NCD-702 InstructionManual

Instruction Manual

Remark: Any information subject to change without further notice

NCD-702

IMPORTANT INFORMATION REQUIRED BY THE FCCThis device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1)this device may not cause harmful interference; and (2) this device must acceptany interference received, including interference that may cause undesirable operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential installation .

This equipment generates.uses and can radiate radio frequency energy and, if not installed andused in accordance with the instructions, may cause harmful interference to radio elevationreception, which can be determined by turning the equipment off and on. The user is encouragedto try to correct the interference by one or more of the following measures:

* Reorient or relocate the receiving antenna.

* Increase the separation between the equipment and receiver.

* Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.

* Consult the dealer or an experienced radio/TV technician for help.

7 Touch Screen LCD Display Motorized Slide DownFull Detachable PLL Electronic Tuning Stereo AM/FM Radio

Multimedia Player With Aux-in Jack And Bluetooth

”

7" TFT

OPEN

MIC U SB

-10

1 2

INT RDM

43

RPT +10

65

RELMUTEAPS

MODEAV IN

NCD-702

PDF created with FinePrint pdfFactory trial version http://www.pdffactory.com

http://www.pdffactory.com

!CAUTION

RISK OF ELECTRIC SHOCKDO NOT OPEN

!

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVECOVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFERSERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightening flash with arrowhead symbol, within an equilateral tr iangle, isintended to alert the user to the presence of uninsulated dangerous voltagewithin the products enclosure that may be of sufficient magnitude to constitutea risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert user tothe presence of important operating and maintenance (servicing) instructionsin the literature accompanying the appliance.

CLASS 1 LASER PRODUCT

Laser product symbol: located on the rear panel of the unit, indicate this player is a classlaser product, only use weak laser and no hazardous radiat ion outside of the uni t.

1.Read through this instruction manual before installation and use.2.Do not touch the power plug with wet hand.3.Switch off the main power when the unit is not in use. (Disconnect the power plug from

the power outlet when you do not intend to use the unit for a prolonged period of time.)Before moving the unit, remove the disc from the unit/ tray first.

4.Do not open the cover or touch any of the components exposed out of the unit, only forqualified technicians.

5.Do not expose the unit under direct sunlight or nearby objects that radiate heat to avoiddamage the uni t.

6.Do not place the unit in moist and humid conditions, which effect the pick-up of the unitlead to out of work.

7.Place the unit on a flat surface and ventilative condition. Please ensure the ventilationholes are not covered to avoid overheating and malfunction.

8.Clear the panel and case with soft dry cloth only, do not apply any kind of thinner,alcohol or sprays.

9.The apparatus shal l not be exposed to dripping or splashing and that no objects filledwith liquids, such as vases, shall be placed on the apparatus .

WARNING: TO REDUCE THERISK OF FIRE OR ELECTRICSHOCK, DO NOT EXPOSETHIS APPLIANCE TO RAIN ORMOISTURE.

PRECAUTION



1. Before Operation...........................................................................................31.1 Glossary................................................................................................ 31.2 Precautions............................................................................................31.3 Maintenance and Cleaning of Discs..........................................................41.4 Battery Information of the Remote Control.................................................41.5 The Remote Control Description...............................................................51.6 The Locations and Names of Controls on or in the Unit................................61.7 Wires Connection Description..................................................................71.8 Unit Installation.......................................................................................8

2. Common Operation........................................................................................9

3. Radio Operation...........................................................................................10

4. Disc, USB and MMC/SD Card Operation........................................................114.1 Load/unload Disc, USB or Card...............................................................114.2 Pause Playback.....................................................................................134.3 Stop Playback .......................................................................................134.4 Select Chapter/Track with the UP/DN or the >>|/|<< Buttons......................134.5 Select Chapter/Track with the Number Buttons.........................................134.6 Select Chapter/Track with the Root/PBC Menu.........................................134.7 Playback with Speed..............................................................................144.8 Playback with Slow Speed......................................................................144.9 Display Still Frame Step by Step.............................................................154.10 Playback Repeatedly...........................................................................154.10.1 One/All Repeat.................................................................................154.10.2 A-B Repeat.......................................................................................154.11 Playback in Scan Mode.........................................................................164.12 Playback from a specified Chapter/Track or a Specified Time...................164.13 Playback in Random.............................................................................164.14 Playback in Different View-Angle...........................................................164.15 Playback in Zoom Mode........................................................................164.16 Change the Caption Language..............................................................174.17 Change the Audio Language.................................................................174.18 Change the Video Signal System..........................................................174.19 Look over the Playback Status..............................................................174.20 Program Playback...............................................................................184.21 Playback IMAGE files..........................................................................184.22 Playback MP4 files..............................................................................194.23 ESP and Function..........................................................................194.24 The DVD System Menu Setup Operation................................................19* The Region Code.................................................................................23

5

. The Trouble Shooting................................................................................ ...26

7. Specification...............................................................................................27

Contents

ID3

. Blue Tooth Hand free System........................................................................24

6



1. Before Operation

1.1 Glossary

PBC (playback control)It is a kind of signal(menu) recorded in the disc with SVCD or VCD2.0format used for the playback control. For the discs contained PBC, It canplayback interactive software with the menu displayed on monitor screen.If the disc contain still images, it can playback high definition of still image.

TitleGenerally, the title is the important part of DVD disc. for example, thetheme part of movie is title 1, the part described how to make movie is title2, the cast is title 3, etc. Every title contain a serial number that is easy tolook up.

ChapterA title can be divided into several blocks, so that every block can be operatedas a unit, the unit is called chapter. The chapter contain a unit at least.

TrackIt is the biggest component of VCD. Generally, every song of karaoke discis a track.

