MVN-7001H - REV B - MobileView · x.xxx = ± .005 interpret dimensions and tolerances per asme y14.5m-2009 date rev 2016/4/29 third angle projection drawn by 2016/4/29 jb. p7 p6 p4

256

248

194

290

42.50 42.5 163 MOUNTING HOLES: 4X DIA 0.20 INCH

7.6 X 6.4 INCH PATTERN

205

102.3

NOTES:ORDERING INFORMATION:1.

2. OPERATION:THIS ASSEMBLY IS USED WITHIN A MOBILEVIEW SYSTEM

3. SPECIFICATIONS:OPERATING TEMPERATURE: -20 TO 55C (-4F TO +131F) @10-90% RHVOLTAGE OP SPEC: 9-32VDCPOWER: 30WOUTPUT VOLTAGE: 12VDC @ 2A, 5VDC @ 2AWEIGHT: ~15LBS

4. DIMENSIONS SHOWN ARE: (mm) 102 (HEIGHT) X 194 (WIDTH) X 256 (DEPTH)5. INSTALLATION:

MOUNTING SURFACE MUST BE FLAT AND SECURED AGAINST EXCESS MOVEMENT AND AMPLIFIED VIBRATION

REVISIONS

REV DESCRIPTION DATE

A INITIAL DEVELOPMENT 2016/04/29

B UPDATED ORDERING INFORMATION TABLE 2016/11/28

PART ID DESCRIPTION

MVN-7300H-F1-K1 7001H, 16 CH HYBRID NVR, HARNESS, CONNECTION KIT

MVN-7300H-F1-01 7001H, 16CH HYBRID NVR, NO HARNESS OR MEDIA

MVN-4037-00-P1A 7001H, J1 POWER HARNESS, 15 INCH LENGTH

MVN-4037-00-P2A RS485 SERIAL PORT HARNESS, 15 INCH LENGTH

MVN-4037-40-00 4 CH ANALOG VIDEO HARNESS, 15 INCH LENGTH

MVN-4039H-F0-00 HYBRID HARNESS CONNECTION KIT, 16 ANALOG

MVA-4039-IH-01F INTERCONNECT HARNESS, 2PIN TO 3PIN MOLEX, QTY 16

D

C

B

A

B

C

D

4 3 2

UTC PROPRIETARYTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF UNITED TECHNOLOGIES CORPORATION. ANY REPRODUCTION IN WHOLE OR IN PART WITHOUT THE PRIOR WRITTEN PERMISSION OF UNITED TECHNOLOGIES CORPORATION IS PROHIBITED. C 2015 UNITED TECHNOLOGIES CORPORATION. ALL RIGHTS RESERVED.

1

A

34 2 1

SIZE

TITLE

1 OF 101:1.5SCALE SHEET

DWG NOMVN-7001HB

MOBILEVIEW 7001H NVR

B

UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES

ANG MACH = ± 1.0 BEND = ± 3.0 X.XX = ± .02

X.XXX = ± .005

INTERPRET DIMENSIONS AND TOLERANCES PER ASME Y14.5M-2009

REVDATE

2016/4/29

THIRD ANGLE PROJECTION

DRAWN BY 2016/4/29

JB

P4 P3 P2A P1AP6P7

GPS

WIFI

A

REAR VGA

B

P7 P8

P1AP2AP4 P3

CH1~4 CH5~8 CH9~12 CH13~16

ALARM EXT.10

RS232 RS485AV OUTPOWER

REVISIONS



ITEM DESCRIPTIONP1A CONNECTOR MULTI-PIN AVIATION CONNECTOR FOR POWER AND IGNITIONP2A CONNECTOR MULTI-PIN AVIATION CONNECTOR FOR RS485, 12V OUT, REPLACES P2 ON 7001P3 CONNECTOR MULTI-PIN AVIATION CONNECTOR FOR RS232, 12V&5V OUTP4 CONNECTOR MULTI-PIN AVIATION CONNECTOR FOR AV & 12V POWER OUT (1A)P6&P7 CONNECTOR MULTI-PIN MOLEX CONNECTOR FOR DIGITAL &ANALOG INPUTS, RELAY OUTPUTS, REMOTE

STATUS INDICATORS AND 12V 7 5V OUTANALOG CHANNEL CONNECTORS (X4)

