC_GPIO1AA14

FRC_GPIO3AC15

FRC_GPIO8Y16


FRC_GPIO10AC14

FRC_I2CM_DAAA16

FRC_I2CM_CKAA15

FRC_I2CS_DAY10

FRC_I2CS_CKAA11

FRC_PWM0AB15

FRC_PWM1AB14

DDR3(FRC)


92


THERMAL


+12V/+15V +24V/+15V

R752210K

OPT

R751010K

L7512

R7563

4.7K

1%R7558

10K

+2.5V_Normal

R7548

5.1K

5%

Adapter

R7532

0

POWER_ON/OFF2_2

POWER_ON/OFF2_2

R752110K

POWER_ON/OFF2_1

C75530.1uF16V

PANEL_VCC

C7528

100pF

50V

R7567

10K

1%

R7512

33K

1%

C75470.1uF16V

R7533

22K 1%

L75133.6uH

NR8040T3R6N

AMP_VCC

R7536

24K 1%

Q75032SC3052

E

B

C

C752910uF16VOPT

R7552

1

R7513

6.2K

1%

+12V/+15V

+12V/+15V

Q75052SC3052

E

B

C

R755912K

C75700.1uF16V

R7562

27K

1%

C754622uF10V

C7530

1uF10V

L7511

+3.5V_ST

Q7500

E

B

C

+12V/+15V

L7500

R7565

51K

5%

L75143.6uH

NR8040T3R6N

C75250.01uF25V

POWER_DET

R752722K

R7566

1.5K

1%

IC7506AOZ1073AIL

3AGND

2VIN

4FB

1PGND

5COMP

6EN

7LX_1

8LX_2

C7562100pF50V

OPT

C755010uF25V

C7560

2200pFC7565100pF50V

C752022uF10V

C75411uF25VOPT

+5V_Normal

C75160.1uF16V

+1.26V_VDDC

C754910uF25V

+3.3V_Normal

C7534

0.1uF

50V

0.1uFC7548

POWER_ON/OFF2_2

R7569

10K

OPT

R752475K1/8W1%

+3.5V_Normal

R750010KAdapter

C755610uF10V

C755110uF25V

L7507

PANEL_CTL

+5V_Normal

R7528

101/10W1%

+3.5V_ST

C7558

2200pF

+24V/+15V

R75579.1K

C755210uF25V

POWER_ON/OFF2_1

C75570.1uF16V

R750910K

R7547

30K

1%

Adapter

R7564

10K

1%

R752322K

L75103.6uH

NR8040T3R6N

IC7500MP8706EN-C247-LF-Z

3SW_2

2SW_1

4BST

1IN

5EN/SYNC

6FB

7VCC

8GND

R753910K

R756010K

C75314.7uF

16V

C756322uF10V

C756622uF10V

R7530-*122K

5V_PANEL

R7531-*1

2.7K

5V_PANEL

L7515CIC21J501NE

C75690.1uF16V

+3.5V_ST

+24V/+15V

OLP

R751710KOPT

+3.3V_Normal

+3.5V_ST

Q75022SC3052E

B

C

R751610K

INV_CTLR751510K

A_DIM

PWM_DIM

P7500

SMAW200-12

NON_Adapter

1+15V

2+15V

3GND

4GND

5+3.5V_ST

6+3.5V_ST

7GND

8OLP

9INV_ON

10P_DIM

11A_DIM

12NC

R7511

6.8K

OPT

L7504MLB-201209-0120P-N2 Adapter

+12V/+15V

C753210uF25V

AdapterC753710uF25V

Adapter

C75363.3uF50V

AdapterC75403.3uF50V

AdapterC75330.1uF50V

Adapter

+24V/+15V

C75450.1uF50V

Adapter

C75221uF50V

Adapter

R7561100K

L75093.6uH

NR8040T3R6N

Adapter

D7500

MBRA340T3G

Adapter

C75430.1uF50V

Adapter

+24V/+15V

C7527

0.1uF50V

Adapter

RL_ON

R7529100K

Adapter

