2

:lng E_..4=5

Espa5ol ........... 25

Controls ....... 7

Looking inside .......... 8 - 9

Automatic ice and Water

Dispenser ................ 10 =15

Food Storage& Ener Savin Ti s ....... 16

Normal O_ Sounds.. 17

Care & Cleaning ......... 18 = 19

Warranty ...................... 20

Before You CallSolutions tocommo.Prob=ems.............. 21 - 24

I

READ AND SAVE THESE INSTRUCTIONS p_N241_15oo _o5o_

CongratuIations on your purchase of a new refrigerator! Wehere at Electrolux Home Products, inc. are very proud of ourproduct and we are completely committed to providing youwith the best service possible. Your satisfaction is our #1priority.

Please read this Use & Care Manual very carefully. It containsvaluable information on how to properly maintain your newrefrigerator.

We know you'll enjoy your new refrigerator and Thank You forchoosing our product. We hope you consider us for futurepurchases.

PLEASE READ AND SAVETHESE INSTRUCTIONS

This Use & Care Manual provides specific operatinginstructions for your model Use your refrigerator only asinstructed in this manual These instructions are not meant to

cover every possible condition and situation that may occur.Common sense and caution must be practiced when installing,operating and maintaining any appliance.

Pmease record your modem and seriam numbers below forfuture reference.This information is found on the serial

plate tocated inside the refrigerator compartment.

Model Number:

Serial Number:

Purchase Date:

Questions?

1-800-944-9044

(United States)

1-800-265-8352

(Canada)

or visit our web site at ww_',frigidaire, com

Extend Your Warranty ProtectionWith An

Extended Service Contract

OALL 1-800-944-9044

To Enjoy These Benefits:

Total freedom from repair bills sounexpected repairs won't upset your budget,

Fast, convenient toll-free service is just aphone call away,

Top-quaJity repairs by factory-trainedexperts,

Quick access to genuine repJacementparts so you can rest assured yourrefrigerator is repaired with the propercomponents,

PLEASE COMPLETE AND MAIL IN THE PRODUCTREGISTRATION CARD INCLUDED WITH YOUR

REFRIGERATOR.

Please attach sales receipt here for future reference.

FORYOURSAFETY,, Donotstoreorusegasoline,orotherflammableHquidsin

thevicinityofthisoranyotherappliance.Readproductlabelsforwarningsregardingflammabilityandotherhazards.

,, Donotoperatetherefrigeratorinthepresenceofexplosivefumes.

,, Avoidcontactwithanymovingpartsofautomaticicemaker.

,, RemovealIstaplesfromthecarton.Staplescancauseseverecuts,andalsodestroyfinishesiftheycomeincontactwithotherappliancesorfurniture.

CHILDSAFETYDestroyorrecyclethecarton,plasticbags,andanyexteriorwrappingmateriatimmediatelyaftertherefrigeratorisunpacked.ChildrenshouldNEVERusetheseitemstoplay.Cartonscoveredwithrugs,bedspreads,plasticsheetsorstretchwrapmaybecomeairtightchambers,andcanquicklycausesuffocation.

PROPERDISPOSALOFYOURREFRIGERATORORFREEZERRisk of child entrapment

Child entrapment and suffocationare not problems of the past.Junked or abandoned

refrigerators or freezers are stilldangerous - even if they wilI sit for"just a few days." If you are gettingrid of your old refrigerator orfreezer, please follow theinstructions below to help preventaccidents.

Before you throw away your old refrigerator/freezer:

o Remove doors.

_, Leave shelves in place so children may not easily climbinside.

,, Have refrigerant removed by a qualified servicetechnician.

ELECTRICAL INFORMATION

,, The refrigerator must be plugged into its own dedicated115 Volt, 60 Nz,, AC onmy electric outlet. The power cordof the appliance is equipped with a three-prong groundingplug for your protection against electrical shock hazards. Itmust be plugged directly into a properly grounded three-prong receptacle. The receptacle must be installed inaccordance with local codes and ordinances. Consult a

qualified electrician. Do not use an extension cord oradapter p_ug.

,, If the power cord is damaged, it should be replaced by themanufacturer, service technician or a qualified person toprevent any risk.

,, Never unplug the refrigerator by pulling on the powercord. Always grip the plug firmly, and pulI straight outfrom the receptacle to prevent damaging the power cord.

,, Unplug the refrigerator before cleaning and beforereplacing a light bulb to avoid electrical shock.

,, Performance may be affected if the voltage varies by'10% or more. Operating the refrigerator with insufficientpower can damage the compressor. Such damage isnot covered under your warranty.

Do not plug the unit into an outlet controlled by a walIswitch or pull cord to prevent the refrigerator from beingturned off accidentally.

Avoid connecting refrigerator to a Ground Fault Interruptor(GFI) circuit.

3=prorlg g_suaded P!ug

This Owner's Guide provides specific operating instructions foryour model. Use the refrigerator onIy as instructed in this Use &Care Manuai. Before starting the refrigerator, follow theseimportant first steps.

LOCATION

o Choose a ptace that is near a grounded electrical outleLDo Not use an extension cord or an adapter plug.

o If possible, place the refrigerator out of direct sunlightand away from the range, dishwasher or other heatSOUrCeS,

. The refrigerator must be instaIIed on a floor that is leveland strong enough to support a fully loaded refrigerator.

. Consider water supply availability for models equippedwith an automatic ice maker.

INSTALLATION

Installation Clearances

. Allow the following clearances for ease of installation,proper air circulation, and plumbing and electricalconnections:

Sides & Top .................. 3/8"Back ........................... 1"

DOOR OPENING

To Remove Toe Grille:

2.Open freezer and fresh food compartment doors.

Working from left side of toe grille, slip your fingersbetween top of toe grille and cabinet. Gently pullforward until first set oftabs are free. Slide

your hand down past Cabinetthe free tabs and pulIforward again until thesecond set of tabs are

free. Continue this Grille / _-_.,"i

process until all tabs . j_;-<<.

are free and the toe __ _grille can be removed.

I1

(See graphic at top ofpage in right column.)

LEVELING

Ali four corners of your refrigerator must rest firmly on a solid floor_Your refrigerator is equipped with adiustabie front rollers to help levelyour unit. To ensure proper door seal and assist door closing, therefrigerator should be tilted 1/4" (6 ram), front to back.

To Level Your Refrigerator:

1. Remove toe grille, (See "To Remove Toe Gri//e',)

2. Use flat-blade screwdriver or 3/8" socket wrench to adjustfront rollers.

Your refrigerator should be positioned to allow easy access to acounter when removing food. For best use of drawers andfreezer baskets, the refrigerator should be in a position whereboth the refrigerator and freezer doors can be fully opened.

TOE GRILLE INSTALLATION/REMOVAL

To install Toe Grille:

1. Open freezer and fresh food compartment doors.

2. Line up toe grille at base of refrigerator, making sure thefour bottom tabs are resting through holes at base ofcabinet.

3. Starting from Ieft side of toe grille, press in on first top tabusing your thumb and push toe grille forward until it snapsin place. Continue this process until al! tabs are snappedin place and toe grille is secured to refrigerator.

