No. Products Model No. Pagef02.s.alicdn.com/kf/UT8XJDDXaldXXc_PVbXJ.pdf• 5.1 channel Dolby Digital (AC-3) encoding support • 7.1 channel SPDIF audio optical input (pass through)

DATASHEETS

No. Products Model No. Page

1. DSNG Encoder DMP-9724SNG 2

2. MPEG-2/4 AVC HD Encoder (4:2:2) DME-9724HM 4

3. MPEG-2/4 AVC HD Encoder (4:2:2) DME-9724H 6



6. Multi 8 Channel SD Encoder DME-8624S8 12

7. MPEG-2/4 AVC SD Encoder DME-8624S 14

8. Integrated Receiver / Decoder DMD-9724IRD 16

9. MPEG Decoder DMD-9724D 18

10. MPEG HD Mediaplex (4:2:2) DMP-9724M 20



13. ISDB-T Multiplexer DMX-1908ST 26

14. DVB-T2 Gateway DMX-1908T2 28

15. Management System NMS 30

16. 8-VSB Modulator DVM-1903ML 31

17. QAM Modulator DQM-1903ML 32

18. IPASI Converter DIC-500 33

19. Multi Digital Scaler DSR-1000 34

20. HDMI to SDI Scaler DSR-500 35

21. Multi Media Converter MMC-1000 36

22. Media Converters ATS-500 37

23. Media Converters STH-500 / HTS-500 38

#40-12 Teheran-ro 38-gil, Gangnam-gu, Seoul, Korea 135-920Phone : +82 2 6005 9115Fax : +82 2 3453 8338E-mail : [email protected]

Head Office / Laboratory www.castwin.com

Introduction

DMP-9724SNG designed for Teleports, Digital Satellite News Gathering Vehicles, and it is operating on either the C, Ku or Ka-bands.As a representative model of CASTWIN, it is the best performing and fully programmed high-end encoding. Also, it has DVB-S/S2 modulation with the highest video quality and the lowest latency.

Encoding & DVB-S/S2 Modulation

Latency 150ms

Chroma Format 4:2:0 4:2:2

Resolutions up to 1080p

L-Band or IF output

• Component, Composite, HDMI, HD/SD-SDI video inputs• Ultra low latency as 150ms• Up to 1080p supported• Support 4:2:0(8bit), 4:2:2(10bit)• Digital, Analog and SDI embedded audio(8channel) inputs• 5.1 channel Dolby Digital (AC-3) encoding support • 7.1 channel SPDIF audio optical input (pass through)• Additional 1xASI input for supporting of insertion of externally generated PSIP into the transport stream

• Provides internally generated PSI, PSIP, SI• Control of Frame rate• Selectable MPEG-2 HD or H.264 HD real-time video encoding• Simultaneous outputting of 2xTransport stream (ASI) with UDP/IP or RTP/IP transport stream.

• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC, HE-AAC audio encoding

• Supports EIA-708 Closed caption insertion via HD SDI(SMPTE 334).

• Supports internally generated TVCT, CVCT, SDT, NIT• Excellent IP converter integrated performance

-Much lower latency & stable IP output• Control and monitoring via web browser, front panel, or SNMP• 4 channel AES/EBU Digital Audio • 4 stereo (8channel) Analog input with D-sub type • Integrated Advanced Scaler function

- Control of Frame rate, Image enhance- Phase Noise, Correction of Color, Control of Gamma

• L-Band Output 950 ~2150 MHz or IF Output 50 ~ 180 MHz• DVB-S/S2 Modulation• BISS mode-1 and BISS mode-E support• Designed for Teleports, Digital Satellite News Gathering Vehicles• Operating on either the C, Ku or Ka-bands• Symbol Rate: 1 Mbaud ~ 68 Mbaud

Feature

• Providing your viewers with the best performance compression and flawless picture quality

• Wide use in many projects with high compatibility supporting various formats

• Best choice for broadcasting of racing, sports via real time encoding with ultra low latency, at 150ms

• Reduce the cost of transmission as supporting wide range of bit-rate control and advanced video coding techniques

• Able to Secure space with compact size for installing

Competitiveness

DSNG Encoder

DMP-9724SNG

Options

• IP Streaming output

2

DSNG Encoder

DMP-9724SNG

DSNG Encoder www.castwin.com Digital Products MPEG Encoders

Specifications

Configuration

ITEM CHARACTER

Video Input

Analog Input Composite, ComponentLevel 1 Vp-p

Digital Input HDMI, HD-SDILevel 1000 mVp-p (HDMI) 800mVp-p (HD-SDI)

Resolutions 480i29.97, 576i25, 720p50/59.94,1080i25/29.97, 1080p25/29.97

SD Aspect Ratio 4:3, 16:9

Audio Input

AnalogInput 4 StereoFreq. Range 20 Hz ~ 20 KHzImpedance 600 Ω Connector D-SUB 15pin x 2

Digital Input 4 x AES-EBU, Embedded SDI/HDMI (4 Stereo 8 Channel)Sampling Rate 32, 44.1 and 48 KHzConnector BNC (75Ω) / HDMI-19PIN

Optical Input SPDIF(7.1 Channel) pass through

Video Encoder

Encoding MPEG-2 HP@HL, MP@HL , [email protected] HP@L4, MP@L3

Encoding Rate MPEG-2 : 0.6~50 Mbps , H.264 : 0.6~50 MbpsChroma Depth 4:2:0(8bit), 4:2:2(10bit)PSNR 38 dBBit Rate Mode CBR,VBRLatency 150 ms~

Audio Encoder

Input Sampling Rate 32, 44.1, 48 KHzOutput sampling Rate 48 KHz

EncodingMPEG-1 Layer II (2ch) AC-3 (2ch) AC-3 Pro (2ch, 5.1ch)AAC LC (2ch, 5.1ch) HE-AAC v1 (5.1ch) HE-AAC v2 (2ch)

Audio Mix 4 Stereo (8channel) or 5.1chBit Rate AC-3 128, 192, 256, 384 KHz

AC-3 Pro 96, 112, 128, 160, 192, 224, 256, 320, 384 KHzMPEG1 64, 96, 112, 128, 160, 192, 224, 256, 320, 384 KHz AAC LC 32,48,56,64,80,96,112, 128,160,192, 224, 256, 320,384 KHzHE AAC v2 32, 48, 56, 64, 80, 96 KHzAC-3 Pro 5.1 224, 256, 320, 384, 448, 576, 640 KHzAAC LC 5.1 96, 112, 128, 160, 192, 224, 256, 320, 384 KHzHE AAC v1 5.1 96, 112, 128, 160, 192, 224, 256 KHz

Delay -100 ~ 400 ms

TS Input

Transport Stream DVB-ASI 1port

DVB-S

Mode code QPSK, 8PSK, 16QAM Connector BNC (75 Ω) Roll-Off 0.05 ~ 0.35 Packet Format 188 Byte BISS Mode (1,E Injected, E Buried) Output Level 800 mVp-p Symbol Rate 1 ~ 68Mbauds

TS Output

Transport Stream ASI 2portConnector BNC (75 Ω)

DVB-S2

Mode code QPSK, 8PSK, 16APSK, 32APSK

TS Bit RateMPEG-2 : 2.5~55 Mbps , Roll-Off 0.05 ~ 0.35 H.264 : 2.5~55 Mbps BISS Mode (1,E Injected, E Buried)

Packet Format 188 Byte Symbol Rate 1 ~ 68Mbauds

IP TS Output(Option)

Output 1 port Pilot Insertion

Connector RJ-45 Operating Mode CCM only Ethernet type 10/100/1000 Base-T Frame Type Normal / Short Stream Protocol UDP/IP, RTP/IPBroadcasting Multicast, Unicast

RF Option

Reverse Spectrum

TS Bit rate MPEG-2 : 2.5~55 Mbps , Tilt Correction -0.040 ~ 0.040 dB/MHz H.264 : 2.5~55 Mbps Carrier Modulator

Ethernet

Connector RJ-45 Out Level -35.00 ~+5.00 dBm

Interface Type 10/100 Base-T L-Band 950 ~ 2150 MHz

Protocols SNMP IF 50/180MHz

General

Power Requirements AC 90~230 V, 50/60 HzPower Consumption Max. 100 WWeight 4 KgOperating Temperature -10 ~ 50 Dimensions (W x H x D) 482 x 44 x 483 mm

3



Introduction

As a representative Encoder of CASTWIN, it is a newly released product which is the best performing and fully programmed high-end encoding with wonderful video quality and the lowest latency. DME-9724HM let you feel very much reality as if you are the part of video. Also, it enables to transmit more video channels and audio channels at the available bandwidth.

