Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
Network Video Recorder
Quick Start Guide
1. Notes
● Please read this instruction carefully for correct use of the product and
preserve it for reference purposes.
● All the examples and pictures used here are for reference only.
● There may be several technically incorrect places or printing errors in
this manual. The updates will be added into the new version of this manual.
The contents of this manual are subject to change without notice.
● This device should be operated only from the type of power source indicated
on the marking label. The voltage of the power must be verified before using
the same.
Please check the device and the accessories after getting the device. If there are
any damages, shortages or defects, please contact your dealer immediately.
2. Packing Check
3. HDD Installation
The interfaces of the rear panel are for reference only.
4. Rear Panel Instruction
5. Startup & Shutdown
7. Network Configuration
You must configure the wizard if you start the NVR for the first time. You can
skip the settings of wizard next time. The default username is admin and the
password is set by yourself when you configure the wizard for the first time.
Click “Start” and select “Login”. This will take you to see a login box. Input
default username and password you set and you can see the live image.
►Startup
① Connect the monitor and the power.
② The device will boot and the power indicator will display blue.
③ A wizard window will pop up.
►Shutdown
Go to “Main Menu” and then select “Shutdown” icon. This will bring up a
shutdown window. The device will shut down by clicking “OK” button.
Then disconnect the power.
6. Login
After you finish adding IP cameras, you can see the live images through the
monitor of the NVR. The following will mainly introduce how to add the IP
cameras via LAN/WAN.
►LAN
① Set the network of the NVR. Go to Start → Settings → Network →TCP/IPv4.
Input IP address, subnet mask, gateway, etc. If using DHCP, please enable DHCP
in both the NVR and the router.
② Go to Start → Settings → Network → Port. Input HTTP port (the default
value is 80), server port (the default port is 6036).
③ The internal ethernet port is the port which connects all the PoE ports with
the NVR system. The PoE ports are available if the internal ethernet port is
online; if it is offline, all the PoE ports will be unavailable. The IP address and
subnet mask of the internal ethernet port can be changed to make the port in the
same network segment with the IP cameras which directly connect to the PoE
ports of the NVR.
Username
Password
admin
Login
Enter Password
Display Password Log In Automatically
LoginEdit Security Question Cancel
PortTCP/IPv4 DDNS E-mail NAT
IP Address Settings
Obtain an IP address automatically
Ethernet Port 1 ( Online ) Internal Ethernet Port 1 ( Online )
Obatin DNS server address automatically
IP Address IP Address
Preferred DNS
192 . 168 . 1 . 2 192 . 168 . 1 . 3
0 . 0 . 0 . 0 0 . 0 . 0 . 0
192 . 168 . 1 . 1
192 . 168 . 1 . 1
0 . 0 . 0 . 0
Subnet Mask Subnet Mask
Alternate DNS
Gateway
UPnP Network Status
④ Go to Start → Settings → Camera → Add Camera. The NVR will
automatically refresh the cameras searched. The IPC which supports the Onvif
protocol has be added manually. If the IPC searched is not in the same local
network as the NVR, you should select the device and click to modify the IP
address.
4.0.0.1.beta1
Version
1
2
192.168.1.20
192.168.1.38
XXX80
80
80
XXX
XXXXXX
3.4.2
3.4.2
255.255.255.0
255.255.255.0
No. IP Address EditPort Protocol ModelSubnet Mask
3 192.168.2.45 XXXXXX255.255.255.0
Quickly Add Manually Add
Add Camera
Selected: 1/3
AddDefault PasswordRemain Bandwidth: 108 / 120 Mb Cancel
Mac Address
IP Address
Port
CE :98 :23 :75 :35 :22
Edit IP Camera
9008
192 .168 . 1 . 45
255 . 255 . 255 . 0
admin
192 .168 . 1 . 1
Subnet Mask
Username
Gateway
Password
OK Cancel
AUDIO OUT
Internet
DC48VUSB LANHDMIVGAAUDIO IN
1
2
8
71
2
8
7
PoE Ports
This series of the product supports 1 SATA hard drive. Please make sure
that the device is powered off before the installation. The pictures of the
installation are only for reference, please take the real object as the standard.
① Loosen the screws to open the
cover.
② Put the screws into the HDD
but not tighten them.
③ Put the HDD onto the bottom of
the device.
④ Connect the power and data
cables.
⑤ Turn over the machine and secure
the HDD with the screws.
⑥ Install back the cover and secure
it with the screws.