+3.5V_STC75423.3uF50V

Adapter

C753810uF10V

Adapter

R7525

68K

1/16W

5%

Adapter

C7524220pF50V

AdapterR7537200K

1/8W1%

Adapter

C75440.1uF50V

Adapter

R7544105K

1/10W1%

Adapter

R7543

30K

1/10W

1%

Adapter

R7538

6.8K

1%

Adapter

R7542

22K

OPT

Q7504Si4800BDY

Adapter

3S3

2S2

4G

1S1

5D5

6D6

7D7

8D8

C75071uF6.3VOPT

R75054.7K

C75061uF6.3VOPT

C75050.01uF50V

C750010uF25V

C75180.1uF16V

C7510100pF50V

OPTC75081uF50V

L75013.6uH

NR8040T3R6N

IC7501MP2212DN

3IN

2GND

4BS

1FB

5VCC

6SW_1

7SW_2

8EN/SYNC

C75191uF25V

Adapter

C75090.1uF

16V

NON_Adapter

R750322K

C751322uF10V

C75110.1uF

16V

NON_Adapter

L7502MLB-201209-0120P-N2

NON_Adapter

C7512

100pF

50V

OPT

C75010.1uF50V

C75032.2uF50V

C75040.1uF

C751768uF35V

L7503MLB-201209-0120P-N2

NON_Adapter C75140.1uF

50V

OPC_OUTR75070

OPT

R75060

R75080

OPT

OPC_OUT

R7571

22

Adapter

C757110uF10V

Adapter

R75141K

R75720

NON_Adapter

+12V/+15V

R7570

18K

Adapter

L7505

5V_PANEL

+3.5V_Normal

R755510K

C75594.7uF

16V

Q75072SC3052

E

B

C

C75540.01uF

C75680.1uF16V

R754510K

POWER_ON/OFF2_2

+3.5V_ST

C75550.1uF

R755122K

C75611uF25V

C75260.1uF16V

R757810K

R7576

10

1%

C7573

100pF

50V

R7574

11K5%

L7506R7575

10K 1%

R7577 0

POWER_ON/OFF1

IC7504MP2212DN

3IN

2GND

4BS

1FB

5VCC

6SW_1

7SW_2

8EN/SYNC

C757622uF10V

C7575

0.1uF

50V

L7516

3.6uH

+1.5V_DDR

+3.5V_ST

C757222uF10V

C7574

1uF10V

0.1uFC7577

R7579

0Adapter_LGD

ERROR_OUT

R7580

0OPT

P7501

SM14B-SRSS-TB

Adapter

124V

224V

324V

424V

524V

6GND

7GND

8GND

9GND

10GND

11NC

12INV_ON

13PWM_DIM

14ERROR_OUT

15

GND

L7517

12V_PANEL

R7540120K

1%

Adapter

R7581

1.6K

1/8W

1%

Adapter

C75670.1uF16V

C75780.1uF16V

Q7506AO3407A

G

DS

Q7508AO3407A

G

DS

Q7501

AO3407A

G

D

S

IC7505

AZ2940D-2.5TRE1

2

GND

3 VOUT1VIN

C751568uF35VNON_Adapter

IC7507AOZ1072AI

3AGND

2VIN

4FB

1PGND

5COMP

6EN

7LX_1

8LX_2

R7582100

1%

+3.5V_STR7585100K LIPS

R7586100

1%

LIPS

R7548-*1

5.6K

1%

LIPS

R7547-*1

18K

1%

LIPS

R7583

1K

1/16W

1%

LIPS

R7584

27K

1/16W

1%

LIPS

C758068uF35V

C75020.1uF50V

IC7509-*1

G691L293T73UF

DEV_Repalcement

1

GND

2 RESET3VCC

+5V_USB

RL_ON

R783210K

NON_Adapter

C7913100pF50V

OPT

R785110K

+12V/+15V

R785022

C79190.1uF16V

C791010uF25V

