Upload
jagannath-sardar
View
327
Download
2
Embed Size (px)
Citation preview
Indian Institute of Technology Delhi 1
Noise Control in Textile Machineries
Jagannath Sardar
(2008TTZ8165)
Submitted to
Prof. K. Gupta Department of Mechanical Engineering
Department of Textile Technology
Indian Institute of Technology Delhi New Delhi
Indian Institute of Technology Delhi 2
Noise control in Textile Machineries: Contents: Page:
1. Introduction: ....…………………………………………… 1
2. Definitions and Background:…. …………………………. 3
2.1 Noise Control Principles………………………………... 4
2.2 Approach to Analysis of Problems……………………... 5
3. Analytical Survey of Noise Study in Textile Industry:....... 6
3.1 Spectrum Analysis………………….…………………… 9
3.2 Standards for noise abatement in industry...…………….. 10
3.3 The Machinery Directive………………………………… 10
4. Structure of Textile Industry:……………………………… 12
4.1. Machineries in Spinning and Noise emission..………….. 12
4.1.1. Existing mechanism of Noise control in Spinning..…. 14
4.2. Machineries in Fabric manufacturing and Noise emission... 18
4.2.1. Existing mechanism of Noise control
in Fabric Manufacturing……………………………… 23
5. Some ideas to control noise in textile machinery:..………… 24
5.1. Active Noise Control…………………..…………………… 25
5.2. Passive Noise Control…………………………….……….. 27
5.2.1. Primary function of Damping materials…………..…… 28
5.2.1.1Definition………………………..………………… 28
5.2.1.2 How does the damping material works……………. 29
5.2.2. Function of Barrier materials…………………..……….. 30
5.2.2.1 How does the barrier material works……………… 31
5.2.3. Function of Absorption materials……..…………………. 32
5.2.3.1. How does the absorption material works………….. 33
6. Conclusion:…………………………………………………….. 35
7. Reference:…….………………………………………………….. 37
Indian Institute of Technology Delhi 3
Acknowledgement
I would like to show my high gratitude to our Respected Sir, Prof. Kshitij
Gupta, who has taken the course Design for Noise, Vibration and Harshness
and I have got a plenty of knowledge regarding Noise and Vibration from his
kind teaching. Before doing this course I have had least knowledge about Noise
and Vibration. Even I did not know the exact definition of sound as well as
Vibration.
I am also grateful to my entire classmates of this course. Specially, I am thankful
to Mr. Changadev Desai who has helped me to understand the course as well. I
am also thankful to Mr. Ajay, M.Tech final year student, who has taken care of
us during practical classes of the same course.
Indian Institute of Technology Delhi 4
1. Introduction: Textile is one of the major economic Industries all over the world. In the field of noise
at the workplace, in spite of national regulations on noise at work in force for many
years, lots of people are still getting hearing losses due to machinery noise throughout
the world. In order to progress, there was a need for a policy enforcing noise reduction
at source at the design stage and allowing market forces to encourage less noisy
machinery being put on the market. This was made possible in Europe through a
specific European regulation [1]. In parallel to the strong action on noise reduction at
source at the design stage, a standardization programme developed at the European and
international levels on workplace noise in particular on designing low-noise workplaces,
designing means to reduce noise on the propagation path and measuring their
effectiveness.
Now a days the machine layout and operation pattern has been changed in textile
industry. Management of the industry are concerned to preserve floor space and
optimize production in both the natural and man-made fibres industries. Noise in the
mills and factories is increasing, and one of the main reasons is that in the face of keen
competition and already on a 24 h basis, machines are being operated at speeds higher
than ever before to increase production rates. This is possible to a great extent with the
man-made fibres; continuous threads can be produced and wound more quickly because
of their inherent strength and other advantageous properties compared with natural
fibres. As a direct result of the speed increase, out of balance forces and vibration
increase and more energy is released as sound [2] Due to the complex nature of Textile industry, versatile machineries are used in the field
of textile product. Different type of machineries produces different level of noise.
Generally workers are exposed in that level of sound during production. They have been
effecting by that sound at any instance.
OSHA (Occupational Safety and Health Act 1970) prescribed permissible exposures in
industries. These levels are shown in the table below (Table 1): [3]:
Indian Institute of Technology Delhi 5
In a textile mill, minimum and maximum noise level can be achieved as 82.82 dBA and
102.3 dBA (approximately) respectively [4].
To prevent health hazards of the workers in that level of sound, different type of
techniques can be applied. But due to unconcerned and un educated workers, the
implementation of those techniques are partially failure. This is a challenging job to
prevent noise in textile industry as well as enlightening to the unconcerned workers and
administrative in Textile industry.
In this literature we will discuss about some approaches to make a pleasant working
environment not only for worker but also the beneficial for the management of the
Textile Sociaty.
Limiting Daily Exposure Time (h)
A-Weighted Sound Level Slow Response
(dBA) 8 90 6 92 4 95 3 97 2 100
1.5 102 1 105
0.5 110 Less Than 0.25 115
Table 1.1: Permissible daily noise exposure limits for industrial noise (OSHA)
Indian Institute of Technology Delhi 6
2. Definitions and Background:
What is Noise? Noise is disagreeable or undesired sound by the recipient. In many
instances, noise is a relative definition of a sound since one person’s music may be
another person’s noise. It is difficult to give a very clear definition of an irritating noise.