Important: Please Take Note of this Password, Email and Secret question!
10. Manual Recording
8.UPnP
9. NAT
11. Playback
Display Password
IP Camera Name
IP Address
Model
Edit IP Camera
XXX
192 .168 . 1 . 58
9008
admin
XXX
Port
Username
Protocol
Password
IP Channel 5
OKTest Cancel
►WAN
① Set the network of the NVR. Go to Start → Settings → Network → TCP/IPv4. Input static IP address or enable PPPoE and then input the user name and password received from your ISP.
② Go to Start → Settings → Camera. Click “Add Camera” or behind the column of the search camera and select “Manually Add” to add the IP cameras. Input IP address, server port, username and password of the IP camera. The IP camera must be connected over WAN. And here the IP address of the IP cameramust be a WAN IP address.
►NAT Settings
① The NVR shall be powered on and connected to the network.
② Go to Start → Settings → Network → TCP/IPv4. You can obtain the IP address, subnet mask and gateway automatically. You can also manually enterthem according to the actual network situation. Please make sure the networksegment is the same as that of the network which is used.③ Set the preferred or alternative DNS Server. Click “Apply” to save theparameters.
④ Go to Start → Settings → Network → NAT tab. Enable NAT and select the NAT Server (The default NAT Server is nat.autonat.com ). Click“Apply” to save the parameters.
TCP/IPv4 Port UPnP NATDDNS E-mail Network Status
nat.autonat.comNAT Server
Enable
Apply
►NAT Access
After finishing the NAT settings, you can input http://www.autonat.com/n9000 in the IE address bar and then press enter to go to the following interface. Ifyou are the first time to access the NAT, you shall download and install theActiveX according to the popup tips. After installing ActiveX successfully,it will pop the login box.
Device Serial Number : Cinterface to check the serial number or go to Start → Settings → Network → Network Status to check the serial number of the NVR).User Name : The username of the NVR. The default username is admin .Password : The password of the NVR. The password is set by yourself when you configure the wizard for the first time.
lick on the menu bar at the bottom of the live
Before recording, please install and format a HDD. In the live interface you can see the menu toolbar. Click button to start recording and click it
again to stop recording. You can also click to check the status of the recording.
►Instant playbackClick “Instant Playback” in the right-click menu of the camera’s preview window to select or drag the playback progress bar to change the playback time to play back the record.
You can use the UPnP function to enable the fast connection of the device to WAN via a router without port mapping.
① Go to Start → Settings → Network → UPnP, and enable UPnP and thenclick “Apply” button to save.
② Enable the UPnP function in the router.
③ Click “Refresh” button to refresh the UPnP status. If the UPnP status werestill “Invalid UPnP” after refreshing it for several times, the port would be wrong.
HTTP Port
Server Port
80
6036
80183.17.254.19 Valid UPnP
Valid UPnP
Invalid UPnP
6036183.17.254.19
Port Type External Port External Address UPnP Status EditPort
RTSP Port 554 554
TCP/IPv4 Port UPnPDDNS E-mail NAT Network Status
AutoMap Type
UPnP
NAT
Enable
Refresh Apply
DeleteEdit
1
2
192.168.1.20[PoE1]IP Channel 1
[PoE2]IP Channel 2 192.168.1.38
XXX9008 XXXOnline
XXXOffline XXX9008
Remain Bandwidth: 85 / 120 Mb
No. Camera Name IP Address Port Protocol Model PreviewStatus
Edit Camera Edit Camera Group
Search Camera
3 192.168.1.45IP Channel 5 XXXOnline XXX9008
You may select the added device and click button to modify channel, IP address, ect.
⑤ Edit Camera”
Checkmark the device you want to add and then click “Add” button. The NVR will automatically refresh the cameras and return to “ interface. The IP cameras (with PoE function) which directly connect to the PoE port of the NVR will be displayed automatically in the camera list. The IP camera which connects to the PoE port cannot be deleted from the camera list manually. “Online” status means connecting the device successfully and you will see the live image.
Please change the mapping type to “Manual” and then click to modify the port until the UPnP status turns to “valid UPnP”.
Enter Password
Enter Password
Enter device serial number
Login
►General playbackClick on the tool bar at the bottom of the live preview interface or click Start → Playback to go to the playback interface as shown below. You can also add the playback cameras manually. Click in the playback window to pop up the “Add Camera” window. Check the cameras in the window and then click “Add” to add playback camera. The record files of the added playback camera will be played in the playback interface.