1.2 Precautions

Safety1. Power Source: The unit should be connected to power supply only of

the type described in the operating instructions or as marked on the unit.2. The unit is designed for negative terminal of the battery which is

connected to the vehicle metal. Please confirm it before installation.3. Do not allow the speaker wires to be shorted together when the unit is

switched on. Otherwise it may overload or burn out the power amplifier.4. Do not install the detachable panel before connecting the wire.

1. Do not use this unit when water and moisture is near it.2. If moisture forms inside the Lens, it may not operate properly. To correct

this problem, wait about one hour for the moisture to evaporate.3. If the car interior is extremely hot, do not use the player until the car has

been driven for a while to cool off the interior.

Environment



1.3 Maintenance and Cleaning of Discs

Disc Maintenance

1. To h

1.

Do not use petrel, thinner. commercially cleaner or anti-static spray candamage the unit.

keep the disc clean, andle the disc by its edge, do not touch the discsurface of the play side.

2. Do not stick paper or tape on the disc. If there is glue (or analog) on thedisc surface, must wipe it up before using.

3. Do not expose the disc to direct sunlight, or nearby heat sources such ascaliduct, or leave it in a car parked in direct sunlight where there can be aconsiderable rise in temperature.

4. Put the disc inside disc case to keep temperature after finishing playback.

Before playing, wipe the disc with a clean lint. wipe the disc outwards fromthe disc center.

2.

Disc Cleaning

Fig.1 Fig.2 Fig.3

A

B

+ side up

1.4 Battery Information of the Remote Control

Replace Battery in the Remote Control

Note about the Battery of the Remote Control

:1.Before using the remote control for the first time, pull the insulating

sheet out of the remote control as the direction indicated by thearrow.(see fig.1)

2.Press the movable block hold as the direction indicated by the A arrow(See fig.2), then pull the battery holder out of the remote control asthe direction indicated by the B arrow(see fig.2).

3.Replace the old battery by a new battery with (+) polarity side upward.(See fig.3).

4.Insert the battery holder to the original position in remote control.(See fig.3).

:1.Lithium battery: CR 2025 3V.2.Battery Life: 6 months with normal use in normal room temperature.3.Improper use of battery may cause overheating or explosion, so that

Result in injury or fire .4.Battery leakage may cause damage to the remote control.5.Do not short the battery.6.Do not throw the battery into the fire.7.To avoid the risk of accident, keep the battery out of reach of children.

7. Specification

General Specification

Power Supply Requirement..................................................DC 12V

Dimensions(w x h x d)...........................................178 x 50 x 160mm

DVD Deck Specification

Format.....................................DVD/VCD/JPEG/MP4/MP3/WMA/CDVideo System....................NTSC/PAL/PAL-M/PAL-N/AUTO(optional)Audio System..............................................................24 bit/96KHzLoading System.......................................................... Auto LoadingMounting Angle.................................................................0 to +/-30

Video

Video Type...................................................................16:9 and 4:3Video Output level......................................Composite:1.0 0.2Vp-p

Load impedance: 75 ohmsHorizontal Resolution................................................................500

Audio

Audio Output(Analog audio)..........................................2.0 VrmsFrequency Response.............................20Hz ~ 20KHz(at 1KHz 0 dB)S/N Ratio(Audio)............................................. 90dBSeparation..............................................................................50dB

Radio

FM SectionFrequency range..............................................87.5MHz - 107.9MHzUsable sensitivity......................................................................3uVI.F Frequency....................................................................10.7MHz

AM SectionFrequency..........................................................530KHz - 1710KHz

Maximum Power Output.............25W x 4 (measured at DC 14.4 V)

Specification

Specification

(at 1KHz 0 dB)

Specification

±

≥

+0-1.0



1.5 The Remote Control Description

16. SEARCH BUTTON

17. RDM BUTTON

18. RPT BUTTON

19. SUBTITLE/REDIAL BUTTON

20. TITLE/PBC/PAIR BUTTON

21. ANGLE/ST/# BUTTON

22. ZOOM BUTTON

23. AUDIO BUTTON

24. CLK BUTTON

25. A-B BUTTON

26. INT BUTTON

27. EQ/OPEN BUTTON

28. LOC/SLOW-FWD/* BUTTON

29. MUTE BUTTON

30. STOP BUTTON

31. VOLUME- BUTTON

32. < BUTTON

33. OK BUTTON

34. VOLUME+ BUTTON

35. BAND AND P/N BUTTON

36. PROG BUTTON

37. OSD BUTTON

38. LOUD BUTTON

39. TEL BUTTON

1. TILT BUTTON

2. MENU BUTTON

3. POWER BUTTON

4. ^ BUTTON

5. >>| BUTTON

6. > BUTTON

7. |<</CLEAR BUTTON

8. v BUTTON

9. SEL BUTTON

12. 10+ BUTTON

13. SETUP BUTTON

14. MODE BUTTON

15. APS/HANG UP BUTTON

10. PLAY/PAUSE BUTTON

11. NUMBER(0~10,+10-10) BUTTONS

1

2

3

4

5

6

7

98

10

11

12

13

14

1516

1718

1920

2122

23

24

2526

27

28

29

3031

3233

34

35

393637 38

PROG

A-B

LOUDOSDTEL

PAIR REDIAL

APSSEARCH

#

ZOOM RPT

TITLE/PBCAUDIO

INT

SUBTITLE

RDM

LOC

SLOW_FWD

CLK

ST

0/109 10+

BANDEQ

4321

5-10

76 8+10

CLEAR

+

SEL

SETUP

0K

MU MODE MENU

PWR OPEN P/N

6. The Trouble Shooting

Please read the user ’s manual carefully before using the DVD player. If you have any troublesin using this player, try to solve the problems by the suggestions mentioned below. If you cannot remove the trouble af ter using all the suggestions, please contact the company or thetechnical service center authorized by us. For the sake of your safety, please do not open thecover and repair the player by yourself, if that, it may cause electric shock.

