National Fasteners Catalog

8/19/2019 National Fasteners Catalog

1/70

ISO 9001:2008 CERTIFIED


2/70

TABLE OF CONTENTSPRODUCT CATALOG

CARRIAGE BOLTS

GRADE 8 FULL THREAD - SHAKER SCREEN 2PLOW BOLTS

GRADE 8 #3 DOME HEAD 3

HEX FLANGE SCREWS

GRADE 5 4

GRADE 8 5

GRADE 5 SERRATED 9

GRADE 8 SERRATED 12

18-8 STAINLESS STEEL SERRATED 13

GRADE 5 LARGE FLANGE SERRATED 14

GRADE 2 FLANGE HEAD LAG SCREWS 15

HEX FLANGE NUTS

GRADE 5 16

GRADE 8 16

CASE HARDENED SERRATED 17

CASE HARDENED LARGE FLANGE SERRATED 17

GRADE 5 SERRATED 18

GRADE 8 SERRATED 18

18-8 STAINLESS STEEL SERRATED 19

GRADE G ALL METAL TOP LOCK NUTS 20

GRADE F NYLON INSERT LOCK NUTS 20METRIC HEX FLANGE SCREWS

CLASS 8.8 21

CLASS 10.9 22

CLASS 8.8 SERRATED 25

CLASS 10.9 JIS 26METRIC HEX FLANGE NUTS

CLASS 10 27

CLASS 10 LOCK NUTS 27

CLASS 8 SERRATED 28

CLASS 10 JIS 28

CLASS 10 JIS SERRATED 29

WASHERS

USS “NT” HARDENED FLAT WASHERS 30

SAE “NT” HARDENED FLAT WASHERS 30

USS “NT2” THICK HARDENED FLAT WASHERS 31

SAE “NT2” THICK HARDENED FLAT WASHERS 31

SAE “NTX” EXTRA THICK HARD FLAT WASHERS 32

1/8” EXTRA THICK FENDER WASHERS 32

TECHNICAL DRAWINGS

33

TERMS & CONDITIONS

67

NOTES

68


3/702 p 440.350.1430 / www. angescrews.com / f 440.350.1676

CARRIAGE BOLTS GRADE 8 - FULL THREAD - SHAKER SCREEN BOLTS

PLAIN FINISH - ASME B18.5, ROUND HEAD, SQUARE NECK, FULLY THREADED - SAE J429 GRADE 8

Technical Drawing on Page 34

PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY

NET WGT PER1000 PIECES

50C200BCG8PL/FT 1/2-13X2 25 300 131.00

50C250BCG8PL/FT 1/2-13X2-1/2 25 250 158.00

50C300BCG8PL/FT 1/2-13X3 25 210 186.0050C350BCG8PL/FT 1/2-13X3-1/2 15 180 214.00


50C500BCG8PL/FT 1/2-13X5 10 130 297.00

50C600BCG8PL/FT 1/2-13X6 5 125 347.00


62C300BCG8PL/FT 5/8-11X3 10 130 301.00

62C350BCG8PL/FT 5/8-11X3-1/2 10 120 343.0062C400BCG8PL/FT 5/8-11X4 10 100 385.00

62C500BCG8PL/FT 5/8-11X5 5 90 469.0062C600BCG8PL/FT 5/8-11X6 5 75 552.00

75C250BCG8PL/FT 3/4-10X2-1/2 10 100 392.00

75C300BCG8PL/FT 3/4-10X3 5 90 452.00

75C350BCG8PL/FT 3/4-10X3-1/2 5 80 522.0075C400BCG8PL/FT 3/4-10X4 5 70 574.00

75C500BCG8PL/FT 3/4-10X5 5 60 694.0075C600BCG8PL/FT 3/4-10X6 5 50 815.00


4/70

1 5 0 M P S I

p 440.350.1430 / www. angescrews.com / f 440.350.1676

PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


62C200BPL8PL 5/8-11X2 20 220 175.40

62C225BPL8PL 5/8-11X2-1/4 20 200 196.90

62C250BPL8PL 5/8-11X2-1/2 15 180 218.5062C300BPL8PL 5/8-11X3 10 150 261.60

62C350BPL8PL 5/8-11X3-1/2 10 130 304.7062C400BPL8PL 5/8-11X4 10 110 347.60

62C450BPL8PL 5/8-11X4-1/2 5 100 395.60

62C500BPL8PL 5/8-11X5 5 90 439.30

75C200BPL8PL 3/4-10X2 10 150 255.5075C225BPL8PL 3/4-10X2-1/4 10 140 281.00

75C250BPL8PL 3/4-10X2-1/2 10 120 312.1075C275BPL8PL 3/4-10X2-3/4 10 110 343.20

75C300BPL8PL 3/4-10X3 5 100 374.3075C350BPL8PL 3/4-10X3-1/2 5 90 436.50

75C400BPL8PL 3/4-10X4 5 80 498.70

PLOW BOLTS GRADE 8 - #3 DOME HEAD

PLAIN FINISH - ASME B18.9 - SAE J429 GRADE 8 - 150,000 PSI




PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25C50BFL5Z 1/4-20X1/2 100 2700 14.76

25C62BFL5Z 1/4-20X5/8 100 2500 16.08 25C75BFL5Z* 1/4-20X3/4 100 2200 17.85

25C100BFL5Z* 1/4-20X1 100 2000 20.26 25C125BFL5Z* 1/4-20X1-1/4 100 1700 23.57

25C150BFL5Z* 1/4-20X1-1/2 100 1300 30.18 25C175BFL5Z 1/4-20X1-3/4 100 1200 33.48

25C200BFL5Z 1/4-20X2 100 1100 37.00

31C50BFL5Z 5/16-18X1/2 100 1400 27.31

31C62BFL5Z* 5/16-18X5/8 100 1400 28.31 31C75BFL5Z* 5/16-18X3/4 100 1200 32.00

31C100BFL5Z* 5/16-18X1 100 1100 36.30 31C125BFL5Z* 5/16-18X1-1/4 100 1000 39.87

31C150BFL5Z* 5/16-18X1-1/2 100 800 46.70 31C175BFL5Z 5/16-18X1-3/4 100 700 51.98

31C200BFL5Z 5/16-18X2 50 700 57.27

37C50BFL5Z 3/8-16X1/2 100 900 43.77

37C62BFL5Z* 3/8-16X5/8 100 900 44.90 37C75BFL5Z* 3/8-16X3/4 100 800 48.00

37C100BFL5Z* 3/8-16X1 100 700 54.70

37C125BFL5Z* 3/8-16X1-1/4 100 600 60.85 37C150BFL5Z* 3/8-16X1-1/2 50 600 66.00

37C175BFL5Z 3/8-16X1-3/4 50 500 77.60 37C200BFL5Z 3/8-16X2 50 450 85.00

50C100BFL5Z* 1/2-13X1 25 300 127.02

50C125BFL5Z* 1/2-13X1-1/4 25 275 138.06

50C150BFL5Z* 1/2-13X1-1/2 25 275 143.61 50C175BFL5Z 1/2-13X1-3/4 25 250 160.50

50C200BFL5Z 1/2-13X2 25 225 179.07 50C225BFL5Z 1/2-13X2-1/4 25 200 192.73

50C250BFL5Z 1/2-13X2-1/2 25 175 206.60

FLANGE SCREWS GRADE 5 - HEX HEAD FLANGE

ZINC CLEAR FINISH - IFI-111 - SAE J429 GRADE 5

Technical Drawing on Page 36*ALSO STOCKED IN ZINC YELLOW


6/70p 440.350.1430 / www. angescrews.com / f 440.350.1676

PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25C50BFL8P* 1/4-20X1/2 100 2700 14.76

