N EW ! A gricultural P roducts Automotive, Commercial ... · Product Guide 2018 LU B R IC AN TS N EW ! A gricultural P roducts G uide *' $ J 1 MF B TF WJTJU X X X X X X N Z T UJL

FC12

ENGINE OILS • AUTOMOTIVE GEAR OILS • TRANSMISSION/POWER FLUIDS • GREASES • HYDRAULIC FLUIDS • INDUSTRIAL GAS ENGINE OILS • FUNCTIONAL PRODUCTS • COMPRESSOR LUBRICANTS

Automotive, Commercial & Industrial Product Guide

2018

LUBRICANTS

NEW! Agricultural

Products Guide

IFC2

i

Please visit www.www.mystiklubes.com for the mostup-to-date information on products or for Safety Data Sheets.

2018 EditionThis Mystik Lubricants product guide is your directory to Mystik fluids, greases and their applications.

Products are not available at all source points. Please check product availability and container sizes for your normal source point(s).

Technical information and assistance: Product Answer Line 800-248-4684 [email protected]

Pre-shipment inquiries: Order Management 800-331-4068, option 1 [email protected]

Pricing, availability, post-shipment inquiries: Customer Service 800-331-4068, option 2 [email protected]

Properties shown are based on typical values for the product only and do not constitute a specification. The information contained herein is subject to change without notice.

The information in this book is provided with no representations or warranties but with good faith on the basis of the most accurate information available; CITGO accepts no liability for content errors or omissions, or for damages as a result of relying on information contained within. Consult your owner’s manual for proper lubricant selection.

Mystik® lubricants are prohibited from being repackaged. The reprinting of Mystik® labels and other material is also prohibited.

© 2018 CITGO Petroleum Corporation. All rights reserved.

ii

TABLE OF CONTENTSENGINE OILSMystik® JT-8® Premium Gasoline Motor Oils . . . . . . . . . . . . 1Mystik® JT-8® Premium Gasoline Synthetic Motor Oils . . 2-3Mystik® JT-8® Synthetic Engine Oil 5W-40 . . . . . . . . . . . . 4-5Mystik® JT-8® Synthetic Blend Super Heavy Duty

Engine Oils Monogrades . . . . . . . . . . . . . . . . . . . . . . . . . 6Mystik® JT-8® Synthetic Blend Super Heavy Duty

Engine Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8Mystik® JT-8® Synthetic Blend Super Heavy Duty

Engine Oils SAE 10W-40 and SAE 15W-50. . . . . . . . . . . 9

SMALL ENGINE OILSMystik® JT-4® 2-Cycle Lawn and Garden Engine Oil . . . . . 10Mystik® JT-4® 2-Cycle Premium Outboard Engine Oil . . . . 11Mystik® JT-4® 2-Cycle Premium Plus Outboard

Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Mystik® JT-4® All-In-One Outboard Engine Oil . . . . . . . . . . 13Mystik® JT-4® Sea & Snow® 2-Cycle Engine Oil . . . . . . . . . 14Mystik® JT-4® Synthetic 2-Cycle Personal Watercraft

Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Mystik® JT-4® Synthetic 2-Cycle Snowmobile Engine Oil . . 16Mystik® JT-4® 4-Cycle Marine Engine Oils . . . . . . . . . . . . . 17Mystik® JT-4® Synthetic 4-Cycle Snowmobile Motor Oil

SAE 0W-40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Mystik® JT-4® Synthetic 4-Cycle All-Terrain Vehicle Motor Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Mystik® JT-4® Premium High Performance Lower Unit Gear Lubricant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

AUTOMOTIVE GEAR OILSMystik® JT-7® Extended Range Full Synthetic

Gear Lubricant SAE 75W-140 . . . . . . . . . . . . . . . . . 21-22Mystik® JT-7® Multi-Purpose Gear Lubricants . . . . . . . . . . 23Mystik® JT-7® Synthetic Blend SAE 75W-90 Gear Lubricant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25Mystik® SX-7000® Synthetic Fluids . . . . . . . . . . . . . . . 26-27Mystik® Universal Gear Lubricants . . . . . . . . . . . . . . . . . . 28

TRANSMISSION/POWER FLUIDSMystik® JT-5® Synthetic Blend TFX *NEW* . . . . . . . . . 29-30Mystik® JT-5® Tractor Trans-Hydraulic Fluid . . . . . . . . . 31-32Mystik® Multi-Purpose ATF . . . . . . . . . . . . . . . . . . . . . . . . . 33Mystik® Synthetic Blend Multi-Vehicle ATF . . . . . . . . . . 34-35Mystik® Lubricants Tenax® Fluids . . . . . . . . . . . . . . . . . . . . 36Mystik® Twin Disc Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

GREASESMystik® Centra-Lube™ Grease . . . . . . . . . . . . . . . . . . . . . 38Mystik® General Purpose Grease . . . . . . . . . . . . . . . . . . . 39Mystik® JT-6® High Performance Marine Grease . . . . . . . . 40Mystik® JT-6® Hi-Temp Greases . . . . . . . . . . . . . . . . . . 41-42

Mystik® JT-6® Hi-Temp Grease with Moly . . . . . . . . . . . . . . 43Mystik® JT-6® Synthetic Hi-Temp Greases . . . . . . . . . . 44-45Mystik® JT-6® Lo-Temp Extreme Grease . . . . . . . . . . . . . . 46Mystik® JT-6® Multi-Purpose Grease . . . . . . . . . . . . . . 47-48Mystik® JT-6® Super Heavy Duty 460 Grease . . . . . . . 49-50Mystik® JT-6® Synthetic Blend Grease . . . . . . . . . . . . . 51-52Mystik® Moly Grease . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Mystik® OG-5 Outside Gear Grease . . . . . . . . . . . . . . . . . 54Mystik® Red Lithium C . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

HYDRAULIC FLUIDSMystik® Anti-Leak Industrial Oil . . . . . . . . . . . . . . . . . . . . . 56Mystik® AW Hydraulic Oils . . . . . . . . . . . . . . . . . . . . . . . . . 57Mystik® AW/AL Hydraulic Oils . . . . . . . . . . . . . . . . . . . 58-59Mystik® Hydraulic Jack Oil . . . . . . . . . . . . . . . . . . . . . . . . . 60

INDUSTRIAL GAS ENGINE OILSMystik® Terra® 340 Gas Engine Oils . . . . . . . . . . . . . . . . . 61Mystik® Terra® 500 Gas Engine Oil SAE 15W-50 . . . . . . . . 62Mystik® Terra® Free Ashless Gas Engine Oils . . . . . . . . . . 63Mystik® TerraSynTM Irrigation Engine Oil . . . . . . . . . . . . . . 64

FUNCTIONAL PRODUCTSMystik® Bar and Chain Lubricant . . . . . . . . . . . . . . . . . . . . 65Mystik® Rock Drill Oil 150 . . . . . . . . . . . . . . . . . . . . . . . . . 66Mystik® Tuff-Torq EG® . . . . . . . . . . . . . . . . . . . . . . . . . . 67-68Mystik® Turbine Drip Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 69Mystik® ViscidLube® Oil Treatment . . . . . . . . . . . . . . . . . . . 70Mystik® Non-Detergent General Purpose Oils . . . . . . . . . . 71

COMPRESSOR LUBRICANTSMystik® Ammonia Compressor Oil 68 . . . . . . . . . . . . . . . . 72

AGRICULTURAL PRODUCTSMystik® JT-8® Premium Gasoline Motor Oils . . . . . . . . . . . . 73Mystik® JT-8® Premium Gasoline Synthetic Motor Oils . 74-75Mystik® JT-8® Synthetic Engine Oil 5W-40 . . . . . . . . . . 76-77Mystik® JT-8® Synthetic Blend Super Heavy Duty Engine Oils Monogrades . . . . . . . . . . . . . . . . . . . . . . . . 78Mystik® JT-8® Synthetic Blend Super Heavy Duty Engine Oils. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79-80Mystik® JT-8® Synthetic Blend Super Heavy Duty Engine Oils SAE 10W-40 and SAE 15W-50. . . . . . . . . . 81Mystik® JT-4® Synthetic 4-Cycle All-Terrain Vehicle Motor Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Mystik® JT-4® 2-Cycle Lawn and Garden Engine Oil . . . . . . 83Mystik® JT-7® Multi-Purpose Gear Lubricants . . . . . . . . . . . 84Mystik® Universal Gear Lubricant . . . . . . . . . . . . . . . . . . . . 85Mystik® JT-5® Synthetic Blend TFX *NEW* . . . . . . . . . 86-87Mystik® JT-5® Tractor Trans-Hydraulic Fluid. . . . . . . . . . 88-89Mystik® Multi-Purpose ATF . . . . . . . . . . . . . . . . . . . . . . . . . 90

ii

iii

Mystik® JT-6® Hi-Temp Greases . . . . . . . . . . . . . . . . . . 91-92Mystik® JT-6® Multi-Purpse Grease . . . . . . . . . . . . . . . . 93-94Mystik® JT-6® Super Heavy Duty 460 Grease . . . . . . . . 95-96Mystik® AW/AL Hydraulic Oils . . . . . . . . . . . . . . . . . . . . 97-98Mystik® AW Hydraulic Oils . . . . . . . . . . . . . . . . . . . . . . . . . 99Mystik® Hydraulic Jack Oil . . . . . . . . . . . . . . . . . . . . . . . . 100Mystik® TerraSyn™ Irrigation Engine Oil. . . . . . . . . . . . . . 101Mystik® Bar and Chain Lubricant . . . . . . . . . . . . . . . . . . . 102Mystik® Turbine Drip Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 103Mystik® Non-Detergent General Purpose Oils . . . . . . . . . 104Mystik® Lubricants Tenax® Fluids . . . . . . . . . . . . . . . . . . . 105

REFERENCE INFORMATIONSAE J300 & SAE J306 Viscosity Grades . . . . . . . . . . . . . 106Comparative Viscosity Classifications . . . . . . . . . . . . . . . 107Mystik® Grease Characteristics Chart . . . . . . . . . . . . . . . 108NLGI Grease Classifications . . . . . . . . . . . . . . . . . . . . . . 109ASTM D4950 Standard Classification and

Specifications for Automotive Service Greases . . . . . . 109Grease Thickener Compatibility Chart . . . . . . . . . . . . . . . 110Approximate Equivalence of Viscosity

Grading Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

PRODUCT INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

iii

TABLE OF CONTENTS—(Cont’d.)

Engi

ne O

ils

1

C I T G O P e t r o l e u m C o r p o r a t i o n • 8 0 0 / 2 4 8 - 4 6 8 4 • H o u s t o n , T e x a s • M a n u f a c t u r e d i n U S A

P R O D U C T I N F O R M A T I O N

M Y S T I K ® J T - 8 ® P R E M I U M G A S O L I N E M O T O R O I L S

Mystik JT-8 Premium Gasoline Motor Oils, with their advanced, fuel efficient synthetic blends formula, exceed the latest warranty requirements of car manufacturers for gasoline engines and meet the latest API Performance and Resource Conserving ratings. The premium quality detergent/dispersant formulation guards against sludge, reduces deposits and protects against rust, corrosion and wear. Mystik JT-8 Premium Gasoline Motor Oils provide optimum viscosity and thermal stability and are highly recommended for all carburetor-equipped or fuel-injected gasoline engines including turbocharged, supercharged and other high performance models. These products offer maximum protection against deposits and have superior durability. Even under severe service conditions you can have complete confidence that your engine oil is providing the fullest protection possible.

• The 5W-20, 5W30 and 10W-30 viscosity grades are recommended for applications calling for oils meeting ILSAC GF-5 and API SN Plus.

• All viscosity grades are licensed for API SN Plus and are backward compatible with prior service categories (SM, SL, SJ and SH).

• Special friction modifier provides increased fuel economy

• Multi-viscosity, thermally stable and durable formulation provides maximum year-round protection

Consult owner’s manual for fluid selection.

MYSTIK® JT-8® PREMIUM GASOLINE MOTOR OILS

Material Code 663013002 663012002 663011002

SAE Grade 5W-20 5W-30 10W-30 Gravity, ASTM D4052, °API 32.0 32.4 30.8 Pounds/Gallon at 60°F 7.20 7.19 7.26 Specific Gravity at 60°F 0.865 0.863 0.872 Viscosities: at -25°C, cP Max – – 5,820 at -30°C, cP Max 6,170 5,360 – at 40°C, cSt 49.2 60.0 67.5 at 100°C, cSt 8.3 9.9 10.1 Viscosity Index 144 151 134 Flash Point, ASTM D92, COC, °F (°C) 442 (228) 450 (232) 451 (233) Pour Point, ASTM D97, °F (°C) -33 (-36) -38 (-39) -33 (-36) Color, ASTM D1500 L3.5 L3.5 L3.5

TYPICAL PROPERTIES:

M 2 0 0 0 1

DESCRIPTION:

FEATURES:

D a t e 0 6 / 1 8

Mystik and JT-8 are registered trademarks protected by federal law. All other registered trademarks or trademarks are the property of their respective owners.


M20001

Engine Oils

22



M Y S T I K ® J T - 8 ® P R E M I U M G A S O L I N E S Y N T H E T I C M O T O R O I L S

Mystik JT-8 Premium Gasoline Synthetic Motor Oils are well-balanced combinations of today’s highest quality synthetic base stocks and contain an advanced additive system that meets stringent automotive specifications. They are designed to provide excellent protection in today’s high performance gasoline (including turbocharged and supercharged) engines in passenger cars, vans, sport utility vehicles, and light trucks. These synthetic engine oils demonstrate improved performance in today’s advanced engine designs, and are available in SAE 0W-20, 5W-20 and 5W-30 viscosity grades.

• Excellent low-temperature starting and pumpability characteristics

• High-temperature/high-shear properties well above conventional oils

• Lower volatility when compared to conventional oils

• Meets the most advanced emissions and fuel economy standards in the US gasoline engines

• Enhanced protection against varnish buildup and sludge formation in critical engine parts for top performance and long engine life

• Extended engine life due to control of wear and deposit formation

• Compatible with conventional and synthetic motor oils

• Mystik® JT-8® Premium Gasoline Synthetic SAE 0W-20 Approved GM dexos1® Gen2 License D10392HG121

• Mystik® JT-8® Premium Gasoline Synthetic SAE 5W-20 Approved GM dexos1® Gen2 License D10744HL121

• Mystik® JT-8® Premium Gasoline Synthetic SAE 5W-30 Approved GM dexos1® Gen2 License D10372HF121

Mystik JT-8 Premium Gasoline Synthetic Motor Oils are recommended for passenger cars, sport utility vehicles and light trucks operating on gasoline. They are also recommended for use in gasoline engines which have been converted to operate on compressed natural gas (CNG), liquified natural gas (LNG), and liquified petroleum gas (LPG-which includes propane and butane). Consult the vehicle owners manual for proper engine lubricant selection.

Mystik JT-8 Premium Gasoline Synthetic Motor Oils meet the performance requirements for the latest gasoline-fueled engine service ILSAC GF-5/Resource Conserving and API SN Plus and display the API Certification Mark and API Service Symbol. They have also demonstrated benefits in industry accepted fuel economy tests.

Mystik JT-8 Premium Gasoline Synthetic 0W-20 Motor Oil meets the GM dexos1® Gen2 specification and is recommended for Original Equipment Manufacturers (OEM) such as Toyota and Honda for some hybrid vehicle applications and a limited number of low temperature applications.

Mystik JT-8 Premium Gasoline Synthetic Motor Oil SAE 5W-30 meets the GM dexos1® Gen2 specification and provides excellent performance where GM4718M or GM6094M is referenced.

Note: Mystik JT-8 Premium Gasoline Synthetic Motor Oils are not recommended for use in diesel engines in passenger cars, vans or light trucks. Mystik JT-8 SHD Motor Oils are recommended for diesel applications.

DESCRIPTION:

FEATURES:

(Continued)

D a t e 0 6 / 1 8

M 2 0 0 8 2


M20082

(Continued)

Engi

ne O

ils

33



TYPICAL PROPERTIES:

MYSTIK® JT-8® PREMIUM GASOLINE SYNTHETIC MOTOR OILS

Material Code 663032002 663024002 663014002

SAE Grade 0W-20 5W-20 5W-30 Gravity, ASTM D4052, °API 35.0 34.5 34.2 Pounds Per Gallon 7.08 7.10 7.11Flash Point, ASTM D92, °F (°C), COC 220 (428) 442 (228) 450 (232)Low Temperature Cranking, ASTM D5293 Temperature, °F (°C) -28 (-35) -22 (-30) -22 (-30)Viscosity, cP 5,190 5,270 4,080Viscosity, ASTM D445, cSt at 140°C 46.0 52.0 58.5Viscosity, ASTM D 445, cSt at 100°C 8.5 8.7 10.5Viscosity Index, ASTM D2270 164 145 171Pour Point, ASTM D97, °F (°C) -33 (-36) -33 (-36) -27 (-33)Color, ASTM D1500 L3.5 L3.5 L3.5ILSAC GF-5 Yes Yes YesAPI SN Plus Yes Yes YesResource Conserving Yes Yes YesGM dexos1® Gen2 Approved Yes Yes Yes

D a t e 0 6 / 1 8 - ( C o n t i n u e d )


M 2 0 0 8 2



M20082

(Continued)

Engine Oils

44



M 2 0 0 7 3

Mystik® JT-8® Synthetic Engine Oil, SAE 5W-40 , full synthetic super heavy duty engine oil,engineered with proprietary additive technology, delivers an extra level of performance for both olderand newer engines. The careful balance of synthetic components gives improved fuel economy,improved cold temperature performance and improved engine drain interval optimization capabilities.Mystik® JT-8® Synthetic Engine Oil, SAE 5W-40 meets the API CK-4 requirements, which is anexcellent choice for equipment owners who need maximum engine durability, fuel efficiency, extendedoil service capability and superior cold weather start-up performance.

• Up to 3% fuel economy advantage over SAE 15W-40 viscosity grade oils• Improves cold cranking, extending starter/battery life and reducing dependency on block heaters, saving energy• Double the oil durability protection compared to conventional CJ-4 engine oils. Always follow OEM recommendations when extending oil drain intervals• Superior lubrication in extreme temperature ranges compared to conventional SAE 15W-40 viscosity grade oils.

API CK-4, CJ-4, CI-4 PLUS, CI-4, CH-4Caterpillar ECF-3Cummins CES 20086Detroit Diesel DFS 93K 222Volvo/Mack/Renault – VDS-4.5/EOS-4.5/RLD-4PaccarNavistar

DESCRIPTION:

FEATURES:

RECOMMENDEDFOR:

(Continued)

D a t e 0 6 / 1 8

M Y S T I K ® J T - 8 ® S Y N T H E T I CE N G I N E O I L , S A E 5 W - 4 0

Category

Mystick JT-8 Synthtic Blend

SHD 15W-40 API CJ-4

Mystick JT-8 10W-30

API CK-4

Mystick JT-8 15W-40

API CK-4

Mystick JT-8 5W-40

API CK-4

Back Serviceable Yes Yes Yes Yes

Oxidation Stability ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

Shear Stability ✔ ✔ ✔ ✔ ✔ ✔✔

Aeration Control ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

Wear Control ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

Fuel Efficiency ✔ ✔ ✔ ✔ ✔ ✔

Low Tempurature Start-up ✔ ✔ ✔ ✔ ✔ ✔ ✔

Compatible with API CJ-4 Oil Yes Yes Yes Yes


(Continued)

M20073

Engi

ne O

ils

55



D a t e 0 6 / 1 8 - ( C o n t i n u e d )

M 2 0 0 7 3

TYPICAL PROPERTIES:

MYSTIK® JT-8® SYNTHETIC ENGINE OIL, SAE 5W-40

Material Code 663033002

SAE Grade 5W-40 Gravity, ASTM D4052, °API 34.0 Pounds Per Gallon 7.14 Flash Point, COC, ASTM D92, °F (°C) 450 (232) Viscosity, ASTM D445, cSt at 40°C 87

cSt at 100°C 14 Viscosity Index, ASTM D2270 166 CCS Vis, ASTM D5293, cP at °C 6,260 at -30°CMRV Vis, ASTM D4684, cP at °C 30,054 at -35°CMRV Yield Stress, ASTM D4684, Pa at °C <35Pour Point, ASTM D97, °F (°C) -44 (-42)TBN (Total Base No.), ASTM D2896 11 Color, ASTM D1500 L5.5

Mystik and JT-8 are registered trademarks of CITGO Petroleum Corporation. All other registered trademarks or trademarks are the property of their respective owners.


(Continued)


M20073

Engine Oils

66



M Y S T I K ® J T - 8 ® S Y N T H E T I C B L E N D S U P E R H E A V Y D U T Y E N G I N E O I L S M O N O G R A D E S

M 2 0 0 9 7

Mystik JT-8 Synthetic Blend Super Heavy Duty Engine Oils are recommended for hydraulic systems, transmissions and engines that recommend a Monograde engine oil type lubricant. Mystik JT-8 Synthetic Blend Super Heavy Duty Engine Oils are formulated with premium base oils and additives to reduce wear and extend component life.

• Recommended for Service Category CF (obsolete)• Recommended for Service Category CF-2 (obsolete)• Hydraulic systems where engine oils are recommended

TYPICAL PROPERTIES:

MYSTIK® JT-8® SYNTHETIC BLEND SUPER HEAVY DUTY ENGINE OILS MONOGRADES

Material Code 663000 663006 663007 663008

SAE Grade 10W 30 40 50 Gravity, ASTM D4052, °API 32.4 30.0 29.2 27.8 Density, lbs/gal 7.19 7.30 7.33 7.40 Specifc Gravity at 60F 0.863 0.876 0.880 0.888 Flash Point, ASTM D92 (COC), °F (°C) 439 489 486 482 Viscosity, ASTM D445, cSt at 40°C 39 93.1 121 206

cSt at 100°C 6.6 11.7 13.9 19.5 Viscosity Index, ASTM D2270 123 116 113 107 CCS Viscosity, ASTM D5293, cP 3900 at -25C NR NR NR MRV Pumpability, ASTM D4684, cP 9180 at -30C NR NR NR MRV Yield Stress at -25°C, ASTM D4684 <35 at -30C NR NR NR Pour Point, ASTM D97, °F (°C) -38 (-39) -33 (-36) -33 (-36) -22 (-30) Color, ASTM D1500 L3.0 L2.5 L2.5 L3.5 Sulfated Ash, ASTM D874, m% 0.92 0.92 0.92 0.92

NR = Requirement

DESCRIPTION:

D a t e 0 6 / 1 8

APPLICATIONS:



M20097

Engi

ne O

ils

77



M 2 0 1 0 6

Mystik JT-8 Synthetic Blend Super Heavy Duty Engine Oils are performance engineered with proprietary additive technology. Designed to ensure long lasting engine durability under the toughest operating conditions. Meets the performance demands of newer engine hardware.

Mystik JT-8 Synthetic Blend Super Heavy Duty Engine Oils are recommended for commercial over-the-road fleets, agriculture, construction equipment, buses, automobiles, and other similar diesel-powered applications where a premium quality engine oil is required.

• Engineered to provide long engine life in challenging service conditions

• Double the oil durability protection compared to conventional CJ-4 engine oils. Always follow OEM recommendations when extending oil drain intervals

• Maintains viscosity over extended service intervals, even under extreme operating conditions

• Recommended for low emission Tier 4 and on-highway low emission engines

• SAE 10W-30 improves fuel economy up to 3% compared to conventional 15W-40 viscosity grade oils

DESCRIPTION:

(Continued)

PERFORMANCECAPABILITIES:

D a t e 0 6 / 1 8

M Y S T I K ® J T - 8 ® S Y N T H E T I C B L E N D S U P E R H E A V Y D U T Y E N G I N E O I L S

Notes: • Consult owner's manual for proper SAE viscosity grade and API Service Category.

• Optimum drain intervals can be achieved utilizing oil analysis in conjunction with OEM guidelines.

SAE VISCOSITY GRADE 10W-30 15W-40

RECOMMENDED FOR:

CK-4 ✔ ✔

CJ-4 ✔ ✔

CI-4 PLUS ✔ ✔

CI-4 ✔ ✔

CH-4 ✔ ✔

SN — ✔

Caterpillar ECF-3 ✔ ✔

Cummins CES 20086 ✔ ✔

Detroit Diesel 93K222 ✔ ✔

Volvo/Mack/Renault/VDS-4.5/EOS-4.5/RLD-4 ✔ ✔

Paccar ✔ ✔

Navistar - International ✔ ✔

Ford WSS-M2C171-F1 ✔ ✔


(Continued)

M20106

Engine Oils

88



D a t e 0 6 / 1 8 - ( C o n t i n u e d )

M 2 0 1 0 6

TYPICAL PROPERTIES:

MYSTIK® JT-8® SYNTHETIC BLEND SUPER HEAVY DUTY ENGINE OILS

Material Code 625775002 625776002

SAE Grade 10W-30 15W-40 Gravity, ASTM D4052, °API at 60°F 31.5 30.8 Pounds/Gallon at 60°F 7.25 7.30 Specific Gravity at 60°F 0.87 0.88Viscosity at 40°C, cSt 79 112

100°C, cSt 11.9 15.2Viscosity Index 143 141 CCS Viscosity, cP, @ Temperature 5,830 @ -25°C 4370 @ -20°CMRV Viscosity, cP, @ Temperature 20,000 @ -30°C 15,620 @ -25°CMRV Yield Stress, Pa, @ Temperature <35 <35Pour Point, °F (°C) -38 (-39) -33 (-36)Flash Point, COC, °F (°C) 432 (222) 450 (232)Noack Evaporative, ASTM D5800, % Loss 11.6 10.7 Color, ASTM D1500 L3.0 L3.5Total Base Number, ASTM D2896 10 10Sulfated Ash, ASTM D874, % wt 1.0 1.0______ Mystik and JT-8 are registered trademarks of CITGO Petroleum Corporation. All other registered trademarks or trademarks are the property of their respective owners.

Values shown are typical values only and do not constitute a specification. The information contained herein is subject to change without notice.

CategoryMystik® JT-8

API CJ-4Mystik® JT-8

API CK-4

Back serviceable YES YES

Viscosity grades 15W-40/10W-30 15W-40/10W-30

Fleet million mile engine test rating Better Best

100% improved oxidation stability NO YES

Greater shear stability vs. conventional API CJ-4 YES YES

Aeration control vs. conventional API CJ-4 Better Best

SAE 10W-30 sustains improved fuel economy through 50,000 miles

Better Best

Compatible with conventional API CJ-4 oils YES YES

Best Overall Performance and Backward compatibility Better Best

API Comparison Chart


(Continued)


M20106

Engi

ne O

ils

99



M Y S T I K ® J T - 8 ® S Y N T H E T I C B L E N D S U P E R H E A V Y D U T Y E N G I N E O I L S S A E 1 0 W - 4 0 A N D S A E 1 5 W - 5 0

M 2 0 0 9 6

Mystik JT-8 Synthetic Blend Super Heavy Duty Engine Oil SAE 10W-40 provides an improvement in cold weather start up lubrication while providing excellent wear protection at higher operating temperatures.

Mystik JT-8 Synthetic Blend Super Heavy Duty Engine Oil SAE 15W-50 is designed for the equipment owner operating with older equipment with higher hours or miles that can benefit from a higher viscosity grade heavy duty engine oil.

Both SAE grades are engineered to provide excellent protection for equipment operating in severe conditions and will provide extended diesel engine life.

Mystik JT-8 Synthetic Blend Super Heavy Duty Engine Oils SAE 10W-40 and SAE 15W-50 are recommended for commercial over-the-road fleets, construction equipment, buses and other similar diesel-powered applications where premium quality engine is required.

TYPICAL PROPERTIES:

MYSTIK® JT-8® SYNTHETIC BLEND SUPER HEAVY DUTY ENGINE OILS SAE 10W-40 AND SAE 15W-50

Material Code 663002 663004

SAE Grade 10W-40 15W-50 API Service Category CK-4 CI-4 Plus Gravity, ASTM D 4052, °API 31.5 30.3 Density, lbs/gal 7.23 7.28 Flash Point, ASTM D 92 (COC), °F (°C) 442 (228) 440 (227) Viscosity, ASTM D 445, cSt at 40°C 105 151

cSt at 100°C 15.6 19.5 Viscosity Index, ASTM D 2270 157 148 CCS Viscosity, ASTM D 5293, cP 5700 at -25C 5300 at -20C MRV Pumpability, ASTM D 4684, cP 39,000 at -30C 23,100 at -25C MRV Yield Stress at -25°C, ASTM D 4684 <35 at -30C <35 at -25C Pour Point, ASTM D 97, °F (°C) -49 (-45) 49 (-45) Color, ASTM D 1500 L3.5 L4.0 Sulfated Ash, ASTM D 874, m% 1.0 1.0

DESCRIPTION:

D a t e 0 5 / 1 8



M20096

Small Engine Oils

10



M Y S T I K ® J T - 4 ® 2 - C Y C L EL A W N A N D G A R D E N E N G I N E O I L

M 2 0 0 8 4

Mystik JT-4 2-Cycle Lawn and Garden Engine Oil is a premium performance synthetic blend lubricant designed for use in high performance air-cooled 2-cycle generators, chain saws, lawn mowers, snow blowers, leaf blowers, and trimmers.