High-End Encoding

Latency 150ms



• Component, Composite, HDMI, HD/SD-SDI video inputs• Ultra low latency as 150ms• Up to 1080p supported• Support 4:2:0(8 bit), 4:2:2(10 bit)• Digital, Analog and SDI embedded audio(8channel) inputs.• 5.1 channel Dolby Digital (AC-3) encoding support • 7.1 channel SPDIF audio optical input(pass through)• Additional 1xASI input for supporting of insertion of externally generated PSIP into the transport stream

• Provides internally generated PSI, PSIP, SI• Control of Frame rate• Selectable MPEG-2 HD or H.264 HD real-time video encoding• Simultaneous outputting of 2xTransport stream (ASI) with UDP/IP or RTP/IP transport stream.

• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC, HE-AAC audio encoding

• Supports EIA-708 Closed caption insertion via HD SDI(SMPTE 334)

• Supports internally generated TVCT, CVCT, SDT, NIT• Excellent IP converter integrated performance

-Much lower latency & stable IP output• Control and monitoring via web browser, front panel, or SNMP• 4 channel AES/EBU Digital Audio • 4 stereo(8channels) analog input with D-sub type • Integrated Advanced Scaler function

- Control of Frame rate, Image enhance- Phase Noise, Correction of Color, Control of Gamma

Feature



• Best choice for broadcasting of racing, sports via real time encoding with ultra low latency, at 150ms

• Reduce the cost of transmission as supporting wide range of bit-rate control and advanced video coding techniques


Competitiveness

MPEG-2/4 AVC HD Encoder

DME-9724HM

4


DME-9724HM

MPEG-2/4 AVC HD Encoder www.castwin.com Digital Products MPEG Encoders

Specifications

ITEM CHARACTER

Video Input

Analog Input Composite, Component

Level 1 Vp-p

Digital Input HDMI, HD-SDILevel 1000 mVp-p (HDMI) 800mVp-p (HD-SDI)

Resolutions 480i29.97, 576i25, 720p50/59.94,

1080i25/29.97, 1080p25/29.97


Audio Input

AnalogInput 4 StereoFreq. Range 20 Hz ~ 20 KHzImpedance 600 ΩConnector D-SUB 15pin x 2

DigitalInput 4 x AES-EBU, Embedded SDI/HDMI (4 Stereo 8 Channel)Sampling Rate 32, 44.1 and 48 KHzConnector BNC (75Ω) / HDMI-19PIN

Optical Input SPDIF(7.1 Channel) pass through

Video Encoder

Encoding MPEG-2 HP@HL, MP@HL , MP@ML

H.264 HP@L4, MP@L3Encoding Rate MPEG-2 : 0.6~50 Mbps , H.264 : 0.6~50 MbpsChroma Format 4:2:0, 4:2:2 (8 bit / 10 bit)PSNR 38 dBBit Rate Mode CBR,VBRLatency 150 ms~

Audio Encoder

Input Sampling Rate 32, 44.1, 48 KHz

Output sampling Rate 48 KHz

EncodingMPEG-1 Layer II (2ch) AC-3 (2ch) AC-3 Pro (2ch, 5.1ch)AAC LC (2ch, 5.1ch) HE-AAC v1 (5.1ch) HE-AAC v2 (2ch)

Audio Mix 4 Stereo (8ch) or 5.1chBit Rate AC-3 128, 192, 256, 384 KHz

AC-3 Pro 96, 112, 128, 160, 192, 224, 256, 320, 384 KHzMPEG1 64, 96, 112, 128, 160, 192, 224, 256, 320, 384 KHzAAC LC 32,48,56,64,80,96,112, 128,160,192, 224, 256, 320,384 KHzHE AAC v2 32, 48, 56, 64, 80, 96 KHzAC-3 Pro 5.1 224, 256, 320, 384, 448, 576, 640 KHzAAC LC 5.1 96, 112, 128, 160, 192, 224, 256, 320, 384 KHzHE AAC v1 5.1 96, 112, 128, 160, 192, 224, 256 KHz

Delay -100 ~ 400 ms

TS Input

Transport Stream DVB-ASI 1portConnector BNC (75 Ω)Packet Format 188 ByteOutput Level 800 mVp-p

TS Output

Transport Stream ASI 2portConnector BNC (75 Ω)TS Bit Rate MPEG-2 : 2.5~55 Mbps , H.264 : 2.5~55 MbpsPacket Format 188 Byte

IP TS Output

Output 1 portConnector RJ-45Ethernet type 10/100/1000 Base-TStream Protocol UDP/IP, RTP/IPBroadcasting Multicast, Unicast

TS Bit rate MPEG-2 : 2.5~55 Mbps , H.264 : 2.5~55 Mbps

EthernetConnector RJ-45Interface Type 10/100 Base-TProtocols SNMP

General

Power Requirements AC 90~230 V, 50/60 HzPower Consumption Max. 100 WWeight 4 KgOperating Temperature -10 ~ 50 Dimensions (W x H x D) 482 x 44 x 483 mm

Configuration

5



Introduction

As a representative Encoder of CASTWIN, it is a newly released product which is the best performing and fully programmed high-end encoding with wonderful video quality and the lowest latency. DME-9724H let you feel very much reality as if you are the part of video. Also, it enables to transmit more video channels and audio channels at the available bandwidth.

High-End Encoding

Latency 150ms



• Component, Composite, HDMI, HD/SD-SDI video inputs• Ultra low latency as 150ms• Up to 1080p supported• Support 4:2:0(8 bit), 4:2:2(10 bit)• Digital, Analog and SDI embedded audio(8channel) inputs.• 5.1 channel Dolby Digital (AC-3) encoding support • 7.1 channel SPDIF audio optical input(pass through).• Additional 1xASI input for supporting of insertion of externally generated PSIP into the transport stream.

• Provides internally generated PSI and PSIP.• Various functions with integrated Advanced Scaler.• Control of Frame rate, Image enhance, Phase Noise, Correction of Color, Control of Gamma

• Selectable MPEG-2 HD or H.264 HD real-time video encoding.

• Simultaneous outputting of 2xTransport stream (ASI) with UDP/IP or RTP/IP transport stream.

• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC, HE-AAC audio encoding.


Feature



• Best choice for broadcasting of racing, sports via real time encoding with ultra low latency as 150ms

• Reduce the cost of transmission as supporting wide range of bit-rate control and advanced video coding techniques.


Competitiveness


DME-9724H

6



Specification

Video Input

Analog Input Component , Composite

Level 1 Vp-p

Digital Input HDMI , SDI

Level 1000 mVp-p (HDMI) 800mVp-p (SDI)

Resolutions480i29.97, 576i25, 720p50/59.94

1080i25/29.97

1080p25/29.97


Audio Input

Analog Input 1 stereo

Freq. Range 20Hz ~ 20KHz

Impedance 600 Ω

Connector Mini XLR

Digital Input AES-EBU, Embedded SDI/HDMI(8Ch)

Sampling Rate 32, 44.1, 48 KHz

Connector BNC (75Ω) / HDMI-19PIN

Optical Input SPDIF(7.1 Channel) (pass through).

