NMS300 - Quick Start Guide - - Quick Start Guide RGB... · NMS300 Quick Start Guide ... BS EN 55022:1998 page 1
NMS300 - Quick Start Guide - - Quick Start Guide RGB... · NMS300 Quick Start Guide ... BS EN 55022:1998 page 2

NMS300 - Quick Start Guide - - Quick Start Guide RGB... · NMS300 Quick Start Guide ... BS EN 55022:1998

  • View
    222

  • Download
    0

Embed Size (px)

Text of NMS300 - Quick Start Guide - - Quick Start Guide RGB... · NMS300 Quick Start Guide ... BS EN...

  • NMS300 Quick Start Guide For the complete manual please download from:http://newall.com/nms300 Warnings The mains supply is connected into a switch mode power supply (separate from your NMS300) via a detach-able supply cord (supplied). If another supply cord is used, it must have fitted a C5, 10A, EARTHED mains connector with a cord rated for at least 10A.

    If a mains plug is not already fitted to the supply cord or is of the wrong type, then a suitable EARTHED plug should be used which complies with the relevant specifications for plugs and socket-outlets.

    You can only use the NMS300 with Newall Spherosyn300 and Microsyn300 encoders.

    Unit only to be serviced by Newall qualified personnel or authorised alternatives.

    If a Spherosyn300 encoder travels over 3.2m an error message will be displayed, see full manual for details.

    Turn off the power by disconnecting the power supply connector before you connect the encoder(s)

    Technical SpecificationEnvironmentalOperating Temperature Storage Temperature 0 to 50C -20 to 70C

    Environmental Conditions - IP40 (Stand Alone)

    Relative Humidity - maximum 95% for temperature up to 31C

    DisposalAt the end of its life, you should dispose of the NMS300 in asafe manner applicable to electronic goods.The case work is suitable for recycling. Please consult local regulations on disposal.

    ElectricalEU Directive 73/23/EEC (Low Voltage-Direc-tive)BS EN 55022:1998 Class BBS EN 55024:1998

    Input to power supply unit (supplied)100-240V (47-63Hz)

    External switch-modeoutput voltage 15VDC

    Conforms to low voltage directive

    Note: Newall Measurement Systems reserve the right to change specification without notice

    Connections

    SIZEA2

    DRAWING NUMBER 316-87851

    REV.ISS. 0 DO NOT SCALE THIRD ANGLE PROJECTION IF IN DOUBT ASK

    UNLESS OTHERWISE TOLERANCES: - 0 DECIMAL PLACES 0.5 STATED: - 1 DECIMAL PLACES 0.2 2 DECIMAL PLACES 0.1DIMENSIONS ARE IN M.M ANGULAR 1

    DRAWING NUMBER

    REV.ISS.316-87851 0

    SCALE

    SHEET1 OF 1

    MATERIAL/FINISH

    THIS DRAWING IS THE PROPERTY OFNEWALL MEASUREMENT SYSTEMS LTD.

    THE INFORMATION THERON MAY NOT BE COPIED OR USEDWITHOUT WRITTEN PERMISSIONLeicester England

    TITLEOEM DRO MOUNTING DETIALS

    DRAWNDATE

    chris.wh29/09/2016REV.ISS. DATE C.N.No ALTERATION

    75.0097.50

    38.0

    035

    .00

    STANDARD MOUNTING OPTION A

    4 OFF M4 x 0.7mm 7.0 DEEP

    -STANDARD FDMI 'TYPE C' CENTRE MOUNTING FOR DISPLAYS - SHOULD FIT STANDARD MONITOR WALL MOUNTS AND CAN BE USED TO CONVERT TO OTHER MOUNTING ARMS e.g. COMPETITORS MOUNTS.

    42.7

    3

    55.7

    3

    NEWALL MOUNTING OPTION B

    M10x1.5 - 6H

    -M10 THREAD- DIE CAST ADAPTOR FITS INTO THE STANDARD HOLE PITCH OF OPTION A WILL BE FACTORY FITTED IF ORDERED. OR COULD BE USED BY OEM TO CONVERT PANEL MOUNT TO STAND ALONE. - FITS ALL EXISITNG NEWALL MOUNTING ARMS. - THIS WILL BE MOST COMMON OPTION.