Mystik JT-4 2-Cycle Lawn and Garden Engine Oil is engineered for lower smoke and advanced protection for air cooled 2-cycle engines. This synthetic blend formula meets or exceeds the rigorous requirements of the API TC, JASO FD, FC and ISO-L-EGD classifications for 2-cycle air-cooled engine oils and also exceeds the performance requirements for JASO FC, JASO FB; ISO-L-EGC and -EGB. This advanced oil helps to protects today’s high RPM air cooled 2-cycle engines against exhaust port blocking, combustion chamber and piston deposits, ring sticking and scuffing, and wear. The JASO FD Certification number for this lubricant is 001 MYS 091.

Mystik JT-4 2-Cycle Lawn and Garden Engine Oil is formulated with premium base oils and a new low ash additive package that provides excellent lubricity and detergency performance which surpasses the standard for preventing piston and combustion chamber deposits. In addition, Mystik JT-4 2-Cycle Lawn and Garden Engine Oil is a synthetic blend which reduces exhaust smoke and prevents piston seizure and cylinder scuffing. Mystik JT-4 2-Cycle Lawn and Garden Engine Oil mixes readily with fuel for pre-mix type, even at low temperatures.

Mystik JT-4 2-Cycle Lawn and Garden Engine Oil is recommended for use in air-cooled, 2-cycle applications where an API TC, JASO FD, FC or ISO-L-EGD product is preferred. It can be used in either premix or oil injection systems up to 50:1 fuel to oil ratios. Do not use in engines requiring an NMMA TC-W3, TC-WII, or TC-W product. Consult owner’s manual for fluid specifications.

Mystik JT-4 2-Cycle Lawn and Garden Engine Oil can be used in 2-cycle powered generators, chain saws, lawn mowers, snow blowers, leaf blowers, and trimmers operating in hot, dirty, dusty environments and high loads for extended periods. Mystik JT-4 2-Cycle Lawn and Garden Engine Oil provides the necessary protection to keep your air-cooled 2-cycle engine running cleaner, longer and with less smoke.

DESCRIPTION:

QUALITIES:

APPLICATIONS:

TYPICAL PROPERTIES:

MYSTIK® JT-4® 2-CYCLE LAWN AND GARDEN ENGINE OIL


Gravity, ASTM D4052, °API 32.0Density, lb/gal, at 60°F 7.21Flash Point, PMCC, ASTM D93, °F (°C) 185 (85)Flash Point, COC, ASTM D92, °F (°C) 203 (95)Viscosity, ASTM D445, cSt at 40°C 55 cSt at 100°C 8.5 ASTM D2161, SUS at 100°F 281 SUS at 210°F 54.8Viscosity Index, ASTM D2270 129Pour Point, ASTM D97, °F (°C) -49 (-45)Appearance, Color PurpleSulfated Ash, ASTM D874, % 0.13Total Base Number, ASTM D2896, mg KOH/g 2.2

D a t e 0 6 / 1 8



M20084

Small Engine Oils

10

Smal

l Eng

ine

Oils

11



M Y S T I K ® J T - 4 ® 2 - C Y C L E P R E M I U M O U T B O A R D E N G I N E O I L

M 2 0 0 8 7

Mystik JT-4 2-Cycle Premium Outboard Engine Oil is an ashless lubricant guaranteed to protect 2-cycle marine engines and marine OEM warranties.

• Designed for premix type outboard engines.

• Helps reduce piston ring sticking and scuffing.

• Readily mixes with gasoline.

Mystik JT-4 2-Cycle Premium Outboard Engine Oil is recommended for water-cooled or liquid-cooled 2-cycle engines requiring an NMMA TC-W3, TC-WII® or TC-W® type oil. It may also be used in many air-cooled 2-cycle engine applications requiring TC-W3 or API Service Category TC. Recommended for pre-mix systems. Consult owner’s manual for fluid specifications.

Mystik JT-4 2-Cycle Premium Outboard Engine Oil will provide protection for gasoline fueled 2-cycle engines when used at the primary dilution recommended by the original equipment manufacturer.

DO NOT USE IN 4-CYCLE ENGINES!

DESCRIPTION:

BENEFITS:

APPLICATIONS:

MYSTIK® JT-4® 2-CYCLE PREMIUM OUTBOARD ENGINE OIL


Gravity, ASTM D4052, °API 31.5Density, lb/gal at 60°F 7.23Flash Point, PMCC, ASTM D93, °F (°C) 178 (81)1

Flash Point, COC, ASTM D92, °F (°C) 197 (92)Viscosity, ASTM D445 cSt at 40°C 32 cSt at 100°C 5.9Viscosity, ASTM D2161 SUS at 100°F 163 SUS at 210°F 46Viscosity Index, ASTM D2270 130Pour Point, ASTM D97, °F (°C) -28 (-39)Appearance, Color Blue/GreenSulfated Ash, ASTM D874, % <0.004Total Base Number, ASTM D2896, mg KOH/g 8.6 NOTE(1) DOT Combustible Liquid

TYPICAL PROPERTIES:

D a t e 0 6 / 1 8



M20087

Small Engine Oils

12



M Y S T I K ® J T - 4 ® 2 - C Y C L E P R E M I U M P L U S O U T B O A R D E N G I N E O I L

M 2 0 0 8 8

Mystik JT-4 2-Cycle Premium Plus Outboard Engine Oil, a synthetic blend, provides superb protection for high performance, high horsepower, 2-cycle outboard marine engines. It effectively combats wear, scuffing and deposit problems. It provides high-temperature oxidation resistance, corrosion protection, superior engine cleanliness, enhanced lubricity for longer engine life and is guaranteed to protect marine OEM warranties.

• Significantly reduces carbon or deposit build-up on engine parts and piston ring sticking.

• For direct injection or pre-mix; mixes readily at low temperatures

• High film strength for improved lubricity which provides:

– Increased engine efficiency

– Excellent scuffing and wear protection

– Cleaner, better-running engines producing less smoke.

Mystik JT-4 2-Cycle Premium Plus Outboard Engine Oil is recommended for all water-cooled or liquid-cooled 2-cycle engines requiring NMMA TC-W3®, TC-WII® or TC-W® type oil. It may also be used in many air-cooled 2-cycle engine applications requiring TC-W3 or API Service Category TC. Recommended for both direct injected and pre-mix systems. Consult owner’s manual for fluid specification.

Mystik JT-4 2-Cycle Premium Plus Outboard Engine Oil will provide outstanding protection for gasoline fueled 2-cycle engines when used at the primary dilution recommended by the original equipment manufacturer.


DESCRIPTION:

QUALITIES:

APPLICATIONS:

MYSTIK® JT-4® 2-CYCLE PREMIUM PLUS OUTBOARD ENGINE OIL


Gravity, ASTM D287, °API 31.8 Density lbs/gal at 60°F 7.215Flash Point, PMCC, ASTM D93, °F (°C) 144 (62)1

Flash Point, COC, ASTM D92, °F (°C) 185 (85)Viscosity, ASTM D445 cSt @ 40°C 31 cSt @ 100°C 6.0Viscosity, ASTM D2161 SUS at 100°F 159 SUS at 210°F 47Viscosity Index, ASTM D2270 145Pour Point, ASTM D97, °F (°C) -54 (-48)Appearance, Color GreenSulfated Ash, ASTM D874, % 0.04Total Base Number, ASTM D2896, mg KOH/g 9.7 NOTE(1) DOT Combustible Liquid

TYPICAL PROPERTIES:

D a t e 0 6 / 1 8



M20088

Smal

l Eng

ine

Oils

13



M Y S T I K ® J T - 4 ® A L L - I N - O N E O U T B O A R D E N G I N E O I L

M 2 0 0 9 9

Mystik JT-4 ALL-IN-ONE Outboard Engine Oil is a unique ultra-premium, licensed NMMA TC-W3® 2-cycle oil with a fuel stabilizer, ethanol treatment and engine cleaner that guarantees to protect marine engines through their OEM warranty period and beyond.

• Contains fuel stabilizer• Contains ethanol fuel treatment• Contains powerful detergents to remove existing carbon deposits from engine parts.• Ashless chemistry Mystik JT-4 ALL-IN-ONE Outboard Engine Oil can be used in multiple 2-cycle enginesrequiring TC-W3 and API TC engine oils including:

• Marine – outboard engines, personal watercraft (PWC)• Recreation equipment – ATVs, snowmobiles, motorcycles, dirt bikes• Other power equipment: chain saws, chippers/shredders, log splitters, snow blowers, generators• Lawn and garden: push mowers, lawn tractors, leaf blowers/vacuums, edgers, trimmers, tillers

This superior product helps prevent the adverse effects that ethanol fuel can have on marine engines. It cleans up deposits left from other 2-cycle products and can be used with new engines to ensure trouble free operation, to maintain engines at the start or end of a season and to help bring old engines back to life. Mystik JT-4 ALL-IN-ONE Outboard Engine Oil provides outstanding protection for gasoline fueled 2-cycle engines when used at the primary dilution recommended by the original equipment manufacturer.

DESCRIPTION:

FEATURES:

APPLICATIONS:

TYPICAL PROPERTIES:

MYSTIK® JT-4® ALL-IN-ONE OUTBOARD ENGINE OIL


Gravity, ASTM D287, °API 26.2 Density lbs/gal at 60°F 7.47Flash Point, PMCC, ASTM D93, °F (°C) 176 (80)1

Pour Point, ASTM D97, °F (°C) –60 (–51)Viscosity, ASTM D445, cSt at 40°C 62 cSt at 100°C 9.8 ASTM D2161, SUS at 100°F 317 ASTM D 2161, SUS at 210°F 59.5Viscosity Index, ASTM D2270 143Sulfated Ash, ASTM D874, m% 0.001Color Purple

NOTE:(1) DOT Combustible Liquid

D a t e 0 6 / 1 8



M20099

Small Engine Oils

14



M Y S T I K ® J T - 4 ® S E A & S N O W ®

2 - C Y C L E E N G I N E O I L

M 2 0 0 8 9

Mystik JT-4 Sea & Snow 2-Cycle Engine Oil is a synthetic blend, low smoke oil designed for use in high performance air- or liquid-cooled two-stroke engines of Personal Water Craft (PWC) and Snowmobiles.

Mystik JT-4 Sea & Snow 2-Cycle Engine Oil is engineered for lower smoke and advanced protection for air-cooled 2-cycle engines. The synthetic blend formula meets or exceeds the rigorous requirements of the API TC, JASO FD and ISO-L-EGD classifications for 2-cycle air-cooled engine oils and also exceeds the performance requirements for JASO FC, JASO FB; ISO-L-EGC and -EGB. This advanced oil helps protect today’s high performance air-cooled 2-cycle engines against exhaust port blocking, combustion chamber and piston deposits, ring sticking and scuffing, and wear. The JASO FD Certification number for this lubricant is 001 MYS 075.Mystik JT-4 Sea & Snow is formulated with premium base oils and a new synthetic low ash additive package that provides excellent lubricity and detergency performance that surpasses standards for preventing piston and combustion chamber deposits. In addition, Mystik JT-4 Sea & Snow is a synthetic blend which reduces exhaust smoke and prevents piston seizure and cylinder scuffing. Mystik JT-4 Sea & Snow mixes readily with fuel for pre-mix type, even at low temperatures.

Mystik JT-4 Sea & Snow 2-Cycle Engine Oil is recommended for use in air-cooled, 2-cycle applications where an API TC, JASO FD or ISO-L-EGD product is preferred. It can be used in either premix or oil injection systems up to 50:1 fuel ratios. It may also be used in certain motorcycle engines which are liquid cooled. Not recommended for engines requiring an NMMA TC-W3®, TC-WII®, or TC-W® product. Consult owner’s manual for fluid specifications.Mystik JT-4 Sea & Snow is formulated primarily for use in snowmobiles and personal watercraft. It can be used in 2-cycle motorcycles, generators, lawnmowers, and hand held power equipment such as leaf blowers, trimmers, and chainsaws. Mystik JT-4 Sea & Snow provides the necessary protection to keep your snowmobile or PWC running cleaner, longer, and with less smoke.DO NOT USE IN 4-CYCLE ENGINES!

DESCRIPTION:

QUALITIES:

APPLICATIONS:

TYPICAL PROPERTIES:

MYSTIK® JT-4® SEA & SNOW® 2-CYCLE ENGINE OIL


Gravity, ASTM D4052, °API 32.0Density, lb/gal at 60°F 7.21Flash Point, PMCC, ASTM D93, °F (°C) 185 (85) COC, ASTM D92, °F (°C) 203 (95)Viscosity, ASTM D445, cSt at 40°C 55 cSt at 100°C 8.5 ASTM D2161, SUS at 100°F 281 SUS at 210°F 54.8Viscosity Index, ASTM D2270 129Pour Point, ASTM D97, °F (°C) -49 (-45)Appearance, Color PurpleSulfated Ash, ASTM D874, % 0.1Total Base Number, ASTM D2896, mg KOH/g 2.2

D a t e 0 6 / 1 8

Mystik, JT-4 and Sea & Snow are registered trademarks of CITGO Petroleum Corporation. All other registered trademarks or trademarks are the property of their respective owners.


M20089

Smal

l Eng

ine

Oils

15



M Y S T I K ® J T - 4 ® S Y N T H E T I C 2 - C Y C L E P E R S O N A L W A T E R C R A F T E N G I N E O I L

M 2 0 0 7 7

Mystik JT-4 Synthetic 2-Cycle Personal Watercraft Engine Oil utilizes premium synthetic base oils combined with a special synthetic additive system to provide superior high temperature oxidation stability and wear protection. Its unique tri-blend of synthetic components provides ideal high temperature performance and quick starts in all temperatures. This balance of synthetic components enhances fuel economy, and improves high temperature thermal and oxidation stability.

The special additive system designed for specific use in Personal Watercraft engines provides the best protection against engine wear, rust and corrosion, and ensures engine cleanliness. The advanced formula used in Mystik JT-4 Synthetic 2-Cycle Personal Watercraft Engine Oil far exceeds Personal Watercraft engine requirements for an API TC and JASO FC quality oil.

• Provides superior protection in high temperatures

• Permits quick-fill lubrication flow during start-up to help reduce wear

• Promotes longer engine life through increased wear, rust and corrosion protection

• Improves equipment productivity and reliability

For use in all air-cooled or liquid-cooled 2-cycle (Injector or Premix) Personal Watercraft engines including those manufactured by Sea Doo, Kawasaki, Polaris, Yamaha, and other original equipment manufacturers. Mystik JT-4 Synthetic 2-Cycle Personal Watercraft Engine Oil is ideal for engines operating in high temperatures and where performance demands the most from your oil. Consult owners manual for fluid specifications.

Mystik JT-4 Synthetic 2-Cycle Personal Watercraft Engine Oil is recommended for use in 2-cycle Personal Watercraft engine applications requiring API TC and JASO FC quality oil.

DO NOT USE IN OUTBOARD MARINE ENGINES!

DESCRIPTION:

FEATURES:

RECOMMENDED:

APPLICATIONS:

MYSTIK® JT-4® SYNTHETIC 2-CYCLE PERSONAL WATERCRAFT ENGINE OIL


Gravity, ASTM D287, °API 32.9 Density lbs/gal 7.17Flash Point, PMCC, ASTM D93, °F (°C) 194 (90)Flash Point, ASTM D92, COC, °F (°C) 230 (110)Pour Point, ASTM D97, °F (°C) –54 (–48)Viscosity, ASTM D445 cSt @ 40°C 54 cSt @ 100°C 9.2Viscosity Index, ASTM D2270 152Visual Color PurpleSulfated Ash, ASTM D874, m% 0.015TBN, ASTM D2896, mg KOH/g 4.3

TYPICAL PROPERTIES:

D a t e 0 6 / 1 8



M20077

Small Engine Oils

16



M Y S T I K ® J T - 4 ® S Y N T H E T I C 2 - C Y C L ES N O W M O B I L E E N G I N E O I L

M 2 0 0 7 5

Mystik JT-4 Synthetic 2-Cycle Snowmobile Engine Oil utilizes premium synthetic base oils combined with a special synthetic additive system to provide superior cold temperature protection and quick starts in extreme cold. Its unique tri-blend of synthetic components provides ideal low temperature performance and quick starts in extreme cold. This balance of synthetic components enhances fuel economy, improves cold temperature performance and high temperature thermal stability.

The special additive system is designed for specific use in Snowmobile engines. It provides the best protection against engine wear, rust and corrosion, and ensures engine cleanliness. The advanced formula used in Mystik JT-4 Synthetic 2-Cycle Snowmobile Engine Oil meets Snowmobile engine requirements for an API TC and JASO FC quality oil.

• Provides superior protection in temperature extremes

• Permits quick-fill lubrication flow during cold weather start-up to help reduce wear



• Cleans power valves for improved performance

For use in all air-cooled or liquid-cooled 2-cycle (Injector or Premix) Snowmobile engines including those manufactured by Arctic Cat, Ski Doo, Polaris, Yamaha, and other original equipment manufacturers. Mystik JT-4 Synthetic 2-Cycle Snowmobile Engine Oil is ideal for engines operating in extreme cold temperatures and where performance demands the most from your oil. Consult owner’s manual for proper fluid specification.

Mystik JT-4 Synthetic 2-Cycle Snowmobile Engine Oil is recommended for use in 2-cycle Snowmobile engine applications requiring API TC and JASO FC quality oil.

DO NOT USE IN OUTBOARD MARINE ENGINES!

DESCRIPTION:

FEATURES:

RECOMMENDED:

APPLICATIONS:

TYPICAL PROPERTIES:

MYSTIK® JT-4® SYNTHETIC 2-CYCLE SNOWMOBILE ENGINE OIL


Gravity, ASTM D287, °API 32.9 Density lbs/gal 7.17Flash Point, PMCC, ASTM D93, °F (°C) 194 (90)Flash Point, ASTM D92, COC, °F (°C) 230 (110)Pour Point, ASTM D97, °F (°C) –54 (–48)Viscosity, ASTM D445 cSt @ 40°C 54 cSt @ 100°C 9.2Viscosity Index, ASTM D2270 152Visual Color PurpleSulfated Ash, ASTM D874, m% 0.015TBN, ASTM D2896, mg KOH/g 4.3

D a t e 0 6 / 1 8



M20075

Smal

l Eng

ine

Oils

17



M Y S T I K ® J T - 4 ® 4 - C Y C L E M A R I N E E N G I N E O I L S

M 2 0 0 9 5

Mystik JT-4 4-Cycle Marine Engine Oils are specially formulated, proven and certified for use in 4-cycle marine inboard, outboard and personal watercraft engines. The carefully crafted formulations are designed to provide maximum protection under the most demanding marine conditions.

• Formulated to meet the warranty requirements of Mercury, Yamaha, Evinrude and other leading OEM’s

• Provides superior rust and corrosion protection in high-performance marine engines under the harshest of marine environments

• Outstanding scuff and wear protection

• Ensures maximum engine cleanliness

• Formulated to meet the demanding requirements of 4-cycle marine engines requiring NMMA FC-W® oils

• Full Synthetic and Synthetic Blend formulations

• Multiple viscosity grades for comprehensive category coverage

For use in 4-cycle marine inboard, outboard and personal watercraft engines. Recommended in applications requiring NMMA FC-W. Meets warranty requirements of Mercury, Yamaha, Evinrude and other leading OEM’s. Mystik JT-4 4-Cycle 10W-40 provides excellent protection for personal watercraft as well, and meets warranty requirements of Honda, Kawasaki, Polaris, Sea Doo and other original equipment.

NOT FOR USE IN 2-CYCLE OR DIESEL ENGINES. Consult owner’s manual for proper lubricant selection.

DESCRIPTION:

FEATURES:

APPLICATIONS:

D a t e 0 6 / 1 8

TYPICAL PROPERTIES:

MYSTIK® JT-4® 4-CYCLE MARINE ENGINE OILS

Material Code 663094002 663093002 663095002 663097002

SAE Grade 10W-30 10W-40 25W-40 25W-50 Full Synthetic Full Synthetic Syn Blend Syn Blend

Gravity, ASTM D287, °API 32.0 31.9 28.3 28.0Density, lbs/gal 7.21 7.21 7.37 7.39Flash Point, ASTM D92, COC °F (°C) 437 (225) 453 (234) 455 (235) 500 (260)Pour Point, ASTM D97, °F (°C) -27 (-33) -22 (-30) -6 (-21) -17 (-27)Viscosity, ASTM D445, cSt at 40°C 80.5 98.4 149 195

cSt at 100°C 12.4 14.9 15.9 19.1Viscosity Index, ASTM D2270 151 158 114 112CCS Viscosity, cP at -25°C , ASTM D5293 5900 5660 — — cP at -10°C , ASTM D5293 — — 6100 8200NOACK Volatility, ATM D5800, % Loss 7.2 9 4.5 4.0Color, ASTM D1500 2.5 2.5 4.0 3.5Sulfated Ash, ASTM D874, m% 1.1 1.1 1.1 1.1TBN, ASTM D2896, mg KOH/g 9.3 9.2 9.0 8.7



M20095

Small Engine Oils

18



M Y S T I K ® J T - 4 ® S Y N T H E T I C 4 - C Y C L E S N O W M O B I L E M O T O R O I L S A E 0 W - 4 0

M 2 0 0 7 6

Mystik JT-4 Synthetic 4-Cycle Snowmobile Motor Oil SAE 0W-40 utilizes premium synthetic base oils combined with a special synthetic additive system to provide superior cold temperature protection and quick starts in extreme cold. The synthetic components provide optimum low temperature performance while minimizing volatility. This balance of synthetic components enhances fuel economy, improves cold temperature performance and high temperature thermal stability.

The special additive system is designed for specific use in Snowmobile engines. It provides the best protection against engine wear, rust and corrosion, and ensures engine cleanliness. The advanced formula used in Mystik JT-4 Synthetic 4-Cycle Snowmobile Motor Oil SAE 0W-40 far exceeds Snowmobile engine requirements for an API SL, JASO MA and NMMA FC-W quality oil.

• Provides superior protection in cold temperatures

• Permits quick-fill lubrication flow during cold weather start-up



For use in 4-cycle Snowmobiles including those manufactures by Arctic Cat, Polaris, Ski-Doo, Yamaha, and other original equipment manufacturers. Mystik JT-4 Synthetic 4-Cycle Snowmobile Motor Oil SAE 0W-40 is ideal for engines operating in extreme cold weather and where performance demands the most from your oil. Consult owner’s manual for proper lubricant selection.

Mystik JT-4 Synthetic 4-Cycle Snowmobile Motor Oil SAE 0W-40 is recommended for use in Snowmobile engine applications requiring an API SL, JASO MA and NMMA FC-W quality oil.


DESCRIPTION:

FEATURES:

RECOMMENDED:

APPLICATIONS:

MYSTIK® JT-4® SYNTHETIC 4-CYCLE SNOWMOBILE MOTOR OIL, SAE 0W-40


Gravity, ASTM D287, °API 33.8 Density, lbs/gal 7.13Flash Point, ASTM D92, COC, °F (°C) 428 (220)Pour Point, ASTM D97, °F (°C) –56 (–51)Viscosity, ASTM D445 cSt @ 40°C 93 cSt @ 100°C 14.8Viscosity Index, ASTM D2270 166CCS Viscosity, cP (°C), ASTM D5293 6000 (–35)NOACK Volatility, ASTM D5800, % Loss 7Color, ASTM D1500 2.5Sulfated Ash, ASTM D874, m% 0.9TBN, ASTM D2896, mg KOH/g 9.5

TYPICAL PROPERTIES:

D a t e 0 6 / 1 8



M20076

Smal

l Eng

ine

Oils

19



M 2 0 0 8 0

Mystik JT-4 Synthetic 4-Cycle All-Terrain Vehicle Motor Oils utilize premium synthetic base oils combined with a special additive system to provide outstanding protection for high performance All-Terrain Vehicle (ATV) and Utility Vehicle (UTV) engines. These full synthetic formulas provide optimum high and low temperature performance while minimizing volatility. This balance of synthetic technologies enhance fuel economy, improve cold temperature performance, and high temperature thermal and oxidation stability.

The advanced additive systems are specifically designed for use in ATV and UTV engines. They provide superior protection against engine wear, rust and corrosion, and ensures engine cleanliness. Mystik JT-4 Synthetic 4-Cycle All-Terrain Vehicle Motor Oils, available in SAE 0W-40, SAE 10W-40 and SAE 10W-50 grades, provide extra protection for gasoline powered ATV and UTV engines requiring a JASO MA quality oil.

• Protect in extreme hot and cold temperatures• Permit lubrication flow during cold weather start-up• Promote longer engine life by reducing wear, rust and corrosion• Provide excellent thermal and oxidation stability• Improve equipment productivity and reliability

For use in 4-cycle gasoline powered ATV and UTV engines including those manufactured by Arctic Cat, Bombardier, Honda, Kawasaki, Polaris (including 1000 ProStar), Yamaha, and other original equipment manufacturers. Ideal for high performance engines operating in extreme low and high temperatures and where performance demands the most from your oil. Select the SAE 0W-40 grade, if frequent usage at low temperatures is expected. Consult your owner’s manual for proper lubricant selection.

Mystik JT-4 Synthetic All-Terrain Vehicle Motor Oils are recommended for use in 4-cycle gasoline powered ATV and UTV engine applications requiring a JASO MA quality oil. Designed to be used in wet clutch applications that require JASO MA quality oil.

DESCRIPTION:

FEATURES:

RECOMMENDED:

APPLICATIONS:

TYPICAL PROPERTIES:

M Y S T I K ® J T - 4 ® S Y N T H E T I C 4 - C Y C L E A L L - T E R R A I N V E H I C L E M O T O R O I L S

MYSTIK® JT-4® SYNTHETIC 4-CYCLE ALL-TERRAIN VEHICLE MOTOR OILS

Material Codes 663079002 663080002 663085002SAE Grade 0W-40 10W-40 10W-50Gravity, ASTM D287, °API 33.8 31.9 33.5 Density, lbs/gal 7.13 7.21 7.14Flash Point, ASTM D92, COC, °F (°C) 428 (220) 453 (234) 457 (236)Pour Point, ASTM D97, °F (°C) –56 (–51) –22 (–30) -39 (-39) Viscosity, ASTM D445 cSt @ 40°C 93 98.4 126.6 cSt @ 100°C 14.8 14.9 17.85Viscosity Index, ASTM D2270 166 158 157CCS Viscosity, cP (°C), ASTM D5293 6000 (–35) 5660 (–25) 6592 (-25)NOACK Volatility, ASTM D5800, % Loss 7.0 9.0 7.4Color, ASTM D1500 2.5 2.5 2.5Sulfated Ash, ASTM D874, m% 0.9 1.0 1.0TBN, ASTM D2896, mg KOH/g 9.5 9.2 8.05

D a t e 0 6 / 1 8




M20080

Small Engine Oils

20



M Y S T I K ® J T - 4 ® P R E M I U M H I G H P E R F O R M A N C E L O W E R U N I TG E A R L U B R I C A N T

M 2 0 0 8 5

Mystik JT-4 Premium High Performance Lower Unit Gear Lubricant is formulated specifically for the marine industry. It contains the latest generation of a proprietary EP additive system, designed to provide maximum protection against wear, rust, corrosion and deposits.

This improved gear lubricant, specifically designed for boating applications, offers top level protection, surpassing other marine gear lubricants using GL-4 and GL-5 80W-90 technology:

• Superior EP lubrication and corrosion protection in the presence of moisture (fresh and sea water).

• Improved gear protection for shock load conditions encountered with harsh startup engagement, power reversal, and propeller entanglement.

Recommended for use in all outboard and stern drive gear units specifying SAE 90, 80W-90 or 85W-90, including OMC Type “C.” Includes MerCruiser, OMC Cobra, Volvo stern drives and Mercury, Evinrude, Johnson, Mariner, Yamaha, Suzuki, and Force outboards.