3,

I Raise

i_ iiiii

© s

Check both doors to be sure seals touch cabinet on atl foursides.

Before lnstafling The Water Supply Line, You Will Need:

,, Basic Tools: adjustable wrench, flat-blade screwdriver,and Phillips TM screwdriver

,, Access to a household cold water Iine with water pressurebetween 30 and 100 psi.

,, A water supply line made of ¼ inch (6.4 ram) OD, coppertubing. To determine the length of copper tubing needed,you wilI need to measure the distance from the ice makerinlet valve at the back of the refrigerator to your cold waterpipe. Then add approximately 7 feet (2.1 meters), so therefrigerator can be moved out for cleaning (as shown).

,, A shutoff valve to connect the water supply Iine to yourhousehold water system. DO NOT use a self-piercing typeshutoff valve.

,, A compression nut and ferrule (sleeve) for connecting thewater supply line to the ice maker inlet valve.

To Connect Water Supply Line To lee Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ONwater supply and flush supply Iine until water is clear. TurnOFF water supply at shutoff valve.

3. Unscrew plastic cap from water valve inlet and discard

cap.4. Slide brass compression nut, then ferrule (sleeve) onto

water supply line, as shown.

5. Push water supply line into water valve inlet as far as it willgo (¼ inch). Slide ferrule (sleeve) into valve inlet andfinger tighten compression nut onto valve. Tighten anotherhalf turn with a wrench; DO NOT over tighten.

6. With steel clamp and screw, secure water suppiy line torear panel of refrigerator as shown.

7. Coil excess water supply line (about 2_/2turns) behindrefrigerator as shown and arrange coils so they do notvibrate or wear against any other surface.

8. Turn ON water suppiy at shutoff valve and tighten anyconnections that leak.

9. Reconnect refrigerator to electrical power source.

10. To turn ice maker on, lower wire signal arm (side

mounted) or set the ice maker's On/Off power switch to the

"t" position. (rear mounted)

Plastic Water Tubiegto Ice Maker

I_ Fill Tube

water he

Water Valve

Valve Inbt

• valve

-ousehold water suppl_

(Include enough tubing _nIoos to allowrnowng retngerator out fox cleaning.,

Hinge

--....

_

TO DmSOONNEOTI. Press outer r qg agaF_st face

remove IUDe

TO OO_t ....

insert t

push until matk touches face of fitthg

Tools Necessor.

Ph _s neuu Wrench

DOOR REMOVAL INSTRUCTIONS:

if it is necessary to move the refrigerator through narrow doorways, followthese steps to remove the doors.

NOTE

1. Disconnect electrical supply.

2. Open botf aoors, then remove _oe grille.

3, Close doors.

To Remove Refrigerator Door:

1 Remove _op hinge cover screw on refrigerator door _nd remove cover.

2. Trace around hinge with soft lead oenciI. This wilI make it easier to realign doorswnen they are reelaced.

3. Remove ICe hinge ana ift refrigerator door off bottom singe pin. Set door aside.

4. Remove eonom hinge, if necessary.

5. Reverse this :roceaure to reinstall refrigerator door.

To Remove Freezer Door:

1. Disconnect water Iine coming from ower hinge of freezer aoor at connectionlocated under trent of freezer: Press ouler nng against face of fitting, then pull toremove tube.

2. Remove top hinge cover screw on lreezer door and remove cover.

3. Disconnect wrong harness conneclor plug at ton htnge: D_aceyour thumbs on flatsides of each connector ane Dena both Earts eacK and forth, then with firm grasp,pull both Dleces apart.

4. Trace around hinge wlth soft earl pencil. This wiI make _teas_er to realign doorswnen they are reDIaced.

5. Remove _cs hinge allowing wrong harness _o Dull through hinge and lift freezerdoor off st bottom hinge Din Lay door dowr flat to avoid k_nkIng water line.

6. Remove eo_-comhinge, if necessary.

7. Reverse this procedure to reinstall freezer door.

When DOra doors save seen reinstalled, connect water line by inserting tube andpush until mark loucnes face of fitting, replace _oe gnlle and ptug in electrical powercord. Turn both _empera_ure comro_s to center position. Adjust settings as necessary.

Door Bin

RceContainer

Pica Shelf

Wire Bhelf

Small itemsDoor Bin

Wire Shelf

Door Bin

Small Basket

LB_e Basket

Door Bin

Large Basket

Door Bin

Dai_ Door

Door Bin

Witte Rack

Door Bin

Meat Keeperand Cover

8pi((Safe"_

Fixed She(f

Door Din

EggTray

Speciam Item•Rack

fa(mBottle

Retainer

Snugger

Crisper Pan

and Cover

Fixed

Door Bin

COOL DOWN PERIOD

To ensure safe food storage, aliow the refrigerator to operatewith the doors closed for at least 8 to 12 hours before loadingit with food=

REFRIGERATOR & FREEZER CONTROLS

TEMPERATURE ADJUSTMENT

, After 24 hours, adjust the controls as needed= Adjusttemperatures gradually; move the knob insmallincrements, allowing the temperature to stabilize,

, For cotder temperatures, turn the knob towards Colder=

, For warmer temperatures, turn the knob towards Co_d=

To maintain temperatures, a fan circulates air in therefrigerator and freezer compartments= For good circulation,do not block cold air vents with food items=

Factory Setting fa¢tof7 Settlng

Freezer co.T.o_ Fresh food

Refrigerator & Freezer Controls(Features may vary according to modeL)

TEMPERATURE ADJUSTMENT GUIDE

if Fresh Food Compartment (s Too Warm Turn Fresh Food Control Slightly Towards Colder.

ff Fresh Food Compartment Es Too Cold Turn Fresh Food Control Slightly Towards Cold.

ff Freezer Compartment Es Too Warm Turn Freezer Control Slightly Towards Colder.

ff Freezer Compartment Es Too Cold Turn Freezer Control Slightly Towards Cold,

* To Turn Refrigerator Off Turn Freezer and Fresh Food Controls To O,

MODELS)

This shelf is attached to thefreezer wall beside the ice

dispenser container. Thisconvenient area allows for

storage of pizza and other tallitems placed vertically betweenthe ice dispenser container andthe freezer wall.

ICE CREAM SHELF (SOMEPizza Shelf

[_ODELS)

This shelf attaches to the top ofthe ice dispenser container. Itallows storage of both round andrectangular cartons of yourfavorite ice cream.

TmP-UP SHELF (SOME

MODELS)

A Tip-Up shelf in the freezersection atlows tall items to be

easily stored.Ice Cream Shelf

ADJUSTABLE DOOR BINS

Some models have adjustable door bins that can be moved tosuit individual needs_

To move door bins

1. Lift bin straight up.2. Remove bin.

3. Place bin in desired position.

4. Lower bin onto supports until locked in place.

AdjustabJe Door Bin

* WhiteWestinghouse - SpHUFreeTM

CANTILEVER SHELF ADJUSTMENT

Refrigerator shelves are easily adjusted to suit individualneeds. Before adjusting the shelves, remove all foe&Cantilever shelves are supported at the back of the refrigeraton

To adjust cantilever shelves:

Lift front edge up.Pull shelf out.