25C62BFL8P 1/4-20X5/8 100 2500 16.08

25C75BFL8P* 1/4-20X3/4 100 2200 17.85 25C100BFL8P* 1/4-20X1 100 2000 20.26

25C125BFL8P* 1/4-20X1-1/4 100 1700 23.37 25C150BFL8P* 1/4-20X1-1/2 100 1300 30.18

25C175BFL8P* 1/4-20X1-3/4 100 1200 33.48

25C200BFL8P* 1/4-20X2 100 1100 37.00 25C225BFL8P* 1/4-20X2-1/4 100 1000 40.31 25C250BFL8P* 1/4-20X2-1/2 50 900 41.41

25C300BFL8P* 1/4-20X3 50 750 50.44

31C50BFL8P 5/16-18X1/2 100 1400 27.31

31C75BFL8P* 5/16-18X3/4 100 1200 32.00 31C100BFL8P* 5/16-18X1 100 1100 36.30

31C125BFL8P* 5/16-18X1-1/4 100 1000 39.87 31C150BFL8P* 5/16-18X1-1/2 100 800 46.70

31C175BFL8P* 5/16-18X1-3/4 100 700 51.98 31C200BFL8P* 5/16-18X2 50 700 57.27

31C225BFL8P* 5/16-18X2-1/4 50 650 62.33

31C250BFL8P* 5/16-18X2-1/2 50 600 67.84 31C300BFL8P* 5/16-18X3 50 500 78.41

37C62BFL8P 3/8-16X5/8 100 900 44.90

37C75BFL8P* 3/8-16X3/4 100 800 48.00

37C100BFL8P* 3/8-16X1 100 700 54.70 37C125BFL8P* 3/8-16X1-1/4 100 600 60.85

37C150BFL8P* 3/8-16X1-1/2 50 600 66.00 37C175BFL8P* 3/8-16X1-3/4 50 500 77.50

37C200BFL8P* 3/8-16X2 50 450 85.00 37C225BFL8P* 3/8-16X2-1/4 50 400 96.00

37C250BFL8P* 3/8-16X2-1/2 25 375 105.00 37C275BFL8P* 3/8-16X2-3/4 25 350 108.80

37C300BFL8P* 3/8-16X3 25 300 115.42

GRADE 8 - HEX HEAD FLANGE

PHOSPHATE & OIL FINISH - IFI-111 - SAE J429 GRADE 8


FLANGE SCREWS

*ALSO STOCKED IN ZINC YELLOW



PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


37C400BFL8P 3/8-16X4 25 250 146.50

43C100BFL8P 7/16-14X1 50 500 76.00 43C125BFL8P 7/16-14X1-1/4 50 450 90.50

43C150BFL8P 7/16-14X1-1/2 50 400 97.30

43C175BFL8P 7/16-14X1-3/4 50 350 103.00 43C200BFL8P 7/16-14X2 25 325 118.00

43C225BFL8P 7/16-14X2-1/4 25 300 122.50 43C250BFL8P 7/16-14X2-1/2 25 275 140.00

43C275BFL8P 7/16-14X2-3/4 25 250 146.00 43C300BFL8P 7/16-14X3 25 250 155.00

50C75BFL8P 1/2-13X3/4 25 375 104.00 50C100BFL8P* 1/2-13X1 25 300 127.02

50C125BFL8P* 1/2-13X1-1/4 25 275 138.06 50C150BFL8P* 1/2-13X1-1/2 25 275 143.61

50C175BFL8P* 1/2-13X1-3/4 25 250 160.50 50C200BFL8P* 1/2-13X2 25 225 179.07

50C225BFL8P 1/2-13X2-1/4 25 200 192.73 50C250BFL8P* 1/2-13X2-1/2 25 175 206.60

50C275BFL8P* 1/2-13X2-3/4 25 175 220.26 50C300BFL8P* 1/2-13X3 25 175 233.92

50C325BFL8P 1/2-13X3-1/4 15 150 241.00

50C350BFL8P 1/2-13X3-1/2 15 150 248.00 50C375BFL8P 1/2-13X3-3/4 15 150 260.00

50C400BFL8P 1/2-13X4 15 135 282.00 50C450BFL8P 1/2-13X4-1/2 15 120 310.00

50C500BFL8P 1/2-13X5 15 120 337.00

62C125BFL8P 5/8-11X1-1/4 20 160 243.61

62C150BFL8P* 5/8-11X1-1/2 20 140 261.00 62C175BFL8P* 5/8-11X1-3/4 20 140 278.63

62C200BFL8P* 5/8-11X2 20 120 296.25 62C225BFL8P* 5/8-11X2-1/4 15 120 313.65

62C250BFL8P* 5/8-11X2-1/2 15 120 331.27




FLANGE SCREWS




PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


62C275BFL8P 5/8-11X2-3/4 15 105 368.27

62C300BFL8P 5/8-11X3 10 90 389.64

62C325BFL8P 5/8-11X3-1/4 10 90 411.23 62C350BFL8P 5/8-11X3-1/2 10 90 432.59

62C375BFL8P 5/8-11X3-3/4 10 80 475.43 62C400BFL8P 5/8-11X4 10 70 518.27

62C450BFL8P 5/8-11X4-1/2 5 70 554.61

62C500BFL8P 5/8-11X5 5 70 561.00 62C550BFL8P 5/8-11X5-1/2 5 60 603.95 62C600BFL8P 5/8-11X6 5 60 646.68

75C150BFL8P 3/4-10X1-1/2 10 100 380.50 75C175BFL8P* 3/4-10X1-3/4 10 90 416.50

75C200BFL8P* 3/4-10X2 10 80 448.00 75C225BFL8P* 3/4-10X2-1/4 10 80 475.50

75C250BFL8P* 3/4-10X2-1/2 10 80 500.00 75C275BFL8P 3/4-10X2-3/4 10 70 529.00

75C300BFL8P* 3/4-10X3 5 70 572.00 75C325BFL8P 3/4-10X3-1/4 5 60 589.60

75C350BFL8P 3/4-10X3-1/2 5 60 605.00

75C400BFL8P 3/4-10X4 5 50 670.00 75C450BFL8P 3/4-10X4-1/2 5 50 737.50

75C500BFL8P 3/4-10X5 5 40 816.00 75C600BFL8P 3/4-10X6 5 40 936.67

50F100BFL8P 1/2-20X1 25 300 127.02 50F125BFL8P 1/2-20X1-1/4 25 275 138.06

50F150BFL8P 1/2-20X1-1/2 25 275 143.61 50F175BFL8P 1/2-20X1-3/4 25 250 160.50

50F200BFL8P 1/2-20X2 25 225 179.07 50F225BFL8P 1/2-20X2-1/4 25 200 192.73

50F250BFL8P 1/2-20X2-1/2 25 175 206.60 50F275BFL8P 1/2-20X2-3/4 25 175 220.26

50F300BFL8P 1/2-20X3 25 175 233.92




FLANGE SCREWS




PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


50F400BFL8P 1/2-20X4 15 135 282.00

50F500BFL8P 1/2-20X5 15 120 337.00

62F150BFL8P 5/8-18X1-1/2 20 140 261.00

62F175BFL8P 5/8-18X1-3/4 20 140 278.63 62F200BFL8P 5/8-18X2 20 120 296.25

62F225BFL8P 5/8-18X2-1/4 15 120 313.65

62F250BFL8P 5/8-18X2-1/2 15 120 331.27 62F275BFL8P 5/8-18X2-3/4 15 105 368.27

62F300BFL8P 5/8-18X3 10 90 389.64 62F350BFL8P 5/8-18X3-1/2 10 90 432.59

62F400BFL8P 5/8-18X4 10 70 518.27

75F175BFL8P 3/4-16X1-3/4 10 90 416.50

75F200BFL8P 3/4-16X2 10 80 448.00 75F225BFL8P 3/4-16X2-1/4 10 80 475.50

75F250BFL8P 3/4-16X2-1/2 10 80 500.00 75F275BFL8P 3/4-16X2-3/4 10 70 529.00

75F300BFL8P 3/4-16X3 5 70 572.00 75F350BFL8P 3/4-16X3-1/2 5 60 636.40




FLANGE SCREWS




PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


6C25SFS5Z 6-32X1/4 100 10000 2.68

6C37SFS5Z 6-32X3/8 100 10000 2.72

6C50SFS5Z 6-32X1/2 100 8000 3.31 6C62SFS5Z 6-32X5/8 100 8000 3.51

6C75SFS5Z 6-32X3/4 100 8000 4.41 6C87SFS5Z 6-32X7/8 100 6000 4.58

6C100SFS5Z 6-32X1 100 5000 4.76

8C25SFS5Z 8-32X1/4 100 8000 3.57

8C37SFS5Z 8-32X3/8 100 7000 4.07 8C50SFS5Z 8-32X1/2 100 6000 4.56

8C75SFS5Z 8-32X3/4 100 5000 5.96 8C87SFS5Z 8-32X7/8 100 5000 6.40

8C100SFS5Z 8-32X1 100 5000 6.69

10C37SFS5Z 10-24X3/8 100 5000 6.75

10C50SFS5Z 10-24X1/2 100 5000 7.60 10C62SFS5Z 10-24X5/8 100 4000 8.62

10C75SFS5Z 10-24X3/4 100 4000 9.00 10C100SFS5Z 10-24X1 100 3000 10.50

10F37SFS5Z 10-32X3/8 100 5000 7.10 10F50SFS5Z 10-32X1/2 100 5000 7.95

10F62SFS5Z 10-32X5/8 100 4000 8.62 10F75SFS5Z 10-32X3/4 100 4000 9.25

10F100SFS5Z 10-32X1 100 3000 10.70

25C37SFS5Z 1/4-20X3/8 100 2900 13.40

25C50SFS5Z* 1/4-20X1/2 100 2700 14.76 25C62SFS5Z* 1/4-20X5/8 100 2500 15.90

25C75SFS5Z* 1/4-20X3/4 100 2300 17.05 25C87SFS5Z 1/4-20X7/8 100 2200 18.15

25C100SFS5Z* 1/4-20X1 100 2000 20.20 25C125SFS5Z* 1/4-20X1-1/4 100 1700 22.50

25C150SFS5Z* 1/4-20X1-1/2 100 1500 25.45 25C175SFS5Z 1/4-20X1-3/4 100 1400 27.50

FLANGE SCREWS GRADE 5 - HEX FLANGE HEAD SERRATED

ZINC CLEAR FINISH - IFI-111, FULLY THREADED - SAE J429 GRADE 5





PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25C200SFS5Z 1/4-20X2 100 1300 29.80

25C225SFS5Z 1/4-20X2-1/4 100 1200 31.60

25C250SFS5Z 1/4-20X2-1/2 50 1100 35.50

25C275SFS5Z 1/4-20X2-3/4 50 1000 39.60 25C300SFS5Z 1/4-20X3 50 950 40.97

31C50SFS5Z* 5/16-18X1/2 100 1400 27.35

31C62SFS5Z* 5/16-18X5/8 100 1300 30.45

31C75SFS5Z* 5/16-18X3/4 100 1200 31.00 31C87SFS5Z* 5/16-18X7/8 100 1200 33.05

31C100SFS5Z* 5/16-18X1 100 1100 35.40 31C125SFS5Z* 5/16-18X1-1/4 100 1000 38.00

31C150SFS5Z* 5/16-18X1-1/2 100 900 44.00 31C175SFS5Z 5/16-18X1-3/4 100 800 47.00

31C200SFS5Z* 5/16-18X2 50 750 52.42 31C225SFS5Z 5/16-18X2-1/4 50 700 54.50

31C250SFS5Z 5/16-18X2-1/2 50 650 59.50

31C275SFS5Z 5/16-18X2-3/4 50 600 62.80 31C300SFS5Z 5/16-18X3 50 550 67.50

37C50SFS5Z* 3/8-16X1/2 100 900 42.60

37C62SFS5Z* 3/8-16X5/8 100 900 43.00 37C75SFS5Z* 3/8-16X3/4 100 800 47.50

37C87SFS5Z 3/8-16X7/8 100 700 51.76 37C100SFS5Z* 3/8-16X1 100 700 55.10

37C125SFS5Z* 3/8-16X1-1/4 100 600 60.50

37C150SFS5Z* 3/8-16X1-1/2 50 600 65.00 37C175SFS5Z 3/8-16X1-3/4 50 550 71.50

37C200SFS5Z 3/8-16X2 50 500 77.00 37C225SFS5Z 3/8-16X2-1/4 50 450 84.50

37C250SFS5Z 3/8-16X2-1/2 25 450 88.00 37C275SFS5Z 3/8-16X2-3/4 25 400 97.50

37C300SFS5Z 3/8-16X3 25 375 105.00







PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


43C100SFS5Z 7/16-14X1 50 500 79.50 43C125SFS5Z 7/16-14X1-1/4 50 450 85.50

43C150SFS5Z 7/16-14X1-1/2 50 400 89.50 43C200SFS5Z 7/16-14X2 25 350 111.00

50C75SFS5Z 1/2-13X3/4 25 400 98.50 50C87SFS5Z 1/2-13X7/8 25 350 108.44

50C100SFS5Z* 1/2-13X1 25 300 116.10 50C125SFS5Z* 1/2-13X1-1/4 25 300 129.50

50C150SFS5Z* 1/2-13X1-1/2 25 275 140.00 50C175SFS5Z 1/2-13X1-3/4 25 250 149.60

50C200SFS5Z* 1/2-13X2 25 250 157.00 50C225SFS5Z 1/2-13X2-1/4 25 225 165.00

50C250SFS5Z 1/2-13X2-1/2 25 200 178.00 50C300SFS5Z 1/2-13X3 25 175 216.30

62C150SFS5Z 5/8-11X1-1/2 20 160 240.00 62C175SFS5Z 5/8-11X1-3/4 20 160 253.00

62C200SFS5Z 5/8-11X2 20 140 280.00







PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25C50SFS8Z 1/4-20X1/2 100 2700 14.76

25C75SFS8Z 1/4-20X3/4 100 2300 17.05

25C100SFS8Z 1/4-20X1 100 2000 20.20 25C125SFS8Z 1/4-20X1-1/4 100 1700 22.50

25C150SFS8Z 1/4-20X1-1/2 100 1500 25.45

31C50SFS8Z 5/16-18X1/2 100 1400 27.35

31C75SFS8Z 5/16-18X3/4 100 1200 31.00 31C100SFS8Z 5/16-18X1 100 1100 35.40

31C125SFS8Z 5/16-18X1-1/4 100 1000 38.00 31C150SFS8Z 5/16-18X1-1/2 100 900 44.00

31C175SFS8Z 5/16-18X1-3/4 100 800 47.00 31C200SFS8Z 5/16-18X2 50 750 52.42

37C75SFS8Z 3/8-16X3/4 100 800 47.50 37C87SFS8Z 3/8-16X7/8 100 700 51.76

37C100SFS8Z 3/8-16X1 100 700 55.10 37C125SFS8Z 3/8-16X1-1/4 100 600 60.50

37C150SFS8Z 3/8-16X1-1/2 50 600 65.00 37C175SFS8Z 3/8-16X1-3/4 50 550 71.50

37C200SFS8Z 3/8-16X2 50 500 77.00





F593C


PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25C50SFSSS 1/4-20X1/2 100 2700 14.77