DESCRIPTION:

QUALITIES:

APPLICATIONS:

TYPICAL PROPERTIES:

MYSTIK® JT-4® PREMIUM HIGH PERFORMANCE LOWER UNIT GEAR LUBRICANT

SAE GRADE 85W-90


Gravity, ASTM D4052, °API 26.3 Density, lb/gal at 60°F 7.5 Flash Point, ASTM D92, COC, °F (°C) 420 (216) Viscosity, cSt at 100°C 16.0 Brookfield Viscosity, -23°C, cP 102,000 Pour Point, ASTM D97, °F (°C) -15 (-26) Channel Point, °F (°C), Max -31 (-35) Color, Visual Blue Foam Test, ASTM D892 Pass Copper Corrosion, 3 hrs at 250°F Pass

D a t e 0 6 / 1 8



M20085

Auto

mot

ive

Gear

Oils

2121



M 2 0 0 9 4

This full synthetic gear lubricant provides energy efficiency benefits and excellent protection in HD service and over wide temperature ranges. It is designed with premium synthetic base lubricants and an extra performance additive system.

It provides extra Extreme Pressure (EP) protection to minimize wear and scuffing. It is used in service fill lubrication of limited slip axles. It has outstanding thermal stability for long service life and it keeps gears clean and seals effective.

Mystik JT-7 Extended Range Full Synthetic Gear Lubricant SAE 75W-140 saves energy by decreasing friction over an extreme range of operating conditions. It is shear stable and exceeds API Service MT-1 performance for use in non-synchronized manual transmissions used in buses and heavy-duty trucks.

• API Gear Service GL-5, GL-4 and MT-1. Also meets EP performance equivalent to former GL-6

• Service fill lubricant for “limited slip” axles

• Superior oxidation resistance for extended drain intervals. 500,000 mile capable with heavy-duty severe-service

• Engineered with synthetic base lubricants and advanced shear stable and thermally stable additive system to achieve energy efficiency and improve performance

• Excellent extreme pressure (EP), wear, and scuff protection to reduce wear even under the most severe service conditions

• Outstanding oxidation resistance and thermal stability to resist deposit formation better than conventional gear oils

• High viscosity index and low pour point to function over a wider temperature range than conventional gear oils

• Effective rust and foam inhibitors protect bearings and gears

• Provides extremely good cold weather flow properties and high temperature lubrication; stays in grade

• Superior lubrication in cold operating conditions due to low pour points and improved flow properties

• Compatible with conventional and synthetic oils and materials designed for use with either type

• Improved fuel economy in heavy duty applications because of reduced friction and minimal lubricant drag. Energy savings are also obtained in industrial applications.

• Mystik JT-7 Extended Range Full Synthetic Gear Lubricant SAE 75W-140 usually eliminates any need for a seasonal oil change. The reduced number of viscosity grades required minimizes the chance of misapplication and reduces inventory.

DESCRIPTION:

FEATURES:

(Continued)

M Y S T I K ® J T - 7 ® E X T E N D E D R A N G E F U L L S Y N T H E T I C G E A R L U B R I C A N T S A E 7 5 W - 1 4 0

Energy Efficiency Benefits and Better Protection Over a Wider Temperature RangeD a t e 0 6 / 1 8


M20094

21

Automotive Gear Oils

2222



M 2 0 0 9 4

D a t e 0 6 / 1 8 - ( C o n t i n u e d )

Mystik JT-7 Extended Range Full Synthetic SAE 75W-140

For HD transmissions, axles and other gear boxes where SAE 75W-140, 80W-140 or 85W-140 are specified along with API GL-5, GL-4, MT-1.

MYSTIK® JT-7® EXTENDED RANGE FULL SYNTHETIC GEAR LUBRICANT SAE 75W-140


SAE Grade 75W-140

Gravity, ASTM D4052, °API 31 Density, lb/gal at 60°F 7.2 Specific Gravity at 60°F 0.87 Viscosities: at -26°C, cP 16,500 at -40°C, cP 138,000 at 40°C, cSt 185 at 100°C, cSt 25.8 Viscosity Index 174 Flash Point, ASTM D92, COC, °F (°C) 370 (188) Pour Point, ASTM D97, °F (°C) -42 (-41) Color, ASTM D1500 2.0

TYPICAL PROPERTIES:

APPLICATIONS:

M Y S T I K ® J T - 7 ® E X T E N D E D R A N G E F U L L S Y N T H E T I C G E A R L U B R I C A N T S A E 7 5 W - 1 4 0



M20094

(Continued)

Auto

mot

ive

Gear

Oils

2323



M Y S T I K ® J T - 7 ® M U L T I - P U R P O S E G E A R L U B R I C A N T S

M 2 0 0 0 8

Mystik JT-7 Multi-Purpose Gear Lubricants are multi-purpose, thermally stable, sulfur-phosphorus extreme pressure (EP) gear lubricants that exceed the performance requirements of the latest axle and non-synchronized manual transmission. A specially balanced additive provides thermally stable gear lubricants with exceptional durability under high temperature conditions. These are thermally stable and thermally durable gear lubricants. Others lose their EP performance when subjected to thermal stress. Mystik JT-7 Multi-Purpose Gear Lubricants can take the heat and continue to provide superior EP protection, minimum gear wear, excellent deposit control and improved rust and corrosion protection under extreme service conditions. Recommended for all automotive and heavy duty axle service including break-in, add-to or make-up, drain and refill, and for “limited slip” axles. (80W-90)

• Top quality, versatile hypoid EP gear lubricants; recommended in applications that specify API Gear Service GL-4, GL-5 and MT-1 and SAE J2360.

• Superior service in differentials of passenger cars and trucks and heavy duty equipment

• Excellent in limited slip differentials known as Sure-grip®, Posi-trac®, Trac-lock®, etc., for complete fill or for top-off. (80W-90)

• Multiple viscosity grades with high viscosity index. Wide temperature range for all season application in most climates

• Have outstanding thermal stability/durability or long term heat resistance, better than most competitive conventional gear lubricants, thereby providing longer life at higher operating temperatures

• EP additive provides superior wear and scuff protection

MYSTIK® JT-7® MULTI-PURPOSE GEAR LUBRICANTS

Material Code 663705002 663706002

SAE Grade 80W-90 85W-140

AGMA Lubricant Number 4 EP 7 EP Gravity, ASTM D4052, °API 26.5 25.2 Density, lb/gal at 60°F 7.45 7.53 Specific Gravity at 60°F 0.895 0.90 Viscosities: at -12°C, cP – 55,000 at -26°C, cP 90,000 – at 40°C, cSt 146 347 at 100°C, cSt 16.2 28.0 at 100°F, cSt (SUS) 172 (797) 514 (2380) at 210°F, cSt (SUS) 17.4 (87.5) 33.6 (159) Viscosity Index 122 108 Flash Point, ASTM D92, COC, °F (°C) 403 (206) 438 (226) Pour Point, ASTM D97, °F (°C) -27 (-33) 0 (-18) Color Red Red

TYPICAL PROPERTIES:

DESCRIPTION:

FEATURES:

D a t e 0 7 / 1 8



M20008


2424



M 2 0 0 0 9

This synthetic blend gear lubricant provides energy efficiency benefits and excellent protection in HD service and over wide temperature ranges. It is designed with select synthetic base lubricants and a high performance additive system.

It provides Extreme Pressure (EP) protection to minimize wear and scuffing. It is used in service fill lubrication of limited slip axles. It has outstanding thermal stability for long service life and it keeps gears clean and seals effective.

Mystik JT-7 Synthetic Blend SAE 75W-90 Gear Lubricant saves energy by decreasing friction over an extreme range of operating conditions. It is shear stable and meets API Service MT-1 performance for use in non-synchronized manual transmissions used in buses and heavy-duty trucks

• API Gear Service GL-4 , GL-5 and MT-1

• Engineered with synthetic and highly refined conventional base oils and a thermally stable additive system to achieve energy efficiency and improve performance

• Excellent extreme pressure (EP) protection to reduce wear and scuffing even under the most severe service conditions

• Outstanding oxidation resistance and thermal stability to resist deposit formation better than conventional gear oils

• High viscosity index and low pour point to provide lubrication at extreme tempurature ranges

• Effective rust and foam inhibitors protect bearings and gears

• Shear stable viscosity modifier ensures viscosity stays in grade

• Compatible with conventional and synthetic oils and materials designed for use with either type oil

• Improved fuel economy in heavy duty applications because of reduced friction and minimal lubricant drag. Energy savings are also obtained in industrial applications.

• Mystik JT-7 Synthetic Blend SAE 75W-90 can eliminate the need for a seasonal oil change.

• Can be used in place of SAE 80W-90, reducing the number of vicosity grades required, minimizing inventory and the chance of misapplication

DESCRIPTION:

FEATURES:

(Continued)

M Y S T I K ® J T - 7 ® S Y N T H E T I C B L E N D S A E 7 5 W - 9 0 G E A R L U B R I C A N T

Energy Efficiency Benefits and Better Protection Over a Wider Temperature RangeD a t e 0 6 / 1 8


(Continued)

M20009

24

Auto

mot

ive

Gear

Oils

2525



M 2 0 0 0 9

D a t e 0 6 / 1 8 - ( C o n t i n u e d )

Mystik JT-7 Synthetic Blend SAE 75W-90

Recommended for use in HD transmissions, axles and other gear boxes where API GL-4, GL-5, and/or MT-1 are specified in viscosity grade SAE 75W-90 or 80W-90.

MYSTIK® JT-7® SYNTHETIC BLEND SAE 75W-90 GEAR LUBRICANT


SAE Grade 75W-90

Gravity, ASTM D4052, °API 30 Density, lb/gal at 60°F 7.3 Specific Gravity at 60°F 0.88 Viscosities: at -26°C, cP 16,500 at -40°C, cP 140,000 at 40°C, cSt 113 at 100°C, cSt 15.8 Viscosity Index 150 Flash Point, ASTM D92, COC, °F (°C) 417 (214) Pour Point, ASTM D97, °F (°C) -53 (-48) Color, ASTM D1500 1.5

TYPICAL PROPERTIES:

APPLICATIONS:

M Y S T I K ® J T - 7 ® S Y N T H E T I C B L E N D S A E 7 5 W - 9 0 G E A R L U B R I C A N T


(Continued)


M20009


2626



M Y S T I K ® S X - 7 0 0 0 ® S Y N T H E T I C F L U I D S

M 2 0 0 1 0

The Ultimate in Extended Gear Protection Approved for Eaton® Roadranger® and Rockwell Extended Warranties

Mystik SX-7000 Synthetic Fluids are heavy-duty, state-of-the-art premium synthetic lubricants accepted by the Eaton/Fuller Corporation and Rockwell for use in conjunction with their extended warranty programs. These lubricants will also provide exceptional service in Spicer/Dana transmissions and differentials. They meet API Service MT-1 performance requirements for use in non-synchronized manual transmissions used in buses and heavy-duty trucks. They exhibit superior performance at extreme temperatures and maximum component protection for the extended long haul. The high and low temperature performance and long-term thermal, oxidation and shear stability (resistance to viscosity loss in service) of these products is far superior to conventional transmission and drive axle lubricants. With up to 500,000 miles of useful life, these premium quality lubricants save the cost and inconvenience of frequent transmission and drive axle lube changes. That’s ten times longer service in transmissions (50,000 miles normal) and two and a half times longer service in drive axles (100,000 miles normal) than using conventional petroleum-based lubricants.

Today’s aerodynamic designs, increased loads, and tighter schedules and margins demand superior lubricant performance in terms of thermal stability and component protection with reduced maintenance and downtime. Better operating performance can also be realized in terms of more horsepower and improved fuel mileage as a result of the superior lubricating properties of Mystik SX-7000 Synthetic Fluids.

Product Name Description Use

SX-7000 50 Synthetic SAE 50 Non-EP Transmission SX-7000 75W-90 Synthetic SAE 75W-90 EP-Drive Axle/Transmission SX-7000 80W-140 Synthetic SAE 80W-140 EP Drive Axle

• Extended drain intervals

• All-climate, year-round performance

• Highly stable under conditions of severe heat, oxidation, and shear

• Superior low temperature performance

• Extremely low channel points

• Improved component protection

• Reduced component wear

• Longer drive axle and lubricant life

• Extended seal life

• Good foam control

• Excellent demulsibility

• Improved fuel economy and horsepower

DESCRIPTION:

FEATURES:

(Continued)

D a t e 0 6 / 1 8


(Continued)

M20010

Auto

mot

ive

Gear

Oils

2727



Mystik SX-7000 Synthetic Fluids 75W-90 and 80W-140 are heavy duty extreme pressure (EP) GL-5 synthetic gear lubricants specially formulated for extended drain and severe service in heavy duty drive axles. Fully synthetic base stocks with high viscosity indexes and low pour points are blended with an EP additive along with rust, oxidation, and corrosion inhibitors to provide superior performance and protection.

NOTE: Mystik SX-7000 50, 75W-90 and 80W-140 meet or exceed all applicable performance requirements for: API Gear Lubricant Classification GL-5 and MT-1. API MT-1 denotes lubricants intended for non-synchronized manual transmissions used in buses and heavy-duty trucks.

Mystik SX-7000 Synthetic Fluid SAE 50 is recommended for heavy-duty service in manual transmission for which the manufacturer recommends this SAE viscosity grade. It is formulated with specific antiwear, rust, oxidation, foam and corrosion inhibitors to protect bearings and synchronizers and to promote longer transmission life. As in the other products in this series, Mystik SX-7000 Synthetic Fluid SAE 50 provides improved start-up, easier shifting and less gear wear in low temperature environments. Less friction, less drag and improved oxidation resistance combine to provide fuel economy benefits and longer drain intervals.

– SAE J2360 – Dana SHAES 429 – Eaton Roadranger E500 — SHAES 256 Rev. A (80W-140), Rev. C (75W-90) – Arvin Meritor O-76N, O-76E (75W-90) – Mercedes Benz MB Approval 235.8 – Mack GO-J (80W-140)

MYSTIK® SX-7000® SYNTHETIC FLUIDS

Material Code 663515002 (MTF) 663750002 663751002

SAE Viscosity Grade (J306-8) 50 75W-90 80W-140AGMA Grade (ASTM D2422) – 4 EP 5-6 EP Gravity, ASTM D4052, °API 33.1 33.5 32.0 Specific Gravity at 60°F 0.86 0.91 0.92 Density, lb/gal at 60°F 7.16 7.15 7.25 Viscosities: at -26°C, cP – – 90,000 at -40°C, cP 50,000 125,000 – at 40°C, cSt. 132 120 310 at 100°C, cSt. 17.5 15.9 31.2 Viscosity Index 146 140 139 Pour Point, ASTM D97, °F (°C) -49 (-45) -48 (-54) -33 (-36) Channel Point, FTMS 3456, °F (°C) – -60 (-51) -55 (-48) Flash Point, ASTM D92, °F (°C) 430 (221) 400 (205) 410 (210) Foam Test, ASTM D892, Sequence I, II, III Pass Pass Pass Copper Strip Corrosion, ASTM D130 3 hrs. at 250°F Pass Pass Pass Thermal Stability Test Pass Pass Pass Demulsibility Test Pass Pass Pass Timken OK Load, ASTM D2782, lb – 50 85 Four-Ball EP Weld Point, ASTM D2783, kgf – – 400 Four-Ball Load Wear Index, ASTM D2783, kgf – – 63.8 Color 2.0 1.5 1.5

TYPICAL PROPERTIES:

D a t e 0 6 / 1 8 - ( C o n t i n u e d )

M 2 0 0 1 0

M Y S T I K ® S X - 7 0 0 0 ® S Y N T H E T I C F L U I D S

– Mack GO-J Plus (75W-90) – Scania STO 1:0 – International TMS-6816 – General Electric D 50E9C – Harnishfeger (P&H) 474 – ZF TE-ML 07A/08

Mystik and SX-7000 are registered trademarks protected by federal law. All other registered trademarks or trademarks are the property of their respective owners.

(Continued)


M20010


2828



M Y S T I K ® U N I V E R S A L G E A R L U B R I C A N T

M 2 0 0 1 2

For API Gear Lubricant Service: GL-4 Hypoid EP

Mystik Universal Gear Lubricant contains a Sulfur-Phosphorus (“SP” type) EP additive that provides antiwear and antiscuff lubricity. This product is recommended for gears subject to shock loading in service and for those gear set types requiring “EP” additive compounding because of their design characteristics. A Sulfur-Phosphorus (“SP” type) mild EP additive provides antiwear and antiscuff lubricity for gears subject to shock loading in service and those gear set types requiring “EP” additive compounding because of their design characteristics. • API Service Classification GL-4

• May be used for “add-to” in automotive axles requiring a Hypoid EP lube except those incorporating “limited slip” or “anti-spin” features

• Economically satisfies industrial applications where large loss due to leakage is a factor

MYSTIK® UNIVERSAL GEAR LUBRICANT


SAE Grade 90 AGMA Lubricant Number 4 EP Gravity ASTM D4052, °API 22.9 Density, lb/gal at 60°F 7.6 Specific Gravity at 60°F 0.917 Viscosities: at 40°C, cSt 237 at 100°C, cSt 16.5 at 100°F, cSt (SUS) 275 (1273) at 210°F, cSt (SUS) 17.1 (86.1) Viscosity Index 64 Flash Point, ASTM D92, COC, °F (°C) 430 (221) Pour Point, ASTM D97, °F (°C) -20 (-29) Color Dark Amber

TYPICAL PROPERTIES:

DESCRIPTION:

FEATURES:

D a t e 7 / 1 8

Mystik is a registered trademark of CITGO Petroleum Corporation. All other registered trademarks or trademarks are the property of their respective owners.


M20012

Tran

smis

sion

/Pow

er F

luid

s

29



Mystik JT-5 Synthetic Blend TFX tractor fluid is a performance engineered tractor fluid for the equipment owner needing longer component life and ensuring optimum efficiency for many years of tillage and harvesting operations.

• The investment in today’s farm tractors often requires longer ownership of 10 years or more while operating at lowest possible maintenance cost.

• Achieving maximum equipment productivity is required for survival with so many challenges facing modern farm profitability

• Mystik JT-5 Synthetic Blend TFX is recommended for leading tractor manufacturers such as John Deere, New Holland, Kubota and Case/IH MAT 3540 to provide the convenience of one product for improved inventory management for mixed farm fleets while achieving optimum performance.

• Mystik JT-5 Synthetic Blend TFX is designed for modern farm tractors that produce significantly more horsepower requiring greater protection for high production machines that impose much greater stress on transmissions, axles with multiple high output hydraulic applications.

M Y S T I K ® J T - 5 S Y N T H E T I C B L E N D T F X

M 2 0 1 0 7

DESCRIPTION:

FEATURES & PERFORMANCE

BENEFITS

D a t e 0 7 / 1 8

ADVANCED TECHNICAL FEATURES PERFORMANCE BENEFIT

Synthetic Blend ✓ Improves performance over wider temperature range and reduces tendency of fluid breakdown due to sustained high operating temperatures

Shear stable viscosity with a high viscosity index

✓ Maintains and sustains optimum viscosity over the service intervals to ensure overall productivity and efficiency

✓ Promotes longer component life of heavily loaded components

✓ Suitable for CVT transmissions that require a stable viscosity through temperature changes and for the life of the oil.

Non-Zinc anti-wear formulation ✓ Provides improved water tolerance that maintains efficiency throughout transmission, hydraulics and brake system

✓ Zinc free formula also reduces impact on environment

Leak resistant-seal maintainer technology

✓ Conditions seals to prevent leakage as equipment ages with higher hours of operation

Special friction modifiers ✓ Improves brake system function and protects against brake chatter

Clean system-detergent/dispersant ✓ Helps minimize tendency for transmission clutch plate glazing from high temperature, deposit build up, protecting against loss of friction control and power transfer efficiency to the drive train.

✓ Maintains high pressure hydraulic system efficiency by preventing hydraulic valve deposit build up and sluggish operation.

Double acting anti-rust/anti-foam technology

✓ Prevents system corrosion and controls tendency for air entrainment resulting in efficient power transfer.

Wide temperature range ✓ Excellent fluidity and start up lubrication that improves system response time in colder temperature operation

Anti-slip formulation ✓ Ensures power transfer efficiency under high loads in transmissions, axles and all hydraulic components


M20107

29

(Continued)

Transmission/Pow

er Fluids

30




APPLICATIONS:

D a t e 0 7 / 1 8

MYSTIK® JT-5 SYNTHETIC BLEND TFX


API Gravity, ASTM D4052, °API 31.0Density, lb/gal 7.3Specific Gravity 0.88Viscosities:

at -20°C, cP 3493at -35°C, cP 38200at 40°C, cSt 58.81at 100°C, cSt 9.56

Viscosity Index 146KRL Sheared Viscosity (20hr.) CEC L-45-A-99, cSt 8.2

(Tapered Roller Bearing Shear Test)Tractor FZG ASTM D4998

Weight loss 19mg (Max is 50mg) Flash Point, COC, ASTM D92, °F (°C) 457 (236)Pour Point, ASTM D97, °F (°C) -43 (-45)Water Tolerance (Separation with 5% water) 0.0 4-Ball EP Wear, ASTM D4172, mm 0.36Color Light Amber

TYPICAL PROPERTIES:


M 2 0 1 0 7

RECOMMNED FOR THE FOLLOWING APPLICATIONS• AGCO Power Fluid 821XL• Allison C-4• CASE MS 1205, 1206, 1207, 1209, 1210• CAT TO-2• Denison HF-0, HF-1, HF-2• Eaton Hydraulics• Ford New Holland ESN-M2C134-D• Kubota UDT, Super UDT• API GL-4• Case New Holland: MAT 3540, MAT 3525, MAT 3505• John Deere J20C• Massey Ferguson M-1145• White Q-1826• Volo WB101 • ZF TE-ML-03E, TE-ML-05F, TE-ML-17E, TE-ML-21F

For use in the following OEM equipment: • AGCO • CASE IH • Deutz • Ford • John Deere • Komatsu • Kubota • Massey Ferguson • New Holland •White, and others.


M20107

(Continued)

Tran

smis

sion

/Pow

er F

luid

s

31



M Y S T I K ® J T - 5 ® T R A C T O R T R A N S - H Y D R A U L I C F L U I D

M 2 0 0 1 4

Mystik JT-5 Tractor Trans-Hydraulic Fluid provides excellent performance in modern agricultural equipment. It offers outstanding gear wear protection, brake chatter control and oxidation resistance. Particularly well suited for hard working applications where an added level of protection is desired. Excellent filterability characteristics along with rust and corrosion inhibitors, water tolerance and wide temperature range performance.

• Contains special “friction modifiers” for superior brake chatter control

• Formulated to resist leakage

• Formulated with advanced detergent/dispersant, antiwear, antioxidant, antirust and antifoam additives

• Has proven field performance

Recommended for use in equipment where the following fluids are specified:

• AGCO Power Fluid 821XL

• Allison C-4• CASE MS 1205, 1206, 1207, 1209, 1210

• CAT TO-2

• Denison HF-0, HF-1, HF-2

• Eaton Hydraulics

• Ford New Holland ESN-M2C134-D

• Kubota UDT

• API GL-4

• Case New Holland: MAT 3525

• John Deere J20C

• Massey Ferguson M-1145

• White Q-1826

Suitable for use in the following equipment:

• AGCO

• CASE IH

• KH Deutz

• Ford

• John Deere

• Komatsu

• Kubota

• Massey Ferguson

• New Holland

• Volvo WB101

• White, and others

DESCRIPTION:

FEATURES:

(Continued)

D a t e 0 6 / 1 8

APPLICATIONS:


M20014

Transmission/Pow

er Fluids

32



M 2 0 0 1 4

D a t e 0 6 / 1 8 - ( C o n t i n u e d )


MYSTIK JT-5 TRACTOR TRANS-HYDRAULIC FLUID

Material Code 663509002 API Gravity, ASTM D4052, °API 31.0 Density, lb/gal 7.3 Specific Gravity 0.88 Viscosities: at -35°C, cP 48,200 at 40°C, cSt 60.3 at 100°C, cSt 9.3 Viscosity Index 130 Flash Point, COC, ASTM D92, °F (°C) 457 (236) Pour Point, ASTM D97, °F (°C) -40 (-40) Falex, ASTM D3233-A, lbs 1,350 4-Ball EP Wear, ASTM D4172, mm 0.38 Color Light Amber

TYPICAL PROPERTIES:



M20014

32

(Continued)

Tran

smis

sion

/Pow

er F

luid

s

33



M 2 0 0 2 3

Mystik Multi-Purpose ATF is a multi-function, automatic transmission fluid manufactured from selected high-quality base stocks and premium additives. It protects transmission parts against rust, corrosion, and wear. It is dyed red for leak detection and is engineered to give superior protection and performance. Mystik Multi-Purpose ATF is recommended where the following lubricants are specified: General Motors transmissions calling for DEXRON®-III, DEXRON-IIE and DEXRON-II fluids; Ford transmissions calling for MERCON® type ATF’s; Allison Transmission Division (C-4).

• A single fluid for a wide variety of power transmission uses: automotive automatic transmissions, industrial torque converters, sensitive hydraulic fluid applications, power-shift transmissions, Allison automatic transmissions and power steering fluids.

• Excellent stability for long life service• Anti-wear, anti-leak, anti-foam treated• Detergent inhibitor provides gum-up resistance• Can be used industrially as an excellent multi-viscosity, “all weather” hydraulic fluid, torque converter

fluid and as a cold temperature gear lubricant • Meets the performance requirements of the following hydraulic fluid, power-shift transmission fluid

and automatic transmission fluid specifications:

Vickers M-2950-S and I-286-S GM DEXRON® IIIG/H, IID/E Caterpillar TO-2 Ford MERCON® Allison Type C-3 and C-4 Ford ESP-M2C166H

Recommended for use in automatic transmissions manufactured by General Motors and Ford for model years 2006 and prior (except those calling for FORD Type “F” Fluid, MERCON SP, MERCON V, DEXRON-VI and CVT fluids). Suitable for use in foreign cars and trucks requiring the use of DEXRON-III, DEXRON-IIE, DEXRON-II fluids, and MERCON type ATF’s. Consult owner’s manual for fluid specification.

M Y S T I K ® M U L T I - P U R P O S E A T F

TYPICAL PROPERTIES:

MYSTIK® MULTI˜PURPOSE ATF

Material Code 633135002 Gravity, ASTM D4052, °API 33.0Pounds Per Gallon 7.16Flash Point, ASTM D92, COC, °F (°C) 424 (218) Pour Pont, ASTM D97, °F (°C) -54 (-48)Viscosity, ASTM D445, cSt at 40°C 34.3 cSt at 100°C 6.95 ASTM D2983, cP at -20°C 1,020 cP at -40°C 15,100Vicosity Index, ASTM D2270 169Color Red

DESCRIPTION:

FEATURES:

APPLICATIONS:

D a t e 0 6 / 1 8

Mystik is a registered trademark protected by federal law. All other registered trademarks or trademarks are the property of their respective owners.


M20023

Transmission/Pow

er Fluids

34



M 2 0 0 8 1

Mystik Synthetic Blend Multi-Vehicle ATF contains the highest quality synthetic and mineral oil base stocks combined with a state-of-the-art additive system to provide superior performance in automatic and powershift transmissions. It is suitable for use in transmissions calling for Ford MERCON® V, Ford MERCON (obsolete), General Motors DEXRON®-IIIH (obsolete), and Allison C-4 type fluids.

• Superior oxidation and thermal stability• Outstanding anti-wear performance for protection of transmission hardware• Excellent cold temperature flow properties• Compatible with a wide range of seal materials to prevent transmission leaks• Can be used in most vehicles• Provides inventory optimization (multi-vehicle compatible) without the use of ATF supplements

Mystik Synthetic Blend Multi-Vehicle ATF is suitable for use in GM, Ford, Toyota, Honda, Nissan, Hyundai and other imported vehicles where the following applications are recommended:

• Ford MERCON and MERCON V* (Not recommended for use in California)• GM DEXRON-II and DEXRON-III• Allison C-4• BMW LT-71141, ETL-7045E, 2634, 8072B.• Nissan/Infiniti Nissan ATF, Matic D, Matic J, and Matic K• Mitsubishi Diamond SP-II and SP-III• Hyundai/KIA SP-II and SP-III• Toyota/Lexus Type T, T-III and T-IV• Honda/Acura ATF-Z1 (except in CVTs)• Mercedes Benz 236.3; .5; .6; .7; .9; .10; and .11; ATF 3403 M-115• Volvo Standard 1273,41 (Transmission oil 97341); 1161521; 1161540 / 1161640 – JWS 3309 • Volkswagen/Audi G052025 (A2); G052055; G052162 (A1, A2); G052990 (A2); G055025 (A2); GUS000162• ZF TE-ML 11A; 11B• JASO 1A• MAN 339A• Mazda Type T-IV• Subaru ATF-HP• Renault Matic D2

*Please note that California law prohibits manufacturers of multi-vehicle ATF from recommending products in certain applications where the viscometrics do not match those of official OEM specifications. CITGO therefore does not recommend the use of Mystik® Synthetic BlendMulti-Vehicle ATF in these applications in California.