NO PICTURE, SOUND AND INDICATION* Ensure that the power switch is on.* Ensure that the wall inlet is ok.* Ensure that the power cord is not damaged or the fuse is not blown.* Ensure that the power plug is connected to the inlet tightly.

NO SOUND BUT HAVE PICTURE* Ensure that the player’s audio output has a good connection with monitor ’s audio input.* Check whether the audio connector is damaged.* Check whether you have turned down the volume.* Ensure that you have set the right AUDIO setup of the player.* Ensure that the audio is not under mute.

NO PICTURE BUT HAVE SOUND* Ensure that the player’s video output has a good connection with monitor ’s video input.* Ensure that you have turned your monitor to the AV input channel connecting to your player.* Check whether the video connector is damaged.* Ensure that you have set the right VIDEO settings of the player.

BLACK AND WHITE PICTURE OR SCREEN ROLLING* Ensure that you have set the right TV SYSTEM (e.g. PAL, NTSC) setting.

FLAWS OF PICTURE OR SOUND* Check whether the setting of AUDIO is right.* Check whether the disc is scratched or stained.* Check whether the AV connector and the output terminal is stained.* Check whether there is condensation inside the Lens. If so, leave the player off for an hour

or so, then try again.* Check whether the installation angle is less than 30 .

DISPLAY NO DISC OR BAD DISC* Ensure that you have put the disc on the tray.* Check whether the disc is put in the reverse side.* Check whether the disc is distorted.* Check whether the disc is stained or scratched badly.* Ensure that the disc format is compatible to the player.* Ensure that the temperature inside the car is not too high. If so, cool off till the ambient

temperature returns to normal.* Replace another disc to insert it into the disc compartment.

REMOTE CONTROL IS INSENSITIVE OR DOES NOT WORK* Check the batteries of remote control and make sure that they are to be powerful and

good conductivity.* Direct the remote control to the IR sensor of the player.* Check whether there are some obstacles between the remote control and IR sensor.

SOME FUNCTION BUTTONS DO NOT WORK* Turn off the power, then turn on again.* Reset the unit to zero, then turn on again.* Remove the front panel from the unit, then install it again and then turn on again.

THE RADIO DOES NOT WORK* Check whether the antenna cable is connected firmly. Or manually tune for a station.

°



1.6 The Locations and Names of Controls on or in the unit

1. OPEN button2. POWER/MUTE button3. Monitor4. AV IN socket5. Disc Slot6. USB Jack7. SD/MMC Card Slot8. MODE button9. VOL knob10. >>| button11. |<< button12. PLAY/PAUSE/1 button

13. INT/2 button14. RPT/3 button15. RDM/4 button16. - 10 / 5 button17. + 10 / 6 button18. BAND/TEL button19. APS/HANG UP button20. EJECT button21. RESET button22. Small LCD Screen23. IR Remote Sensor24. Microphone25. REL button

1

2

3

4 6

10

9

8

11 12 14 16 17

5

13

18

1519

2022

23 24

The Front Panel

The Front Facet after removing the front panel7 21

25

SD/MMC

4. In the connection status: the audio of mobile phone transfers to the car audio systemwhenever a dialling takes place or receiving a call.

5. Dialling when in connection status

5.1 Dial with the mobile phone directly.

5.2 Dial with remote control with the following procedures:

(1) Input telephone number with number buttons 0-9

* Short press CLEAR button to cancel the wrongly input number if necessary

(2) Short press TEL to execute the dialling.

5.3 To redial the last phone number dialled

Short press REDIAL button or tap the icon, It will dial the last phone number.

6. Accept/Reject/End Call

.1 During ringing, short press TEL button to accept the call

6.2 During ringing, short press HANG UP button to reject the call

6.3 During talking, short press HANG UP button to end the call

Note: During ringing, the phone number appears.

6

7. To transfer the audio of a file played by Mobile Phone to the Car Audio Player

In the connection status between the Bluetooth devices of the Car Audio Playerand a Mobile Phone, if the mobile phone can play audio or video files and supportA2DP, when the Mobile Phone plays an audio or video file(For some Mobile Phones,you must select Play by BT firstly), the audio of the playing file will be transferredto the Car Audio Player.

In A2DP mode, if the Bluetooth device of the Mobile Phone support AVRCP, thefunctions of the >>|, |<< , PLAY/PAUSE , EJECT, MUTE, EQ, LOUD, VOL and SELbuttons are the same as one in media mode(no fast forward/backward functions forthe >>|/|<< buttons). The other buttons available in media mode are not available.

APS

USB

AV IN

OPEN

MIC

654321

INT RPT RDM -10 +10MUTE REL

MODE



1.7 Wires Connection Description

The Description of the Wires Connection of the Wiring Connecting Socket 1

Note: Use the clip end of a Ground Line provided by manufacturer to connect the Fixing Screw Bolt, use another end of the GroundLine to connect the negative pole of the power source. Otherwise, the video on screen maybe flashes.

The Description of the Wires Connection

Description of Connecting the Parking Brake Line to the Parking Brake System Built in the Car

Parking brake

Parking brake switch(inside the car)

Parking brake line(Green)

To metallic body or chassis of the car

NOTE: after connecting the Parking Line, the video on the small monitor of the front panel will be display only after br aking the car.

The Description of the Wires Connection of the Wiring Connecting Socket 2

YELLOWMEMORY B+

BLACK(GND)

IGNITION SWITCHBLUE AUTO ANT

GREENWOOFER LINE OUT

RED

FRONT

REAR

RIGHTSP

FRONT WHITE

WHITE / BLACK

GREEN / BLACK VIOLET / BLACK

GRAY / BLACK

GRAY

VIOLETGREEN

REAR

LEFTSP

RED R

WHITE LFRONT RCA LINE OUT

FUSEDFILTERBOX 1A& 10 AFUSES

WIRING CONNECTING SOCKET 1

WIRING CONNECTING PLUG 1

NOTES:1. Only speakers with 4 ohms impedance may be used.2. Ensure that the blue auto antenna cable does not make contact

with any ground connection.

