Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
The University of Manchester Research
NECKING BEHAVIOUR OF FLATTENED TUBULARBRAIDED COMPOSITES
Link to publication record in Manchester Research Explorer
Citation for published version (APA):Gautam, M., Potluri, V., & Ogin, S. (2015). NECKING BEHAVIOUR OF FLATTENED TUBULAR BRAIDEDCOMPOSITES. In 20th International Conference on Composite Materials [5]
Published in:20th International Conference on Composite Materials
Citing this paperPlease note that where the full-text provided on Manchester Research Explorer is the Author Accepted Manuscriptor Proof version this may differ from the final Published version. If citing, it is advised that you check and use thepublisher's definitive version.
General rightsCopyright and moral rights for the publications made accessible in the Research Explorer are retained by theauthors and/or other copyright owners and it is a condition of accessing publications that users recognise andabide by the legal requirements associated with these rights.
Takedown policyIf you believe that this document breaches copyright please refer to the University of Manchester’s TakedownProcedures [http://man.ac.uk/04Y6Bo] or contact [email protected] providingrelevant details, so we can investigate your claim.
Download date:27. Jun. 2021
https://www.research.manchester.ac.uk/portal/en/publications/necking-behaviour-of-flattened-tubular-braided-composites(12a54a8f-017d-40ae-bb89-b740afd8f11a).html/portal/prasad.potluri.htmlhttps://www.research.manchester.ac.uk/portal/en/publications/necking-behaviour-of-flattened-tubular-braided-composites(12a54a8f-017d-40ae-bb89-b740afd8f11a).htmlhttps://www.research.manchester.ac.uk/portal/en/publications/necking-behaviour-of-flattened-tubular-braided-composites(12a54a8f-017d-40ae-bb89-b740afd8f11a).html
20th International Conference on Composite Materials
Copenhagen, 19-24th July 2015
1
NECKING BEHAVIOUR OF FLATTENED TUBULAR BRAIDED
COMPOSITES
Mayank Gautam1, Prasad Potluri2, Stephen Ogin3, and Parshang Jain4
1Northwest Composite Centre, School of Materials, University of Manchester
Email: [email protected]
2Northwest Composite Centre, School of Materials, University of Manchester
Email: [email protected]
3Department of Mechanical Engineering Sciences, University of Surrey
Email: [email protected]
4School of Materials, University of Manchester,
Email: [email protected]
Keywords: Braid Angle, Biaxial, Triaxial, Necking, and Specific Energy Absorption
ABSTRACT
This paper presents results on the effect of braid angle and tow boundary conditions on the stress-strain
behaviour of carbon fibre and epoxy-based braided composites under tension for braid angles 350, 450
and 550. The specimens were produced by flattening the tubular braided sleeve during the preforming
stage. The braid angle and tow continuity have a significant effect upon the pseudo-plastic and necking
behaviour of the composites. Those specimens which showed extensive necking (all braid angles
without cut edges and the 550 braid angle with cut edges) produced approximately the same specific
energy absorption; specimens which showed either no, or very limited, pseudo-plasticity and necking,
had low values of specific energy absorption. The addition of axial tow insertions can provide
significant increases in the tensile mechanical properties (axial modulus and tensile strength) of the
composites with continuous fibres while retaining significant pseudo-plasticity.
1 INTRODUCTION
Braiding is a textile preforming technique that offers dimensional stability and near-net shaped
manufacturing capabilities, with the added advantage that braided composites often offer higher energy
absorption properties as compared to metals due to the ability of composites to undergo large
deformations (1). There is a need to design high performance and high energy absorbing materials and
structures for civil, military and aerospace applications that could avoid catastrophic failure (2). Braided
composites can exhibit higher energy absorption due to is multiple fibre fractures generated during the
crushing process (3) moreover due to their crashworthiness and greater production speeds they are now
being used now in automobile industry (4).The energy absorption and mechanical properties of braided
composites can be tailored by changing the braid angle; an increase in braid angle leads to an increase
in strain to failure and a decrease in stiffness (5). There been several studies reported in literature with
regard to effect of braid angle upon the energy absorption of both biaxial and triaxial tubular braided
composites under crushing mode (1, 6-8) showing an increase in energy absorption with an increase in
braid angle for biaxial braided tubes with the converse for triaxial braided tubes where lower braid
angles produce higher energy absorption.