Do not use Mystik Synthetic Blend Multi-Vehicle ATF in vehicles calling for Type F, DEXRON VI, MERCON SP, MERCON LV, Toyota/Lexus WS, and CVT’s. Consult owner’s manual for properfluid specification.

DESCRIPTION:

FEATURES:

APPLICATIONS:

(Continued)

M Y S T I K ® S Y N T H E T I C B L E N D M U L T I - V E H I C L E A T F

D a t e 0 6 / 1 8


M20081

Tran

smis

sion

/Pow

er F

luid

s

35



M 2 0 0 8 1

D a t e 0 6 / 1 8 - ( C o n t i n u e d )

TYPICAL PROPERTIES:

MYSTIK® SYNTHETIC BLEND MULTI˜VEHICLE ATF


Viscosity, cSt at 40°C 35Viscosity, cSt at 100°C 7.2Viscosity Index 178Specific Gravity @ 60 °F 0.851Pour Point, ASTM D97, °F (°C) -60 (-51)Brookfield Viscosity @ -40 °C, cP 9600Appearance Red

M Y S T I K ® S Y N T H E T I C B L E N D M U L T I - V E H I C L E A T F



M20081

(Continued)

Transmission/Pow

er Fluids

36



M Y S T I K ® L U B R I C A N T ST E N A X ® F L U I D S

M 2 0 0 1 7

Meets The Requirements of Caterpillar TO-4 And Allison C-4

Manufacturers of heavy duty equipment are continually upgrading their machines and components. Significant improvements in transmissions and final drives have increased equipment durability and productivity, but have also increased the workload on gears and bearings, and required the development of new and diverse friction materials. The use of the correct lubricant to support these new designs is critical.

Mystik Lubricants Tenax Fluids are heavy duty transmission and final drive lubricants formulated to meet the performance requirements of Caterpillar TO-4 (10W, 30, & 50) and Allison C-4 (10W & 30). They provide the protective qualities essential to maximize equipment life and performance.

• Meets the performance requirements of Caterpillar TO-4

• The SAE 10 and SAE 30 meet the Allison C-4 specification

• Recommended for use in heavy duty powershift transmissions, final drives, hydrostatic transmissions, torque converters and hydraulics where a TO-4 or C-4 fluid is recommended. These products are not recommended as engine lubricants.

• SAE 50 can be used in Eaton/Fuller, Rockwell and Dana/Spicer transmissions for service-fill

• Excellent performance in ZF powershift transmissions used in off-road machines, special vehicles and lift trucks

MYSTIK® LUBRICANTS TENAX® FLUIDS

Material Code 663510002 663511002 663512002

SAE Grade 10W 30 50

Gravity, ASTM D4052, °API 31.1 31.0 27.3Density, lb/gal 7.3 7.4 7.4Specific Gravity 0.877 0.886 0.896Viscosity: at -35°C, cP 23,000 - - at 40°C, cSt 38.1 96 209.4 at 100°C, cSt 6.1 11.3 17.9Viscosity Index 112 104 100Flash Point, ASTM D92, COC, °F (°C) 420 (216) 446 (230) 511 (266)Pour Point, ASTM D97, °F (°C) -38 (-39) -27 (-33) 0 (-18)Color, ASTM D1500 L3.0 3.5 4.0

TYPICAL PROPERTIES:

DESCRIPTION:

FEATURES:

APPLICATIONS:

D a t e 0 6 / 1 8



M20017

Tran

smis

sion

/Pow

er F

luid

s

37



Mystik Twin Disc Fluid is a very low viscosity, low friction fluid with antifoam inhibitor and is for specialized applications. Certain Twin Disc Clutch company converters do not use this type fluid. May also be used as an ISO 2 Spindle Oil.

MYSTIK® TWIN DISC FLUID


Viscosity Grade: SAE Grade Thinner than SAE 5W ISO Grade (Approx.) 2

Gravity, ASTM D4052, °API 43.0 Density, lb/gal 6.75 Specific Gravity 0.811 Viscosities: at 40°C, cSt 2.5 at 100°F, cSt (SUS) 2.67 (34.3) Flash Point, ASTM D92, °F (°C) 187 (86) Fire Point, ASTM D92, °F (°C) 198 (92) Pour Point, ASTM D97, °F (°C) -40 (-40) Distillation, IBP 378 Aniline Point, ASTM D611, °F (°C) 180 (82) Carbon Residue, Weight % 0.01 Color Red

TYPICAL PROPERTIES:

For 3-Stage Torque Converters made by the Twin Disc Clutch Company Approved List S364C

NOTE: Certain Twin Disc Company converters do not use this type fluid. Make certain the unit involved requires a fluid listed on Twin Disc Approved List Sheet “S364C.”

M Y S T I K ® T W I N D I S C F L U I D

M 2 0 0 2 2

DESCRIPTION:

D a t e 0 6 / 1 8



M20022

38

Greases



Mystik Centra-Lube Grease is designed as an anti-leak industrial semi-fluid gear grease for industrial gearboxes and automatic, centralized lube systems where harder consistency greases are not pumpable in cold weather. It is ideal for leaky gearboxes and applications that are difficult to service. This premium quality product contains extreme pressure, antiwear, antirust, and antioxidant additives.

• Self leveling• Excellent wear protection and load carrying capability• Outstanding water resistance, protects against corrosion• Recommended for centralized lubrication systems and grease filled gear boxes

• As an industrial semi-fluid grease• Underground mine pressure gear systems and conveyor drive gearboxes• An “antileak” EP gear lubricant• For centralized lube systems where harder consistency greases are not pumpable in cold weather

Consult owner’s manual for proper lubricant selection.

NSF H2 (125249)

MYSTIK® CENTRA-LUBE™ GREASE

Material Code 665023002 NLGI Grade 0 to 00 Thickener Type Lithium 12-Hydroxystearate Texture Smooth, Adhesive Color Amber Worked Penetration, ASTM D217 380-410 Rust Prevention, ASTM D1743, rating Pass Copper Corrosion, ASTM D4048, rating 1b Oxidation, ASTM D942, psi loss @ 100 hrs 2.5 Timken OK Load, ASTM D2509, lb. 60 Approximate Temperature Range, °F (°C) 0 to 250 (-18 to 121)Base Oil: Viscosity @ 40°C, cSt 360

TYPICAL PROPERTIES:

M 2 0 0 2 4

M Y S T I K ® C E N T R A - L U B E T M G R E A S E

DESCRIPTION:

FEATURES:

APPLICATIONS:

APPROVALS:

CLASSIFICATION:

D a t e 0 5 / 1 8

Nonfood CompoundsProgram Listed H2

Registration No. 125249




M20024

38

Greases

39

Grea

ses



Mystik General Purpose Grease is a multi-purpose grease especially suited for normal temperature/speed conditions and non-critical service applications. This product is recommended for applications requiring frequent re-greasing due to a contaminating environment. • Water Resistant

• Economical


M 2 0 0 3 4

M Y S T I K ® G E N E R A L P U R P O S E G R E A S E

MYSTIK® GENERAL PURPOSE GREASE

Material Code 665150002 NLGI Consistency Number 2 Thickener Type Lithium Stearate Texture Smooth, Medium Fiber Color Dark Brown Worked Penetration, ASTM D217 265-295 Dropping Point, ASTM D566, °F (°C) 320 (160) Approximate Application Temperature Range, °F (°C) 0 to 265 (-18 to 129)

TYPICAL PROPERTIES:

DESCRIPTION:

FEATURES:

D a t e 0 5 / 1 8




M20034

40

Greases



M Y S T I K ® J T - 6 ® H I G H P E R F O R M A N C E M A R I N E G R E A S E

M 2 0 0 8 6

Mystik JT-6 High Performance Marine Grease is a smooth but tacky blue grease with outstanding water resistance. It is designed to provide excellent lubrication for greased chassis points and other wet-environment applications.

Mystik JT-6 High Performance Marine Grease combines an anhydrous calcium thickener system, special polymer and a proprietary additive system to ensure superior performance against rusting in both fresh and sea water marine applications.

• Premium high performance extreme pressure marine grease

• Outstanding water washout resistance, protects against saltwater corrosion

• Excellent wear protection and load carrying capability

• Polymer fortified for excellent metal adhesion

Recommended for marine applications including greased automotive chassis points, trailer wheel bearings, bearing buddies, boat lifts, hydraulic jack plates, steering components, tilt and trim systems, etc. Lubricates well over a wide temperature range – 0 to 250°F. It is not recommended for disc brake wheel bearings. Mystik JT-6 High Performance Marine Grease is also an excellent choice in non-marine applications where a general multi-purpose EP grease with an outstanding water and corrosion resistance is desired – water pumps, fifth wheels and other equipment operating in wet conditions.


DESCRIPTION:

QUALITIES:

APPLICATIONS:

TYPICAL PROPERTIES:

MYSTIK® JT-6® HIGH PERFORMANCE MARINE GREASE

NLGI Grade 2


Thickener Type Anhydrous CalciumTexture Smooth, AdhesiveColor, Observed BlueWorked Penetration, ASTM D217 265-295Approximate Temperature Range, °F (°C) 0 to 250 (-18 to 121)Dropping Point, ASTM D566, °F (°C) 290 (143)Water Washout, ASTM D1264, % loss @ 100°F 0.9Oil Separation, ASTM D1742, % loss <1 Rust Prevention, ASTM D1743, rating PassCopper Corrosion, ASTM D4048, rating 1bSynthetic Sea Water Corrosion, ASTM D5969, rating PassTimken OK Load, ASTM D2509, lb 55Four-Ball Weld, ASTM D2596, kgf 250Four-Ball Wear, ASTM D2266, mm 0.6 Base Oil Viscosity: 40°C, cSt 1080

D a t e 0 5 / 1 8




M20086

41

Grea

ses



NLGI Certified GC-LB

These high temperature Lithium Complex greases combine excellent multi-purpose properties with a high dropping point to give them application over a wide temperature range. Mystik JT-6 Hi-Temp greases exhibit a high Timken OK Load in addition to providing excellent Four-Ball Wear and EP performance. They provide superior protection to lubricate a wide variety of automotive, agricultural, trucking, mining, construction, and industrial equipment. They provide outstanding shock load protection. JT-6 Hi-Temp No. 2 is an extremely versatile performer that is highly recommended for disc brake wheel bearings and is specifically approved for use in Rockwell and Spicer universal joints. This grease provides excellent protection for heavily loaded industrial, mining, and construction applications. JT-6 Hi-Temp No. 1 was developed for applications where service conditions dictate a grease of softer consistency. Both meet the highest performance categories of ASTM D4950 Automotive Grease Classification System, GC for wheel bearing service and LB for chassis service.

• Mystik JT-6 Hi-Temp Greases provide excellent protection in severe service requirements such as disc brake wheel bearings, backhoe hinge pins, and conveyor bearings

• Mining operations, sand/gravel plants, and construction equipment where shock loads are placed on bearings benefit from the use of Mystik JT-6 Hi-Temp Greases


Dana CorporationSpicer Universal/Joint DivisionM-2006-J (#2)Registered NLGI GC-LBWeatherford Artificial Lift (#2)NSF H2 (125250)

M 2 0 0 2 6

(Continued)

M Y S T I K ® J T - 6 ® H I - T E M P G R E A S E S

DESCRIPTION:

APPLICATIONS:

APPROVALS:

CLASSIFICATION:

D a t e 0 7 / 1 8




M20026

42

Greases



MYSTIK® JT-6® HI-TEMP GREASES

Material Code 665003002 665005002 NLGI Consistency Number 1 2 NLGI Certified, ASTM D4950 GC-LB GC-LB Thickener Type Lithium Complex Lithium Complex Texture Smooth, Adhesive Smooth, Adhesive Color Red Red Worked Penetration, ASTM D217 310-340 265-295 Dropping Point, ASTM D2265, °F (°C) 500 (260) 550 (288) Water Washout, ASTM D1264, % loss @ 175°F 9.4 2.5 Rust Prevention, ASTM D1743, rating Pass Pass Copper Corrosion, ASTM D4048, rating 1b 1b Oil Separation, ASTM D1742, % loss 2 1 Timken OK Load, ASTM D2509, lb. 70 80 Four-Ball Wear, ASTM D2266, mm 0.45 0.45 Four-Ball Weld, ASTM D2596, kgf 315 315 Four-Ball Load Wear Index, ASTM D2596, kgf 50 50 Approximate Temperature Range, °F (°C) -10 to 325 -10 to 325 (-23 to 163) (-23 to 163) Base Oil Viscosity: 40°C, cSt 630 630

TYPICAL PROPERTIES:

D a t e 0 7 / 1 8 - ( C o n t i n u e d )

M 2 0 0 2 6





M20026

(Continued)

43

Grea

ses



Mystik JT-6 Hi-Temp Grease with Moly is a high performance mining and construction grease that provides superior performance where a moly-compounded, adhesive, multi-purpose high temperature lithium complex grease is required. This product gives optimum protection in severe environments.

• An exceptionally versatile premium quality multi-purpose lithium complex grease• Fully additive treated. EP/antiwear, rust and oxidation inhibited• Contains 3% Molybdenum Disulfide (moly) for extreme service conditions found in mining,

construction, and severe industrial applications• Water insoluble and water washout resistant• Superior wheel bearing and chassis performance• Superior protection to lubricate a wide variety of heavy duty automotive, agricultural, trucking,

industrial, mining, and construction equipment


MYSTIK® JT-6® HI-TEMP GREASE WITH MOLY


NLGI Consistency Number 2 Thickener Type Lithium Complex Texture Smooth, Adhesive Filler, % Molybdenum Disulfide 3% Color Gray/Black Worked Penetration, ASTM D217 265-295 Dropping Point, ASTM D2265, °F (°C) 500 (260) Min. Water Washout, ASTM D1264, % loss @ 175°F 2.5 Rust Prevention, ASTM D1743, rating Pass Copper Corrosion, ASTM D4048, rating 1b Oil Separation, ASTM D1742, % loss 1.0 Timken OK Load, ASTM D2509, lb. 60 Four-Ball Wear, ASTM D2266, mm 0.45 Four-Ball Weld, ASTM D2596, kgf 400 Approximate Application Temperature Range, °F (°C) -10 to 325 (-23 to 163) Base Oil Viscosity: 40°C, cSt 630

TYPICAL PROPERTIES:

M Y S T I K ® J T - 6 ® H I - T E M P G R E A S EW I T H M O L Y

M 2 0 0 3 1

DESCRIPTION:

FEATURES:

APPROVAL:

D a t e 0 5 / 1 8

AUTOMOTIVEWHEEL BEARING & CHASSIS

LUBRICANT

GC-LB




M20031

44

Greases



M Y S T I K ® J T - 6 ® S Y N T H E T I C H I - T E M P G R E A S E S

M 2 0 0 7 2

Mystik JT-6 Synthetic Hi-Temp Greases are high-temperature, full synthetic lithium complex greases that combine excellent multi-purpose properties with a high dropping point and low temperature pumpability that provides a wide operating temperature range. Mystik JT-6 Synthetic Hi-Temp Greases exhibit excellent wear control, EP performance and provide excellent water resistance critical in a variety of applications today. These products provide excellent corrosion protection in those applications with corrosive environments. Mystik JT-6 Synthetic Hi-Temp Greases provide superior protection in heavily loaded industrial, mining and construction applications as well as automotive service classification GC-LB with the ISO 220 #2.

• Premium quality lithium complex soap thickener

• Excellent corrosion protection, EP/AW

• Outstanding low temperature performance and pumpability

• Excellent water resistance

• Excellent high-temperature oxidation resistance

• Heavy Industrial

• Mining

• Steel Mills

• Construction

• Automotive Service (ISO 220 #2 Only)


DESCRIPTION:

FEATURES:

APPLICATIONS:

CLASSIFICATION:


LUBRICANT

GC-LB

(Continued)

D a t e 0 5 / 1 8


M20072

45

Grea

ses



MYSTIK® JT-6® SYNTHETIC HI-TEMP GREASES

Material Code 665071002 665072002 665077002

NLGI Consistency Number 1 2 2Texture Smooth Smooth SmoothColor, Observed Blue Blue BlueWorked Penetration, ASTM D217 310-340 265-295 265-295Dropping Point, ASTM D2265, °F (°C) 500 (260) 500 (260) 500 (260)Rust Prevention, ASTM D1743, rating Pass Pass PassEmcor Corrosion Protection Pass Pass Pass5% Synthetic Sea Water Corrosion Pass Pass PassWater Washout, ASTM D1264, % Loss 1.2 1.5 1.8 Oil Separation, ASTM D1742, g Loss — — 0.90Four-Ball Weld, ASTM D2596, kgf 500 500 500NLGI Classification — — GC-LB Base Oil Viscosity: 40°C, cSt 110 110 220

TYPICAL PROPERTIES:

D a t e 0 5 / 1 8 - ( C o n t i n u e d )

M 2 0 0 7 2

M Y S T I K ® J T - 6 ® S Y N T H E T I C H I - T E M P G R E A S E S




M20072

(Continued)

46

Greases



Mystik JT-6 Lo-Temp Extreme Grease is light colored, low staining, and water resistant. It provides antiwear protection under high loads. It is a low to medium temperature range multi-purpose grease for bearings. Mystik JT-6 Lo-Temp Extreme Grease performs well in extremely cold temperatures where minimum friction is necessary and where high speeds are involved. This product can also be used where excellent rust protection is required and where equipment is stored or used intermittently. It is considered by many to be the ultimate mining grease due to its ability to lubricate over a wide temperature range.

• Outstanding low temperature performance

• Excellent anti-wear and extreme pressure protection

• Water resistant - seals out water and protects against corrosion

• Recommended operating temperature range -40° to 250°F

• A low to medium temperature range multi-purpose grease for bearing and chassis applications

• For conditions where extremely cold temperatures prevail, minimum friction is necessary, high speeds are involved, excellent rust protection is required, or equipment is stored or used intermittently


M Y S T I K ® J T - 6 ® L O - T E M P E X T R E M E G R E A S E

M 2 0 0 2 8

DESCRIPTION:

FEATURES:

APPLICATIONS:

MYSTIK® JT-6® LO-TEMP EXTREME GREASE

Material Code 665027002 NLGI Consistency Number 2 Thickener Type Anhydrous Calcium Texture Smooth Color Medium Amber Worked Penetration, ASTM D217 265-295 Dropping Point, ASTM D566, °F (°C) 285 (140) Water Washout, ASTM D1264, % loss @ 175°F 5 Rust Prevention, ASTM D1743, rating Pass Oil Separation, ASTM D1742, % loss 5 Timken OK Load, ASTM D2509, lb 45 Four-Ball Wear, ASTM D2266, mm 0.56 Four-Ball Weld, ASTM D2596, kgf 315 US Steel Mobility @ 0°F, gpm 540 Low Temperature Torque, ASTM D4693, N-m 0.48 Approximate Temperature Range, °F (°C) -40° to 250° (-40° to 121°)Base Oil Viscosity: 40°C, cSt 20

TYPICAL PROPERTIES:

D a t e 0 5 / 1 8




M20028

47

Grea

ses



Mystik JT-6 Multi-Purpose Grease is an exceptionally water resistant product. It is light colored, low staining, and has a very low oil separation rate. Mystik JT-6 Multi-Purpose Grease provides excellent antiseize protection under high loads. Outstanding adhesion enables this product to stay in place better than most other greases. This product is a medium temperature range multi-purpose grease for extreme pressure loads and slow to medium speed bearings. It is excellent for greased chassis points, fifth wheels, and water pumps. It works especially well where extended lubrication intervals are practical, highly loaded or shock loaded grease lubricated applications exist, and excellent rust protection is desired. It is fully rust and oxidation inhibited.

Mystik JT-6 Multi-Purpose is also available in an aerosol form. This product penetrates hard-to-reach points to leave a protective coating of grease. Mystik JT-6 Multi-Purpose Spray Grease has the ability to stay in place and lubricate, even under extreme pressures and severe service. It resists rust, corrosion, oxidation, and wear. This product is ideal for hard to reach points and precise placement. Mystik JT-6 Multi-Purpose Spray Grease dries into a non-fluid consistency in about 15 minutes.

• Exceptionally water resistant - protects against corrosion

• Light colored and low staining

• Very low oil separation rate

• Provides anti-wear and extreme pressure protection

• Excellent adhesion permits it to have better “stay-ability” than most other greases

• A medium temperature range multi-purpose grease for extreme pressure loads, slow to medium speed bearings, greased chassis points, fifth wheels, and water pumps

• Especially good where extended lubrication intervals are practical, highly loaded or shock loaded grease lubricated applications exist, or where excellent rust protection is desired

• Aerosol is excellent for hard to reach locations

DANGER: Extremely flammable aerosol. Please refer to SDS for proper transport, storage and handling. Always check with local jurisdictions for warehouse requirements. Refer to equipment owner’s manual for proper lubricant recommendation.

NOTE: Because this product has better adhesion, it is a little more difficult to pump than less adhesive greases. Use of a follower plate is recommended where air driven pumps are used.

M 2 0 0 2 7

DESCRIPTION:

FEATURES:

APPLICATIONS:

M Y S T I K ® J T - 6 ® M U L T I - P U R P O S E G R E A S E

(Continued)

D a t e 0 5 / 1 8


M20027

48

Greases



MYSTIK® JT-6® MULTI-PURPOSE GREASE

AEROSOL (Grease)Material Code 665006002 665007002 NLGI Consistency Number 2 2 Thickener Type Anhydrous Calcium Anhydrous Calcium Texture Smooth, Adhesive Smooth, Adhesive Color Medium Amber Medium Amber Worked Penetration, ASTM D217 265-295 265-295 Dropping Point, ASTM D566, °F (°C) 290 (143) 290 (143) Water Washout, ASTM D1264, % loss at 100°F 0.9 0.9 Rust Prevention, ASTM D1743, rating Pass Pass Oil Separation, ASTM D1742, % loss < 1 < 1 Timken OK Load, ASTM D2509, lb. 55 55 Four-Ball Wear, ASTM D2266, mm 0.6 0.6 Four-Ball EP Weld Point, ASTM D2596, kgf 250 250 Four-Ball Last Non-Seizure Load, ASTM D2596, kgf 65 65 Approximate Application Temperature Range, °F (°C) 0 to 250 (-18 to 121) 0 to 250 (-18 to 121)Base Oil Viscosity: 40°C, cSt 1080 —

TYPICAL PROPERTIES:

D a t e 0 5 / 1 8 - ( C o n t i n u e d )

M 2 0 0 2 7





M20027

(Continued)

49

Grea

ses



M Y S T I K ® J T - 6 ® S U P E R H E A V Y D U T Y 4 6 0 G R E A S E

M 2 0 0 9 8

Mystik JT-6 Super Heavy Duty 460 Grease is an extended service capable, extreme pressure (EP) lubricating grease designed for a wide variety of heavy duty industrial, on highway and off highway equipment applications, especially pins, bushings and anti-friction bearings. Provides extra wear protection when operating with higher loads resulting in longer equipment component life. It is highly recommended for heavily loaded plain and anti-friction bearings such as those found in steel, paper, and cement industries.

Mystik JT-6 Super Heavy Duty 460 Grease is lithium complex thickened grease formulated with a premium additive system and a combination of synthetic and conventional base oils. The optimized formula provides superior performance properties over a wide operating temperature range.

• Proprietary adhesive, stay-in-place formula helps seal out contaminants and extend lubrication intervals

• High load-carrying capacity offers wear protection even under severely loaded conditions• Enhanced water and corrosion resistance protects equipment under adverse conditions including

saltwater spray and exposure to corrosive anti-icing agents• Wide operating range of –5° to 350°F for a variety of weather conditions and application

temperatures

Mystik JT-6 Super Heavy Duty 460 offers superior protection in a variety of applications where enhanced load carrying capability, water resistance, and anti-corrosion protection properties are required such as:

• Heavy Duty and Extreme Heavy Haul Trucking – 5th wheels, U-joints, kingpins, steering drag links, shackle pins, pivots and cross shaft spring pins

• Mining and Construction - bulldozers, scrapers, backhoes, excavators, compactors, cranes, paving machinery, articulated vehicles, soil compactors, graders, ditch hoes, loaders

• Pit and Quarry Equipment – rock crushers, conveyors, rock drills, bridge cranes, water tender, log trucks, chip van trucks

• Agriculture – tractors, implements, tillage, planting and seeding machinery, sprayers and spreaders, hay balers, harvesting machinery, combines, mowers, skid steers

• Heavy Industry – heavily loaded plain and anti-friction bearings in cement, paper, metal (steel, aluminum, copper) industries

• Forestry and Logging – harvester-processor, feller-buncher, mulcher-masticator, brush cutter, shovel logger, skidder, brush piling shovel, brush rake, yarder, log landing machines, shovel, stroke delimber, loader, grinder, chipper, debarker, forest road machines

Mystik JT-6 Super Heavy Duty 460 helps increase equipment life through superior performance including higher load capacity, capable of carrying up to 3X more load than conventional greases. Consult owner’s manual for proper lubricant selection.

DESCRIPTION:

FEATURES:

APPLICATIONS:

(Continued)

D a t e 0 5 / 1 8

3X Performance

Mystik JT-6 Super Heavy Duty

Conventional Grease

0 100 200 300 400 500 600 700 800 900

Four Ball Weld kgfASTM D-2596


M20098

(Continued)

50

Greases




D a t e 0 5 / 1 8 - ( C o n t i n u e d )

M 2 0 0 9 8



MYSTIK® JT-6® SUPER HEAVY DUTY 460 GREASE

ISO Viscosity Grade 460


NLGI Consistency Number 2Thickener Type Lithium ComplexTexture SmoothColor, Observed MagentaWorked Penetration, ASTM D217 265-295Dropping Point, ASTM D2265 °F (°C) 500 (260)Rust Prevention, ASTM D1743, rating Pass5% Synthetic Sea Water Corrosion PassWater Washout, ASTM D1264, % Loss 2.3Water Spray Off, ASTM D4049, % Loss 9.4US Steel Mobility @ 0°F, gpm 38Four-Ball Weld, ASTM D2596, kgf 800Base Oil Viscosity: 40°C, cSt 460

TYPICAL PROPERTIES:




M20098

(Continued)

51

Grea

ses



Mystik JT-6 Synthetic Blend Grease is a premium quality, multi-purpose, high temperature, lithium complex EP grease with excellent low temperature properties. A unique blend of petroleum base oils and synthetic fluids gives this grease excellent resistance to oxidation at elevated temperatures and exceptionally low start-up resistance (torque) under extreme low temperature conditions.

Engineered to protect under severe operating conditions, Mystik JT-6 Synthetic Blend Grease contains EP/antiwear, rust, and oxidation inhibitor additives to provide superior protection for a wide range of applications and service conditions. Mystik JT-6 Synthetic Blend Grease is categorized as an excellent high/low temperature multi-purpose grease due to its ability to lubricate over a very broad temperature range in a wide variety of automotive, agricultural, industrial applications. It meets the highest performance categories of ASTM D 4950 Automotive Grease Classification System, GC for wheel bearing service and LB for chassis service.

• A premium quality, multi-purpose, high temperature, lithium complex EP grease with excellent low temperature properties

• Fully additive treated. EP/antiwear, rust and oxidation inhibited

• Excellent oxidation and corrosion resistance

• Superior antiwear protection

• Excellent oil bleed characteristics

• Exceptionally low start-up resistance (torque) under low temperature conditions

• A unique blend of petroleum base oils and synthetic fluids in an optimized formulation that provides excellent low temperature, high temperature, and seal compatibility performance

• Certified by the NLGI for ASTM Service Classification GC-LB (ASTM D 4950) for use as a dual-service grease for wheel bearing and chassis applications

• Engineered for the lubrication and surface corrosion protection of vehicles and equipment operated over the temperature range of -27 to 325°F (-33 to 163°C)

• Excellent for high speed bearing applications

• Superior protection to lubricate a wide variety of automotive, agricultural and industrial equipment

• Provides excellent performance in severe low temperature applications


M Y S T I K ® J T - 6 ® S Y N T H E T I C B L E N D G R E A S E

M 2 0 0 3 0

DESCRIPTION:

FEATURES:

APPLICATIONS:

CLASSIFICATION:


LUBRICANT

GC-LB

(Continued)

D a t e 0 5 / 1 8


M20030

52

Greases



MYSTIK® JT-6® SYNTHETIC BLEND GREASE

Material Code 665051002 NLGI Consistency Number 2 Thickener Type Lithium Complex Texture Smooth, Buttery Color, Observed Blue Worked Penetration, ASTM D217 265-295 Dropping Point, ASTM D2265, °F (°C) 500 (260) Water Washout, ASTM D1264, % loss at 100°F 1.4 Rust Prevention, ASTM D1743, rating Pass Copper Corrosion, ASTM D4048, rating 1a Timken OK Load, ASTM D2509, lb. 65 Four-Ball Wear, ASTM D2266, mm 0.45 Four-Ball Weld, ASTM D2596, kgf 315 NLGI Certified, ASTM D4950 GC-LB Base Oil Viscosity: 40°C, cSt 70

TYPICAL PROPERTIES:

D a t e 0 5 / 1 8 - ( C o n t i n u e d )

M 2 0 0 3 0

M Y S T I K ® J T - 6 ® S Y N T H E T I C B L E N D G R E A S E




M20030

(Continued)

53

Grea

ses



Mystik Moly Grease is a premium quality, multi-functional, extreme pressure, lithium complex grease that combines the high temperature function of the thickener with molybdenum disulfide (moly) and graphite to provide extended extreme pressure and high temperature performance. This product provides equivalent performance to many 3% moly greases for extreme conditions found in mining, construction, and severe industrial applications.