BLACK

GREYYELLOW

YELLOW VIDEO OUT LINES

PARKING LINEGREEN

REAR VIEW CAMERA

BLACKYELLOW

REAR RCA LINE

GREY

REVERSAL LINEWHITE

WHITE L

RED R

Fixing Screw Bolt Wiring Connecting Socket 1

Wiring Connecting Socket 2 Radio Antenna jackBlack Black

WIRING CONNECTING SOCKET 2

WIRING CONNECTING PLUG 2

BROWN

AUX IN

RED R

WHITE LYELLOW VIDEO

5. BLUE TOOTH HANDFREE SYSTEM

1. Enter Bluetooth modeWhen you use MODE button or Mode Menu to enterBluetooth mode, it will display Bluetooth interface asright.

In Bluetooth interface, the icons descriptions are asfollows:

: Tapping it can pop up AUDIO & VIDEO SETUP interface as one in page 10.: Tapping it can transfer audio between the Car Audio System and mobile

phone.: Tapping it can exit to Mode Menu.: Same as CLEAR button in Remote Control.: Same as + button in a mobile phone.

The other icons are same as ones in the front panel and Remote Control.

2. Pairing and connection

1) Turn on the Bluetooth mode of the mobile phone;

2) Select the item of Finding the Bluetooth Device and enter it. After finishing the finding,it will show the name of the Bluetooth Device if finding a Bluetooth Device. Select itand enter it, then it will show a interface that ask you to input a password, input thepassword 0000 and then enter it. Then it will tell you pair OK.

3) For some mobile phones, they can automatically connect with the BT device of thecar audio system after pairing is ok; for some mobile phones, they need to select thepaired BT device and press the CONNECTION button . When connection is ok, theLCD of the car audio system will show LINK OK.

* when pairing is failed, long press the PAIR button on the remote control to enterpairing mode, then the LCD will display PAIR START, then pair and connect withmobile phone again.

3. Use the mobile phone to do connection or disconnection

In the connection status, find the paired and connected Bluetooth Device, then pressthe disconnection button to do disconnection.

In the disconnection status, find the paired and disconnected Bluetooth Device, thenpress the connection button to do connection.

Bluetooth interface



1.8 UNIT INSTALLATION

INSTALLATION INSTRUCTIONS

TO BOOST UP THE CAPABILITY OFANTI-JAMMING, PLEASE FIX THEMETAL STRAP ON THE METALCONNECTED TO THE BOTTOMBRACKET OF THE CAR.METAL STRAP

DASH BOARD

SLIDING METAL HOUSING

TO DRAW THE CHASSIS OUT OFTHE SLIDING METAL HOUSING,INSERT THE LEFT AND RIGHT KEYPLATES INTO THE RIGHT POSITIONOF THE 2 SIDES OF CHASSIS.

PLASTIC TRIM OUT

UNIT CHASSIS

SELECT THE PROPER TABFOR FIXING THE SLIDINGMETAL HOUSING.

THE UNIT IS INSTALLED TO BE AN ANTI-THEFT ONE. THE CHASSISOF THE UNIT WEARS A SLIDING METAL HOUSING. PLEASE DO THECONNECTION OF THE POWER, SPEAKERS AND ANTENNA ACCORDINGTO THE REQUIREMENT OF THE INSTRUCTION BOOK , THEN INSTALLTHE SLIDING METAL HOUSING IN THE CAR AS FOLLOWS.

FRONT PANEL

* The Region Code

Q: Not begin to playback but to display REGION ERROR after inserting disc intodisc compartment. Why ?

A: Because the DVD player and disc has respective region code. If the region codesof them are not match with each other, the DVD player can not play the disc.

Appendix: The region code of DVD:

The Motion Picture Association of America (MPAA) divided the world into 6regions, and named every region a code, namely region code. The region codesand the countries or areas represented by the region codes as follows:

Region 1: America, Canada, East-Pacific Inlands;Region 2: Japan, West Europe, North Europe, Egypt, South Africa, Middle East;Region 3: Taiwan, Hong Kong, South Korea,

Thailand, indonesia, etc.;Region 4: Australia, New Zealand, Central South America, South Pacific Inlands;Region 5: Russia, Mongolia, Indian Peninsula, Middle Asia, East Europe, North

Korea, North Africa, North-west Asia etc.;Region 6: China mainland.

Basically, when a DVD movie disc for the version of region 6 was decided not toissue, we need to purchase another DVD player that can play the DVD movie discfor the version of non-region 6. In order to view this disc, viewer who does not havethe non-region 6 DVD player facilities will have to spend extra sum of money to buyit. The problems caused from the area code inconsistency between the disc and theDVD player has pushed for the production of Unlock-Version DVD player facilities,and some DVD disc sets allow user to modify the area codes for a limited number oftimes. But note that only the discs produced by the 8 biggest filmmaking companiesof America restrict so, they are not one of original DVD format. That is to say, theDVD movie discs not produced by

South-east Asian countries include

the 8 biggest filmmaking companies of Americawere not restricted by the rule of region code. Generally, they are calledFreeRegionCode discs or Full Region discs. The 8 biggest filmmaking companiesof America are as follows:

1. WarnerBros;2. Columbia;3. 20thCenturyFOX;4. Paramount;5. Universal;6. UA(UnitedArtist);7. MGM(MetroDogwynMayer);8. WaltDisney



2. Common Operation

1. To turn on/off the unitIn power off mode, short press the POWER button to turn on the unit.In power on mode, long press the POWER button on the front panel or shortpress the POWER button on the remote control to turn off the unit.