25C75SFSSS 1/4-20X3/4 100 2300 17.20

25C100SFSSS 1/4-20X1 100 2000 20.28 25C125SFSSS 1/4-20X1-1/4 100 1700 23.59

25C150SFSSS 1/4-20X1-1/2 100 1500 27.12

31C50SFSSS 5/16-18X1/2 100 1400 27.34

31C75SFSSS 5/16-18X3/4 100 1200 31.53 31C100SFSSS 5/16-18X1 100 1100 35.71

31C125SFSSS 5/16-18X1-1/4 100 1000 39.90 31C150SFSSS 5/16-18X1-1/2 100 900 44.09

37C50SFSSS 3/8-16X1/2 100 900 43.87 37C75SFSSS 3/8-16X3/4 100 800 50.27

37C100SFSSS 3/8-16X1 100 700 56.44 37C125SFSSS 3/8-16X1-1/4 100 600 62.61

37C150SFSSS 3/8-16X1-1/2 50 600 68.56

FLANGE SCREWS 18-8 STAINLESS STEEL - HEX FLANGE HEAD SERRATED

PASSIVATED - IFI-111, FULLY THREADED - ASTM 593C 18-8 (304)




PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25C75SLFS5Z 1/4-20X3/4 100 2300 16.80

25C100SLFS5Z 1/4-20X1 100 2000 19.00

31C75SLFS5Z 5/16-18X3/4 100 1200 31.00

31C100SLFS5Z 5/16-18X1 100 1100 35.00

37C75SLFS5Z 3/8-16X3/4 100 800 47.50

37C100SLFS5Z 3/8-16X1 100 700 53.50

FLANGE SCREWS GRADE 5 - HEX LARGE FLANGE HEAD SERRATED





PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25D100FLS2G 1/4-10X1 100 2100 18.72

25D150FLS2G 1/4-10X1-1/2 100 1600 24.05

25D200FLS2G 1/4-10X2 50 1350 29.50 25D250FLS2G 1/4-10X2-1/2 50 1100 35.24

25D300FLS2G 1/4-10X3 50 950 41.85

31D100FLS2G 5/16-9X1 100 1200 30.84

31D150FLS2G 5/16-9X1-1/2 50 1050 37.65 31D200FLS2G 5/16-9X2 50 800 48.00

31D250FLS2G 5/16-9X2-1/2 50 700 54.00

37D150FLS2G 3/8-7X1-1/2 50 650 58.50

37D200FLS2G 3/8-7X2 50 600 63.88 37D250FLS2G 3/8-7X2-1/2 25 475 80.90

37D300FLS2G 3/8-7X3 25 400 95.50 37D400FLS2G 3/8-7X4 25 325 117.50

FLANGE LAG SCREWS GRADE 2 - HEX HEAD FLANGE

HOT DIP GALVANIZED - HEAD DIMENSIONS IFI-111 - LAG THREAD ASME B18.2.1



PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25CNHF5Z/FS 1/4-20 100 4200 9.50

31CNHF5Z/FS 5/16-18 100 2800 14.00

37CNHF5Z/FS 3/8-16 100 2100 18.75 50CNHF5Z/FS 1/2-13 25 850 46.00

62CNHF5Z/FS 5/8-11 25 425 89.00

FLANGE NUTS GRADE 5 - HEX FLANGE

ZINC CLEAR FINISH - ASME B18.2.2 (IFI-145) - SAE J995 GRADE 5


PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25CNHF8P/FS 1/4-20 100 4200 9.50

31CNHF8P/FS 5/16-18 100 2800 14.00

37CNHF8P/FS 3/8-16 100 2100 18.75 50CNHF8P/FS 1/2-13 25 850 46.00

62CNHF8P/FS 5/8-11 25 425 89.00 75CNHF8P/FS 3/4-10 20 280 138.50

50FNHF8P/FS 1/2-20 25 850 46.00 62FNHF8P/FS 5/8-18 25 425 89.00

75FNHF8P/FS 3/4-16 20 280 138.50

FLANGE NUTS GRADE 8 - HEX FLANGE

PHOSPHATE & OIL FINISH - ASME B18.2.2 (IFI-145) - SAE J995 GRADE 8




PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


6CSLN2Z #6-32 100 11000 3.50

8CSLN2Z #8-32 100 7600 5.25

10CSLN2Z #10-24 100 6000 6.50 25CSLN2Z 1/4-20 100 4400 9.00

31CSLN2Z 5/16-18 100 3200 12.30 37CSLN2Z 3/8-16 100 2100 19.00

43CSLN2Z 7/16-14 100 1200 33.00

50CSLN2Z 1/2-13 50 900 44.00 62CSLN2Z 5/8-11 25 450 86.00 75CSLN2Z 3/4-10 25 275 138.00

10FSLN2Z #10-32 100 6000 6.50 25FSLN2Z 1/4-28 100 4400 9.00

31FSLN2Z 5/16-24 100 3200 12.30 37FSLN2Z 3/8-24 100 2100 19.00

43FSLN2Z 7/16-20 100 1200 33.00 50FSLN2Z 1/2-20 50 900 44.00


CASE HARDENED - HEX FLANGE SERRATED

ZINC CLEAR FINISH - ASME B18.2.2 (IFI-145) - SURFACE HARDNESS R15N 79/86

CASE HARDENED - HEX LARGE FLANGE SERRATED

ZINC CLEAR FINISH - ASME B18.2.2 (IFI-145) - SURFACE HARDNESS R15N 79/86

PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25CLSLN2Z 1/4-20 100 2800 14.00

31CLSLN2Z 5/16-18 100 1700 22.50

37CLSLN2Z 3/8-16 100 1300 29.00 50CLSLN2Z 1/2-13 50 850 46.00


FLANGE NUTS

FLANGE NUTS


19/70

PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25CSLN5Z 1/4-20 100 4400 9.00

31CSLN5Z 5/16-18 100 3200 12.30

37CSLN5Z 3/8-16 100 2100 19.00 50CSLN5Z 1/2-13 50 900 44.00


18 p 440.350.1430 / www. angescrews.com / f 440.350.1676

GRADE 5- HEX FLANGE SERRATED

ZINC CLEAR FINISH - ASME B18.2.2 (IFI-145) - SAE J995 GRADE 5

PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25CSLN8PL* 1/4-20 100 4400 9.00

31CSLN8PL* 5/16-18 100 3200 12.30

37CSLN8PL* 3/8-16 100 2100 19.00 50CSLN8PL* 1/2-13 50 900 44.00

62CSLN8PL* 5/8-11 25 450 86.00

75CSLN8PL* 3/4-10 25 275 138.00

GRADE 8 - HEX FLANGE SERRATED

PLAIN & OIL - ASME B18.2.2 (IFI-145) - SAE J995 GRADE 8



FLANGE NUTS

FLANGE NUTS



PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25CSLNSS 1/4-20 100 4400 9.00

31CSLNSS 5/16-18 100 3200 12.90

37CSLNSS 3/8-16 100 2100 18.30


FLANGE NUTS 18-8 STAINLESS STEEL - HEX FLANGE SERRATED

PASSIVATED - ASME B18.2.2 (IFI-145) - ASTM 594C 18-8 (304)



PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25CNHFGP* 1/4-20 100 3900 10.10

