Upload
omar-yamil-sanchez-torres
View
245
Download
4
Tags:
Embed Size (px)
Citation preview
Natural and Forced Convection Experiment
INME 42361
Table of Contents
Principle 3
Objective 3
Background 3
Newton’s law of cooling 3
Experimental Setup 5
Description of the Equipment: 5
Useful Data 6
Procedure 7
1. Free convection experiments 7
o Observations 7
o Analysis of results 7
o Comparison to theoretical correlations 8
2. Forced convection experiments 9
o Observations 9
o Analysis of results 9
o Comparison to theoretical correlations 9
3. Procedure for transient experiments 10
Tasks Required for Steady State Experiments 11
Tasks Required for Transient Experiments 11
INME 42362
University of Puerto RicoMayagüez Campus
Department of Mechanical Engineering
INME 4236 - Thermal Sciences Laboratory
Natural And Forced Convection Experiment
Principle
This experiment is designed to illustrate Newton’s law of cooling by convection
and to understand how the heat transfer coefficient is obtained experimentally. Natural
and forced convection over a heated cylinder is analyzed and experimental results are
compared with standard correlations.
Objectives
1. Determine the heat transfer coefficient for flow around a cylinder under free and
forced convection.
2. Understand the correlation between Nu, Reynolds and Rayleigh numbers.
3. Compare with standard correlations from textbooks on heat transfer.
4. Determine the effect of thermal radiation for both natural and forced convection.
5. Study the transient temperature response of a solid object as it cools due to
natural or forced convection.
Background
Newton’s Law of Cooling
For convective heat transfer, the rate equation is known as Newton’s law of
cooling and is expressed as:
)( ∞−=′′ TThq s
INME 42363
Where Ts is the surface temperature, T∞ the fluid temperature, h is the convection heat
transfer coefficient and q” is the convective heat flux. The heat transfer coefficient h is a
function of the fluid flow, so, it is influenced by the surface geometry, the fluid motion in
the boundary layer and the fluid properties as well.
The normalized momentum and energy equations for a boundary layer can be
expressed as follows,
2*
*2
*
*
*
**
*
**
Re
1
y
U
x
P
y
UV
x
UU
L ∂∂+
∂∂−=
∂∂+
∂∂
2*
*2
*
**
*
**
PrRe
1
y
T
y
TV
x
TU
L ∂∂=
∂∂+
∂∂
.
Independently of the solution of these equations for a particular case, the functional
form for U* and T* can be written as,
U* = f(x*,y*,ReL, dp*/dx*),
T* = f(x*,y*,ReL, Pr, dp*/dx*).
Due to the no-slip condition at the wall surface of the boundary layer, heat transfer
occurs by conduction between the solid and the fluid molecules at the wall,
0
"
=∂∂−=
y
fs y
Tkq .
By combining Fourier’s Law evaluated at the wall with Newton’s law of cooling, we can
define the heat transfer coefficient as follows,
∞
=
−∂∂
−=TT
y
Tk
hs
y
f
0 .
In this analysis, T* is defined as s
s
TT
TTT
−−=
∞
* and as a result, h can be written in terms of
this dimensionless temperature profile T* as follows,
0
*
*
0
*
*
**)(
)(
==∞
∞
∂∂=
∂∂
−−
−=y
f
ys
sf
y
T
L
k
y
T
TTL
TTkh
This expression suggests defining a dimensionless parameter,
INME 42364
0
*
*
* =∂∂==
yf y
T
k
hLNu .
The dimensionless temperature profile implies a functional form for the Nusselt number
that depends on other parameters also,
Nu = f(x*,ReL*,Pr,dp*/dx*).
To calculate an average heat transfer coefficient, we have to integrate over x *, so the
average Nusselt number becomes independent of x*. For a prescribed geometry, *
*
dx
dp is
a result of the flow field and can be determined and specified and so the average
Nusselt number becomes,
Pr),(ReLL fNu =
This means that the Nusselt number, for a prescribed geometry is a universal function
of the Reynolds and Prandtl numbers.
Doing a similar analysis for free convection, it can be shown that, Pr),Gr(fNu = or
Pr),Ra(fNu = .
Gr is the Grashof number and Ra is the Rayleigh number. The Rayleigh number is
simply the product of Grashof and Prandtl numbers (Ra = Gr Pr). For free convection,
the Nusselt number is a universal function of the Grashof and Prandtl numbers or
Rayleigh and Prandtl numbers.
Experimental setup
Description of the Combined Convection and Radiation Heat Transfer Equipment:
The combined convection and radiation heat transfer equipment (Figure 1) allows
investigating the heat transfer of a radiant cylinder located in a crossflow of air and the
effect of increasing the surface temperature. The unit allows investigation of both
natural convection with radiation and forced convection. The experimental setup is
INME 42365
designed such that heat loss by conduction through the wall of the duct is minimized. A
thermocouple (T10) is attached to the surface of the cylinder. The surface of the cylinder
is coated with a matt black finish, which results in an emissivity close to 1.0. The
experimental setup allows the cylinder and thermocouple (T10) position to be turned
360° and locked in any position using a screw. An index mark on the end of the setup
allows the actual position of the surface to be determined. The cylinder can reach a
temperature in excess of 600°C when operated at maximum voltage and still air. The
recommended maximum for the normal operation is 500°C. Beware of hot
surfaces.