Video Encoder


H.264 HP@L4, MP@L3

Encoding Rate MPEG-2 : 2~50 Mbps

H.264 : 0.6~50 Mbps

Chroma Format 4:2:0(8bit), 4:2:2 (10bit)

PSNR 38dB

Bit Rate Mode CBR,VBR

Latency 150ms~

Audio Encoder

Sampling Rate 32, 44.1, 48KHz

Dolby Digital® AC-3(7.1CH) 128,192,256,384 Kbps

MPEG-1 Layer II 192,224,256,320,384 Kbps

MPEG-4 AAC-LC 32~384 Kbps

MPEG-4 HE-AAC v1 32~192 Kbps


TS Input

Transport Stream ASI 1 Port

Connector BNC(75Ω)

Packet Format 188 Byte

Input Level 800mVp-p

TS Output

Transport Stream ASI 2 port

Connector BNC(75Ω)

TS Bit Rate MPEG-2 : 2.5~55 Mbps

H.264: 2.5~55 Mbps

Packet Format 188, 204 Byte

IP TS Output

Output 1 Port

Connector RJ-45

Ethernet type 10/100 Base-T

Format UDP/IP, RTP/IP

IP Address Format Multicast, Unicast

TS Bit rate MPEG-2 : 2.5~55 Mbps

H.264: 2.5~55 Mbps

TS Packet Rate 188,204 Byte

Ethernet

Connector RJ-45

Interface Type 10/100Base-T

Protocols SNMP

General

Power Requirements AC 90~230V, 50/60Hz

Power Consumption Max. 100W

Weight 4 kg

Operating Temperature -10~50°C

Dimension(W x H x D) 482 x 44 x 383 mm

Configuration


DME-9724H

7



Introduction Feature

Competitiveness


DME-9624H

CASTWIN’s High-definition encoder offering highest video quality with low latency. It shows excellent performance for inputting signal (Analog & Digital) to output as transport stream signal after compressing and encoding for suitable digital transmission with various supportedformats. Moreover, it supports both MPEG-2 and H.264 so that it makes operators select the format as they want.

• Component, Composite, HDMI, HD/SD-SDI video inputs.• Low latency as 800ms• Digital, Analog and SDI embedded audio(4ch) inputs.• 5.1 channel SPDIF audio optical input(pass through)• Additional 1xASI input for supporting of insertion of externallyGenerated PSIP into the transport stream.

• Video input Auto detection function.• Selectable MPEG-2 or H.264 HD/SD real-time videoencoding.

• Various functions with integrated Advanced Scaler.• Control of Frame rate, Image enhance, Phase Noise, Correction of Color, Control of Gamma

• Simultaneous outputting of 2xTransport stream (ASI) withUDP/IP or RTP/IP transport stream.

• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC, HE-AAC audioencoding.

• Excellent option for operators who competitively pursue the best performing encoding device with high resolution up to 1080p

• Good option for Real time encoding with low latency • Low cost and High performance • Able to secure space with compact and light weight design

• Make operators pay for less labor fee as offering quick and easy setup

Latency 800ms

Chroma Format 4:2:0 (8bit)


Options

DME-9624HMExcellent IP converter integrated- Much lower latency- More stable IP output

8



Specification

Video Input


Level 1 Vp-p



Resolutions 480i29.97/30, 576i25, 720p50/59.94/60, 1080i25/29.97/30, 1080p25/29.97/30


Audio Input

Analog Input 1 Stereo(2channel)


Impedance 600 Ω

Connector Mini XLR

Digital Input AES-EBU, Embedded SDI/HDMI



Optical Input SPDIF(5.1 Channel) (pass through).

Video Encoder


H.264 HP@L4 , MP@L3

Encoding Rate MPEG-2 : 2~17.2 Mbps

H.264 : 0.5~17.2 Mbps

Chroma Format 4:2:0 (8bit)

PSNR 36dB

Bit Rate Mode CBR, VBR

Latency 800ms~

Audio Encoder







TS Input


Connector BNC(75Ω)



TS Output


Connector BNC(75Ω)

TS Bitrate MPEG-2 : 3.4~19 Mbps

H.264 : 2.5~19 Mbps


IP TS Output

Output 1 Port

Connector RJ-45




TS Bitrate MPEG-2 : 3.4~19 Mbps

H.264 : 2.5~19 Mbps

TS Packet Rate 188, 204 Byte

Ethernet

Connector RJ-45


Protocols SNMP

General



Weight 4kg



Configuration


DME-9624H

9



Introduction

CASTWIN’s High-Definition encoder with the highestvideo quality and low latency. It shows outstandingperformance for inputting signal (Analog & Digital) tooutput as transport stream signal after compressingand encoding for suitable digital transmission withvarious supported formats. Moreover, it supports bothMPEG-2 and H.264 so that it make operator select theformat as they want.Also, it is very easy to control with Hi-class front VFD.

• Component, Composite, HDMI, HD/SD-SDI video inputs.• Low latency as 1,100ms• Digital and Analog audio inputs.• Selectable MPEG-2 or H.264 HD/SD real-time video encoding.

• Selectable outputting of 2xTransport stream (ASI) orUDP/IP transport stream.

• CBR outputs.• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC audio encoding.

• User selectable resolution and bit rate.• Control and monitoring via web browser, front panel or SNMP

• Support Internally generated PSI /PSIP

Feature

• Easily adaptable to a wide range of professional application requiring high level performance functionality.

• Cost effective device with high resolution up to 1080i • Retain your viewers with high performance compression and flawless quality

• Offer user friendly interface with simple set-up and operation

• Compact and light weight design

Competitiveness


DME-9524H

Latency 1100ms

Chroma Format 4:2:0

Resolutions up to 1080i

10



Specification

Video Input


Level 1 Vp-p



Resolutions 480i, 480p, 576i, 576p, 720p, 1080i 25,29.97/30, 50, 59.94/60


Audio Input



Impedance 600 Ω

Connector PS/2

Digital Input Embedded SDI/HDMI

Sampling Rate 48 KHz


Video Encoder

Encoding MPEG-2 MP@HL , MP@ML

H.264 HP@L4, MP@L3

Encoding Rate 3.5~30 Mbps

Chroma Format 4:2:0

PSNR 33dB

Bit Rate Mode CBR

Latency 1100ms~

Audio Encoder

Sampling Rate 48KHz

Dolby Digital® AC-3 128,192,256,384 Kbps

MPEG-1 Layer II 64,96,128,160,192,224,256,320,384 Kbps

MPEG-4 AAC-LC 64,96,128,160,192,224,256,320,384 Kbps

TS Output


Connector BNC(75Ω)

TS Bit Rate 3.5~30 Mbps


IP TS Output

Output 1 Port

Connector RJ-45


Format UDP/IP

IP Address Format Unicast / Multicast

TS Packet Rate 188 Byte

Ethernet

Connector RJ-45


Protocols SNMP

General



Weight 4 kg



Configuration


DME-9524H

11



Introduction

DME-8624S8 is a Multi 8 channel Standard-Definition Encoder, as a newly released product of CASTWIN. It supports MPEG-2 and H.264 encoding and multiplexing with high video quality and low latency. Also, it is cost effective and makes the device widely used in varieties of digital distribution such as CATV/MATV/IPTV digital head-end.

• 8 Channel Encoding• Composite video input• MPEG-2 and H.264 real-time video encoding• Latency as 800 ms• CBR or VBR outputs• Dolby Digital(AC-3), MPEG-1 Layer II audio encoding• User Selectable resolution and bit rate• Control and monitoring via front panel• Excellent IP streaming output

Feature

• Saving your budget opportunities by 8 Channel Encoding

• Ensure critical content quality is preserved by using highest – performance compression and flawless picture quality

• Reduce the installing cost with simple set-up and Compact Size

• Able to Secure space with Compact and light weight design

Competitiveness

Multi 8 channel SD Encoder

DME-8624S8

8 Channel

MPEG-2 & H.264 SD Encoding

Latency 800ms

8 channel Multiplexing

12



Specification

Video Input

Analog Input Composite

Resolutions 480i29.97, 576i25

Aspect Ratio 4:3, 16:9

Audio Input

Analog Input 1 Stereo


Impedance 600 Ω

Video Encoder

Encoding MPEG-2 MP@ML

H.264 MP@L3


H.264 : 0.5~2.5 Mbps

Chroma Format 4:2:0


Latency 800ms~

Audio Encoder

Sampling Rate 48KHz


MPEG-1 Layer II 64, 112~384Kbps

AAC-LC 32 ~ 384Kbps

HE-AAC v1 32 ~ 192Kbps

HE-AAC v2 32 ~ 96Kbps

Multi 8 channel SD Encoder

DME-8624S8

Configuration

TS Output


Connector BNC(75Ω)

TS Bit Rate 1~150 Mbps


IP TS Output

Output 1 Port

Connector RJ-45

Ethernet type 10/100/1000 Base-T

Stream Protocols UDP/IP, RTP/IP


Ethernet

Connector RJ-45


Protocols SNMP

General



Weight 4 kg



13



Introduction

CASTWIN’s the standard definition encoder with thehighest video quality and low latency. It is perfectchoice for customers who are expecting the high-classproducts on video/audio quality. It shows outstandingperformance for inputting signal(Analog & Digital) tooutput as transport stream signal after compressingand encoding for suitable digital transmission withvarious supported formats. Moreover, it supports bothMPEG-2 and H.264 so that it make operator select theformat as they want. Also, it is very easy to control withHi-class front VFD.