    120.

    00

    2.50

    210.002.50

    PANEL CUTOUT DIMS

    76.0

    035

    .00

    75.007.50

    90.00

    7.00

    10.00

    BRACKET - OUTLINE DIMS

    4.50

    3.00

    30.2014.50

    PANEL MOUNTING OPTION C

    -MOUNTED ON SQUARE BOSS ON BACK PANEL. -BRACKET FITS STANDARD HOLES ON BACK PANEL.ALLOWING EASY CONVERSION BETWEEN PANEL MOUNT AND STAND ALONE. -OEM COULD KEEP STOCK OF BOTH BRACKETS THEN FIT AS REQUIRED

    N/A 2:1

    EUROPENewall Measurement Systems Ltd.

    Technology Gateway, Cornwall Road SouthWigston, Leicester LE18 4XH

    United KingdomTel: +44 (0) 116 264 2730

    sales@newall.co.ukwww.newall.co.uk

    AMERICASNewall Electronics Inc.

    USATel: +1 614 771 0213

    CHINA & TAIWANSensata Technologies China Co., Ltd

    Peoples Republic of ChinaTel: +86 212 2306 1500

    SINGAPORE & KOREASensata Technologies Co., Ltd

    SingaporeTel: +65 647 86 867

    JAPANSensata Technologies Japan Ltd.

    JapanTel: +81 45 277 7120

    More information at sales@newall.com www.newall.com

    Part No: 023-?????-UK

    Encoder input connection 2 or 3

    according to model

    External PSU input Cabinet equipotential terminal for grounding to machine

  • Understanding the keypad

    SIZEA3

    DRAWING NUMBER

    REV.ISS.

    DO NOT SCALE THIRD ANGLE PROJECTION IF IN DOUBT ASK

    UNLESS OTHERWISE TOLERANCES: - 0 DECIMAL PLACES 0.5 STATED: - 1 DECIMAL PLACES 0.2 2 DECIMAL PLACES 0.1DIMENSIONS ARE IN M.M ANGULAR 1

    DRAWING NUMBER

    REV.ISS.

    SCALE

    SHEET1 OF 1

    MATERIAL/FINISH

    THIS DRAWING IS THE PROPERTY OFNEWALL MEASUREMENT SYSTEMS LTD.

    THE INFORMATION THERON MAY NOT BE COPIED OR USEDWITHOUT WRITTEN PERMISSIONLeicester England

    TITLE

    DRAWNDATE

    chris.wh25/11/2016REV.ISS. DATE C.N.No ALTERATION

    Zero an axis in zero mode

    Zero an axis in set mode

    Pre-set an axis

    Entering setup

    SIZEA3

    DRAWING NUMBER

    REV.ISS.

    DO NOT SCALE THIRD ANGLE PROJECTION IF IN DOUBT ASK

    UNLESS OTHERWISE TOLERANCES: - 0 DECIMAL PLACES 0.5 STATED: - 1 DECIMAL PLACES 0.2 2 DECIMAL PLACES 0.1DIMENSIONS ARE IN M.M ANGULAR 1

    DRAWING NUMBER

    REV.ISS.

    SCALE

    SHEET1 OF 1

    MATERIAL/FINISH

    THIS DRAWING IS THE PROPERTY OFNEWALL MEASUREMENT SYSTEMS LTD.

    THE INFORMATION THERON MAY NOT BE COPIED OR USEDWITHOUT WRITTEN PERMISSIONLeicester England

    TITLE

    DRAWNDATE

    chris.wh25/11/2016REV.ISS. DATE C.N.No ALTERATION

    SIZEA3

    DRAWING NUMBER

    REV.ISS.