Replace the shelf by inserting the hooks at rear of the shelf intothe wail bracket. Lower the shelf into the desired slots and lock

into position.

* Spih'Safe7;_glass shelves (some models) catch and holdaccidental spills. In some models, the * SpiflSafe TM shelves slideout for easy access to food and for fast cleaning. The shelvesslide out independently of their mounting brackets. Just pull thefront of the shelf forward. Shelves can be extended as far as the

stopper will allow but are not removable from their mountincbrackets.

i

Cantilever Sliding Glass ShelfCantilever Glass Shelf

DOOR STORAGE

Door bins and shelves are provided for convenient storage ofjars, bottles, and cans. Frequently used items can be quicklyselected.

Some models have door bins that can accommodate gallon-sized plastic drink containers and economy-sized jars andcontainers. Some bins are adiustable for maximum storagecapacity.

The dairy compartment, which is warmer than the general foodstorage section, is intended for short term storage of cheese,spreads, or butter.

Tilt Out

Fixed Door Bin

TALLBOTTLERETAINER(SOME[VIODELB)

The Tail Bottle Retainer keeos _a containers in the bin frorr

falling forward when opening or closing the retngerator aoor.To install, hold the retainer at the top, and slide it }ver [neoutside wall of the bin. as ShOWnin the diagram. The Tal!Bottle Retainer works best with a Bin Snugger.

SPECIAL ITEM RACK

(SOME MODELS)

The innovative design ofthe Special Item Rackallows you to store a six-pack of 12 ounce drinkcans, a bottle of wine, atwo-Iiter soft drink bottle,or a carton of eggs. TheSpecial Item Rack mountson the left side of yourrefrigerator. To install, justslide the Special ItemRack onto any shelf asshown in the drawing. Special ItemRack

Tall Bottle Retainer (Ieft) and Bin Snugger (right)

CRISPERS (SOME

MODELS)

The crispers, located underthe bottom refrigerator shelf,are designed for storingfruits, vegetables, and other

fresh produce. Wash items inclear water and remove

excess water before placingthem in the crispers. Itemswith strong odors or highmoisture content should bewrapped before storing.

Crisper Drawer

HUMIDITY CONTROL (SOME MODELS}

The Humidity Control, present on some models with crisperdrawers, allows you to adjust the humidity within the crisper.This can extend the life of fresh vegetables that keep best inhigh humidity.

f

Crisper Humidity Control

DELl DRAWER (SOME MODELS}

Some models are equipped with a Deli Drawer for storage ofluncheon meats, spreads, cheeses, and other deli items.

MEAT KEEPER (SOME MODELS}

Some models are equipped with a Meat Keeper. Meat Keepertemperatures can be adjusted by sliding the Meat KeeperTemperature Control in either direction. Use this pan for shortterm storage of bulk meat items, if meats are to be kept Iongerthan one or two days, they should be frozen. The Meat Keeperis fixed and cannot be moved up or down. if fruits or vegetablesare to be stored in the Meat Keeper, set the Meat KeeperTemperature Control to a warmer setting to prevent freezing.

WiNE RACK (SO[VIE

MODELS)

The wine rack stores bottles of

wine, or single two-liter plasticbottles of juice or soda pop. Toinstall, slide the Wine Rackonto the shelf with the curve

facing in. To remove, slide theWine Rack out. Install onside of shelf.

Meat Keeper withTemperature Control

Wine Rack

AUTOMATIC iCE &WATER DJSPENSEFt OPERATING iNSTRUCTiONS

!_om_f.... F_,ol_o Cube Crush Ligh} fil}_lRe,e} I_ck

EXTREMEFREEZE

EXTRAtOE

CUBE

CRUSH

LIGHT

F_LTERSTATUS

LOCK

WATER

i! iii illi ,/ ii i!' i ii i

i i

J i

To freeze food at a faster rate to preserve freshness, push the Touch Pad _ for 3-5 seconds toactivate this feature. A green light will appear above the Touch Pad. Push _the Touch Pad _againfor 3-5 seconds to deactivate.

To increase ice production for special occasions, such as parties, push the Touch Pad @for3-5 seconds to activate this feature. A green light wilI appear above the Touch Pad. Push theTouch Pad O again for 3-5 seconds to deactivate.

Press the CUBE Touch Pad @. to get cubed,_Lice.A green light will appear above the Touch Pad.Press glass against ICE dispensing paddle _ as far up as possible to catch alI ice.

Press the CRUSH Touch Pad @ to get crushed ice. A green light wilI appear above the Touch Pad.

Press glass against ICE dispensing paddle@ as far up as possible to catch alI ice.

Press the LIGHT Touch Pad _ to turn on dispenser light. Press_again to turn the light off.The light also turns on automatically when ice and/or water is dispensed. Replace light bulb withan appliance bulb of the same wattage.

The FILTER STATUS indicator light above the Touch Pad @ will light up each time the dispenseris used. The following filter light indications are:

Green The filter is still operating within its specified Iife cycle.

Amber The filter has reached approximately 80% of its useful life. This is the recommended timeto purchase a replacement filter.

Red The filter is 100% used up. Change the filter as soon as possible.

After the filter cartridge has been changed, press and hotd the FILTER RESET Touch Pad @ for10-15 seconds.

NOTE: The Green, Red and Amber lights will flash when reset is completed.

The Ice & Water Dispenser can be mocked out to prevent unwanted use.

To Lock Out Press the LOCK Touch Pad @ for 3-5 seconds. A Red light will appear abovethe Touch Pad.

To Unlock Press the LOCK Touch Pad _ for 3-5 seconds until the Red light above the

Touch Pad goes out.

To operate the water dispenser, press a glass against the WATER dispensing paddle@. To

stop dispensing water, pull the glass away from the dispensing paddle @. Dispensed water is notcold. For colder water, add crushed ice or cubes before dispensing water. A drip tray located atthe base of the dispenser catches small spills and allows them to evaporate. This drip tray isremovable and dishwasher safe. Do not pour water and excess ice in this area because thereis no drain.

10

AUTOMATICiCE&WATERDISPENSEROPERATINGiNSTRUCTiONS

_ % :J_ _ y-_L ,_!i j_ ,_! _ .¢

O@@@I_e L_ht-

Features may vary according to modem.

Crushed Press the Crushed Touch Pad A to get crushed ice, A red indicator will appear above the Touch Pad, Press glass against

ICE dispensing paddle@ as fa_up as possible to catch all ice,

Cubed Press the Cubed Touch Pad _ to get cubed ice. A red indicator will appear above the Touch Pad. Press glass against ICE

dispensing paddle as far up as possible to catch all ice.

Light On Press the Light On Touch Pad @ to turn on dispenser light. A red indicator will appear above the Touch Pad.

Off Press the Light Off Touch Pad @ to turn off dispenser light. A red indicator will appear above the Touch Pad.Light

WATER To operate the water dispenser, press a g_ against the WATER dispensing paddle@. To stop dispensing water, pull

the glass away from the dispensing paddle _ . Dispensed water is not cold. For colder water, add crushed ice or cubesbefore dispensing water. A drip tray located at the base of the dispenser catches small spills and allows them to evaporate.This drip tray is removable and dishwasher safe. Do not pour water and excess ice in this area because there is no drain.