R785210K

R7853

33K

1%

C79180.1uF16V

C79200.1uF

R7854

6.2K

1%

C791522uF10V

IC7511MP8706EN-C247-LF-Z

3SW_2

2SW_1

4BST

1IN

5EN/SYNC

6FB

7VCC

8GNDL

7910

L79113.6uH

NR8040T3R6N

C7914

100pF

50V

OPTC79211uF50V

POWER_ON/OFF2_2

+5V_General

JK7500

JPD003N-M432-4F

Adapter

GND

SW

24V

IC7503MP4460DQ-LF-Z

Adapter3

EN

2SW_2

4COMP

1SW_1

5FB

6GND

7FREQ

8VIN_1

9VIN_2

10BST

11

EP_GND

IC7502MP8670DN-LF-Z

Adapter

3VCC

2BST

4BG

1SW

5GND

6FB

7EN/SYNC

8IN

C79220.1uF50V

C79230.1uF50V

R75560

R753033K

12V_PANEL

R75315.6K12V_PANEL

L75084.7uH

SP-7850_4.7

Adapter

L7912MLB-201209-0120P-N2

Adapter

+24V_LED

+24V_LED_driver

Q7520Adapter

E

B

C

RL_ON

R786222KAdapter

+24V_LED_driver

C79240.1uF50VAdapter

C79252.2uF

Adapter50V

R786010K

Adapter

+24V_LED

Q7521Adapter

AO3407A

G

D

S

C79260.01uF50V

Adapter

R786127KAdapter

R750127K

C79270.1uF50V

C79280.01uF50V

IC7509

NCP803SN293

NCP

1

GND

3VCC 2 RESET

IC7510

NCP803SN293

NCP

1

GND

3VCC 2 RESET

IC7510-*1

G691L293T73UF

DEV_Repalcement

1

GND

2 RESET3VCC

C79330.01uF50V

C79323.3uF50V

R750222 1/10W

R7519

22

1/10W

5%

Adapter

L7913CPI2520NHL3R3ME

Adapter

L7914BLM18PG121SN1D

NON_Adapter1608

R7587

0

Adapter_AUO

R7549

0

Adapter_AUO

R7541 0

Adapter_LGD

POWER_SMALL

GP2_Saturn7 Ver. 1.00

Power_DET

R2

+5V_Normal

3A

+2.5V

3A

Placed on SMD-TOP

R1

Vout=0.8*(1+R1/R2)

+5V_USB

PANEL_POWER15V-->3.56V

C IN

Vd=550mV

3A

1934 mA

Vout=(1+R1/R2)*0.8

ST_3.5V-->3.5V --> 3.375V

R2

Placed on SMD-TOP

R1

New item

R1

300 mA

+15V Control

R1

24V-->3.48V

Vout=(1+R1/R2)*0.8

MAX 2000mA

R22026 mA

Close to IC

2A

Vout=0.8*(1+R1/R2)

Replaced Part

S7 core 1.26V volt

+3.3V_Normal

MAX 1A

R2

UNDER CHECKING

R1

R2

Placed on SMD-TOP

24V->15V

close to pin

24V->3.5V

$0.37

$0.12

$0.21

92

close to IC7502

Switching noise reducing [MPS recommend]

3.3K -> 1K (threshold voltage up)

4A -> 3A modify 090916

090916

090916

+3.5V_Normal

R1

C IN

Replaced Part

Placed on SMD-TOP

S7 DDR 1.5V

R2

Vout=0.8*(1+R1/R2)

Placed on SMD-TOP

Close to IC

3A

1074 mA

real output : 12.3V

Replacement Item

R13A

090916R2

MAX 300mATo Tuner

Vout=(1+R1/R2)*0.8

LED Driver Power

AO3407A Vgs : 10.8V

AO3407A Vgs : 10.8V

2A

AO3407A Vgs : 10.8V(24V input)

