NEC IPASOLINK 100 INTRODUCTION

Modem Board and Modem

On/OFF Switch

LCT LAN Connection

Port

Main Board

NEC Power cable

9-16 PDH Drop Cable

IPASOLINK 100 is a microwave radio transceiver with a high-performance carrier packet switch. This versatile transceiver is compatible with all low-speed to high-speed applications, as well as with LTE and WiMAX mobile systems. Its advanced switch functions and excellent performance can meet and surpass every specification. iPASOLINK 100E can be used in utilities application, digital TV systems, and Internet medium-speed and high-speed networks. iPASOLINK 100E's extremely compact IDU requires minimum

space and can be installed almost anywhere. Its lightweight compact ODU and small parabolic antenna also needs little installation space. Boasting the technology used to develop the industry-leading PASOLINK

series, the iPASOLINK 100E is the best solution for your packet network requirements

1-8 PDH Drop Cable

Introduction NEC IPASOLINK 100

NEC IPASOLINK 100

NEC IPASOLINK 100

High performance Packet Radio High spectrum efficiency QPSK to 256QAM adaptive modulation Carrier class Layer 2 switch function Various QoS and VLAN functions Easy deployment Minimum foot print Low power consumption Quick installation Easy maintenance Antenna direct mount High reliability Advanced error collection Ethernet ring protection Link aggregation (port redundant) Fan-less natural cooling Man-machine interface Browser based user interface with GUI. In-band NMS SNMP v1/v2c/v3 Frequencies 6, 7, 8, 10, 11, 13, 15, 18, 23, 26, 28, 32, 38,

and 42 GHz

Features:----

Commissioning Process of NEC IPASOLINK 100

Connect IDU LCT Port by LAN Cable.( Laptop LAN Configuration not Required) then Open Internet Explorer and enter default IP- 172.17.254.253. and get Following window

then Enter User name and Password

User Name Admin

Password 12345678

Default IP URL 172.17.254.253

After Enter User Name Password Login Complete Now ok

After Login window will appear

Now Start Configure IDU Click on Easy Set Wizard then Easy setup

Define Near End to Far End and Far to Near End IDClick on Set up and define Site Name or ID then Next ..

After define Site ID Click ok then process will complete and next window Modem Setup will automatic open where we define Planned frequency

MODEM SETUPIn MODEM Setup Click on Setup then define Planned Channel Spacing ,Modulation,

Radio Mode and Frequency then Next ..ok..

7MHZ

Modulation QPSK

High Cap.

Frequency

After Define Click Next..ok..Complete..ok

AMR Radio Mapping SetupAfter Modem Setup AMR/Radio Mapping Setup will Open .Here we Select QPSK then

Next

In New Setting QPSK ROW click 2,Generally you will get 1 defined. This is For Activate PDH Channel Port.. IF we define 2 or more if 1st Port will Faulty we can shift to Channel Port 2. on

both End we have to change PDH Port cable.. Then Next..

Then Click Next OK..OK AMR/Radio Mapping Setup will complete

Management SetupHere click on Cancel Otherwise For NMS define IP 192.168.0.1 Subnet

255.255.255.248 Default 192.168.0.0 but Uninor not required So Just Cancel..

Traffic Routing Click on E1/STM-1/Cross Connect setting then If you defined only one in AMR Mapping in

Service No. Just Put 1 or defined 2 in AMR put in Service no . 2 or in Protection in Drop Down Select Main Board left Side and Modem in right Side both Near and Far End. How many

Channels you want to select then choose 1 or 2 or 3.. then do OK.

Traffic Routing Here we can Select , Delete and ADD Recreate E1 Routing

Traffic RoutingIn Provisioining we can separate ADD ,Delete Traffic Routing as per requirement

Traffic Routing and Cable Color Code

NEC IPASOLINK Support 16 PDH Drop . 1-8 Cable Color code is Same 9-16 .if you select Channel No.1 So Both End (Near or Far) Select Same color code From Same Cable..

1-8 E1 Cable

9-16 E1 Cable

1-8 E1 DDF

Color Code Channel no. 1-8

Channel No 9-16

YELLOW GRAY--RED GRAY ONE NINE

YELLOW GREEN--RED GREEN TWO TEN

YELLOW ORANGE --RED ORANGE

THREE ELEVEN

YELLOW BLUE--RED BLUE FOUR TWELVE

TX RX

It will better to Trace From Main Board Connector if you are using Channel 1 color code will be yellow Gray-Red Gray in 1-8 Cable or Use LED to Find TX and Rx it may be Simultaneously in One DDF or

or beside DDF..In Pic. Shown 1 TX and 2 RX in Same DDF

RX Level Click Metering and See Tx Power Receive Level

SET TIME /DATEClick Equipment Utility and Check in Display PC Time ok.

E1 LoopGo to Maintenance Control then Loop Back Control and 3rd from top TDM Loop back Control

and Click on ON button as used channel 1 or 2 Now Check BSC End

E1 LoopAfter proper channel E1 Loop Click on Current Status then Refresh then Click on IDU Particular

E1 will show Normal if Loop ok. Here you can also find accurate Channel Cable Termination

Alarm in IDUClick on Current Status then Click on Refresh button and Check Active Alarm , Event

Log ,IDU and ODU Alarm

FAR END OpenClick on Opposite site Link select and OK Far End IP Open

FAR ENDFar End IP Show 172.18.0.52 again Put User ID and Password

User Name Admin

Password 12345678

FAR END OPEN

Conclusion:--

NEC IPASOLINK 100 Configuration Process:-- 1st Check IDU ODU Earthing and Power Connect LAN Cable in LCT Port Put IP 172.17.254.253 Put User IDAdmin (A should be Caps Only)and Password12345678 After Login Go to Easy Setup and Put Site ID as given For Both End Site ID (Near to Far and Far to Near on Both Sides) Put Frequency, Channel spacing ,Modulation Now AMR Mapping if you are taking Single E1 Just Click on QPSK and Set Right Side 1 If you want more E1 set 2 (For 2 E1) For Traffic routing go to Provisioning Add E1 and In protection Block 1st Select Main Board then Modem

in right side. Same Selection should be Near and Far End. Also if using Single E1 Select 1 on both Side then ok.

For E1 Color Coding use LED and Trace Cable from Main Board D Connector. In D connector inside Cable is 1-8 and outside will be 9-16 E1.. also on DDF Board somewhere TX and Rx will be simultaneously on same DDF or Some time TX will be one DDF and RX will be one DDF

To see RX Level go to Metering and Check Power and RX Level To see Internal Alarm in IDU Click on current Status and refresh and See Alarm in IDU or ODU For E1 loop Click Maintenance Control Loop Control and 3rd From Top Now On E1 Loop you can See it in

IDU Alarm Log . proper Channel E1 will be Normal if Loop will Correct To open far End Click on Opposite Side Link and put again Same User Name and Password. E1 Color Code and E1 Channel No. is Important to select. Same Channel For Same Color ..Thanks;Krishna kumarARA Zone