31CNHFGP* 5/16-18 100 2400 16.30

37CNHFGP* 3/8-16 100 1500 25.50 43CNHFGP* 7/16-14 50 950 41.80

50CNHFGP* 1/2-13 25 725 56.15 62CNHFGP* 5/8-11 25 350 109.60

75CNHFGP* 3/4-10 20 240 156.70

87CNHFGP 7/8-9 15 165 230.80 50FNHFGP* 1/2-20 25 725 56.15

62FNHFGP* 5/8-18 25 350 109.60 75FNHFGP 3/4-16 20 240 156.70


FLANGE LOCK NUTS GRADE G - HEX FLANGE

PHOSPHATE & OIL FINISH - IFI-100/107 CONE STYLE - ALL METAL, TOP LOCK

PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


25CNFNFZ 1/4-20 100 4000 10.14

31CNFNFZ 5/16-18 100 2700 14.55 37CNFNFZ 3/8-16 100 1900 21.16 50CNFNFZ 1/2-13 50 700 51.07

62CNFNFZ 5/8-11 25 400 96.56

FLANGE LOCK NUTS GRADE F - HEX FLANGE NYLON INSERT

ZINC CLEAR FINISH - IFI-100/107 - NYLON INSERT, TOP LOCK

Technical Drawing on Page 50*ALSO STOCKED IN ZINC YELLOW WAX



8.8


PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


M6C12BF88Y/D M6-1.0X12 100 2600 15.42

M6C16BF88Y/D M6-1.0X16 100 2400 16.96

M6C20BF88Y/D M6-1.0X20 100 2200 18.28 M6C25BF88Y/D M6-1.0X25 100 2000 19.60

M6C30BF88Y/D M6-1.0X30 100 1800 22.50

M8C16BF88Y/D M8-1.25X16 100 1300 30.50



M8C40BF88Y/D M8-1.25X40 100 800 48.50

M10C20BF88Y/D M10-1.5X20 100 700 55.07







M12C60BF88Y/D M12-1.75X60 25 250 155.60

METRIC FLANGE SCREWS CLASS 8.8 - HEX HEAD FLANGE

ZINC YELLOW FINISH - DIN 6921 - ISO 898-1 CLASS 8.8



10.9


PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


M5C10BF10P/D M5-.8X10 100 5000 7.90

M5C12BF10P/D M5-.8X12 100 5000 8.00 M5C16BF10P/D M5-.8X16 100 4200 9.40

M5C20BF10P/D M5-.8X20 100 4200 9.50

M6C10BF10P/D M6-1.0X10 100 2800 14.00

M6C12BF10P/D M6-1.0X12 100 2600 15.42 M6C16BF10P/D M6-1.0X16 100 2400 16.96



M6C40BF10P/D M6-1.0X40 100 1500 26.87


M6C60BF10P/D M6-1.0X60 50 1100 36.56


M8C20BF10P/D M8-1.25X20 100 1200 33.48




M8C60BF10P/D M8-1.25X60 50 600 66.08


M10C16BF10P/D M10-1.5X16 100 800 49.00




PHOSPHATE & OIL FINISH - DIN 6921 - ISO 898-1 CLASS 10.9



10.9


PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


M10C40BF10P/D M10-1.5X40 50 500 78.41

M10C45BF10P/D M10-1.5X45 50 450 85.24











M14C60BF10P/D M14-2.0X60 25 175 230.00



M16C35BF10P/D M16-2.0X35 20 200 203.18

M16C40BF10P/D M16-2.0X40 20 160 231.71


M16C60BF10P/D M16-2.0X60 15 135 299.55





10.9


PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


M16C70BF10P/D M16-2.0X70 15 120 334.80

M16C80BF10P/D M16-2.0X80 10 110 365.63







PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


M6C12SFS88Z M6-1.0X12 100 3200 12.50

M6C16SFS88Z M6-1.0X16 100 2400 16.96

M6C20SFS88Z M6-1.0X20 100 2200 18.28 M6C25SFS88Z M6-1.0X25 100 2000 19.60


M6C40SFS88Z M6-1.0X40 100 1500 26.87

M8C16SFS88Z M8-1.25X16 100 1300 30.84



M8C40SFS88Z M8-1.25X40 100 800 48.46

M10C20SFS88Z M10-1.5X20 100 700 55.07




M12C40SFS88Z M12-1.75X40 25 350 114.54

8.8


METRIC FLANGE SCREWS CLASS 8.8 - HEX HEAD FLANGE SERRATED

ZINC CLEAR FINISH - DIN 6921, FULL THREAD - ISO 898-1 CLASS 8.8



PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


M6C12BF10Z/J M6-1.0X12 100 2800 14.30

M6C16BF10Z/J M6-1.0X16 100 2700 14.70

M6C20BF10Z/J M6-1.0X20 100 2500 16.10 M6C25BF10Z/J M6-1.0X25 100 2300 17.50


M6C40BF10Z/J M6-1.0X40 100 1500 26.87

M8C12BF10Z/J M8-1.25X12 100 1600 24.80





M8C60BF10Z/J M8-1.25X60 50 600 63.50

M10F16BF10Z/J M10-1.25X16 100 800 47.50

M10F20BF10Z/J M10-1.25X20 100 700 52.00 M10F25BF10Z/J M10-1.25X25 100 700 57.00


M10F40BF10Z/J M10-1.25X40 50 500 76.50



10.9


METRIC FLANGE SCREWS CLASS 10.9 - JIS HEX HEAD FLANGE

PHOSPHATE & OIL FINISH - JIS B1189 TYPE 2 - JIS B1051 CLASS 10.9



PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


M6CNHF10Z* M6-1.0 100 5700 7.00

M8CNHF10Z* M8-1.25 100 2500 14.50

M10CNHF10Z* M10-1.5 100 1600 24.00 M12CNHF10Z* M12-1.75 25 950 42.00

M16CNHF10Z* M16-2.0 25 375 105.50

METRIC FLANGE NUTS CLASS 10 - HEX FLANGE

ZINC CLEAR FINISH - DIN 6923 - ISO 898-2 CLASS 10

1 0


PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


M6CFLN10P M6-1.0 100 4700 8.50

M8CFLN10P M8-1.25 100 2500 16.00 M10CFLN10P M10-1.5 100 1400 28.00

M12CFLN10P M12-1.75 25 825 48.00 M14CFLN10P M14-2.0 25 500 79.00

M16CFLN10P M16-2.0 25 375 100.50

METRIC FLANGE NUTS CLASS 10 - HEX FLANGE LOCK NUTS

PHOSPHATE & OIL FINISH - DIN 6927 - ALL METAL, TOP LOCK - ISO 898-2 CLASS 10

1 0


*ALSO STOCKED IN PHOSPHATE & OIL



PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


M6CSLN8Z M6-1.0 100 5700 7.00

M8CSLN8Z M8-1.25 100 2500 14.50

M10CSLN8Z M10-1.5 100 1600 24.00 M12CSLN8Z M12-1.75 25 950 41.00

8


METRIC FLANGE NUTS CLASS 8 - HEX FLANGE SERRATED

ZINC CLEAR FINISH - DIN 6923 - ISO 898-2 CLASS 8

PARTNUMBER SIZE

PACKAGEQUANTITY

1/4 KEGQUANTITY


M6CNHF10Z/J M6-1.0 100 5700 7.00

M8CNHF10Z/J M8-1.25 100 2500 14.50 M10FNHF10Z/J M10-1.25 100 1600 24.00

1 0


METRIC FLANGE NUTS CLASS 10 - JIS HEX FLANGE

ZINC CLEAR FINISH - JIS B1190 - CLASS 10


30/70



PARTNUMBER SIZE ID OD

MAXTHICK

MINTHICK

PACKAGEQUANTITY

1/4 KEGQUANTITY


25UNT8Y 1/4" 0.312 0.734 0.065 0.055 100 7000 5.50

31UNT8Y 5/16" 0.375 0.875 0.080 0.064 100 3900 10.35

37UNT8Y 3/8" 0.438 1.000 0.080 0.064 100 3000 13.50 43UNT8Y 7/16" 0.500 1.250 0.080 0.064 100 1800 22.10

50UNT8Y 1/2" 0.562 1.375 0.116 0.100 100 1200 32.50 56UNT8Y 9/16" 0.625 1.469 0.116 0.100 100 1100 37.00

62UNT8Y 5/8" 0.688 1.750 0.138 0.122 50 600 63.50

75UNT8Y 3/4" 0.812 2.000 0.138 0.122 25 400 93.80 87UNT8Y 7/8" 0.938 2.250 0.160 0.136 25 300 131.40 100UNT8Y 1" 1.062 2.500 0.160 0.136 25 250 162.00

WASHERS HARDENED FLAT - USS “NT” PATTERN

ZINC YELLOW FINISH - ASTM F436 THROUGH HARDENED - GRADE 8

1/4 U

NT


WASHERS HARDENED FLAT - SAE “NT” PATTERNZINC YELLOW FINISH - ASTM F436 THROUGH HARDENED - GRADE 8

1/4 S

NT



MAXTHICK

MINTHICK

PACKAGEQUANTITY

1/4 KEGQUANTITY


25SNT8Y 1/4" 0.281 0.625 0.065 0.055 100 9700 4.15

31SNT8Y 5/16" 0.344 0.688 0.065 0.055 100 9700 4.15 37SNT8Y 3/8" 0.406 0.812 0.065 0.055 100 7000 5.80

43SNT8Y 7/16" 0.469 0.921 0.065 0.055 100 5000 7.45 50SNT8Y 1/2" 0.531 1.062 0.116 0.100 100 2300 17.50 56SNT8Y 9/16" 0.594 1.156 0.116 0.100 100 1900 20.75

62SNT8Y 5/8" 0.656 1.312 0.138 0.122 50 1150 35.00 75SNT8Y 3/4" 0.812 1.469 0.138 0.122 50 1100 36.70

87SNT8Y 7/8" 0.938 1.750 0.152 0.136 50 600 65.80 100SNT8Y 1" 1.062 2.000 0.160 0.136 50 450 85.00




MAXTHICK

MINTHICK

PACKAGEQUANTITY

1/4 KEGQUANTITY


25UNT28Y 1/4" 0.312 0.734 0.080 0.064 100 5400 7.50

31UNT28Y 5/16" 0.375 0.875 0.093 0.079 100 3700 11.05

37UNT28Y 3/8" 0.438 1.000 0.093 0.079 100 2500 15.90

43UNT28Y 7/16" 0.500 1.250 0.106 0.090 100 1500 26.35 50UNT28Y 1/2" 0.562 1.375 0.146 0.122 100 900 41.50

56UNT28Y 9/16" 0.625 1.469 0.146 0.122 100 800 48.50 62UNT28Y 5/8" 0.688 1.750 0.160 0.136 50 500 78.00

75UNT28Y 3/4" 0.812 2.000 0.160 0.136 25 400 99.50 87UNT28Y 7/8" 0.938 2.250 0.160 0.136 25 300 132.50 100UNT28Y 1" 1.062 2.500 0.160 0.136 25 275 148.00

WASHERS HARDENED FLAT - USS “NT2” THICK PATTERN


1/4 U

NT2


WASHERS HARDENED FLAT - SAE “NT2” THICK PATTERNZINC YELLOW FINISH - ASTM F436 THROUGH HARDENED - GRADE 8

1/4 S

NT2



MAXTHICK

MINTHICK

PACKAGEQUANTITY

1/4 KEGQUANTITY


25SNT28Y 1/4" 0.281 0.625 0.080 0.064 100 8000 5.00

31SNT28Y 5/16" 0.344 0.688 0.093 0.079 100 6100 6.50 37SNT28Y 3/8" 0.406 0.812 0.093 0.079 100 4800 8.50

43SNT28Y 7/16" 0.469 0.921 0.106 0.090 100 3200 12.60 50SNT28Y 1/2" 0.531 1.062 0.146 0.122 100 1800 22.00 56SNT28Y 9/16" 0.594 1.156 0.146 0.122 100 1400 28.00

62SNT28Y 5/8" 0.656 1.312 0.160 0.136 50 1050 39.00 75SNT28Y 3/4" 0.812 1.469 0.160 0.136 50 900 44.50

87SNT28Y 7/8" 0.938 1.750 0.160 0.136 50 600 68.00 100SNT28Y 1" 1.062 2.000 0.160 0.136 50 450 86.20




MAXTHICK

MINTHICK

PACKAGEQUANTITY

1/4 KEGQUANTITY


25SNTX8Y 1/4" 0.281 0.625 0.110 0.090 100 5700 6.10

31SNTX8Y 5/16" 0.344 0.688 0.110 0.090 100 5000 7.00

37SNTX8Y 3/8" 0.406 0.812 0.126 0.110 100 3100 11.45

43SNTX8Y 7/16" 0.469 0.921 0.126 0.110 100 2400 14.95 50SNTX8Y 1/2" 0.531 1.062 0.188 0.156 100 1200 29.45

56SNTX8Y 9/16" 0.594 1.156 0.188 0.156 100 900 34.20

62SNTX8Y 5/8" 0.656 1.312 0.195 0.170 50 700 46.60

75SNTX8Y 3/4" 0.812 1.469 0.195 0.170 50 600 51.90 87SNTX8Y 7/8" 0.938 1.750 0.265 0.235 25 300 109.50 100SNTX8Y 1" 1.062 2.000 0.265 0.235 25 200 140.21

WASHERS HARDENED FLAT - SAE “NTX” EXTRA THICK PATTERN


1/4 S

NTX


WASHERS LOW CARBON STEEL - 1/8” EXTRA THICK FENDERZINC CLEAR FINISH - LOW CARBON STEEL



MAXTHICK

MINTHICK

PACKAGEQUANTITY

1/4 KEGQUANTITY


10X100XFW2Z 3/16" 0.219 1.000 0.132 0.108 100 1700 23.50

25X100XFW2Z 1/4" 0.281 1.000 0.132 0.108 100 1700 23.0025X125XFW2Z 1/4” 0.281 1.250 0.132 0.108 100 1100 36.50

25X150XFW2Z 1/4”" 0.281 1.500 0.132 0.108 100 700 57.5031X125XFW2Z 5/16” 0.343 1.250 0.132 0.108 100 1250 23.5031X150XFW2Z 5/16" 0.343 1.500 0.132 0.108 100 650 59.00

37X125XFW2Z 3/8" 0.406 1.250 0.132 0.108 50 1100 36.5037X150XFW2Z 3/8" 0.406 1.500 0.132 0.108 50 750 51.50

37X200XFW2Z 3/8” 0.406 2.00 0.132 0.108 50 400 100.0050X200XFW2Z 1/2" 0.531 2.000 0.132 0.108 25 425 65.80



TECHNICAL DRAWINGS

TECHNICAL DRAWINGS

If you have questions regarding any of our products, please contact ourcustomer service line at 440.350.1430. We will be glad to help!