AO3407A Vgs : 8.3V(15V input)



Q76022SC3052

Commercial_EU EB

C

KEY2 D7605

5.6VCDS3C05HDMI1

R7619100

EYEQ/TOUCH_KEY

R761122

Commercial

+3.5V_ST

R761547K

Commercial

C76091000pF50VOPT

R761647K

Commercial

+3.5V_ST

C76060.1uF

16V

C76030.1uF

D76025.6V

AMOTECH

R761347K

Commercial_EU

R7601100

C7608100pF50V

C76051000pF50V

L7603BLM18PG121SN1D

C76020.1uF

LED_R/BUZZ

+3.3V_Normal

+3.5V_ST

C76071000pF50V

D7604

5.6VCDS3C05HDMI1

R7617100

C76110.1uF

16V

OPT

R7600100

LED_B/LG_LOGO

C76101000pF50VOPT

R761410K

Commercial_EU

+3.5V_ST

KEY1

L7604BLM18PG121SN1D

L7602BLM18PG121SN1D

R7618100

EYEQ/TOUCH_KEY

C76040.1uF

16V

R762210K

OPT

Q76032SC3052

Commercial

E

BC

D76065.6V

AMOTECH

L7605BLM18PG121SN1D

IR_OUT

D76035.6V

AMOTECH

R76120

Commercial_US

R760510K1%

R760610K1%

P7601

12507WR-12L

12PIN_ANGLE

1

2

3

4

5

6

7

8

9

10

11

12

13

R760447K

Q76002SC3052

EB

C

R760847K

R760710K

R760947K

R760222

+3.5V_ST

Q76012SC3052

E

BC

+3.5V_ST

IR+3.5V_ST

R76103.3KOPT

R76030

OPT

NEC_EEPROM_SCL

NEC_EEPROM_SDA

P7600

12507WR-03L

1

2

3

4

L7600BLM18PG121SN1D

L7601

BLM18PG121SN1D

C76000.1uF16V

C76010.1uF16V

D7601

5.6V

D7600

5.6V

P7601-*1

12507WS-12L

12PIN_STRAIGHT

1

2

3

4

5

6

7

8

9

10

11

12

13

R7621

1.5K

R7620 1.5K

CONTROL

IR & LED

IR & LED

Zener Diode is

GP2_Saturn7M

COMMERCIAL

Ver. 1.2

6

close to wafer



JP7704

R7727 0

DDC_SCL_1

IC7701

AT24C02BN-10SU-1.8

HDMI_2

3A2

2A1

4GND

1A0

5SDA

6SCL

7WP

8VCC

JP7706

R7738 0

Q77002SC3052

E

B

C

R7750 22

+3.5V_ST

R772910K

JP7703

R7716 0

R7732

3.3K

C7705

0.1uF

DDC_SDA_2

D2-_HDMI1

R7760

4.7K

R7748 22

R7730

1K

C77000.1uF16V

R7717 22

5V_DET_HDMI_1

R7757

10K

C7703

0.1uF

R7735 100

HDMI_CEC

R7708 100

D2-_HDMI2

R7702

1K

CK+_HDMI4

R7747 22

D2+_HDMI4

R7741 0

D1-_HDMI4

Q77022SC3052

E

B

C

DDC_SDA_1

D7701

R770722

CK-_HDMI1

R7754

4.7K

CEC_REMOTE_NEC

JK7700

EAG59023302

HDMI_2

14

13

5D1_GND

20

SHIELD

12

11

2D2_GND

19

18

10CK+

4D1+

1D2+

17

9D0-

8D0_GND

3D2-

16

7D0+

6D1-

15

D2+_HDMI2

D7704ENKMC2838-T112

A1

C

A2

DDC_SDA_4

R7734 22

JP7700

D0-_HDMI1

C77010.1uF16V

JP7701

R7723 0

DDC_SCL_2

R7718 22

D0-_HDMI4

DDC_SCL_1

JP7702