While there have been several works reported in literature with respect to energy absorption properties
of braided composites under crushing mode there has been limited work reported in literature for
braided composites under tension. The work conducted in (9, 10) to determine the effect of tow
continuity for flat braided composites have reported for 45° braid angle where an increase in tensile
20th International Conference on Composite Materials
Copenhagen, 19-24th July 2015
2
strength of 20% and a decrease of energy absorption for cut edged specimen with no tow continuity in
comparison with uncut edged specimens with tow continuity. The study conducted in (11) on
performance of braided composites produced by flattening of biaxial braided sleeves for 25 and 45°
braided specimen reported higher tensile strength for 25° braided specimen and the effect of tow
continuity was determined to be significant where cut edged specimen depicted lower energy absorption
than an uncut edged specimen. The effect of axial tow insertion to produce triaxial tubular braided
composites have been studied in (12) where effect of axial tow insertion on axial modulus has been
reported to increase only upto 25° braid angle as the axial tows help in stiffening the structure in axial
direction.
This paper aims to study the energy absorption and mechanical performance of braided composites in
tension by varying braid angle, tow boundary conditions and effect of axial tow insertion.
2. EXPERIMENTAL METHODS
Figure 1 depicts process followed for the experimental method. In order to produce flattened braided
composites, cylindrical mandrel with diameter of 2.54 mm was overbraided using a 48 carrier braiding
machine at the University of Manchester. Commercially available carbon fibres T700 with 12000
filaments in a tow with individual filament diameter of 7 micro meter from Torayca were used for the
producing braided preforms. All 48 carriers were used to produce the braided sleeves leading to regular
braid topology (2/2) which implies a tow undulating over and under two tows.
During initial trials the biaxial braided sleeve could not be taken off the mandrel at higher braid angles
of 500 and 60°; however, at lower angles of 300 and 40°, the sleeve could be taken off in a stable tubular
state, but there were distortions in the braid angle along the length. Consequently, triaxial braids were
produced from which the axial tows were removed that helped in the removal of the braid without any
distortions. The probable reason for the stable removal of the braided sleeve using this technique could
be that once the axial tows are removed from the braid, gaps are created that help in loosening the tight
grip of the braid on the mandrel.
Figure 1: Process followed for producing continuous and discontinuous braided composite coupons.
20th International Conference on Composite Materials
Copenhagen, 19-24th July 2015
3
The braided specimens were taped tightly along the circumference at both ends while still on the
mandrel to secure the edges in order to make sure that the perimeter of the cross-section did not
change when the specimens were flattened. The tubular braided sleeve was flattened under 20N
uniform compression which caused a change in the braid angle; these changes were carefully recorded
and have been presented in Table 1.
Braid Angle
on mandrel
[⁰]
Braid Thickness
[mm]
Flattened Width
Secured Edges
[mm]
Braid Angle
On flattening with
secured edge
[⁰] 25 ± 0.7 1.6 ± 0.6 39.3 ± 0.1 29.6 ± 1.7
30 ± 0.8 1.7 ± 0.6 39.2 ± 0.2 35 ± 1.1
45 ± 1.2 1.8 ± 0.2 38.5 ± 0.5 45 ± 1.7
60 ± 0.3 2.1 ± 0.7 37.4 ± 0.6 55 ± 0.8
65 ± 0.9 2.2 ± 0.4 37.4 ± 0.8 60.7 ± 0.7
Table 1: Change in Braid Angle upon flattening tubular braided sleeve.
As observed in Table 1 the tubes with braid angles below 45° depict increase in braid angle of about 5°
however for tubular sleeve with braid angles greater than 45° a converse trend was observed where the
braid angle decreased by 5°. However a negligible change in braid angle was observed for 45° braid.