Generally, noise is an unwanted sound, regardless of its intensity or duration [5].
Noise Pollution has been recognized as a major threat to human well being. Much
discussion and legislation has evolved in an attempt to recognize and combat the
problem of noise pollution. It has been recognized that noise, of sufficient intensity, can
damage hearing and be classified as a hazard. In combating the problem of noise
pollution it is necessary to use a means of measuring noise levels and a system of
classification. The decibel is a number which relates sound intensity or sound pressure.
When most people use the term decibel or discuss noise levels in decibels they are
referring to decibels as related to the “A-weighted” scale or, dBA [3].
The A-weighted scale parallels the sensitivity of the human ear and uses the lowest
audible sound that the human ear can detect as the reference point for determining the
decibel level of a noise. The reference intensities used above represent the threshold of
audibility where sound is just loud enough to be heard. At 140 decibels or more acute
pain is experienced. Some common noise values are as follows:
Ordinary conversation – 60 dBA
Heavy traffic – 80 dBA
Cocktail Party – 90 dBA
Moving subway train – 100 dBA
Riveting gun – 130 dBA
Hard rock band – 100 to 138 dBA
Jet plane heard at close range – 150 dBA
Any noise rating above 80 dBA produces physiological effects and any long term
exposures at much or above 90 or 100 decibels will cause permanent damage to a
Indian Institute of Technology Delhi 7
person’s hearing. An increase of 10 dBA is a doubling of loudness with respect to the
human ear [5].
Noise generally consists of many tones with varying rates of vibration or frequency. The
frequency expressed in cycles per sound or hertz (HZ) usually is in the range of 20 to
20,000 cycles per second. The ear is not very responsive to very low or very high tones
as it is to the tones of medium frequency. The dBA scale matches the response of the
ear, and is therefore well suited for evaluating noise as it relates to human beings [6].
The noisy industrial machine can be viewed as a sound generator. The noise generated,
generally, will be made up of sound waves which encompass the spectrum of 125 cycles
per second to 8,000 cycles per second with a certain frequency band being dominant.
The noise emitted is either direct airborne sound or noise generated by mechanical
vibrations setting up vibrations in sheet metal panels or large solid areas.
Sound waves decrease in length as the frequency increases or, more simply, the
wavelength is inversely proportional to the frequency. Generally, it is easier to control
noise in the higher frequency bands than the lower frequency bands since it is difficult
to absorb sound which is made up of long wave lengths.
2.1 Noise Control Principles It is necessary to treat at least one element in the noise system if the perceived level of
noise is to be reduced. By reducing the noise level at the source or along the path, the
noise level at the receiver point of interest is accordingly reduced. Treating the receiver
in such a way as to minimize the sensitivity to high noise levels is another approach to
the general noise problem. Each element of the noise system has associated with its
treatment advantages and disadvantages.
Treatment of the noise source is the most effective approach to a localized noise
problem. The noise source treatment is often, however, the most difficult to properly
implement. Treatment would be accomplished by addition of noise control materials or
the re-design of the noise source. Addition of noise control materials could hinder the
Indian Institute of Technology Delhi 8
process of the noise source in its primary functions. Redesign of the noise source may
be prohibitive based on the cost to redesign, develop and re-tool.
Treatment of the noise receiver is the least desirable approach since each receiver must
be treated individually. The addition of earplugs or earmuffs can encumber the receiver
to the extent of being impractical. Educating the receiver as to the source of the noise
and the purpose of the noise generating mechanism is another possibility. In any case
the degree of effectiveness of the treatment will vary since the range of subjective
reaction to noise varies from person to person.
Treatment of the noise path is conceptually the simplest and therefore the most common
approach to a localized noise problem. The approach is to place material in the path of
the noise (generally between the noise source and the noise receiver) so that the level of
noise at the receiver is reduced. The application of materials is often oversimplified,
however, leading to ineffective and/or inefficient use of materials. Also the air paths are
typically addressed while the structural paths are often overlooked. Finally, the design
of the treatments developed without consideration of assembly procedures can lead to
installation errors, which compromise the purpose of the treatment.
2.2 Approach to Analysis of Problems As pointed out earlier, the end recipient of noise is the human ear. An expedient
solution to a noise problem comes through the use of earplugs or other ear protection.
Legislation has taken the position that hearing protection of this nature will not be
tolerated if effective means for controlling noise at the source exists. The first step in
quieting a noisy environment is to clearly identify the problem.
An ideal starting point is to obtain the dBA levels emitted at various frequency bands.
This should also be done at several positions around the machinery. This can be done
with a simple sound level meter, however, with more sophisticated equipment, more
detailed data can be compiled regarding the frequency characteristics and nature of the
sound source.