TECHNICAL DRAWINGS

GRADE 8 ROUND HEAD SQUARE NECK CARRIAGE BOLTS - FULL THREAD

H

P

RO

Q

AL

NominalSize or

Basic BoltDiameter

E A H O P Q R

BodyDiameter

HeadDiameter

HeadHeight

SquareWidth

SquareDepth

CornerRadius

onSquare

FilletRadius

Max Min Max Min Max Min Max Min Max Min Max Max5/8-11” 0.642 0.559 1.344 1.219 0.344 0.313 0.642 0.616 0.344 0.313 0.078 0.0623/4-10” 0.768 0.678 1.594 1.469 0.406 0.375 0.768 0.741 0.406 0.375 0.078 0.062

SPECIFICATIONSMATERIAL: GRADE 8 PER SAE J429TENSILE STRENGTH: 150,000 PSI MIN

DIMENSIONS: ASME B18.5 ROUND HEAD SQUARE NECKTHREAD LENGTH: FULLY THREADED

FINISH: PLAIN & OIL

CATALOG PAGE(S): 2



TECHNICAL DRAWINGS

GRADE 8 #3 DOME HEAD PLOW BOLTS

1 5 0 M P S I

H

F

1 5 0 M P S I

B

CR

AS

FR

D

N

L

NomSizeor

BasicBolt

Dia

D A F H S FR CR CR B

BodyDiameter

HeadDiameter

FeedThickness

DomeHeight

Depthof

Square

FilletRadius

CornerRadius

TransAng

WidthAcross

Flats

Max Min Max Min Max Min Max Min Max Min Max Min Max Min Nom Max Min5/8-11” 0.625 0.611 1.044 1.013 0.120 0.050 0.100 0.070 0.516 0.466 0.062 0.015 0.094 0.030 30

deg0.640 0.625

3/4-10” 0.750 0.735 1.200 1.169 0.160 0.090 0.110 0.080 0.581 0.541 0.125 0.031 0.109 0.030 0.765 0.750


DIMENSIONS: #3 DOME HEAD ASME B18.9THREAD LENGTH: ASME B18.9 (2XDIAMETER+1/4” MIN)

FINISH: PLAIN & OIL

CATALOG PAGE(S): 3

L = +/- 0.12 inch



TECHNICAL DRAWINGS

GRADE 5 HEX FLANGE SCREWS

ER1

B

F

15-30°

LT

H

U

K

G

NominalSize or

Basic BoltDiameter

F G B E H U K R1

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

BodyDiameter

Heightof

Head

FlangeThick ness

WrenchHeight Fillet

Max Min Max Min Max Max Min Max Min Min Min

1/4 0.375 0.367 0.433 0.409 0.56 0.2500 0.2450 0.28 0.04 0.17 0.015

5/16 0.500 0.489 0.577 0.548 0.68 0.3125 0.3065 0.32 0.05 0.21 0.0153/8 0.562 0.551 0.650 0.618 0.81 0.3750 0.3690 0.39 0.06 0.25 0.0151/2 0.750 0.736 0.866 0.825 1.07 0.5000 0.4930 0.51 0.08 0.34 0.015


DIMENSIONS: IFI-111 (2014)FINISH: ZINC CLEAR CR+3

CATALOG PAGE(S): 4

Diameter Length Full Thread Length Patial Thread “LT” Partial Thread Length1/4 THROUGH 1-1/4” 1-3/8“ & LONGER Min 0.750”

5/16 THROUGH 1-3/8” 1-1/2” & LONGER Min 0.875”3/8 THROUGH 1-1/2” 1-5/8” & LONGER Min 1.000”1/2 THROUGH 1-7/8” 2” & LONGER Min 1.250” T h

r e a

d L e n g

t h



TECHNICAL DRAWINGS

GRADE 8 HEX FLANGE SCREWS

ER1

B

F

15-30°

LT

H

U

K

G

NominalSize or

Basic BoltDiameter

F G B E H U K R1

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

BodyDiameter

Heightof

Head

FlangeThick ness

WrenchHeight Fillet

Max Min Max Min Max Max Min Max Min Min Min1/4 0.375 0.367 0.433 0.409 0.56 0.2500 0.2450 0.28 0.04 0.17 0.015

5/16 0.500 0.489 0.577 0.548 0.68 0.3125 0.3065 0.32 0.05 0.21 0.0153/8 0.562 0.551 0.650 0.618 0.81 0.3750 0.3690 0.39 0.06 0.25 0.015

7/16 0.625 0.612 0.722 0.685 0.93 0.4375 0.4305 0.46 0.07 0.30 0.0151/2 0.750 0.736 0.866 0.825 1.07 0.5000 0.4930 0.51 0.08 0.34 0.0155/8 0.937 0.922 1.083 1.034 1.33 0.6250 0.6170 0.62 0.10 0.42 0.0203/4 1.125 1.100 1.299 1.234 1.59 0.7500 0.7410 0.73 0.11 0.51 0.020


DIMENSIONS: IFI-111 (2014)FINISH: PHOSPHATE & OIL

CATALOG PAGE(S): 5-8

Diameter Length Full Thread Length Partial Thread “LT” Partial Thread Length1/4” THROUGH 1-1/4” 1-3/8“ & LONGER Min 0.750”

5/16” THROUGH 1-3/8” 1-1/2” & LONGER Min 0.875”3/8” THROUGH 1-1/2” 1-5/8” & LONGER Min 1.000”

7/16” THROUGH 1-3/4” 1-7/8” & LONGER Min 1.125”1/2” THROUGH 1-7/8” 2” & LONGER Min 1.250”5/8” THROUGH 2-1/2” 2-5/8” & LONGER Min 1.500”3/4” THROUGH 2-3/4” 2-7/8” & LONGER Min 1.750”

T h r e a

d L e n g

t h



TECHNICAL DRAWINGS

GRADE 5 SERRATED HEX FLANGE SCREWS

B1B

F

15-30°

H

U

K 24 TEETHCLOCKWISE

R1

G

NominalSize or

Basic BoltDiameter

F G B H U K B1 R1

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

Heightof

Head

FlangeThick ness

WrenchHeight

SerrationDepth Fillet

Max Min Max Min Max Max Min Min Min Min#6 0.250 0.244 0.297 0.272 0.350 0.154 0.027 0.090 0.006 0.011#8 0.250 0.244 0.297 0.272 0.374 0.181 0.027 0.114 0.006 0.011

#10 0.312 0.305 0 .368 0.340 0.454 0.209 0.031 0.134 0.009 0.0111/4 0.375 0.367 0.433 0.409 0.56 0.28 0.04 0.17 0.011 0.015

5/16 0.500 0.489 0.577 0.548 0.68 0.32 0.05 0.21 0.013 0.0153/8 0.562 0.551 0.650 0.618 0.81 0.39 0.06 0.25 0.015 0.015

7/16 0.625 0.612 0.722 0.685 0.93 0.46 0.07 0.30 0.018 0.0151/2 0.750 0.736 0.866 0.825 1.07 0.51 0.08 0.34 0.019 0.0155/8 0.937 0.922 1.083 1.034 1.33 0.62 0.10 0.42 0.020 0.020


DIMENSIONS: IFI-111 (2014) SERRATEDTHREAD LENGTH: FULLY THREADED

SHEAR CUT MACHINE SCREW THREADS PER ASME B18.6.3FINISH: ZINC CLEAR CR+3




TECHNICAL DRAWINGS

GRADE 8 SERRATED HEX FLANGE SCREWS

B1B

F

15-30°

H

U

K 24 TEETHCLOCKWISE

R1

G

NominalSize or

Basic BoltDiameter

F G B H U K B1 R1

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

Heightof

Head

FlangeThick ness

WrenchHeight


Max Min Max Min Max Max Min Min Min Min1/4 0.375 0.367 0.433 0.409 0.56 0.28 0.04 0.17 0.011 0.015

5/16 0.500 0.489 0.577 0.548 0.68 0.32 0.05 0.21 0.013 0.0153/8 0.562 0.551 0.650 0.618 0.81 0.39 0.06 0.25 0.015 0.015


DIMENSIONS: IFI-111 (2014) SERRATEDTHREAD LENGTH: FULLY THREADED


CATALOG PAGE(S): 12



TECHNICAL DRAWINGS

18-8 (304) STAINLESS STEEL SERRATED HEX FLANGE SCREWS

F593C

B1B

F

15-30°

H

U

K 24 TEETHCLOCKWISE

R1

F593CG

NominalSize or

Basic BoltDiameter

F G B H U K B1 R1

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

Heightof

Head

FlangeThick ness

WrenchHeight



5/16 0.500 0.489 0.577 0.548 0.68 0.32 0.05 0.21 0.013 0.0153/8 0.562 0.551 0.650 0.618 0.81 0.39 0.06 0.25 0.015 0.015

SPECIFICATIONSMATERIAL: 18-8 (304) STAINLESS STEEL

TENSILE STRENGTH: 100,000 - 150,000 PSIDIMENSIONS: IFI-111 (2014) - FULLY THREADED - SERRATED

MECHANICAL PROPERTIES: 304, CONDITION CW OF ASTM F593CSHEAR CUT MACHINE SCREW THREADS PER ASME B18.6.3

FINISH: PASSIVATED

CATALOG PAGE(S): 13



TECHNICAL DRAWINGS

GRADE 5 HEX LARGE SERRATED FLANGE SCREWS

B1B

F

15-30°

H

U

K

24 TEETHCLOCKWISE

R1

G

NominalSize or

Basic BoltDiameter

F G B H U K B1 R1

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

Heightof

Head

FlangeThick ness

WrenchHeight



5/16 0.500 0.489 0.577 0.548 0.820 0.32 0.05 0.21 0.013 0.0153/8 0.562 0.551 0.650 0.618 0.915 0.39 0.06 0.25 0.015 0.015

CATALOG PAGE(S): 14


DIMENSIONS: IFI-111 (2014) SERRATED LARGE FLANGETHREAD LENGTH: FULLY THREADED




TECHNICAL DRAWINGS

GRADE 2 HEX FLANGE LAG SCREWS

H

UK

L

Gimlet Point

SEE NOTE

D 60° approx

B

F

15°-25°

G

1 5°-25°

0-6 INCHES ± 0.12OVER 6 INCHES ± 0.25

NOTE:Minimum thread length is 1/2 length of the screw plus 0.50” or 6” whichever is shorter.Screws too short for the formula shall be threaded as close to the head as practicable.