Useful Data:
Cylinder diameter D = 1.0 cm
Cylinder heated length L = 7.0 cm
Effective air velocity local to cylinder due to blockage effect: Ue = (1.22)× (Ua ),
where Ue is the effective fluid velocity and Ua is the fluid incoming velocity.
Physical properties of air at atmospheric pressure: Appendix of Heat Transfer textbook.
INME 42366
Figure 1. Combined Convection and Radiation Heat Transfer Equipment.
Procedure for convection experiments
a) Connect instruments to the heat transfer unit
b) Measure the reading for the surface temperature of the cylinder, the temperature
and velocity of the air flow and the power supplied by the heater.
c) Repeat step 2 for different velocities the air flow and various levels of power
input.
1. Free convection experiments
Observations
SetV I T9 T10
Volts Amp °C °C1 32 63 94 125 156 18
Analysis of results
SetQinput hr hC hC1th hC2th
W W/m2K W/m2K W/m2K W/m2K123456
INME 42367
The total heat input is,
Qinput = V×I
The heat transfer rate by radiation is,
Qrad = ε σ A (Ts4 – Ta4) = hr A (Ts – Ta).
So,
as
4a
4s
r TT
)T(T σ εh
−−=
The heat transfer rate by convection is then,
Qconv = Qinput - Qrad
From Newton’s law of cooling,
)TA(ThQ ascconv −=
And finally we can determine the heat transfer coefficient as follows,
)TA(T
Qh
as
convc −
= .
You must report these results for all the data points collected.
Comparison to theoretical correlations
For an isothermal long horizontal cylinder, Morgan suggests a correlation of the form,
nDD Ra C
k
D hNu ==
C and n are a coefficient and exponent respectively that depend on the Rayleigh
number as shown in the following table.
Rayleigh number C n10-10 – 10-2 0.675 0.058
10-2 – 102 1.02 0.148
102 – 104 0.850 0.188
104 – 107 0.480 0.250
107 – 1012 0.125 0.333
The Rayleigh number defined as,
Prυ
D )T(T β gRa
2
3as −= ,
INME 42368
where β is the compressibility and for an ideal gas is calculated as β = 1/T film (Tfilm in
absolute scale) and Tfilm = ½(Ts+Ta).
Churchill and Chu recommend a single correlation for a wide range of Rayleigh
numbers,
NuD={0.600.387 Ra1 /6
[10.559/Pr 9/16 ]8 /27 }
2
, Ra <1012
From both correlations, we can determine hC1th and hC2th and compare with hc obtained
from the experiment.
2. Forced convection
Observations
SetV I Ua T9 T10
Volts Amp m/s °C °C1 0.52 13 24 35 46 57 6
Analysis of results
SetQinput hr hC Re Nu1 Nu2 hC1th hC2th
W W/m2K W/m2K - - - - -1234567
Comparison with theoretical correlations
For an isothermal long horizontal cylinder, Hilper suggests the following correlation,
INME 42369
3/1PrRemDD Ck
DhNu == ,
where C and m are coefficients that depend on the Reynolds number.
ReD C m0.4-4 0.989 0.3304-40 0.911 0.385
40-4000 0.683 0.4664000-400000 0.193 0.618
40000-400000 0.027 0.805
All properties are evaluated at the film temperature,
2
TTT as
film
+= .
Churchill and Bernstein proposed the following correlation for Re·Pr>0.2
NuD=0.30.62 Re1 /2 Pr1 /3
[1 0.4Pr
2/3
]1/4 [1ReD
282000 5 /8
]4/5
,
where all properties are evaluated at the film temperature.
Using both Hilper’s and Churchill and Bernstein’s correlations we can determine the
theoretical heat transfer coefficient values hC1th and hC2th and compare with the value
obtained from the experiment hc.
3. Procedure for transient experiments
1. Start the heat transfer unit and set a voltage between 15 - 18 volts.
2. Start the heater until a steady state temperature is obtained on the heater
surface without operating the fan. Record the current, voltage, ambient
temperature (T9) , and initial surface temperature (T10).
3. Using a chronometer record the time and measure the surface temperature (T10)
to generate a time series table of at least 20 data points when the heater power
INME 423610
is turned off and the fan is operating at a predetermined speed between 2 - 6
m/s.
4. Repeat steps 2 and 3 for the same power input but without operating the fan
during the transient.
Tasks Required for Steady State Experiments
You will collect all the experimental data required during the experiments for both
natural and forced convection and will include this data in your report. In addition to the
required analysis and comparison with correlations, you will generate the following plots
for both natural and forced convection experiments:
(a) Surface temperature vs heat input to cylinder for the natural convection experiment.
(b) Surface temperature vs incoming fluid velocity for the forced convection experiment.
(c) On the same graph, plot the Nusselt numbers determined from the experimental
data and correlations vs Rayleigh or Reynolds number depending on the case.
(d) Show tables comparing the experimental values to the predicted values using the
respective correlations and calculate the percentage difference between these values.
(e) What is the contribution of radiative heat transfer to the process?
Tasks Required for Transient Experiments
(a) Generate graphs that show the surface temperature versus time in order to compare
to the expected theoretical temperature values on the same graph.
(b) Calculate the experimental and theoretical heat transfer rate from the system to the
surroundings as a function of time and present the results in graphical form.
(c) Report the experimental and theoretical thermal time constant of the system.
INME 423611
(d) What is the contribution of radiative heat transfer to the process? Discuss the
effectiveness of the lumped thermal capacitance model to describe the transient
temperature response of the cylinder.
INME 423612