Indian Institute of Technology Delhi 9
3. Analytical Survey of Noise Study in Textile Industry: Occupational Noise exposure has been linked with a range of negative health effects by
various researchers. The resulting injury of occupational hearing loss is also a well
recognized and global problem. To protect workers from hearing damage due to noise
exposure and other related health effects, a vast store of knowledge has been
accumulated till date about its nature, etiology and time course. There is still ignorance,
amongst majority of people working in industries in developing and third world
countries including India about ill effects of exposure to high values of noise.
Equivalent sound pressure level Leq has given in various sections of a plant with the
help of a digital sound level meter. The noise spectrum has been evaluated with the
help of 1/3 octave filter set. A cross sectional study involving 112 workers exposed to
different levels of occupational noise has been conducted [4].
Meliksah ERTEM et al [7]. shows the comparison of the mean hearing threshold levels
(dB) of control subjects with carpet mill and cotton textile factory workers. 4000 Hz
notch was plotted in carpet mill and cotton textile workers audiograms in the figure 1.
Fig. 1 Mean hearing levels (dB) at different frequencies.
The results of the study establish the fact that noise level in certain sections of the plants
i.e Loom Shed, Spinning, Ring Frame, TFO Area is more than the acceptable limit of 90
Indian Institute of Technology Delhi 10
dBA for 8 h exposure stipulated by OSHA. The noise level in other sections like
carding, blow room, combing etc., although is less than 90 dB(A), but is quite higher
than limits used for assessment of noise for community response. Octave band analysis
of the noise shows the presence of high sound level in 4,000 Hz frequency range, which
can be a major reason for causing occupational hearing loss. The results of the
interview questionnaire which included a number of parameters reveal the following; (i)
only 29% workers are aware about the effects of noise on health (ii) 28% workers are
using ear protectors (iii) the satisfaction with the working environment is related to
noise level, as workers exposed to comparatively less noise level report better
satisfaction (iv) 70% of the workers reported that high noise level causes speech
interference (v) 42% workers report the noise to be annoying. The study thus
demonstrates the presence of gross occupational noise exposure in both the plants and
the author believes that occupational noise exposure and the related effects in India is a
widespread problem.
The equivalent A-weighted sound pressure level LAeq has been calculated using the
equation:
The details of the Leq values of noise to which the workers are exposed in various work
areas in a textile mill is shown in the Table 2 and Table 3 below:
Indian Institute of Technology Delhi 11
Madbuli H. Noweir et al. [8] has shown, the dBA means of Leq, Max (SPL) and Min
(SPL) of the surveyed factories are in Table 4. The most used and possibly, the most
meaningful parameter, the Leq has varying degree of variance, ranging from 1.5 dBA2
(Hygienic Paper Products Co.) to 5.9 dBA2 (Nasr Printing Factory). Factories with
smaller variance of Leq could be treated with general noise control and reduction
techniques. However, factories with high variation may have hot spots which would
need individual noise control at the sources in addition to any general measures.
Table 4
Indian Institute of Technology Delhi 12
3.1 Spectrum Analysis
The octave band analysis of the noise in various work areas shows the presence of
high sound level in 4000 Hz. Figure 2 and 3 shows the octave band analysis of sound
spectrum in Ring Frame and loom shed respectively. The high level of sound present in
this frequency region can be a major reason for causing noise induced occupational
hearing loss.
Exposure to continuous and extensive noise at a level higher than 85 dBA may lead to
hearing loss. Continuous hearing loss differs from person to person with the level,
frequency and duration of the noise exposed [9.]. Negative effects of noise on human
beings are generally of a physiological and psychological nature. Hearing losses are the
most common effects among the physiological ones. It is possible to classify the effects
of noise on ears in three groups: acoustic trauma, temporary hearing losses and
permanent hearing loss [10]. Blood pressure increases, heart beat accelerations,
appearance of muscle reflexes, sleeping disorders may be considered among the other
physiological effects. The psychological effects of noise are more common compared to
the psychological ones and they can be seen in the forms of annoyance, stress, anger
and concentration disorders as well as difficulties in resting and perception [11, 12, 13].
3
Indian Institute of Technology Delhi 13
A great majority of people working in industry are exposed to noise. Therefore, in this
study, the effects of noise on human beings have been investigated with respect to the
level of noise they are exposed to [14] assembly procedures can lead to installation
errors, which compromise the purpose of the treatment.
3.2 Standards for noise abatement in industry
In the field of noise at the workplace, in spite of national regulations on noise at work in
force for many years, lots of people are still getting hearing losses due to machinery
noise in Europe as well as throughout the world. In order to progress, there was a need
for a policy enforcing noise reduction at source at the design stage and allowing market
forces to encourage less noisy machinery being put on the market. This was made
possible in Europe through a specific European regulation.
In parallel to the strong action on noise reduction at source at the design stage, a
standardization programme developed at the European and international levels on
workplace noise in particular on designing low-noise workplaces, designing means to
reduce noise on the propagation path and measuring their effectiveness.
3.3 The Machinery Directive
A major new approach directive is Directive 89/392/EC (first published in 1989,
subsequently amended and renumbered in 1998 as 98/37/EC), so-called “Machinery
Directive”.