R1R2

NominalSize orBasicBolt

Diameter

F G B H U K D R1 R2

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

Heightof

Head

FlangeThick ness

WrenchHeight

BodyDiameter Fillet Fillet

Max Min Max Min Max Max Min Min Max Min Max Max1/4 0.375 0.367 0.433 0.409 0.56 0.28 0.04 0.17 0.260 0.237 0.015 0.030

5/16 0.500 0.489 0.577 0.548 0.68 0.32 0.05 0.21 0.324 0.298 0 .019 0.0303/8 0.562 0.551 0.650 0.618 0.81 0.39 0.06 0.25 0.388 0.360 0.022 0.0301/2 0.750 0.736 0.866 0.825 1.07 0.51 0.08 0.34 0.515 0.482 0.030 0.030

CATALOG PAGE(S): 15

SPECIFICATIONSMATERIAL: STEEL AISI 1006-1022 OR EQUIVALENT

TENSILE STRENGTH: 60,000 PSI MINHARDNESS: ROCKWELL B70-B100

FLANGE HEAD DIMENSIONS: IFI-111 (2014)LAG THREAD: PER ASME B18.2.1

FINISH: HOT DIP GALVANIZED PER ASTM A153

Thread Dimensions

S c r e w Thread

PerInch

PitchP

WidthFlat

B

ThreadDepth

T

RootDiameter

D11/4 10 0.100 0.043 0.039 0.173

5/16 9 0.111 0.048 0.043 0.2273/8 7 0.143 0.062 0.055 0.2651/2 6 0.167 0.072 0.064 0.371

B

T

DETAIL OF THREADS

60°

P

D1



TECHNICAL DRAWINGS

GRADE 5 HEX FLANGE NUTS

B

F

K

J

H

G

NominalSize or

Basic BoltDiameter

F G B H J K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

NutThickness

WrenchHeight

FlangeThick ness

Max Min Max Min Max Min Max Min Min Min1/4 0.438 0.428 0.505 0.488 0.594 0.574 0.236 0.222 0.14 0.04

5/16 0.500 0.489 0.577 0.557 0.680 0.660 0.283 0.268 0.17 0.043/8 0.562 0.551 0.650 0.628 0.750 0.728 0.347 0.330 0.23 0.04

7/16 0.688 0.675 0.794 0.768 0.937 0.910 0.395 0.375 0.26 0.041/2 0.750 0.736 0.866 0.840 1.031 1.000 0.458 0.437 0.31 0.055/8 0.938 0.922 1.083 1.051 1.281 1.248 0.569 0.545 0.40 0.05

SPECIFICATIONSMATERIAL: GRADE 5 PER SAE J995

HARDNESS: 32 HRC MAXDIMENSIONS: IFI-145 (2002) OR ASME B18.2.2 (2011)

FINISH: ZINC CLEAR CR+3

CATALOG PAGE(S): 16



TECHNICAL DRAWINGS

GRADE 8 HEX FLANGE NUTS

B

F

K

J

H

G

NominalSize or

Basic BoltDiameter

F G B H J K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

NutThickness

WrenchHeight

FlangeThick ness


5/16 0.500 0.489 0.577 0.557 0.680 0.660 0.283 0.268 0.17 0.043/8 0.562 0.551 0.650 0.628 0.750 0.728 0.347 0.330 0.23 0.04

7/16 0.688 0.675 0.794 0.768 0.937 0.910 0.395 0.375 0.26 0.041/2 0.750 0.736 0.866 0.840 1.031 1.000 0.458 0.437 0.31 0.055/8 0.938 0.922 1.083 1.051 1.281 1.248 0.569 0.545 0.40 0.053/4 1.125 1.088 1.299 1.240 1.500 1.460 0.675 0.627 0.46 0.06


HARDNESS: 1/4”-5/8” 24-32HRC & 3/4” 26-34HRCDIMENSIONS: IFI-145 (2002) OR ASME B18.2.2 (2011)

FINISH: PHOSPHATE & OIL

CATALOG PAGE(S): 16



TECHNICAL DRAWINGS

CASE HARDENED HEX SERRATED FLANGE NUTS

B

F

K

J

H

G

NominalSize or

Basic BoltDiameter

F G B H J K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

NutThickness

WrenchHeight

FlangeThick ness

Max Min Max Min Max Min Max Min Min Min#6 0.312 0.302 0.361 0.342 0.422 0.406 0.171 0.156 0.10 0.02#8 0.344 0.334 0.397 0.381 0.469 0.452 0.203 0.187 0.13 0.02

#10 0.375 0.365 0.433 0.416 0.500 0.480 0.219 0.203 0.13 0.031/4 0.438 0.428 0.505 0.488 0.594 0.574 0.236 0.222 0.14 0.04

5/16 0.500 0.489 0.577 0.557 0.680 0.660 0.283 0.268 0.17 0.043/8 0.562 0.551 0.650 0.628 0.750 0.728 0.347 0.330 0.23 0.04

7/16 0.688 0.675 0.794 0.768 0.937 0.910 0.395 0.375 0.26 0.041/2 0.750 0.736 0.866 0.840 1.031 1.000 0.458 0.437 0.31 0.055/8 0.938 0.922 1.083 1.051 1.281 1.248 0.569 0.545 0.40 0.053/4 1.125 1.088 1.299 1.240 1.500 1.460 0.675 0.627 0.46 0.06

SPECIFICATIONSMATERIAL: CARBON STEEL - CASE HARDENED

SURFACE HARDNESS: R15N 79/86DIMENSIONS: IFI-145 (2002) OR ASME B18.2.2 (2011)


CATALOG PAGE(S): 17



TECHNICAL DRAWINGS

CASE HARDENED HEX LARGE SERRATED FLANGE NUTS

B

F

K

J

H

G

NominalSize or

Basic BoltDiameter

F G B H J K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

NutThickness

WrenchHeight

FlangeThick ness


5/16 0.500 0.489 0.577 0.557 0.820 0.790 0.375 0.343 0.20 0.043/8 0.562 0.551 0.650 0.628 0.915 0.885 0.406 0.390 0.24 0.041/2 0.750 0.736 0.866 0.840 1.205 1.175 0.515 0.485 0.29 0.06

SPECIFICATIONSMATERIAL: CARBON STEEL - CASE HARDENED

SURFACE HARDNESS: R15N 79/86DIMENSIONS: IFI-145 (2002) OR ASME B18.2.2 (2011)


CATALOG PAGE(S): 17



TECHNICAL DRAWINGS

GRADE 5 HEX SERRATED FLANGE NUTS

B

F

K

G

J

H


HARDNESS: 32 HRC MAXDIMENSIONS: IFI-145 (2002) OR ASME B18.2.2 (2011) W/ SERRATIONS


CATALOG PAGE(S): 18

NominalSize or

Basic BoltDiameter

F G B H J K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

NutThickness

WrenchHeight

FlangeThick ness


5/16 0.500 0.489 0.577 0.557 0.680 0.660 0.283 0.268 0.17 0.043/8 0.562 0.551 0.650 0.628 0.750 0.728 0.347 0.330 0.23 0.04

7/16 0.688 0.675 0.794 0.768 0.937 0.910 0.395 0.375 0.26 0.041/2 0.750 0.736 0.866 0.840 1.031 1.000 0.458 0.437 0.31 0.05



TECHNICAL DRAWINGS

GRADE 8 HEX SERRATED FLANGE NUTS

B

F

G

K

J

H


HARDNESS: 1/4”-5/8” 24-32HRC & 3/4” 26-34HRCDIMENSIONS: IFI-145 (2002) OR ASME B18.2.2 (2011)

FINISH: PLAIN & OIL

CATALOG PAGE(S): 18

NominalSize or

Basic BoltDiameter

F G B H J K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

NutThickness

WrenchHeight

FlangeThick ness

Max Min Max Min Max Min Max Min Min Min

1/4 0.438 0.428 0.505 0.488 0.594 0.574 0.236 0.222 0.14 0.045/16 0.500 0.489 0.577 0.557 0.680 0.660 0.283 0.268 0.17 0.043/8 0.562 0.551 0.650 0.628 0.750 0.728 0.347 0.330 0.23 0.041/2 0.750 0.736 0.866 0.840 1.031 1.000 0.458 0.437 0.31 0.055/8 0.938 0.922 1.083 1.051 1.281 1.248 0.569 0.545 0.40 0.053/4 1.125 1.088 1.299 1.240 1.500 1.460 0.675 0.627 0.46 0.06



TECHNICAL DRAWINGS

18-8 (304) STAINLESS STEEL HEX SERRATED FLANGE NUTS

B

F

K

J

H

G

NominalSize or

Basic BoltDiameter

F G B H J K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

NutThickness

WrenchHeight

FlangeThick ness


5/16 0.500 0.489 0.577 0.557 0.820 0.790 0.375 0.343 0.20 0.043/8 0.562 0.551 0.650 0.628 0.915 0.885 0.406 0.390 0.24 0.04

SPECIFICATIONSMATERIAL: 18-8 (304) STAINLESS STEEL

DIMENSIONS: IFI-145 (2002) OR ASME B18.2.2 (2011) W/SERRATIONSMECHANICAL PROPERTIES: 304, GROUP 1 CW OF ASTM F594

FINISH: PASSIVATED

CATALOG PAGE(S): 19



TECHNICAL DRAWINGS

GRADE G HEX FLANGE LOCK NUTS

B

FK

J

H

G

SPECIFICATIONSMATERIAL: GRADE G (GRADE 8 EQUIVALENT)

PREVAILING TORQUE: IFI-100/107PROOF LOAD: PER IFI-100

DIMENSIONS: PER IFI-100/107FINISH: PHOSHPATE & OIL

CATALOG PAGE(S): 20

NominalSize or

Basic BoltDiameter

F B H J K

WidthAcross

Flats

FlangeDia

NutThickness

WrenchHeight

FlangeThick ness

Nom Max Min Max Max Min Min Min

1/4 7/16 0.4385 0.428 0.560 0.300 0.265 0.14 0.045/16 1/2 0.5020 0.489 0.680 0.365 0.320 0.17 0.053/8 9/16 0.5645 0.551 0.810 0.425 0.404 0.20 0.06

7/16 11/16 0.6895 0.675 0.930 0.495 0.457 0.23 0.071/2 3/4 0.7520 0.736 1.070 0.555 0.528 0.26 0.085/8 15/16 0.9395 0.922 1.330 0.690 0.646 0.32 0.103/4 1-1/8 1.1270 1.088 1.585 0.825 0.742 0.38 0.11



TECHNICAL DRAWINGS

GRADE F HEX NYLON INSERT FLANGE LOCK NUTS

B

FK

J

H

NYLON INSERT

COLOR: WHITE

SPECIFICATIONSMATERIAL: GRADE F (GRADE 5 EQUIVALENT)

PREVAILING TORQUE: IFI-100/107PROOF LOAD: PER IFI-100

DIMENSIONS: PER IFI-100/107FINISH: ZINC CLEAR CR+3

CATALOG PAGE(S): 20

NominalSize or

Basic BoltDiameter

F B H J K

WidthAcross

Flats

FlangeDia

NutThickness

WrenchHeight

FlangeThick ness

Max Min Max Max Min Min Min

1/4 0.438 0.428 0.560 0.300 0.265 0.14 0.045/16 0.502 0.489 0.680 0.365 0.320 0.17 0.053/8 0.564 0.551 0.810 0.425 0.404 0.20 0.061/2 0.752 0.736 1.070 0.555 0.528 0.26 0.085/8 0.939 0.922 1.330 0.690 0.646 0.32 0.10



TECHNICAL DRAWINGS

CLASS 8.8 HEX FLANGE SCREWS

8.8

E

B

F

15-30°

LT

H

U

K

8.8G

NominalSize or

Basic BoltDiameter

F G B E H U K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

BodyDiameter

Heightof

Head

FlangeThick ness

WrenchHeight

Max Min Min Max Max Min Max Min Min

M6-1.0 10.00 9.78 10.95 14.20 6.00 5.82 6.60 1.10 2.50

M8-1.25 13.00 12.73 14.26 18.00 8.00 7.78 8.10 1.20 3.20M10-1.5 15.00 14.73 16.50 22.30 10.00 9.78 9.20 1.50 3.60

M12-1.75 16.00 15.73 17.62 26.60 12.00 11.73 11.50 1.80 4.60

SPECIFICATIONSMATERIAL: CLASS 8.8 PER ISO 898-1

TENSILE STRENGTH: 800N/MM2 MINIMUMDIMENSIONS: PER DIN 6921 (1983)