R7742 0

R7739 0

D1-_HDMI2

+5V_Normal

D0+_HDMI2

R7722 0

R7710 0

EDID_WP

R7719 100

JP7708

R7744

10K

R7752 22

D7703

R7761

4.7K

CK+_HDMI2

D7702

IC7702

AT24C02BN-10SU-1.8

HDMI_SIDE

3A2

2A1

4GND

1A0

5SDA

6SCL

7WP

8VCC

D1-_HDMI1

R7700

1K

HPD4R7728

10K

DDC_SDA_1

+5V_Normal

5V_HDMI_4

R7705

3.3K

5V_HDMI_4

R7726 0

D0+_HDMI4

+5V_Normal

R7725 0

R7733 22

R7709 0

R7755

10K

C77020.1uF16V

JP7705

R7736 0

D2-_HDMI4

HDMI_CEC

D1+_HDMI1

CK+_HDMI1

IC7700

AT24C02BN-10SU-1.8

HDMI_1

3A2

2A1

4GND

1A0

5SDA

6SCL

7WP

8VCC

R7749 22

CK-_HDMI4

D0+_HDMI1

D1+_HDMI4

D2+_HDMI1

R7759

4.7K

R7721 0

5V_DET_HDMI_4

JP7707

DDC_SDA_4

R7713 0

C7704

0.1uFR7743 0

R7737 0

D0-_HDMI2

R7703

1.8K

R7701

1.8K

R7731

1.8K

R7714 0

R7753

10K

R7758

4.7K

DDC_SCL_4

5V_HDMI_2

R776210K

CK-_HDMI2

JK7701

EAG59023302

HDMI_1

14

13

5D1_GND

20

SHIELD

12

11

2D2_GND

19

18

10CK+

4D1+

1D2+

17

9D0-

8D0_GND

3D2-

16

7D0+

6D1-

15

R7706 22

D7700

R7712 0

EDID_WP

5V_HDMI_2

R7720 0

HDMI_CEC

EDID_WP

D7705ENKMC2838-T112

A1

C

A2

HPD1

R7715 0

D7706ENKMC2838-T112

A1

C

A2

5V_HDMI_1

D1+_HDMI2

HPD2

HDMI_CEC

R7711 0

R7724 0

DDC_SCL_4

R7704

3.3K

C77060.1uF16V

5V_HDMI_1

5V_DET_HDMI_2

R7740 0

Q77012SC3052

E

B

C

DDC_SCL_2

R7756

4.7K

DDC_SDA_2

R7751 22

JK7702

EAG42463001

HDMI_SIDE

14

13

5D1_GND

20

JACK_GND

12

11

2D2_GND

19

18

10CK+

4D1+

1D2+

17

9D0-

8D0_GND

3D2-

16

7D0+

6D1-

15

D7707

AVRL161A1R1NT

OPT Q7703

BSS83

S B D

G

R77630

OPT

R7745

68K

R776468K

BSS83

Q7704

S B D

G

R776710K

D7708

R7765

68K

+3.3V_Normal

R776868KOPT

R77660

OPT

CEC_REMOTE_S7

D7709

AVRL161A1R1NT

OPT

C77070.1uF16V

R77690

CEC_ON/OFF

HDMI


94

$0.055

$0.253

For CEC

HDMI EEPROM

$0.055

$0.055

HDMI_1

HDMI_2

SIDE_HDMI

$0.253

$0.253



5V_DET_HDMI_3

FRC_RESET

SCAN_BLK1/OPC_OUT

SCAN_BLK2

TP7013

TP7014

TP7016

TP7017

WIRELESS_DL_TX

WIRELESS_DL_RXTP7018

TP7019

/PIF_SPI_CS

ET_RXER

/RST_PHY

WIRELESS_DETECT

WIRELESS_PWR_EN

TP7032

TP7033

RF_ENABLE

RF_RESET

TP7035

TP7036

TP7020

TP7021

TP7022

M_REMOTE_TX

M_REMOTE_RXTP7023

TP7024

FRC_SCLTP7025

FRC_SDATP7026

TP7027

UART_FRC_TXTP7028

UART_FRC_RX

FRC_PWM1

TP7029

TP7030