11

HOWTHEWATERDmSPENSERWORKSThewatertank,locatedbehindthedrawersintherefrigeratorcompartment,automaticallyfillsaswaterisdispensed.Forproperdispenseroperation,therecommendedsupplywaterpressureshouidfallbetween30psiand100psi.Aftertherefrigeratorisconnectedtothewatersupply,filIthewatertankbydrawingoneglassofwater._tmaytakeabout11/2minutesafteractivatingthedispenserpaddlebeforewaterbeginstofillthisfirstglass.Continueflushingthesystemfor3minutestoridthetankandplumbingconnectionsofanyimpurities.ThewaterdispenserhasabuiltinshutoffdevicethatwiIIstopthewaterflowafter3minutesofcontinuoususe.Simplyreleasethedispenserpaddletoresettheshutoffmechanism.

HOWTHEICEDISPENSERWORKS-SIDEMOUNTEDTheicemakerandcontainerarelocatedinthetopofthefreezercompartment.Aftertherefrigeratoris installedproperlyandhascooledforseveralhours,theicemakercan _o,beginmakingicewithin24hours.AirinnewplumbinglinesmaycausetheicemakertocycletwoorthreetimesbeforemakingafulI , _

tray of ice. To begin ice _/__.. /./.production, lower the wiresignal arm to the "down" orON position. With no usage itwilI take approximately 2days to fill the ice container.The ice maker turns off automatically when the ice containerbecomes full. To stop the ice maker, lift the wire signal arm untilit clicks, and locks in the "up" or OFF position.

HOWTHE lOB DISPENSER WORKS -REAR MOUNTED

The ice maker and container are located in the top of thefreezer compartment. After the

refrigerator is installedproperly and has cooled forsevera! hours, the ice maker

can begin making ice within24 hours. Air in new plumbinglines may cause the ice makerto cycle two or three timesbefore making a fulI tray of ice.Ice production is controlled bythe ice maker's On/Off powerswitch. Press the switch to the

"O" position to turn it Off and press it to the "J" position to turn itOn. With no usage it will take approximately 2 days to fill the icecontainer. The ice maker also has a built-in wire signalarm,which automatically stops ice production when the ice binis full. This signal arm should not be used to manually stop theice maker.

The ice maker produces 4 to 6 pounds of ice every 24 hoursdepending on usage conditions. Ice is produced at a rate of 8cubes every 75 to 90 minutes.

Because of new plumbing connections, the first production ofice cubes may be discolored or have an odd flavor. Theseshould be discarded until the cubes made are free ofdiscoloration and taste.

ICE ANDWATER DISPENSER FEATURES

The ice and water dispenser conveniently dispenses chilledwater, and ice cubes or crushed ice, depending on the model.

To operate the ice dispenser, select the ice option desiredusing the touchpad. Press a glass against the dispensingpaddle as far up as possible to catch all ice. To stopdispensing ice, pull glass away from dispensing paddle. Donot remove the glass until the ice has completely dispensed.(Complete instructions for the dispenser operation areattached to the inside of the freezer door.)

ICE DISPENSER TIPS

,, Ice cubes stored too long may deve!op an odd flavor.Empty the ice container and ensure that the wire signalarm is in its "down" or ON position (side mounted) or the

ice maker's On/Off power switch is turned On-set to the '!"

position (rear mounted). The ice maker will then producemore ice,

,, Occasionally shake the ice container to keep iceseparated.

,, Keep the wire signal arm in its "up" or OFF position (sidemounted) or the ice maker's On/Off power switch turned

Off-set to the "O" position (rear mounted) until therefrigerator is connected to the water supply or wheneverthe water supply is turned off.

12

,, If a large quantity of ice is needed at one time, it ls best toremove cubes directly from the ice container.

,, The following sounds are normal when the ice maker lsoperating:

,, Motor running

,, Ice dropping into ice container

+ Water valve opening or closing

+ Ice loosening from tray

, Running water

+ Stop the ice maker when cleaning the freezer and duringvacations.

, If the ice maker wilI be turned off for a Iong period of time,turn the water supply valve to the closed position.

CLEANINGTHE ICE DISPENSER

CIean the dispenser and ice container at reguIar intervals,particularly before you take a vacation or move, or if the icedispenser sticks.

1. Stop ice production by lifting the wire signal arm to the"up" or OFF position (side mounted) or the ice maker's On/

Off power switch turned Off-set to the "O" position (rear

mounted) .

2. Remove ice container by lifting up and out. Empty andcarefully clean the container with mild detergent. Rinsewith clear water. Do not use harsh or abrasive cleaners.

Allow ice container to dry completely before replacing inthe freezer.

3. Remove ice chips and clean the shelf and chute thatsupports the ice container.

4. Replace the ice container. Lower the wire signal arm onthe ice maker to the "down" or ON position (sidemounted) or the ice maker's On/Off power switch is turned

On-set to the "l" position. (rear mounted)and the icemaker wil! resume production.

Remove and empty the ice storage bin if:1. An extended power failure (one hour or longer) causes ice

cubes in the ice storage bin to melt and freeze togetherand jam the dispenser mechanism.

2. The ice dispenser is not used frequently. Ice cubes willfreeze together in the bin and jam the dispensermechanism. Remove the ice storage bin and shake toloosen the cubes.

Auger +--+

13

PURESOURCETM* iCE AND WATER FILTER (SOME

MODELS)

System Startup:

Water supply does not need to be turned off, however, do notuse ice and water dispenser while installing filter=The filtercartridge has aIready been installed in the filter housing at thefactory. Refer to the How The Water Dispenser Works section toproperly fill the system with water.

Order new filter

cartridges through thedealer where you boughtthe refrigerator, contactthe ConsumerAss_gtance Center at 1-

800-944-9044, or go toour web site at

_idaire=com. Itmight be good to ordersome filter cartridgeswhen you first install yourrefrigerator. Be sure toask for the RG-100mureSource TM*

replacement cartridge.

The PureSource TM * NGRG-2000 Ice and Water

Filter System with the RG-100 cartridge is testedand certified by NSF International, the nationallyrecognized and respected, not for profit,certification organization for public health safety.

The PureSource TM*system is tested and certified to ANSl/NSFStandard 42= See performance data sheet for specifications=This system should not be used on water that ismicrobiologically unsafe or with water of unknown qualityunless the water has been adequately disinfected before orafter traveling through the filtration system.

,, Rated Capacity - 400 gallons,, Rated service flow - .5 GPM,, Maximum Rated Pressure - 100 PSI

,, Maximum Operating Temp= - 100° F

Changing the Filter:

Water conditions vary throughout the world, but changing thewater filter every 6 - 9 months normally will ensure the highestpossible water quality= The Filter Status light wiII turn red after400 gallons of water has flowed through the ice and waterdispenser (some models). Also, if the filter has been in arefrigerator that has not been in use for awhiIe (during movingfor example), change the filter before reinstalling the refrigerator=

The dispenser system wilI also operate without filtration (withfilter cartridge removed)=

To change fitter:

It is not necessary to turn the water suppiy off to change the filter.

