www.caleffi.us

StarMax™ collector mounting kits for tilt or fl ush mounting

© Copyright 201 Caleffi

INSTALLATION MANUAL

Function

Caleffi ’s NAS10006 mounting kit allows StarMax™ collectors to be tilt mounted. Collectors may be mounted to any roof, vertical wall, fascia board, pre-constructed rack or ground mount system. The StarMax™ collectors must be mounted to two horizontal Caleffi

rails or any U type strut rails (see illustration). The frame wall will accept the collector clip mounted along the collector sides without drilling or tapping so the integrity of the frame wall is not compromised. The optional rear extension tubes can be cut to length allowing proper elevation and orientation.

NAS10006 contents

Pivot shoes and collector clips are mill fi nshed and extruded from high tensile strength 6005-T5 aluminum. All stainless steel bolts, nuts and washer are made of 304 stainless steel materials and certifi ed to ASTM F593C and ASTM F594C standards.

6 — U mounts formed aluminum 5052-H32 2 — Pivot shoes extruded aluminum 6005-T5 4 — Collector clips extruded aluminum 6005-T5 8 — Bolts 3/8"-16 x 1” stainless steel ASTM F593C 6 — Bolts 3/8"-16 x 2” stainless steel ASTM F593C 14 — Washers 3/8" stainless steel SAE 30414 — Nuts 3/8"-16 stainless steel ASTM F594C

FunctionCaleffi ’s NAS10007 mounting kit allows StarMax™ collectors to be fl ush mounted to any elevated surface or ground mount system. The StarMax™ collectors must be mounted to two horizontal Caleffi

rails or suitable U type strut rails (see illustration). The frame wall will accept the collector clip mounted along the collector sides without drilling or tapping so the integrity of the frame wall is not compromised.

NAS10007 contents

Collector clips are mill fi nished extruded aluminum from 6005-T5 high tensile strength aluminum. All stainless steel bolts, nuts and washer are made of 304 stainless steel materials and certifi ed to ASTM F593C and ASTM F594C standards.

4 — Collector clips extruded aluminum 6005-T54 — Bolts 3/8"-16 x 1” stainless steel ASTM F593C4 — Washers 3/8" stainless steel SAE 3044 — Nuts 3/8"-16 stainless steel ASTM F594C

NAS10006 & NAS10007

NAS10006Tilt mounting kit

NAS10007Flush mounting kit

Collector clip

The tilt and fl ush mounting kits contain collector clips which have a unique concave shape with a hole in the center that when tightened, with supplied 3/8"-16 x 1" stainless steel bolt to rails, tension is formed on the bolt nut which keeps clip fastened securely.

Flush mounting

The flush mounting kit allows for parallel mounting on a sloped roof surface. This is achieved by placing two mounting rails to back of the collector and attaching with collector clips included in hardware kit shown below. Mounting rails and U mount 2" are available separately.

Strut nut& U Strut rail

Collector clip & bolt

Collector clip,bolt & nut

Four slot rail

U mount 2”

Tilt mountingThe tilt mounting kit allows for the collectors to be angled differently than the orientation of the surface they are secured to. This is achieved by placing two rails to the back of the collector and attaching the collector clips, pivot shoes and U mounts included in hardware kit shown below. The mounting rails and tilt extension tubes are available separately.

Collectorclip & bolt

Strut nut& U Strut rail

U mount 1”

Pivot shoebolt & nut

Collectorclip, bolt & nut

U mount 1”

Four slotrail

Hardware for flush mounting 4 — Collector clips extruded aluminum 6005-T5 4 — Bolts 3/8"-16 x 1” stainless steel ASTM F593C 4 — Washers 3/8" stainless steel SAE 304 4 — Nuts 3/8"-16 stainless steel ASTM F594C

Optional mounting rails and U mounts: 2 — NAS10040-1 58" rails for one collector 2 — NAS10040-2 108" rails for two collectors 4 — NAS10041 U mount 2" for attaching rails

Hardware installed for tilt mounting 6 — U mounts 1" formed aluminum 5052-H32 2 — Pivot shoes extruded aluminum 6005-T5 4 — Collector clips extruded aluminum 6005-T5 8 — Bolts 3/8"-16 x 1” stainless steel ASTM F593C 6 — Bolts 3/8"-16 x 2” stainless steel ASTM F593C 14 — Washers 3/8" stainless steel SAE 30414 — Nuts 3/8"-16 stainless steel ASTM F594COptional mounting rails and tilt extension tubes: 2 — NAS10040-1 58" rails for one collector 2 — NAS10040-2 108" rails for two collectors 2 — NAS10002 Tilt extension 72" tubes for each collector 2 — NAS10005 Tilt extension 144" tubes for each collector

We reserve the right to change our products and their relevant technical data, contained in this publication, at any time and without prior notice.

Caleffi North America, Inc. · 3883 W. Milwaukee Road · Milwaukee, WI 53208 · Tel: 414-238-2360 · Fax: 414-238-2366www.caleffi.us / sales@caleffi.com© Copyright 201 Caleffi North America, Inc.

Four slot or U Strut rail(not included)

Four slot or U Strut rail(not included)

Tilt extension tubes(not included)