New Harvest Metal Table · 2019. 3. 22. · Harvest Metal Table nstallation Packet Build Staging 1. Protect worksurface by clearing the build area of any debris that can cause damage

3430391900

Standing Height Table

Seated Height Table

Pour des instructions en francias, appelar le 800-822-7653Para instrucciones en enspanol, llame al 800-822-7653

Harvest Metal TableInstallation Instructions

03/22/2019

3430391900Page 2 of 14

Harvest Metal Table Installation Packet

#12 x 1” Wood Screw 5/16” - 18 X 7/8” Button head screw

black

#8 x 1/2” Wafer headscrew

1/4”-20 X 3/4” Truss head machine screw

5/16” Glide

3/4” wide galvanized steelLoop clamp

Plastic clip

Drill

No. 2 Phillips head screwdriver bit

No. 3 Phillips head screwdriver bit

Extra long Phillips head screwdriver bit

#2 Magnetic tip hex drive drill

1/4” driver

3/16” Hex Head Bit

Hardware - Total Quantities Shown

x32x40

x40

x2

x32

x4

x9

x9

x100

#10 x 1 Hex head Self drilling screw

Standing Height Tables1/4” - 20 x 3/4” Truss Head Screw - Bag #1

#12 - 8 Pan Head Screw - Bag #2

#10 - 16 x 1” Hex Head Self Drilling - Bag #3

#8 x 1/2” Wafer Head Screw - Bag #4

5/16” - 18 x 7/8” Button Head Screw -Bag #5

#10 x 7/8” Hex Head Screw

Seated Height Tables1/4” - 20 x 3/4” Truss Head Screw - Bag #1

#12 - 8 Pan Head Screw - Bag #2

#10 - 16 x 1” Hex Head Self Drilling - Bag #3

#8 x 1/2” Wafer Head Screw - Bag #4

#10 x 7/8” Hex Head Screw

#10 X 1-1/2” Philipswafer head

Hardware Bags

Tools

x40

#10 x 7/8”Hex Head Screw

Page 3 of 14 3430391900

Harvest Metal Table Installation PacketBuild Staging1. Protect worksurface by clearing the build area of any debris that can cause damage.

2. Place worksurafce upside down (as shown) on packing blankets or equivalent to protect upward facing show surface during the installation process.

3. Open up hardware pack and lay out the numbered bags within.

Build table with undersidefacing up.

Protect show surface and edges of the top

SCALE 0.500

SCALE 1.000

Note - Legs and corner brackets are left and right hand specific.

1. Attach corner brace to leg with (2) 1/4”-20 X 3/4” machine screws.

2. Align leg bracket with worksurface pilot holes. Start by installing (1) #12X1” wood screw into pilot hole #1. Verify that leg reveal is square with worksurface, make adjustments if needed. Install remaining 2 wood screws into pilot holes.

3. Repeat steps for all legs.

x8

x12

Leg Assembly

MachineScrews

Corner Brace

Pilot Holes

Hardware:

Leg RevealBoth Sides

3430391900Page 4 of 14

Harvest Metal Table Installation PacketStaging Electrical 1. Place all electrical components as shown below. Allow wiring to run through cord slots prior to center support channel being installed.

2. Power will run down one leg. Place cord/conduit through cord slots closest to preferred leg with plug/conduit hanging on the corner brace.

Cord Slots Electrical Boxes

1. Align center support channel across the length of the table shown in Illistration 1.

2. Install (3) #8-18X1/2” PHL Wafer screws through the corner brace into the support channel. Each channel is connected on both ends.

CenterSupport Channels

Corner Brace

Wafer screws

x12

Center Support Channels

Hardware:

Page 5 of 14 3430391900


1. Finish Installing leg assembly with (7) #12x1” wood screws into the workurface

2. Repeat for all legs.

x28

Hardware:

Note: Electrical must be moved aside to access all screw holes

Leg Assembly continued...

x8

Hardware:

Anti-Bow Brackets

CenterSupport Channel

Anti-BowBracket

6”

1. Mount anti-bow bracket into cavity of center support channels, and 6” away from each end.

2. Fasten each bracket to worksurface with (1) #12 x 1” wood screw. Repeat on both sides.

3. Mount remaining anti-bow brackets evenly across each support channel and attach to surface.

3430391900Page 6 of 14


SCALE 0.700

SCALE 0.550

Wood screwlocations

4. Align electrical module into the corner electrical bracket as shown. 5. Install (4) #12X1” wood screws to fully secure the corner unit.


1. With electrical box slid towards Center Support Channel, attach corner electrical bracket with (1) #12x1” wood screw into the front location circled below.

2. Slide electrical box forward and install (2) #12x1” remaining rear wood screws.


SCALE 0.550

Front Screw

SCALE 0.500

Corner electrical bracket

Electrical Box slid forward

Corner electrical bracket

x28

Hardware:

Corner Electrical

SlideBack

RearScrews

Page 7 of 14 3430391900


1. Align center electrical shroud with pilot holes in the center of the table. Attach using (2) #12 x 1” wood screws as shown below.