1= Open freezer door and leave open until filter change iscomplete=

2= Set ice maker wire signal arm to the OFF (up) position (side

mounted) or the ice maker's On/Off power switch turned Off-set

to the "O" position (rear mounted)=

3. Hold filter cup firmty, and unscrew towards Ieft (Some watercould leak out as you remove cup. This is normaL)=Filtercartridge should come down with cup= If cartridge remains inhousing, pull down gently, while b.,vistingfilter back and forth=

4= Rinse out cup under running water=

5. The large o-ring that seals the filter system sets in the o-ringgroove down inside the cup= Should the o-ring fail out duringfilter cartridge replacement, simply place it back in the grooveprior to screwing the cup back in place. If the o-ring becomesdamaged, you wilI need to order one from the ConsumerAssistance Center=

6= Discard old filter cartridge=

7. Remove new filter cartridge from packaging=Place in cup=Theend with the small o-ring should be up, out of the cup=

8= Screw cup, with fiIter, back onto housing=Do Not Use WrenchTo ReinetalB Cup= Filter cartridge will self-align as cup istightened. Be sure cup is completely tightened withPureSource TM logo facing outward=Do Not Tighten Past Stop.

9. Set ice maker wire signal arm to the ON (down) position (side

mounted) or the ice maker's On/Off power switch is turned

On-set to the "t" position=(rear mounted).

10= Check for leaks=Open refrigerator door=Wipe any water dropletsfrom the filter cup. Filla glass with water. If there is a leak,unscrew filter cup, and reinsert the filter cartridge=Checkplacement of large O-ring= Reinstall filter cup, making certain it istightened completely=

11= To condition filter system and purge air from water line, filI aglass with water. Continue flushing the system for approximately3 minutes to assure that the purest water possible is stored inthe water tank.

* White Westinghouse uses the name CrystalClear insteadof PureSource,but they are the same filter.14

PURESOURCE2TM*iCE ANDWATER FRONT FILTER(SOME MODELS)

filter before reinstalling the refrigerator. The dispenser systemwill also operate without filtration (with filter cartridge removedand bypass installed).

System Startup:Water supply does not need to be turned off, however, do not

use ice and water dispenser while installing filter.

The filter cartridge has already been installed in the filterhousing at the factory. Refer to the How T,_e Water DispenserWorks section to properly fill the system with water.

Order new filter

cartridges through thedealer where youbought the refrigerator,contact the ConsumerAssistance Center at 1-

800-944-9044, or go toour web site at

_idaire.com. itmight be good to ordersome filter cartridgeswhen you first installyour refrigerator. Besure to ask for the FC-100 PureSource TM*replacement cartridge.

Fiuter

and CUickTo _nstaU TO Release

The PureSoume2 rM"Ice and Water Filter

System NGFC 2000 with the PureSoume2 rM"cartridge FC 100 is tested and certified byNSF international, the nationally recognizedand respected, not for profit, certification

organization for public health safety. The PureSource2 rM*Filter system is tested and certified to ANSI/NSF Standards42 and 53. See performance data sheet for specifications.This system should not be used on water that ismicrobiologicaIIy unsafe or with water of unknown qualityunless the water has been adequately disinfected before orafter traveling through the filtration system.

. Rated Capacity - 400 gallons,, Rated service flow - .5 GPM,, Maximum Rated Pressure - 100 PSI

. Maximum Operating Temp. - 100 ° F

To change filter:It is not necessary to turn the water supply off to change thefilter.

1. Set ice maker wire signal arm to the OFF (up) position (side

mounted) or the ice maker's On/Off power switch turned Off-setto the "O" position (rear mounted).

2. Push the Filter Release Button, located to the right of thefilter cartridge, to release the filter from the housing. Tominimize the possibility of the filter falling out of thehousing during removal, it would be best to hold thefilter as it moves out toward you.

3. Pull the old filter cartridge straight out of the housing.4. Discard the old filter.

5. Remove the new filter cartridge from the packaging andinsert into the filter housing the same way the old onecame out.

6. When the cartridge is almost in, you will feel it stop againstthe clip assembly in the back of the housing. The clipassembly holds the filter cartridge firmly in piace. At thispoint, you wilI need to push firmly until the cartridgesnaps fully in place. When completely in place, the front ofthe filter cartridge will be flush with the front of the housing.

7. Set ice maker wire signal arm to the ON (down) position (sidemounted) or the ice maker's On/Off power switch is turned On-

set to the 'T'position. (rear mounted).

8. Fill a glass with water. As you are doing this, check forleaks at the filter housing. There will be noticable spurtsand sputters as the system pushes the air out through thesystem and out the dispenser nozzle. This is normal

9. After you have run one glass of water, continue to flush thesystem for approximately 3 minutes to assure that thepurest water possible is stored in the water storage tank.

Changing the Filter:Water conditions vary throughout the world, but changing thewater filter every6 - 9 months normally will ensure the highest possible waterquality. The Fiiter Status light wiil turn red after approximately400 gallons of water has flowed through the ice and waterdispenser. Also, if the filter has been in a refrigerator that has notbeen in use for awhiie (during moving for example), change the

* White Westinghouse uses the name CrystaIClear instead of PureSource, but they are the same filter.

15

FOODSTORAGEmDEAS

Fresh Food Storage

,, The fresh food compartment should be kept between 34 °F and 40° F with an optimum temperature of 37 ° R

,, Avoid overcrowding the refrigerator shelves. This reducesthe circulation of air around the food and results in unevencooling.

Fruits and Vegetables

,, Storage in the crisper drawers traps moisture to helppreserve the fruit and vegetable quality for longer timeperiods.

Meat

,, Raw meat and poultry should be wrapped securely soleakage and contamination of other foods or surfacesdoes not occur.

Frozen Food Storage

,, The freezer compartment should be kept at 0° F or lower.

,, A freezer operates most efficiently when it is at least 2/3full.

Packaging Foods for Freezing

_, To minimize dehydration and quality deterioration, usealuminum foil, freezer wrap, freezer bags or airtightcontainers. Force as much air out of the packages aspossible and seal them tightly. Trapped air can cause foodto dry out, change color, and develop an off-flavor (freezerburn).

,, Wrap fresh meats and poultry with suitable freezer wrapprior to freezing.

,, Do not refreeze meat that has completely thawed.

Loading the Freezer

,, Avoid adding too much warm food to the freezer at onetime. This overloads the freezer, slows the rate of freezing,and can raise the temperature of frozen foods.

,, Leave a space between the packages, so cold air cancirculate freely, allowing food to freeze as quickly aspossible.

_, Avoid storing hard-to-freeze foods such as ice cream andorange iuice on the freezer door shelves. These foods arebest stored in the freezer interior where the temperaturevaries less.

ENERGY SAVING IDEAS

'_$ -MOS"-", " Locate the refrigerator in the cooIesti&_ _°_"_ part of the room, out of direct sunlight,

,_'-° _'__ _! and away from heating ducts or

_; ,'_ registers. Do not place the refrigeratornext to heat-producing appliances suchas a range, oven, or dishwasher. If this

is not possible, a section of cabinetry or an added layer ofinsulation between the two appliances will help the refrigeratoroperate more efficiently.

,, Level the refrigerator so that the doors close tightly.

_, Refer to this Use & Care Manual for the suggestedtemperature control settings.