• Component, Composite, HDMI, SD-SDI video inputs.• Digital, Analog and SDI embedded audio inputs.• Low latency as 800ms• Additional 1xASI input for supporting of insertion of externally generated PSIP into the transport stream.

• Video input Auto detection function.• Selectable MPEG-2 SD or H.264 SD real-time video encoding.

• Simultaneous outputting of 2xTransport stream (ASI) withUDP/IP or RTP/IP transport stream.

• CBR outputs.• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC, HE-AAC audio encoding.

• Supports internally generated TVCT, CVCT, SDT, NIT• Control and monitoring via web browser, front panel, or SNMP

Feature


• Perfect option for broadcasting of sports, racing with Real time encoding with low latency

• Increase revenue opportunities by enabling additional services

• Reduce the cost of transmission as supporting Wide range of bit-rate control and advanced video coding techniques.

• Additional Cost reduction with Simple set-up and operation

Competitiveness

MPEG-2/4 AVC SD Encoder

DME-8624S

MPEG-2 & H.264 SD Encoding

Latency 800ms

Output ASI / IP Stream

14



Specification

Video Input


Level 1 Vp-p



Resolutions 480i29.97/30, 576i,25


Audio Input

Analog Input 1 Stereo


Impedance 600 Ω

Connector Mini XLR

Digital Input AES-EBU, Embedded SDI/HDMI



Video Encoder

Encoding MPEG-2 MP@ML

H.264 MP@L3


H.264 : 0.5~15 Mbps

Chroma Format 4:2:0


Latency 800ms~

Audio Encoder




MPEC-4 AAC-LC 32~384 Kbps



TS Input


Connector BNC(75Ω)



TS Output


Connector BNC(75Ω)


H.264 : 2.5~19 Mbps


IP TS Output

Output 1 Port

Connector RJ-45





H.264 : 2.5~19 Mbps


Ethernet

Connector RJ-45


Protocols SNMP

General



Weight 4. Kg



Configuration

MPEG-2/4 AVC SD Encoder

DME-8624S

15



Introduction

As a representative decoder, the professional IRD is housed in a space-efficient chassis that receives various signals for decompressing. It is applied in many different kinds of networks, such as broadband fiber, cable, digital terrestrial, satellite and any other distribution network. It is very suitable for broadcast and professional applications requiring 4:2:2/4:2:0 decoding solution.

• MPEG-2/H.264 SD/HD 10bit/8bit 4:2:2/4:2:0 video decoding.• High quality SDI digital video• SD Aspect ratio conversion(4:3, 16:9)• 2 x ASI , RF, IP video inputs• Configured and controlled via front panel LCD.• HD-SDI outputs with embedded audio• HDMI output• Component Video output• Analog 4 stereo outputs. • SNMP control and monitoring • NTSC, PAL video formats• Resolution – up to 1080p 29.97• IP Stream output• Inputs – ATSC, ASI, QAM (Annex B)• 8ch AES/EBU audio input• Video Scaling Option (Up/Down/Cross)

Feature

• Providing your customers with the best performance of decoding and high quality

• Save your cost with various conversion • Able to secure space with Compact and light weight design

• Easy to set-up and control

Competitiveness

DVB-S/S2/S2X Receiving

Latency 100ms


• DVB-CI• Input – DVB-S/S2/T/T2

Options

Integrated Receiver / Decoder

DMD-9724IRD

16



RF Input

Input Channel 1CH

Impedance 75Ω

Module Option DVB-S/S2/T/T2, DVB-C(Annex A, B, C), ATSC

IP Stream Input

No. of Port 1 port

Connector RJ-45

Format 100/1000BaseT

Max Input rate 188Mbps

ASI Input

DVB-ASI2 x BNC

SMPTE310M

Video Decoding

MPEG-2 SD Profile MP@ML(4:2:0) / 422@ML (4:2:2)

Max video rate 80 Mbps

Video format [email protected] fps/576i@25 fps

MPEG-2 HD Profile MP@HL(4:2:0) / 422@HL(4:2:2)


Video format [email protected] fps/25 fps,

[email protected] fps/50 fps

H.264 SD Profile MP@L3(4:2:0) / 422HP@L3 (4:2:2)


Video format [email protected] fps/576i@25 fps

H.264 HD Profile MP@L4 HP@L4 [email protected](4:2:0)

HIGH/HIGH10/[email protected] (4:2:2)


50 Mbps CABAC, 85 Mbps CAVLC

Video format [email protected] fps/25 fps,

[email protected] fps/50 fps

Chroma Format 4:2:0 / 4:2:2 (10bit)


Latency 100ms~

Audio Decoding

Audio Sampling rate 48kHz

MPEG-1 Layer 2 1.0/2.0 decode / pass-through

Dolby® Digital Pro 2.0//5.1 decode / consumer 2.0 decode

Plus 5.1/7.1 decode/5.1 decode &down-min to 2

2.0/5.1 pass-through//plus 5.1/7.1 pass-through

E 2.0/5.1/7.1 pass-through

AAC Audio AAC-LC 2.0/5.1 decode / HE-AAC v1 5.1 decode

HE-AAC v2 2.0 decode

AAC-LC 2.0/5.1 pass-through

Specification

Configuration

ASI Output

DVB-ASI 2 x BNC

Video Output

Analog Output Composite, Component

Digital Output HDMI x 1 , SDI x 2

Resolutions480i29.97, 576i25, 720p50/59.94, 1080p25/29.97


Audio Output

Analog Output 4 balanced stereo pairs


Impedance 600 Ω

Digital Output Embedded SDI/HDMI


IP Stream Output

Interface Type 10/100/1000 Base-T

Stream Protocols UDP/IP, RTP/IP

Broadcasting Multicast, Unicast

General



Weight 4kg




Integrated Receiver / Decoder

DMD-9724IRD

17



Introduction

As a professional MPEG decoder, DMD-9724D is able to receive many different kinds of broadcasting signals and output as various digital interface signals. Moreover; it is able to decode MPEG-2 and H.264 in both 4:2:2 and 4:2:0.

• MPEG-2/H.264 4:2:0(8bit)/4:2:2(10bit) video decoding.• SD Aspect ratio conversion(4:3, 16:9)• Configured and controlled via front panel LCD.• HD-SDI outputs with embedded audio• Composite Video output• Analog stereo outputs.• SNMP control and monitoring• HDMI Output• NTSC, PAL video receiving

Feature

• Providing your customers with the best performance of decoding and high quality

• Able to secure space with Compact and light weight design

• Easy to set-up and control

Competitiveness

Input- DVB-ASI, IP StreamRF(8-VSB, QAM, DVB-T/T2, DVB-S) options

Output – HDMI, HD-SDI, Composite, Component(Option)

Options

MPEG-2 & H.264 Decoding

Latency 100ms


MPEG Decoder

DMD-9724D

18



RF Input

Frequency Range 54~864MHz (8-VSB, QAM, DVB-T,/S)

Input Channel 1CH

Impedance 75Ω

Input Level -25~25dBmV

Return Loss ≥ 17 dB

Noise Figure VHF 7dB, UHF 9dB

TS Input

Transport Stream DVB-ASI 1 port


Connector BNC(75Ω)


H.264 : 2.5~55 Mbps

IP TS Input

IP Stream 1 port

Connector RJ-45

Ethernet type 10/100/1000 Base-T




H.264 : 2.5~55 Mbps

Video Decoder

Decoding MPEG-2 HP@HL, MP@HL , MP@ML

H.264 HP@L4, MP@L3

Bit Rate MPEG-2 : 2~50 Mbps

H.264 : 0.6~50 Mbps

Chroma Format 4:2:0, 4:2:2 (10bit)


Latency 100ms~

Audio Decoder

Sampling Rate 32, 48KHz

Dolby Digital® AC-3(5.1CH) 128,192,256,384,448,512,576,640 Kbps





Specification

Configuration

Video Output

Analog Output Composite, Component(option)

Digital Output HDMI , SDI

Resolutions480i29.97, 576i25, 720p50/59.94, 1080i25/29.97, 1080p25/29.97


Audio Output

Analog Output 1 Stereo


Impedance 600 Ω

Digital Output Embedded SDI/HDMI (4stereo 8ch)

Sampling Rate 32, 48 KHz

Optical Input SPDIF(7.1Channel) Pass Through

Ethernet


Protocols SNMP

General



Weight 4kg




MPEG Decoder

DMD-9724D

19



Introduction

As a representative model of CASTWIN, it is a new released evolutionary product. It is the professional and Hi-class product combining Ultra low delay HD Encoder and ATSC(8-VSB) Modulator. Moreover, it supportsboth MPEG-2 and H.264 so that operator can select and use the format. It is adopting high technology and very effective to make whole Digital Transmission System very compact and easy to controlwith front VFD.