Three types of standards, so-called type A, type B and type C standards, are elaborated
to accompany this directive. Type A is for standards covering basic safety concepts,
type B standards covering horizontal issues (e.g. noise emission measurement in
general) applicable to a large number of machinery and type C standards concerning
safety aspects (including hazards due to noise emission) of single types of machinery
[1].
Indian Institute of Technology Delhi 14
Figure 4 illustrates the essential role of standards in the current strategy for reducing
noise in industry.
Fig. 4 Global strategy for noise abatement in industry
Indian Institute of Technology Delhi 15
4. Structure of Textile Industry: A composite industry of Textile can be described as in the Structure of four types of
categories as Spinning mill, Weaving mill, Dyeing mill and Composite mill. In spinning
mill, only the yarns are produced using different type of twisting and pre processing
machines. In weaving mill, the yarn comes from the spinning section. First, the yarn
goes to the winding section to make the bigger packages to manufacturing the fabrics.
In weaving section, different types of looms are used for producing different categories
of fabrics according to the requirements of market demands. Similarly, in the dyeing
mill, they only make the fabric dyed and printed and finished.
In the composite mill, all three types of sections, which are mentioned above, are
involved. Some composite mill produce garments in further process.
The structure of a specialized composite mill has shown below:
Fig.5. Structure of a typical composite mill
4.1. Machineries in Spinning and Noise emission
In the spinning section, various machineries are used in the pre-spinning process as well
as twisting process. In pre-spinning process, generally Carding, Combing, Drawing and
Indian Institute of Technology Delhi 16
Draw twisting or Roving machines are used to produce twisted roves or slivers. For all
the operations, pneumatic pressure compressors are required. Those machines are
emitted noise in different levels. An US patent has reveals some features which takes
place to control noise in air jet spinning machinery [ 15].
After pre-processing, roves or slivers are used to manufacture yarns. In this section, as
per the end use, different types of spinning machines are used such as ring spinning,
rotor spinning DREF machines etc.
According to the speed of the machines, the emissions of sound levels are different in
different machineries. In the twisting zones, the rotor speed is maximum compare to
other spinning machines. The rotor speed is approximately 120000 rpm and the opening
roller speed is 5000-6000 rpm. Most of the sound emits due to the high speed of rotor.
Similarly, the speed of the spindle of Ring spinning approximately 20000 rpm and in
draw twisting machine, the speed of the spindle approximately 14000 rpm.
The approximate emissions of sound levels in spinning machineries are given in the
table 5.
Table 5
Name of the MachinesMax. Sound Level
(dBA)(apprx.)
Blow Room 82-84.8
Carding 86.2-89.2
Combing 84.5
Drawing 85
Roving 88-95.5
Ring Spinning 99.5-100.2
Rotor Spinning 102-104
DREF Spinning 89.9
Indian Institute of Technology Delhi 17
4.1.1. Existing mechanism of Noise control in Spinning
There are many kind of machines are existing in the spinning or any field of operations.
And the result that each operation has its own noise emission spectrum. Below, in the
figure, shown the noise spectrum for different process in textile sector
Fig. 6 Noise spectra of five processes 1. Staple fibre cutter, 2. Spinning, 3.
DrawTwisting, 4. Weaving, 5. Winding.
It is very difficult to control huge amount of noise in direct approach. Ear protector
could be a solution to prevent hazardous effect direct to the human physic as well as
psychology. But there are objection from hygiene, safety and comfort consideration.
The solution then is to reduce noise level in active approach. The active approach is to
overhauling and maintenance periodically that reduce the noise at source. A necessary
step to noise reduction at source is a detailed knowledge of the source mechanisms,
transmission path and noise radiating surface [2].
A typical diagram of a drawtwister has shown in the fig. 7.
Indian Institute of Technology Delhi 18
Fig. 7. Diagram of a drawtwister
From the fig. 8 we have seen that the loudest narrow band sound is produced from the
spindle and bobbin zones.
Fig 8. SPL of Drawbox and Bobbin
Indian Institute of Technology Delhi 19
A spindle diagram has shown in the fig. 9. The noise source can be control by the detail
study of the material and mounting mechanism of the spindle. Generally, spindle and
ball-bearing are produced by the metal, which produce more noise. It is possible to
change the material, metal to polymeric one.
Fig. 9. Spindle Use of Polyurethane gear, flexibly mounted gears, redesigned headstock and various
vibration isolation of parts, the noise contours change and the levels are reduced to meet
the recommended levels at the operator’s position. Some noise reduction techniques on
the draw-roll assembly has shown in (Fig 10). One approach used a polyurethane
bonded bush between the gear and the shaft. It reduced the overall noise level of one
shaft assembly by 7-8 dB. Another trial was made substituting a copper-manganese
alloy shaft for the steel shaft. The use of this material not only introduced its high
damping properties but also lowered the shaft critical below the running range. The
Indian Institute of Technology Delhi 20
result of using the copper-manganese shaft was to reduce the overall noise level by 4.5
dB.
Fig.10 Treated draw roll.