2. Mount center electrical box into shroud until fully seated. Attach module with (2) #8 x 1/2” Wafer head screws.

x4

Hardware:

x12

3. Place electrical cover plates between the center electrical box and shroud, keeping the back of the plates flush with center support channels.

4. Attach cover plates to electrical shroud with (4) #8 x 1/2” Wafer head screws

5. Repeat all steps for opposite side of table.

Center Electrical

Wafer HeadScrews

Electrical ShroudCenter

Electrical Box

ElectricalCover Plates

3430391900Page 8 of 14

Harvest Metal Table Installation PacketCenter Electrical Junction Box - Corded

Center Electrical Junction Box - Hardwired

1. Align junction box on the center of the worksurface, between the cord slots as shown below. Attach junction box with (2) #12 x 1” wood screws.

CenterCord Slots

x2

Hardware:

1. Align junction boxes in the center of the worksurface, as shown below. Attach to worksurface with (4) #12 X 1” wood screws.

Hardwired junctionboxes to be attachedby electrician.

x4

Hardware:

Page 9 of 14 3430391900

Harvest Metal Table Installation PacketExternal Stiffeners1. Place first stiffener along row of anti-bow brackets, with one end 2-5/8“ from the surface edge. Attach stiffener to surface with (2) #10 x 7/8 Hex head screws into outer-most holes of stiffener.

2. Place second stiffener along inside wall of fist stiffener, with end 2-5/8” from opposite surface edge than the first stiffener. Attach with (2) #10 x 7/8 Hex head screws into outer-most holes.

3. Finish installing external stiffeners with (16) #10 x 7/8 Hex head screws.

4. Repeat steps 1-3 for 2 remaining stiffeners on other half of worksurface.

x9

Hardware:

x9

5. Attach all cords/conduit to bottom of surface using (9) loop clamps and (9) #12 x 1” wood screws. Excess cords must be placed between external stiffeners.

x40

OutermostScrew

ExternalStiffener

ExcessCords

25/8

3430391900Page 10 of 14

Harvest Metal Table Installation PacketExternal Siffeners - 36” Wide VariantNote - The external stiffeners on 36” wide Harvest Tables differ from the standard mounting method.

Place largest stiffeners over top of Anti-bow Brackets. (Remove screws)

Place smallest stiffeners centered on the surface, 2 5/8” from each edge.

25/8

Page 11 of 14 3430391900


SCALE 0.500

SCALE 0.600

SCALE 0.520

SCALE 0.650

Shelves

1. Mount shelves into place over electrical and support channels. Route cord/conduit out of clearance notch of shelf next to chosen leg.

2. Align pilot holes in shelves with holes on the left and right hand corner electrical plates, as well as corner brace holes. Use (8) 1/4-20 x 3/4” zinc plated screws per shelf.

3. Attach shelf to center electrical with (4) 1/4-20 x 3/4” zinc plated screws per shelf.

1/4-20 x 3/4”zinc plated screws

Clearance Notch

#10 x 1-1/2”pan head screw

#10-16 x 1”Self-Drilling Screw

x24

x2

Hardware:

x36

Leave end screw out until next step

Shelves

4. Fasten center electrical to shelf using (1) #10 x 3/4” pan head screw per shelf.

5. Fasten shelves to support channels with #10-16 x 1” self-drilling screws. (Qty varies)

Corner Electrical Center Electrical

3430391900Page 12 of 14


1. Install leveling glides into threaded insert on each leg.

2. Attach foot rest to legs with (8) 5/16”-18 x 7/8” button head screws. Repeat for opposite end.

3. Place foot rail between foot rests and install (4) 5/16”-18 x 7/8” button head screws into each end. Repeat for remaining foot rail.

SCALE 0.500

Glide

1. Mount apron over shelves, install (2) #10 X 16 X 1” self-drilling screws into support channels.

2. Install (8) #8-18 x 1/2” PHL waferhead screws into shelves.

3. Repeat for opposite end.

x16

Hardware:

x4

5/16”-18 x 7/8”Button Head Screws

Foot Rail

Foot Rest

x32

Hardware:

SCALE 0.100

Reference view

x4

Apron

Aprons

SCALE 0.500

Foot Rest & Foot Rail (standing height only)

Foot Rest

Page 13 of 14 3430391900


1. Once fully assembled, lift and rotate the table to the upright position.

2. Check legs to make sure that they are perpendicular to the floor.

3. Level table.

Build view Stand view

WireManagement

Trough

1. Run cord/conduit from shelf through wire management trough.

2. Attach adhesive tape to trough on face shown below.

3. Adhere tape/trough directly to leg, keeping the outward facing surface flush with apron.

Top View

Apply adhesivetape to this surface

Flip Table Upright

*Important*Table should be rolled by at least two installers. Table should be lifted while flipping dueto the overall weight. Failure to adequately support table may result in damage to legs.

Wire Management Trough

This face to beflush with apron

3430391900Page 14 of 14


Final Assembled Table

Exploded View

Documents

New Harvest Metal Table · 2019. 3. 22. · Harvest Metal Table nstallation Packet Build Staging 1. Protect worksurface by clearing the build area of any debris that can cause damage