FRC_PWM0

TP7034 WIRELESS_SW_CTRL

MICOM BLOCKMAIN1 BLOCK

GP2_Saturn7 Ver. 1.0

TP_SMALL 75


THERMAL


C7834390pF50V

C782610uF35V

AMP_SDA

+1.8V_AMP

R7823

4.7K

AUD_LRCH

C78380.47uF50V

C781422pF50V

OPT

0.1uF

C7842

50V

C782922000pF

50V

R781612

R781712

L7804AD-8770

15uH

2S

1S 1F

2F

C7806

100pF50V

AUD_SCK

+1.8V_AMP

R78093.3

OPT

R7821

4.7K

R7831

3.3

OPT

AUD_MASTER_CLK

C782322000pF50V

D7802

100V1N4148W

OPT0.01uF

C7846

50V

OPT

R781512

C7835390pF50V

SPK_R-

C781322pF50V

OPT

0.1uFC7824

50V

+3.3V_Normal

C781922000pF

50V

R7802 100

SPK_L+

C78101000pF50V

0.1uF

C7843

50V

R78270

AMP_RESET_N

R781312

R7806

3.3K

+1.8V_AMP

C78030.1uF16V

R781812

R7828

3.3

OPT

R7803 100

0.1uFC7840

50V

R7822

4.7K

0.1uF

C7830

50V

C783310uF35V

C780210uF10V

C78251uF25V

0.1uFC7807

16V

0.01uFC7845

50V

OPT

0.01uFC7847

50V

OPT

D7801

100V1N4148W

OPT

L7801

BLM18PG121SN1D

C781722pF50V

OPT

0.1uFC7818

16V

0.01uFC7844

50V

OPT

AMP_MUTE_HOTEL

SPK_L-

+1.8V_AMP

R7829

3.3

OPTC78310.01uF50V

OPT

C780510uF10V

OPT

R78240

0.1uFC7841

50V

C78081000pF

50V

AMP_MUTE

0.1uFC7820

50V

C7828

22000pF50V

AMP_VCC

R7830

3.3

OPT

R781412

+3.3V_Normal

SPK_R+

C7836390pF50V

+3.5V_ST

R781212

C78221uF25V

AMP_VCC

C78000.1uF16V

AUD_LRCK

C78040.1uF16V

R781912

SPK_L+

AMP_SCL

R78070

OPT

D7803

100V1N4148W

OPT

L7802

BLM18PG121SN1D

C78271uF25V

Q78002SC3052

E

B

C

D7800

100V1N4148W

OPT

R7808 100

L7803AD-8770

15uH

2S

1S 1F

2F

0.1uF

C7832

50V

0.1uFC7811

L7800

BLM18PG121SN1D

TP7800

C78211000pF50V

C7837390pF50V

C7816

1uF 25V

R7811

10K

R7820

4.7K

R78260

POWER_DET

R7801 100

R781010K

C781510uF10V

OPT

SPK_L-

R78250

R7800

1

SPK_R-

C780110uF10V

OPT

SPK_R+

C78390.47uF50V

P7800

WAFER-ANGLE

1

2

3

4

IC7801

NTP-7000

EAN60969601

1BST1A

2VDR1A

3/RESET

4AD

5DGND_1

6GND_IO

7CLK_I

8VDD_IO

9DGND_PLL

10AGND_PLL

11LF

12AVDD_PLL

13DVDD_PLL

14GND

15

DGND_2

16

DVDD

17

SDATA

18

WCK

19

BCK

20

SDA

21

SCL

22

MONITOR0

23

MONITOR1

24

MONITOR2

25

/FAULT

26

VDR2B

27

BST2B

28

PGND2B_1

29 PGND2B_230 OUT2B_131 OUT2B_232 PVDD2B_133 PVDD2B_234 PVDD2A_135 PVDD2A_236 OUT2A_137 OUT2A_238 PGND2A_139 PGND2A_240 BST2A41 VDR2A42 NC