_, Periodic cleaning of the condenser will help therefrigerator run more efficiently. See the Care andC/eaning Chart on page 18.

,, Do not overcrowd the refrigerator or block cold air vents.Doing so causes the refrigerator to run longer and use

more energy._, Cover foods and wipe containers dry before placing them

in the refrigerator. This cuts down on moisture build-upinside the unit.

_, Organize the refrigerator to reduce door openings.Remove as many items as needed at one time and closethe door as soon as possible.

16

UNDERSTANDmNGTHE SOUNDSYOU MAY HEAR

Your new high-efficiency refrigerator may make unfamiliarsounds. These are alI normal sounds and soon wilI become

familiar to you. They also indicate your refrigerator is operatingas designed. Hard surfaces, such as vinyl or wood floors,walls, and kitchen cabinets may make sounds morenoticeable. Listed below are descriptions of some of the mostcommon sounds you may hear, and what is causing them.

A. Evaporator

The flow of refrigerant through the evaporator maycreate a boiling or gurgling sound.

B. Evaporator Fan

You may hear air being forced through the refrigeratorby the evaporator fan.

C. Defrost Heater

During defrost cycles, water dripping onto the defrostheater may cause a hissing or sizzling sound. Afterdefrosting, a popping sound may occur.

D. Automatic ice Maker

If your refrigerator is equipped with an automatic icemaker, you will hear ice cubes falling into the ice bin.

E. Cold Control & Automatic Defrost Control

These parts can produce a snapping or clicking soundwhen turning the refrigerator on and off.

F. Condenser Fan

You may hear air being forced through the condenserby the condenser fan.

G. Compressor

Modern, high-efficiency compressors operate muchfaster than older models. The compressor may have ahigh-pitched hum or puisating sound.

H. WaterValve

If your refrigerator is equipped with an automatic icemaker, you will hear a buzzing sound as the watervalve opens to fill the ice maker during each cycle.

L Drain Pan (not removable)

You may' hear water running into the drain pan duringthe defrost cycle.

d. Condenser

May create minimal sounds from forced air.

17

Keepyourrefrigeratorandfreezercleantopreventodorbuild-up.Wipeupanyspillsimmediatelyandcleanbothsectionsatleasttwiceayear.Neverusemetallicscouringpads,brushes,abrasivecleanersorstrongalkalinesolutionsonanysurface.Donotwashanyremovablepartsinadishwasher.Always unplug the electrical power cord from the wall oudet before cleaning.

Care & Cleaning Chart

Part Cleaning Agents Tips and Precautions

Interior/Door Use 2 tablespoons of baking soda in 1 quart of warm water. Be sure toLiner • Soap and water

wring excess water out of sponge or cloth before cleaning around• Baking soda and water controls, light bulb or any electrical part.

Door Gaskets • Soap and water Wipe gaskets with a clean soft cloth.

Drawers/Bins • Soap and waterDo not wash any removable items (bins, drawers, etc.) in dishwasher.

Glass Shelves• Soap and water Allow glass to warm to room temperature before immersing in warm• Glass cleaner water.

• Mild liquid sprays

Toe Grille • Soap and water Vacuum dust from front of toe grille. Remove toe grille (See illustration on• Mild liquid sprays page 4). Vacuum backside and wipe with sudsy cloth or sponge. Rinse• Vacuum attachment and dry.

Exterior and • Do not use commercial household cleaners, ammonia, or alcohol to clean

Handles • handles. Use a soft cloth to clean smooth handles. Do Not use a drycloth to clean smooth doors.

Exterior andHandles

(StainlessSteel Models

Only)

Soap and waterNon Abrasive Glass

Cleaner

Soap and waterAmmoniaStainless SteelCleaners

Condenser • Vacuum attachmentCoils

Never use CHLORIDE to clean stainless steel.

Clean stainless steel front and handles with non-abrasive soapy waterand a dishcloth. Rinse with clean water and a soft cloth. Wipe stubbornspots with an ammonia-soaked paper towel, and rinse. Use a non-abrasive stainless steel cleaner. These cleaners can be purchased atmost home improvement or major department stores. Always followmanufacturer's instruction. NOTE: Always, clean, wipe and dry with thegrain to prevent cross-grain scratching. Wash the rest of the cabinetwith warm water and mild liquid detergent. Rinse well, and wipe dry with aclean soft cloth.

Use the dusting tool attachment on your vacuum to remove dust build-upon the condenser coils (see item "J" in illustration on page 17 for location).

18

REPLACING UGHT BULBS

1. Unplug refrigerator.

2. Wear gloves as protection against possible broken glass.

3. Remove light cover, if necessary.

4. Unscrew and replace oId bulb with an appliance bulb ofthe same wattage.

5. Replace light cover, if necessary.

6. Remember to plug the refrigerator back in.

Light SocketsLocated Behind

or

Refrigerator Light Replacement

/

LightBulb

Located Behind RightRear of Ice Container

Crisper Light Replacement (Models may vary)

Vacation and Moving Tips

ShortVacations

LongVacations

Freezer Light Replacement

. Leave refrigerator operating during vacations of 3 weeks or less.

. Use all perishable items from refrigerator compartment.

. Turn automatic ice maker off, even if you will only be gone for a few days.

. Remove all food and ice if you will be gone one month or more.

. Turn controls to "O" ( the OFF position) and disconnect power.

. Turn off automatic ice maker and turn water supply valve to closed position.

. Clean interior thoroughly.

. Leave both doors open to prevent odors and mold build-up. Block doors open ifnecessary.

• Remove all food and ice.

• If using handcart, load from side.Moving

° Adjust rollers all the way up to protect them during sliding or moving.• Pad cabinet to avoid scratching surface.

19

REFRIGERATOR WARRANTY Yourrefrigerator is protected by this warranty

WARRANTY THROUGH OUR AUTHORIZED SERVICERS, THE CONSUMER WILL BE

PERIOD WE WILL: RESPONSIBLE FOR:

FULL ONE-YEAR One year from Pay all costs for repairing or replacing any parts of this Costs of service calls that are listed under

WARRANTY odginal purchase appliance which prove to be defective in materials or NORMAL RESPONSIBILITIES OF THE

date workmanship Excludes original and replacement Ice & Water CONSUMER.*

filter cartridges (if equipped) Odginal and replacement

cartridges are warranted for 30 days (parts only)

LIMITED 2"d- 5TM Second through fifth Repair or replace any parts in the cabinet liner or sealed Costs for pickup and delivery of the appliance

YEAR WARRANTY years from original refrigeration system (compressor, condenser, evaporator, required because of service Costs for _abor, parts

(Cabinet Liner and purchase date dryer or tubing) which prove to be ddecfive in materials or and transportation other than with respect to the

Sealed System) workmanship cabinet liner or Sea_ed Refrigeration System

LIMITED Time periods listed All of the provisions of the full warranties above and the Costs of the technician's travel to the home and any

WARRANTY above exclusions listed below apply costs for pick up and delivery of the appliance

(Applicable to the required because of service

StateofAlaska)

in the U.S.A..andPuerto Rico,your applianceiswarrantedby ElectroluxMajor AppliancesNorfbAmerica,a divisionof ElectroluxHome Products,inc. In Canada,yourappliance iswarrantedby ElectroluxMajorAppliancesNorthAmerica,a divisionof ElectroluxCanadaCorp.ElectroluxHomeProducts,Inc.and ElectroluxCanadaCorp.are referredto in this warrantyas "Electrolux".We authorizeno personto changeor add to any of ourobligationsunderthis warranty.Our obligationsfor serviceand partsunder this warrantymustbe performedby usor an authorizedElectroluxservicer.