In the figure 11 octave band levels for the modified machine are compared to the
average drawtwist noise and a deafness risk criterion n.r.85. There is a reduction of
noise from 128 sones to 77 sones, i.e. a reduction in loudness od 40%. These noise
levels are for the modified machine running with full bobbins at spindle and drawroll
speeds higher by 11% and 20% respectively than the maximum production speeds
commonly used [16].
Indian Institute of Technology Delhi 21
Fig. 11 Octave band levels at centre of machine for modified drawtwist machine. 1.
Average drawtwist noise, 2. Modified machine noise, 3. n.r. 85 criterion
4.2. Machineries in Fabric manufacturing and Noise emission
As earlier discussion we have seen, various machineries are being used in fabric
manufacturing section, such as different type of Winding machine, Looms and knitting
machines. In winding zone, TFO (Two for one Twist), Doubling, Cheese winding, cone
winding, Precision winding machines are being used. And it is obvious that all the
machines are produced different levels of noise.
Similarly, different types of looms are used as per the requirement of fabric
construction. Now a day’s most preferable looms are shuttle less automatic looms.
Production of this type of loom is higher. It means the speed of the loom is higher and it
is understood that the loom produce higher level of noise.
The approximate emissions of sound levels in Fabric manufacturing are given in the
table 6.
Indian Institute of Technology Delhi 22
Table 6
Name of the MachinesMax. Sound Level
(dBA)(apprx.)
TFO 100
Doubling 92-95.5
Cheese Wing 93
Cone winding 92
Precision Winding 91-92
Shuttle Loom 99-100
Shuttle less Loom 100-105
Air jet Loom 110
Water jet Loom 96-99
The noise source of winding machine is almost similar to that of spinning machineries.
In case of TFO, the noise generates due to the revolution of the spindle in the spindle
chamber. The whole assembly of spindle and chamber vibrates due to it high revolution.
The maximum spindle speed is 16000 RPM [17] And the outcome of the result is high
amplitude narrowband noise [fig. 12]. Another major source of noise is gearing
arrangement in the gearbox.
Indian Institute of Technology Delhi 23
Fig. 12. TFO Spindle chamber arrangement.
Similarly, in Loom shed, there are many types of looms are use and it is obvious that all
different looms have different speed according to their production rate and frequency.
Due to the different sped and mechanism, the looms are produced different levels of
noise. Like, Air jet looms produce higher level of noise compare other looms (table 6).
In the figure 13 a typical Air jet loom has shown. Basically Air nozzle produces much
noise in this loom. Not only air nozzles, reed of the looms are produced high noise when
it strikes on the base plate of the reeds.
Indian Institute of Technology Delhi 24
Fig 13. Air jet Loom
In the Shuttle loom, most sound generates due to the movement of the shuttle. During
Weft insertion takes place through the Warp shed, shuttle caries the weft thread and it
strikes to the end of the shuttle path called sley end (fig 14.). Shuttle nose strikes on the
solid material and make noise in a high level.
In this occasion, there have a active control arrangement take place. At the end of the
shuttle path there have a buffer, which is made by rubber. The rubber buffer consume
kinetic energy of the shuttle and indirectly protects the noise.
Indian Institute of Technology Delhi 25
But there have no such type of arrangement to control noise in the reeds section.
According to the pattern of the fabrics, the reeds are acting up and down. Due to this
movement of the reeds a huge noise emits from the loom. When reeds moved down, it
strikes metallic parts inside the loom. Not only has this event, the friction between reeds
and slot of the reeds emitted noise in each movement. A typical reed has shown in the
figure 15.
Fig. 15. Reed
Fig. 14. Shuttle Loom and Shuttle
Indian Institute of Technology Delhi 26
4.2.1. Existing mechanism of Noise control in Fabric Manufacturing
An air jet loom makes cloth using compressed air to insert the weft into the warp. The
weft is inserted into the warp by the rocking motion of the sley, sword, reed, and
rocking shaft. By reducing the vibration produced by the rocking motion of this non-
balanced load, Toyota Industries has successfully improved the workplace environment
of its customers’ weaving mills. Some model of air jet loom was designed to optimize
the cross-sectional shape of the sley, the weight of which was reduced by 20% [18].
In addition, the material of the sword was changed and by perfecting its placement of
ribs using computer analysis, it was possible to lighten and harden the sword. By
attaching the balance weight to the rocking shaft, the load was reduced. As a result,
vibration was greatly decreased by reducing the dynamic load on the floor by 20%.
As earlier discussion, a conventional loom has changed very little since the industrial
revolution[19] Much of the noise arises from the impact and general clatter of the
shuttles, picking arms and harness. The spectrum is mainly high frequency and the
sources are difficult to eliminate, mainly because impact is inherent in the process.
Noise control of shuttle and picking arm noise in the jute industry [20] can reduced a
loom by up to 10 dB. This can has been achieved by replacing metallic picking points
and picking cones with polyethylene parts [21]. Nylon driving pinions and nylon bushes
have been used in lieu of cast iron. Figure 16 has shown the different sound level in
Shuttle and water jet looms [2]
Indian Institute of Technology Delhi 27
Fig. 16. Noise comparison, 1.Shuttle loom (205ppm) 2.Water Jet Loom (400ppm)
5. Some ideas to control noise in textile machinery: It has already been discussed that controlling noise is challenging job in textile
machinery. There have so many barriers to control noise or to protect health hazards of
workers.