FOUR MULTI-PINBLOCK CONNECTOR WITH POSITIVE LOCKING LATCH. EACH CONNECTOR SUPPORTS FOUR (4) VIDEO AUDIO INPUT CHANNELS + POWER

REAR ETHERNET PORT FOR THE CONNECTION OF IP & OTHER NETWORK DEVICESVGA 15-PIN DSUB CONNECTOR FOR THE CONNECTION OF A VGA MONITORGPS SMA CONNECTOR FOR THE CONNECTION OF GPS ANTENNA CABLE

D

C

B

A

B

C

D

4 3 2


1

A

34 2 1

SIZE

TITLE

2 OF 102:1SCALE SHEET

DWG NOMVN-7001HB B


ANG MACH = ± 1.0 BEND = ± 3.0 X.XX = ± .02

X.XXX = ± .005


REVDATE

2016/4/29


DRAWN BY 2016/4/29

JB

NOTES:ALL MATERIAL MUST BE RoHS COMPLIANT;1.PROCESS CONFORMS TO IPC620 STANDARD 2;2.1PC ATS FUSE SHIPMENT AS ATTACHMENTS;3.

P1A

265

1

87 43

REVISIONS



ITEM DESCRIPTION QTY MPN

1 RAW CABLE,UL1007,16AWG,RED/BLACK/WHITE

2 PLUG,M16-6S,6PIN,MALE 1PCS ZHONGQIANG 16M-6A

3 TERMINAL,MALE,PITCH:4.2mm,24-18AWG,OR EQUAL 6PCS MOLEX 0039000061

4 HOUSING,PLUG,PITCH:4.2mm,2x3PIN,NYLON,UL94V2,-40 85 C OR EQUAL 1PCS MOLEX 0039012061

5 ATS FUSE,12A,FAST BLOW 2PCS

6 SMALL IN-LINE FUSEHOLDER,SL-709J,(#18) 1PCS

7 MARKER CABLE TIE,GTK-100M 1PCS

8 LABEL,L:23mmx7mm,METALIZED POLYESTER,BLACK ON SILVER 1PCS

P1A COLOR PROTECTION A SIGNAL

1 RED ATS FUSED 1 DCIN+2 RED 43 BLACK 2 IGN-4

DCIN-5 BLACK 5

6 WHITE 6 IGN+3

D

C

B

A

B

C

D

4 3 2


1

A

34 2 1

SIZE

TITLE


DWG NOMVN-7001HB B


ANG MACH = ± 1.0 BEND = ± 3.0 X.XX = ± .02

X.XXX = ± .005


REVDATE

2016/4/29


DRAWN BY 2016/4/29

JB

NOTES:ALL MATERIAL MUST BE RoHS COMPLIANT;1.PROCESS CONFORMS TO IPC620 STANDARD 2;2.

WIRE LIST:

REVISIONS




1 CABLE,UL2464,22AWGx2C+22AWGx2P,300V,80C,BLACK,VW-1

2 PLUG,M12-6S,6PIN,FEMALE 1PCS ZHONGQIANG 12M-6A

3 TERMINAL,PITCH:4.2mm,MALE,BRASS,24-18AWG,TINNED 6PCS MOLEX 39-00-0040

4 HOUSING,PITCH:4.2mm, PLUG,2x4PIN,PA66,UL94V-0,-25 85 C, NATURAL 1PCS MOLEX 46993-0810

X1 WIRE COLOR X2 SIGNAL WIRE AWG1 WHITE 1 TX485+

22AWG2 GREEN 2 TX485-5 ORANGE 3 RX485+6 YELLOW 4 RX485-3 RED 7 12VDC 22AWG4 BLACK 8 GND

D

C

B

A

B

C

D

4 3 2


1

A

34 2 1

SIZE

TITLE


DWG NOMVN-7001HB B


ANG MACH = ± 1.0 BEND = ± 3.0 X.XX = ± .02

X.XXX = ± .005


REVDATE

2016/4/29


DRAWN BY 2016/4/29

JB

10

30

10

50

NOTES:ALL MATERIAL MUST BE RoHS COMPLIANT;1.PROCESS CONFORMS TO THE IPC620 STANDARD 2;2.VIDEO AND AUDIO USE THE 22AWG WIRE, POWER USE 20AWG WIRE;3.THE SHEILD SOLDERED WITH BNC SHELL, OTHERS SHOULD BE DOUBLE CRIMP WITH TERMINAL;4.