• Advanced modulation integrated• Component, Composite, HDMI, HD/SD-SDI video inputs.• Ultra low latency as 150ms• Digital, Analog and SDI embedded audio(8ch) inputs.• 7.1 channel SPDIF audio optical input(pass through).• Additional 1xASI input for supporting of insertion of externally generated PSIP into the transport stream.

• Provides internally generated PSI and PSIP.• Selectable MPEG-2 or H.264 real-time video encoding.

• Simultaneous outputting of 1xRF and 1xTransport stream (ASI) with UDP/IP or RTP/IP transport stream.

• CBR or VBR outputs.• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC, HE-AAC audio encoding.


• Control and monitoring via web browser, front panel, or SNMP.

• PCR Jitter : ≤ ± 200 ns• Excellent RF Output performance• Scaling function with integrated Advanced Scaler• Phase Noise VHF -105 dB@20KHz, UHF -103 dB@20KHz• Frequency : 54 ~ 1002MHz• MER After Equalizer : 42dB

Feature

• Retain your viewers with high performance compression and flawless quality

• Cost effective solution as a product combined modulator and up-converter


• Best choice for broadcasting of racing, sports via real time encoding with ultra low Latency as 150ms

• Reduce the cost of transmission as supporting wide range of bit-rate control and advanced video coding techniques.

• Able to secure space with compact size for installing

Competitiveness

MPEG HD Mediaplex

DMP-9724M

QAM(Annex A, B and C) ModulationDVB-T Modulation

Options

HD Encoder & Modulator

Latency 150ms

Chroma Format 4:2:0, 4:2:2 (10bit)

Resolutions HD 1080p

20

MPEG HD Mediaplex

DMP-9724M

MPEG HD Mediaplexwww.castwin.com Digital Products MPEG Mediaplexs

Specifications

ITEM CHARACTER

Video Input

Analog Input Component , CompositeDigital Input HDMI , HD-SDI

Level 1000 mVp-p (HDMI) / 800 mVp-p (HD-SDI)

Resolutions 480i29.97, 576i25, 720p50/59.94, 1080i25/29.97


Audio Input

Analog Input StereoFreq. Range 20 Hz ~ 20 KHzImpedance 600 Ω/ 20 KΩ

DigitalInput AES-EBU Embedded SDI/HDMI (4 Stereo 8 Channel)Sampling Rate 32,44.1,48 KHz

Optical Input SPDIF (7.1Channel) Pass Through

TS InputTransport Stream ASI 1 Port Packet Format 188 Byte

Video Encoder


H.264 HP@L4, MP@L3

Encoding Rate MPEG-2 : 0.6~55 Mbps , H.264 : 0.6~50 MbpsChroma Format 4:2:0, 4:2:2 (8 bit/10 bit)PSNR 38 dBBit Rate Mode CBR,VBR

Latency 150 ms~

Audio Encoder


Dolby Digital® AC-3(5.1CH) 128,192,256,384,448,512,576,640 Kbps

MPEG-1 Layer II 64,96,112,128,160,192,224,256,320,384 Kbps




RF Output

Frequency Range 50~1002 MHzImpedance 75 ΩOutput Level 50 ± 5 dBmVLevel Control Range 0 ~ -15 dBMER After Equalizer 42 dBMER Before Equalizer 37 dB

Phase Noise VHF -105 dB@20KHz, UHF -103 dB@20KHz

Adjacent Channel Carrier/Attenuation Characteristic ≤ -45 dB (Out of band)Spurious ≤ -63 dBReturn Loss ≥ 17 dBFrequency Response ± 0.5 dB Frequency Tolerance ± 2 ppmGroup Delay ± 20 ns PCR Jitter ≤ ± 200 ns

TS OutputTransport Stream ASI 1 portTS Bit Rate MPEG-2 : 2.5~55 Mbps , H.264 : 2.5~55 MbpsPacket Format 188 Byte

IP TS Output

(Option)

Output 1 PortConnector RJ-45 Ethernet type 10/100/1000 Base-TStream Protocol UDP/IP, RTP/IPBroadcasting Multicast, Unicast

TS Bit Rate MPEG-2 : 2.5~55 Mbps , H.264 : 2.5~55 Mbps

Ethernet

Connector RJ-45

Interface Type 10/100 Base-T

Protocols SNMP

General

Power Requirements AC 90~230 V, 50/60 HzPower Consumption Max. 100 WWeight 4 KgOperating Temperature -10~50 °CDimensions (W x H x D) 483 x 44 x 383 mm

Configuration

21



Introduction

CASTWIN’s the professional and hi-class product combining low delay HD Encoder and ATSC(8-VSB) Modulator. It is adopting high technology and very effective to make whole Digital TransmissionSystem very compact and easy to control with front VFD. Moreover, it supports both MPEG-2 and H.264 so that operator can select and use the format.

• Component, Composite, HDMI, HD/SD-SDI video inputs.• Digital, Analog and SDI embedded audio inputs.• 5.1 channel SPDIF audio optical input(pass through).• Low latency as 800ms• Additional 1xASI input for supporting of insertion of externally generated PSIP into the transport stream.

• Selectable MPEG-2 HD or H.264 HD real-time video encoding.

• Simultaneous outputting of 1xRF and 1xTransport stream(ASI) with UDP/IP or RTP/IP transport stream

• CBR outputs.• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC, HE-AAC audio encoding.

• Supports internally generated TVCT, CVCT, SDT, NIT• Scaling function with integrated Advanced Scaler• Supports EIA-708 Closed caption insertion via HDSDI(SMPTE 334).

• Control and monitoring via web browser, front panel, or SNMP

• Phase Noise VHF -105 dB@20KHz, UHF -103 dB@20KHz• Frequency : 54 ~ 1002MHz• Excellent RF Output performance

• Cost effective as integrated modulator and up-converter• Excellent option for operators who competitively pursue the best performing encoding device with high resolution

• Best option for Real time encoding with low latency• Able to Secure space with Compact and light weight design

• Make operators pay for less installing fee as offering Quick and easy setup

Competitiveness

MPEG HD Mediaplex

DMP-9624M


Feature

Options


Latency 800ms

Chroma Format 4:2:0

Resolutions 1080p

22



Specification

Video Input



Resolutions480i29.97/30, 576i25, 720p50/59.94/60, 1080i25/29.97/30 1080p25/29.97/30


Audio Input



Impedance 600 Ω

Digital Input AES-EBU Embedded SDI/HDMI

Sampling Rate 32,44.1,48 KHz

Optical Input SPDIF(5.1 Channel) (pass through

TS Input



Video Encoder


H.264 HP@L4 , MP@L3

Encoding Rate MPEG-2 : 2~17.2 Mbps

H.264 : 0.5~17.2 Mbps

Chroma Format 4:2:0


Latency 800ms~

Audio Encoder







RF Output

Frequency Range 54~870 MHz

Impedance 75 Ω

Output Level 50 ± 5 dBmV

Level Control Range 0 ~ -15 dB

MER After Equalizer 42 dB

MER Before Equalizer 37 dB

Phase NoiseVHF -105 dB@20KHz

UHF -103 dB@20KHz

Adjacent Channel Carrier/Attenuation Characteristic

≤ -45 dB (Out of band)

Spurious ≤ -63 dB


Frequency Response ± 0.5 dB

Frequency Tolerance ± 2 ppm

Group Delay ± 20 ns

PCR Jitter ≤ ± 200 ns

TS Output



H.264: 2.5~19 Mbps


Ethernet


Protocols SNMP

IP TS Output

Output 1 Port





H.264: 2.5~19 Mbps


General



Weight 4kg



Configuration

MPEG HD Mediaplex

DMP-9624M

23



Introduction

CASTWIN’s professional and hi-class product combining low delay HD Encoder and ATSC(8-VSB) Modulator.It is adopting high technology and very effective to make whole Digital Transmission System very compact and easy to control with front VFD.