Such changes in braid angle when flattening a braided tubular sleeve have not been observed before
and further work is required to understand the phenomenon. Triaxial braids were also manufactured
using 6 and 12 axial tows inserted in a 450 braid, ensuring that the tows were equidistant from each
other and were taken off the mandrel without any distortion in the braid angle. In contrast, with biaxial
braids, the triaxial braids showed no change in braid angle from tubular to flattened state.
The flattened biaxial and triaxial braided sleeves were then infused using vacuum bag assisted resin
infusion with epoxy resin Araldite LY564. The resin-infused sleeves under vacuum were cured at 80°C
for 2 hours and post cured at 140°C for 8 hours. After infusion with resin and curing of the composites,
the change in braid angle observed from preform to cured state for all types of braids produced was
observed to be negligible. In order to determine the effect of braid angle, 5 specimens of each braid
angle of 35, 45 and 55⁰ were produced and tested. An additional 5 flattened braided sleeves were produced for each type of braid angle of 35, 45 and 55⁰ and tested with cut edges in order to determine the effect of tow continuity which upon curing were cut by 5mm along both edges containing four
interlaced tows. Five specimens of each type of triaxial braided specimens were also produced. The
tensile tests were carried out in accordance with ASTM D3158 (13).
Biaxial braided specimens have been labelled BC (braided continuous sleeve) and BDC (braided
discontinuous sleeve). BC and BDC are then followed by the braid angles of 35, 45 or 55 ⁰. The two types of triaxial braids produced were labelled BT0645 and BT1245, with the former implying 45
degree braided triaxial with 6 axial tows and the latter implying 45 degree braided triaxial with 12 axial
tows.
20th International Conference on Composite Materials
Copenhagen, 19-24th July 2015
4
3. RESULTS AND DISCUSSION
3.1. FIBRE VOLUME FRACTION AND CRIMP DETERMINATION
Five specimens of each type of braid were examined for their fibre volume content and the fibre volume
fraction values for three braid angles (350, 450 and 550) were 0.55, 0.54 and 0.54 as depicted in Table 2
respectively. ASTM D3171 (14) was used to determine the fibre content in the composite using
chemical digestion of the matrix. The crimp percentage was calculated as the ratio of the difference
between the undulated tow length and actual tow length without undulation to the actual tow length
without undulation multiplied by 100 (15). The crimp percentage values as depicted in Table 2 increases
with braid angle due to greater undulation which is because an increase in braid angle leads to an
increase of tow thickness which leads to a corresponding decrease in the tow width.
Specimen Type Laminate
Thickness
[mm]
Tow Width
[mm]
Tow
Thickness
[mm]
Fibre Volume
Fraction
Crimp
[%]
BC35 1.5 ± 0.1 2.8 ± 0.1 0.27 ± 0.02 0.55 ± 0.1 1.5 ± 0.5
BC45 1.7 ± 0.5 2.1 ± 0.1 0.39 ± 0.03 0.54 ± 0.4 3.5 ± 0.2
BC55 2.5 ± 0.1 2.0 ± 0.1 0.44 ± 0.03 0.54 ± 0.1 4.8 ± 0.3
BDC35 1.49 ± 0.7 2.8 ± 0.1 0.27 ± 0.02 0.55 ± 0.1 1.5 ± 0.5
BDC45 1.8 ± 0.1 2.1 ± 0.1 0.39 ± 0.03 0.54 ± 0.4 3.5 ± 0.2
BDC55 2.5 ± 0.3 2.0 ± 0.1 0.44 ± 0.03 0.54 ± 0.1 4.8 ± 0.3
BT0645 1.9 ± 0.4 1.9 ± 0.2 0.41 ± 0.01 0.55 ± 0.2 4.2 ± 0.04
BT1245 2.1 ± 0.3 1.9 ± 0.4 0.41 ± 0.04 0.56 ± 0.1 4.2 ± 0.1
Table 2 : Specimen specifications for biaxial and triaxial braided laminates
Figure 2: Optical images for braided composites along the fibre axis for (a) 35⁰, (b) 45⁰ and (c) 55⁰
The fibre volume content for triaxial specimen with 6 and 12 axial tows was found to be 0.55 and 0.56
which is a slight increase of 1.8 and 1.9% compared to biaxial braids at same braid angle of 45⁰ as the
Resin
Rich areas
20th International Conference on Composite Materials
Copenhagen, 19-24th July 2015
5
percentage of fibre increased by 12.5% and 25% by insertion of 6 and 12 axial tows. The triaxial
specimen depicted two types of crimp of 3.5% where triaxial tows were not present and 4.2% where
triaxial tows were present as depicted in Figure 3.