*NORMALRESPONSIBILITIESOF THE CUSTOMER

EXCLUSIONS

This warrantyappliesonly to products in ordinaryhousehold use, and the consumer is responsible for the itemslisted below:

1. Proper useof tbe appliancein accordancewith instructionsprovidedwith the product.2. Proper installationby an authorized servicer in accordancewith instructionsprovided with the appliance and in

accordancewithall localplumbing,electricaland/orgas codes.3. Proper connection to a grounded power supply of sufficient voltage, replacementof blown fuses, repair of loose

connectionsordefects in housewiring.4. Expensesfor makingthe appliance accessiblefor servicing,such as removalof trim, cupboards,shelves, etc.,which

are nota partof the appliancewhen it wasshippedfrom the factory.5. Damagesto finish after installation.6. Replacementof light bulbsand/orfluorescenttubes (onmodetswiththese features).

This warranty does not cover the following:1. CONSEQUENTIALOR INCIDENTALDAMAGES SUCH AS PROPERTYDAMAGEAND INCIDENTALEXPENSES

RESULTINGFROMANYBREACHOF THIS WRITTENORANY IMPLIEDWARRANTY.

Note: Somestates do not allow the exclusionor limitationof incidentalor consequentialdamages,so this limitation orexclusionmaynotapply to you.

2. Servicecalls which do not involvemalfunctionor defects in workmanshipor material, or for appliancesnot in ordinaryhouseholduse.Theconsumershall payforsuch servicecalls.

3. Damages caused by servicesperformed by servicers other than Electrolux,or its authorizedservicers; use of partsother than genuine Electroluxparts; obtained from persons other than such servicers; or external causes such asabuse, misuse,inadequatepowersupplyoracts of God.

4. Productswithoriginalserial numbersthat havebeen removedoralteredand cannot be readilydetermined.

iF YOU NEEDSERVICE

Keep your bill of sale, delivery slip, or some other appropriatepayment record. The date on the bill establishes thewarranty period should service be required. If service is performed, it is in your best interest to obtain and keep allreceipts. Thiswritten warrantygivesyou specific legal rights.You mayalso haveother rightsthat vary from state to state.Serviceunderthis warranty mustbe obtainedby contactingElectrolux.

This warrantyonly appliesin the 50 Statesof the U.S.A.and PuertoRico,and Canada.Productfeaturesor specificationsas describedor illustratedaresubjectto changewithoutnotice.

USA800-944-9044

EIectroluxMajorAppliancesNorthAmerica,a divisionof ElectroluxHomeProducts,Inc.P.O.Box 212378

Augusta,GA 30917

Canada800-265-8352

Electrotux Major Appliances North America,a division of Etectrolux Home Products, Inc.

5855 Terry Fox WayMississauga, Ontario

L5V 3E4

2O

1-800-944-9044 (United States)

1-800-265-8352 (Canada)

PROBLEM J

RUNNING OF REFRIGERA TOR

CAUSE J

Visit our web site at

www.frigidaire.com.

CORRECTION

Compressor does not run.

Refrigerator runs toomuch or too long.

• Freezer control is set to "O".

• Refrigerator is in defrost cycle.

Plug at wall outlet isdisconnected.

House fuse blown or trippedcircuit breaker.

Power outage.

Room or outside weather ishot.

Refrigerator has recently beendisconnected for a period oftime.Automatic ice maker is

operating.Doors are opened toofrequently or too long.Refrigerator/freezer door maybe slightly open.

Freezer control is set too cold(control found in refrigeratorsection).Refrigerator/freezer gasket isdirty, worn, cracked, or poorlyfitted.

Condenser is dirty.

• Set freezer control. See Temperature Controls section.• This is normal for a fully automatic defrost refrigerator.

The defrost cycle occurs periodically, lasting about 30minutes.

• Ensure plug is tightly pushed into outlet.

Check/replace fuse with a 15 amp time-delay fuse.Reset circuit breaker.

Check house lights. Call local Electric Company.

It's normal for the refrigerator to work longer underthese conditions.

It takes 8-12 hours for the refrigerator to cool downcompletely.

• Ice maker operation causes refrigerator to run slightlymore.

• Warm air entering the refrigerator causes it to runmore. Open doors less often.

• Ensure refrigerator is level. Keep food and containersfrom blocking door. See PROBLEM sectionOPENING/CLOSING OF DOORS/DRAWERS.

• Set refrigerator control to warmer setting untilrefrigerator temperature is satisfactory. Allow 24 hoursfor temperature to stabilize.

• Clean or change gasket. Leaks in door seal will causerefrigerator to run longer in order to maintain desiredtemperatures.Clean condenser. See Care & Cleaning Chart in Careand Cleaning section.

Compressor goes off and • Thermostat keeps the • This is normal. Refrigerator goes on and off to keepon frequently, refrigerator at a constant temperature constant.

temperature.

TEMPERA TURE$ ARE TOO COLD

Freezer temperature too • Freezer control is set too cold. • Set freezer control to a warmer setting. Allow 24 hourscold. Refrigerator for temperature to stabilize.temperature is satisfactory.

Refrigerator temperature • Refrigerator control is set too • Set refrigerator control to a warmer setting. Allow 24too cold. Freezer cold. hours for temperature to stabilize.temperature is satisfactory.

Food stored in drawers • Refrigerator control is set too • See solution above.freezes, cold.

Food stored in Meat • Meat Keeper Temperature • Adjust Meat Keeper Temperature Control to a lowerKeeper freezes (some Control set too cold. setting. (Meat should be stored at a temperature justmodels), below the freezing point for maximum fresh storage

time. It is normal for ice crystals to form clue to themoisture content of meat.)

21

PROBLEM [ CAUSE [ CORRECTION

TEMPERA TUllES ARE TOO WARM

Freezer/Refrigeratortemperature is too warm.

• Doors are opened toofrequently or too long.

• Door is slightly open.

• Condenser is dirty.

• Warm air enters the refrigerator whenever the door isopened. Open the door less often.

• See PROBLEM section OPENING/CLOSING OFDOORS/DRAWERS.

• Clean condenser. See Care & Cleaning Chart in Careand Cleaning section.

Freezer temperature is too • Freezer control is set too • Set freezer control to a colder setting. Allow 24 hourswarm. Refrigerator warm. for temperature to stabilize.temperature is satisfactory.

Refrigerator temperature is • Refrigerator control is set too • Set refrigerator control to a colder setting. Allow 24too warm. Freezer warm. hours for temperature to stabilize.temperature is satisfactory.

Temperature in the Meat • Meat Keeper Temperature • Adjust Meat Keeper Temperature Control to a colderKeeper is too warm (some Control is set too warm. setting.models).