• Component, Composite, HDMI, HD/SD-SDI video inputs• Digital and Analog audio inputs• Low latency as 1,100ms• Selectable MPEG-2 HD or H.264 real-time video encoding.

• CBR outputs.• Dolby Digital (AC-3), MPEG-1 Layer II, AAC-LC audio encoding.

• User selectable resolution and bit-rate, output frequency.• Control and monitoring via web browser, front panel.• PCR Jitter : ≤ ± 200 ns• Group Delay as ± 20 ns• Phase Noise VHF -105 dB@20KHz, UHF -103 dB@20KHz• Frequency : 54~ 1002MHz• Excellent RF Output performance• MER After Equalizer : 42dB• Support Internally generated PSI /PSIP

Feature

• Easily adaptable to a wide range of professional application requiring high level performance functionality.

• Retain your viewers with high performance compression and flawless quality

• Save installing fee with Simple set-up and operation• Retain your viewers with high quality and low attenuation

Competitiveness

MPEG HD Mediaplex

DMP-9524M


Options


Latency 1100ms

Chroma Format 4:2:0

24



Specification

Video Input



Resolutions480i, 480p, 576i, 576p,720p,

1080i 25,29.97/30,50,59.94/60


Audio Input



Impedance 600 Ω/ 20KΩ

Digital Input Embedded SDI/HDMI


Video Encoder


H.264 HP@L4, MP@L3

Encoding Rate 3.5~30 Mbps

Chroma Format 4:2:0

Bit Rate Mode CBR

Latency 1,100ms~

Audio Encoder

Sampling Rate 48KHz


MPEG-1 Layer II 64,96,128,160,192,224,256,320,384 Kbps

AAC-LC (H.264 Only) 64,96,128,160,192,224,256,320,384 Kbps

TS Output


TS Bit Rate 3.5~30 Mbps


RF Output

Frequency Range 54~870 MHz

Impedance 75 Ω


Level Control Range 0 ~ -15 dB

MER After Equalizer ≥ 42 dB

MER Before Equalizer ≥ 37 dB

Phase NoiseVHF -105 dB@20KHz

UHF -103 dB@20KHz

Adjacent Channel Carrier/Attenuation Characteristic

≤ -45 dB (Out of band)

Spurious ≤ -63 dB


Frequency Response ± 0.5 dB

Frequency Tolerance ± 2 ppm

Group Delay ± 20 ns


Ethernet


Protocols SNMP

IP TS Output

Output 1 Port


Format UDP/IP



General



Weight 4kg



Configuration

MPEG HD Mediaplex

DMP-9524M

25



Introduction

CASTWIN’s high-performance ISDB-Tb multiplexer DMX-1908ST is and ideal & cost-effective solution for ISDB-T/Tb transmitter/translator manufacturers, system integrators and broadcaster who want their own ISDB-Tb multiplexer in any region or country where is adopting ISDB-Tb

The DMX-1908ST : ISDB-Tb multiplexer supports SFN with 1PPS & 10MHz input. It provides various re-multiplexing function such as PCR correction, PID re-mapping, and PSI information editing & generating

Transmitter/Translator manufacturers can provide package solution which combines their own ISDB-Tb transmitter/translator and DMX-1908ST : ISDB-Tb together for broadcasters. It will be your strong competitiveness comparing with other competitors who has only exciter or translator. Of course, DMX-1908ST : ISDB-Tb will be a perfect solution for broadcasters who want to find more cost-effective Head-end multiplexer

Additionally, DMX-1908ST supports various global DTV/ mobile TV standards, including ISDB-T, ATSC, ATSC-M/H, CMMB, DVB-T2, and SFCMM on single board.With its FPGA based H/W architecture, user can upgrade new DTV/Mobile TV standards on DMX-1908ST board easily.

• Fully complying with ISDB-T & ISDB-Tb standards• Compact & Cost-effective ISDB-Tb Multiplexer• External 10MHz & 1PP input (SFN supports)• PSI/SI Information editing & generating• PCR Correction and PID re-mapping• IIP Packet editing and inserting• Interoperability proven with major ISDB-Tb Transmitters

Feature

• supports SFN with 1PPS & 10Mhz input• provides various re-multiplexing functions such as

PCR correction, PID re-mapping,, and PSI/SI information editing & generating

• supports various global DTV/Mobile TV Standards,including ISDB-T, ATSC, ATSC-M/H, CMMB, DVB-T2 and SFCMM on single board

Competitiveness

ISDB-T Multiplexer

DMX-1908ST

ISDB-T & ISDB-Tb

Options

Professional ISDB-T / ISDB-Tb

Multiplexer

26



Specification

Input

DVB-ASI input 8EA

GPS 10MHz Reference Clock 1EA

GPS 1PPS Signal 1EA

Multiplexing & Re-multiplexing

TS Multiplexer & Re-multiplexer

PCR Correction

256 PID Mapping for Each Port (TBD)

Automatically Generated PSI/SI Table (TBD)

Modulation Parameter

Mode: Mode1 (2K), Mode2 (4K), Mode3 (8K)

Mode

Guard Interval 1/4 1/8, 1/16, 1/32

Coding Rate 1/4 2/3, ¾, 5/6, 7/8

Constellation DQPSK, QPSK, 16QAM, 64QAM

Layer A, A+B, A+B+C

Bandwidth 6MHz, 7MHz, 8MHz

SFN Parameter

Maximum Time Delay 0ms ~ 1,000ms

Off set -1,000ms ~ +1,000ms

Device ID 0 ~ 30

ISDB-T Multiplexer

DMX-1908ST

Output

DVB-ASI Output 2EA

10MHz Loop Out 1EA

User Control

WEB/Silverlight based Easy GUI via Web

Compatible with Any Web-Browsers

General

Modular Type

Dimension 300 x 180

Weight 0.46Kg

Rack Server Type

Power Requirements AC 85 ~ 286V

Power Consumption 24W

Weight 4.5Kg

Format 1RU rackmount, width 19”

Dimension(W x H x D) 483 x 1RU x 300 mm

27



Introduction

CASTWIN’s High-Performance DVB-T2 Gateway,DMX-1908T2 DVB/T2 Gateway is an ideal & cost-effective solution for DVB-T2 transmitter/translator manufacturers and system integrators who want their own product range in any region or country where is adopting DVB-T2.

The DMX-1908T2 DVB-T2 Gateway encapsulates one or several MPEG-2 TS from DVB-T2 multiplexers into DVB-T2 Base Band frames, and outputs the resulting DVB-T2 multiplex using the DVB-T2 MI (Modular Interface) protocol via ASI and IP. The DVB-T2 MI controls the modular parameters and provides the accurate timing and rate control required in a SFN network. It also supports MISO broadcasting to reinforce SFN performance and management of 8 PLP (Physical Layer Pipes) without any option.

• DVB-T2 MI EncapsulationEncapsulation into Base Band frames Full support of BB frame modes

• DVB-T2 MI interface to the DVB-T2 TransmittersL1 Signaling & SFN time stamp insertion.