43

VDR1B

44

BST1B

45

PGND1B_1

46

PGND1B_2

47

OUT1B_1

48

OUT1B_2

49

PVDD1B_1

50

PVDD1B_2

51

PVDD1A_1

52

PVDD1A_2

53

OUT1A_1

54

OUT1A_2

55

PGND1A_1

56

PGND1A_2

57

EP_PAD

R7804 33

R7805 33

C780918pF50V

C781218pF50V

IC7800-*1KIA1117ST18

Replacement

2

OUT

3IN

1ADJ/GND

IC7800AP1117E18G-13

OUT

INADJ/GND

AUDIO[NTP]


96

2.5mm -> 2.0mm changed

SPEAKER_L

SPEAKER_R

120 mA



RXA0+

RXB0-

RXA2+

R7901 0EXCEPT_LGD_22

RXA1+

R791210K

LVDS_SEL_LOW

RXBCK+

RXB3-

RXB3+

RXB2+

RXA1-

R7900 0EXCEPT_LGD_22

C790010uF16VOPT

RXA3-

RXACK-

RXACK+

RXB1-

C79020.1uF16V

RXB0+

RXB1+

RXA3+

RXA2-

RXB4-

R791010K

BIT_SEL_LOW

RXBCK-

RXA0-

R7911

3.3KLVDS_SEL_HIGH

RXA4+

PANEL_VCC

P7900

TF05-51S

FHD

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

L7900120-ohm

FHD

RXA4-

+3.3V_Normal

C79011000pF50V

RXB4+

RXB2-

RXA1+R7914 0

HD_60Hz_NORMALL7901

120-ohm

HD_60Hz_NORMAL

SMALL_NC1

RXA2+

RXACK+

R7919

3.3KLVDS_SEL_HIGH

P7902

FF10001-30HD_60Hz_SMALL

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R7917 0OPT

R7915 0HD_60Hz_NORMAL

SMALL_NC3

+3.3V_NormalRXACK-

RXA0+

SMALL_NC2

P7901

FF10001-30HD_60Hz_NORMAL

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

RXACK+

OPC_EN

PANEL_VCC

SMALL_OPC_EN

RXA1-

RXA1-

RXA3-

RXA3+

OPC_OUT

RXA2-

SMALL_NC2

SMALL_NC4

RXA0-

PANEL_VCC

SMALL_NC4

RXA3+

RXA0-

RXA2-

SMALL_OPC_OUT

R7913 0OPT

SMALL_OPC_OUT

SMALL_NC1

RXACK-

RXA0+

L7902120-ohmHD_60Hz_SMALL

R792010KLVDS_SEL_LOW

PWM_DIMR7916 0OPT

SMALL_NC3

RXA2+ RXA3-

RXA1+

SMALL_OPC_ENC79030.1uF16V

HD_60Hz_NORMAL

C79041000pF50V

HD_60Hz_NORMAL

C790510uF16VOPT

C79060.1uF16V

HD_60Hz_SMALL

C79071000pF50V

HD_60Hz_SMALL

C790810uF16VOPT

L7904120-ohm

30PIN_FHD

RXA3+

RXA3-

RXA2-

RXA0-

C79090.1uF16V

30PIN_FHD

RXA1-

PANEL_VCC

C79111000pF50V30PIN_FHD

RXACK-

RXACK+

RXA0+

P7903

FF10001-3030PIN_FHD

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

RXA2+

C791210uF16VOPT

RXA1+

RXB0-

RXB2+

RXB3-

RXB0+

RXBCK+

RXB1+

RXB1-

RXB3+

RXB2-

RXBCK-

[51Pin LVDS Connector] (For FHD 60Hz)