FINISH: ZINC YELLOW CR+6

CATALOG PAGE(S): 21

DIAMETER FULL THREAD ORPARTIAL THREAD PARTIAL THREADPARTIAL THREAD COLUMN

MIN THREAD LENGTHM6 12mm through 20mm 25mm & LONGER► Min 18mmM8 16mm through 30mm 35mm & LONGER► Min 22mm

M10 20mm through 35mm 40mm & LONGER► Min 26mmM12 25mm through 40mm 45mm & LONGER► Min 30mm T

h r e a

d L e n g

t h



TECHNICAL DRAWINGS

CLASS 10.9 HEX FLANGE SCREWS

10.9

E

B

F

15-30°

LT

H

U

K

10.9G

NominalSize or

Basic BoltDiameter

F G B E H U K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

BodyDiameter

Heightof

Head

FlangeThick ness

WrenchHeight

Max Min Min Max Max Min Max Min MinM5-0.80 8.00 7.78 8.71 11.80 5.00 4.82 5.40 1.00 2.00M6-1.0 10.00 9.78 10.95 14.20 6.00 5.82 6.60 1.10 2.50

M8-1.25 13.00 12.73 14.26 18.00 8.00 7.78 8.10 1.20 3.20M10-1.5 15.00 14.73 16.50 22.30 10.00 9.78 9.20 1.50 3.60

M12-1.75 16.00 15.73 17.62 26.60 12.00 11.73 11.50 1.80 4.60M14-2.0 18.00 17.73 19.86 30.50 14.00 13.73 12.80 2.10 5.10M16-2.0 21.00 20.67 23.15 35.00 16.00 15.73 14.40 2.40 5.80


TENSILE STRENGTH: 1040N/MM2 MINIMUMDIMENSIONS: PER DIN 6921 (1983)

FINISH: PHOSPHATE & OIL


DIAMETER FULL THREAD ORPARTIAL THREAD LENGTH PARTIAL THREADPARTIAL THREAD COLUMN

MIN THREAD LENGTHM5 THROUGH 20mm 25mm & LONGER ► Min 16mmM6 THROUGH 20mm 25mm & LONGER► Min 18mmM8 THROUGH 30mm 35mm & LONGER► Min 22mm

M10 THROUGH 35mm 40mm & LONGER► Min 26mmM12 THROUGH 40mm 45mm & LONGER► Min 30mmM14 THROUGH 45mm 50mm & LONGER► Min 34mmM16 THROUGH 50mm 55mm & LONGER► Min 38mm

T h r e a

d L e n g

t h



TECHNICAL DRAWINGS

CLASS 8.8 SERRATED HEX FLANGE SCREWS

8.8

B1B

F

15-30°

H

U

K 24 TEETHCLOCKWISE

8.8G


TENSILE STRENGTH: 800N/MM2 MINIMUMDIMENSIONS: PER DIN 6921 (1983)THREAD LENGTH: FULLY THREADED


CATALOG PAGE(S): 25

NominalSize or

Basic BoltDiameter

F G B E H U K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

BodyDiameter

Heightof

Head

FlangeThick

ness

WrenchHeight

Max Min Min Max Max Min Max Min Min

M6-1.0 10.00 9.78 10.95 14.20 6.00 5.82 6.60 1.10 2.50M8-1.25 13.00 12.73 14.26 18.00 8.00 7.78 8.10 1.20 3.20

M10-1.5 15.00 14.73 16.50 22.30 10.00 9.78 9.20 1.50 3.60M12-1.75 16.00 15.73 17.62 26.60 12.00 11.73 11.50 1.80 4.60



TECHNICAL DRAWINGS

CLASS 10.9 JIS HEX FLANGE SCREWS

10.9

E

B

F

15-30°

LT

H

U

K

10.9G


TENSILE STRENGTH: 1040N/MM2 MINIMUMDIMENSIONS: PER JIS B1189 TYPE 2


CATALOG PAGE(S): 26

NominalSize or

Basic BoltDiameter

F G B E H U K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

BodyDiameter

Heightof

Head

FlangeThick ness

WrenchHeight

Max Min Min Max Max Min Max Min MinM6-1.0 10.00 9.80 11.05 14.00 6.00 5.90 6.00 0.80 3.60

M8-1.25 12.00 11.75 13.25 17.50 8.00 7.85 8.00 1.00 4.80M10-1.25 14.00 13.75 15.51 21.00 10.00 9.85 10.00 1.20 6.00

DIAMETER FULL THREADLENGTHPARTIAL THREAD

LENGTHPARTIAL THREADTHREAD LENGTH

M6 THROUGH 25mm 26mm & LONGER 18-21mmM8 THROUGH 30mm 31mm & LONGER 22-25mm

M10 THROUGH 35mm 36mm & LONGER 26-29mm



TECHNICAL DRAWINGS

CLASS 10 HEX FLANGE NUTS

1 0

B

F

K

J

H

G

1 0

NominalSize or

Basic BoltDiameter

F G B H J K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

NutThickness

WrenchHeight

FlangeThick ness

Max Min Max Min Max Max Min Min MinM6 10.00 9.78 11.55 11.05 14.20 6.00 5.70 3.10 1.10M8 13.00 12.73 15.01 14.38 17.90 8.00 7.60 4.50 1.20

M10 15.00 14.73 17.32 16.64 21.80 10.00 9.60 5.50 1.50M12 18.00 17.73 20.78 20.03 26.00 12.00 11.60 6.70 1.80M16 24.00 23.67 27.71 26.75 34.50 16.00 15.30 9.00 2.40

SPECIFICATIONSMATERIAL: CLASS 10 PER ISO 898-2

DIMENSIONS: DIN 6923FINISH: ZINC CLEAR CR+3

CATALOG PAGE(S): 27



TECHNICAL DRAWINGS

CLASS 10 HEX FLANGE LOCK NUTS

1 0

B

FK

J

H

G

1 0

NominalSize or

Basic BoltDiameter

F G B H J K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

NutThickness

WrenchHeight

FlangeThick ness


M10 15.00 14.73 17.32 16.64 21.80 11.40 9.60 5.50 1.50M12 18.00 17.73 20.78 20.03 26.00 13.80 11.60 6.70 1.80M14 21.00 20.67 24.25 23.35 29.90 15.90 13.30 7.80 2.10M16 24.00 23.67 27.71 26.75 34.50 18.30 15.30 9.00 2.40


DIMENSIONS: DIN 6927 PREVAILING TORQUEFINISH: PHOSPHATE & OIL

CATALOG PAGE(S): 27



TECHNICAL DRAWINGS

CLASS 8 SERRATED HEX FLANGE NUTS

8

K

J

HB

F

G

8

NominalSize or

Basic BoltDiameter

F G B H J K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

NutThickness

WrenchHeight

FlangeThick ness


M10 15.00 14.73 17.32 16.64 21.80 10.00 9.60 5.50 1.50M12 18.00 17.73 20.78 20.03 26.00 12.00 11.60 6.70 1.80


DIMENSIONS: DIN 6923 W/ SERRATIONSFINISH: ZINC CLEAR CR+3

CATALOG PAGE(S): 28



TECHNICAL DRAWINGS

CLASS 10 JIS HEX FLANGE NUTS

1 0

B

F

K

J

H

G

1 0

NominalSize or

Basic BoltDiameter

F G B H J K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

NutThickness

WrenchHeight

FlangeThick ness

Max Min Max Max Max Min Min MinM6 10.00 9.80 11.05 14.00 6.00 5.25 3.60 0.80M8 12.00 11.75 13.25 17.50 8.00 7.10 4.80 1.10

M10 14.00 13.75 15.51 21.00 10.00 9.10 6.00 1.20


DIMENSIONS: JIS B1190 (1987)FINISH: ZINC CLEAR CR+3

CATALOG PAGE(S): 28



TECHNICAL DRAWINGS

CLASS 10 JIS SERRATED HEX FLANGE NUTS

1 0

B

F

G

1 0

K

J

H


DIMENSIONS: JIS B1190 (1987) W/ SERRATIONSFINISH: ZINC CLEAR CR+3

CATALOG PAGE(S): 29

NominalSize or

Basic BoltDiameter

F G B H J K

WidthAcross

Flats

WidthAcross

Corners

FlangeDia

NutThickness

WrenchHeight

FlangeThick ness

Max Min Max Max Max Min Min MinM6 10.00 9.80 11.05 14.00 6.00 5.25 3.60 0.80M8 12.00 11.75 13.25 17.50 8.00 7.10 4.80 1.10

M10 14.00 13.75 15.51 21.00 10.00 9.10 6.00 1.20



TECHNICAL DRAWINGS

USS PATTERN “NT” HARDENED FLAT WASHERS

1/4 U

NT

C

SHARP EDGES TO BE FREE OF BURRSNT = WASHER TYPE

BOLT SIZEU = USS PATTERN

B

1/4 U

NT

A

NomBoltSize

Part Number

A B C

Inside Dia Outside Dia Thickness

Basic +TOL -TOL Basic +TOL -TOL Max Min1/4 25 UNT8Y 0.312 0.015 0.005 0.734 0.015 0.007 0.065 0.055

5/16 31 UNT8Y 0.375 0.015 0.005 0.875 0.030 0.007 0.080 0.0643/8 37 UNT8Y 0.438 0.015 0.005 1.000 0.030 0.007 0.080 0.064

7/16 43 UNT8Y 0.500 0.015 0.005 1.250 0.030 0.007 0.080 0.0641/2 50 UNT8Y 0.562 0.015 0.005 1.375 0.030 0.007 0.116 0.100

9/16 56 UNT8Y 0.625 0.015 0.005 1.469 0.030 0.007 0.116 0.1005/8 62 UNT8Y 0.688 0.030 0.007 1.750 0.030 0.007 0.138 0.1223/4 75 UNT8Y 0.812 0.030 0.007 2.000 0.030 0.007 0.138 0.1227/8 87 UNT8Y 0.938 0.030 0.007 2.250 0.030 0.007 0.160 0.136

1 1 00UNT8Y 1.062 0.030 0.007 2.500 0.030 0.007 0.160 0.136

SPECIFICATIONSMATERIAL: 1035 OR BETTER STEEL

HARDNESS: 38-45HRC THROUGH HARDENEDMECHANICAL & PHYSICAL REQUIREMENTS: PER ASTM F-436


CATALOG PAGE(S): 30



TECHNICAL DRAWINGS

SAE PATTERN “NT” HARDENED FLAT WASHERS

1/4 S

NT

C

SHARP EDGES TO BE FREE OF BURRSNT = WASHER TYPE

BOLT SIZES = SAE PATTERN

B

1/4 S

NT

A

NomBoltSize

Part Number

A B C


Basic +TOL -TOL Basic +TOL -TOL Max Min1/4 25 SNT8Y 0.281 0.015 0.005 0.625 0.015 0.005 0.065 0.055

5/16 31 SNT8Y 0.344 0.015 0.005 0.688 0.015 0.007 0.065 0.0553/8 37 SNT8Y 0.406 0.015 0.005 0.812 0.015 0.007 0.065 0.055

7/16 43 SNT8Y 0.469 0.015 0.005 0.921 0.015 0.007 0.065 0.0551/2 50 SNT8Y 0.531 0.015 0.005 1.062 0.030 0.007 0.116 0.100