Figure 3: Optical micrographs for braided composites along the fibre axis for 45⁰ braided composite
for (a) Biaxial, (b) Triaxial braid.
3.2. TENSILE TEST RESULTS
Figure 4 shows typical nominal stress-nominal strain curves for the flattened braided tubes, with cut
and uncut edges, for the three braid angles. The effect of braid angle and tow continuity for biaxial
braids can be seen in Table 4. For both uncut and cut edged specimens, as the braid angle increased
from 35 to 55 ⁰, the axial strength (ultimate axial stress) and axial modulus decreased. Classic Laminate theory (CLT) was used to predict the modulus of the cross-ply composite laminate that uses properties
of unidirectional lamina as the base to describe the stress-strain relationship. The properties of
unidirectional lamina were calculated using the Halpin-Tsai equations (16, 17) and presented in the
Table 3.
Specimen
type 𝑽𝒇 𝑬𝟏𝟏
[GPa] 𝑬𝟐𝟐
[GPa] 𝑮𝟏𝟐
[GPa] 𝝂𝟏𝟐 𝝂𝟐𝟏
T700 - 230 - 17 0.27 -
LY564 - 2.6 - 0.9 0.25 -
35 0.55 127.6 8.6 2.6 0.25 0.01
45 0.54 125.3 8.4 2.5 0.25 0.01
55 0.54 125.3 8.4 2.5 0.25 0.01
Table 3: Material Properties and Theoretically Calculated Properties for Unidirectional laminate for
determining properties of cross-ply laminates using CLT.
The predicted axial moduli values are in reasonable agreement with the measured values for both the
cut and uncut specimens (BC and BDC) except for the 450 specimens where the measured moduli are
about 30 to 40% higher than the predicted moduli; the reasons for this difference are unclear at present.
The strain to failure values for both BC and BDC specimens increase with increasing braid angle. The
strain to failure for the 350 and 450 BC specimens is greater than for the BDC specimens. However, for
the 550 specimens, the strain to failure for the BDC specimens is much greater than for the BC
specimens, which relates to the failure mode. The yield stress observed for uncut edged specimens for
35 and 45° braid angles was observed to higher than the uncut edged specimens that had a premature
failure as compared to specimens with continuous edges; however the yield stress for cut and uncut
edges specimens for 55° braid was observed to be same.
20th International Conference on Composite Materials
Copenhagen, 19-24th July 2015
6
Specimen
Type
Axial
Modulus
[GPa]
Predicted
Axial
Modulus
[GPa]
Ultimate
Axial Stress
[MPa]
Yield
Stress
[MPa]
Strain to
failure
[%]
Specific
Energy
Absorption
[kJ/kg]
T700 230 - 4900 - 2.1 -
LY564 2.6 - 82 - 6.3 -
BC35 22 ±2 21.8 355 ± 40 253 ± 32 12 ± 2 18 ± 2
BC45 13 ± 2 9.6 167 ± 77 135 ± 10 18 ± 2 17± 2
BC55 7 ± 1 7.2 96 ± 8 54 ± 4 39 ± 2 14 ± 1
BDC35 22 ± 1 21.8 317 ± 65 172 ± 29 3 ± 1 3.5 ± 0.2
BDC45 14 ± 2 9.6 197 ± 29 104 ± 11 5 ± 1 5.1 ± 0.4
BDC55 8.2 ± 0.2 7.2 73 ± 11 54 ± 2 54 ± 5 15 ± 2
Table 4: Tensile Properties of Material and Tested specimens.