Mystik Moly Grease is recommended for all bearing and sliding applications including shock, high loading and pound applications. This grease covers a wide range of applications including those found in off-road construction (bucket pins, bucket loaders, backhoes, articulated trucks, etc.), heavy duty fleets (fifth wheels, king pins, slack adjusters, pins and bushings), mining equipment (above and below ground bucket loaders, etc.) and industrial bearings. Not recommended for high speed lightly loaded bearings such as those found in electric motors.


M 2 0 0 9 2

M Y S T I K ® M O L Y G R E A S E

DESCRIPTION:

FEATURES:

D a t e 0 5 / 1 8

MYSTIK® MOLY GREASE

Material Code 665706002 NLGI Consistency Number 2.5 Thickener Type Lithium Complex Texture Smooth, Adhesive Color Black Worked Penetration, ASTM D217 255-285 Dropping Point, ASTM D2265, °F (°C), min 500 (260) Molybdenum Disulfide, m% 1.5 Graphite, m% 1.5 Rust Prevention, ASTM D1743, rating Pass Copper Corrosion, D4048, rating 1b Oxidation Stability, ASTM D942, psi drop 3 Timken OK Load, ASTM D2509, lb 60 Four-Ball Weld, ASTM D2596, kgf 400 Four-Ball Wear, ASTM D2266, mm 0.54 Water Washout, ASTM D1264, % loss @ 175°F 2.5 USS Mobility, 20°F, gpm 138.6 USS Mobility, 0°F, gpm 64.2 Base Oil Viscosity: 40°C, cSt 210

TYPICAL PROPERTIES:




M20092

54

Greases



Mystik OG-5 Outside Gear Grease is a premium high-performance open-gear lubricant that provides exceptional protection of heavily loaded open-gears exposed to a wide range of operating conditions. It provides exceptional extreme pressure and anti-wear protection, with excellent water resistance, and operates over a wide range of operating temperatures. Tough film strength protects against wear in the contact zone which helps to provide longer life for protected parts and reduces maintenance associated from damaged surfaces.

• Unique formula meets the challenges of lubricating a wide range of exposed gears operating in extremely challenging environments

• Provides exceptional extreme pressure and anti-wear resistance

• Very adhesive and tacky grease that clings to metal surfaces providing stay-in-place performance, water resistance, and provides protection against corrosion

• Protects mating surfaces against damaging wear which helps to extend component life.

• Solvent Free

• Engineered to provide a wide operating temperature range

• Suitable for use in mills, shovels, draglines ring and pinion gears

• Other applications include marine, guide rails, fifth wheels, slideways, swing gears, conveyor equipment, winch trucks, track rollers, drive rollers, chains, flanges and many other types of open or outside gearing found in construction and plant machinery

• Can be applied by gun, brush, swab, pump, etc.

Consult owner’s manual for proper lubricant selection. Refer to SDS for special handling instructions.

WARNING: Avoid contact with eyes, skin and clothing. IF IN EYES: Rinse cautiously with water for several minutes.

NOTE: Not for rolling element bearings. May be difficult to apply where temperatures are below 32°F.

M 2 0 0 2 9

DESCRIPTION:

FEATURES:

APPLICATIONS:

M Y S T I K ® O G - 5 O U T S I D E G E A R G R E A S E

MYSTIK® OG-5 OUTSIDE GEAR GREASE


NLGI Consistency Number 1-1/2 Thickener Type Lithium Stearate Soap Texture Smooth, Stringy Fillers Moly Disulfide & Graphite Color Black/Dark Brown Worked Penetration, ASTM D217 285-315 Dropping Point, ASTM D566, °F (°C) 300 (149) Rust Prevention, ASTM D1743, rating Pass Timken OK Load, ASTM D2509, lb. 45 Four-Ball Load Wear Index, ASTM D2596 57 Four-Ball Weld, ASTM D2596, kgf 500 Base Oil Viscosity: 40°C, cSt 1570

TYPICAL PROPERTIES:

D a t e 0 5 / 1 8




M20029

55

Grea

ses



Mystik Red Lithium C is a high quality multi-purpose grease fortified with additive systems to provide anti-rust, oxidation resistance, and antiwear performance.

• Antirust, antioxidant, and antiwear protection

• Water resistant

• A good quality multipurpose grease

• Intended for use in general purpose applications where normal conditions prevail


M 2 0 0 3 6

M Y S T I K ® R E D L I T H I U M C

MYSTIK® RED LITHIUM C

Material Code 665135002 NLGI Consistency Number 2 Thickener Type Lithium Stearate Texture Smooth, Medium Fiber Color Red Worked Penetration, ASTM D217 265-295 Dropping Point, ASTM D566, °F (°C) 340 (171) Oil Separation, ASTM D1742, % loss 2.5 Approximate Application Temperature Range, °F (°C) -5 to 280 (-21 to 138) Base Oil Viscosity: 40°C, cSt 150

TYPICAL PROPERTIES:

DESCRIPTION:

FEATURES:

APPLICATIONS:

D a t e 0 5 / 1 8




M20036

56

Hydraulic Fluids



Mystik Anti-Leak Industrial Oil is a very wide temperature range, multiple viscosity grade oil specially treated for maximum leakage resistance. Fortified with antiwear, antifoam, antirust, and antioxidant stabilizer additives for long life. It has a special “antisplatter” additive for splash resistance and a slower “drip off” rate. While primarily used as a combination replacement for individual ISO 46, 68, and 100 grade hydraulic fluids, this product can also be used as a medium viscosity way oil, a winter grade rock drill oil, a “non-drip” general purpose shop oil, and as a circulating oil for gears and bearings.

• A very wide temperature range, multiple viscosity grade oil, specially treated for leakage resistance. Fortified with antiwear, antifoam, antirust, and antioxidant stabilizer additives for long life.

• Has a special “antisplatter” additive for splash resistance and a slower “drip off” rate.

• While primarily used as a combination replacement for individual grade hydraulic fluids, this product is also being used as a medium viscosity way oil, a winter rock drill oil, a “non-drip” general purpose shop oil, and as a circulating oil for gears and bearings.

NSF H-2 - Lubricants with no food contact (Definition)“These compounds may be used as a lubricant, release agent, or antitrust film on equipment and machine parts or in closed systems (e.g., hudraulic systems) in locations in which there is no possibility of the lubricant or lubricated part contacting edible products.”

MYSTIK® ANTI-LEAK INDUSTRIAL OIL

Material Code 663300002 ISO Grade 100 (Recommended for 46, 68, 100) SAE Grade 15W-40 Gravity, °API ASTM D4052 30.1 Density, lb/gal @ 60°F 7.29 Viscosity ASTM D445 at 40°C, cSt 92.7 at 100°C, cSt 12.9 Viscosity Index ASTM D2270 137 Flash Point, COC, °F (°C) ASTM D92 400 (204) Pour Point, °F (°C) ASTM D97 -30 (-34) Appearance, Color Aqua Blue

TYPICAL PROPERTIES:

M Y S T I K ® A N T I - L E A K I N D U S T R I A L O I L

M 2 0 0 3 7

A Versatile and Widely Varied Purpose Lubricant

DESCRIPTION:

FEATURES:

CLASSIFICATION:

D a t e 0 5 / 1 8



M20037

56

Hydraulic Fluids

57

Hydr

aulic

Flu

ids



Mystik AW Hydraulic Oils offer excellent antiwear protection with rust, oxidation, and foam inhibitors in high quality, fully refined base stocks with good oxidation stability. They meet pump performance requirements of major manufacturers like Denison and Eaton.

• Rust, oxidation, antiwear protection, and foam resistance. Blended from high quality, fully refined base oils.

Mystik AW Hydraulic Oils meet or exceed: • ASTM D 6158 HM (2005) • General Motors LS-2 (1997) • Fives Cincinnatti P-68, 69, 70 • JCMAS HK P041 (2004) • Parker Denison HF-0 (Revision J) • ISO 11158 HM (FDIS 2008) • DIN 51524-2 (2006) • SEB 181 222 (2007) • Eaton Brochure 03-401-2010 • US Steel 126, 127, 136

• High and low pressure hydraulic systems where additive-treated product is required.

• Vane, piston, and gear pumps.

• Bearings, gears, and pumps which require an R&O or R&O/AW hydraulic oil.

MYSTIK® AW HYDRAULIC OILS

Material Code 663380002 663381002 663382002 663383002 ISO Viscosity Grade 22 32 46 68 API Gravity at 60°F ASTM D4052 33.7 32.6 31.2 30.8 Pounds/Galon at 60°F 7.13 7.18 7.24 7.26 Specific Gravity at 60°F ASTM D1298 0.856 0.862 0.870 0.872 Viscosity ASTM D445 at 40°C, cSt 22.3 32.3 46.6 68.0 at 100°C, cSt 4.45 5.59 6.96 9.0 Viscosity Index ASTM D2270 110 111 106 107 Flash Point, COC, °F (°C) ASTM D92 399 (204) 415 (213) 425 (218) 465 (241) Pour Point, °F (°C) ASTM D97 -40 (-40) -27 (-33) -22 (-30) -17 (-27) Color, ASTM D1500 L0.5 0.5 0.5 0.5

TYPICAL PROPERTIES:

M Y S T I K ® A W H Y D R A U L I C O I L S

M 2 0 0 7 0

DESCRIPTION:

FEATURES:

APPLICATIONS:

D a t e 0 5 / 1 8



M20070

58

Hydraulic Fluids



Premium quality antiwear, antileak, and antifoam hydraulic oils formulated for use in modern high and low pressure industrial and mobile hydraulic systems. They meet the toughest requirements of most manufacturers and are dyed green for ease of identification from other petroleum products. They have 100% paraffinic high VI base oils with low pour points for wide temperature range applicability and additionally are treated with antioxidant stabilizers for long life and an antirust protective additive. A fully synthetic seal swell agent prevents and stops minor leaks and provides longer seal life. They may also be used as API GL-1 gear lubricants where their viscosity is suitable. They have a variety of applications where general purpose non-detergent type oils or rust and oxidation (R&O) inhibited oils are applicable. The High Viscosity Index (HVI) products offer wide temperature application and have a typical dielectric strength of 35kV which makes them suitable for use as non conductive hydraulic fluids. HVI-32 meets FMC Corporation recommendations for a high viscosity index hydraulic fluid.

• Mystik AW/AL Hydraulic Oils meet or exceed: • ASTM D 6158 HM (2005) • General Motors LS-2 (1997)

• Fives Cincinnati P-68, 69, 70 • JMCAS HK P041(2004) • Parker Denison HF-0 (Revision J) • ISO 11158 HM (FDIS 2008) • DIN 51524-2 (2006) • SEB 18 22 (2007) • Eaton Brochure 03-401-2010 • US Steel 126-127-136

• Premium quality antiwear, antileak, and antifoam hydraulic oils

• High viscosity indexes and low pour points for wide temperature usage

• Excellent oxidation resistance and thermal stability

• Manufactured from high quality, solvent refined paraffinic base stocks

• Good water separation characteristics

• Outstanding rust and corrosion inhibition for enhanced service life

• Dyed green for ease of identification

• Highly recommended for: – bearings and gears which require an R&O or R&O/AW hydraulic oil. – hydraulic circuit components (valves, motors, servos, pumps, etc.) – applications where general non-detergent type oils are applicable – vacuum pumps – non conductive hydraulic fluid

NOTE: HVI-32 and HVI-68 are guaranteed to have a dielectric strength of no less than 28 kVwhen packaged. Dielectric strength is extremely sensitive to humidity and contamination. Once the containers are opened, the dielectric strength cannot be expected to remain at its original value. Containers should be kept tightly sealed and stored in a dry environment.

M 2 0 0 3 8

DESCRIPTION:

FEATURES:

(Continued)

M Y S T I K ® A W / A L H Y D R A U L I C O I L S

D a t e 0 5 / 1 8


M20038

59

Hydr

aulic

Flu

ids



M 2 0 0 3 8

TYPICAL PROPERTIES:

D a t e 0 5 / 1 8 - ( C o n t i n u e d )




MYSTIK® AW/AL HYDRAULIC OILS

Material Code 663303002 663304002 663305002 663306002 663312002 663314002

Designation HVI-32 HVI-68 ISO Viscosity Grade 32 46 68 100 32 68 Gravity, °API ASTM D4052 32.3 31.3 30.8 30.1 33.5 31.0 Density, lb/gal at 60°F 7.19 7.24 7.26 7.29 7.14 7.25 Specific Gravity @ 60°F ASTM D1298 0.864 0.870 0.872 0.875 0.857 0.8771 Brookfield Viscosity ASTM D2983 at -18°C, cP – – – – – – at -23.3°C, cP – – – – 1,925 9,100 at -35°C, cP – – – – 16,700 – Viscosity ASTM D445 at 40°C, cSt 32.5 46.0 68.0 98.2 31.6 68.0 at 100°C, cSt 5.55 6.92 9.0 11.5 6.61 10.8 Viscosity Index ASTM D2270 108 106 107 105 172 149 Appearance, Color Green Green Green Green Green Green Flash Point, COC, °F (°C) ASTM D92 435 (224) 435 (224) 468 (242) 471 (244) 417 (214) 453 (234) Pour Point, °F (°C) ASTM D97 -22 (-30) -22 (-30) -11 (-24) +5 (-15) -33 (-36) -27 (-33) Neutralization Number (TAN) ASTM D664 0.5 0.5 0.5 0.5 0.5 0.5 Rust Test, ASTM D665 A - Distilled Water Pass Pass Pass Pass Pass Pass B - Synthetic Sea Water Pass Pass Pass Pass Pass Pass Foam Test, ASTM D892, Sequence I, II, III Pass Pass Pass Pass Pass Pass Oxidation Test, hrs. ASTM D943 5,300 5,200 4,000 3,600 4,200+ 3,500+ Meets Denison HF-0 Requirements Yes Yes Yes Yes Yes Yes Meets Eaton Brochure– 03-401-2010 Yes Yes Yes Yes Yes Yes Dielectric Strength, kV – – – – 35 35


M20038

(Continued)

60

Hydraulic Fluids



Mystik Hydraulic Jack Oil is a low viscosity fluid providing extra low friction in hand or foot operated hydraulic systems.

• Treated with antirust, antiwear, antioxidant, and antifoam additives

• Low viscosity reduces pumping effort required and allows jack to close rapidly and completely when released

• Provides rust, wear, and oxidation protection and foam resistance. Contains low wax content, low aniline point oils to give seal swell and softening to retard leakage and provide a naturally low pour point.

• May be used at sub-zero temperatures in motorized hydraulic systems

• Can also serve as a high speed spindle oil and as a low temperature lubricant

• Easy to use package with pour spout

M 2 0 0 6 7

MYSTIK® HYDRAULIC JACK OIL

Material Code 663321002 ISO Grade (Approx.) 22 Gravity, °API @ 60°F ASTM D4052 25 Density, lb/gal at 60°F 7.53 Specific Gravity at 60°F ASTM D1298 0.9042 Viscosity ASTM D445 at 40°C, cSt 21.5 at 100°C, cSt 3.8 Viscosity Index ASTM D2270 32 Flash Point, COC, °F (°C) ASTM D97 315 (157) Pour Point, °F (°C) ASTM D97 -50 (-46) Color Red

TYPICAL PROPERTIES:

M Y S T I K ® H Y D R A U L I C J A C K O I L

DESCRIPTION:

FEATURES:

D a t e 0 6 / 1 8



M20067

61

Indu

stria

l Gas

Eng

ine

Oils



Mystik Terra 340 Gas Engine Oils are high quality lubricants compounded with a low ash detergent and an ashless dispersant, as well as oxidation and corrosion inhibitors. They are specially formulated for four-cycle naturally aspirated and turbocharged natural gas/LPG fueled engines. Use where low ash oils are permitted in low, medium, or high speed four-cycle engines. Recommended for use in high-speed four-cycle industrial engines such as Caterpillar, Cummins, Dresser-Rand (Ingersoll-Rand) Category I and II, Superior, Waukesha and Worthington. Not recommended for LPG or CNG conversions in automotive service.

• Low ash detergent and ashless dispersant formulation provides excellent deposit control for ports, spark plugs and combustion chambers

• Inhibited against rust, corrosion, oxidation, nitration, and wear

• Contains no bright stock which can cause carbon buildup in combustion chambers and engine ports

• Superior antiwear protection for piston rings and cylinder liners

• Low phosphorus chemistry for catalyst compatibility

MYSTIK® TERRA® 340 GAS ENGINE OILS

Material Code 663047002 663045002 SAE Grade 30 15W-40 Gravity, ASTM D4052, °API 30.0 30.6 Pounds/Gallon at 60°F 7.30 7.27 Specific Gravity at 60°F. 0.876 0.873 Viscosities: at 40°C, cSt 88 101.5 at 100°C, cSt 11.0 13.8 Viscosity Index 111 137 Flash Point, ASTM D92, COC, °F (°C) 466 (241) 439 (226) Pour Point, ASTM D97, °F (°C) -38 (-39) -38 (-39) Color, ASTM D1500 L4.5 L5.0 Sulfated Ash, wt % 0.4 0.4 Total Base Number, ASTM D2896, mg KOH/g 5.0 5.0 Total Acid Number, ASTM D664, mg KOH/g 1.07 1.07

TYPICAL PROPERTIES:

M Y S T I K ® T E R R A ® 3 4 0 G A S E N G I N E O I L S

M 2 0 0 4 6

Low Ash Gas Engine Oils

DESCRIPTION:

FEATURES:

D a t e 0 4 / 1 8

Mystik and Terra are registered trademarks of CITGO Petroleum Corporation. All other registered trademarks or trademarks are the property of their respective owners.



M20046

61

62

Industrial Gas Engine Oils



Mystik Terra 500 Gas Engine Oil SAE 15W-50 is a premium quality lubricant compounded with a low ash detergent and an ashless dispersant, as well as oxidation and corrosion inhibitors. It is specially formulated for four-cycle naturally aspirated and turbocharged natural gas/LPG fueled engines where an SAE 15W-50 viscosity grade is suitable for use. Use where low ash oils are permitted in low, medium, or high speed four-cycle engines. Recommended for use in high-speed, four-cycle industrial engines such as Caterpillar, Fairbanks-Morse, Superior, and Waukesha. Not recommended for LPG or CNG conversions in automotive service.

• Excellent oxidation and nitration inhibition for protection against oil thickening and outstanding viscosity control

• Superior antiwear protection

• High flash point from low volatility base stocks

• High viscosity index and low pour point for year-round performance

• Low ash technology

• Suitable for use with catalytic converters

MYSTIK® TERRA® 500 GAS ENGINE OIL SAE 15W-50

Material Code 663051002 SAE Grade 15W-50 Gravity, ASTM D4052, °API 30.7 Pounds/Gallon at 60°F 7.26 Specific Gravity at 60°F 0.872 at 40°C, cSt 131 at 100°C, cSt 17.5 Viscosity Index 148 Flash Point, ASTM D92, COC, °F (°C) 424 (218) Pour Point, ASTM D97, °F (°C) -38 (-39) Color, ASTM D1500 L5.0 Sulfated Ash, ASTM D872, wt % 0.45 Total Base Number, ASTM D2896, mg KOH/g 5.7 Total Acid Number, ASTM D664, mg KOH/g 1.4

TYPICAL PROPERTIES:

M 2 0 0 4 7

Low Ash Gas Engine Oil

DESCRIPTION:

FEATURES:

D a t e 4 / 1 8

M Y S T I K ® T E R R A ® 5 0 0 G A S E N G I N E O I L S A E 1 5 W - 5 0



M20047

63

Indu

stria

l Gas

Eng

ine

Oils



Mystik Terra Free Ashless Gas Engine Oils are premium quality lubricants compounded with a detergent and a dispersant, as well as oxidation and corrosion inhibitors. They are specially formulated for two- and four-cycle naturally aspirated and turbocharged natural gas/LPG fueled engines. Use where very low ash or ashless oils are permitted in low- to medium-speed, two- and four-cycle engines such as Ajax, Clark, Cooper-Bessemer and Dresser-Rand (Ingersoll-Rand) Category I and II generally used in gas gathering operations. An excellent choice for catalytic converter equipped engines. Not recommended for LPG or CNG conversions in automotive service.

• Specially formulated ashless stationary natural gas engine oils with an ashless dispersant provide excellent deposit control for ports, pistons, spark plugs and combustion chambers

• Ashless dispersant provides superior control of oil thickening

• Excellent oxidation and nitration inhibition for protection against oil thickening and outstanding viscosity control

• Superior antiwear, scuffing and corrosion protection

• High flash point from low volatility base stocks with low carbon-forming tendencies

• High viscosity index and low pour point for year-round performance

• Superior ashless technology

• Contains no bright stock which can cause carbon build up in combustion chambers and engine ports

Highly recommended for all natural gas and propane powered engines which specify an ashless engine oil.

MYSTIK® TERRA® FREE ASHLESS GAS ENGINE OILS

Material Code 663056002 663057002 663055002 SAE Grade 30 40 15W-40 Gravity, ASTM D4052, °API 30.1 29.8 30.8 Pounds/Gallon at 60°F 7.29 7.31 7.26 Specific Gravity at 60°F 0.875 0.878 0.872 Viscosities: at 40°C, cSt 85 117 103 at 100°C, cSt 10.8 13.4 14.0 Viscosity Index 110 111 137 Flash Point, ASTM D92, COC, °F (°C) 496 (258) 504 (262) 457 (236) Pour Point, ASTM D97, °F (°C) -33 (-36) -11 (-24) -38 (-39) Color, ASTM D1500 L1.0 L1.0 L1.0 Sulfated Ash, ASTM D872, wt % 0.06 0.06 0.06 Total Base Number, ASTM D2896, mg KOH/g 0.8 0.8 0.8 Total Acid Number, ASTM D664, mg KOH/g 0.2 0.2 0.2

TYPICAL PROPERTIES:

M Y S T I K ® T E R R A ® F R E E A S H L E S S G A S E N G I N E O I L S

M 2 0 0 4 5

DESCRIPTION:

FEATURES:

APPLICATIONS:

D a t e 0 4 / 1 8



M20045

64

Industrial Gas Engine Oils



Mystik TerraSyn Irrigation Engine Oil is an SAE 15W-40 synthetic stationary natural gas engine oil. It is specially formulated to provide lubrication in engines that have been converted to natural gas fuel, such as those in LP and agricultural irrigation pump service. Designed for added engine valve train anti-wear protection.

Mystik TerraSyn Irrigation Engine Oil provides:

• Improved engine top end start up lubrication, especially in colder environments • Enhanced valve train protection compared to conventional stationary natural gas engine oils • Excellent extended drain capability, providing user savings in downtime, work man-hours and

oil usage

MYSTIK® TERRASYNTM IRRIGATION ENGINE OIL

Material Code 663061002 SAE Grade 15W-40Gravity, ASTM D4052, °API 31.6Density, lbs/gal 7.22Flash Point, ASTM D92 (COC), °F (°C) 489 (254)Viscosity, ASTM D445, cSt at 40°C 107cSt at 100°C 15.1Viscosity Index, ASTM D2270 147CCS Viscosity, ASTM D5293, cP -20C 5,340 -25C 9,300MRV Viscosity, ASTM D4684, cP -25C 10,700Pour Point, ASTM D97, °F (°C) -60 (-51)Color, ASTM D1500 6.0Sulfated Ash, ASTM D874, m% 0.45TBN, ASTM D2896 5.0Zinc, ppm 900

TYPICAL PROPERTIES:

M 2 0 1 0 0

DESCRIPTION:

D a t e 0 6 / 1 8

M Y S T I K ® T E R R A S Y N T M I R R I G A T I O N E N G I N E O I L

Mystik is a registered trademark and TerraSyn is a trademark of CITGO Petroleum Corporation. All other registered trademarks or trademarks are the property of their respective owners.


M20100

65

Func

tiona

l Pro

duct

s



Mystik Bar and Chain Lubricant is a great choice for loggers as well as home and ranch users. It utilizes special components to reduce wear, guard against rust and enhance metal adhesion to reduce spatter.

Designed for use over a wide temperature range. For use in all brands of chain saws.

• Lubricates and Cools Chain

• Polymer Controls Spatter

• Guards Against Rust

• Provides Wear Protection

NOTE: NOT FOR USE IN ENGINES! Use Mystik JT-4® 2-Cycle Lawn and Garden Engine Oil, Material Code 663091002, where 2-cycle engine oil is specified.

MYSTIK® BAR AND CHAIN LUBRICANT

Material Code 663605002 SAE Grade 30 ISO Viscosity Grade 100 Gravity, °API ASTM D4052 30 Pounds/Gallon @ 60°F 7.3 Flash Point, COC, °F (°C) ASTM D92 340 (171) Pour Point, °F (°C) ASTM D97 -23 (-10) Viscosity ASTM D445 cSt at 40°C 82 cSt at 100°C, 10 Appearance, Color Blue-Green

TYPICAL PROPERTIES:

M Y S T I K ® B A R A N D C H A I N L U B R I C A N T

M 2 0 0 4 8

DESCRIPTION:

FEATURES:

D a t e 0 5 / 1 8



M20048

65

66

Functional Products



Mystik Rock Drill Oil 150 is formulated to provide excellent extreme pressure (EP) and anti-wear performance in heavy duty pneumatic tools.

Mystik Rock Drill Oil 150 provides:

• Excellent EP and anti-wear performance

• Emulsification properties for extra lubricity in moist or wet conditions

• Tackiness to reduce “splatter” and non drip properties

Recommended for rock drills, jack hammers and other pneumatic tools requiring premium performance lubrication. Can also be used in industrial slideway (way oil) or non-drip oil applications.


MYSTIK® ROCK DRILL OIL 150



SAE Viscosity Grade (Approx.) 40 Gravity, °API ASTM D4052 29.1 Density, lb/gal @ 60°F 7.34 Flash Point, COC, °F (°C) ASTM D92 475 (246) Pour Point, °F (°C) ASTM D97 5 (-15) Viscosity ASTM D445 cSt. at 40°C 146 cSt. at 100°C 15.5 SUS at 100°F 764 SUS at 210°F 81.73 Viscosity Index ASTM D2270 108 Color, ASTM D1500 4.0 Timken OK Load, lbs. ASTM D2782 >65 Falex Load, lbs. ASTM D3233 >2000

TYPICAL PROPERTIES:

M Y S T I K ® R O C K D R I L L O I L 1 5 0

M 2 0 0 5 5

Heavy Duty Pneumatic Tools Oil

DESCRIPTION:

FEATURES:

APPLICATIONS:

D a t e 0 5 / 1 8




M20055

67

Func

tiona

l Pro

duct

s



Mystik Tuff-Torq EG is a modern highly advanced formula, field and performance proven, high-pressure tool joint compound. It utilizes a proprietary non-metallic additive system that provides an environmental alternative which rivals the performance of API thread compounds containing detrimental metal compounds such as lead, zinc or antimony without compromising performance.

Customers report that this product has been field-proven to provide superior lubricity and blowout prevention in wells drilled to depths of 12,000 feet. Mystik Lubricants Tuff-Torq EG can be used as a drill collar compound, storage compound or production tube sealer with excellent results.

• Mystik Tuff-Torq EG utilizes an additized lithium stearate thickener which provides improved thread adhesion and exceptional sealing properties. The special compounding includes a leak preventer that reduces leaks and washout.

• It applies easily over a range of temperatures and conditions.

• It is resistant to washout and will not harden or bleed excessively in storage.

• The Break Out Ratio performance of Mystik Tuff-Torq EG rivals that of other thread compounds that contain 60% lead.

• Formulated with a proprietary non-metallic additive system; does not contain metallic zinc, lead, or copper additives.

• Provides exceptional anti-weld performance.

• An environmentally conscious product that has been formulated to provide a superior level of performance while imparting minimal environmental impact.

