Nikon - prior.com · 1 Nikon Automation Guide Introduction This brochure is designed to provide an overview of the equipment we produce for a range of Nikon microscopes

Nikon Automation Guide

Nikon Automation Guide

www.prior.com

More to Prior than meets the eye

1 Nikon Automation Guide

Introduction

This brochure is designed to provide an overview of the equipment we produce for a range of Nikon microscopes.

Please note that the equipment in this guide is not an exhaustive list and instead shows the more common products that can be mounted on these microscopes. Additionally, other Nikon microscopes can have Prior equipment added to them.

More information about our products can be found by contacting a Prior representative, emailing [email protected] or by visiting www.prior.com.

We also have an extensive collection of datasheets which are freely available on our website (www.prior.com), or via contacting Prior Scientific.

The parts to be selected will depend both upon the microscope make and the end-user’s application.

We highly recommend contacting a Prior Sales Manager before ordering.

At the end of this guide you will find a short explanation of our stage codes.

2 www.prior.com

Contents

Nikon FN1 3

Nikon Ti/Ti2 7

Nikon Ni (Focussing Stage) 11

Nikon NI (Focussing Nosepiece) 15

Nikon AZ100 19

Nikon SMZ 18/25 23

Nikon LV100 and LV150 27

Nikon L200 and L300 31

Nikon TS2R 35

Nikon Ci 39

Nikon MA100 43

Nikon MA200 45

Nikon ProZ Stand 49

Stage Guide 53

Please note that the parts may vary in availability and part numbers and specifications may change without warning. Whilst we have attempted to verify that the information here is accurate, we cannot guarantee that it is completely up to date and error free; thus we suggest contacting Prior before ordering in order to ensure that all equipment will be compatible with your microscope and suitable for your application. The microscopes featured here are for illustrative purposes only. All intellectual property relating to these microscopes, including patents and trademarks, remain the property of their respective owners. Nikon is a registered trademark of Nikon Corporation. ProScan®, OptiScan® and ZDeck® and the Prior Scientific logo are registered trademarks of Prior Scientific Ltd. The 5 year warranty applies to stages used only with a Prior controller, for full details, terms and conditions of the warranty please visit www.prior.com. This document is © Prior Scientific 2017. Nikon Sales Brochure July 2017 V.1.6.

Products listed in green on the systems charts require the ProScan ® III Control System to be

operated


Z-Deck- ZDN12MP- ZDN12ME- ZDN12MK- ZDN12MF

Z-Deck Sample Holders- HZ202- HZ203

Sample holders- H224LP- H224PLP- H234LP

Slide Loader- PL2001

- PL2382 OR PL2282

- PL304- PL310

NanoScanZ3

- NZ200F

Motorised stages - H101NFN- HIP4NFN- HEP4NFN- PL101NFN† - PLE01NFN†‡

HZP Post Mounts- HZP150- HZP200- HZP250- HZP300

Post Sample Holder- HZP1000- HZP1010- HZP1020

Translation Stage- ZDP50T- ZDP50K

(HZ201 adapter

Nikon FNI

4 www.prior.com

Lumen 100- L100###NI(Replace ### with wavelength)

Brightfield- LDB103NI- LDB10FNI

Controllers- ES10ZE - V31XYZE- V31F- V31XYZEF

Lumen 200 - L220SNI- L200SNI

Joystick Control Unit- PS3J100

Focus Motor- NIKRFK + NIKFN1MA- NIKRFK + NIKFN1EK -PS3H122R + H3940

Filter wheels- HF108A/HF220 (Excitation)- HF110A/HF220 (Excitation)

Shutters- HF200HT (Excitation)- HF201HT (Excitation)

Lumen 200 - L220NI- L200NI

Nikon FNI


Product Details

ES10ZE Focus only controllerH101NFN H101A stage with 2mm screw pitch and 200 step motorH1P4NFN H101A stage with 1 mm screw pitch and 400 step motorH224LP Low profile slide holder H224PLP Low profile slide holder (71 x 51 mm slide holder)H234LP Low profile slide holder for 4 71 x 21 mm slidesHEP4NFN H101A stage with 1mm screw pitch, 400 step motor and encodersHF108A/HF220 8 position 32 mm filter wheel with adapterHF110A/HF220 10 position 25 mm filter wheel with adapterHF200HT High speed shutter with 25 mm apertureHF201HT High speed shutter with 32 mm apertureHZ201 Adapter allowing upright sample holders to be inserted into Z-DeckHZ202 Solid Insert Plate for Z-DeckHZ203 108 mm ring insert plate for Z-DeckH3940 Adapter to connect PS3H122R focus motor to FN1 microscope HZP150 Rigid post mount 150 mm tall HZP200 Rigid post mount 200 mm tallHZP250 Rigid post mount 250 mm tallHZP300 Rigid post mount 300 mm tallHZP1000 Manipulator holder for HZP150/200/250/300 HZP1010 Standard sample holder for HZP150/200/250/300HZP1020 Circular holder for HZP150/200/250/300 L100###NI Single LED illumination system. Replace ### with wavelength required.L200NI Metal Halide Illumination Source L200SNI Metal Halide Illumination Source with integral shutter.L220NI Metal Halide Illumination Source with extended UV/IR wavelengthsL220SNI Metal Halide Illumination Source with integral shutter with extended UV/IR wavelengths

Nikon FNI

6 www.prior.com

Notes

1) The slide loader can only be used with the PL101FN or PLE01FN stages

2) The PLE01FN is only for use with the PL228

3) The NZ200F can only be used with the Z-Deck

Product Details

LDB102NI Brightfield Illumination LED for Nikon (standalone)LDB103NI Brightfield Illumination LED for Nikon (ProScan control)NIKFN1EK Adapter for Nikon FN1 for NIKRFK (encoded)NIKFN1MA Adapter for Nikon FN1 for NIKRFKNIKRFK Nikon remote focussing kit - includes controller, cables and focus motorNZ200F NanoScanZ (adapted for flat top stages)PL200 Slide LoaderPL228 Bevel edged sample holder for “1 x 3” slides. Includes 4 slide racks for for “1 x 3” slidesPL238 Bevel edged sample holder for “2 x3” slides. Includes 2 slide racks for “2 x 3” slidesPL310 Elevated baseplate to improve clearance PL304 Barcode reader for PL200PL101NFN H101A stage for use with slide loaderPLE01NFN Encoded H101A stage for use with Slide Loader (use with PL228 only)PS3J100 Multifunctional manual joystick for ProScanPS3H122R Generic focus motor; requires H3940 focus adapter.V31F ProScan® controller with three stepper drives for focus and two filter wheels or 3 shuttersV31XYZE ProScan® controller with XYZ drives and encoder inputV31XYZEF ProScan® controller with XYZ drives, three filter wheel drives, shutter drives and encoder inputZDN12MP Motorised Z-Deck quick adjust platform system ZDN12ME Motorised Z-Deck quick adjust platform system (Encoded)ZDN12MK Manual Z-Deck quick adjust platform systemZDN12MF Fixed plate Z-Deck quick adjust platform systemZDP50K Translation stage for microscope (manual)ZDP50T Translation stage for microscope (motorised). Includes OptiScan controller

Nikon FNI


NanoScan Z stages- NZ400

NanoScanZ Sample holders- NZ303 (NZ400)- NZ302 (NZ400)- NZ301 (NZ400)

NanoScanZ Incubation Chambers- W3719 (NZ400)

Sample holders- H473XR- H223XRNC- H229XR-H224XRLP

Incubationchambers - W4184

Motorised stages - H117P1N4- H117E1N4Option to add H117ACCM

Linear stages - HLD117NN(HLD324 adapter required for use of Prior Sample Holders) Well Plate Loader

- PLW20N- PLW106

Two wellplate stages - H139P1NN- H139E1N5

H139 Sample holders- H171XR- H223XR2- H473R3

Nikon TiNikon Ti/Ti2

8 www.prior.com

Lumen 100- L100###NI

(Replace ### with wavelength)

Focus Motor- PS3H122R + H2975 / H122KON

Controllers- ES10ZE - V31XYZE- V31F- V31XYZEF- VLD31XYZ- VLD31XYZEF

Lumen 200

- L220SNI- L200SNI


Shutters- HF200HT (Excitation)- HF201HT (Excitation)- HF202HT + HF220 (Excitation)- HF204HT + HF220 (Excitation)


Nikon Ti Hub Integration kit - LDBNHUB

Filter wheels- HF110A + HF220 (Excitation)- HF110A + HF255 (Emission)- HF108A + HF248 (Emission)- HF108A + HF220 (Excitation)- HF6NTK (Motorised turret)- HF110/32A + HF220 (Excitation)- HF110/32A + HF255 (emission)

Nikon Ti/Ti2

Brightfield- LDB103NI- LDB102NI


Product Details

ES10ZE Focus only system controllerACCM Extension plates for H117 stages H117E1N4 H117 motorised stage with 1mm screw pitch and encodersH117P1N4 H117 motorised stage with 1mm screw pitch H139P1NN H139 motorised stage with 1 mm ballscrew, 400 stepper motorH139E1N5 H139 motorised stage with 1 mm ballscrew, 400 stepper motor and 50 nm encoderH171XR 9 Slide holder for H139H122KON Direct fine focussing kit for Nikon and Olympus MicroscopesH223XRNC Extra recessed low profile microtitre plate for H117 stagesH223XR2 2 micro titre plate holder from H139H224XRLP Extra recessed low profile slide holder for H117 stages H229XR Extra recessed petri dish holder for H117 stagesH473XR Extra recessed low profile universal holder for H117 stagesH473XR3 Double Universal Sample Holder for H139HF108A/HF220 Filter wheel holding 8 32 mm filters with adapter (Excitation)HF110A/HF220 Filter wheel holding 10 25mm filters with adapter (Excitation)HF110A/HF255 Filter wheel holding 10 25mm filters with adapter (Emission)HF108A/HF248 Filter wheel mounted underneath nosepiece (Emission)HF11032A/HF220 Filter wheel holding 10 32 mm filters with adapter (Excitation)HF11032A/HF255 Filter wheel holding 10 32 mm filters with adapter (Emission)HF200HT High speed shutter with 25mm aperture for use with filter wheelHF201HT High speed shutter with 32mm aperture for use with filter wheelHF202HT/HF220 High speed shutter with 25mm aperture for stand alone use, with adapterHF204HT/HF220 High speed shutter with 32mm aperture for stand alone use, with adapterHF6NTK Upgrade to motorised turret allowing control via ProScan HLD117NN Linear motor stage with travel range of 81 x 121 mm and 50 nm encodersHLD324 Required to adapt linear stages for Prior insertHLW223XR Required to adapt linear stages for the PLW20. Check with Nikon for condenser and objective compatibilityL100###NI Single LED illumination system. Replace ### with wavelength requiredL200NI Metal Halide Illumination Source L200SNI Metal Halide Illumination Source with integral shutterL220NI Metal Halide Illumination Source with extended UV/IR wavelengthsL220SNI Metal Halide Illumination Source with integral shutter and with extended UV/IR wavelengths

Nikon Ti/Ti2

10 www.prior.com

Notes Depending on the exact variant of Ti/Ti2, some Prior parts may not be compatible. Please contact Prior before ordering with the exact variant of microscope.

Product Details

LDB102NI Brightfield Illumination LED for Nikon (standalone)LDB103NI Brightfield Illumination LED for Nikon (ProScan control)LDBNHUB Integrates the Brightfield into the Nikon Ti HubNZ301 Extra recessed well plate holder for NZ400NZ302 Extra recessed slide/petri dish holder for NZ400NZ303 Extra recessed slide holder for NZ400NZ400 Nanopositioning piezo Z stage with 400 um of travel and controllerPS3H122R/H2975 Focus drive and adapterPS3J100 Multifunctional manual joystick for ProScanPLW106 Barcode reader for Well Plate LoaderPLW107 Kit to raise Nikon Ti E to correct level when using PLW20PLW20 Well Plate LoaderV31F ProScan® Controller with three stepper drives for filters, shutters or a focus driveV31XYZE ProScan® Controller with X Y Z drives and encoder capabilityV31XYZEF ProScan® controller with XYZ drives, three filter wheel drives, three shutter drives and encoder capabilityVLD31XYZ ProScan® controller with XYZ drives for linear stage controlVLD31XYZF ProScan® controller with XYZ drives, three filter wheel drives, and three shutter drives for linear stage control W3569 Incubation chamber for NZ100/200W3719 Incubation chamber for NZ400W4184 Incubation chamber for H117 stages

Nikon Ti/Ti2


Flat top Motorised stages3 - H101E1CI/NI (dependent on substage)- H101P1CI/NI (dependent on substage)- H101P2CI/NI (dependent on substage)-H101E2CI/NI (dependent on substage)

Sample holders- H224LP- H234LP


- PL2382 OR PL2282

- PL304- PL310

Sample holders (Flat top)- H224F- H234F

Sample holder adapterH3848

NanoScanZ4

- NZ200F

Motorised stages3

- H101E50/E80 (dependent on substage)- HIP4E50/E80 (dependent on substage)- HEP4E50/E80 (dependent on substage)- PL101E50/E80 (dependent on substage)- PLE01E50/E80 (dependent on substage)

8 Slide Stage3

- H138E50/E80 (dependent on substage) - HE38E50/E80 (dependent on substage)

Sample holders (H138A)- H238LP- H238PLP- H239

Nikon NiFocussing Stage

12 www.prior.com








Focus Motor- PS3H122R + H122KON + H3940- NIKRFK + NIKNIMA




Product Details

ES10ZE Focus only controllerH101E50/E80 H101A stage with 2mm screw pitch and 200 step motorH101E1CI/NI H101F flat top stage with 1 mm screw pitch, 200 step motors and encodersH101P1CI/NI H101F flat top stage with 1mm screw pitch and 200 step motors.H101P2CI/NI H101F flat top stage with 2mm screw pitch and 200 step motors.H101E2CI/NI H101F flat top stage with 2 mm screw pitch, 200 step motors and encodersH1P4E50/E80 H101A stage with 1 mm screw pitch and 400 step motorH138E50/E80 H138A Eight slide holding stage with 200 step motor and 2mm ball screw HE38E50/E80 H138A Eight slide holding stage with 200 step motor and 2mm ball screw and encodersH224F Low profile slide holder for flat top stagesH224LP Low profile slide holder H234F Low profile slide holder for flat top stages for four 76 x 26 mm slides H234LP Low profile slide holder, for four 76 x 26 mm slides H122KON Direct fine focus coupling kit for Nikon and OlympusH234F Low profile slide holder (4 slides) for flat top stagesH238LP Low profile slide holder for eight 76 x 26 mm slides H238PLP Semi recessed low profile slide holder for eight 76 x 26 mm slides H239 Aluminium plate for H138A and HE38 H3848 Adapter allowing conventional sample holders to be fitted to flat top stagesH3940 Adapter for PS3H122R (Nikon Ni-U and Ni-C only)HEP4E50/E80 H101A stage with 1mm screw pitch, 400 step motor and encodersHF108A/HF220 8 position 32 mm filter wheel with adapterHF110A/HF220 10 position 25 mm filter wheel with adapterL100###NI Single LED illumination system. Replace ### with wavelength required.L200NI Metal Halide Illumination Source L200SNI Metal Halide Illumination Source with integral shutter.L220NI Metal Halide Illumination Source with extended UV/IR wavelengthsL220SNI Metal Halide Illumination Source with integral shutter with extended UV/IR wavelengths


14 www.prior.com

Notes 1The slide loader can only be used with the PL101E50/E80 or PLE01E50/80 stages

2 The PLE01E50/80 is only for use with the PL228

3 The suffix E50 OR CI is applicable for Ni microscopes with a SS Sub-stage. For SSR sub-stages add E80 or NI instead

4 NZ200F can only be used with flat top stages

Product Details

LDB102NI Brightfield Illumination LED for Nikon (standalone)LDB103NI Brightfield Illumination LED for Nikon (ProScan control)PS3H122R Generic Focus Drive with rotating cable system to prevent twistingNIKNIMA Adapter for Nikon Ni for NIKRFKNIKRFK Nikon remote focussing kit - includes controller, cables and focus motorNZ200F NanoScanZ (adapted for flat top stages)PL200 Slide LoaderPL228 Bevel edged sample holder for “1 x 3” slides. Includes 4 slide racks for for “1 x 3” slidesPL238 Bevel edged sample holder for “2 x3” slides. Includes 2 slide racks for “2 x 3” slides.PL304 Barcode reader for PL200PL310 Elevated baseplate to improve clearance PLE01E50/E80 Encoded H101A stage for use with Slide Loader (use with PL228 only)PL101E50/E80 H101A stage for use with slide loaderPS3H122R Generic focus drive with rotating cable system to prevent twistingPS3J100 Multifunctional manual joystick for ProScanV31F ProScan® controller with three stepper drives for focus and two filter wheels or 3 shuttersV31XYZE ProScan® controller with XYZ drives and encoder inputV31XYZEF ProScan® controller with XYZ drives, three filter wheel drives, shutter drives and encoder input



Z-Deck Sample Holders- HZ202- HZ203

Sample holders- H224LP- H224PLP- H234LP

Slide Loader- PL200†- PL238‡ OR PL228‡- PL304- PL310

NanoScanZ*- NZ200F

Motorised stages - H101NFN- HIP4NFN- HEP4NFN- PL101NFN† - PLE01NFN†‡

HZP Post Mounts- HZP150- HZP200- HZP250- HZP300

Post Sample Holder- HZP1000- HZP1010- HZP1020

(HZ201 adapter

Z-Deck- ZDN 12MP- ZDN12ME- ZDN12MK- ZDN12MF

Nikon NiFocussing Nosepiece

16 www.prior.com








Translation Stage- ZDP50T- ZDP50K




Product Details

ES10ZE Focus only controllerH101NFN H101A stage with 2mm screw pitch and 200 step motorH1P4NFN H101A stage with 1 mm screw pitch and 400 step motorH224F Low profile slide holder for flat top stagesH234F Low profile slide holder for flat top stages for four 76 x 26 mm slides H224LP Low profile slide holder H224PLP Low profile slide holder (71 x 51 mm slide holder)H234LP Low profile slide holder for 4 71 x 21 mm slidesHEP4NFN H101A stage with 1mm screw pitch, 400 step motor and encodersHF108A/HF220 8 position 32 mm filter wheel with adapterHF110A/HF220 10 position 25 mm filter wheel with adapterHF200HT High speed shutter with 25 mm apertureHF201HT High speed shutter with 32 mm apertureHZ201 Adapter allowing upright sample holders to be inserted into Z-DeckHZ202 Solid Insert Plate for Z-DeckHZ203 108 mm ring insert plate for Z-DeckHZP150 Rigid post mount 150 mm tall HZP200 Rigid post mount 200 mm tallHZP250 Rigid post mount 250 mm tallHZP300 Rigid post mount 300 mm tallHZP1000 Manipulator holder for HZP150/200/250/300 HZP1010 Standard sample holder for HZP150/200/250/300HZP1020 Circular holder for HZP150/200/250/300 L100###NI Single LED illumination system. Replace ### with wavelength requiredL200NI Metal Halide Illumination Source L200SNI Metal Halide Illumination Source with integral shutterL220NI Metal Halide Illumination Source with extended UV/IR wavelengthsL220SNI Metal Halide Illumination Source with integral shutter with extended UV/IR wavelengthsLDB102NI Brightfield Illumination LED for Nikon (standalone)LDB103NI Brightfield Illumination LED for Nikon (ProScan control)NZ200F NanoScanZ (adapted for flat top stages)


18 www.prior.com

Product Details

NZ200F NanoScanZ (adapted for flat top stages)PL200 Slide LoaderPL228 Bevel edged sample holder for “1 x 3” slides. Includes 4 slide racks for for “1 x 3” slidesPL238 Bevel edged sample holder for “2 x3” slides. Includes 2 slide racks for “2 x 3” slidesPL310 Elevated baseplate to improve clearance PL304 Barcode reader for PL200PL101NFN H101A stage for use with slide loaderPLE01NFN Encoded H101A stage for use with Slide Loader (use with PL228 only)PS3J100 Multifunctional manual joystick for ProScanV31F ProScan® controller with three stepper drives for focus and two filter wheels or 3 shuttersV31XYZE ProScan® controller with XYZ drives and encoder inputV31XYZEF ProScan® controller with XYZ drives, three filter wheel drives, shutter drives and encoder inputZDN12MP Motorised Z-Deck quick adjust platform system ZDN12ME Motorised Z-Deck quick adjust platform system (Encoded)ZDN12MK Manual Z-Deck quick adjust platform systemZDN12MF Fixed plate Z-Deck quick adjust platform systemZDP50K Translation stage for microscope (manual)ZDP50T Translation stage for microscope (motorised)

Notes 1) The slide loader can only be used with the PL101FN or PLE01FN stages

2) The PLE01FN is only for use with the PL228

3) The NZ200F can only be used with the Z-Deck



Flat top Motorised stages3

- H101E1AZEP- H101P1AZEP- H101P2AZEP

Sample holders- H224LP- H473UP


Sample holder adapter

NanoScanZ4

- NZ200F

Motorised stages3

- H101AZEP/E50- HIP4AZEP/E50- HEP4AZEP/E50- PL101AZEP/E50- PLE01AZEP/E50

8 Slide Stage3

- H138AZEP/E50- HE38AZEP/E50


Nikon AZ100

20 www.prior.com


Lumen 200 - L220S- L200S- L220- L200


Focus Motor- PS3H122S15


- PL2382 OR PL2282

- PL304

Focus Motor- PS3H122R + H2531


Product Details

ES10ZE Focus only controllerH101ZEP/E50 H101A stage with 2mm screw pitch and 200 step motorH101E1AZEP H101F flat top stage with 1 mm screw pitch, 200 step motors and encodersH101P1AZEP H101F flat top stage with 1mm screw pitch and 400 step motorsH101P2AZEP H101F flat top stage with 2mm screw pitch and 200 step motorsH101E2AZEP H101F flat top stage with 2 mm screw pitch and 200 step motors and encodersH1P4ZEP/E50 H101A stage with 1 mm screw pitch and 400 step motorH138ZEP/E50 H138A Eight slide holding stage with 200 step motor and 2mm ball screw HE38ZEP/E50 H138A Eight slide holding stage with 200 step motor and 2mm ball screw and encodersHEP4ZEP/E50 H101A stage with 1mm screw pitch, 400 step motor and encodersH224F Low profile slide holder for flat top stagesH224LP Low profile slide holder H234F Low profile slide holder (4 slides) for flat top stagesH238LP Low profile slide holder for eight 76 x 26 mm slides H238PLP Semi recessed low profile slide holder for eight 76 x 26 mm slides H239 Aluminium plate for H138A and HE38 H2531 Adapter for PS3H122R to fit to AZ100H3848 Adapter allowing conventional sample holders to be fitted to flat top stagesH473UP Universal sample holderL200 Metal Halide Illumination Source L200S Metal Halide Illumination Source with integral shutterL220 Metal Halide Illumination Source with extended UV/IR wavelengthsL220S Metal Halide Illumination Source with integral shutter with extended UV/IR wavelengthsNZ200F NanoScanZ (adapted for flat top stage)

Nikon AZ100

22 www.prior.com

Notes 1 The slide loader can only be used with the PL101ZEP/E50 or PLE01ZEP/E50 stages

2 The PLE01ZEP/E50 is only for use with the PL228

3 AZEP is for Episcopic AZ100s, E50 for diascopic

4 NZ200F can only be used with flat top stages

Note that the AZ100 only accepts liquid light guides so remove adaptors and collimators from illumination devices

Product Details

PL200 Slide LoaderPL228 Bevel edged sample holder for “1 x 3” slides. Includes 4 slide racks for for “1 x 3” slidesPL238 Bevel edged sample holder for “2 x3” slides. Includes 2 slide racks for “2 x 3” slidesPL304 Barcode reader for PL200PL101ZEP/E50 H101A stage for use with slide loaderPLE01ZEP/E50 Encoded H101A stage for use with Slide Loader (use with PL228 only)PS3H122R Generic focus drive with rotating cable system to prevent twistingPS3H122RS15 Focus motor adapted for AZ100 PS3J100 Multifunctional manual joystick for ProScanV31F ProScan® controller with three stepper drives for focus and two filter wheels or 3 shuttersV31XYZE ProScan® controller with XYZ drives and encoder inputV31XYZEF ProScan® controller with XYZ drives, three filter wheel drives, shutter drives and encoder input


Flat top Motorised stages - H101P2F- H101E2F

Sample holders- H224LP- H473UP


Sample holder adapter-H3848

NanoScanZ- NZ200F

Adapter-HSMZ1825

Laser Autofocus- LF210- LF100K- LF320

OptiScan Stage1

- ES111

Nikon SMZ18/25

24 www.prior.com

Controllers*- ES10ZE - ES111

- V31XYZE- V31F- V31XYZEF *Compatible with mostimaging software

Lumen 200 - L220S- L200S- L220- L200

Joystick Control Unit- PS3J100- CS1525DP

Focus Motor- PS3H122S15


Product Details

CS152DP OptiScan III JoystickES10ZE Focus only controllerES11 OptiScan III Controller ES111 ES11 stage with 125 x 75 mm travelH101P2F H101F flat top stage with 2mm screw pitch and 200 step motors H101E2F H101F flat top stage with 2mm screw pitch and 200 step motors with encodersH224F Low profile slide holder for flat top stagesH224LP Low profile slide holder H234F Low profile slide holder (4 slides) for flat top stagesH3848 Adapter allowing conventional sample holders to be fitted to flat top stagesH473UP Universal sample holderHSMZ1825 Adapter for mounting stages on the SMZ1825L200 Metal Halide Illumination Source L200S Metal Halide Illumination Source with integral shutterL220 Metal Halide Illumination Source with extended UV/IR wavelengthsL220S Metal Halide Illumination Source with integral shutter with extended UV/IR wavelengthsLF100K LF210 Digipot and KeypadLF210 Laser AutoFocus (requires flange and keypad)LF320 LF210 Mounting flange for Nikon MicroscopesNZ200F NanoScanZ (adapted for flat top stage)PS3H122S15 Focus motor adapted for SMZ 18 (not suitable for SMZ 25)PS3J100 Multifunctional manual joystick for ProScanV31F ProScan® controller with three stepper drives for focus and two filter wheels or 3 shuttersV31XYZE ProScan® controller with XYZ drives and encoder inputV31XYZEF ProScan® controller with XYZ drives, three filter wheel drives, shutter drives and encoder input

Notes

1 The ES111 stage can ONLY be controlled by the ES11 controller. Consult Prior Scientific for the difference between OptiScan and ProScan control systems and stages

Nikon SMZ18/25

26 www.prior.com

SMZ 800/1000/1270/1500 Stage Addition

Older SMZ Microscopes can be enhanced with Prior equipment, mostly in a similar way to the SMZ18/25. The optimal stage configuration will depend on the illumination base on the stereo microscope.

This guide only applies for the SMZ 800, SMZ 1000, SMZ1270 and SMZ 1500 stereo microscopes from Nikon. For the grey cells, the correct configuration is the addition of ‘E600’ to the stage.

Stage Stage description Adapter to be used Light Base Light Base Description

P2-PB Plain base

P2-DBL LED Diascopic illumination

base H101P2F Flat top, 200 step, 2 mm

ballscrew HSMZ1825 P2-DBF Fiber Diascopic illumination

base HE01E2F Encoded flat top, 200 step,

2 mm ballscrew P-PS32 Plain stand

P-DSL32 LED Diascopic illumination

stand

P-DSF32 Fiber Diascopic illumination

stand C-DS Diascopic stand S

H101P2FE600 Flat top, 200 step, 2 mm ballscrew C-PS160 Plain stand

H101E2FE600 Encoded flat top, 200 step, 2 mm ballscrew C-DSD115 DIA stand

H101E600 200 step, 2 mm ballscrew H448 C-DSD230 DIA stand H1P4E600 400 step, 1 mm ballscrew C-DSDF DIA stand F

HEP4E600 Encoded 400 step, 1 mm ballscrew C-DSS115 DIA stand

C-DSS230 DIA stand

Nikon SM800/1000/1270/1500


Flat top Motorised stages- H101P2NLV- H101E1NLV- H101P1NLV

Sample holders- H220- H234LP- H224LP- HWC15SNL (H105)- HWC15VNL (H105)- H231 (H105)- H227 (H105)

Sample holders (Flat top)- H220F- H230F- H224F- H234F

Sample holder

adapterH3848

NanoScanZ1

- NZ200F

Motorised stages- H101NLV- HIP4NLV- HEP4NLV- H105N2F

8 Slide Stage- H138NLV- HE38NLV


Nikon LV100/150

28 www.prior.com

Controllers- ES10ZE - V31XYZE- V31F- V31XYZEF Compatible with mostimaging software

Joystick Control Unit- PS3J100Focus Motor

- PS3H122R/H3909




Product Details

ES10ZE Focus only controllerH101E1NLV H101F flat top stage with 1 mm screw pitch, 200 step motors and encodersH101NLV H101A stage with 2mm screw pitch and 200 step motorH101P2NLV H101F flat top stage with 2mm screw pitch and 200 step motorsH105N2F Large format stage with 154 x 154 mm travel range, 200 step motors and 2 mm screw pitchH101P1NLV H101F flat top stage with 1mm screw pitch and 400 step motors.H1P4NLV H101A stage with 1 mm screw pitch and 400 step motorH138NLV H138A Eight slide holding stage with 200 step motor and 2mm ball screw HE38NLV H138A Eight slide holding stage with 200 step motor and 2mm ball screw and encodersH220 Glass insert plateH220F H101F glass insert plateH224F Low profile slide holder for flat top stagesH224LP Low profile slide holder (76 x 26 mm slide)H227 Glass plate (H105 stages) - not suitable for transmitted microscopyH230 Aluminium insert plateH230F H101F aluminium insert plateH231 Aluminium plate (H105 stages)H234F Low profile slide holder (4 slides) for flat top stagesH224LP Low profile slide holder (4 x 26 x 76 mm slides)H238LP Low profile slide holder for eight 76 x 26 mm slides H238PLP Semi recessed low profile slide holder for eight 76 x 26 mm slides H239 Aluminium plate for H138A and HE38 H3848 Adapter allowing conventional sample holders to be fitted to flat top stagesH3909 Focus Motor Adapter for Nikon LV series and L200 HE05NL/2 Encoded variant of H105/2HEP4NLV H101A stage with 1mm screw pitch, 400 step motor and encodersHWC15SNL Wafer chuck for 100 and 150 mm wafers (H105 stages)HWC15VNL Wafer chuck, rotatable with vacuum for 150 mm (H105 stages)LDB102NI Brightfield Illumination LED for Nikon (standalone)LDB103NI Brightfield Illumination LED for Nikon (ProScan control)LF100K LF210 Digipot and KeypadLF210 Laser AutoFocus (requires flange and keypad)LF320 LF210 Mounting flange for Nikon MicroscopesNZ200F NanoScanZ (adapted for flat top stages)

Nikon LV100/150

30 www.prior.com

Notes 1 NZ200F can only be used with flat top stages

Product Details

PS3H122R Generic Focus Drive with rotating cable system to prevent twistingPS3J100 Multifunctional manual joystick for ProScanV31F ProScan® controller with three stepper drives for focus and two filter wheels or 3 shuttersV31XYZE ProScan® controller with XYZ drives and encoder inputV31XYZEF ProScan® controller with XYZ drives, three filter wheel drives, shutter drives and encoder input


Large format motorised stages1 - H116/2-8- HE16/2-8- H105N2F

Sample holders for large format stages - H225 (H116)- H232 (H116)- HWC20S (H116)- HWC20V (H116)- HWC15SNL (H105)- HWC15VNL (H105)- H231 (H105)- H227 (H105)

Sample holders for large format stages - H223 (H112)- H223 (H112)- H223B (H112)- HWC30V (H112)

Large format motorised stages1 - H112/2ST- HE12/2ST

L300 ONLY

Nikon L200/300

32 www.prior.com

Controllers- ES10ZE - V31XYZE- V31F- V31XYZEF Compatible with mostimaging software


Focus Motor- PS3H122R/H3909




Product Details

ES10ZE Focus only controllerH112/2ST Stage with 300 x 300 mm travel range and 2 mm ball screwHE12/2ST As above with encodersH116/2-8 Large format stage with 255 x 215 mm travel range, 200 stepper motor and 2 mm screw pitchHE16/2-8 As above with encodersH105N2F Large format stage with 154 x 154 mm travel range, 200 step motors and 2 mm screw pitchH221 Glass Plate (H112 stages) - not suitable for transmitted microscopy H225 Glass plate (H116 stages) - not suitable for transmitted microscopyH227 Glass plate (H105 stages) - not suitable for transmitted microscopyH231 Aluminium plate (H105 stages)H233 Aluminium plate (H112 stages)H233B Aluminium plate with M4 and M6 tapped holes (H112 stages)H232 Aluminium plate (H116 stages)H3909 Focus Motor Adapter for Nikon LV series and L200 HWC15SNL Wafer chuck for 100 and 150 mm wafers (H105 stages)HWC15VNL Wafer chuck, rotatable with vacuum for 150 mm (H105 stages)HWC20S Wafer chuck for for 150 mm and 200 mm wafers (H116 stages)HWC20V Wafer chuck, rotatable with vacuum for 200 mm wafers (H116 stages) HWC30S Wafer chuck, rotatable, for 300 mm wafers (H112 stages)LDB102NI Brightfield Illumination LED for Nikon (standalone)LDB103NI Brightfield Illumination LED for Nikon (ProScan control)LF100K LF210 Digipot and KeypadLF210 Laser AutoFocus (requires flange and keypad)LF320 LF210 Mounting flange for Nikon MicroscopesPS3H122R Generic Focus Drive with rotating cable system to prevent twistingPS3J100 Multifunctional manual joystick for ProScanV31F ProScan® controller with three stepper drives for focus and two filter wheels or 3 shuttersV31XYZE ProScan® controller with XYZ drives and encoder inputV31XYZEF ProScan® controller with XYZ drives, three filter wheel drives, shutter drives and encoder input

Notes

1 Only the L300 can accommodate H112 stages

Nikon L200/300

34 www.prior.com

NOTES


NanoScanZ Sample holders- H499XR (NZ100/200)- H472XR (NZ100/200)- H471XR (NZ100/200)- NZ303 (NZ400)- NZ302 (NZ400)- NZ301 (NZ400)

NanoScanZ Incubation Chambers- W3569 (NZ10/2000)- W3719 (NZ400)

Sample holders- H473XR- H223XRNC- H229XR-H224XRLP

Motorised stages - H117P1N4- H117E1N4Option to add H117ACCM

Linear stages - HLD117NN(HLD324 adapter required for use of Prior Sample Holders)

H139 Stages- H139P1N4- H139E1N4

H139 Sample holders- H171XR- H223XR2- H473R3

Nikon TS2R

36 www.prior.com

Focus Motor- PS3H122R + H2975 / H122KON

Controllers- ES10ZE - V31XYZE- V31F- V31XYZEF- VLD31XYZ- VLD31XYZEF

Lumen 200* - L220S- L200S- L220- L200



Nikon TS2R


Product Details ES10ZE Focus only system controllerH117ACCM Extension plates for H117 stages H117E1N4 H117 motorised stage with 1mm screw pitch and encodersH117P1N4 H117 motorised stage with 1mm screw pitch H122KON Direct fine focussing kit for Nikon and Olympus MicroscopesH139P1N4 H139 motorised stage with 1 mm ballscrew, 400 stepper motorH139E1N4 H139 motorised stage with 1 mm ballscrew, 400 stepper motor and 100 nm encoderH171XR 9 slide holder for H139H223XRNC Extra recessed low profile microtitre plate for H117 stagesH223XR2 2 micro titre plate holder for H139H224XRLP Extra recessed low profile slide holder for H117 stages H229XR Extra recessed petri dish holder for H117 stagesH473XR Extra recessed universal holder for H117 stagesH473XR3 Double Universal sample holder for H139HLD117NN Linear motor stage with travel range of 81 x 121 mm and 50 nm encodersHLD324 Required to adapt linear stages for Prior insertL200 Metal Halide Illumination Source L200S Metal Halide Illumination Source with integral shutterL220 Metal Halide Illumination Source with extended UV/IR wavelengthsL220S Metal Halide Illumination Source with integral shutter and with extended UV/IR wavelengths NZ301 Extra recessed well plate holder for NZ400NZ302 Extra recessed slide/petri dish holder for NZ400NZ303 Extra recessed slide holder for NZ400NZ400 Nanopositioning piezo Z stage with 400 um of travel and controllerPS3H122R/H2975 Focus drive and adapterPS3J100 Multifunctional interactive control centre for ProScanV31F ProScan® Controller with three stepper drives for filters, shutters or a focus driveV31XYZE ProScan® Controller with X Y Z drives and encoder capabilityV31XYZEF ProScan® controller with XYZ drives, three filter wheel drives, three shutter drives and encoder capabilityVLD31XYZ ProScan® controller with XYZ drives for linear stage controlVLD31XYZF ProScan® controller with XYZ drives, three filter wheel drives, and three shutter drives for linear stage controlW3569 Incubation chamber for NZ100/200W3719 Incubation chamber for NZ400

Nikon TS2R

38 www.prior.com

NOTES


Flat top Motorised stages - H101E1CI - H101P1CI- H101P2CI- H101E2CI

Sample holders- H224LP- H234LP


Sample holder adapterH3848

Motorised stages- H101E50- HIP4E50- HEP4E50

8 Slide Stage - H138E50 - HE38E50

Ci

40 www.prior.com






Shutters- HF200HT/HF220 (Excitation)- HF201HT/HF220 (Excitation)


Focus Motor- PS3H122R + H122KON + H3940

Sample holders (H138A)

- H238LP- H238PLP- H239

Ci




Product Details

ES10ZE Focus only controllerH101E50 H101A stage with 2mm screw pitch and 200 step motorH101E1CI H101F flat top stage with 1 mm screw pitch, 200 step motors and encodersH101P1CI H101F flat top stage with 1mm screw pitch and 400 step motorsH101P2CI H101F flat top stage with 2mm screw pitch and 200 step motorsH101E2CL H101F flat top stage with 2 mm screw pitch and 200 step motorsH1P4E50 H101A stage with 1 mm screw pitch and 400 step motorH138E50 H138A Eight slide holding stage with 200 step motor and 2mm ball screw HE38E50 H138A Eight slide holding stage with 200 step motor and 2mm ball screw and encodersH224F Low profile slide holder for flat top stagesH224LP Low profile slide holder H234F Low profile slide holder for flat top stages extra recessed, for four 76 x 26 mm slides H234LP Low profile slide holder, extra recessed, for four 76 x 26 mm slides H122KON Direct fine focus coupling kit for Nikon and OlympusH234F Low profile slide holder (4 slides) for flat top stagesH238LP Low profile slide holder for eight 76 x 26 mm slides H238PLP Semi recessed low profile slide holder for eight 76 x 26 mm slides H239 Aluminium plate for H138A and HE38 H3848 Adapter allowing conventional sample holders to be fitted to flat top stagesH3940 Adapter for PS3H122R HEP4E50 H101A stage with 1mm screw pitch, 400 step motor and encodersHF108A/HF220 8 position 32 mm filter wheel with adapterHF110A/HF220 10 position 25 mm filter wheel with adapterHF200HT/HF220 High Speed Shutter 25 mm aperture for use with filter wheel with adapterHF201HT/HF220 High Speed Shutter 32 mm aperture for use with filter wheel with adapterL100###NI Single LED illumination system. Replace ### with wavelength required.L200NI Metal Halide Illumination Source L200SNI Metal Halide Illumination Source with integral shutterL220NI Metal Halide Illumination Source with extended UV/IR wavelengthsL220SNI Metal Halide Illumination Source with integral shutter with extended UV/IR wavelengthsLDB102NI Brightfield Illumination LED for Nikon (standalone)LDB103NI Brightfield Illumination LED for Nikon (ProScan control)PS3H122R Generic Focus Drive with rotating cable system to prevent twistingNZ200F NanoScanZ (adapted for flat top stages)PS3H122R Generic focus drive with rotating cable system to prevent twisting

Ci

42 www.prior.com

Product Details

PS3J100 Multifunctional manual joystick for ProScanV31F ProScan® controller with three stepper drives for focus and two filter wheels or 3 shuttersV31XYZE ProScan® controller with XYZ drives and encoder inputV31XYZEF ProScan® controller with XYZ drives, three filter wheel drives, shutter drives and encoder input

Ci


Focus Motor- PS3H122R/H3550

Brightfield- LDB102NI

Controllers- ES10ZE - ES11- CS515DP

OptiScan stage- ES107NTS

Sample Holders- H224ROTS- H473- H649- H656- H659

Nikon MA100

44 www.prior.com

Product Details

CS52DP OptiScan III JoystickES10ZE Focus only controllerES107NTS OptiScan motorised stage 125 x 75 mmES11 OptiScan III ControllerH224ROTS Recessed rotating holder for one 26 x 76 mm slideH473 Universal Specimen Holder for slides and petri dishesH649 Holder for a single 1”, 1.25” and 1” metallurgical slide specimenH656 Holder for a single metallurgical specimen, 1.25” diameterH659 Holder for one mounted metallurgical specimen, 15” diameter with 1,2,4 or 8 chambers.LDB102NI BrightfieldIlluminationLEDforNikon(standalone)PS3H122R/H3550 Focus motor and adapter


Focus Motor- PS3H122R + H3273


Lumen 200 - L200S- L220S- L200- L220

Note that the collimator must be removed

C-HGFI/C-HGFIE required

MA200

46 www.prior.com



NanoScanZ Sample holders- NZ303 (NZ400)- NZ302 (NZ400)- NZ301 (NZ400)

Sample holders- H473XR- H234XR- H224XRLP- H649- H656- H657- H658- H659

Motorised stages - H117N2M4- H117N1M4



Product Details

ES10ZE Focus only system controllerH117P1M4 H117 motorised stage with 1mm screw pitch H234XRLP Low profile slide holder, extra recessed, for one 76 x 51 mm slideH234 Low profiles slide holder, extra recessed, for four 76 x 26 mm slidesH649 Holder for 1”, 1.25” and 1.5” mounted metallurgical specimensH656 Holder for 1.25” mounted metallurgical specimens H657 Holder for 1 2” mounted metallurgical specimenH658 Holder for 6 mounted metallurgical specimens 1.25” diameterH659 Holder for one mounted metallurgical specimen, 1.5” in diameter with 1 2 4 or 8 chambersL200 Metal Halide Illumination Source L200S Metal Halide Illumination Source with integral shutterL220 Metal Halide Illumination Source with extended UV/IR wavelengthsL220S Metal Halide Illumination Source with integral shutter and with extended UV/IR wavelengths L300DLG 3 LED illumination system for with single band filter set with UV/Violet peak at 365 nm and light guideLDB102NI Brightfield Illumination LED for Nikon (standalone)LDB103NI Brightfield Illumination LED for Nikon (ProScan control)NZ301 Extra recessed well plate holder for NZ400NZ302 Extra recessed slide/petri dish holder for NZ400NZ303 Extra recessed slide holder for NZ400NZ400 Nanopositioning piezo Z stage with 400 um of travel and controllerPS3H122R/H3273 Focus drive and adapterPS3J100 Multifunctional manual joystick for ProScanV31F ProScan® Controller with three stepper drives for filters, shutters or a focus driveV31XYZE ProScan® Controller with X Y Z drives and encoder capabilityV31XYZEF ProScan® controller with XYZ drives, three filter wheel drives, three shutter drives and encoder capability

Nikon MA200

48 www.prior.com

NOTES


Sample holders- H224LP (H101 stages ) - H473UP (H101 stages )- H230 (H101 stages) - H220 (H101 stages)- H227 (H105 stages) - H231 (H105 stages)- H225 (H116 stages) - H232 (H116 stages)- H233 (H112 stages) - H221 (H112 stages)

Adapter for LV series- ZCALV

Lumen 200 - L220NI- L200NI- L220SNI- L200SNI

ProZ Stand- ZC12- ZC12EL - ZC12FL

Controllers- ES10ZE - V31XYZE- V31F- V31XYZEF Compatible with most imaging software

Joystick Control Units - PS3J100

Pillar Mounting AdapterZC12FLNG

ProZ stand for Nikon

Brightfield- LDB103NI- LDB10FNI

50 www.prior.com

Motorised stages- H101- HIP4- HEP4- H105N2F

Large Format Motorised stages- H116/2- HE16/2- H112/2ST- HE12/2ST

Mounting stand- H414 (for usewith ZC12EL)-H413

Stage mount ZCBRLZCBTL

Focus Blocks- FB201- FB203- FB204/4- FB205/E- FB206/E

Clamping ArmsZCBCK

Adapter for AZ100- ZCAAZ- ZCAAZS (ZC12EL only)

Adapter for SMZ18/25- ZCASMZ25- ZZCASMZ25S (ZC12EL only)



Product Details

ES10ZE Focus only controllerFB201 Manual focussing blockFB203 Motorised Linear AxisFB204 Motorised focus holding an incident light Prior stage; with flanges for fitting to optical tableFB204E As above with EncodersFB205 Motorised focus with offset base holding an incident light Prior stage with flanges for fitting to optical tableFB205E As above with encodersFB206 Motorised focus holding a transmitted light Prior stage with flanges for fitting to optical tableFB206E As above with encodersH101 H101A stage with 2mm screw pitch and 200 step motorH105N2F Large format stage with 154 x 154 mm travel range, 200 step motors and 2 mm screw pitchH112/2ST Large format stage with 302 x 302 mm travel range, 200 stepper motor and 2 mm screw pitchH116/2 Large format stage with 255 x 215 mm travel range, 200 stepper motor and 2 mm screw pitchH1P4 H101A stage with 1 mm screw pitch and 400 step motorH220 Glass plate (H101 stages) - not suitable for transmitted microscopyH221 Glass plate (H112 stages) - not suitable for transmitted microscopyH224LP Low profile slide holder (H101 stages)H225 Glass plate (H116 stages) - not suitable for transmitted microscopyH227 Glass plate (H105 stages) - not suitable for transmitted microscopyH230 Aluminium plate (H101 stages)H231 Aluminium plate (H105 stages)H232 Aluminium plate (H116 stages)H233 Aluminium plate (H112 stages)H413 Mounting stand for H101 or H105 stagesH414 Mounting stand for H112 or H116 stagesH473UP Universal sample holder (H101 stages)HE12/2ST Encoded variant of H112/2STHE16/2 Encoded variant of H116/2HEP4 H101A stage with 1mm screw pitch, 400 step motor and encoders


52 www.prior.com

Product Details

L200NI Metal Halide Illumination Source L200SNI Metal Halide Illumination Source with integral shutter.L220NI Metal Halide Illumination Source with extended UV/IR wavelengthsL220SNI Metal Halide Illumination Source with integral shutter with extended UV/IR wavelengthsLDB102NI Brightfield Illumination LED for Nikon (standalone)LDB103NI Brightfield Illumination LED for Nikon (ProScan control)PS3J100 Multifunctional manual joystick for ProScanV31F ProScan® controller with three stepper drives for focus and two filter wheels or 3 shuttersV31XYZE ProScan® controller with XYZ drives and encoder inputV31XYZEF ProScan® controller with XYZ drives, three filter wheel drives, shutter drives and encoder inputZC12 Motorised Z column with 500 mm2 base and 250 mm of travelZC12EL Motorised Z column with approx 600 x 750 mm base and 250 mm of travel ZC12FL Motorised Z column with no base and 250 mm of travel ZC12FLNG Adapter for mounting ZC12FL to optical mounting table ZCAAZ Nikon AZ100 Optical Mounting ArmZCAAZS Extended AZ100 Optical Mounting Arm (ZC12EL only)ZCALV Nikon LV Optical Mounting ArmZCASMZ25 Nikon SMZ18/25 Optical Mounting ArmZCASNZ25S Extended SMZ1/25 Optical Mounting Arm (ZC12EL only)ZCBCK Universal clamping kit for illumination basesZCBRL H101, H105 stage mount reflected light only. Add HP1770 for manual stage dovetail option.ZCBTL Prior H101, H105 stage mount transmitted light. Accepts 50mm diffuser/filter. Includes Prior LDB101 LED light source

Notes Note that H116 and H112 stages require ZC12EL and H414



This indicates the microscope type the stage fits to and stepper motor the stage has:

NN: Nikon, 200 stepper motorN4: Nikon, 400 stepper motorMA: Nikon, 200 stepper motor (MA200 only)M4: Nikon, 400 stepper motor (MA200 only)

This indicates the ballscrew of the stage:

1: 1 mm ballscrew2: 2 mm ballscrew

This indicates whether the stage is encoded or not:

P: Not currently encoded (upgrade available)E: Encoded

H101F FLAT TOP STAGE FOR UPRIGHT MICROSCOPES

H101P2FThis indicates the microscope type the stage is

suitable for:

F: SMZ18/25 (requires HSMZ1825 adaptor) NI: Nikon (SSR substage)CI: Nikon (SS substage)ZEP: Nikon (AZ100)

This indicates the ballscrew of the stage:

1: 1 mm ballscrew2: 2 mm ballscrew This indicates whether the stage is encoded or not:

P: Not currently encoded (upgrade available)E: Encoded

H117 STAGE FOR INVERTED MICROSCOPES

H117E1#4

This indicates the ballscrew of the stage;

0: 2 mm ballscrewP: 1 mm ballscrew


1: Not currently encoded (upgrade available)E: Encoded

H101A STAGE FOR UPRIGHT MICROSCOPES

H101A This indicates the microscope type the stage fits to;

E50: Nikon (SS substage)E80: Nikon (SSR substage) AZEP: Nikon (AZ100)LV: Nikon LV100/LV150A: Nikon SMZ18/25 (requires HSMZ1825 adaptor)

This indicates the stepper motor of the stage:

1: 200 stepper motor4: 400 stepper motor



H138A STAGE FOR UPRIGHT MICROSCOPES

H138A This indicates the microscope type the stage fits to:

E50: Nikon (SS substage)E80: Nikon (SSR substage) AZEP: Nikon (AZ100)NLV: Nikon LV100/LV150

Stage Codes for Nikon

54 www.prior.com



H112 STAGE FOR UPRIGHT MICROSCOPES

H112/2STThis indicates the pitch ball screw:

2: 2 mm ballscrew pitch5: 5 mm ballscrew pitch




H116/2STThis indicates the pitch ball screw:

2: 2 mm ballscrew pitch5: 5 mm ballscrew pitch


H105/N2F

This indicates which microscope the stage fits to:

-8: Nikon (LV200 requires H2100 spacer plate and range must be limited to 200mm)

This indicates what drives the Z deck:P: Stepper Motor (Unencoded)E: Stepper Motor (Encoded)K: Manual controlF: Fixed (no movement possible)

ZDN12MP

This indicates whether the stage is encoded:

1: Not currently encoded (upgrade available)E: 50 nm encoders

H139 MULTI-WELL PLATE STAGE

H139#1## This indicates the microscope type the stage fits to:

NN: Nikon Ti N5: Nikon TiNote that the suffix alters depending on the presence or absence of encoders.

Z-DECK

Stage Codes for Nikon

There are currently no encoded variants for the H105/N2F.


Since 1919 Prior Scientific has been producing precision equipment for microscopy. With decades of experience, expert staff, a vast range of products and extensive design, manufacture and assembly facilities, Prior Scientific can supply equipment for all manner of microscopy applications.


More to Prior than meets the eye

WORLDWIDE DISTRIBUTION

Prior Scientific LtdCambridge • UK

t: +44 (0)1223 881711e: [email protected]

Prior Scientific IncRockland • MA. • USA

t: +1 781-878-8442 e: [email protected]

Prior Scientific GmbH Jena • Germany

t: +49 (0) 3641 675 650e: [email protected]

Prior Scientific KK Tokyo • Japan

t: +81-3-5652-8831e: [email protected]

Documents

Nikon - prior.com · 1 Nikon Automation Guide Introduction This brochure is designed to provide an overview of the equipment we produce for a range of Nikon microscopes