3.3. NECKING BEHAVIOUR
The stress-strain curves in Figure 4 show significant pseudo-plasticity for many of the specimens.
Video recording was carried out for each specimen during the test for macroscopic investigation of the
specimens undergoing deformation. For each angle, the BC and the BDC specimens show identical
stress-strain behavior initially. At 350, whereas the BDC specimens show very little non-linearity before
failure, the BC specimens show a peak in the stress-strain curve and significant pseudo-plasticity before
failure (about 7%). Similar behavior is seen at 450, with a pseudo-plastic strain region of about 12%
for the BC specimens. For the 550 angle, both the BC and BDC specimens show large regions of pseudo-
plasticity of about 35% for the BC specimens and 55% for the BDC specimens.
Figure 4: Stress versus strain curves for tested specimens.
20th International Conference on Composite Materials
Copenhagen, 19-24th July 2015
7
Figure 5: Biaxial Tested specimens with continuous edges (a) 35⁰, (b) 45⁰, and (c) 55⁰ braid angles.
Monitoring of the specimens in relation to the stress-strain behavior showed a necking phenomenon for
some specimens similar to the necking phenomenon which has been observed previously for braided
composite tubes (5). For the BC (i.e. uncut) specimens with braid angles of 350 and 450, the specimens
formed a stable neck in the middle of the coupons which propagated towards the gripped ends of the
specimens with increasing strain. As Figure 4 shows, the load fell for the 350 specimens as the neck
propagated, whereas the load was roughly constant for the 450 specimens. For the BDC (cut) specimens
with 350 and 450 angles, there was some slight necking followed by ply delamination and then specimen
fracture, with no extensive necking at all.
Figure 6: Biaxial Tested specimens with discontinuous edges (a) 35⁰, (b) 45⁰, and (c) 55⁰ braid
angles.
The 550 BC (uncut) specimens showed a similar necking phenomenon to the 350 and 450 specimens,
but with a higher strain to failure. Fractured biaxial tows can be observed in Figure 5 which shows
delamination of two layers at failure for three braid angles for uncut specimens which failed along the
fibre axis near the tabbing region with minor delamination at the edges. In contrast to all of the other
20th International Conference on Composite Materials
Copenhagen, 19-24th July 2015
8
specimens, the BDC (cut) 550 specimens failed by a process which consisted of early layer delamination
(strain of 0.03) at the edges of the specimen followed by necking of the individual plies which started
to develop at one end of the specimen and propagated towards the other end of the specimen. This
failure mode produced the highest strain to failure of all the specimens. The 35⁰ braided specimen with dis-continuous edges depicted failure in direction of fibre axis however 45 and 55⁰ braided specimen depicted the failure along the cross-section.
Figure 6 shows complete delamination of layers at all three braid angles investigated. It can be predicted
from the sequence of failure for the specimens which showed significant pseudo-plasticity. It was found
that matrix failure occurred first, followed by fibre/matrix debonding. The consequence of this
combination of failure modes enabled the fibers to reorientate and shear along the loading direction
until they reach a locking angle and then fracture. The locking angle was determined from image
analysis for the BC specimens with tow continuity. The image analysis revealed that for the BC
specimens, locking angles were 300, 350 and 400 for the braid angles of 350, 450 and 550, respectively
unlike in [4] where the all braided tubular specimens reached a specific locking angle and ruptured.
3.4. ENERGY ABSORPTION PROPERTIES OF BIAXIAL BRAIDS
The total specific energy absorption was calculated from the area under the stress strain curves. All of
the specimens which showed extensive necking to failure absorbed approximately the same specific
energy of about 16 kJ/kg. The BC (uncut) specimens values were between 18 and 14 kJ/kg (with the
350 specimens showing the highest value and the 550 specimens showing the lowest value) and the BDC
(cut) 550 specimen, which also showed extensive necking after delamination, absorbed about 15 kJ/kg.
By contrast, the specimens which failed with very little pseudo-plasticity (BDC35 and BDC45) had the
much lower specific energy absorption value of about 4 kJ/kg.