2. To slide the monitor of the Car Audio System out of/into the chassis

3. To select function mode

.

5. To mute soundPress the MUTE button on the remote control to turn on/off MUTE mode.pressing the POWER button on the front panel shortly also can turn on/off MUTEmode.

6.

After sliding the monitor into the chassis, pressing the CLK button can displayclock time on the small LCD.

7. To select a desired

. To turn on/off LOUD modePress the LOUD button to turn on/off LOUD mode.When turning on LOUD mode, it will enhance bass level immediately when bassis not enough.

9. To reset the playerWhen the monitor or the small LCD display wrongly or some buttons are notavailable or sound is distorted, press the REL button to detach the front panel fromthe main unit, then remove the front panel and press the RESET button torehabilitate the distorted program to zero.

Press the MODE button to select RADIO, DISC(After inserting a disc), USB(After inserting a USBstorage), CARD(After inserting a card) , AUX orBLUETOOTH mode.

During playback, tapping the icon after poppingup Keyboard interface can pop up Mode Menu asright. then tap one icon in it to select your desiredmode.

4 To adjust sound levelRotate the VOL knob on the front panel or press or hold the + or - button on theremote control to directly adjust the volume level.

To display clock timePress the CLK button to display clock time on the small monitor of the front panel.

EQ modePress the EQ button on the remote control to select one of the preset musicequalizer curves: POP, ROCK, CLAS, FLAT. The sound effect will be changed.

8

Shortly pressing the OPEN button on the front panel or long pressing the OPENbutton on the remote control can slide the monitor of the Car Audio System outof the chassis or slide it into the chassis.

Mode Menu

It is for adjusting the hue of the video output.

It is for adjusting the saturation of the video output.

It is for adjusting the sharpness of the video output.

It is for selecting your desired sound effect when there is not central speakerand sub-woofer. There are 3 mode: LT/RT, STEREO, VSS.LT/RT: When playing a disc with PRO LOGIC Dolby stereo effect, choose the

item, so it will output audio signal with vivid theatre effect.STEREO: If you choose the item, when outputting audio signal with 5.1 channels,

it will output the left and right channels of signal ; when outputting audio signalwith 2 channels, it will output the common 2 channels of stereo signal.

VSS: If you choose the item, when playing a disc recorded with 5.1 channels,the main channel speakers can output audio signal with VSS effect.

It is for selecting audio output modeLINE OUT: It can linearly compress the audio signal. So the volume level is lower.

You should select the item at night.RF REMOD: It can make the volume level higher. You should select it at daylight.

After selecting the compression mode of LINE OUT, set the item, so you canadjust the linear compression ratio. If you set it to be FULL, the Peak-to-Peakvalue of the audio signal is the minimum; if you set it to be OFF, the Peak-to-Peak value is the maximum.

It is for selecting a desired audio output mode for the left and right ways of signal.It is mainly for Karaoke of Ac3. There are 4 modes in all as follows:STEREO, MONO L, MONO R, MIX MONO.

HUE

SATURATION

SHARPNESS

4.24.5 SPEAKER SETUP

4.24.6 DIGITAL SETUP

OP MODE

DYNAMIC RANGE

DUAL MONO

DOWNMIX



10.To do general setupTo do general setup, f irst pop up Mode Menu ,then tap the icon in the Mode Menu to pop up GENERALSETUP interface as right.In the interface, select one of CLOCK SET, RDS MODE ,OSD LANG, RADIO FREQ and SENSE SET on the left sideby tapping them, then set them by tapping some icons onthe right side accordingly.

* SENSE SET is used to set the sensitivity of stopping autosearching for an available radio station. When you tap it,i t will ask you to input a password. The password is 19,after inputting it, you can set the item.

11.To do calibrationTo pop up Calibration interface during media playback, fi rstpress the STOP button , then press the ZOOM button, final ly press the ^ and v buttons in turn.In the interface, you can have calibration by accurately tapping the cross cursor.

1. Enter RADIO modeWhen you use MODE button or Mode Menu to enter RADIOmode, i t will display RADIO interface as right.

In RADIO interface, tapping the icon can enter ModeMenu; tapping the icon can turn on or off TFT display;tapping the icon can pop up AUDIO & VIDEO SETUPinterface as right; the other icons are same as ones in theunit panel or in the Remote Control.

In the AUDIO & VIDEO SETUP interface, you can adjustVOLUME, TREBLE, BASS, BALANCE, FADER, BRIGHT-NESS, CONTRAST, COLOR, HUE; you can also turn onor off DBAS, MBP, LOUD; you can stil l select your desiredtransparency mode(by STD) and EQ mode(by EQ); tappingthe icon can return back to the previous status.

2. BAND BUTTONIn RADIO mode, press the BAND button on the remote controller or on the front panel toselect your desired radio band of and AM2, and the word means whichband is selected will be displayed on the small monitor of the front panel.

3. TUNE/SEEK UP/DOWN BUTTONSIn RADIO mode:

1) Long press the >>|/ |<< button to automatically search up/down for a available station fromthe current frequency.

2) Briefly press the >>| / |<< button to manually search up or down with step by step for yourdesired station from the current frequency.

4. APS BUTTONIn RADIO mode:

1) When long pressing the APS button, the radio searches from the lowest frequency and checksthe signal strength level until 1 cycle search is finished. And then the 6 strongest stations arepreset to the corresponding preset number memory bank. The AS operation is implementedin the each bank of the selected band. When the AS operation is finished, i t will scan eachpreset station for 5 seconds in FM or AM band from M1 as briefly pressing APS button. After

3. Radio Operation

FM1, FM2, FM3, AM1

as in item 3

AUDIO & VIDEO SETUP interface

GENERAL SETUP

RADIO interface

This item is for selecting the language of the SYSTEM MENU and all operatingprompt interface displayed during playback.

