Nest Bed Leather Assembly Booklet...• Assemble bed as near as possible to final resting area. • Identify all parts and hardware before beginning assembly. • Retain packaging

WWW.DWR.COM | 1.800. 944 . 2233 | DES IGN WITH IN REACH STUD IOS 1

Nest Storage Bed in LeatherDesigned by Niels Bendtsen

Customer Service:

1.800.944.2233 inside the U.S.

1.203.614.0600 outside the U.S.

General Assembly Instructions

• Assembly requires two people and 1–2 hours.

• Assemble bed as near as possible to final resting area.

• Identify all parts and hardware before beginning assembly.

• Retain packaging until bed is fully assembled to ensure no

fittings or components are accidentally discarded.

• Make sure assembly area is clean and level.

Leather Care

• Do not expose leather to direct sunlight, which may cause drying

and fading.

• Do not expose leather to direct heat; keep it at least 12 inches

from heat sources.

• Do not sit on leather with wet or damp clothing.

• Take care when handling sharp objects near leather.

• Blot spills with a clean, dry cloth; never rub to remove spills or stains.

D

E

J

A

C

B

IHeadboardA

FootboardD

B Side railsC

KPlastic feetE

G Slat decksH

Headboard barI

Footboard barJ

Leather handleK

Slipcover (not illustrated)F

G

H

Wrench x 1

Medium bolt x 16M8 x 25mm (1")

Long bolt x 8M8 x 50mm (2")

Extra-long bolt x 4M8 x 70mm (2.75")

Nut x 14

Socket wrench x 1

Allen wrench x 2

Washer x 16

Short bolt x 3M8 x 17mm (5 / 8")



Customer Service:

1.800.944.2233 inside the U.S.

1.203.614.0600 outside the U.S.

Exterior Frame Checklist

Exterior Frame Hardware, Drawn Full Size

N

N Long support barsO

Short support barsM

Center footL

Storage panelsP

O

M

P

L

Short bolt x 3

Medium bolt x 12



Customer Service:

1.800.944.2233 inside the U.S.

1.203.614.0600 outside the U.S.

Interior Frame Checklist

Interior Frame Hardware, Drawn Full Size

C

B

A

Medium bolt x 8

4

C

B

D

Medium bolt x 8



Customer Service:

1.800.944.2233 inside the U.S.

1.203.614.0600 outside the U.S.

Attach footboard to side rails using medium bolts.

Be sure plastic caps in corner brackets are facing up.

2.

Attach side rails to headboard using medium bolts.

Be sure plastic caps in corner brackets are facing up.

1.

Image of bed frame flipping onto side.

E

E

E

E

WIDER CROSS BRACEOF CORNER BRACKET



Customer Service:

1.800.944.2233 inside the U.S.

1.203.614.0600 outside the U.S.

Turn bed frame assembly on its side. Screw feet into wider cross braces

of corner brackets, and tip bed frame assembly back down.

5.

F



Customer Service:

1.800.944.2233 inside the U.S.

1.203.614.0600 outside the U.S.

Loosely position slipcover over footboard and side rails. Beginning at

footboard, fi t slipcover snugly to corners, then remove fabric backing

from velcro a little at a time and press into place along top and bottom

edges of footboard. Repeat process along side rails working toward

the headboard. At headboard, join slipcover portions from side-rail

and headboard at corner and attach fi rmly with velcro.

6.

G

H

Extra-long bolt x 4Nut x 4 Washer x 8

G

H

G

H

Extra-long bolt x 4Nut x 4 Washer x 8



Customer Service:

1.800.944.2233 inside the U.S.

1.203.614.0600 outside the U.S.

Assemble mattress frame by placing slat decks side by side with

slats curving downward and flanged edges to the outsides. Secure

using extra-long bolts, nuts and washers as shown. Loosely tighten

in preparation for final tightening later.

7.

10

Long bolt x 4

Nut x 4

Washer x 4K

J

K

J

I

I

Long bolt x 4

Nut x 4

Washer x 4



Customer Service:

1.800.944.2233 inside the U.S.

1.203.614.0600 outside the U.S.

With slats still curving downward, locate and attach headboard bar

using long bolts, nuts and washers as shown.

8.

Attach footboard bar and leather handle to mattress frame

using long bolts, nuts and washers as shown. Install handle with

“Design Within Reach” facing outward and upside down.

9.

Medium bolt x 8



Customer Service:

1.800.944.2233 inside the U.S.

1.203.614.0600 outside the U.S.

With headboard bar, footboard bar and handle attached,

fi rmly tighten nuts and bolts holding mattress frame together.

10.

Flip mattress frame into position with slats curving upward, then

lower into bed frame as shown. Reaching between slats, attach hinge

assembly to side rails using medium bolts.

11.

Nut x 2

L

M

M

Short bolt x 2

Connect two short support bars to center foot using short bolts.14.



Customer Service:

1.800.944.2233 inside the U.S.

1.203.614.0600 outside the U.S.

With mattress frame raised and held up by assistant, attach

pistons to hinge assembly using nuts as shown.

13.

L / M

Medium bolt x 2



Customer Service:

1.800.944.2233 inside the U.S.

1.203.614.0600 outside the U.S.

Attach short-bar assembly to side rails using medium bolts.15.

NO

N O

Short bolt x 1

Medium bolt x 2

Join two long support bars at center foot and secure with short bolt.

Attach long support bars to footboard and headboard using medium bolts.

16.

P

P

P

P

Place storage panels inside, ensuring all sit fl at.

Mattress frame will not stay fully closed until fi tted with your mattress.

17.

Please Note



Customer Service:

1.800.944.2233 inside the U.S.

1.203.614.0600 outside the U.S.

Documents

Nest Bed Leather Assembly Booklet...• Assemble bed as near as possible to final resting area. • Identify all parts and hardware before beginning assembly. • Retain packaging