3.5. EFFECT OF AXIAL TOW INSERTION
To investigate the possibility of improving the axial properties of the flattened braided tubular
specimen whilst retaining the energy dissipation characteristics associated with the pseudo-plasticity
and the necking, triaxial braided 450 specimens were manufactured with axial tow insertions of 6 or
12 axial tows.
Figure 8 shows a comparison of typical stress-strain curves for the 450 specimens with and without the
tow insertions. Specimens with 12 axial tows show a significantly higher axial modulus and tensile
strength than the original 450 braided specimens, but a much lower strain to failure. The specimens
with 6 axial tows show a significantly improved modulus (compared to specimens without the axial
tows) and an improved tensile strength, whilst retaining significant pseudo-plasticity. The prediction
for axial modulus was carried out for triaxial braided specimens using Halpin-Tsai equations (16, 17).
While predicted axial modulus for specimen with 0 and 6 triaxial specimen showed lower values as
compared to tested specimens the predicted axial modulus for triaxial specimen with 12 axial tows
depicted higher values as compared to experimentally found values. A comparison of the mechanical
properties, including the specific energy absorption, is shown in Table 5. The cross-sections of the failed
specimens along the fibre axis are shown in Figure 9.
20th International Conference on Composite Materials
Copenhagen, 19-24th July 2015
9
(a)
(b)
Figure 7: Schematic representation of individual plies for a)[ +45/−45]𝑠 and b) [+45/0/−45]𝑠 used to predict axial modulus using CLT.
Specimen
Type
Axial
Modulus
[GPa]
Predicted
Axial
Modulus
[MPa]
Ultimate
Axial Stress
[MPa]
Yield
Stress
[MPa]
Strain to
failure
[%]
Specific
Energy
Absorption
[kJ/kg]
BC45 13 ± 2 9.6 167 ± 77 135 ± 10 18 ± 2 17 ± 2
BT0645 19 ± 2 17.3 195 ± 31 169 ± 35 8 ± 2 9 ± 3 BT1245 22 ± 1 26.4 249 ± 31 - 1.3 ± 0.7 1.8 ± 0.3
Table 5 : Comparison of mechanical properties of 450 specimens with and without axial tow
insertions.
-45
Layer 1 = 0.43 mm Layer 2 = 0.43 mm Layer 3 = 0.43 mm Layer 4 = 0.43 mm
+45 +45 -45
Layer 1 = 0.43 mm Layer 2 = 0.08 mm
Layer 3 = 0.43 mm Layer 5 = 0.03 mm Layer 4 = 0.43 mm
Layer 6 = 0.43 mm
0 +45
-45 +45 0
-45
20th International Conference on Composite Materials
Copenhagen, 19-24th July 2015
10
Figure 8: Stress versus strain curves for 450 specimens with and without axial tow insertions.
Figure 9: Triaxial Tested specimens for 45⁰ braided specimens with (a) 6 Triaxials and (b) 12
Triaxials
As observed in Table 5 the specimens with 12 axial tows did not depict any yielding while the specimens
with 6 and no axial tows depicted yielding. As a consequence of retaining some pseudo-plasticity, the
specific energy absorption of the 450 specimens with 6 inserted axial tows is about 60% of the value of
specimens without axial tows, with an approximately 50% higher axial modulus and an approximately
20% increase in tensile strength. The pseudo-plastic behavior was not observed for 45° specimen with
12 triaxial tows.
4. CONCLUDING REMARKS.
From the experimental work conducted, it can be inferred that braid angle and tow continuity have a
significant effect upon the tensile behaviour of flattened tubular braided composites with braid angles
in the range 350 to 550. The biaxial braided specimens with tow continuity throughout the length showed
higher axial strains to failure as a consequence of pseudo-plastic behaviour and necking compared to
specimens with cut edges (i.e. no tow continuity). However the increasing strain to failure values did
not contribute to an increase in specific energy absorption which was approximately the same for all
specimens. For 55° biaxial braided specimens with no tow continuity (i.e. cut edges), the axial moduli
and failure stresses were approximately the same as for the specimens with continuous edges for the
same braiding angle. However, no pseudo-plasticity was observed for the 350 and 450 braided angle
specimens, leading to a low specific energy absorption; for the 550 specimens, extensive delamination
enabled necking to occur in each layer of the composite which led to high values of both the strain to
failure and specific energy absorption. Consequently, these preliminary experiments have shown that
20th International Conference on Composite Materials
Copenhagen, 19-24th July 2015
11
triaxial braids incorporating axial insertions can provide a 50% increase in axial modulus and a 20%
increase in tensile strength, whilst still retaining 60% of the specific energy absorption through the
retention of significant pseudo-plasticity. However, when the number of axial insertions is too high, the
braided tubes do not show pseudo-plasticity giving lower specific energy absorption values.