This item is for selecting a audio language.

This item is for selecting a subtitle language.

This item is for selecting a disc menu language.

there is only ANALOG mode, i.e. SPDIF/OFF, not optional.

It is for selecting your desired basic music tone(from low to high).

4.24.2 LANGUAGE SETUP

OSD LANGUAGE

AUDIO LANG

SUBTITLE LANG

MENU LANG

4.24.3 AUDIO SETUP

AUDIO OUT

KEY

4.24.4 VIDEO SETUP

BRIGHTNESS

CONTRASTIt is for adjusting the brightness of the video output.

It is for adjusting the contrast of the video output.



finishing a circle of scanning , it will resume broadcasting on the M1.(It can store 3x6stations for FM and 2x6 stations for AM in all)

2) When briefly pressing the APS button, the radio will scan each preset station for 5seconds in FM or AM band from M1.

After finishing a circle of scanning, it will resume broadcasting on the M1.

NOTE: In FM band, FM1,FM2,FM3 is checked one at a time.In AM band, is checked one at a time.

5. PRESET STATION [ 1-6 ] BUTTONS

In RADIO mode:

1) To memorize the current frequency on the current band, long press any one of the sixpreset buttons (1-6) .

2) To recall the preset memory on the current band, press one of the preset buttons [1-6] .

6. STEREO/MONO BUTTON

Press the ST button on the remote controller to select the STEREO or MONO soundmode for FM band.

7. LOC BUTTON

1) In RADIO mode, when the signal of the distance radio station are very weak and thereceiving effect is bad during tuning, check whether there is the word LOC on LCD. Ifthere is the word LOC on LCD, press this button to turn off the LOC function, then tuneagain for the distance radio station;

2) In RADIO mode, when the signal of the local radio station are too strong to lead that theinterference to the receiving effect during tuning, press this button to turn on the LOCfunction to display the word LOC on LCD, then tune again for the local radio station.

AM1, AM2

To play files in a disc, insert the disc into the disc slot, then it will automatically play .

To unload the disc in the disc slot, press the EJECT button to eject disc in the discslot and then you can remove the disc.

USB

.1 Load/unload disc or USB

4. Disc and Operation

4

For the DVD System Menu, there are 6 setup pages in all. They display as follows:

4.24.1 SYSTEM SETUP

TV SYSTEM

TV TYPE

DEFAULT

This product supports output of various TV system.

If your TV set has only NTSC or PAL system, the screen will blink and becomecolorless when a wrong TV system is selected. In this case, press the N/P buttonto switch the right TV system to match the TV color system.

The setup item is for matching TV screen size.

4:3 PS: Choose the item when connecting a TV set with 4:3 screen. When playingthe pictures with 16:9 size, the left and right parts of the video will be cut out,and display in full screen.

4:3 LB: Choose the item when connecting a TV set with 4:3 screen. When playingthe pictures with 16:9 size, the top and bottom parts of the TV screen will beturned into a black square respectively.

16:9: Choose the item when connecting a TV set with 16:9 wide screen.

This item is for making all setup items change back to original status.



To play files in a USB or Card, insert the USB or Cardinto the USB jack or Card Slot(firstly detach the frontpanel and remove it), then it will automatically play.

To unload the USB in the USB jack, press the STOPbutton twice and then remove the USB.

To unload the Card in the Card Slot, press the STOPbutton twice and then push the card firstly and pull itout of the Card Slot.

: If the disc, USB or card includes folder(forMP3/WMA/MP4/JPEG files), after loading, it willdisplay a root as right. On the bottom side of the root,the icon is for audio files; the icon is forimage files; the icon is for Video files. If files ofthese 3 file sort does not exist, you can not movecursor onto the file sort icon.

: During playback, tapping the icon inthe root (for MP3/WMA/MP4/JPEG) or any place onthe screen (for CD/VCD/DVD/MP4/JPEG) can popup the keyboard interface as right.

: Tapping it can pop up Mode Menu.: Same as the corresponding buttons

on the Remote Control.: Same as the corresponding button on theRemote Control.: Same as the corresponding button on theRemote Control or on the front panel.: Same as the TITLE button on the RemoteControl (available only for DVD).: Tapping it can stop playback and pop up theroot.(exist only for MP4/JPEG)

: Tapping one of them can select next orprevious chapter/track.

: Tapping one of them can switch on betweenthe speed levels of fast backward or forward.: Tapping it can pop up the AUDIO interface ofthe SET Menu as right. In the interface, you canadjust the levels of VOLUME, BASS, TREBLE,BALANCE and FADER; can turn on or off LOUD,DBAS and MBP; can select your desired EQ mode.Tapping icon can pop up the TFT VIDEO inter-face of the SET Menu as right. In the interface,you can adjust the levels of BRIGHTNESS, CON-TRAST, COLOR and HUE; you can also adjustTransparency by tapping USER, STDY , BRIG,SOFT and SHAR.Tapping EXIT icon can exit the SET Menu.

* It supports to 1.1/2.0 version of USB and 8 GB SD CARD.

Remark

Remark

Root interface for MP3/WMA/MP4/JPEG

Keyboard interface-1

Keyboard interface-2

SET Menu-1

SET Menu-2

3. During JPEG playback, press one of the >/</^/v buttons to change the angle ofviewing picture that is displaying as follows:>: 90 deg cw; <: 90deg ccw; ^:UP<-->DOWN; v: LEFT<-->RIGHTDuring JPEG playback, press the PROG button to change the mode of refresh picture.During JPEG playback, press the STOP button to stop playing and return to the rootmenu.

* During JPEG playback, the following buttons are not available: SLOW-FWD,SUBTITLE, TITLE, ANGLE, AUDIO, RDM, INT and A-B.

* In JPEG mode,the other operations are same as ones in MP3/WMA mode.