• Storage compound for pipe yards

• Drill collar compound

• Production tube thread compound

• Raise Bore Drilling DI-22 Rotary Shouldered Connections

M Y S T I K ® T U F F - T O R Q E G ®

M 2 0 0 5 6

Tool Joint Compound – An Environmentally Conscious Product

DESCRIPTION:

FEATURES:

APPLICATIONS:

D a t e 0 5 / 1 8

Drill Stem Pipe ThreadBOR on 10.25 MTI 315 Pipetik

(Continued)

BOR on 10.25 MTI 315 Pipetik

0.610.620.630.640.650.66

Tuff-Torg EG New

Competitor A

Reverse Bore Head


M20056

68

Functional Products



TYPICAL PROPERTIES:

MYSTIK® TUFF-TORQ EG®

Material Code 665053002 NLGI Consistency Grade 1 Thickener Type Lithium Stearate Texture Coarse/Granular Color Dark Brown Specific Gravity at 77°F 1.12 Unworked Penetration, ASTM D217 310-340 Dropping Point, °F (°C) ASTM D2265 290 (143) Brushability, °F (°C) To 40 (4.4) Four-Ball Wear, mm D2266 0.40 Four-Ball EP Load Wear Index ASTM D2596 50 Four-Ball EP Weld Point, kgf ASTM D2596 500

D a t e 0 5 / 1 8 - ( C o n t i n u e d )

M 2 0 0 5 6

M Y S T I K ® T U F F - T O R Q E G ®

Mystik and Tuff-Torq EG are registered trademarks of CITGO Petroleum Corporation. All other registered trademarks or trademarks are the property of their respective owners.


M20056

(Continued)

69

Func

tiona

l Pro

duct

s



Mystik Turbine Drip Oil is formulated with highly refined lubricating base oils and inhibited with a foam suppressant. It is for use in dripper lubrication systems for irrigation water well line shaft bearings where a food grade registered product is NOT required. NOTE: This lubricant is not recommended for use where a food grade quality lubricant is required. This product should not be used for potable water well pump lubrication. It is the user’s responsibility to ensure proper selection of lubricating oil for agricultural irrigation and related systems; refer to applicable regulatory agency requirements.

MYSTIK® TURBINE DRIP OIL

Material Code 663435002 SAE Grade 10W ISO Grade 32 Gravity, °API ASTM D4058 24.8 Density, lb/gal at 60°F 7.54 Specific Gravity @ 60°FASTM D1298 0.9053 Viscosity, Brookfield @ -25°C, cP ASTM D2893 6400 Viscosity ASTM D445 at 40°C, cSt 29.3 at 100°C, cSt 5.0 at 100°F, cSt (SUS) 150 at 210°F, cSt (SUS) 42.4 Viscosity Index ASTM D2270 86 Flash Point, COC, °F (°C) ASTM D92 380 (193) Pour Point, °F (°C) ASTM D97 -25 (-32) Color, ASTM D1500 3.0

TYPICAL PROPERTIES:

M Y S T I K ® T U R B I N E D R I P O I L

M 2 0 0 5 7

DESCRIPTION:

FEATURES:

D a t e 0 5 / 1 8



M20057

70

Functional Products



Mystik ViscidLube Oil Treatment is a special polymer-rich treatment. May be added to crankcase of warm, running engine, using 8-16 ozs. of Mystik ViscidLube to 4 quarts of motor oil to help reduce oil consumption problems. DO NOT OVERFILL CRANKCASE.

Builds high temperature viscosity with small effect on low temperature fluidity. Contains an effective anti-wear and anti-oxidant additive system. Compatible with conventional and synthetic based motor oils for gasoline and diesel engines.

Mystik ViscidLube has excellent adherence to metal. Use neat or mixed with 50% motor oil in engine repair and assembly as a pre-lubricant to protect critical parts and help with parts positioning. • Excellent pre-assembly lube

• Increases oil pressure; retards oil leakage and oil consumption

• Raises viscosity at high temperatures with minimal effect on low temperature fluidity and cold weather start-up

• Exhibits good shear stability (resistance to viscosity loss in service)

• Provides additional antiwear and antioxidation protection to prevent wear and deposits on cams, lifters, pistons, rings, and bearing

Consult owner’s manual for proper lubricant requirements.

MYSTIK® VISCIDLUBE® OIL TREATMENT

Material Code 663618002 Gravity, °API ASTM D4052 32.0 Density, lb/gal @ 60°F 7.21 Specific Gravity @ 60°F ASTM D1298 0.8655 Viscosity ASTM D445 at 40°C, cSt 9757 at 100°C, cSt 805 Viscosity Index ASTM D2270 297 Flash Point, COC, °F (°C) ASTM D92 350 (177) Pour Point, °F (°C) ASTM D97 0 (-18) Color, ASTM D1500 2.0

TYPICAL PROPERTIES:

M Y S T I K ® V I S C I D L U B E ® O I L T R E A T M E N T

M 2 0 0 5 4

DESCRIPTION:

FEATURES:

D a t e 0 5 / 1 8

Mystik and ViscidLube are registered trademarks of CITGO Petroleum Corporation. All other registered trademarks or trademarks are the property of their respective owners.



M20054

71

Func

tiona

l Pro

duct

s



Mystik Non-Detergent General Purpose Oils are designed for use in non-critical applications where a general purpose oil is desired. This includes low pressure hydraulic systems such as hydraulic jacks and air compressors requiring a non-detergent type lubricant. They are available in SAE 10W, 20W-20, and 30 viscosity grades. Mystik Non-Detergent General Purpose Oils are not recommended for use in gasoline or diesel engines.

MYSTIK® NON-DETERGENT GENERAL PURPOSE OILS

Material Code 663111002 663112002 663113002

SAE Grade 10W 20W-20 30ISO Grade (Approx.) 32 68 100Density, lb/gal at 60°F (Approx.) 7.54 7.6 7.65Viscosities (Approx.): at 100°C, cSt 5.0 8.0 11 at 40°C, cSt 29 62 119 at 210°F, SUS 44 54 — at 100°F, SUS 165 340 —Viscosity Index 95 95 95Flash Point, ASTM D92, °F (°C) 380 (193) 395 (202) 425 (218)Pour Point, ASTM D97, °F (°C) -25 (-32) -10 (-23) -5 (-20)

TYPICAL PROPERTIES:

NOTE: Consult machinery operator’s manual for proper viscosity grade. For gasoline or diesel engines, consider Mystik JT-8 engine oils.

M Y S T I K ® N O N - D E T E R G E N T G E N E R A L P U R P O S E O I L S

M 2 0 0 9 0

DESCRIPTION:

D a t e 0 5 / 1 8

Mystik is a registered trademark of CITGO Petroleum Corporation.



M20090

72

Compressor Lubricants



Mystik Ammonia Compressor Oil 68 is blended from high quality naphthenic base oils to meet the performance requirements of ammonia refrigeration compressors. This oil offers the stability and low temperature characteristics necessary for the proper lubrication of this type equipment. It will not “wax out” under the low temperature conditions typically encountered in these systems. Equipment lines and refrigerant control devices stay clear and system efficiency is not impaired. This oil is chemically and thermally stable under the conditions normally encountered in ammonia refrigeration systems. It satisfies the low temperature requirements of all but the most extreme low temperature applications. • Blended with high-quality naphthenic base oils

• Low pour point to meet the low temperature conditions of ammonia compressors

• High flash point from low volatility base stocks to reduce vaporization at discharge temperatures and pressures

• Available in ISO Viscosity Grade 68 which is required by most ammonia compressor manufacturers NSF H-2 - Lubricants with no food contact (Definition) “These compounds may be used as a lubricant, release agent, or antirust film on equipment and machine parts or in closed systems (e.g., hydraulic systems) in locations in which there is no possibility of the lubricant or lubricated part contacting edible products.”

MYSTIK® AMMONIA COMPRESSOR OIL 68

Material Code 663346002 ISO Viscosity Grade 68 Gravity, °API @ 60°F ASTM D4052 23.5 Density @ 60°F, lb/gal 7.61 Specific Gravity @ 60°F ASTM D1298 0.913 Flash Point, COC, °F (°C) ASTM D92 380 (193) Viscosity ASTM D445 cSt at 40°C 64.1 cSt at 100°C 7.3 cSt (SUS) at 100°F 72.3 (335.5) cSt (SUS) at 210°F 7.6 (51.0) Viscosity Index ASTM D2270 63 Pour Point, °F (°C) ASTM D97 -40 (-40) Color, ASTM D1500 2.0

TYPICAL PROPERTIES:

M Y S T I K ® A M M O N I A C O M P R E S S O R O I L 6 8

M 2 0 0 6 3

DESCRIPTION:

FEATURES:

CLASSIFICATION:

D a t e 0 5 / 1 8



M20063

72

Compressor Lubricants

73

Agric

ultu

ral P

rodu

cts



M Y S T I K ® J T - 8 ® P R E M I U M G A S O L I N E M O T O R O I L S

Mystik JT-8 Premium Gasoline Motor Oils, with their advanced, fuel efficient synthetic blends formula, exceed the latest warranty requirements of car manufacturers for gasoline engines and meet the latest API Performance and Resource Conserving ratings. The premium quality detergent/dispersant formulation guards against sludge, reduces deposits and protects against rust, corrosion and wear. Mystik JT-8 Premium Gasoline Motor Oils provide optimum viscosity and thermal stability and are highly recommended for all carburetor-equipped or fuel-injected gasoline engines including turbocharged, supercharged and other high performance models. These products offer maximum protection against deposits and have superior durability. Even under severe service conditions you can have complete confidence that your engine oil is providing the fullest protection possible.

• The 5W-20, 5W30 and 10W-30 viscosity grades are recommended for applications calling for oils meeting ILSAC GF-5 and API SN Plus.

• All viscosity grades are licensed for API SN Plus and are backward compatible with prior service categories (SM, SL, SJ and SH).

• Special friction modifier provides increased fuel economy

• Multi-viscosity, thermally stable and durable formulation provides maximum year-round protection

Consult owner’s manual for fluid selection.

MYSTIK® JT-8® PREMIUM GASOLINE MOTOR OILS

Material Code 663013002 663012002 663011002

SAE Grade 5W-20 5W-30 10W-30 Gravity, ASTM D4052, °API 32.0 32.4 30.8 Pounds/Gallon at 60°F 7.20 7.19 7.26 Specific Gravity at 60°F 0.865 0.863 0.872 Viscosities: at -25°C, cP Max – – 5,820 at -30°C, cP Max 6,170 5,360 – at 40°C, cSt 49.2 60.0 67.5 at 100°C, cSt 8.3 9.9 10.1 Viscosity Index 144 151 134 Flash Point, ASTM D92, COC, °F (°C) 442 (228) 450 (232) 451 (233) Pour Point, ASTM D97, °F (°C) -33 (-36) -38 (-39) -33 (-36) Color, ASTM D1500 L3.5 L3.5 L3.5

TYPICAL PROPERTIES:

M 2 0 0 0 1

DESCRIPTION:

FEATURES:

D a t e 0 6 / 1 8



M20001

73

74

Agricultural Products




Mystik JT-8 Premium Gasoline Synthetic Motor Oils are well-balanced combinations of today’s highest quality synthetic base stocks and contain an advanced additive system that meets stringent automotive specifications. They are designed to provide excellent protection in today’s high performance gasoline (including turbocharged and supercharged) engines in passenger cars, vans, sport utility vehicles, and light trucks. These synthetic engine oils demonstrate improved performance in today’s advanced engine designs, and are available in SAE 0W-20, 5W-20 and 5W-30 viscosity grades.

• Excellent low-temperature starting and pumpability characteristics

• High-temperature/high-shear properties well above conventional oils

• Lower volatility when compared to conventional oils

• Meets the most advanced emissions and fuel economy standards in the US gasoline engines

• Enhanced protection against varnish buildup and sludge formation in critical engine parts for top performance and long engine life

• Extended engine life due to control of wear and deposit formation

• Compatible with conventional and synthetic motor oils

• Mystik® JT-8® Premium Gasoline Synthetic SAE 0W-20 Approved GM dexos1® Gen2 License D10392HG121

• Mystik® JT-8® Premium Gasoline Synthetic SAE 5W-20 Approved GM dexos1® Gen2 License D10744HL121

• Mystik® JT-8® Premium Gasoline Synthetic SAE 5W-30 Approved GM dexos1® Gen2 License D10372HF121

Mystik JT-8 Premium Gasoline Synthetic Motor Oils are recommended for passenger cars, sport utility vehicles and light trucks operating on gasoline. They are also recommended for use in gasoline engines which have been converted to operate on compressed natural gas (CNG), liquified natural gas (LNG), and liquified petroleum gas (LPG-which includes propane and butane). Consult the vehicle owners manual for proper engine lubricant selection.

Mystik JT-8 Premium Gasoline Synthetic Motor Oils meet the performance requirements for the latest gasoline-fueled engine service ILSAC GF-5/Resource Conserving and API SN Plus and display the API Certification Mark and API Service Symbol. They have also demonstrated benefits in industry accepted fuel economy tests.

Mystik JT-8 Premium Gasoline Synthetic 0W-20 Motor Oil meets the GM dexos1® Gen2 specification and is recommended for Original Equipment Manufacturers (OEM) such as Toyota and Honda for some hybrid vehicle applications and a limited number of low temperature applications.

Mystik JT-8 Premium Gasoline Synthetic Motor Oil SAE 5W-30 meets the GM dexos1® Gen2 specification and provides excellent performance where GM4718M or GM6094M is referenced.

Note: Mystik JT-8 Premium Gasoline Synthetic Motor Oils are not recommended for use in diesel engines in passenger cars, vans or light trucks. Mystik JT-8 SHD Motor Oils are recommended for diesel applications.

DESCRIPTION:

FEATURES:

(Continued)

D a t e 0 6 / 1 8

M 2 0 0 8 2


M20082

75

Agric

ultu

ral P

rodu

cts



TYPICAL PROPERTIES:

MYSTIK® JT-8® PREMIUM GASOLINE SYNTHETIC MOTOR OILS

Material Code 663032002 663024002 663014002

SAE Grade 0W-20 5W-20 5W-30 Gravity, ASTM D4052, °API 35.0 34.5 34.2 Pounds Per Gallon 7.08 7.10 7.11Flash Point, ASTM D92, °F (°C), COC 220 (428) 442 (228) 450 (232)Low Temperature Cranking, ASTM D5293 Temperature, °F (°C) -28 (-35) -22 (-30) -22 (-30)Viscosity, cP 5,190 5,270 4,080Viscosity, ASTM D445, cSt at 140°C 46.0 52.0 58.5Viscosity, ASTM D 445, cSt at 100°C 8.5 8.7 10.5Viscosity Index, ASTM D2270 164 145 171Pour Point, ASTM D97, °F (°C) -33 (-36) -33 (-36) -27 (-33)Color, ASTM D1500 L3.5 L3.5 L3.5ILSAC GF-5 Yes Yes YesAPI SN Plus Yes Yes YesResource Conserving Yes Yes YesGM dexos1® Gen2 Approved Yes Yes Yes

D a t e 0 6 / 1 8 - ( C o n t i n u e d )


M 2 0 0 8 2



M20082

(Continued)

76




M 2 0 0 7 3

Mystik® JT-8® Synthetic Engine Oil, SAE 5W-40 , full synthetic super heavy duty engine oil,engineered with proprietary additive technology, delivers an extra level of performance for both olderand newer engines. The careful balance of synthetic components gives improved fuel economy,improved cold temperature performance and improved engine drain interval optimization capabilities.Mystik® JT-8® Synthetic Engine Oil, SAE 5W-40 meets the API CK-4 requirements, which is anexcellent choice for equipment owners who need maximum engine durability, fuel efficiency, extendedoil service capability and superior cold weather start-up performance.

• Up to 3% fuel economy advantage over SAE 15W-40 viscosity grade oils• Improves cold cranking, extending starter/battery life and reducing dependency on block heaters, saving energy• Double the oil durability protection compared to conventional CJ-4 engine oils. Always follow OEM recommendations when extending oil drain intervals• Superior lubrication in extreme temperature ranges compared to conventional SAE 15W-40 viscosity grade oils.

API CK-4, CJ-4, CI-4 PLUS, CI-4, CH-4Caterpillar ECF-3Cummins CES 20086Detroit Diesel DFS 93K 222Volvo/Mack/Renault – VDS-4.5/EOS-4.5/RLD-4PaccarNavistar

DESCRIPTION:

FEATURES:

RECOMMENDEDFOR:

(Continued)

D a t e 0 6 / 1 8


Category

Mystick JT-8 Synthtic Blend

SHD 15W-40 API CJ-4

Mystick JT-8 10W-30

API CK-4

Mystick JT-8 15W-40

API CK-4

Mystick JT-8 5W-40

API CK-4

Back Serviceable Yes Yes Yes Yes

Oxidation Stability ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

Shear Stability ✔ ✔ ✔ ✔ ✔ ✔✔

Aeration Control ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

Wear Control ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔

Fuel Efficiency ✔ ✔ ✔ ✔ ✔ ✔

Low Tempurature Start-up ✔ ✔ ✔ ✔ ✔ ✔ ✔

Compatible with API CJ-4 Oil Yes Yes Yes Yes


M20073

77

Agric

ultu

ral P

rodu

cts



D a t e 0 6 / 1 8 - ( C o n t i n u e d )

M 2 0 0 7 3

TYPICAL PROPERTIES:

MYSTIK® JT-8® SYNTHETIC ENGINE OIL, SAE 5W-40


SAE Grade 5W-40 Gravity, ASTM D4052, °API 34.0 Pounds Per Gallon 7.14 Flash Point, COC, ASTM D92, °F (°C) 450 (232) Viscosity, ASTM D445, cSt at 40°C 87

cSt at 100°C 14 Viscosity Index, ASTM D2270 166 CCS Vis, ASTM D5293, cP at °C 6,260 at -30°CMRV Vis, ASTM D4684, cP at °C 30,054 at -35°CMRV Yield Stress, ASTM D4684, Pa at °C <35Pour Point, ASTM D97, °F (°C) -44 (-42)TBN (Total Base No.), ASTM D2896 11 Color, ASTM D1500 L5.5




M20073

(Continued)

78




M Y S T I K ® J T - 8 ® S Y N T H E T I C B L E N D S U P E R H E A V Y D U T Y E N G I N E O I L S M O N O G R A D E S

M 2 0 0 9 7

Mystik JT-8 Synthetic Blend Super Heavy Duty Engine Oils are recommended for hydraulic systems, transmissions and engines that recommend a Monograde engine oil type lubricant. Mystik JT-8 Synthetic Blend Super Heavy Duty Engine Oils are formulated with premium base oils and additives to reduce wear and extend component life.

• Recommended for Service Category CF (obsolete)• Recommended for Service Category CF-2 (obsolete)• Hydraulic systems where engine oils are recommended

TYPICAL PROPERTIES:

MYSTIK® JT-8® SYNTHETIC BLEND SUPER HEAVY DUTY ENGINE OILS MONOGRADES

Material Code 663000 663006 663007 663008

SAE Grade 10W 30 40 50 Gravity, ASTM D4052, °API 32.4 30.0 29.2 27.8 Density, lbs/gal 7.19 7.30 7.33 7.40 Specifc Gravity at 60F 0.863 0.876 0.880 0.888 Flash Point, ASTM D92 (COC), °F (°C) 439 489 486 482 Viscosity, ASTM D445, cSt at 40°C 39 93.1 121 206

cSt at 100°C 6.6 11.7 13.9 19.5 Viscosity Index, ASTM D2270 123 116 113 107 CCS Viscosity, ASTM D5293, cP 3900 at -25C NR NR NR MRV Pumpability, ASTM D4684, cP 9180 at -30C NR NR NR MRV Yield Stress at -25°C, ASTM D4684 <35 at -30C NR NR NR Pour Point, ASTM D97, °F (°C) -38 (-39) -33 (-36) -33 (-36) -22 (-30) Color, ASTM D1500 L3.0 L2.5 L2.5 L3.5 Sulfated Ash, ASTM D874, m% 0.92 0.92 0.92 0.92

NR = Requirement

DESCRIPTION:

D a t e 0 6 / 1 8

APPLICATIONS:



M20097

79

Agric

ultu

ral P

rodu

cts



M 2 0 1 0 6

Mystik JT-8 Synthetic Blend Super Heavy Duty Engine Oils are performance engineered with proprietary additive technology. Designed to ensure long lasting engine durability under the toughest operating conditions. Meets the performance demands of newer engine hardware.

Mystik JT-8 Synthetic Blend Super Heavy Duty Engine Oils are recommended for commercial over-the-road fleets, agriculture, construction equipment, buses, automobiles, and other similar diesel-powered applications where a premium quality engine oil is required.

• Engineered to provide long engine life in challenging service conditions

• Double the oil durability protection compared to conventional CJ-4 engine oils. Always follow OEM recommendations when extending oil drain intervals

• Maintains viscosity over extended service intervals, even under extreme operating conditions

• Recommended for low emission Tier 4 and on-highway low emission engines

• SAE 10W-30 improves fuel economy up to 3% compared to conventional 15W-40 viscosity grade oils

DESCRIPTION:

(Continued)

PERFORMANCECAPABILITIES:

D a t e 0 6 / 1 8


Notes: • Consult owner's manual for proper SAE viscosity grade and API Service Category.

• Optimum drain intervals can be achieved utilizing oil analysis in conjunction with OEM guidelines.

SAE VISCOSITY GRADE 10W-30 15W-40

RECOMMENDED FOR:

CK-4 ✔ ✔

CJ-4 ✔ ✔

CI-4 PLUS ✔ ✔

CI-4 ✔ ✔

CH-4 ✔ ✔

SN — ✔

Caterpillar ECF-3 ✔ ✔

Cummins CES 20086 ✔ ✔

Detroit Diesel 93K222 ✔ ✔

Volvo/Mack/Renault/VDS-4.5/EOS-4.5/RLD-4 ✔ ✔

Paccar ✔ ✔

Navistar - International ✔ ✔

Ford WSS-M2C171-F1 ✔ ✔


M20106

80




D a t e 0 6 / 1 8 - ( C o n t i n u e d )

M 2 0 1 0 6

TYPICAL PROPERTIES:

MYSTIK® JT-8® SYNTHETIC BLEND SUPER HEAVY DUTY ENGINE OILS

Material Code 625775002 625776002

SAE Grade 10W-30 15W-40 Gravity, ASTM D4052, °API at 60°F 31.5 30.8 Pounds/Gallon at 60°F 7.25 7.30 Specific Gravity at 60°F 0.87 0.88Viscosity at 40°C, cSt 79 112

100°C, cSt 11.9 15.2Viscosity Index 143 141 CCS Viscosity, cP, @ Temperature 5,830 @ -25°C 4370 @ -20°CMRV Viscosity, cP, @ Temperature 20,000 @ -30°C 15,620 @ -25°CMRV Yield Stress, Pa, @ Temperature <35 <35Pour Point, °F (°C) -38 (-39) -33 (-36)Flash Point, COC, °F (°C) 432 (222) 450 (232)Noack Evaporative, ASTM D5800, % Loss 11.6 10.7 Color, ASTM D1500 L3.0 L3.5Total Base Number, ASTM D2896 10 10Sulfated Ash, ASTM D874, % wt 1.0 1.0______ Mystik and JT-8 are registered trademarks of CITGO Petroleum Corporation. All other registered trademarks or trademarks are the property of their respective owners.


CategoryMystik® JT-8

API CJ-4Mystik® JT-8

API CK-4

Back serviceable YES YES

Viscosity grades 15W-40/10W-30 15W-40/10W-30

Fleet million mile engine test rating Better Best

100% improved oxidation stability NO YES

Greater shear stability vs. conventional API CJ-4 YES YES

Aeration control vs. conventional API CJ-4 Better Best

SAE 10W-30 sustains improved fuel economy through 50,000 miles

Better Best

Compatible with conventional API CJ-4 oils YES YES

Best Overall Performance and Backward compatibility Better Best

API Comparison Chart



M20106

(Continued)

81

Agric

ultu

ral P

rodu

cts



M Y S T I K ® J T - 8 ® S Y N T H E T I C B L E N D S U P E R H E A V Y D U T Y E N G I N E O I L S S A E 1 0 W - 4 0 A N D S A E 1 5 W - 5 0

M 2 0 0 9 6

Mystik JT-8 Synthetic Blend Super Heavy Duty Engine Oil SAE 10W-40 provides an improvement in cold weather start up lubrication while providing excellent wear protection at higher operating temperatures.

Mystik JT-8 Synthetic Blend Super Heavy Duty Engine Oil SAE 15W-50 is designed for the equipment owner operating with older equipment with higher hours or miles that can benefit from a higher viscosity grade heavy duty engine oil.

Both SAE grades are engineered to provide excellent protection for equipment operating in severe conditions and will provide extended diesel engine life.

Mystik JT-8 Synthetic Blend Super Heavy Duty Engine Oils SAE 10W-40 and SAE 15W-50 are recommended for commercial over-the-road fleets, construction equipment, buses and other similar diesel-powered applications where premium quality engine is required.

TYPICAL PROPERTIES:

MYSTIK® JT-8® SYNTHETIC BLEND SUPER HEAVY DUTY ENGINE OILS SAE 10W-40 AND SAE 15W-50

Material Code 663002 663004

SAE Grade 10W-40 15W-50 API Service Category CK-4 CI-4 Plus Gravity, ASTM D 4052, °API 31.5 30.3 Density, lbs/gal 7.23 7.28 Flash Point, ASTM D 92 (COC), °F (°C) 442 (228) 440 (227) Viscosity, ASTM D 445, cSt at 40°C 105 151

cSt at 100°C 15.6 19.5 Viscosity Index, ASTM D 2270 157 148 CCS Viscosity, ASTM D 5293, cP 5700 at -25C 5300 at -20C MRV Pumpability, ASTM D 4684, cP 39,000 at -30C 23,100 at -25C MRV Yield Stress at -25°C, ASTM D 4684 <35 at -30C <35 at -25C Pour Point, ASTM D 97, °F (°C) -49 (-45) 49 (-45) Color, ASTM D 1500 L3.5 L4.0 Sulfated Ash, ASTM D 874, m% 1.0 1.0

DESCRIPTION:

D a t e 0 5 / 1 8



M20096

82




M 2 0 0 8 0

Mystik JT-4 Synthetic 4-Cycle All-Terrain Vehicle Motor Oils utilize premium synthetic base oils combined with a special additive system to provide outstanding protection for high performance All-Terrain Vehicle (ATV) and Utility Vehicle (UTV) engines. These full synthetic formulas provide optimum high and low temperature performance while minimizing volatility. This balance of synthetic technologies enhance fuel economy, improve cold temperature performance, and high temperature thermal and oxidation stability.

The advanced additive systems are specifically designed for use in ATV and UTV engines. They provide superior protection against engine wear, rust and corrosion, and ensures engine cleanliness. Mystik JT-4 Synthetic 4-Cycle All-Terrain Vehicle Motor Oils, available in SAE 0W-40, SAE 10W-40 and SAE 10W-50 grades, provide extra protection for gasoline powered ATV and UTV engines requiring a JASO MA quality oil.

• Protect in extreme hot and cold temperatures• Permit lubrication flow during cold weather start-up• Promote longer engine life by reducing wear, rust and corrosion• Provide excellent thermal and oxidation stability• Improve equipment productivity and reliability

For use in 4-cycle gasoline powered ATV and UTV engines including those manufactured by Arctic Cat, Bombardier, Honda, Kawasaki, Polaris (including 1000 ProStar), Yamaha, and other original equipment manufacturers. Ideal for high performance engines operating in extreme low and high temperatures and where performance demands the most from your oil. Select the SAE 0W-40 grade, if frequent usage at low temperatures is expected. Consult your owner’s manual for proper lubricant selection.

Mystik JT-4 Synthetic All-Terrain Vehicle Motor Oils are recommended for use in 4-cycle gasoline powered ATV and UTV engine applications requiring a JASO MA quality oil. Designed to be used in wet clutch applications that require JASO MA quality oil.