9/16 56 SNT8Y 0.594 0.015 0.005 1.156 0.030 0.007 0.116 0.1005/8 62 SNT8Y 0.656 0.030 0.007 1.312 0.030 0.007 0.138 0.1223/4 75 SNT8Y 0.812 0.030 0.007 1.469 0.030 0.007 0.138 0.1227/8 87 SNT8Y 0.938 0.030 0.007 1.750 0.030 0.007 0.152 0.136

1 1 00SNT8Y 1.062 0.030 0.007 2.000 0.030 0.007 0.160 0.136




CATALOG PAGE(S): 30



TECHNICAL DRAWINGS

USS PATTERN “NT2” THICK HARDENED FLAT WASHERS

1/4 U

NT2

C

SHARP EDGES TO BE FREE OF BURRSNT2 = WASHER TYPE

BOLT SIZEU = USS PATTERN

B

1/4 U

NT2

A

NomBoltSize

Part Number

A B C


Basic +TOL -TOL Basic +TOL -TOL Max Min1/4 25 UNT28Y 0.312 0.015 0.005 0.734 0.015 0.007 0.080 0.064

5/16 31 UNT28Y 0.375 0.015 0.005 0.875 0.030 0.007 0.093 0.0793/8 37 UNT28Y 0.438 0.015 0.005 1.000 0.030 0.007 0.093 0.079

7/16 43 UNT28Y 0.500 0.015 0.005 1.250 0.030 0.007 0.106 0.0901/2 50 UNT28Y 0.562 0.015 0.005 1.375 0.030 0.007 0.146 0.122

9/16 56 UNT28Y 0.625 0.015 0.005 1.469 0.030 0.007 0.146 0.1225/8 62 UNT28Y 0.688 0.030 0.007 1.750 0.030 0.007 0.160 0.1363/4 75 UNT28Y 0.812 0.030 0.007 2.000 0.030 0.007 0.160 0.1367/8 87 UNT28Y 0.938 0.030 0.007 2.250 0.030 0.007 0.160 0.136

1 1 00UNT28Y 1.062 0.030 0.007 2.500 0.030 0.007 0.160 0.136




CATALOG PAGE(S): 31



TECHNICAL DRAWINGS

SAE PATTERN “NT2” THICK HARDENED FLAT WASHERS

1/4 S

NT2

C

SHARP EDGES TO BE FREE OF BURRSNT2 = WASHER TYPE


B

1/4 S

NT2

A

NomBoltSize

Part Number

A B C


Basic +TOL -TOL Basic +TOL -TOL Max Min1/4 25 SNT28Y 0.281 0.015 0.005 0.625 0.015 0.005 0.080 0.064

5/16 31 SNT28Y 0.344 0.015 0.005 0.688 0.015 0.007 0.093 0.0793/8 37 SNT28Y 0.406 0.015 0.005 0.812 0.015 0.007 0.093 0.079

7/16 43 SNT28Y 0.469 0.015 0.005 0.921 0.015 0.007 0.106 0.0901/2 50 SNT28Y 0.531 0.015 0.005 1.062 0.030 0.007 0.146 0.122

9/16 56 SNT28Y 0.594 0.015 0.005 1.156 0.030 0.007 0.146 0.1225/8 62 SNT28Y 0.656 0.030 0.007 1.312 0.030 0.007 0.160 0.1363/4 75 SNT28Y 0.812 0.030 0.007 1.469 0.030 0.007 0.160 0.1367/8 87 SNT28Y 0.938 0.030 0.007 1.750 0.030 0.007 0.160 0.136

1 1 00SNT28Y 1.062 0.030 0.007 2.000 0.030 0.007 0.160 0.136




CATALOG PAGE(S): 31



TECHNICAL DRAWINGS

SAE PATTERN “NTX” EXTRA THICK HARDENED FLAT WASHERS

1/4 S

NTX

C

SHARP EDGES TO BE FREE OF BURRSNTX = WASHER TYPE


B

1/4 S

NTX

A

NomBoltSize

Part Number

A B C

Inside Dia OStside Dia Thickness

Basic +TOL -TOL Basic +TOL -TOL Max Min1/4 25 SNTX8Y 0.281 0.015 0.005 0.625 0.015 0.005 0.090 0.110

5/16 31 SNTX8Y 0.344 0.015 0.005 0.688 0.015 0.007 0.090 0.1103/8 37 SNTX8Y 0.406 0.015 0.005 0.812 0.015 0.007 0.110 0.126

7/16 43 SNTX8Y 0.469 0.015 0.005 0.921 0.015 0.007 0.110 0.1261/2 50 SNTX8Y 0.531 0.015 0.005 1.062 0.030 0.007 0.156 0.188

9/16 56 SNTX8Y 0.594 0.015 0.005 1.156 0.030 0.007 0.156 0.1885/8 62 SNTX8Y 0.656 0.030 0.007 1.312 0.030 0.007 0.170 0.1953/4 75 SNTX8Y 0.812 0.030 0.007 1.469 0.030 0.007 0.170 0.1957/8 87 SNTX8Y 0.938 0.030 0.007 1.750 0.030 0.007 0.235 0.265

1 1 00SNTX8Y 1.062 0.030 0.007 2.000 0.030 0.007 0.235 0.265




CATALOG PAGE(S): 32



TECHNICAL DRAWINGS

1/8” EXTRA THICK FENDER WASHERS

C

SHARP EDGES TO BE FREE OF BURRS

B A

NomBoltSize

Part Number

A B C


Basic +TOL -TOL Basic +TOL -TOL Max Min3/16 10X100XFW2Z 0.219 0.015 0.005 1.000 0.015 0.005 0.132 0.1081/4 25X100XFW2Z 0.281 0.015 0.005 1.000 0.015 0.005 0.132 0.108

1/4 25X125XFW2Z 0.281 0.015 0.005 1.250 0.015 0.005 0.132 0.1081/4 25X150XFW2Z 0.281 0.015 0.005 1.500 0.015 0.005 0.132 0.108

5/16 31X125XFW2Z 0.343 0.015 0.005 1.250 0.015 0.007 0.132 0.1085/16 31X150XFW2Z 0.343 0.015 0.005 1.500 0.015 0.007 0.132 0.1083/8 37X125XFW2Z 0.406 0.015 0.005 1.250 0.015 0.007 0.132 0.1083/8 37X150XFW2Z 0.406 0.015 0.005 1.500 0.015 0.007 0.132 0.1083/8 37X200XFW2Z 0.406 0.015 0.005 2.000 0.015 0.007 0.132 0.1081/2 50X200 XFW2Z 0.531 0.015 0.005 2.000 0.015 0.007 0.132 0.108

SPECIFICATIONSMATERIAL: LOW CARBON STEEL


CATALOG PAGE(S): 32



TERMS & CONDITIONS

1. All orders are subject to National’s acceptance in the form of a printed or electronically transmitted order acknowledgement. Pricevalidity is effective at the time of quotation and is subject to change without notice.

2. Payment terms are 1% 10 net 30 days with approved credit. If credit is denied for any reason, Prepayment or C.O.D shipping maybe granted at the discretion of National’s credit department. Payment terms commence at the date of the invoice. If the purchaser failsto ful ll the terms of payment, National reserves the right to revoke or modify payment terms without notice. National reserves the rightto delay or cancel future orders or order releases if the purchaser fails to remain within the credit terms as set forth by National. Thepurchaser will be in default by failing to provide full payment within National’s payment terms. If in default, the purchaser will be liable forcollection costs including any reasonable attorney’s fees plus the costs and expenses of any legal action. Prepayment or C.O.D shippingmay be granted at the discretion of National’s credit department.

3. Freight terms are F.O.B. shipping point and all shipments will be shipped as “freight collect”. National bears no responsibility for anyadditional freight charges for any reason including extended or delayed transit times. Risk of loss or damage to products in transit shallbe the responsibility of the purchaser and the purchaser shall immediately notify the carrier in writing of such loss or damage. Title toshipments will pass onto the purchaser upon departure of the shipping point. National warrants that all shipments will be adequatelypacked for domestic shipments.

4. No product will be accepted for return without National’s prior written approval. Any approved cancellations require that National willbe fully reimbursed for all expenses incurred including but not limited to any purchase commitments it might have made, and such terms

of cancellation shall be solely within the discretion of National. A 20% restocking charge will be applied to credits covering the approvedreturn of material. All returns must be “freight prepaid” and are the responsibility of the purchaser. All returns must be in their originalcontainers bearing Nationals container labels.

5. In the event of any delay or failure in National’s performance due to any act of God, re, explosion, strike of any difference withworkmen, shortage of utilities, facility, materials of labor, delay in transportation, substantial increase in costs to National, breakdown oraccident, compliance with or other action taken to carry out the intent or purpose of any law or regulation, or any cause beyond National’sreasonable control., National shall have such additional time with which to perform as may be reasonably necessary under the circum-stances. This right to apportion its available inventory of products among its customers will be in such a manner as deemed to be equita-ble. Such event or events shall not result in any liability of National to the purchaser. 6. All products furnished hereunder shall be subjectto National’s standard practices, including, but not limited to variations of shipments of ten percent (10%) from original order quantity.

7. National warrants that the products furnished shall substantially conform to the relevant industry standards in effect at the time of orderacceptance. The foregoing warranties shall not apply if the products have been subject to abuse, misuse, negligence, accident, reuse,or modi cation. However, no warranty of suitability for any particular purpose, nor any representation of warranty, whether express or

implied, is made respecting said products or the production thereof, and in no event shall National be liable for damages, including butnot limited to incidental, special, consequential, or other damages arising out of or in connection with the uses of the products even ifNational has been advised of the possibility of any such damages.

8. National will replace, at the delivery point speci ed on the face hereof, any product furnished hereunder that is found to be defectiveor otherwise fails to conform, or at National’s option, it will repay the price paid for such product, plus any transportation charges paid bythe purchaser. Claims must be made within 30 days following delivery of the product to purchaser and National must be given a reason-able opportunity to investigate the cause of the claim. National accepts no liability for charges for sorting or rework performed by or forthe purchaser without prior written permission of National. Purchaser’s exclusive remedy for the failure of National to furnish conformingproducts or to any warranty is expressly limited to the replacement or repayment as provided for above and National shall not be liableto purchaser or anyone else for any other claims or damages, whether direct or indirect, consequential, or incidental. National’s liabilityfor any other breach of this contract shall be limited to the difference between the delivered price and the market prices of such goods atpurchaser’s destination at the time of such breach.

9. No terms or conditions other than those stated herein, whether contained in purchaser’s purchase order, shipping release, or other

document, and no written or oral agreement that purports to vary these terms and conditions shall be binding upon National. All repre-sentations, negotiations, and proposals made prior to the date of this order/quotation are merged herewith. Any waiver by National or anybreach of these terms and conditions shall not be construed as a waiver of any other breach.

10. Unless otherwise agreed upon in writing by both National and the purchaser, all electroplated or coated products are furnished inaccordance with commercial practices for electroplate or coating processes and are not represented or held out as meeting speci c con -sensus, government, original equipment, or any other coating standards. All thread-gauging requirements are applicable prior to plating/coating. After plating/coating, thread-gauging requirements must be agreed upon in writing by both National and the purchaser prior toquotation or supply of the product.

11. This Agreement shall be governed by the laws of the State of Ohio.

12. Any controversy that relates to this Purchase or the transactions contemplated hereby shall be litigated in the Lake County Court ofCommon Pleas, Lake County, Ohio.



NOTES


70/70

www.flangescrews.com

Documents

National Fasteners Catalog