ACKNOWLEDGEMENTS
This work was supported by the Engineering and Physical Sciences Research Council [grant number:
EP/IO33513/1], through the EPSRC Centre for Innovative Manufacturing in Composites (CIMComp).
REFERENCES
1. Hull D. A unified approach to progressive crushing of fibre-reinforced composite tubes. Composites Science and Technology. 1991;40(4):377-421.
2. Pizhong Qiao, Mijia Yang, Bobaru F. Impact Mechanics and High-Energy Absorbing Materials: Review. Journal of Aerospace Engineering. 2008;21(4):235–48.
3. Hamada H, Nakai A, Saito H, Sugimoto K, Okano M. Effect of the braiding angle on the energy absorption properties of a hybrid braided FRP tube. Proceedings of the Institution of Mechanical
Engineers, Part L: Journal of Materials: Design and Applications. 2005;219(1):59-66.
4. Beard S, Chang FK. Design of Braided Composites for Energy Absorption. Journal of Thermoplastic Composite Materials. 2002;15(1):3-12.
5. Harte A-M, Fleck N. On the mechanics of braided composites in tension. European Journal of Mechanics - A/Solids. 2000;19(2):259-75.
6. Inai R, Chirwa EC, Saito H, Uozumi T, Nakai A, Hamada H. Experimental investigation on the crushing properties of carbon fibre braided composite tubes. I J Crash. 2003;8(5):513-21.
7. Farley GL, Jones RM. Prediction of the energy-absorption capability of composite tubes. Journal of composite materials. 1992;26(3):388-404.
8. Chiu CH, Tsai KH, Huang WJ. Effects of Braiding Parameters on Energy Absorption Capability of Triaxially Braided Composite Tubes. Journal of Composite Materials. 1998;32(21):1964-83.
9. Shinyama Y, Hatsukade Y, Tanaka S, Takai Y, Aly-Hassan MS, Nakai a, et al. Prediction of Initiation Site of Destruction of Flat Braided Carbon Fiber Composites Using HTS-SQUID
Gradiometer. Physics Procedia. 2012;36:150-5.
10. Hatsukade Y, Shinyama Y, Yoshida K, Takai Y, Aly-hassan MS, Nakai A, et al. Nondestructive evaluation of ± 45 ° flat-braided carbon-fiber-reinforced polymers with carbon nanofibers using
HTS-SQUID gradiometer. Physica C Super Conductivity 2012:2-8.
11. Pickett AK, Fouinneteau MRC. Material characterisation and calibration of a meso-mechanical damage model for braid reinforced composites. Composites Part A: Applied Science and
Manufacturing. 2006;37(2):368-77.
12. Xu L, Kim SJ, Ong CH, Ha SK. Prediction of material properties of biaxial and triaxial braided textile composites. Journal of Composite Materials. 2012;46:2255-70.
13. ASTM. Standard Test Method for In-Plane Shear Response of Polymer Matrix Composite Materials by Tensile Test of a ± 45° Laminate. 2001.
14. ASTM. Standard Test Methods for Constituent Content of Composite Materials. 1999. 15. Behara B. HP. Woven Textile Structure: Theory and Applications. Cambridge: Woodhead
Publishing in Textiles; 2010.
16. D.Hull, T.W.Clyne. An Introduction to Composite Materials. Second ed: Cambridge University Press; 1996.
17. J.C.Halpin, S.W.Tsai. Environmental Factors in Composite Design. 1967.