8/13/2019 nashuatic printer
2/2
Copyright 2000 G054-8610
Printed in the Netherlands
EE GB
INSTALLING THE PAPER
TRAY
Caution
The paper tray does no t have a stopper. Whenpulling it out, be
careful not to pull it strongly. Ifyou do, the tray might fall and
cause personalinjury.
The default setting of the paper size is A4K(short-edge
feed).
If you want to use other sizes, set paper in theoptional
tray.
For more information about the paper sizes thatcan be set in the
paper tray, see Paper and OtherMedia Supported by this Printer in
the PrinterReference included as a PDF file on the CD-ROM.
Pull the paper tray out of the pri nter. Place it on aflat
surface.
TS4K140E
Load paper into the paper tray with the pri nt sideup.
TS4J150E
Important
Confirm that the top of the stack is not higher thanthe limit
mark inside the tray.
Confirm that the paper fits under the rear guide.
SELECTING THE PANEL
DISPLAY LANGUAGESelect a language following the
proceduresdescribed below. The message for the selectedlanguage
will appear on the panel display.
Note
The default setting is E nglish.
If you want to use the English panel display, thefollowing
procedures are unnecessary.
Turn on the printers power switch while
pressing the Menu( ) key, until the following
message appears on the panel display.
Language
English
Press thekeys until the language you wantto select appears on
the panel display.
Press the Enter( ) key.
Press the Enter( ) key.
The settings are applied and the ready message appears on the
paneldisplay.
PRINTING A TEST PAGEYou can check if the printer works properly
byprinting a test page ( configuration page).
However, you cannot check the connection betweenthe printer and
the computer by printing the testpage.
Check that the power switch is turned on.
Press the Menu( ) key.
The following message appears on the panel display.
Main Menu:
Job Control
Press thekeys until the following messageappears on the panel
display.
Main Menu:
List Print
Press the Enter( ) key.
The following message appears on the panel display.
List Print:
1.Config. page
Press the Enter( ) key.The following message appears on the
panel display.
Config. page:
Press Enter key
Press the Enter( ) key.
In a short time, the test printing will start.
Important
If you cannot complete the test printing correctly,check if an
error message appears on the paneldisplay. For more information
about errormessages, see Troubleshooting in the PrinterReference
included as a PDF file on the CD-ROM.
After installing the new toner cartridge, the firstfew pages
might be printed with light density. Ifdensity does not become
darker, seeTroubleshooting in the Printer Referenceincluded as a
PDF file on the CD-ROM.
CONNECTING THE PRINTER TO
A COMPUTERConnect the printer to a computer using aparallel
port.
Important
The parallel interfac e cable is not provided withthe prin ter.
It is your resp onsibility to provi dethe interface cable
appropriate for the compu teryou are us ing.
The pri nters parallel connection is a s tandardbi-directional
interface. It requires a standard36-pin parallel cable compliant
with IEEE1284and an available parallel port on your computer.
To avoid elec trical int erference, u se a shield edcable.
Note
Do not use a parallel cable more than 2.5 meters(8.2 feet)
long.
Turn off the printers power switch.
Turn the computer off.
Attach the interface cable to the interfaceconnector of the
printer. Secure the cable withthe metal fittings as shown in the
illustration.
TS4K170E
SETTING UP FOR PRINTINGPrinting requires installation of a
printer driverfor the operating system.
Reference
See Printer Drivers for the Printer in theSetup Guide.
If you want to install options, see InstallingOptions in the
Setup Guide.
Insert the paper tray into the printer until itstops.
TS4K160E
Turn the power switch off.
TS4K110E
off
on
Off
Important Rating voltage of the parallel interface connector
for the computer ; Max. DC5V.