1. The root menu is displayed on TV when beginning to switch on Mp4 mode, then it willautomatically play the first file.During playback, press the STOP button to stop playing and return to the root menu.

2. When displaying the root menu, press the direction buttons to select your desiredFOLDER ,file or file sort icon, then press the OK or PLAY button to open the FOLDER,open the files of the file sort icon or play the selected file.When displaying the root menu, you can also use the number buttons to select theserial number of the file and play the file.

* The ANGLE, PROG, RDM, INT and TITLE/PBC button are not valid.* The other functions are same as ones in DVD mode; but the RPT function is same as

one in MP3/WMA mode.

There is ESP function for all formats of discs.

In MP3/WMA mode, during playback, the information of the file name, folder name,will be scrolling on the LCD display. As long as the

current playing music contains relevant tag information in version 1.0/2.0format, the 3 items underlined above will be scrolling on the LCD display; otherwise,they will not.

1. Press the SETUP button on the remote control to access the DVD System Menu onthe monitor.

2. There are 6 setup pages in all for the System Menu. Press the > or < button to selectan desired setup page.

3. Press the ^ or v button to select an setup item in the selected setup page.4. Press the > button to enter the setup item. Then press the v or ^ button to select a

desired mode of the setup item, finally press the OK button to confirm it.

* Press the < button to return to the upper level.* Press the SETUP button again or use the direction buttons to highlight the item of the

EXIT SETUP and then press the OK button to exit the System Menu.

4.22 Playback MP4 files

4.23 ESP and Function

song s title, artist and album

4.24 The DVD System Menu Setup Operation

ID3

MP3 ID3



4.2 Pause Playback

4.3 Stop Playback

4.4 Select Chapter/Track with the >>| / |<< Button

4.5 Select Chapter/Track with the Number Buttons

4.6 Select Chapter/Track with the Root/PBC Menu (If the disc includes theroot/PBC menu)

In the state of DVD/VCD/CD/MP3/WMA playing, press the PAUSEbutton on IR remote control to pause the playback, press the PLAYbutton to resume normal playback.

In the state of DVD/VCD/MP3/WMA/CD playing, press the STOP buttononce to pause the playback, then press the PLAY button to resume the normalplayback; press the STOP button twice to full stop the playback, then pressthe PLAY button to start playback from the beginning of the first chapter/track.

Press the >>| / |<< button during playback to select the next or last chapter/track to playback.

Note: Press the >>|/|<< button multiple times to advance multiple chapters/tracks forward or backward.

In the state of DVD/VCD(PBC OFF)/MP3/WMA/CD playing, press one ofthe 1~9 and the 0/10 number buttons to directly select and play the 1st to10th track/chapter (the 0/10 button is used as the 10 button).

If you want to play the track/chapter that s serial number is bigger than 10,use the 10+, 1~9 and 0/10 button. For example 1, to play the 13th track/chapter, firstly press the 10+ button once, then press the 3 button. Forexample 2, to play the 34th track/chapter, firstly press the 10+ button for 3times, then press the 4 button.(the 0/10 button is used as the 0 button)

Note: long pressing the +10 or -10 button can play the next 10 or last 10chapter/track(only for MP3/WMA).

In the state of DVD playing

1. Press the TITLE button on the remote control to display the title list.

It allows you to enter the order in which you want some chapters/tracks inDVD/VCD/MP3/WMA/CD to play.

1 During playback, press the PROG button to enter a program interface asfollows:

for DVD for VCD/MP3/WMA/CD

2 Use the direction buttons to move cursor onto the desired place for inputtingthe sequence number.

3 Use the number button to input desired sequence number of title/chapter/track with desired sequence.

4 Use the direction button to move cursor onto Play item, then press the OKbutton to play the programmed titles/chapters/tracks in programmed order;only pressing the PLAY button also can play the programmed titles/chapters/tracks in programmed order.

* To exit program playback, firstly press the STOP button, then press the PLAYbutton to enter sequence playback; or press the PROG button twice again.

* To remove the all programmed sequence numbers, move the cursor ontoClear item, then press the OK button.

* To change the programmed sequence, move the cursor onto the item youwant to change, input the desired sequence number.

* During VCD playback, if it is in PBC ON mode, at the same time of enteringthe state of program playback, it turns off PBC mode.

1. The root menu is displayed on the monitor when beginning to switch on IMAGEmode. .In the root menu, the left file sort icon is for MP3/WMA file; the middle fi le sorticon is for JPEG file; the right file sort icon is for VIDEO file. If one of these 3file sort does not exist, you can not move cursor onto the file sort icon.

2. When displaying the root menu, press the direction buttons to select yourdesired FOLDER, file or file sort icon, then press the OK or PLAY button toopen the FOLDER, or play the selected file, or play only this sort of file.When displaying the root menu, you can also use the number buttons toselect the serial number of the file and play the file.When you select the JPEG file sort icon, press the ^ or > button to select thefirst JPEG file, then press the v button to select the desired JPEG file, finallypress the OK or PLAY/PAUSE button to display the JPEG picture in full screenfrom the selected JPEG picture.

4.20 Program Playback

4.21 Playback IMAGE files



2. Press the direction buttons to select your desired title, and then press the OKor PLAY button to open the root menu of the selected title.

3. Press the direction buttons to select your desired chapter, finally press theOK or PLAY button to play the selected chapter.

During playback, pressing the MENU button can directly display the rootmenu of the title that is playing.

In VCD mode

1. When starting to turn on the PBC function, it will play from the beginning ofthe disc till it display the PBC menu on TV screen if the disc include the PBCmenu.

2. Press the number buttons to select your desired track to play.

In MP3/WMA mode

1. The root menu is displayed on the monitor screen all the time(and the TITLEor MENU button is not available).

2. Press the direction buttons to select your desired FOLDER, then press theOK or PLAY button to open the FOLDER, and then press the direction buttonsto select your desired file, finally press the OK button to play the selected file.