WA TER/MOISTURE/FROST INSIDE REFRIGERATOR

• Weather is hot and humid.Moisture collects on insideof refrigerator walls.

• Door is slightly open.

• Door is opened too often or toolong.

• Open containers.

• The rate of frost buildup and internal sweatingincreases.

• See PROBLEM section OPENING/CLOSING OFDOORS/DRAWERS.

• Open door less often.

• Keep containers covered.

Water collects on bottom • Vegetables contain and give • It is not unusual to have moisture on the bottom side ofside of drawer cover, off moisture, the cover.

• Move humidity control (some models) to lower setting.

Water collects in bottom of • Washed vegetables and fruit • Dry items before putting them in the drawer. Waterdrawer, drain while in the drawer, collecting in bottom of drawer is normal.

WA TER/MOISTURE/FROST OUTSIDE REFRIGERATOR

Moisture collects on • Weather is humid. • This is normal in humid weather. When humidity isoutside of refrigerator or lower, the moisture should disappear.between doors. • Door is slightly open, causing • See PROBLEM section OPENING/CLOSING OF

cold air from inside refrigerator DOORS/DRAWERS.to meet warm air from outside.

AUTOMATIC ICE MAKER

• Move wire signal arm to the "down" or ON position.Ice maker is not makingany ice.

• Ice maker wire signal arm is inthe "up" or OFF position.

• Household water line valve isnot open.

• Freezer is not cold enough.

• Saddle valve on cold water

pipe is clogged or restricted byforeign material.Check to see if the waterdispenser is dispensing water.

• Turn on household water line valve.

• See PROBLEM section TEMPERATURES ARE TOOWARM.

• Turn off household water line valve. Remove valve.

Ensure that valve is not a self-piercing saddle valve.Clean valve. Replace valve if necessary.

• If not, the ice & water filter cartridge is clogged orrestricted by foreign material, and must be replaced.

22

Ice maker is notmaking enough ice.

PROBLEM 1 CAUSE

A UTOMA TIC ICE MAKER (CONTINUED)

• Ice maker is producing less icethan you expect.

Ice maker will not stopmaking ice.

Ice maker is not

separating the icecubes.

Ice has bad odor andtaste.

• Freezer is not cold enough

• Household water line valve is

not completely open• Check to see if water

dispenser is dispensing slowerthan normal

Ice maker wire signal arm isbeing held down by some itemin the freezer

• Ice cubes are not being usedfrequently enough

• Ice cubes are hollow or smallerthan normal

• Ice has picked up odor orflavor from strong food storedin refrigerator or freezer

• Water running to ice makerhas poor taste or odor

• Ice not used frequently enough

ICE DISPENSER

J CORRECTION

Ice maker should produce approximately 4 - 5 poundsof ice every 24 hours Extra Ice should produce up to 8pounds of ice every 24 hoursSee PROBLEM section TEMPERATURES ARE TOOWARM.Turn on household water line valve

If it is, replace the ice & water filter cartridge

• Move item and release wire signal arm Remove anyice cubes that are frozen together over the wire signalarm

• Remove and shake ice container to separate cubes

• The ice & water filter cartridge may be cloggedReplace filter cartridge

• Cover foods tightly Discard stale ice Ice maker willproduce fresh supply.

• Add filter to water supply line Consult a waterpurifying company

• Discard stale ice

Dispenser will notdispense ice.

Ice dispenser isjammed.

Ice storage container is empty

Freezer temperature is set toowarm

Household water line valve is

not open.

Freezer door is not closed

Ice dispensing arm has beenheld in for more than 4-5minutes

• Ice has melted and frozen

around auger due to infrequentuse, temperature fluctuations,and/or power outages

• Ice cubes are jammedbetween ice maker and backof ice container

• Ice cubes are frozen together

Ice cubes are hollow or smallerthan normal.

• When the first supply of ice is dropped into thecontainer, the dispenser should operate

• Turn freezer control to a higher setting so that icecubes will be made. When first supply of ice is made,dispenser should operate.

• Open household water line valve Allow sufficient timefor the ice to be made. When ice is made, the

dispenser should operate• Ensure freezer door is closed

• Motor is overloaded. Motor overload protector willreset in approximately 3 minutes Ice can then bedispensed.

• Remove ice container, thaw, and empty the contentsClean container, wipe dry, and replace in properposition When new ice is made, dispenser shouldoperate

• Remove ice cubes that are jamming the dispenser.

Use the dispenser often so that cubes do not freezetogetherThe ice & water filter cartridge could be clogged.Replace the filter cartridge. Dispensing systemoperates best at 30 - 100 psi water pressure Wellwater pressures should fall within this range

23

PROBLEM [ CAUSE _ CORRECTION

WATER DISPENSER

Dispenser will notdispense water.

Water has an odd tasteand/or odor.

Household water line valve is

not open.Freezer door is not closed.

Ice & water filter cartridge isclogged.

Front filter not fully installed, ifequipped

Water has been in the tank fora period of time.Unit not properly connected tocold water line.

Tubing used in the householdwater supply and installationmay affect water taste andodor.

Water has a high mineralcontent.

• Open household water line valve. See PROBLEMsection ICE MAKER IS NOT MAKING ANY ICE.

• Ensure that freezer door is closed.

• Replace filter cartridge.

Push filter in until you hear a "click". Filter should beflush with cabinet.

• Draw and discard 10 - 12 glasses of water to freshenthe supply and completely rinse out the tank.

• Connect unit to cold water line that supplies water tothe kitchen faucet.

• For best results, use copper tubing for waterconnections.

• • Contact water treatment plant for help.

Water pressure is • Cut-off and cut-on pressures • Have someone turn up the cut-off and cut-on pressureextremely low. are too low (well systems on the water pump system (well systems only).

only).• Reverse osmosis system is in • It is normal for a reverse osmosis system to be below

regenerative phase. 20 psi during the regenerative phase.

ODORS IN REFRIGERATOR

Interior is dirty. • Interior needs to be cleaned. / • See Care & Cleaning Chart in Care and Cleaning

[ section.

• Food with strong odors is in • Cover food tightly.refrigerator.

OPENING/CL OSING OF DOORS/DRA WERS

Door(s) will not close. • • Close both doors gently.Door was closed too hard,causing other door to openslightly.Refrigerator is not level. Itrocks on the floor when moved

slightly.Refrigerator is touching a wallor cabinet.

• Ensure floor is level and solid, and can adequatelysupport the refrigerator. Contact a carpenter to correcta sagging or sloping floor.

• Ensure floor is level and solid, and can adequatelysupport the refrigerator. Contact a carpenter to correcta sagging or sloping floor.

Drawers are difficult to • Food is touching shelf on top • Keep less food in drawer.move. of drawer.

• Track that drawers slide on is • Clean drawer, rollers, and track. See Care & Cleaningdirty. Chartin Care and Cleaning section.

LIGHT BULB IS NOT ON

Light bulb is not on. • Light bulb is burned out.

• Light switch is stuck.

• No electric current is reachingrefrigerator.

• See Replacing Light Bulbs in Care and Cleaningsection.

• Light switch is located on side of refrigerator andfreezer liners.

• See PROBLEM section RUNNING OFREFRIGERATOR.

24