    DO NOT SCALE THIRD ANGLE PROJECTION IF IN DOUBT ASK

    UNLESS OTHERWISE TOLERANCES: - 0 DECIMAL PLACES 0.5 STATED: - 1 DECIMAL PLACES 0.2 2 DECIMAL PLACES 0.1DIMENSIONS ARE IN M.M ANGULAR 1

    DRAWING NUMBER

    REV.ISS.

    SCALE

    SHEET1 OF 1

    MATERIAL/FINISH

    THIS DRAWING IS THE PROPERTY OFNEWALL MEASUREMENT SYSTEMS LTD.

    THE INFORMATION THERON MAY NOT BE COPIED OR USEDWITHOUT WRITTEN PERMISSIONLeicester England

    TITLE

    DRAWNDATE

    chris.wh25/11/2016REV.ISS. DATE C.N.No ALTERATION

    SIZEA3

    DRAWING NUMBER

    REV.ISS.

    DO NOT SCALE THIRD ANGLE PROJECTION IF IN DOUBT ASK

    UNLESS OTHERWISE TOLERANCES: - 0 DECIMAL PLACES 0.5 STATED: - 1 DECIMAL PLACES 0.2 2 DECIMAL PLACES 0.1DIMENSIONS ARE IN M.M ANGULAR 1

    DRAWING NUMBER

    REV.ISS.

    SCALE

    SHEET1 OF 1

    MATERIAL/FINISH

    THIS DRAWING IS THE PROPERTY OFNEWALL MEASUREMENT SYSTEMS LTD.

    THE INFORMATION THERON MAY NOT BE COPIED OR USEDWITHOUT WRITTEN PERMISSIONLeicester England

    TITLE

    DRAWNDATE

    chris.wh25/11/2016REV.ISS. DATE C.N.No ALTERATION

    SIZEA3

    DRAWING NUMBER

    REV.ISS.

    DO NOT SCALE THIRD ANGLE PROJECTION IF IN DOUBT ASK

    UNLESS OTHERWISE TOLERANCES: - 0 DECIMAL PLACES 0.5 STATED: - 1 DECIMAL PLACES 0.2 2 DECIMAL PLACES 0.1DIMENSIONS ARE IN M.M ANGULAR 1

    DRAWING NUMBER

    REV.ISS.

    SCALE

    SHEET1 OF 1

    MATERIAL/FINISH

    THIS DRAWING IS THE PROPERTY OFNEWALL MEASUREMENT SYSTEMS LTD.

    THE INFORMATION THERON MAY NOT BE COPIED OR USEDWITHOUT WRITTEN PERMISSIONLeicester England

    TITLE

    DRAWNDATE

    chris.wh25/11/2016REV.ISS. DATE C.N.No ALTERATION

    950.355

    100.250

    -156.755

    mm Abs Zero

    SIZEA3

    DRAWING NUMBER

    REV.ISS.

    DO NOT SCALE THIRD ANGLE PROJECTION IF IN DOUBT ASK

    UNLESS OTHERWISE TOLERANCES: - 0 DECIMAL PLACES 0.5 STATED: - 1 DECIMAL PLACES 0.2 2 DECIMAL PLACES 0.1DIMENSIONS ARE IN M.M ANGULAR 1

    DRAWING NUMBER

    REV.ISS.

    SCALE

    SHEET1 OF 1

    MATERIAL/FINISH

    THIS DRAWING IS THE PROPERTY OFNEWALL MEASUREMENT SYSTEMS LTD.

    THE INFORMATION THERON MAY NOT BE COPIED OR USEDWITHOUT WRITTEN PERMISSIONLeicester England

    TITLE

    DRAWNDATE

    chris.wh25/11/2016REV.ISS. DATE C.N.No ALTERATION

    SIZEA3

    DRAWING NUMBER

    REV.ISS.

    DO NOT SCALE THIRD ANGLE PROJECTION IF IN DOUBT ASK

    UNLESS OTHERWISE TOLERANCES: - 0 DECIMAL PLACES 0.5 STATED: - 1 DECIMAL PLACES 0.2 2 DECIM