In this text we will discuss the probable controlling system of induced noise from textile
machineries.
Noise control in textile machinery can be classified in two broad sections. One is active
and another is passive control. Probable noise control system in textile machineries has
shown in the flow chart in figure 17.
Indian Institute of Technology Delhi 28
Fig. 17. Control Flow chart
5.1. Active Noise Control
According to the flow chart, it is possible to control of noise that emits from the
machineries by two ways. In active system, directly we can control the noise bye
controlling the machine itself. Generally the noise generates from the machine due to its
unwanted vibrations in various levels of frequencies and material to material friction
[22].
If we are able to control that unwanted vibration friction as well, to some extent we can
control the noise directly. Machine vibration can be controlled by three ways; first, we
can control by proper balancing the machines,
There are two main types of balancing machines, hard-bearing and soft-bearing. The
difference between them, however, is in the suspension and not the bearings. In a hard-
Indian Institute of Technology Delhi 29
bearing machine, balancing is done at a frequency lower than the resonance frequency
[Figure 18] of the suspension [23].
Fig. 18. Resonance frequency
In a soft-bearing machine, balancing is done at a frequency higher than the resonance
frequency of the suspension. Both types of machines have various advantages and
disadvantages. A hard-bearing machine is generally more flexible and can handle pieces
with greatly varying weights, because hard-bearing machines are measuring centrifugal
forces and require only a one-time calibration. Only five geometric dimensions need to
be fed into the measuring unit and the machine is ready for use. Therefore, it works very
well for low- and middle-size volume production and in repair workshops. A soft-
bearing machine is not so flexible in respect of amount of rotor weight to be balanced.
The preparation of a soft-bearing machine for individual rotor types is more time
Indian Institute of Technology Delhi 30
consuming, because it needs to be calibrated for every individual part. It is very suitable
for high-production volume and high-precision balancing tasks. Hard- and soft-bearing
machines can be automated to remove weight automatically, such as by drilling or
milling, but hard-bearing machines are more robust. Both machine principles can be
integrated into a production line and loaded by a robot arm or gantry, requiring very
little human control. Soft-bearing machines are also generally more expensive because
of the higher complexity in the design and manufacturing.
Secondly, proper material selection for vibrating parts and in which parts material to
material frictions takes place; as an example metallic gear arrangements. For our
experience, it is visible that metallic gear to metallic gear arrangement produces more
noise compare to polymeric gear. Although, there have many advantages as well as
disadvantages for polymeric gear arrangements. However, in account of control of
noise, polymeric gears are more suitable rather than metallic one. Generally
polyurethane, polyester, polyamide polymers are used for this purpose. It is known that
where the rotational movements takes place in the machine parts, the vibration occurs
more, as an example spindles, gears, crank shaft etc. those parts can be replaced by
polymeric materials instead of metallic one.
On the other hand, noise can be reduced by keeping control the noise source. That
means, overhauling is important to reduce noise. Periodically lubrication is required in
the zone of gears to gear arrangement, ball-bearing and other rotational parts. For all the
machines overhauling duration and indication of lubrication is mentioned [24].
5.2. Passive Noise Control
The passive noise control system is nothing but the control after emission of noise.
Emitted noise can be controlled by two ways; one is to making casing around the noise
source and another is hearing protection. Many cases in textile machineries casing
arrangement is difficult because of the production front. Generally, the production front
Indian Institute of Technology Delhi 31
in textile machineries is kept open to doffing conveniently after preparation of final
products for spinning as well as weaving. It is easy to casing the gearbox effectively.
Casing arrangement will be discussed as the following ways:
Casing arrangement can be prepared by three ways; using damping material, barrier
materials and absorptive materials. In both the cases the aim is to control vibration.
Details discussions about those materials are given below.
5.2.1. Primary function of Damping materials
A damping material is used to reduce the vibration level in a vibrating system. The
terms damping and deadening have long been used to describe the effects of general
noise control measures. The topic taken up here is vibration damping as opposed to
sound absorption, sound transmission loss or vibration isolation [25].
5.2.1.1Definition
Damping is the reduction of kinetic energy present in a system through transformation
into another form of energy. The efficiency of damping present is evaluated by
determining the system’s loss factor. The dimensionless loss factor (η) is defined as:
UW
ff
TD
Qd
n
n
ππη
221
0
0 =∆
===
Where,
Q = System damping factor
D0 = Total energy dissipated in the system as the result of damping for one cycle
T0 = Total vibration energy of the system
fn = Undampted resonant frequency (Hz)
∆fn = Half power bandwidth (Hz)
Wd = Energy dissipated from the system
U = Max. energy stored in the system
Indian Institute of Technology Delhi 32
Half power bandwidth is shown in the figure 19.
Fig. 19. Half power bandwidth
5.2.1.2 How does the damping material works
The damping materials generally reduce the vibration amplitude by generating heat
energy. Viscoelastic dampers are adhered to the vibration surface. This materials
generates heat when it undergoes deformation. By optimizing a material’s stiffness and
internal losses, the damping performance can be optimized.