• Individual Addressing of DVB-T2 modulatorsMISO (Multi Input Single Output) supportPeak to Average Power Ratio (PAPR) parameters

• Integrated SFN adopterSingle & Multi PLP operationMapping of input TS into individual PLPs

• T2-MI OutputsGeneration of T2-MI packets

Feature

DVB-T2 Gateway

DMX-1908T2

Professional DVB-T2 Gateway

28



Specification

Input

DVB-ASI input 8EA

Ethernet Port (TBD) 2EA

GPS 10MHz Reference Clock 1EA

GPS 1PPS Signal 1EA

Output

DVB-ASI Output 2EA

10MHz Loop Out 1EA

TS Encapsulation in T2-M1 Packets

Single and Multi PLP

NPD (Null Packet Deletion)

ISSY (Input Stream Synchronization) Support

Normal / High Efficiency Mode

Common (L1-Signaling) Parameter

Bandwidth 1.7MHz, 5MHz, 6MHz, 7MHz, 8MHz, 10MHz

FFT 1K, 2K, 4K, 8K, 16K, 32K

Guard Interval 1/4 , 1/8, 1/16, 1/32, 1/128, 19/128, 19/256

Pilot Pattern PP1 ~ PP8

Preamble Format MISO / SISO

Function to Modify DVB-T2 L1 - Signaling

DVB-T2 Gateway

DMX-1908T2

SFN Parameter

Maximum Time delays 0ms ~ 1,000ms

Off Set -1,000 ~ 1,000ms

1PPS Time Reference Input

TS and System Monitoring

Min/Max/Current Bitrate monitoring of Packets for Each Services

Easy-to-use Web based GUI

Monitoring ALL Input / Output and System

Full SNMPv2 support

General

Modular Type

Dimension 300 x 180

Weight 0.46Kg

Rack Server Type

Power Requirements AC 85 ~ 286V


Weight 4.5Kg

Format 1RU rackmount, width 19”

Dimension(W x H x D) 483 x 1RU x 300 mm

29



Introduction

CASTWIN’s NMS offers optimized solution which is very adaptable for various devices. It provides user friendly interface and convenience in order to integrative manage the number of devices easily. Also, it offers Fast-analyzing function to respond for any occurred problem immediately. It uses convenient managing tool set so that it let users manage for CASTWINs. Additionally, it offers warning and notice solution for various cases.

• Realize high advanced network monitoring• Monitoring operation status• Convenient Tab for searching• Sensing for any occurred problem from devices• Management of error, function, solution• Management of data upon occurred error, fluctuation • Monitoring entire network of CASTWIN• Prompt access via Web GUI• Perfect and fast control• Standard up-grade & maintenance

Feature

• CASTWIN’s NMS offers optimized solution to prevent from inconvenience with un-necessary function, inaccurate data, bug etc after set-up.

• CASTWIN’s NMS is much easier to use and install for users compared to other existing NMS.

• Cost effective solution by easy installation and reduction of labor cost

• Enable users to better manage the network and quality of service combined with lower operational costs

Competitiveness

Management System

NMS

30



Introduction

AS a 8-VSB modulator, it is a professional performing product based on the 8-VSB(ATSC) modulation. It shows superior quality to modulate MPEG transport stream as DVB-ASI signal to 8-VSB(ATSC) and output as suitable frequency band for digital broadcasting transmission. Also, it is very easy to control with high class front VFD.

• ASI input transport stream• Excellent RF output• Supports 8-VSB(ATSC) modulation• User adjustable output level and frequency• Front panel control• PCR Jitter: ≤ ± 200 ns• Group Delay as ± 20 ns • Phase Noise VHF -105 dB@20KHz, UHF -103 dB@20KHz• Frequency: 54 ~ 1002MHz • Output Level: 55±5 dBmV• Spurious: ≤ -63dB• MER After Equalizer: 42dB• Highly Advanced fine-tuning

Feature

• Retain your viewer with optimized modulator for ATSC(8-VSB)

• Excellent coding as ITU-T(J.83) Annex D• Cost reduction for installing with simple set-up and operation • Stable output with Hybrid AMP integrated• Secure more space with compact and light weight design

Competitiveness

8-VSB Modulator

DVM-1903ML

Specification

Configuration

Digital Input

Transport Stream DVB-ASIConnector BNC (75Ω)Coding ITU-T (J.83) Annex DBit Rate 19.393 MbpsPacket Format 188ByteSymbol Rate 10.762 Msymbol/sModulation 8-VSB

RF Output

Frequency Range 54~1002MHz

Impedance 75Ω


Level Control Range 0~-15dB

Bandwidth 6MHz

MER After Equalizer ≥ 42 dB

MER Before Equalizer ≥ 37 dB

Phase Noise VHF -105 dB@20KHz

UHF -103 dB@20KHzAdjacent Channel Carrier Attenuation Characteristic ≥ 45 dB (Out-of-band)

Spurious ≤-63 dB


Group Delay ± 20ns

Frequency Response ± 0.5dB

Frequency Tolerance ± 2ppm


General

Power Requirements AC 90~230V, 50/60HzPower Consumption 13WWeight 3KgDimensions 482 x 44 x 383 mm

31



Introduction

AS a QAM modulator, it shows professional performance for received transport stream signal to output as frequency band for suitable CATV band transmission. It is also easy to select frequency band via front control panel.

• ASI input transport stream• Excellent RF output• Supports QAM modulation• Supports PCR re-stamping function• User adjustable output level and frequency• Front panel control• QAM Modulation setting (64, 256QAM)• PCR Jitter: ≤ ± 200 ns• Group Delay as ± 20 ns • MER After Equalizer: 42dB• Phase Noise: VHF -105 dB@20KHz, UHF -103 dB@20KHz• Frequency: 54 ~ 1002MHz• Output Level: 55±5 dBmV• Spurious: ≤ -63dB

Feature

• Hi-dense modulating for QAM(Annex A, B and C) • Advanced coding as ITU-T(J.83) Annex A, B and C • Cost effective with simple set-up and operation • Hybrid AMP integrated

Competitiveness

Specification

Configuration

Digital Input

Transport Stream ASIConnector BNC (75Ω)Coding ITU-T (J.83) Annex A, B and CBit Rate 1~52 MbpsPacket Format 188 ByteSymbol Rate 1~7MbpsModulation 64,256 QAM

RF Output

Frequency Range 54~1002MHzImpedance 75Ω


Level Control Range 0~-15dB

Bandwidth 6MHz : Annex B and C

8MHz : Annex A

MER After Equalizer ≥42 Db

MER Before Equalizer ≥37 dB

Phase Noise VHF -105 dB@20KHz

UHF -103 dB@20KHzAdjacent Channel Carrier Attenuation Characteristic ≥ 45 dB (Out-of-band)

Spurious ≤-63 dB

Return Loss ≥15 dB

Group Delay ±2 0ns

Frequency Response ± 0.5dB

Frequency Tolerance ±2ppm


General

Power Requirements AC 90~230V, 50/60HzPower Consumption 13WWeight 3KgDimensions 482 x 44 x 383 mm

QAM Modulator

DQM-1903ML

32



Introduction

As a NEW released CASTWIN products, It is converts IP to DVB-ASI , or DVB-ASI to IP with GigE Interface. The IP Converter is a cost effective alternative to above both systems, as it connects digital video equipment to easy management. Also it is very easy to control with Hi-class front VFD.

• Received MPEG-2 or H.264 transport streams over Ethernet-based IP networks and converts them to DVB-ASI.

• Received TS as ASI format and output to IP network• SMPTE-2022• Supports IP de-encapsulation and 2D FEC decoding

according to SMPTE 2022-1/2• Interchangeable plugs power adaptor clips US and EU type.

(UK, AUS types are optional)• Inputs : 1 x DVB-ASI and 1 x GigE IP • Outputs: 1 x DVB-ASI and 1 x IP out • Support 7 IP from 1 TS• Support 270Mbpt/s bitrate of DVB-ASI • Support 1ms Latency of ASI to IP • Support IPv4 • Support Unicast and Multicast IP addressing

Feature

Specification

IPASI Converter

DIC-500

Applications• Autonomous IP to ASI gateway• With DIC-500 Tunneling of ASI signals over LAN, WANor the internet

• Remote ASI output adapter for server based datainserters, stream servers, multiplexers and similarsystems

KEY ATTRIBUTES

GigE Port

Physical Layer IEEE 802.3aData rate 10/100/1000Connector RJ-45

ASI Port

Physical Layer DVB-ASI (coax)Connector 75Ω BNC(2x)Ts bitrate < 214 Mbit/s

Transport

TS per IP 1~7Encapsulation UDP or RTPFEC SMPTE 2022

IP to ASI latency 10msJitter tolerance range 1~120ms

CONTROL

IP-address assignment DHCP or static

Multicast support IGMP v2

Front panel control

GENERAL

Power Requirements DC 5V 2A

Weight 0.5kg

Dimensions(W x L x H) 148 x 170 x 35 mm

33



Introduction

As a NEW released CASTWIN products, it is high performance Cross Converter which converts the signal from various inputting formats as HDMI, 3G/HD/SD-SDI, component, composite to various formats. Also, it is integrated with video processor which supports Selectable resolution and improvement for Image enhancing, Phase Noise, control of colors & Gamma.