[30Pin LVDS Connector] (For HD 60Hz_Small)

[30Pin LVDS Connector] (For HD 60Hz_Normal)

GP2_Saturn7M

LVDS 33

Ver. 1.0

must be located Bottom side

[30Pin LVDS Connector] (For HD 60Hz_Small)


THE SYMBOL MARK OF THIS SCHEMETIC DIAGRAM INCORPORATESSPECIAL FEATURES IMPORTANT FOR PROTECTION FROM X-RADIATION.FILRE AND ELECTRICAL SHOCK HAZARDS, WHEN SERVICING IF IS ESSENTIAL THAT ONLY MANUFATURES SPECFIED PARTS BE USED FORTHE CRITICAL COMPONENTS IN THE SYMBOL MARK OF THE SCHEMETIC. US_REAR_COMP_AV_SMALL

SIGN4269

SIGN4270

SIGN4272

SIGN4271

C9800100pF50VOPT

D98065.6V

R98060

D9802

30V

R98040

D98085.6V

D9800

5.6V

D98015.6V

R980010K

R9813470K

R980210K

R981710K

C980310pF50V

OPT

R9814470K

R9810470K

AV_CVBS_DET

R981610K

C98081000pF50V

D98055.6V

C980110pF50V

OPT

+3.3V_Normal

R981510K

R981810K

AV_CVBS_IN

D980430V

R981912K

+3.3V_Normal

R980775

AV_R_IN

R982112K

C98061000pF50V

D980330V

AV_L_IN

R982212K

COMP2_DET

R981275

C980210pF50V

OPT

C98041000pF50V

C98051000pF50V

R98011K

R982012K

R9811470K

D98075.6V

R980975

D980930V

R980875

R98031K

R98050

C980710pF50V

OPT

SCART1_MUTE

TP9809

TP9803

TP9801

TP9802

SC1_CVBS_IN

TP9808

SC_RE2

SCART1_Rout

SC1_SOG_IN

SC1_ID

TP9807

TP9804

TP9806

SC_RE1

DTV/MNT_VOUT

SCART1_Lout

SC1_FB

TP9805

JK9800

PPJ238-01

5D [GN2]O-SPRING

6D [GN2]E-LUG

4D [GN2]CONTACT

7E [BL2]E-LUG-S

5E [BL2]O-SPRING

7F [RD2]E-LUG-S

5F [RD2]O-SPRING_1

5G [WH2]O-SPRING

4H [RD2]CONTACT

5H [RD2]O-SPRING_2

6H [RD2]E-LUG

6A [YL1]E-LUG

5A [YL1]O-SPRING

4A [YL1]CONTACT

5B [WH1]O-SPRING

4C [RD1]CONTACT

5C [RD1]O-SPRING

6C [RD1]E-LUG

SC1_G-/COMP1_Y-

SC1_G+/COMP1_Y+

SC1_R+/COMP1_Pr+

SC1_B-/COMP1_Pb-

SC1_R-/COMP1_Pr-

SC1_B+/COMP1_Pb+

SC1/COMP1_L_IN

SC1/COMP1_R_IN

TP9810

TP9811

TP9812

TP9813

TP9814

TP9815

TP9816

TP9817

TP9818 SC1/COMP1_DET

COMP2_Y+

COMP2_Pb-

COMP2_R_IN

COMP2_Pb+

COMP2_L_IN

COMP2_Y-

COMP2_Pr+

COMP2_Pr-

MDS62110204

GAS3

OPT

MDS62110204

GAS2

OPT

MDS62110204

GAS1

OPT


SCART OPTION BLOCK

98

SMALL_US_KR_EM_JACK PACK_HONGSU_090818

Component2 OPTION BLOCK

PLACE UNDER TUNER


Documents

North/Latin America Europe/Africa ......manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances