News 2017 - Camozzi Pneumatics – USA – Fittings, … · news 2017 93-1500-0gb027 11/2016. ... > high flow performances > very low internal volume ... body peek seals fkm - epdm

Series K8DV directly operated solenoid valves with separating diaphragm

Series K directly operated solenoid valves

Series 8 pneumaticallyand electropneumatically operated valves

Series VNR unidirectional cartridge valve

Series TC1-V 2/2-way shut-off micro-valve

Series AP directly operated proportional valves

Series CP directly operated proportional valves

Series TC-1R cartridge pressure regulator

News 2017

93-1

500-

0GB

027

11/

2016

Camozzi’s reliabilityfor your productivity

News 2017

Product presentation

Control Pag

Series K8DV directly operated solenoid valves with separating diaphragm 4

Series K directly operated solenoid valves 6

Series 8 pneumatically and electropneumatically operated valves 8

Series VNR unidirectional cartridge valve 12

Series TC1-V 2/2-way shut-off micro-valve 14

Series AP directly operated proportional valves 16

Series CP directly operated proportional valves 24

Treatment Pag

Series TC1-R cartridge pressure regulator 30

Also this year Camozzi has enlarged its range with solutions that focus on increased

performance and productivity of the applications at its clients, maintaining a constant

quality level and assuring maximum reliability even in very complex conditions.

To this purpose, the Series K valves in the 2/2 version, the Series K8DV with

separating diaphragm, the new Series 8 cartridge valves, the Series AP valves with

proportional technology in the flanged version and revised CP version in the sizes 16

and 20 mm were developed in order to further optimize electric connections. Besides

the products above, we find the new Series TC1-V shut off micro-valve, the VNRC5

unidirectional cartridge valves and the new regulator TC1-R.

4

> VERY COMPACT DESIGN AND REDUCED WEIGHT

> HIGH FLOW PERFORMANCES

> VERY LOW INTERNAL VOLUME

> SUITABLE TO BE APPLIED IN MEDICAL EQUIPMENT AND ANALYTICAL INSTRUMENTS

Directly operated solenoid valveswith separating diaphragm

Series K8DV

The increasing demand for

miniaturized solenoid valves with

separating diaphragm and the

experience acquired during the

realization of the Series K8 served

to create this new series of models

with total fluid separation.

In fact, the new Series K8DV was

born to meet all the demands to

shut off aggressive or heat sensitive

fluids requested by the latest

technologies. Thanks to a separating

diaphragm, the fluid is isolated

from all internal metal parts of the

solenoid valve and avoids heating,

even if minimum, generated

by the solenoid positioned above.

The material of the diaphragm,

available in FKM, EPDM or FFKM

and the body in PEEK, enable this

solenoid valve to be used in a very

wide range of applications in the

medical, analytical, chemical and

pharmaceutical, biotechnological

and environmental sector.

Available in a cartridge version or

suitable to be mounted on a subbase

and thanks to its reduced dimensions,

it satisfies all installation needs of

portable or laboratory devices.

5

Generaldata

TECHNICAL SPECIFICATIONS

Function 2/2 NC

Operation directly operated with separating diaphragm

Pneumatic connections cartridge for manifold or flanged for subbase

Nominal diameter 0.7 mm

Kv (l/min) 0.1

Operating pressure 0 ÷ 2 bar

Operating temperature 5 ÷ 50°C

Fluid Liquids / aggressive or inert gases

Response times ON ≤ 10 ms - OFF ≤ 15 ms

Installation any position

MATERIALS IN CONTACT WITH FLUID

Body PEEK

Seals FKM - EPDM - FFKM

ELECTRICAL SPECIFICATIONS

Voltage 24 V DC - 12 V DC - 6 V DC - 5 V DC - 3 V DC - other voltages upon request

Voltage tolerance ±10%

Absorption 0.6 W

Duty cycle ED 100%

Electrical connection 2 Pins 0.5 x 0.5 Interaxis 4 mm

Protection class IP00

Codingexample

K8DV SERIES

C TYPE OF BODY:C = cartridge version - 0 = flanged version

00 NUMBER OF POSITIONS:00 = valve without housing

5 NUMBER OF WAYS - FUNCTIONS:5 = 2-way NC

0 SEAL MATERIAL: 0 = FKM - 4 = EPDM - 5 = FFKM

5 NOMINAL DIAMETER: 5 = 0.7 mm

G BODY MATERIAL: G = PEEK

2 ELECTRICAL CONNECTION: 2 = interface pin size 4 mm

3 SOLENOID VOLTAGES: 4 = 3V DC (0.6 W) - 5 = 5V DC (0.6 W) - 1 = 6V DC (0.6 W) - 2 = 12V DC (0.6 W) - 3 = 24V DC (0.6 W)

K8DV C 00 - 5 0 5 - G 2 3

Dimensions

2

1

NEWS 2017 | CONTROL > SERIES K8DV

6

Directly operated solenoid valvesSeries K 2/2-way

> COMPACT DESIGN

> HIGH PERFORMANCE

> SUITABLE FOR APPLICATIONS IN MEDICAL EQUIPMENT AND ANALYTICAL INSTRUMENTS

> VERSIONS AVAILABLE FOR USE WITH OXYGEN

From the Series K, already included

in our catalogue, a new range

of models has been developed with

only the 2-way NC function

and new flow characteristics.

The range of the orifices available

has been enlarged with diameters

from 0.6 up to 1.4 mm.

To guarantee a perfect integration

with the already existing range,

the same electrical connection

characteristics and the same

footprint were maintained in order to

have the inlet and outlet ports in the

same position of the 3-way models.

This enables to use solenoid valves

with 2-way and 3-way with common

inlets or outlets on the same manifold,

optimizing the processings of the flow

channels to intercept.

All models also have versions that are

suitable to be used with oxygen.

The procedures applied for the cleaning

of components, of assembly and of

packaging, are performed according

to the ASTM G93 standards.

7

Generaldata


Function 2/2 NC Operation directly operated with poppet Pneumatic connections on subbase by means of screwsNominal diameter 0.6 - 1.0 - 1.4 mm Kv (l/min) Ø 0.6 = 0.18 / Ø 1.0 = 0.4 / Ø 1.4 = 0.45 Operating pressure Ø 0.6 = 0 ÷ 6 bar / Ø 1.0 = 0 ÷ 3 bar / Ø 1.4 = 0 ÷ 2 barOperating temperature 0 ÷ 50°C Fluid filtered air class 5.4.4 according to ISO 8573-1 (viscosity oil max. 32 cSt), inert gasesResponse times ON <10 msec - OFF <10 msec Manual operation with monostable buttonInstallation any position


Body Technopolymer PBT Seals FKMInternal parts Stainless steel


Voltage 24 V DC - 12 V DC - 6 V DC - other voltages upon requestVoltage tolerance ±10% Absorption 1 W Duty cycle ED 100%Electrical connection connector - wires L = 300 mmProtection class IP50

Coding example

K SERIES

0 TYPE OF BODY:0 = single base (only M5) or interface - 1 = manifold

00 NUMBER OF POSITIONS:00 = interface - 01 = single base (only M5) - 02 ÷ 99 = N° of positions on manifold

1 NUMBER OF WAYS - FUNCTIONS:0 = manifold or single base - 1 = 2/2-way NC - 2 = 2/2-way NC electric part turned by 180°

0 PORTS: 0 = interface - 2 = M5 side outlets

5 NOMINAL DIAMETER: 2 = 0.60 mm - 5 = 1.00 mm - 7 = 1.40 mm

K MATERIALS: K = PBT body, HNBR poppet seal - F = PBT body, FKM poppet seal

2ELECTRICAL CONNECTION: 1 = 90° conn. with protection and led B = in-line conn. with protection and led F = wires (300 mm) with protection and led2 = 90° conn. with protection C = in-line conn. with protection G = wires (300 mm) with protection3 = 90° connection D = in-line connection H = wires (300 mm)

3 SOLENOID VOLTAGES: 1 = 6 VDC - 2 = 12 VDC - 3 = 24 VDC

MOUNTING: = standard to be mounted on plastic interface - M = with screws for mounting on metal interfaces (upon request)

VERSION: = not to be used for oxygen - OX1 = for use with oxygen (non volatile residual less than 550 mg/m²)OX1 = for use with oxygen (non volatile residual less than 33 mg/m²)

K 0 00 - 1 0 5 - K 2 3

Dimensions

2

1

NEWS 2017 | CONTROL > SERIES K

8

Pneumatically and electropneumatically operated valves

Series 8

> HIGH FLOW

> VERSIONS AVAILABLE FOR USE WITH OXYGEN

The Series 8 enlarges the range

of models available with the cartridge

valve directly integrated in an

anodized aluminium body comprising

also the pilot solenoid valve.

The new bodies enable to have

pneumatically operated models with

external pilot or electropneumatically

operated models with both external

and internal piloting.

The internal pilot takes the pressure

needed to activate the cartridge

valve directly from the main pressure

line, avoiding further pneumatic

connections. In this case, to guarantee

a correct operation, a minimum

pressure of 3 bar must be present.

In case it is necessary to activate

the cartridge valve with a pressure

less that 3 bar in the main line, it is

necessary to use models with external

piloting, making sure to guarantee

a pressure between 3 and 6 bar.

For the Normally Open function,

a continuous pneumatic piloting

must be guaranteed.

Besides different types of electrical

connections, all models also have

versions that are suitable to be used

with oxygen. The procedures applied

for the cleaning of components,

of assembly and of packaging, are

performed according to the ASTM G93

standards.

9


Function 2/2 NC - 2/2 NO - 3/2 NC - 3/2 NO

Operation pneumatic

Pneumatic connections Size 1 = G1/8 - Size 2 = G1/4 - Size 3 = G3/8

Nominal diameter Size 1 = 5.0 mm - Size 2 = 6.6 mm - Size 3 = 9 mm

Kv (l/min) Size 1 = 6.5 - Size 2 = 12.5 - Size 3 = 23

Flow (6 bar ∆P 1 bar) Size 1 = 420 l/min - Size 2 = 800 l/min - Size 3 = 1480 l/min

Operating pressure 0 ÷ 6 bar

External pilot pressure 3 ÷ 6 bar


Fluid filtered air class 5.4.4 according to ISO 8573-1 (viscosity oil max. 32 cSt), inert gases

Response times ON <10 msec - OFF <10 msec



Body Aluminium

Seals FKM

Internal parts Aluminium - Brass

Generaldata

pneumaticoperation

Generaldata

electropneumatic operation


Function 2/2 NC - 2/2 NO - 3/2 NC - 3/2 NO

Operation electropneumatic

Pneumatic connections Size 1 = G1/8 - Size 2 = G1/4 - Size 3 = G3/8

Nominal diameter Size 1 = 5.0 mm - Size 2 = 6.6 mm - Size 3 = 9 mm

Kv (l/min) Size 1 = 6.5 - Size 2 = 12.5 - Size 3 = 23

Flow (6 bar ∆P 1 bar) Size 1 = 420 l/min - Size 2 = 800 l/min - Size 3 = 1480 l/min

Operating pressure 3 ÷ 6 bar (0 ÷ 6 bar with external pilot)

External pilot pressure 3 ÷ 6 bar


Fluid filtered air class 5.4.4 according to ISO 8573-1 (viscosity oil max. 32 cSt), inert gases

Response times ON <10 msec - OFF <10 msec



Body Aluminium

Seals FKM

Internal parts Aluminium - Brass


Voltage 24 V DC – other voltages upon request

Voltage tolerance Size 1 = ±10% - Size 2 and 3 = -10% +15%

Absorption Size 1 = 1.3 W (acceleration) 0.25 W (maintenance) - Size 2 and 3 = 2 W

Duty cycle ED 100%

Electrical connection connector – wires L = 300 mm

Protection class Size 1 = IP50 - Size 2 and 3 = IP65 (with connector)

NEWS 2017 | CONTROL > SERIES 8

10

Dimensionselectropneumatic

operation

Coding example

8 SERIES

10 SIZE:10 = Size 1 - 20 = Size 2 - 30 = Size 3

C3 TYPE OF BODY:C3 = threaded body

4NUMBER OF WAYS - FUNCTIONS:1 = 2/2-WAY NC2 = 2/2-WAY NO4 = 3/2-WAY NC5 = 3/2-WAY NO

04PNEUMATIC CONNECTIONS:04 = G1/8” (Size 1)05 = G1/4” (Size 2)06 = G3/8” (Size 3)

F1NOMINAL DIAMETER:F1 = 5.0 mm (Size 1)G7 = 6.6 mm (Size 2)K1 = 9.0 mm (Size 3)

3 SEAL MATERIAL:3 = FKM

1 BODY MATERIAL:1 = aluminium

Y MANUAL OVERRIDE:N = not provided - Y = provided monostable

N MOUNTING ACCESSORIES:N = not provided

00OPTIONS:00 = no optionPP = pneumatic pilotPE = electropilot with external piloting

2C

ELECTRICAL CONNECTION:2C = connector type KN 90° + protection + led (Size 1)2F = connector type KN 90° in line + protection + led (Size 1)3A = DIN 43650 connector, form C, size 8 mm (Size 2 - 3)4A = DIN 43650 connector, form C, size 9.4 mm (Size 2 - 3)7A = L wires = 300 mm (Size 2 - 3)

C014

VOLTAGE - ABSORPTION:C012 = 12 V DC 1.3/0.25W (Size 1)C014 = 24 V DC 1.3/0.25W (Size 1)C020 = 12 V DC 2W (Size 2 - 3)C023 = 24 V DC 2W (Size 2 - 3)C025 = 48 V DC 2W (Size 2 - 3)

VERSION: = standardOX2 = for use with oxygen (non volatile residual less than 33 mg/m²)

8 10 C3 4 04 - F1 3 1 Y - N 00 2C C014


11

Dimensionselectropneumatic

operation

Mod. Function A B C D E F G H I L M N O P Q R S T U V Z Symbol

810C3404-F131Y-N002CC014 3/2 NC 31 71.5 16 11 10 20 16 34 33.8 52 17 8 23.9 47.5 3.2 6 G1/8 M3 6 - 10 EV54

810C3404-F131Y-NPE2CC014 3/2 NC 31 71.5 16 11 10 20 16 34 33.8 52 17 8 23.9 47.5 3.2 6 G1/8 M3 6 M5 10 EV56

820C3405-G731Y-NPE4AC023 3/2 NC 35 81 20 13 10 22 19.5 39.5 49 57 20 10 30 52.5 4.2 8 G1/4 M4 6.5 M5 15 EV56

820C3405-G731Y-N004AC023 3/2 NC 35 81 20 13 10 22 19.5 39.5 49 57 20 10 30 52.5 4.2 8 G1/4 M4 6.5 - 15 EV54

820C3505-G731Y-NPE4AC023 3/2 NO 35 81 20 13 10 22 19.5 39.5 49 57 20 10 30 52.5 4.2 8 G1/4 M4 6.5 M5 15 EV57

820C3505-G731Y-N004AC023 3/2 NO 35 81 20 13 10 22 19.5 39.5 49 57 20 10 30 52.5 4.2 8 G1/4 M4 6.5 - 15 EV58

830C3406-K131Y-NPE4AC023 3/2 NC 45 91 32 18 18 32 24 40 51.2 67 20.9 12 36 62.5 5.2 10 G3/8 M5 6 M5 15 EV56

830C3406-K131Y-N004AC023 3/2 NC 45 91 32 18 18 32 24 40 51.2 67 20.9 12 36 62.5 5.2 10 G3/8 M5 6 - 15 EV54

830C3506-K131Y-NPE4AC023 3/2 NO 45 91 32 18 18 32 24 40 51.2 67 20.9 12 36 62.5 5.2 10 G3/8 M5 6 M5 15 EV57

830C3506-K131Y-N004AC023 3/2 NO 45 91 32 18 18 32 24 40 51.2 67 20.9 12 36 62.5 5.2 10 G3/8 M5 6 - 15 EV58

Mod. Function A B C D E F G H I L M N O P Q R S T U V Z Symbol

810C3404-F131N-NPP 3/2 NC 31 - 16 11 10 20 16 34 - 52 17 8 23.9 47.5 3.2 6 G1/8 M3 6 - - YES1

820C3405-G731N-NPP 3/2 NC 35 - 20 13 10 22 19.5 39.5 - 57 20 10 30 52.5 4.2 8 G1/4 M4 6.5 M5 - YES1

830C3406-K131N-NPP 3/2 NC 45 - 32 18 18 32 24 40 - 67 20.9 12 36 62.5 5.2 10 G3/8 M5 6 M5 - YES1

Dimensionspneumaticoperation


12

Unidirectionalcartridge valve

Series VNR

> CARTRIDGE CONSTRUCTION PFOR USE IN A WIDE RANGE OF APPLICATIONS

> COMPACT DESIGN

> HIGH PERFORMANCE

> EASE OF INSTALLATION

> COMPATIBILITY BETWEEN MATERIALS USED AND SEVERAL GASEOUS FLUIDS

The cartridge construction of the

new Series VNR unidirectional valve

can be used in all those applications

and equipment where it is necessary

to include the single component in

personalized integrated pneumatic

circuits (manifolds) or collectors;

The compact design, in fact, allows

to be inserted and screwed in an

appropriate simple seat, in this way

simplifying installations. For its

construction, materials like

STAINLESS STEEL were selected

for the body and EPDM for the

tightenings in order to ensure full

compatibility with the most different

gaseous fluids.

13

Functioning This valve enables the passage of fluid from port 1 to port 2 and preventsthe flow in the opposite direction. The POPPET tightening elementguarantees two essential characteristics: to have a low minimum operating pressure and a high flow of gaseous fluid with minimum pressure losses.

Generaldata

Media Air, inert gases

Operating pressure up to 10 bar (145 psi)

Cracking pressure 0.05 bar (0.72 psi)

Operating pressure -5° ÷ +50°C

Materials in contact with the medium Stainless steel - EPDM

Orifice Ø 4 mm

Materials PARTS MATERIALS

1 Reduction Stainless steel

2 Body Stainless steel

3 Spring Stainless steel

4 Poppet EPDM

5 Cap Stainless steel

6 O-ring 10.5x1 EPDM

7 O-ring 6x1 EPDM

Dimensions

6

6

6

5

4

3

2

1

7

Coding example

VNR SERIES

C5 TYPE OF BODY: C5 = cartridge

00 PNEUMATIC CONNECTIONS: 00 = in manifold

E1 NOMINAL DIAMETER: E1 = 4.0 mm

4 SEAL MATERIAL: 4 = EPDM

3 BODY MATERIAL: 3 = stainless steel

OX2 VERSION: OX2 = for use with oxygen (non volatile residual less than 33 mg/m²)

VNR C5 00 - E1 4 3 - OX2

NEWS 2017 | CONTROL > SERIES VNR

M15x1

Ø12.4+0.1

0

0.8x45°

3.5

min

5

22.5

3.5

11 m

in

18 M

AX

Ø10 MAX

30°

30°

Ø13.2+0.1

0

SEAT

22.5

M15x1

ES.4

VALVE

14

2/2-way shut-off micro-valveSeries TC1-V

> COMPACT DESIGN AND REDUCED WEIGHT

> HIGH PERFORMANCE



The new Series TC1-V shut-off

micro-valve combines the drive

mechanism and the interception

mechanism in one single device.

Its principle is based on the actuation

of a poppet by means of an operating

pressure applied above it.

The poppet, once actuated, moves

away from the tightening seal,

permitting the flow of the intercepted

fluid. By removing the actuation

pressure, the poppet repositions itself

on the tightening seal by means of a

spring positioned below that closes

the flow of the fluid.

The new Series TC1-V shut-off micro-

valve has been studied to be used in all

applications and equipment where it is

necessary to insert the component in

integrated and customized pneumatic

circuits (manifolds) or collectors.

The cartridge design and its compact

dimensions enable this shut-off

micro-valve to be inserted in a special

seat that results in an easy installation

and a reduction of assembly times.

For its realization the most suitable

materials for contact with fluids were

selected. The body in PPS and the

FKM tightening seals guarantee full

compatibility with a wide range of

gaseous fluids.

15

Construction compact with preformed diaphragm

Ports G1/8 o 1/8 NPTF (only with the aluminium body version)

Mounting in line or cartridge (any position)

Operating temperature -5°C ÷ +50°C

Operating pressure 0 ÷ 10 bar (with pilot pressure 0.6 ÷ 10 bar)

Nominal flow 240 Nl/min (6 bar ∆P 1 bar)

Media air, inert/medical gases and oxygen

Generaldata

Materials PARTS MATERIALS

1 Base body Anodized aluminium

2 Lower spring Stainless steel

3 Insert PPS

4 Poppet Stainless steel

5 Body PPS

6 Intermediate body Anodized aluminium

7 Valve guide Polyamide

8 Diaphragm FKM

9 Bell Polyamide

Seals FKM

Dimensions

6

5

4

3

2

1

7

8

9

Coding example

TC SERIES

1 SIZE

V VALVE

36 CONSTRUCTION:36 = pneumatic command

C PORTS:C = cartridge - 1/8 = G 1/8 - 1/8TF = 1/8 NPTF

V SEAL MATERIAL:V = FKM

OX2VERSION:OX1 = for use with oxygen (non volatile residual less than 550 mg/m²)OX2 = for use with oxygen (non volatile residual less than 33 mg/m²)

TC 1 - V 36 - C - V - OX2

NEWS 2017 | CONTROL > SERIES TC1-V

16

Series APDirectly operatedproportional valvesSize 16 and 22 mm

Series AP directly operated 2/2-way

proportional solenoid valves, NC,

with nominal diameters range from

0.8 to 2.4 mm, can be used where

an open loop flow control is required,

with gas mixtures, to control

free flows or blows, or emptying

chambers using vacuum.

Series AP proportional valves have

been manufactured to optimize and

reduce friction and stick-slip effects.

The output flow is proportional to the

control signal.

As they can work also in vacuum,

a minimum working pressure is not

required.

> PWM OR CURRENT OPERATION

> OPEN LOOP FLOW CONTROL

> ALSO SUITABLE FOR USE WITH VACUUM

> SEVERAL VERSIONS AVAILABLE:

> WITH BODY IN PVDF (SIZE 16 mm ONLY)

> WITH REAR FLANGED BODIES

> WITH LOWER FLANGED BODIES

> SUITABLE FOR USE WITH OXYGEN

> SEALS IN FKM AND NBR

17

Function 2/2 NC

Operation proportional directly operated

Ports M5 - G1/8 - with rear flanges - with lower flanges

Hysteresis Size 16 mm: 12% FS - Size 22 mm: 10% FS

Repeatibility Size 16 mm: 7% FS - Size 22 mm: 7% FS


Mediumfiltered compressed air, unlubricated, according to ISO 8573-1 class 3.4.3, inert gas. All the valves are suitable for use with oxygen.


Materialsbody = brass / PVDF (size 16 mm only) seals = NBR and FKM

GP7 GPH U711 U712

Nominal resistance 193 ohm 48 ohm 85 ohm 22 ohm

Rated current 125 mA 250 mA 271 mA 542 mA

Generaldata

NOTE: Having a counterpressure on the outlet connection of at least 25% of the inlet pressure ensures the good functioning of the valve and improves its performance. Example: with inlet Pressure = 1 bar on the outlet connection, a min. counterpressure of 250 mbar is recommended.

Coding example

AP SERIES

7BODY: 6 = size 16 mm7 = size 22 mm

2 NUMBER OF WAYS: 2 = 2-way

1 VALVE FUNCTION: 1 = NC

1PORTS: 0 = M5 (size 16 mm only) 4 = with rear flanges 1 = G1/8 (size 22 mm only) 5 = with lower flangesL = male hose adaptor (for body in PVDF only, size 16 mm)

LNOMINAL DIAMETER: D = 0.8 mm (for size 16 mm only) L = 1.6 mm F = 1 mm N = 2 mm (for size 22 mm only) H = 1.2 mm Q = 2.4 mm (for size 22 mm only)

RSEAL MATERIAL: R = NBRW = FKM

2BODY MATERIAL: 2 = OT3 = PVDF (for size 16 mm only)

UENCAPSULATING MATERIAL: G = PA (for size 16 mm only)U = PET (for size 22 mm only)

7SOLENOID DIMENSIONS: P = 16x26 DIN EN 175301-803-C (for size 16 mm only)7 = 22x22 DIN 43650 B (for size 22 mm only)

11SOLENOID VOLTAGE: H = 12 V DC 3 W (for size 16 mm only) 11 = 24 V DC 6.5 W (for size 22 mm only) 7 = 24 V DC 3 W (for size 16 mm only) 12 = 12 V DC 6.5 W (for size 22 mm only)

OX2VERSION: OX2 = version with ASTM G93-03 Certification Level B (FKM seals only) = non-certified NBR version

NEWS 2017 | CONTROL > SERIES AP

AP - 7 2 1 1 - L R 2 - U 7 11 OX2

18

Flow diagrams

Size 16 mm

Nozzle 0.8 mm Q = Flow (Nl/min)I = Current (A)FS = Full scale

Nozzle 1 mm Q = Flow (Nl/min)I = Current (A)FS = Full scale




19

Flow diagrams

Size 22 mm







20

RESPONSE TIMES calculated according to the maximum flow at each operating pressure. [Electromechanical response time: 10 ms]

Size ø Pin [bar] Load response time [ms] Exhaust response time [ms]

0% - 10% 0% - 90% 10% - 90% 100% - 90% 100% - 10% 90% - 10%

16 mm 0.8 mm 10 12 43 31 11 39 28

16 mm 1 mm 8 12 42 30 11 38 27

16 mm 1.2 mm 6 10 41 31 11 41 30

16 mm 1.6 mm 4 10 40 30 11 40 29

22 mm 1 mm 10 10 36 26 10 36 26

22 mm 1.2 mm 8 10 45 35 12 38 26

22 mm 1.6 mm 6 12 45 33 12 40 28

22 mm 2 mm 5 12 42 30 11 34 26

22 mm 2.4 mm 4 11 45 34 12 44 32

Proportionalvalves

Size 16 mmwith lower flanges

Maximum flow according to the

inlet pressure


Size 22 mm Q = Flow (Nl/min) P = Inlet pressure (bar)


Q = FlowD.C. = Duty cycle

Hysteresisand

response times

21

2 1

Mod. Connection 1 Connection 2 Function Orifice ø (mm) Kv (l/min) Max pressure (bar) Max flow (Nl/min)

AP-6210-DR2-GP* M5 M5 2/2 NC 0.8 0.3 10 43

AP-6210-FR2-GP* M5 M5 2/2 NC 1 0.45 8 53

AP-6210-HR2-GP* M5 M5 2/2 NC 1.2 0.57 6 53

AP-6210-LR2-GP* M5 M5 2/2 NC 1.6 0.78 4 52

AP-6210-DW2-GP*OX2 M5 M5 2/2 NC 0.8 0.3 10 43

AP-6210-FW2-GP*OX2 M5 M5 2/2 NC 1 0.45 8 53

AP-6210-HW2-GP*OX2 M5 M5 2/2 NC 1.2 0.57 6 53

AP-6210-LW2-GP*OX2 M5 M5 2/2 NC 1.6 0.78 4 52

Mod. Function Orifice ø (mm) Kv (l/min) Max pressure (bar) Max flow (Nl/min)

AP-6215-DR2-GP* 2/2 NC 0.8 0.3 10 43

AP-6215-FR2-GP* 2/2 NC 1 0.45 8 53

AP-6215-HR2-GP* 2/2 NC 1.2 0.57 6 53

AP-6215-LR2-GP* 2/2 NC 1.6 0.78 4 52

AP-6215-DW2-GP*OX2 2/2 NC 0.8 0.3 10 43

AP-6215-FW2-GP*OX2 2/2 NC 1 0.45 8 53

AP-6215-HW2-GP*OX2 2/2 NC 1.2 0.57 6 53

AP-6215-LW2-GP*OX2 2/2 NC 1.6 0.78 4 52

Proportionalvalves

Size 16 mm

Proportionalvalves


2 1

* choose the desired voltage


For the use with vacuumconnect the line to connection 2.



22




AP-6214-DR2-GP* 2/2 NC 0.8 0.3 10 43

AP-6214-FR2-GP* 2/2 NC 1 0.45 8 53

AP-6214-HR2-GP* 2/2 NC 1.2 0.57 6 53

AP-6214-LR2-GP* 2/2 NC 1.6 0.78 4 52

AP-6214-DW2-GP*OX2 2/2 NC 0.8 0.3 10 43

AP-6214-FW2-GP*OX2 2/2 NC 1 0.45 8 53

AP-6214-HW2-GP*OX2 2/2 NC 1.2 0.57 6 53

AP-6214-LW2-GP*OX2 2/2 NC 1.6 0.78 4 52

Proportionalvalves

Size 16 mmwith rear flanges

Proportionalvalves

Size 22 mm

Proportionalvalves

Size 16 mmbody in PVDF

2

1


AP-7211-FR2-U7* G1/8 G1/8 2/2 NC 1 0.5 10 75

AP-7211-HR2-U7* G1/8 G1/8 2/2 NC 1.2 0.7 8 85

AP-7211-LR2-U7* G1/8 G1/8 2/2 NC 1.6 1.2 6 110

AP-7211-NR2-U7* G1/8 G1/8 2/2 NC 2 1.7 5 135

AP-7211-QR2-U7* G1/8 G1/8 2/2 NC 2.4 1.7 4 113

AP-7211-FW2-U7*OX2 G1/8 G1/8 2/2 NC 1 0.5 10 75

AP-7211-HW2-U7*OX2 G1/8 G1/8 2/2 NC 1.2 0.7 8 85

AP-7211-LW2-U7*OX2 G1/8 G1/8 2/2 NC 1.6 1.2 6 110

AP-7211-NW2-U7*OX2 G1/8 G1/8 2/2 NC 2 1.7 5 135

AP-7211-QW2-U7*OX2 G1/8 G1/8 2/2 NC 2.4 1.7 4 113

2 1 For the use with vacuumconnect the line to connection 2.



23



AP-7215-FR2-U7* 2/2 NC 1 0.5 10 75

AP-7215-HR2-U7* 2/2 NC 1.2 0.7 8 85

AP-7215-LR2-U7* 2/2 NC 1.6 1.2 6 110

AP-7215-NR2-U7* 2/2 NC 2 1.7 5 135

AP-7215-QR2-U7* 2/2 NC 2.4 1.7 4 113

AP-7215-FW2-U7*OX2 2/2 NC 1 0.5 10 75

AP-7215-HW2-U7*OX2 2/2 NC 1.2 0.7 8 85

AP-7215-LW2-U7*OX2 2/2 NC 1.6 1.2 6 110

AP-7215-NW2-U7*OX2 2/2 NC 2 1.7 5 135

AP-7215-QW2-U7*OX2 2/2 NC 2.4 1.7 4 113

Proportionalvalves

Size 16 mmbody in PVDF

Proportionalvalves


2 1


AP-621L-DR3-GP* Ø6 ** Ø6 ** 2/2 NC 0.8 0.3 10 43

AP-621L-FR3-GP* Ø6 ** Ø6 ** 2/2 NC 1 0.45 8 53

AP-621L-HR3-GP* Ø6 ** Ø6 ** 2/2 NC 1.2 0.57 6 53

AP-621L-LR3-GP* Ø6 ** Ø6 ** 2/2 NC 1.6 0.78 4 52

AP-621L-DW3-U7*OX2 Ø6 ** Ø6 ** 2/2 NC 0.8 0.3 10 43

AP-621L-FW3-U7*OX2 Ø6 ** Ø6 ** 2/2 NC 1 0.45 8 53

AP-621L-HW3-U7*OX2 Ø6 ** Ø6 ** 2/2 NC 1.2 0.57 6 53

AP-621L-LW3-U7*OX2 Ø6 ** Ø6 ** 2/2 NC 1.6 0.78 4 52

* choose the desired voltage ** pneumatic connection with tube and clamps

2 1




24

> HIGH FLOW

> GREAT PRECISION

> LOW HYSTERESIS

> HIGH WORKING DYNAMICS

> CARTRIDGE BODY FOR INSTALLATION IN REDUCED SPACE

Series CP directly operated

proportional valves can be used

where an open loop flow control is

required, with gas mixtures or to

control flows.

Series CP valves have been designed

to optimize dimensions and reduce

friction and stick-slip effects.

The output flow is proportional

to the control signal.

As they can work also in vacuum,

a minimum working pressure is not

required.

Their cartridge design makes them

particularly compact, thus they can be

mounted directly near the workstation.

Series CPDirectly operatedproportional valvesSize 16 and 20 mm

25

Generaldata

Size 16 mm

Generaldata

Size 20 mm

TECHNICAL FEATURES

Function 2/2 NC Operation proportional directly operatedPneumatic connections cartridgeNominal diameters 1 - 1.5 - 2 mmFree flow capacity 70 - 80 - 90 Nl/minOperating pressure 2.8 - 2 barMax overpressure 16 barLinearity 3% FSHysteresis 10% FSRepeatibility 5% FSOperating temperature 10°C ÷ 50°C

Media filtered compressed air, unlubricated, according to ISO 8573-1 class 3.4.3, inert gas. Also suitable for use with oxygen.


MATERIALS IN CONTACT WITH THE MEDIUM

Body brass, stainless steel, PPSSeals FKM

ELECTRICAL FEATURES

Operation PWM > 1000 Hz or current controlOperation voltage 6 - 12 - 24 V DCMax power consumption 2 WNominal resistance 11.8 - 37.6 - 184.7 OhmRated current 410 - 238 - 103 mADuty cycle 100%Electrical connection cable 300 mm AWG 24Protection class IP00 / IP40Average lifecycles 50000000Versions available on demand base with 1/8 - 1/4 ports

TECHNICAL FEATURES

Function 2/2 NC Operation proportional directly operatedPneumatic connections cartridgeNominal diameters 3 - 3.5 mmFree flow capacity 145 - 165 Nl/minOperating pressure 2.8 - 2 barMax overpressure 16 barLinearity 5% FSHysteresis 15% FSRepeatibility 5% FSOperating temperature 10°C ÷ 50°C

Media filtered compressed air, unlubricated, according to ISO 8573-1 class 3.4.3, inert gas. Also suitable for use with oxygen.


MATERIALS IN CONTACT WITH THE MEDIUM

Body brass, stainless steel, PPSSeals FKM

ELECTRICAL FEATURES

Operation PWM > 500 Hz or current controlOperation voltage 6 - 12 - 24 V DCMax power consumption 3.7 - 3 WNominal resistance 6.4 - 25.1 - 102.1 OhmRated current 615 - 313 - 154 mADuty cycle 100%Electrical connection cable 300 mm AWG 24Protection class IP00 / IP40Average lifecycles 50000000Versions available on demand base with 1/8 - 1/4 ports

NEWS 2017 | CONTROL > SERIES CP

26

Coding example

CP SERIES

CPORTS: C = cartridge S = subbase

6BODY: 6 = size 16 mm 7 = size 20 mm

2 NUMBER OF WAYS: 2 = 2-WAY

1 FUNCTION: 1 = NC

G

ORIFICE DIAMETRES: F = 1 mm (size 16 mm only) G = 1.5 mm (size 16 mm only) N = 2 mm (size 16 mm only) M = 3 mm (size 20 mm only) P = 3.5 mm (size 20 mm only)

W SEAL MATERIAL: W = FKM

2 BODY MATERIAL: 2 = brass

0 OVERMOULDING MATERIAL OF COIL: 0 = cartridge

PCOIL DIMENSIONS: P = ø 16 7 = ø 20

3

VOLTAGE: 1 = 6 V DC 3.1 W (size 16 mm only) 2 = 12 V DC 4.3 W (size 20 mm only) 3 = 24 V DC 3.1 W (size 16 mm only) 4 = 24 V DC 4.3 W (size 20 mm only) 5 = 12 V DC 3.1 W (size 16 mm only)

6 = 6 V DC 4.3 W (size 20 mm only) 7 = 6 V 4.8 W (only Ø 3.5, size 20 mm) 8 = 12 V 4.8 W (only Ø 3.5, size 20 mm)9 = 24 V 4.8 W (only Ø 3.5, size 20 mm)

CP - C 6 2 1 - G W 2 - 0 P 3


27

Flowdiagrams

Size 16 mm

Nominal diameter 3.5 mm Q = Flow (Nl/min) I = Current (A) P1 = Pressure in load (bar) P2 = 0 [free flow pressure] (bar) FS = Full scale

Nominal diameter 1 mm Q = Flow (Nl/min) I = Current (A) P1 = Pressure in load (bar) P2 = 0 [free flow pressure] (bar) FS = Full scale

Nominal diameter 1.5 mm Q = Flow (Nl/min) I = Current (A) P1 = Pressure in load (bar) P2 = 0 [free flow pressure] (bar) FS = Full scale




Flowdiagrams

Size 20 mm

28

Maximumpressure

according to theinlet pressure

RESPONSE TIMES calculated according to the maximum flow at each operating pressure. [Electromechanical response time: 10 ms]

Size ø Pin [bar] Load response time [ms] Exhaust response time [ms]

0% - 10% 0% - 90% 10% - 90% 100% - 90% 100% - 10% 90% - 10%

16 mm 1 mm 8 12 42 30 9 33 24

16 mm 1.5 mm 5 12 39 27 9 33 24

16 mm 2 mm 3 11 39 28 9 33 26

20 mm 3 mm 2.8 13 29 16 14 28.5 14.5

20 mm 3.5 mm 2 15 31 16 12.5 27.5 15




Isteresi e tempi di risposta

Q = FlowD.C. = Duty cycle

29

Mod. Orifices Ø (mm) Max operating pressure (bar) Max flow (Nl/min) Max flow Kv (l/min) Operation voltage (V DC) Max current (mA)

CP-C621-FW2-0P1 1 8 70 0.55 6 410

CP-C621-GW2-0P1 1.5 5 80 0.88 6 410

CP-C621-NW2-0P1 2 3 90 1.42 6 410

CP-C621-FW2-0P3 1 8 70 0.55 24 103

CP-C621-GW2-0P3 1.5 5 80 0.88 24 103

CP-C621-NW2-0P3 2 3 90 1.42 24 103

CP-C621-FW2-0P5 1 8 70 0.55 11 238

CP-C621-GW2-0P5 1.5 5 80 0.88 11 238

CP-C621-NW2-0P5 2 3 90 1.42 11 238

Solenoid valvesSize 16 mm

Solenoid valves Size 20 mm

Mod. Orifices Ø (mm) Max operating pressure (bar) Max flow (Nl/min) Max flow Kv (l/min) Operation voltage (V DC) Max current (mA)

CP-C721-MW2-072 3 2.8 150 2.8 6 615

CP-C721-MW2-074 3 2.8 150 2.8 12 313

CP-C721-MW2-076 3 2.8 150 2.8 24 154

CP-C721-PW2-072 3.5 2 130 3 6 615

CP-C721-PW2-074 3.5 2 130 3 12 313

CP-C721-PW2-076 3.5 2 130 3 24 154


30

Cartridge pressureregulator

Series TC1-R

> PORTS: CARTRIDGE CONSTRUCTION, G1/8 AND 1/8 NPTF

> FOR APPLICATIONS WITH OXYGEN, WITHOUT RELIEVING

> COMPACT DESIGN

> HIGH PERFORMANCE



The new Series TC pressure

regulator has been designed to be

used in all those applications and

equipment where it is necessary

to include the single component

in customized integrated pneumatic

circuits (manifolds) or collectors.

The cartridge construction

and the compact design allow

the regulator to be inserted

and screwed in an proper seat,

thus simplifying installations

and reducing assembly times.

For the creation of this new regulator,

materials have been analized and

chosen on the basis of their suitability

with the contact medium.

The body in PPS and the seals in

FKM thus ensure full compatibility

with a wide range of gaseous fluids.

31

Generaldata

Construction modular, compact wiht pre-formed diaphragm

Ports G1/8 (for version with aluminium body only)

Mounting in-line or cartridge (in any position)

Operating temperature -5°C ÷ +50°C

Inlet pressure 0 ÷ 10 bar

Outlet pressure 0 ÷ 0.5 bar; 0 ÷ 2 bar; 0 ÷ 3 bar; 0 ÷ 4 bar

Secondary pressure relieving No Relieving

Media oxygen, air and inert and medical gases

Repeatability ±0.2% FS

Materials

7

6

1

2

5

8

4

3

Coding example

TC SERIES

1 SIZE

R REGULATOR

3 WORKING PRESSURE:1 = 0 ÷ 0.5 bar 2 = 0 ÷ 2 bar 3 = 0 ÷ 3 bar 4 = 0 ÷ 4 bar

1 TYPE OF CONSTRUCTION: 1 = without relieving

C PORTS: C = cartridge 1/8 = G1/8 1/8TF = 1/8NPTF

V SEAL MATERIAL: V = FKM

OX2VERSION: OX1 = for use with oxygen (non volatile residual less than 550 mg/m²)OX2 = for use with oxygen (non volatile residual less than 33 mg/m²)

TC 1 - R 3 1 - C - V - OX2

PARTS MATERIALS

1 Base body Anodized aluminium

2 Lower spring Stainless steel

3 Insert PPS

4 Poppet Stainless steel

5 Body PPS

6 Valve guide PPS

7 Diaphragm FKM

8 Bell Polyamide

Seals FKM

NEWS 2017 | TREATMENT > SERIES TC1-R

32

Dimensionsof the seat

for cartridgeregulator

Dimensionsof the

regulator

with base bodycartridge


33

Flowdiagrams


Working pressure: 0 ÷ 2 bar

Pr = Regulated pressureQ = FlowPa = Inlet pressure



Working pressure: 0 ÷ 0.5 bar




34

present, face to face, able to look into

people’s eyes and speak their language.

This is why Camozzi now has an

international network, based in Italy,

but present on every continent.

To understand markets and the small

but important differences between

them, a company cannot only rely on

the essential digital tools we all use

every day, but it needs to be locally

PRESENCE ON EVERY CONTINENT

23 SUBSIDIARIES

55 EXCLUSIVE DISTRIBUTORS

6 PRODUCTION FACILITIES

OVER 1200 EMPLOYEES

SUBSIDIARIES AND PRODUCTION FACILITIES

COUNTRYWITH EXCLUSIVE DISTRIBUTORS

ITALY HEADQUARTERS CAMOZZI SPA

The Camozziworldwide networkTo respond and act quickly

C_Fluid. Your fluid solutions.

MIX

CO

MU

NIC

AZ

ION

E -

MI

93-1

500-

0GB

027

11/

2016

www.camozzi.comA Camozzi Group Company

Never Ending Innovation

C_Fluid Control Main contacts

[email protected] further information about our products and conditions of sale, contact Camozzi C_Fluid Control Division at:

Camozzi spaSocietà UnipersonaleVia Eritrea, 20/I25126 Brescia - ItalyTel. +39 030 37921 Fax +39 030 2400430

Technical assistanceCatalogue product inquiries and requests for support:Tel. +39 030 [email protected] product inquiries:Tel. +39 030 [email protected]

Worldwide sales network

Camozzi Subsidiaries and Exclusive DistributorsTo check our sales network, visit the Camozzi website atContacts / Camozzi Worldwide

Documents

News 2017 - Camozzi Pneumatics – USA – Fittings, … · news 2017 93-1500-0gb027 11/2016. ... > high flow performances > very low internal volume ... body peek seals fkm - epdm