In CD mode, the TITLE, PBC, MENU buttons are disabled.

During normal playback, long press the >>|/|<< button continuously to fastforwards or backwards at the following speeds: x2, x4, x8, x20, normal.

During speed playback, press the PLAY button to resume normal playback.

During playback , press the SLOW_FWD button to execute the Slow Forwardfunction.

With each consecutive pressing of the SLOW_FWD button, the playbackspeed decreases. The speed levels in Slow Forward as follows:x1/2,x1/3,x1/4,x1/5,x1/6,x1/7,normal.

4.7 Playback with Speed

4.8 Playback with Slow Speed

ZOOMx2,ZOOMx3,ZOOMx4,ZOOMx1/2,ZOOMx1/3,ZOOMx1/4,ZOOM OFF.Press one of the ^/v/>/< buttons to select the area you want to enlarge.

In the state of DVD playing, press the SUBTITLE button repeatedly toselect the language of the caption or turn off the caption.(depend on themedia used.)In the state of VCD/MP3/WMA/CD playing, the button is not available.

1. In the state of DVD playing, press the AUDIO button repeatedlyon the IR remote control to select the desired language type.(depend on the media used)

2. In the state of VCD playing, press the AUDIO button repeatedly toselect the sound mode of the MONO L, MONO R, MIX MONO and Stereo,no language function.

3. In the state of CD/WMA/MP3 playing, the AUDIO button is invalid.

During playback of DVD/VCD , press the BAND(P/N) button on the frontpanel or on the remote control repeatedly to change the VIDEO SIGNALSYSTEM mode .

time of the playing chapter,the remained time of the playing chapter, the elapsedthe remained time of the playing title,

2. In the state of VCD/CD playing, press the OSD button repeatedly on theremote control to turn on/off the playback status. When it is on, it willdisplay the information such as: the serial number of the playing track, theelapsed time of the playing track, the remained time of the playing track, theelapsted time of the disc, the remained time of the disc.

3. In the state of MP3/WMA playing, press the OSD button repeatedly onthe remote control to turn on/off the playback status. When it is on, it willdisplay the information such as: the serial number of the playing track, theelapsed time of the playing track, the remained time of the playing track.

4.16 Change the Caption Language

4.17 Change the Audio Language

4.18 Change the Video Signal System

4.19 Look over the Playback Status

1. In the state of DVD playing, press the OSD button repeatedly on theremote control to turn on/off the playback status. When it is on, it willdisplay the information such as: the serial number of the playing title, theserial number of the playing chapter, the elapsed

time of the playing title,etc.



During slow forward, press the PLAY button to resume normal playback.The function is only for video.

If the unit is currently playing video, press the TEL button consecutivelyto display still frame step by step.Press the PLAY button to resume normal playback.

1. In the mode of DVD playback:Press the RPT button to select REP CHAPTER, REP TITLE, REP ALLor REP OFF.

2. In the mode of VCD(PBC OFF)/CD playback:press the RPT button to select REP ONE, REP ALL or OFF.

When it is in the state of PBC ON, during VCD disc playing, the RPTbutton are not available.

3. In the mode of MP3/WMA playback:Press the RPT button to select REP ONE, REP DIR, REP ALL or OFF.

Press the button if you want to repeat a specific segment on a discthat you define:

1. Press the button at a point (A) where you want it to be the start pointof the repeat segment. Press the button again at a point (B) where youwant it to be the terminal point of the repeat segment. Then it will play thesegment repeatedly.

2. To cancel the A-B repeat mode and resume normal playback, press thebutton for the third time.

4.9 Display still frame step by step

4.10 Playback Repeatedly

4.10.1 ONE/ALL Repeat

4.10.2 A-B Repeat

A-B

A-BA-B

A-B

Note:During VCD/MP3/WMA/CD playback, points A and B must be within thesame track.During DVD playback, points A and B can be selected from different chapters.

4.11 Playback in Scan Mode

4.12 Playback from a specified chapter/track or a specified time

4.13 Playback in Random

4.14 Playback in Different View-Angle

4.15 Playback in Zoom Mode

1. In the state of VCD(PBC OFF)/CD playing, press the INT button to playthe previous seconds part of each track on the disc. Press the INT buttonagain to resume normal playback.

2. In the state of DVD/MP3/WMA playing, the INT button is not available.

1. In the state of DVD playing, press the SEARCH button to display ainterface and highlight the title item, then use the number buttons to inputthe serial number of the title; use the direction buttons to highlight the chapteritem, then use the number buttons to input the serial number of the chapter;you can still use the direction buttons to highlight the time item, then use thenumber buttons to input the desired time to start playback; finally press theOK or PLAY button to play the selected chapter or play from the selected time.

2. In the state of VCD/MP3/WMA/CD playing, press the SEARCH button todisplay a interface and highlight the track item, then use the number buttonsto input the serial number of the track; you can still use the direction buttonsto highlight the time item, then use the number buttons to input the desiredtime to start playback; finally press the OK or PLAY button to play the selectedtrack or play from the selected time.

In the state of DVD/VCD(PBC OFF)/MP3/WMA/CD playing, press theRDM button to switch between RANDOM (ON)/RANDOM OFF. When inRANDOM (ON) mode, it will play in random.

1. In the state of VCD/MP3/WMA/CD playing, the VIEW-ANGLE button onthe IR remote control is not available.

2. In the state of DVD playing, press the VIEW-ANGLE button repeatedlyon the IR remote control to view in different angle.(This function is onlyfor the DVD media with ANGLE function)

In video/image mode, during playback, press the ZOOM button continuouslyto enlarge a certain area of the images on the screen with these multiples:

15



Documents

NCD-702 InstructionManual