DESCRIPTION:

FEATURES:

RECOMMENDED:

APPLICATIONS:

TYPICAL PROPERTIES:

M Y S T I K ® J T - 4 ® S Y N T H E T I C 4 - C Y C L E A L L - T E R R A I N V E H I C L E M O T O R O I L S

MYSTIK® JT-4® SYNTHETIC 4-CYCLE ALL-TERRAIN VEHICLE MOTOR OILS

Material Codes 663079002 663080002 663085002SAE Grade 0W-40 10W-40 10W-50Gravity, ASTM D287, °API 33.8 31.9 33.5 Density, lbs/gal 7.13 7.21 7.14Flash Point, ASTM D92, COC, °F (°C) 428 (220) 453 (234) 457 (236)Pour Point, ASTM D97, °F (°C) –56 (–51) –22 (–30) -39 (-39) Viscosity, ASTM D445 cSt @ 40°C 93 98.4 126.6 cSt @ 100°C 14.8 14.9 17.85Viscosity Index, ASTM D2270 166 158 157CCS Viscosity, cP (°C), ASTM D5293 6000 (–35) 5660 (–25) 6592 (-25)NOACK Volatility, ASTM D5800, % Loss 7.0 9.0 7.4Color, ASTM D1500 2.5 2.5 2.5Sulfated Ash, ASTM D874, m% 0.9 1.0 1.0TBN, ASTM D2896, mg KOH/g 9.5 9.2 8.05

D a t e 0 6 / 1 8




M20080

83

Agric

ultu

ral P

rodu

cts



M Y S T I K ® J T - 4 ® 2 - C Y C L EL A W N A N D G A R D E N E N G I N E O I L

M 2 0 0 8 4

Mystik JT-4 2-Cycle Lawn and Garden Engine Oil is a premium performance synthetic blend lubricant designed for use in high performance air-cooled 2-cycle generators, chain saws, lawn mowers, snow blowers, leaf blowers, and trimmers.

Mystik JT-4 2-Cycle Lawn and Garden Engine Oil is engineered for lower smoke and advanced protection for air cooled 2-cycle engines. This synthetic blend formula meets or exceeds the rigorous requirements of the API TC, JASO FD, FC and ISO-L-EGD classifications for 2-cycle air-cooled engine oils and also exceeds the performance requirements for JASO FC, JASO FB; ISO-L-EGC and -EGB. This advanced oil helps to protects today’s high RPM air cooled 2-cycle engines against exhaust port blocking, combustion chamber and piston deposits, ring sticking and scuffing, and wear. The JASO FD Certification number for this lubricant is 001 MYS 091.

Mystik JT-4 2-Cycle Lawn and Garden Engine Oil is formulated with premium base oils and a new low ash additive package that provides excellent lubricity and detergency performance which surpasses the standard for preventing piston and combustion chamber deposits. In addition, Mystik JT-4 2-Cycle Lawn and Garden Engine Oil is a synthetic blend which reduces exhaust smoke and prevents piston seizure and cylinder scuffing. Mystik JT-4 2-Cycle Lawn and Garden Engine Oil mixes readily with fuel for pre-mix type, even at low temperatures.

Mystik JT-4 2-Cycle Lawn and Garden Engine Oil is recommended for use in air-cooled, 2-cycle applications where an API TC, JASO FD, FC or ISO-L-EGD product is preferred. It can be used in either premix or oil injection systems up to 50:1 fuel to oil ratios. Do not use in engines requiring an NMMA TC-W3, TC-WII, or TC-W product. Consult owner’s manual for fluid specifications.

Mystik JT-4 2-Cycle Lawn and Garden Engine Oil can be used in 2-cycle powered generators, chain saws, lawn mowers, snow blowers, leaf blowers, and trimmers operating in hot, dirty, dusty environments and high loads for extended periods. Mystik JT-4 2-Cycle Lawn and Garden Engine Oil provides the necessary protection to keep your air-cooled 2-cycle engine running cleaner, longer and with less smoke.

DESCRIPTION:

QUALITIES:

APPLICATIONS:

TYPICAL PROPERTIES:

MYSTIK® JT-4® 2-CYCLE LAWN AND GARDEN ENGINE OIL


Gravity, ASTM D4052, °API 32.0Density, lb/gal, at 60°F 7.21Flash Point, PMCC, ASTM D93, °F (°C) 185 (85)Flash Point, COC, ASTM D92, °F (°C) 203 (95)Viscosity, ASTM D445, cSt at 40°C 55 cSt at 100°C 8.5 ASTM D2161, SUS at 100°F 281 SUS at 210°F 54.8Viscosity Index, ASTM D2270 129Pour Point, ASTM D97, °F (°C) -49 (-45)Appearance, Color PurpleSulfated Ash, ASTM D874, % 0.13Total Base Number, ASTM D2896, mg KOH/g 2.2

D a t e 0 6 / 1 8



M20084

84




M Y S T I K ® J T - 7 ® M U L T I - P U R P O S E G E A R L U B R I C A N T S

M 2 0 0 0 8

Mystik JT-7 Multi-Purpose Gear Lubricants are multi-purpose, thermally stable, sulfur-phosphorus extreme pressure (EP) gear lubricants that exceed the performance requirements of the latest axle and non-synchronized manual transmission. A specially balanced additive provides thermally stable gear lubricants with exceptional durability under high temperature conditions. These are thermally stable and thermally durable gear lubricants. Others lose their EP performance when subjected to thermal stress. Mystik JT-7 Multi-Purpose Gear Lubricants can take the heat and continue to provide superior EP protection, minimum gear wear, excellent deposit control and improved rust and corrosion protection under extreme service conditions. Recommended for all automotive and heavy duty axle service including break-in, add-to or make-up, drain and refill, and for “limited slip” axles. (80W-90)

• Top quality, versatile hypoid EP gear lubricants; recommended in applications that specify API Gear Service GL-4, GL-5 and MT-1 and SAE J2360.

• Superior service in differentials of passenger cars and trucks and heavy duty equipment

• Excellent in limited slip differentials known as Sure-grip®, Posi-trac®, Trac-lock®, etc., for complete fill or for top-off. (80W-90)

• Multiple viscosity grades with high viscosity index. Wide temperature range for all season application in most climates

• Have outstanding thermal stability/durability or long term heat resistance, better than most competitive conventional gear lubricants, thereby providing longer life at higher operating temperatures

• EP additive provides superior wear and scuff protection

MYSTIK® JT-7® MULTI-PURPOSE GEAR LUBRICANTS

Material Code 663705002 663706002

SAE Grade 80W-90 85W-140

AGMA Lubricant Number 4 EP 7 EP Gravity, ASTM D4052, °API 26.5 25.2 Density, lb/gal at 60°F 7.45 7.53 Specific Gravity at 60°F 0.895 0.90 Viscosities: at -12°C, cP – 55,000 at -26°C, cP 90,000 – at 40°C, cSt 146 347 at 100°C, cSt 16.2 28.0 at 100°F, cSt (SUS) 172 (797) 514 (2380) at 210°F, cSt (SUS) 17.4 (87.5) 33.6 (159) Viscosity Index 122 108 Flash Point, ASTM D92, COC, °F (°C) 403 (206) 438 (226) Pour Point, ASTM D97, °F (°C) -27 (-33) 0 (-18) Color Red Red

TYPICAL PROPERTIES:

DESCRIPTION:

FEATURES:

D a t e 0 7 / 1 8



M20008

85

Agric

ultu

ral P

rodu

cts



M Y S T I K ® U N I V E R S A L G E A R L U B R I C A N T

M 2 0 0 1 2

For API Gear Lubricant Service: GL-4 Hypoid EP

Mystik Universal Gear Lubricant contains a Sulfur-Phosphorus (“SP” type) EP additive that provides antiwear and antiscuff lubricity. This product is recommended for gears subject to shock loading in service and for those gear set types requiring “EP” additive compounding because of their design characteristics. A Sulfur-Phosphorus (“SP” type) mild EP additive provides antiwear and antiscuff lubricity for gears subject to shock loading in service and those gear set types requiring “EP” additive compounding because of their design characteristics. • API Service Classification GL-4

• May be used for “add-to” in automotive axles requiring a Hypoid EP lube except those incorporating “limited slip” or “anti-spin” features

• Economically satisfies industrial applications where large loss due to leakage is a factor

MYSTIK® UNIVERSAL GEAR LUBRICANT


SAE Grade 90 AGMA Lubricant Number 4 EP Gravity ASTM D4052, °API 22.9 Density, lb/gal at 60°F 7.6 Specific Gravity at 60°F 0.917 Viscosities: at 40°C, cSt 237 at 100°C, cSt 16.5 at 100°F, cSt (SUS) 275 (1273) at 210°F, cSt (SUS) 17.1 (86.1) Viscosity Index 64 Flash Point, ASTM D92, COC, °F (°C) 430 (221) Pour Point, ASTM D97, °F (°C) -20 (-29) Color Dark Amber

TYPICAL PROPERTIES:

DESCRIPTION:

FEATURES:

D a t e 7 / 1 8



M20012

86




Mystik JT-5 Synthetic Blend TFX tractor fluid is a performance engineered tractor fluid for the equipment owner needing longer component life and ensuring optimum efficiency for many years of tillage and harvesting operations.

• The investment in today’s farm tractors often requires longer ownership of 10 years or more while operating at lowest possible maintenance cost.

• Achieving maximum equipment productivity is required for survival with so many challenges facing modern farm profitability

• Mystik JT-5 Synthetic Blend TFX is recommended for leading tractor manufacturers such as John Deere, New Holland, Kubota and Case/IH MAT 3540 to provide the convenience of one product for improved inventory management for mixed farm fleets while achieving optimum performance.

• Mystik JT-5 Synthetic Blend TFX is designed for modern farm tractors that produce significantly more horsepower requiring greater protection for high production machines that impose much greater stress on transmissions, axles with multiple high output hydraulic applications.


M 2 0 1 0 7

DESCRIPTION:

FEATURES & PERFORMANCE

BENEFITS

D a t e 0 7 / 1 8

ADVANCED TECHNICAL FEATURES PERFORMANCE BENEFIT

Synthetic Blend ✓ Improves performance over wider temperature range and reduces tendency of fluid breakdown due to sustained high operating temperatures

Shear stable viscosity with a high viscosity index

✓ Maintains and sustains optimum viscosity over the service intervals to ensure overall productivity and efficiency

✓ Promotes longer component life of heavily loaded components

✓ Suitable for CVT transmissions that require a stable viscosity through temperature changes and for the life of the oil.

Non-Zinc anti-wear formulation ✓ Provides improved water tolerance that maintains efficiency throughout transmission, hydraulics and brake system

✓ Zinc free formula also reduces impact on environment

Leak resistant-seal maintainer technology

✓ Conditions seals to prevent leakage as equipment ages with higher hours of operation

Special friction modifiers ✓ Improves brake system function and protects against brake chatter

Clean system-detergent/dispersant ✓ Helps minimize tendency for transmission clutch plate glazing from high temperature, deposit build up, protecting against loss of friction control and power transfer efficiency to the drive train.

✓ Maintains high pressure hydraulic system efficiency by preventing hydraulic valve deposit build up and sluggish operation.

Double acting anti-rust/anti-foam technology

✓ Prevents system corrosion and controls tendency for air entrainment resulting in efficient power transfer.

Wide temperature range ✓ Excellent fluidity and start up lubrication that improves system response time in colder temperature operation

Anti-slip formulation ✓ Ensures power transfer efficiency under high loads in transmissions, axles and all hydraulic components


M20107

(Continued)

87

Agric

ultu

ral P

rodu

cts




APPLICATIONS:

D a t e 0 7 / 1 8

MYSTIK® JT-5 SYNTHETIC BLEND TFX


API Gravity, ASTM D4052, °API 31.0Density, lb/gal 7.3Specific Gravity 0.88Viscosities:

at -20°C, cP 3493at -35°C, cP 38200at 40°C, cSt 58.81at 100°C, cSt 9.56

Viscosity Index 146KRL Sheared Viscosity (20hr.) CEC L-45-A-99, cSt 8.2

(Tapered Roller Bearing Shear Test)Tractor FZG ASTM D4998

Weight loss 19mg (Max is 50mg) Flash Point, COC, ASTM D92, °F (°C) 457 (236)Pour Point, ASTM D97, °F (°C) -43 (-45)Water Tolerance (Separation with 5% water) 0.0 4-Ball EP Wear, ASTM D4172, mm 0.36Color Light Amber

TYPICAL PROPERTIES:


M 2 0 1 0 7

RECOMMNED FOR THE FOLLOWING APPLICATIONS• AGCO Power Fluid 821XL• Allison C-4• CASE MS 1205, 1206, 1207, 1209, 1210• CAT TO-2• Denison HF-0, HF-1, HF-2• Eaton Hydraulics• Ford New Holland ESN-M2C134-D• Kubota UDT, Super UDT• API GL-4• Case New Holland: MAT 3540, MAT 3525, MAT 3505• John Deere J20C• Massey Ferguson M-1145• White Q-1826• Volo WB101 • ZF TE-ML-03E, TE-ML-05F, TE-ML-17E, TE-ML-21F

For use in the following OEM equipment: • AGCO • CASE IH • Deutz • Ford • John Deere • Komatsu • Kubota • Massey Ferguson • New Holland •White, and others.


M20107

(Continued)

88





M 2 0 0 1 4

Mystik JT-5 Tractor Trans-Hydraulic Fluid provides excellent performance in modern agricultural equipment. It offers outstanding gear wear protection, brake chatter control and oxidation resistance. Particularly well suited for hard working applications where an added level of protection is desired. Excellent filterability characteristics along with rust and corrosion inhibitors, water tolerance and wide temperature range performance.

• Contains special “friction modifiers” for superior brake chatter control

• Formulated to resist leakage

• Formulated with advanced detergent/dispersant, antiwear, antioxidant, antirust and antifoam additives

• Has proven field performance

Recommended for use in equipment where the following fluids are specified:

• AGCO Power Fluid 821XL

• Allison C-4• CASE MS 1205, 1206, 1207, 1209, 1210

• CAT TO-2

• Denison HF-0, HF-1, HF-2

• Eaton Hydraulics

• Ford New Holland ESN-M2C134-D

• Kubota UDT

• API GL-4

• Case New Holland: MAT 3525

• John Deere J20C

• Massey Ferguson M-1145

• White Q-1826

Suitable for use in the following equipment:

• AGCO

• CASE IH

• KH Deutz

• Ford

• John Deere

• Komatsu

• Kubota

• Massey Ferguson

• New Holland

• Volvo WB101

• White, and others

DESCRIPTION:

FEATURES:

(Continued)

D a t e 0 6 / 1 8

APPLICATIONS:


M20014

89

Agric

ultu

ral P

rodu

cts



M 2 0 0 1 4

D a t e 0 6 / 1 8 - ( C o n t i n u e d )


MYSTIK JT-5 TRACTOR TRANS-HYDRAULIC FLUID

Material Code 663509002 API Gravity, ASTM D4052, °API 31.0 Density, lb/gal 7.3 Specific Gravity 0.88 Viscosities: at -35°C, cP 48,200 at 40°C, cSt 60.3 at 100°C, cSt 9.3 Viscosity Index 130 Flash Point, COC, ASTM D92, °F (°C) 457 (236) Pour Point, ASTM D97, °F (°C) -40 (-40) Falex, ASTM D3233-A, lbs 1,350 4-Ball EP Wear, ASTM D4172, mm 0.38 Color Light Amber

TYPICAL PROPERTIES:



M20014

(Continued)

90




M 2 0 0 2 3

Mystik Multi-Purpose ATF is a multi-function, automatic transmission fluid manufactured from selected high-quality base stocks and premium additives. It protects transmission parts against rust, corrosion, and wear. It is dyed red for leak detection and is engineered to give superior protection and performance. Mystik Multi-Purpose ATF is recommended where the following lubricants are specified: General Motors transmissions calling for DEXRON®-III, DEXRON-IIE and DEXRON-II fluids; Ford transmissions calling for MERCON® type ATF’s; Allison Transmission Division (C-4).

• A single fluid for a wide variety of power transmission uses: automotive automatic transmissions, industrial torque converters, sensitive hydraulic fluid applications, power-shift transmissions, Allison automatic transmissions and power steering fluids.

• Excellent stability for long life service• Anti-wear, anti-leak, anti-foam treated• Detergent inhibitor provides gum-up resistance• Can be used industrially as an excellent multi-viscosity, “all weather” hydraulic fluid, torque converter

fluid and as a cold temperature gear lubricant • Meets the performance requirements of the following hydraulic fluid, power-shift transmission fluid

and automatic transmission fluid specifications:

Vickers M-2950-S and I-286-S GM DEXRON® IIIG/H, IID/E Caterpillar TO-2 Ford MERCON® Allison Type C-3 and C-4 Ford ESP-M2C166H

Recommended for use in automatic transmissions manufactured by General Motors and Ford for model years 2006 and prior (except those calling for FORD Type “F” Fluid, MERCON SP, MERCON V, DEXRON-VI and CVT fluids). Suitable for use in foreign cars and trucks requiring the use of DEXRON-III, DEXRON-IIE, DEXRON-II fluids, and MERCON type ATF’s. Consult owner’s manual for fluid specification.

M Y S T I K ® M U L T I - P U R P O S E A T F

TYPICAL PROPERTIES:

MYSTIK® MULTI-PURPOSE ATF

Material Code 633135002 Gravity, ASTM D4052, °API 33.0Pounds Per Gallon 7.16 Flash Point, ASTM D92, COC, °F (°C) 424 (218) Pour Pont, ASTM D97, °F (°C) -54 (-48) Viscosity, ASTM D445, cSt at 40°C 34.3 cSt at 100°C 6.95 ASTM D2983, cP at -20°C 1,020 cP at -40°C 15,100 Vicosity Index, ASTM D2270 169 Color Red

DESCRIPTION:

FEATURES:

APPLICATIONS:

D a t e 0 6 / 1 8



M20023

91

Agric

ultu

ral P

rodu

cts



NLGI Certified GC-LB

These high temperature Lithium Complex greases combine excellent multi-purpose properties with a high dropping point to give them application over a wide temperature range. Mystik JT-6 Hi-Temp greases exhibit a high Timken OK Load in addition to providing excellent Four-Ball Wear and EP performance. They provide superior protection to lubricate a wide variety of automotive, agricultural, trucking, mining, construction, and industrial equipment. They provide outstanding shock load protection. JT-6 Hi-Temp No. 2 is an extremely versatile performer that is highly recommended for disc brake wheel bearings and is specifically approved for use in Rockwell and Spicer universal joints. This grease provides excellent protection for heavily loaded industrial, mining, and construction applications. JT-6 Hi-Temp No. 1 was developed for applications where service conditions dictate a grease of softer consistency. Both meet the highest performance categories of ASTM D4950 Automotive Grease Classification System, GC for wheel bearing service and LB for chassis service.

• Mystik JT-6 Hi-Temp Greases provide excellent protection in severe service requirements such as disc brake wheel bearings, backhoe hinge pins, and conveyor bearings

• Mining operations, sand/gravel plants, and construction equipment where shock loads are placed on bearings benefit from the use of Mystik JT-6 Hi-Temp Greases


Dana CorporationSpicer Universal/Joint DivisionM-2006-J (#2)Registered NLGI GC-LBWeatherford Artificial Lift (#2)NSF H2 (125250)

M 2 0 0 2 6

(Continued)


DESCRIPTION:

APPLICATIONS:

APPROVALS:

CLASSIFICATION:

D a t e 0 7 / 1 8




M20026

92




MYSTIK® JT-6® HI-TEMP GREASES

Material Code 665003002 665005002 NLGI Consistency Number 1 2 NLGI Certified, ASTM D4950 GC-LB GC-LB Thickener Type Lithium Complex Lithium Complex Texture Smooth, Adhesive Smooth, Adhesive Color Red Red Worked Penetration, ASTM D217 310-340 265-295 Dropping Point, ASTM D2265, °F (°C) 500 (260) 550 (288) Water Washout, ASTM D1264, % loss @ 175°F 9.4 2.5 Rust Prevention, ASTM D1743, rating Pass Pass Copper Corrosion, ASTM D4048, rating 1b 1b Oil Separation, ASTM D1742, % loss 2 1 Timken OK Load, ASTM D2509, lb. 70 80 Four-Ball Wear, ASTM D2266, mm 0.45 0.45 Four-Ball Weld, ASTM D2596, kgf 315 315 Four-Ball Load Wear Index, ASTM D2596, kgf 50 50 Approximate Temperature Range, °F (°C) -10 to 325 -10 to 325 (-23 to 163) (-23 to 163) Base Oil Viscosity: 40°C, cSt 630 630

TYPICAL PROPERTIES:

D a t e 0 7 / 1 8 - ( C o n t i n u e d )

M 2 0 0 2 6





M20026

(Continued)

93

Agric

ultu

ral P

rodu

cts



Mystik JT-6 Multi-Purpose Grease is an exceptionally water resistant product. It is light colored, low staining, and has a very low oil separation rate. Mystik JT-6 Multi-Purpose Grease provides excellent antiseize protection under high loads. Outstanding adhesion enables this product to stay in place better than most other greases. This product is a medium temperature range multi-purpose grease for extreme pressure loads and slow to medium speed bearings. It is excellent for greased chassis points, fifth wheels, and water pumps. It works especially well where extended lubrication intervals are practical, highly loaded or shock loaded grease lubricated applications exist, and excellent rust protection is desired. It is fully rust and oxidation inhibited.

Mystik JT-6 Multi-Purpose is also available in an aerosol form. This product penetrates hard-to-reach points to leave a protective coating of grease. Mystik JT-6 Multi-Purpose Spray Grease has the ability to stay in place and lubricate, even under extreme pressures and severe service. It resists rust, corrosion, oxidation, and wear. This product is ideal for hard to reach points and precise placement. Mystik JT-6 Multi-Purpose Spray Grease dries into a non-fluid consistency in about 15 minutes.

• Exceptionally water resistant - protects against corrosion

• Light colored and low staining

• Very low oil separation rate

• Provides anti-wear and extreme pressure protection

• Excellent adhesion permits it to have better “stay-ability” than most other greases

• A medium temperature range multi-purpose grease for extreme pressure loads, slow to medium speed bearings, greased chassis points, fifth wheels, and water pumps

• Especially good where extended lubrication intervals are practical, highly loaded or shock loaded grease lubricated applications exist, or where excellent rust protection is desired

• Aerosol is excellent for hard to reach locations

DANGER: Extremely flammable aerosol. Please refer to SDS for proper transport, storage and handling. Always check with local jurisdictions for warehouse requirements. Refer to equipment owner’s manual for proper lubricant recommendation.

NOTE: Because this product has better adhesion, it is a little more difficult to pump than less adhesive greases. Use of a follower plate is recommended where air driven pumps are used.

M 2 0 0 2 7

DESCRIPTION:

FEATURES:

APPLICATIONS:


(Continued)

D a t e 0 5 / 1 8


M20027

94




MYSTIK® JT-6® MULTI-PURPOSE GREASE

AEROSOL (Grease)Material Code 665006002 665007002 NLGI Consistency Number 2 2 Thickener Type Anhydrous Calcium Anhydrous Calcium Texture Smooth, Adhesive Smooth, Adhesive Color Medium Amber Medium Amber Worked Penetration, ASTM D217 265-295 265-295 Dropping Point, ASTM D566, °F (°C) 290 (143) 290 (143) Water Washout, ASTM D1264, % loss at 100°F 0.9 0.9 Rust Prevention, ASTM D1743, rating Pass Pass Oil Separation, ASTM D1742, % loss < 1 < 1 Timken OK Load, ASTM D2509, lb. 55 55 Four-Ball Wear, ASTM D2266, mm 0.6 0.6 Four-Ball EP Weld Point, ASTM D2596, kgf 250 250 Four-Ball Last Non-Seizure Load, ASTM D2596, kgf 65 65 Approximate Application Temperature Range, °F (°C) 0 to 250 (-18 to 121) 0 to 250 (-18 to 121)Base Oil Viscosity: 40°C, cSt 1080 —

TYPICAL PROPERTIES:

D a t e 0 5 / 1 8 - ( C o n t i n u e d )

M 2 0 0 2 7





M20027

(Continued)

95

Agric

ultu

ral P

rodu

cts




M 2 0 0 9 8

Mystik JT-6 Super Heavy Duty 460 Grease is an extended service capable, extreme pressure (EP) lubricating grease designed for a wide variety of heavy duty industrial, on highway and off highway equipment applications, especially pins, bushings and anti-friction bearings. Provides extra wear protection when operating with higher loads resulting in longer equipment component life. It is highly recommended for heavily loaded plain and anti-friction bearings such as those found in steel, paper, and cement industries.

Mystik JT-6 Super Heavy Duty 460 Grease is lithium complex thickened grease formulated with a premium additive system and a combination of synthetic and conventional base oils. The optimized formula provides superior performance properties over a wide operating temperature range.

• Proprietary adhesive, stay-in-place formula helps seal out contaminants and extend lubrication intervals

• High load-carrying capacity offers wear protection even under severely loaded conditions• Enhanced water and corrosion resistance protects equipment under adverse conditions including

saltwater spray and exposure to corrosive anti-icing agents• Wide operating range of –5° to 350°F for a variety of weather conditions and application

temperatures

Mystik JT-6 Super Heavy Duty 460 offers superior protection in a variety of applications where enhanced load carrying capability, water resistance, and anti-corrosion protection properties are required such as:

• Heavy Duty and Extreme Heavy Haul Trucking – 5th wheels, U-joints, kingpins, steering drag links, shackle pins, pivots and cross shaft spring pins

• Mining and Construction - bulldozers, scrapers, backhoes, excavators, compactors, cranes, paving machinery, articulated vehicles, soil compactors, graders, ditch hoes, loaders

• Pit and Quarry Equipment – rock crushers, conveyors, rock drills, bridge cranes, water tender, log trucks, chip van trucks

• Agriculture – tractors, implements, tillage, planting and seeding machinery, sprayers and spreaders, hay balers, harvesting machinery, combines, mowers, skid steers

• Heavy Industry – heavily loaded plain and anti-friction bearings in cement, paper, metal (steel, aluminum, copper) industries

• Forestry and Logging – harvester-processor, feller-buncher, mulcher-masticator, brush cutter, shovel logger, skidder, brush piling shovel, brush rake, yarder, log landing machines, shovel, stroke delimber, loader, grinder, chipper, debarker, forest road machines

Mystik JT-6 Super Heavy Duty 460 helps increase equipment life through superior performance including higher load capacity, capable of carrying up to 3X more load than conventional greases. Consult owner’s manual for proper lubricant selection.

DESCRIPTION:

FEATURES:

APPLICATIONS:

(Continued)

D a t e 0 5 / 1 8

3X Performance

Mystik JT-6 Super Heavy Duty

Conventional Grease

0 100 200 300 400 500 600 700 800 900

Four Ball Weld kgfASTM D-2596


M20098

(Continued)

96





D a t e 0 5 / 1 8 - ( C o n t i n u e d )

M 2 0 0 9 8



MYSTIK® JT-6® SUPER HEAVY DUTY 460 GREASE



NLGI Consistency Number 2Thickener Type Lithium ComplexTexture SmoothColor, Observed MagentaWorked Penetration, ASTM D217 265-295Dropping Point, ASTM D2265 °F (°C) 500 (260)Rust Prevention, ASTM D1743, rating Pass5% Synthetic Sea Water Corrosion PassWater Washout, ASTM D1264, % Loss 2.3Water Spray Off, ASTM D4049, % Loss 9.4US Steel Mobility @ 0°F, gpm 38Four-Ball Weld, ASTM D2596, kgf 800Base Oil Viscosity: 40°C, cSt 460

TYPICAL PROPERTIES:




M20098

(Continued)

97

Agric

ultu

ral P

rodu

cts



Premium quality antiwear, antileak, and antifoam hydraulic oils formulated for use in modern high and low pressure industrial and mobile hydraulic systems. They meet the toughest requirements of most manufacturers and are dyed green for ease of identification from other petroleum products. They have 100% paraffinic high VI base oils with low pour points for wide temperature range applicability and additionally are treated with antioxidant stabilizers for long life and an antirust protective additive. A fully synthetic seal swell agent prevents and stops minor leaks and provides longer seal life. They may also be used as API GL-1 gear lubricants where their viscosity is suitable. They have a variety of applications where general purpose non-detergent type oils or rust and oxidation (R&O) inhibited oils are applicable. The High Viscosity Index (HVI) products offer wide temperature application and have a typical dielectric strength of 35kV which makes them suitable for use as non conductive hydraulic fluids. HVI-32 meets FMC Corporation recommendations for a high viscosity index hydraulic fluid.

• Mystik AW/AL Hydraulic Oils meet or exceed: • ASTM D 6158 HM (2005) • General Motors LS-2 (1997)

• Fives Cincinnati P-68, 69, 70 • JMCAS HK P041(2004) • Parker Denison HF-0 (Revision J) • ISO 11158 HM (FDIS 2008) • DIN 51524-2 (2006) • SEB 18 22 (2007) • Eaton Brochure 03-401-2010 • US Steel 126-127-136

• Premium quality antiwear, antileak, and antifoam hydraulic oils

• High viscosity indexes and low pour points for wide temperature usage

• Excellent oxidation resistance and thermal stability

• Manufactured from high quality, solvent refined paraffinic base stocks

• Good water separation characteristics

• Outstanding rust and corrosion inhibition for enhanced service life

• Dyed green for ease of identification

• Highly recommended for: – bearings and gears which require an R&O or R&O/AW hydraulic oil. – hydraulic circuit components (valves, motors, servos, pumps, etc.) – applications where general non-detergent type oils are applicable – vacuum pumps – non conductive hydraulic fluid

NOTE: HVI-32 and HVI-68 are guaranteed to have a dielectric strength of no less than 28 kVwhen packaged. Dielectric strength is extremely sensitive to humidity and contamination. Once the containers are opened, the dielectric strength cannot be expected to remain at its original value. Containers should be kept tightly sealed and stored in a dry environment.