• Inputs : HDMI, 3G/HD/SD-SDI, Component, Composite. • Outputs : HDMI, 3G/HD/SD-SDI, • Selectable Output Resolution: 480i, 576i, 720p, 1080i, 1080p• HDMI, 3G/HD/SD-SDI supports• 2 Channel Mini XLR audio inputs interface• AES/EBU(BNC), Analog L/R audio input interface• HDMI V1.4 standards support• Upload and configuration via USB2.0• HDMI/SDI Dual Output

Feature

Specification

Multi Digital Scaler

DSR-1000

Competitiveness

• Compact Size and Light Weight• Low Cost & High performance• Simply easy to use • Fully compatible with all your SD and HD device.

Scalar

Max Input Video Resolution 1920x1080@60pMax Output Video Resolution 1920x1080@60p

Frame-rate-conversion

480i(29.9/30), 576i(25), 720p(50/59.94/60)

1080i(25/29.97/30)

1080p(23.98/24/25/29.97/30/50/59.94/60)

Video Input


Digital Input HDMI, 3G/HD/SD-SDI

Resolutions

480i(29.9/30), 576i(25), 720p(50/59.94/60)

1080i(25/29.97/30)

1080p(23.98/24/25/29.97/30/50/59.94/60)

Impedance 75Ω


Analog Composite, Component

Digital HDMI,SD/SDI,3Gb/s SDI

Audio Input

Analog Input Stereo

Frequency Range 20Hz~20KHz

Impedance 600Ω

Connector Mini XLR

Digital Input ASE/EBU, Embedded HDMI/SDI

Sampling Rate 32, 44.1 & 48 KHz

Connector HDMI-19PIN,BNC(75Ω)

SDI

Compliance SMPTE-259/272/274/292/296/299/424/425

Video Rates 4:2:2, 4:4:4

Data Rates SD-SDI : 270Mbps

HD-SDI : 1.5Gb/s & 3Gb/s

Color Space YUV

HDMI

Color Precision 4:2:2, 4:4:4

Version V1.4 Standard

Video Output

Digital Output HDMI, 3G/HD/SD-SDI

Impedance 75 Ω


General



Weight 0.74Kg

Dimensions 270x170x35

34



Introduction

As a NEW released CASTWIN products, it is high performance Cross Converter which converts the signal from various inputting formats as HDMI, 3G/HD/SD-SDI, component, composite to various formats. Also, it is integrated with video processor which supports Selectable resolution and improvement for Image enhancing, Phase Noise, control of colors & Gamma.

• Inputs : HDMI• Outputs : 3G/HD/SD-SDI• Selectable Output Resolution: 480i, 576i, 720p, 1080i, 1080p• HDMI v1.4 standards • Upload and configuration via USB2.0

Feature

Specification

HDMI to SDI Scaler

DSR-500

Competitiveness

• Compact Size and Light Weight• Low Cost & High performance• Simply easy to use • Fully compatible with all your SD and HD device.

Scaler

Max Input Video Resolution 1920x1080@60pMax Output Video Resolution 1920x1080@60p

Frame-rate-conversion480i(29.9/30), 576i(25), 720p(50/59.94/60)

1080i(25/29.97/30)

1080p(23.98/24/25/29.97/30/50/59.94/60)

Video Input

Digital Input HDMI

Resolutions

480i(29.9/30), 576i(25), 720p(50/59.94/60)

1080i(25/29.97/30)

1080p(23.98/24/25/29.97/30/50/59.94/60)



HDMI Version V1.4 Standard

Audio Input

Digital Input Embedded HDMI


Connector HDMI-19PIN

Video Output

Digital Output 3G/HD/SD-SDI

Impedance 75 Ω


ComplianceSMPTE-259/272/274/292/296/299/424/425




Color Space YUV

General



Weight 0.74Kg


DSR-500

HDMI to SDI Scaler

35



Introduction

As a NEW released CASTWIN products, It is the highly advanced multi media converter including SD/HD switching function. It shows best performance to convert from HDMI or SDI or Component or Composite to HDMI and SDI video out simultaneously with embedded HDMI and SDI audio.

• Inputs : HDMI, SDI, Component, Composite• Outputs : HDMI, 3G/HD/SD-SDI, • AES/EBU(BNC) , Analog L/R audio input interface• HDMI, 3G/HD/SD-SDI supports• HDMI v1.4 standards support• HDMI/SDI Dual output• 2Ch Mini XLR Audio inputs interface• Upload and Configuration via USB2.0

Feature

Specification

Multi Media Converter

MMC-1000

MMC-1000

Competitiveness

• Compact size and light weight• Simply easy to use • Fully compatible with all your SD and HD device.

Video Input


Digital Input HDMI, 3G/HD/SD-SDI

Resolutions

480i(29.9/30), 576i(25)720p(50/59.94/60) 1080i(25/29.97/30) 1080p(23.98/24/25/29.97/30/50/59.94/60)

Impedance 75Ω


Audio Input

Analog Input Stereo


Impedance 600Ω

Connector Mini XLR

Digital Input AES/EBU, Embedded HDMI/SDI


Connector HDMI-19PIN,BNC(75Ω)

SDI

Compliance SMPTE-259/272/274/292/296/299/424/425




Color Space YUV

HDMI



Video Output

Digital Output HDMI, 3G/HD/SD-SDI

Impedance 75 Ω


General



Weight 0.74Kg


36



Introduction

It is highly performing Analog to HD/SD-SDI converter for converting from component or composite analog video signal to SDI with stereo audio.

• Input : Component, Composite, Analog L/R• Output : HD/SD-SDI• Upload and configuration via USB2.0

Feature

Specification

Media Converter

ATS-500

Competitiveness

• Compact size and light weight• Simply easy to use• Fully compatible with all your SD and HD devices.

Video Input


Resolutions

480i(29.9/30)

576i(25)

720p(50/59.94/60)

1080i(25/29.97/30)

Impedance 75Ω


Audio Input

Analog Input Stereo


Impedance 600Ω

Connector 6.35mm Phone Jack

Video Output

Digital Output HD/SD-SDI

Impedance 75 Ω


Compliance SMPTE-259/272/274/292/296/299


HD-SDI : 1.5Gb/s


Color Space YUV

General


Weight 0.22Kg

Dimensions 110x90x28 mm

ATS-500

Analog to SDI

37



Introduction

It is superior to convert from SDI to HDMI video out with embedded HDMI audio

• Input : Embedded 3G/HD/SD-SDI• Output : HDMI• HDMI V1.4 standards • SDI loop through output • Upload and configuration via USB2.0

Feature

Specification

Media Converters

STH-500 / HTS-500

Video Input

Digital Input 3G/HD/SD-SDI

Resolutions

480i(29.9/30), 576i(25), 720p(50/59.94/60)

1080i(25/29.97/30)

1080p(23.98/24/25/29.97/30/50/59.94/60)

Impedance 75Ω


Audio Input

Digital Input Embedded SDI

Sampling Rate 48KHz

Connector BNC (75Ω)

SDICompliance SMPTE-259/272/274/292/296/299/424/425




Color Space YUV

HDMIColor Precision 4:2:2, 4:4:4


Video Output

Digital Output HDMI


General


Weight 0.22Kg


STH-500

Introduction

It is superior to convert from HDMI to SDI video out with embedded SDI audio.

• Input : HDMI• Output: 3G/HD/SD-SDI• HDMI V1.4 standards • Upload and configuration via USB2.0

Feature

SpecificationVideo Input

Digital Input HDMI

Resolutions

480i(29.9/30), 576i(25), 720p(50/59.94/60)

1080i(25/29.97/30)

1080p(23.98/24/25/29.97/30/50/59.94/60)


Audio Input

Digital Input Embedded HDMI

Sampling Rate 32,44.1,48KHz

Connector HDMI-19PIN

SDICompliance SMPTE-259/272/274/292/296/299/424/425




Color Space YUV

HDMIColor Precision 4:2:2, 4:4:4


Video Output

Digital Output 3G/HD/SD-SDI

Impedance 75 Ω


General


Weight 0.22Kg


HTS-500

SDI to HDMI HDMI to SDI

38



Documents

No. Products Model No. Pagef02.s.alicdn.com/kf/UT8XJDDXaldXXc_PVbXJ.pdf• 5.1 channel Dolby Digital (AC-3) encoding support • 7.1 channel SPDIF audio optical input (pass through)