It should be noted that the addition of damping material changes the stiffness to mass
ratio of the system and accordingly, the resonances of system are affected.
The damping performance of the viscoelastic material can be improved by spacing the
material from the sheet metal. These applications take advantage of the extensional
deformation of the damping material. By placing the viscoelastic material between two
relatively inelastic materials, the viscoelastic material experiences shear deformation
(figure 20). This also results in improved damping performance. Because of the
different mechanisms of inducing deformation in the damping material, a material that
performs well as a free layer may not perform as well as a constrained layer and vice
versa.
Indian Institute of Technology Delhi 33
Fig. 20. Different damping applications
5.2.2. Function of Barrier materials
A barrier material also reduces the amplitude of sound waves propagating in a certain
direction. The barrier material interferes with sound waves as they propagate away from
the sound source. The portion of the sound energy which continues to propagate along
the original path is then of significantly lower amplitude than the original wave.
In the figure 21, it has been that how the barrier material works.
Fig. 21. Noise incident on a barrier material
Indian Institute of Technology Delhi 34
A barrier material, which reduces sound energy as the sound wave is transmitted
through the material. The measure of a material’s effectiveness as a transmission loss as
earlier discussion. Transmission loss is the fraction of energy dissipated as a result of
sound being transmitted through the material. Transmission loss is measured in decibels
as:
TL = 10log10 5.2.2.1 How does the barrier material works
As the sound wave interacts with the barrier material, the mass of the material opposes
the wave motion of the air molecules, thus causing a reflection of some portion of the
sound energy. A fraction of the energy is absorbed and dissipated as heat due to the
internal damping of the material. The remaining energy is converted to sound energy on
the side of the barrier material opposite the impinging sound wave.
The transmission loss (TL) of a material is principally determined by the mass of the
material. At low frequencies the material’s stiffness and mass determine the TL. At high
frequencies the material stiffness, damping and the mass determine the TL. For
frequencies where the TL is essentially mass controlled, the TL by 6 dB for most
frequencies.
The effectiveness of the barrier is dependent on its ability to sufficiently interfere with
the sound wave. The barrier must have effective dimensions much greater than the
wavelength of the sound to have significant influence on the sound level.
The material should be impervious with respect to air. Holes in the barrier affects its
performance. They significantly reduce the effective dimensions of the barrier and they
allow for air pressure communication directly through the barrier material. Thus
reduction the potential acoustic value of the barrier.
Incident sound intensity (Ii) Transmitted sound intensity (It)
Indian Institute of Technology Delhi 35
5.2.3. Function of Absorption materials
Sound absorption materials reduce the acoustic energy of a sound wave as the wave
passes through the material. They are commonly used to often the acoustic environment
of an enclosed volume by reducing the amplitude of reflected sound waves. The benefit
of the absorption material is multiplied by applying the material to a reflective surface
since the sound is made to pass through the absorption material more than once.
In the figure 22 a absorption material has shown.
Fig.22. Noise incident on an absorption material
For a sound absorption material applied to an acoustically reflective surface, sound
energy incident (Ii) on the material is partially absorbed by the material (Ia) and the
remaining sound energy is reflected (Ir). The sound absorption capability of a material is
expressed in terms of the sound absorption coefficient; α the sound absorption
coefficient is defined as:
α =
The absorption coefficient can have values between 0 and 1.
Acoustic energy absorbed by a surface (Ia=Ii-Ir) Acoustic energy incident on a surface (Ii)
Indian Institute of Technology Delhi 36
5.2.3.1. How does the absorption material works
In order for a material to have good sound absorption performance, the material has to
be a porous or fibrous one. Sound waves propagate into the material and loss energy by
viscous dissipation. Sound waves inside the material also caused the fibres to rub
against each other, thereby producing heat energy and dissipation sound energy.
The absorption characteristics of a material are a function of frequency. Performance
generally increases with an increase in frequency. As a rule of thumb, the material
thickness should be a quarter of the wavelength (λ) of the sound wave to be effective.
Therefore, material thickness is an important determinant of absorption performance. It
has shown in the figure 23.
Fig.23. Random incidence sound absorption for
Polyurethane foam of various thicknesses.
Indian Institute of Technology Delhi 37
So, from the above discussion, it is proved that the noise induce from textile
machineries can be controlled by designing some special features in a particular place of
a specified noisy part.
Some cases when machines are not in controlled for emission of noise, the workers of
supervising authority can have ear protector. Using ear protector, to some extent, noise
hazards can be controlled for human health.
Indian Institute of Technology Delhi 38
6. Conclusion: For the textile, industry control of noise emission from the textile machineries is a
challenging job. Some of the cases noise control has been taking place in few industries.
Most of the textile industry in India, they are unable to implement the noise control
system. To understand for noise control it is experienced that the controlling systems
not only reduce the noise at source to acceptable levels, but also reduces the energy
consumption in to some extent and at the same time leads to a better design of the
machines too. For example, polymeric gear-gear arrangement or polymeric spindle
consumes less energy compare to metallic one for the same r.p.m., it means that less
energy consumption can leads to give higher speed as well as higher production.