M 2 0 0 3 8

DESCRIPTION:

FEATURES:

(Continued)


D a t e 0 5 / 1 8


M20038

98




M 2 0 0 3 8

TYPICAL PROPERTIES:

D a t e 0 5 / 1 8 - ( C o n t i n u e d )




MYSTIK® AW/AL HYDRAULIC OILS

Material Code 663303002 663304002 663305002 663306002 663312002 663314002

Designation HVI-32 HVI-68 ISO Viscosity Grade 32 46 68 100 32 68 Gravity, °API ASTM D4052 32.3 31.3 30.8 30.1 33.5 31.0 Density, lb/gal at 60°F 7.19 7.24 7.26 7.29 7.14 7.25 Specific Gravity @ 60°F ASTM D1298 0.864 0.870 0.872 0.875 0.857 0.8771 Brookfield Viscosity ASTM D2983 at -18°C, cP – – – – – – at -23.3°C, cP – – – – 1,925 9,100 at -35°C, cP – – – – 16,700 – Viscosity ASTM D445 at 40°C, cSt 32.5 46.0 68.0 98.2 31.6 68.0 at 100°C, cSt 5.55 6.92 9.0 11.5 6.61 10.8 Viscosity Index ASTM D2270 108 106 107 105 172 149 Appearance, Color Green Green Green Green Green Green Flash Point, COC, °F (°C) ASTM D92 435 (224) 435 (224) 468 (242) 471 (244) 417 (214) 453 (234) Pour Point, °F (°C) ASTM D97 -22 (-30) -22 (-30) -11 (-24) +5 (-15) -33 (-36) -27 (-33) Neutralization Number (TAN) ASTM D664 0.5 0.5 0.5 0.5 0.5 0.5 Rust Test, ASTM D665 A - Distilled Water Pass Pass Pass Pass Pass Pass B - Synthetic Sea Water Pass Pass Pass Pass Pass Pass Foam Test, ASTM D892, Sequence I, II, III Pass Pass Pass Pass Pass Pass Oxidation Test, hrs. ASTM D943 5,300 5,200 4,000 3,600 4,200+ 3,500+ Meets Denison HF-0 Requirements Yes Yes Yes Yes Yes Yes Meets Eaton Brochure– 03-401-2010 Yes Yes Yes Yes Yes Yes Dielectric Strength, kV – – – – 35 35


M20038

(Continued)

99

Agric

ultu

ral P

rodu

cts



Mystik AW Hydraulic Oils offer excellent antiwear protection with rust, oxidation, and foam inhibitors in high quality, fully refined base stocks with good oxidation stability. They meet pump performance requirements of major manufacturers like Denison and Eaton.

• Rust, oxidation, antiwear protection, and foam resistance. Blended from high quality, fully refined base oils.

Mystik AW Hydraulic Oils meet or exceed: • ASTM D 6158 HM (2005) • General Motors LS-2 (1997) • Fives Cincinnatti P-68, 69, 70 • JCMAS HK P041 (2004) • Parker Denison HF-0 (Revision J) • ISO 11158 HM (FDIS 2008) • DIN 51524-2 (2006) • SEB 181 222 (2007) • Eaton Brochure 03-401-2010 • US Steel 126, 127, 136

• High and low pressure hydraulic systems where additive-treated product is required.

• Vane, piston, and gear pumps.

• Bearings, gears, and pumps which require an R&O or R&O/AW hydraulic oil.

MYSTIK® AW HYDRAULIC OILS

Material Code 663380002 663381002 663382002 663383002 ISO Viscosity Grade 22 32 46 68 API Gravity at 60°F ASTM D4052 33.7 32.6 31.2 30.8 Pounds/Galon at 60°F 7.13 7.18 7.24 7.26 Specific Gravity at 60°F ASTM D1298 0.856 0.862 0.870 0.872 Viscosity ASTM D445 at 40°C, cSt 22.3 32.3 46.6 68.0 at 100°C, cSt 4.45 5.59 6.96 9.0 Viscosity Index ASTM D2270 110 111 106 107 Flash Point, COC, °F (°C) ASTM D92 399 (204) 415 (213) 425 (218) 465 (241) Pour Point, °F (°C) ASTM D97 -40 (-40) -27 (-33) -22 (-30) -17 (-27) Color, ASTM D1500 L0.5 0.5 0.5 0.5

TYPICAL PROPERTIES:

M Y S T I K ® A W H Y D R A U L I C O I L S

M 2 0 0 7 0

DESCRIPTION:

FEATURES:

APPLICATIONS:

D a t e 0 5 / 1 8



M20070

100




Mystik Hydraulic Jack Oil is a low viscosity fluid providing extra low friction in hand or foot operated hydraulic systems.

• Treated with antirust, antiwear, antioxidant, and antifoam additives

• Low viscosity reduces pumping effort required and allows jack to close rapidly and completely when released

• Provides rust, wear, and oxidation protection and foam resistance. Contains low wax content, low aniline point oils to give seal swell and softening to retard leakage and provide a naturally low pour point.

• May be used at sub-zero temperatures in motorized hydraulic systems

• Can also serve as a high speed spindle oil and as a low temperature lubricant

• Easy to use package with pour spout

M 2 0 0 6 7

MYSTIK® HYDRAULIC JACK OIL

Material Code 663321002 ISO Grade (Approx.) 22 Gravity, °API @ 60°F ASTM D4052 25 Density, lb/gal at 60°F 7.53 Specific Gravity at 60°F ASTM D1298 0.9042 Viscosity ASTM D445 at 40°C, cSt 21.5 at 100°C, cSt 3.8 Viscosity Index ASTM D2270 32 Flash Point, COC, °F (°C) ASTM D97 315 (157) Pour Point, °F (°C) ASTM D97 -50 (-46) Color Red

TYPICAL PROPERTIES:

M Y S T I K ® H Y D R A U L I C J A C K O I L

DESCRIPTION:

FEATURES:

D a t e 0 6 / 1 8



M20067

101

Agric

ultu

ral P

rodu

cts



Mystik TerraSyn Irrigation Engine Oil is an SAE 15W-40 synthetic stationary natural gas engine oil. It is specially formulated to provide lubrication in engines that have been converted to natural gas fuel, such as those in LP and agricultural irrigation pump service. Designed for added engine valve train anti-wear protection.

Mystik TerraSyn Irrigation Engine Oil provides:

• Improved engine top end start up lubrication, especially in colder environments • Enhanced valve train protection compared to conventional stationary natural gas engine oils • Excellent extended drain capability, providing user savings in downtime, work man-hours and

oil usage

MYSTIK® TERRASYNTM IRRIGATION ENGINE OIL

Material Code 663061002 SAE Grade 15W-40Gravity, ASTM D4052, °API 31.6Density, lbs/gal 7.22Flash Point, ASTM D92 (COC), °F (°C) 489 (254)Viscosity, ASTM D445, cSt at 40°C 107cSt at 100°C 15.1Viscosity Index, ASTM D2270 147CCS Viscosity, ASTM D5293, cP -20C 5,340 -25C 9,300MRV Viscosity, ASTM D4684, cP -25C 10,700Pour Point, ASTM D97, °F (°C) -60 (-51)Color, ASTM D1500 6.0Sulfated Ash, ASTM D874, m% 0.45TBN, ASTM D2896 5.0Zinc, ppm 900

TYPICAL PROPERTIES:

M 2 0 1 0 0

DESCRIPTION:

D a t e 0 6 / 1 8

M Y S T I K ® T E R R A S Y N T M I R R I G A T I O N E N G I N E O I L

Mystik is a registered trademark and TerraSyn is a trademark of CITGO Petroleum Corporation. All other registered trademarks or trademarks are the property of their respective owners.


M20100

102




Mystik Bar and Chain Lubricant is a great choice for loggers as well as home and ranch users. It utilizes special components to reduce wear, guard against rust and enhance metal adhesion to reduce spatter.

Designed for use over a wide temperature range. For use in all brands of chain saws.

• Lubricates and Cools Chain

• Polymer Controls Spatter

• Guards Against Rust

• Provides Wear Protection

NOTE: NOT FOR USE IN ENGINES! Use Mystik JT-4® 2-Cycle Lawn and Garden Engine Oil, Material Code 663091002, where 2-cycle engine oil is specified.

MYSTIK® BAR AND CHAIN LUBRICANT

Material Code 663605002 SAE Grade 30 ISO Viscosity Grade 100 Gravity, °API ASTM D4052 30 Pounds/Gallon @ 60°F 7.3 Flash Point, COC, °F (°C) ASTM D92 340 (171) Pour Point, °F (°C) ASTM D97 -23 (-10) Viscosity ASTM D445 cSt at 40°C 82 cSt at 100°C, 10 Appearance, Color Blue-Green

TYPICAL PROPERTIES:

M Y S T I K ® B A R A N D C H A I N L U B R I C A N T

M 2 0 0 4 8

DESCRIPTION:

FEATURES:

D a t e 0 5 / 1 8



M20048

103

Agric

ultu

ral P

rodu

cts



Mystik Turbine Drip Oil is formulated with highly refined lubricating base oils and inhibited with a foam suppressant. It is for use in dripper lubrication systems for irrigation water well line shaft bearings where a food grade registered product is NOT required. NOTE: This lubricant is not recommended for use where a food grade quality lubricant is required. This product should not be used for potable water well pump lubrication. It is the user’s responsibility to ensure proper selection of lubricating oil for agricultural irrigation and related systems; refer to applicable regulatory agency requirements.

MYSTIK® TURBINE DRIP OIL

Material Code 663435002 SAE Grade 10W ISO Grade 32 Gravity, °API ASTM D4058 24.8 Density, lb/gal at 60°F 7.54 Specific Gravity @ 60°FASTM D1298 0.9053 Viscosity, Brookfield @ -25°C, cP ASTM D2893 6400 Viscosity ASTM D445 at 40°C, cSt 29.3 at 100°C, cSt 5.0 at 100°F, cSt (SUS) 150 at 210°F, cSt (SUS) 42.4 Viscosity Index ASTM D2270 86 Flash Point, COC, °F (°C) ASTM D92 380 (193) Pour Point, °F (°C) ASTM D97 -25 (-32) Color, ASTM D1500 3.0

TYPICAL PROPERTIES:

M Y S T I K ® T U R B I N E D R I P O I L

M 2 0 0 5 7

DESCRIPTION:

FEATURES:

D a t e 0 5 / 1 8



M20057

104




Mystik Non-Detergent General Purpose Oils are designed for use in non-critical applications where a general purpose oil is desired. This includes low pressure hydraulic systems such as hydraulic jacks and air compressors requiring a non-detergent type lubricant. They are available in SAE 10W, 20W-20, and 30 viscosity grades. Mystik Non-Detergent General Purpose Oils are not recommended for use in gasoline or diesel engines.

MYSTIK® NON-DETERGENT GENERAL PURPOSE OILS

Material Code 663111002 663112002 663113002

SAE Grade 10W 20W-20 30ISO Grade (Approx.) 32 68 100Density, lb/gal at 60°F (Approx.) 7.54 7.6 7.65Viscosities (Approx.): at 100°C, cSt 5.0 8.0 11 at 40°C, cSt 29 62 119 at 210°F, SUS 44 54 — at 100°F, SUS 165 340 —Viscosity Index 95 95 95Flash Point, ASTM D92, °F (°C) 380 (193) 395 (202) 425 (218)Pour Point, ASTM D97, °F (°C) -25 (-32) -10 (-23) -5 (-20)

TYPICAL PROPERTIES:

NOTE: Consult machinery operator’s manual for proper viscosity grade. For gasoline or diesel engines, consider Mystik JT-8 engine oils.

M Y S T I K ® N O N - D E T E R G E N T G E N E R A L P U R P O S E O I L S

M 2 0 0 9 0

DESCRIPTION:

D a t e 0 5 / 1 8

Mystik is a registered trademark of CITGO Petroleum Corporation.



M20090

105

Agric

ultu

ral P

rodu

cts



M Y S T I K ® L U B R I C A N T S T E N A X ® F L U I D S

M 2 0 0 1 7

Meets The Requirements of Caterpillar TO-4 And Allison C-4

Manufacturers of heavy duty equipment are continually upgrading their machines and components. Significant improvements in transmissions and final drives have increased equipment durability and productivity, but have also increased the workload on gears and bearings, and required the development of new and diverse friction materials. The use of the correct lubricant to support these new designs is critical.

Mystik Lubricants Tenax Fluids are heavy duty transmission and final drive lubricants formulated to meet the performance requirements of Caterpillar TO-4 (10W, 30, & 50) and Allison C-4 (10W & 30). They provide the protective qualities essential to maximize equipment life and performance.

• Meets the performance requirements of Caterpillar TO-4

• The SAE 10 and SAE 30 meet the Allison C-4 specification

• Recommended for use in heavy duty powershift transmissions, final drives, hydrostatic transmissions, torque converters and hydraulics where a TO-4 or C-4 fluid is recommended. These products are not recommended as engine lubricants.

• SAE 50 can be used in Eaton/Fuller, Rockwell and Dana/Spicer transmissions for service-fill

• Excellent performance in ZF powershift transmissions used in off-road machines, special vehicles and lift trucks

MYSTIK® LUBRICANTS TENAX® FLUIDS

Material Code 663510002 663511002 663512002 SAE Grade 10W 30 50 Gravity, ASTM D4052, °API 31.1 31.0 27.3 Density, lb/gal 7.3 7.4 7.4 Specific Gravity 0.877 0.886 0.896 Viscosity: at -35°C, cP 23,000 - - at 40°C, cSt 38.1 96 209.4 at 100°C, cSt 6.1 11.3 17.9 Viscosity Index 112 104 100 Flash Point, ASTM D92, COC, °F (°C) 420 (216) 446 (230) 511 (266) Pour Point, ASTM D97, °F (°C) -38 (-39) -27 (-33) 0 (-18) Color, ASTM D1500 L3.0 3.5 4.0

TYPICAL PROPERTIES:

DESCRIPTION:

FEATURES:

APPLICATIONS:

D a t e 0 6 / 1 8



M20017

References

106106

SAE J306 — AUTOMOTIVE GEAR LUBRICANT VISCOSITY CLASSIFICATION

SAE Viscosity Grade s Maximum Temperature for a Viscosity of 150 000 cP, °C(1,2)

Kinematic Viscosity at 100°C, cSt(3) Minimum(4)

Kinematic Viscosity at 100°C, cSt(3) Maximum

70W -55(5) 4.1 —

75W -40 4.1 —

80W -26 7.0 —

85W -12 11.0 —

80 — 7.0 <11.0

85 — 11.0 <13.5

90 — 13.5 <18.5

110 — 18.5 <24.0

140 — 24.0 <32.5

190 — 32.5 <41.0

250 — 41.0 —

NOTE—1cP = 1 mPa•s; 1 cSt = 1mm2/s1. Using ASTM D 2983.2. Additional low-temperature viscosity requirements may be appropriate for fluids intended for use in light duty synchronized manual

transmissions. See text.3. Using ASTM D 445.4. Limit must also be met after testing in CEC L-45-A-99. Method C (20 hours.)5. The precision of ATSM Method D2983 has not been established for determinations made at temperatures below -40°C. This fact

should be taken into consideration in any producer-consumer relationship.

*SAE J2360 replaced MIL-PRF-2105E as a world-wide standard for Automotive Gear Lubricants for Commercial and Military use. The gear lubricant shall meet the limits for classification described in SAE J306.

SAE J300 — SAE VISCOSITY GRADES FOR ENGINE OILS

SAE Viscosity Grade

Low-Tempurature Cranking

Viscosity(3) (mPa•s) Max

Low-Tempurature (°C) Pumping

Viscosity(4) (mPa•s) Max with No Yield

Stress

Low-Shear-Rate Kinematic

Viscosity(5) (mm2/s) at 100°C Min

Low-Shear-Rate Kinematic

Viscosity(5) (mm2/s) at 100°C Max

High-Shear-Rate Kinematic

Viscosity(5) (mPa•s) at 100°C Min

0W 6200 at -35 60 000 at -40 3.8 — —

5W 6600 at -30 60 000 at -35 3.8 — —

10W 7000 at -25 60 000 at -30 4.1 — —

15W 7000 at -20 60 000 at -25 5.6 — —

20W 9500 at -15 60 000 at -20 5.6 — —

25W 13 000 at -10 60 000 at -15 9.3 — —

8 — — 4.0 <6.1 1.7

12 — — 5.0 <7.1 2.0

16 — — 6.1 <8.2 2.3

20 — — 6.9 <9.3 2.6

30 — — 9.3 <12.5 2.9

40 — — 12.5 <16.3 3.5 (0W-40 and 10W-40 grades)

40 — — 12.5 <16.3 3.7 (15W-40, 20W-40 and 25W-40, 40

grades)

50 — — 16.3 <21.9 3.7

60 — — 21.9 <26.1 3.7

Notes — 1 mPa•s = 1 cP; mm2/s = 1 cSt1. All values, with the exception of the low-tempurature cranking viscosity, are critical specifications as defined by ASTM D3244 (see text,

Section 7.)2. ASTM D5293: Cranking viscosity — The non-critical specification protocol in ASTDM D3244 shall be applied with a P value of 0.95.3. ASTM D4684: Note that the presence of any yield stress detectable by this method constitutes a failure regardless of viscosity.4. ASTM D4455. ASTM D4683, ASTM D4741, ASTM D5481, or CEC L-36-90.

References

106106

Refe

renc

es

107107

References

108108

+ Suitable ++ Recommended

Mystik Grease Characteristics Chart

NLG

I G

rade

Bas

e O

il T

ype

(Min

eral

, S

ynth

etic

or

Ble

nd)

EP

/AW

(E

nhan

ced

Load

C

arry

ing)

Wat

er

Res

ista

nce

Rus

t P

rote

ctio

n

Sal

twat

er

Rus

t P

rote

ctio

n

Low

T

empe

ratu

res

Hig

h T

empe

ratu

res

Centra-Lube Grease 0-00 Min. + + + +

General Purpose Grease 2 Min. + + +

JT-6 High Performance Marine Grease 2 Min. + + + ++

JT-6 Hi-Temp Greases 1 Min. ++ + + + +

1½ Min. ++ + + +

2 Min. ++ + + +

JT-6 Hi-Temp Grease with Moly 2 Min. ++ + + +

JT-6 Synthetic Hi-Temp Greases (ISO 100)

1 Syn. ++ + ++ ++ ++ ++

2 Syn. ++ + ++ ++ ++ ++

JT-6 Synthetic Hi-Temp Grease (ISO 220)

2 Syn. ++ + ++ ++ ++ ++

JT-6 Lo-Temp Extreme Grease 2 Min. ++ + + ++

JT-6 Multi-Purpose Grease 2 Min. + + +

JT-6 Super Heavy Duty 460 Grease 2 Blend ++ ++ + ++ +

JT-6 Synthetic Blend Grease 2 Blend ++ + + ++ +

Moly Grease 2½ Min. ++ + + +

OG-5 Outside Gear Grease 1½ Min. ++ +

Red Lithium C 2 Min. + +

Refe

renc

es

109109

574-544000

0 034-0040

583-5530

043-0131

592-5622

052-0223

502-5714

061-0315

6 85-115

dekroW MTSAIGLN)°5.0±C°52(°1±F°77 ta noitartenePrebmuN

NLGI GREASE CLASSIFICATIONS

The following table shows the worked penetration values for the various NLGI grades of grease.

ASTM D4950 STANDARD CLASSIFICATION AND SPECIFICATIONSFOR AUTOMOTIVE SERVICE GREASES

Service Category ‘‘L’’ Chassis Grease

LB –

Service Category ‘‘G’’ Wheel Bearing Grease

GC – Lubricate wheel bearings over a wide temperature range. Temperatures from -40°F with frequent excursions to 320°F and occasional to 392°F.

Chassis and universal joints subject to water contamination and heavy loads. Usable temperature -40°F to 248°Fwith relubrication intervals greater than 2000 miles.


LUBRICANT

GC-LB

®

LB

AUTOMOTIVECHASSIS

LUBRICANT

®

References

110110

Gen

eral

Gui

de -

Exce

ptio

ns A

re P

ossi

ble

Aluminum Complex

Calcium Stea

rate

Calcium 12

-Hyd

roxy

Calcium Complex

Calcium Sulfo

nate

ClayLith

ium Stearat

e

Lithium 12

-Hyd

roxy

Lithium Complex

Polyurea

Sodium Soap

Alu

min

um C

ompl

exC

IB

II

II

II

I*I

Cal

cium

Ste

arat

eI

CC

IB

IC

BC

I*I

Cal

cium

12-

Hyd

roxy

BC

CB

CI

CC

CI*

IC

alci

um C

ompl

exI

IB

CI

II

IB

CI

Cal

cium

Sul

fona

teI

BC

IC

II

BB

II

Cla

yI

II

II

CI

II

II

Lith

ium

Ste

arat

eI

CC

II

IC

CC

I*I

Lith

ium

12-

Hyd

roxy

IB

CI

BI

CC

CI*

ILi

thiu

m C

ompl

exI

CC

BB

IC

CC

I*I

Poly

urea

I*I*

I*C

II

I*I*

I*C

ISo

dium

Soa

pI

II

II

II

II

IC

C -

Com

patib

leB

- B

orde

rline

I - In

com

patib

leI*

- Dep

ende

nt U

pon

Type

Refe

renc

es

111111

1800

ASTM ISOINDUSTRIAL

OILS

AGMAGEAROILS

SAEGEAROILS

SUS/100ºF

SUS/210ºF

SAECRANKCASE

OILS

SAYBOLTVISCOSITIES APPROX.

cSt100ºC

cSt40ºC

8000

60005000

4000

3000

2000

1500

1000

1400

1000800

600

400

300

800

600500

400

300

200

150

200

140

100

100

100

200

300

80

8090

80

60

60

70

60

70

60

40

70

50

40

45

50

55

40

50

40

35

30

30

20

20

14

15

10

10

8

8

6

6

5

4

4

3

3

2

2

1500

1000

680

460

320

220

250

140

150

100

68

90 50

60

40

30

20

16

85W

80W

75W

10W5W, 0W

15W

46

32

22

15

10

1

2

3

4

5

6

7

8

8A

5

7

3

2

Approximate Equivalence of Viscosity Grading Systems

Viscosities can be relatedhorizontally only. Viscositiesbased on 95 VI single grade oils.ISO are specified at 40ºC.AGMA are specified at 100ºF.SAE 75W, 80W, 85W, 5W and 10Wspecified at low temperature.Equivalent viscosities for 100ºand 210ºF are shown.

140319

Index

112112

PRODUCT INDEX

Index

112112

Mystik® Ammonia Compressor Oil 68 . . . . . . . . . . . . . . . . 72

Mystik® Anti-Leak Industrial Oil . . . . . . . . . . . . . . . . . . . . . 56

Mystik® AW Hydraulic Oils . . . . . . . . . . . . . . . . . . . . . . . . . 57

Mystik® AW/AL Hydraulic Oils . . . . . . . . . . . . . . . . . . . 58-59

Mystik® Bar and Chain Lubricant . . . . . . . . . . . . . . . . . . . . 65

Mystik® Centra-Lube™ Grease . . . . . . . . . . . . . . . . . . . . . 38

Mystik® General Purpose Grease . . . . . . . . . . . . . . . . . . . 39

Mystik® Hydraulic Jack Oil . . . . . . . . . . . . . . . . . . . . . . . . . 59

Mystik® JT-4® 2-Cycle Lawn and Garden Engine Oil . . . . . 10

Mystik® JT-4® 2-Cycle Premium Outboard Engine Oil . . . . 11

Mystik® JT-4® 2-Cycle Premium Plus Outboard

Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Mystik® JT-4® 4-Cycle Marine Engine Oils . . . . . . . . . . . . . 17

Mystik® JT-4® All-In-One Outboard Engine Oil . . . . . . . . . . 13

Mystik® JT-4® Premium High Performance Lower Unit

Gear Lubricant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Mystik® JT-4® Sea & Snow® 2-Cycle Engine Oil . . . . . . . . . 14

Mystik® JT-4® Synthetic 2-Cycle Personal Watercraft

Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Mystik® JT-4® Synthetic 2-Cycle Snowmobile Engine Oil . . 16

Mystik® JT-4® Synthetic 4-Cycle All-Terrain Vehicle

Motor Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Mystik® JT-4® Synthetic 4-Cycle Snowmobile Motor Oil

SAE 10W-40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Mystik® JT-5® Synthetic Blend TFX *NEW* . . . . . . . . . 29-30

Mystik® JT-5® Tractor Trans-Hydraulic Fluid . . . . . . . . . 31-32

Mystik® JT-6® Hi-Temp Grease with Moly . . . . . . . . . . . . . . 43

Mystik® JT-6® Hi-Temp Greases . . . . . . . . . . . . . . . . . . 41-42

Mystik® JT-6® High Performance Marine Grease . . . . . . . . 39

Mystik® JT-6® Lo-Temp Extreme Grease . . . . . . . . . . . . . . 45

Mystik® JT-6® Multi-Purpose Grease . . . . . . . . . . . . . . 47-49

Mystik® JT-6® Super Heavy Duty 460 Grease . . . . . . . 49-50

Mystik® JT-6® Synthetic Blend Grease . . . . . . . . . . . . . 51-52

Mystik® JT-7® Synthetic Hi-Temp Greases . . . . . . . . . . 44-45

Mystik® JT-7® Extended Range Full Synthetic

Gear Lubricant SAE 75W-140 . . . . . . . . . . . . . . . . . 21-22

Mystik® JT-7® Multi-Purpose Gear Lubricants . . . . . . . . . . 23

Mystik® JT-7® Synthetic Blend SAE 75W-90

Gear Lubricant . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25

Mystik® JT-8® Premium Gasoline Motor Oils . . . . . . . . . . . . 1

Mystik® JT-8® Premium Gasoline Synthetic Motor Oils . . 2-3

Mystik® JT-8® Synthetic Blend Super Heavy Duty

Engine Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8


Engine Oils Monogrades. . . . . . . . . . . . . . . . . . . . . . . . . 6


Engine Oils SAE 10W-40 and SAE 15W-50 . . . . . . . . . 9

Mystik® JT-8® Synthetic Engine Oil 5W-40 . . . . . . . . . . . . 4-5

Mystik® Lubricants Tenax® Fluids . . . . . . . . . . . . . . . . . . . . 36

Mystik® Moly Grease. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Mystik® Multi-Purpose ATF . . . . . . . . . . . . . . . . . . . . . . . . . 33

Mystik® Non-Detergent General Purpose Oils . . . . . . . . . . 71

Mystik® OG-5 Outside Gear Grease . . . . . . . . . . . . . . . . . 54

Mystik® Red Lithium C . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Mystik® Rock Drill Oil 150 . . . . . . . . . . . . . . . . . . . . . . . . . 66

Mystik® SX-7000® Synthetic Fluids . . . . . . . . . . . . . . . 26-27

Mystik® Synthetic Blend Multi-Vehicle ATF . . . . . . . . . . 34-35

Mystik® Terra® 340 Gas Engine Oils . . . . . . . . . . . . . . . . . 61

Mystik® Terra® 500 Gas Engine Oils . . . . . . . . . . . . . . . . . 62

Mystik® Terra® Free Ashless Gas Engine Oils . . . . . . . . . . 63

Mystik® TerraSynTM Irrigation Engine Oil . . . . . . . . . . . . . . 64

Mystik® Tuff-Torq EG® . . . . . . . . . . . . . . . . . . . . . . . . . . 67-68

Mystik® Turbine Drip Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Mystik® Twin Disc Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Mystik® Universal Gear Lubricants . . . . . . . . . . . . . . . . . . 28

Mystik® ViscidLube® Oil Treatment . . . . . . . . . . . . . . . . . . . 70

113

Engine Oils

114114

2

Mystik LubricantsP.O. Box 4689Houston, TX 77210800-248-4684

www.mystiklubes.com

© 2018 Mystik Lubricants. All rights reserved. The Mystik name, logo, trade dress and all related marks are registered trademarks protected by federal law.

LM180117-001

Documents

N EW ! A gricultural P roducts Automotive, Commercial ... · Product Guide 2018 LU B R IC AN TS N EW ! A gricultural P roducts G uide *' $ J 1 MF B TF WJTJU X X X X X X N Z T UJL