5 6

4

PVC 45P RED

PVC 45P WHITE

PVC 45P BLUE

PVC 45P YELLOW

1

PVC 45P BLACK2 3

WIRE LIST:

VIDEO1

VIDEO1

AUDIO1

AUDIO1

REVISIONS




1 CABLE,UL2725 (22AWGx1C+S)+22AWGx1C+20AWGx2C+ADB,VW-1,BLACK

2 TERMINAL,0.025 STYLE,FEMALE,COPPER ALLOY TINNED,24-20AWG 16PCS TE 1123343-1

3 HOUSING,0.025 STYLE,PITCH:2.2mm,16P,24-20AWG,BLACK 1PC TE 1318386-2

4 BNC,FEMALE,75Ω,PIN:G1U"MIN,SHELL:NI 4PC

5 TERMINAL,PITCH:4.2mm,MALE,BRASS,24-18AWG,TINNED 12PCS MOLEX 39-00-0040

6 HOUSING,PITCH:4.2mm,PLUG,1x3PIN,PA66,UL94V-0,-25 85 C,NATURAL 4PCS MOLEX 39-01-4033

X1 COLOR X2 X3 X4 X5 X6 X7 X8 X9 SIGNAL

1 CORE WIRE YELLOW X2 CORE VIDEO1

2 YELLOW 3 AUDIO1

3 RED 1 12VDC

4 BLACK+SHIELD+EARTH+BRAID X2 SHELL 2 GND

5 CORE WIRE RED X4 CORE VIDEO2

6 RED 3 AUDIO2

7 RED 1 12VDC

8 BLACK+SHEILD+EARTH+BRAID X4 SHELL 2 GND

9 CORE WIRE WHITE X6 CORE VIDEO3

10 WHITE 3 AUDIO3

11 RED 1 12VDC


13 CORE WIRE BLUE X8 CORE VIDEO4

14 BLUE 3 AUDIO4

15 RED 2 12VDC


D

C

B

A

B

C

D

4 3 2


1

A

34 2 1

SIZE

TITLE


DWG NOMVN-7001HB B


ANG MACH = ± 1.0 BEND = ± 3.0 X.XX = ± .02

X.XXX = ± .005


REVDATE

2016/4/29


DRAWN BY 2016/4/29

JB

REVISIONS



D

C

B

A

B

C

D

4 3 2


1

A

34 2 1

SIZE

TITLE


DWG NOMVN-7001HB B


ANG MACH = ± 1.0 BEND = ± 3.0 X.XX = ± .02

X.XXX = ± .005


REVDATE

2016/4/29


DRAWN BY 2016/4/29

JB

REVISIONS



D

C

B

A

B

C

D

4 3 2


1

A

34 2 1

SIZE

TITLE


DWG NOMVN-7001HB B


ANG MACH = ± 1.0 BEND = ± 3.0 X.XX = ± .02

X.XXX = ± .005


REVDATE

2016/4/29


DRAWN BY 2016/4/29

JB

REVISIONS



D

C

B

A

B

C

D

4 3 2


1

A

34 2 1

SIZE

TITLE


DWG NOMVN-7001HB B


ANG MACH = ± 1.0 BEND = ± 3.0 X.XX = ± .02

X.XXX = ± .005


REVDATE

2016/4/29


DRAWN BY 2016/4/29

JB

REVISIONS



D

C

B

A

B

C

D

4 3 2


1

A

34 2 1

SIZE

TITLE


DWG NOMVN-7001HB B


ANG MACH = ± 1.0 BEND = ± 3.0 X.XX = ± .02

X.XXX = ± .005


REVDATE

2016/4/29


DRAWN BY 2016/4/29

JB

REVISIONS



D

C

B

A

B

C

D

4 3 2


1

A

34 2 1

SIZE

TITLE


DWG NOMVN-7001HB B


ANG MACH = ± 1.0 BEND = ± 3.0 X.XX = ± .02

X.XXX = ± .005


REVDATE

2016/4/29


DRAWN BY 2016/4/29

JB

Documents

MVN-7001H - REV B - MobileView · x.xxx = ± .005 interpret dimensions and tolerances per asme y14.5m-2009 date rev 2016/4/29 third angle projection drawn by 2016/4/29 jb. p7 p6 p4