In this occasion, we have seen that it is possible to reduce emission of noise as well as
control of noise when human health is concerned. There have number of possible
procedure to control noise. We have also seen that the control can be achieved by two
ways, such as Active and Passive control. There have different features for those control
system.
For active control, our aim is to reduce vibration and friction in situ of the noise parts by
replacing materials as well as parts configurations. In this case, rotational metallic parts
can be replaced by polymeric where noise comes out due to friction.
For passive control, we want to reduce the noise level which has already been emitted
from the source. There are some procedures to control the noise. The noise source can
be covered fully of the cover can be treated by different process such as using damping,
barrier and absorption materials. Some cases ear protectors are used to prevent noise
hazards.
Indian Institute of Technology Delhi 39
7. References:
1. Jean Jacque, Noise And Standardization, Focussing On Machinery And Workplace
Domains, Institut National de Recherche et de Sécurité, I.N.R.S. Standardization Unit
CEN Consultant for Noise, 30 rue Olivier Noyer, 75680 Paris, Cedex 14, France
2. R. Crawford, Noise Control On Textile Machinery, Phil. Trans. R. Soc. Lond. A. 1968
347-367 263
3. L.E.Kinsler, A R. Frey, A B. Coppens, J V. Sanders, Fundamentals of Acoustics, pp377
4. Raman Bedi, Evaluation of Occupational Environment in Two Textile Plants in
Northan India with specific reference to noise, Industrial Health 2006, 44, 112-116
5. Dr. D.P.Raychaudhuri Advance Acoustics, , University of Kalyani, pp 283
6. Acoustical Solutions, Inc. 2852 East Parham Rd., Richmond, VA 23228 Ph: 800-782-
5742 fax: 804-346-8808, www.acousticalsolutions.com
7. Meliksah Ertem, Ersen Ilçin, Faruk Meriç, Noise Induced Hearing Loss Among Cotton
Textile and Carpet Mill Workers, Tr. J. of Medical Sciences 28 (1998) 561-565 ©
TÜBITAK
8. Madbuli H. Noweir And A. T. M. Jamil, Noise Pollution In Textile, Printing And
Publishing Industries In Saudi Arabia, Environmental Monitoring and Assessment 83:
103–111, 2003. © 2003 Kluwer Academic Publishers. Printed in the Netherlands
9. USEPA (United States Environmental Protection Agency). Information on levels of
environmental noise requisite to protect public health and welfare with adequate margin
of safety, (EPA/ONAC Rep. No. 550/9-74-004); 1974
10. Melamed, S., Fried, Y., Froom, P. The interactive effect of chronic exposure to noise
and job complexity on changes in blood pressure and job satisfaction: A longitudinal
study of industrial employees, Journal of Occupational Health Psychology, 6, 182, 2001
11. Cheung, C. K. Organizational influence on working people’s occupational noise
protection in Hong Kong. Journal of Safety Research, 35, 465, 2004
12. Öhrström, E. Sleep disturbance psycho-social and medical symptoms a pilot survey
among person exposed to high levels of road traffic noise, Journal of Sound and
Vibration, 133, 117; 1989
Indian Institute of Technology Delhi 40
13. Finegold L. S., Harris C. S., Gierke Von. H. E. Community annoyance and sleep
disturbance; Updated criteria for assessing the impact of general transportation noise on
people. Noise Control Eng. J. 42 (1) Jan.-Feb. 1994
14. E. Atmaca1, I. Peker1, A. Altin, Industrial Noise and Its Effects on Humans, Polish
Journal of Environmental Studies Vol. 14, No 6 (2005), 721-726
15. B.D. Lassiter et al., Noise control system for textile machinery , US patent, no.
4586323, date may 6,1986
16. W. Klein, A practical guide to Combing and Drawing, Volume 3, pp. 42-56
17. www.himsonoriginal.com
18. Tatsuo Matsuura, Environmental Protection Activities of the Textile Machinery
Division Division Manager & Managing Director, Textile Machinery Division
19. Sadao Aso, Rikuhiro Kinoshita, Heihachi Uematsu and Kiyohumi Sasaki, Members,
TMSJ, Noise Generated by a Power Loom, Based on Journal of the Textile Machinery
Society of Japan, Transactions, 18, T13-19 (1965)
20. Stott , A. 1965, Reducing noise in weaving sheds, Textile Manufacturing Machinery
21. Adanur, S. Handbook of weaving, pp. 175-223
22. K sugita et al., Device for noise attenuation of Weaving Machine, US patent, patent no.
5271062, date Dec. 14, 1993
23. Adolf Lingener: Auswuchten. Theorie und Praxis. Verlag Technik, Berlin und
München 1992, ISBN 3-341-00927-2
24. Talukdar, M.K. et al., Weaving, Machines, Mechanisms, Management, Appendix Viii-
Xiii, pp. 590-598
25. Application of Noise control and heat insulation materials, American Acoustical
products, 6 october Hill road, Massachusetts 01746