Upload
henry-huayhua
View
53
Download
0
Tags:
Embed Size (px)
Citation preview
1TM
REPAIR MANUALTRANSFER CASE
MVG-1600
MARMON-HERRINGTON ALL-WHEEL DRIVE13001 Magisterial Drive • Louisville, KY 40223
(502) 253-0277 • (800) 227-0727 • Fax (502) 253-0317
E-mail: [email protected]
JW09/00
TM
2 TM
TABLE OF CONTENTS
Page
PREFACE ...................................................................................................................................................... 3
GENERAL WORKING DIRECTIONS............................................................................................................ 4
TECHNICAL DATA ........................................................................................................................................ 6
ADJUSTMENT DATA .................................................................................................................................... 7
TIGHTENING TORQUES .............................................................................................................................. 7
CROSS SECTION VIEW (WITHOUT INTERAXLE DIFFERENTIAL) ........................................................... 8
CROSS SECTION VIEW (WITH INTERAXLE DIFFERENTIAL AND OIL PUMP) ....................................... 9
EXPLODED VIEW (300 WITHOUT INTERAXLE DIFFERENTIAL) .............................................................. 10
EXPLODED VIEW (396 WITH INTERAXLE DIFFERENTIAL AND OIL PUMP) .......................................... 11
CONSUMABLES ........................................................................................................................................... 12-14
TIGHTENING TORQUES STANDARD ......................................................................................................... 16
DESCRIPTIONS OF REPAIR ........................................................................................................................ 17-64
MARMON-HERRINGTON ALL-WHEEL DRIVE13001 Magisterial Drive • Louisville, KY 40223
(502) 253-0277 • (800) 227-0727 • Fax (502) 253-0317
E-mail: [email protected]
TM
3TM
PREFACE
The present document gives directions to the trained personnel to repair the
MARMON-HERRINGTON Transfer Case MVG 1600 300/396
Customary tools and devices, which are workshop standard, are supposed to be available.
Required special tools are listed in an overview chart.
Special tool are kept at the necessary level, they bear a tool number and can be purchased fromMarmon-Herrington.
Disassembly and assembly of one version only is explained in this document. Differing workingsequences of other possible versions can easily be recognised by the skilled professional. Forsuch jobs see enclosed sectional and perspective views.
The repair of the component may require changed working sequences or/and differing adjustmentor checking data, according to the technical development of the product over the years.
Therefore, we recommend rendering your Marmon-Herrington Product only to the hands ofperiodically trained personnel.
Damages caused by improperly or unprofessionally executed repair work through untrainedpersonnel and the resulting consequences are excluded from any contractual liability.
This also applies when NON-ORIGINAL-PARTS are being used.
The After Sales Service of MARMON-HERRINGTON,
Fax : (502) 253-0317 Tel : (502) 253-0277
is at your disposition to consult and to assist.
4 TM
GENERAL WORKING DIRECTIONS
The company repairing Marmon-Herrington Components is in any case responsible for all aspectsof safety.
The valid safety regulations and legal directives have to be obeyed to avoid injury of persons anddamage of the product during maintenance and repair.
The proper repair of the Marmon-Herrington Product requires adequately trained personnel. Toundergo training is the obligation of the repairer.
Always assure professional and clean working conditions. Components shall always be cleanedbefore disassembly.
The use of indicated special tools is a precondition.
After disassembly, all parts have to be cleaned. This applies in particular to corners, nooks and oilcatchers in housings and covers.
Carefully remove old sealing compound.
Clean surfaces thoroughly before sealing.
Lubrications bores, grooves and pipes are to be checked to be free from obstructions. They mustbe free from deposits, contamination and preservatives. The latter applies particularly for newparts.
Parts that are being damaged during disassembly are to be replaced by new ones.
E.g.: radial oil seals, o-rings, groove-rings, seal cups, protection caps a. s. o.
Parts as bearings, thrust washers, synchromesh parts etc., which are liable to normal wear haveto be checked by the skilled professional. He judges if a part can be reused or not.
Parts, which have a shrink fit, must be driven to their end position after cooling down to assureperfect seating. Before pressing-in parts like shafts, bearings etc. both contact surfaces must beoiled.
On the assembly all given adjustment tolerances, check data and tightening torques have to beobserved. Marmon-Herrington Components are to be filled with lubricant after the repair Observefilling instructions and lubrication chart. After filling, the oil drain plugs and oil level plugs must betightened to correct torque.
Use Original - Marmon-Herrington Parts only!
5TM
NOTE: This page left blank intentionally
6 TM
Technical Data
MVG 1600 A = 300 mm A = 396 mmMax. input torque 18 000 Nm (13 275 lbft) 18 000 Nm (13 275 lbft)Max. input speed 2800 rpm 2800 rpmRatios on-road off-road
1:0,890 1:1,536on-road off-road1:0,890 1:1,536
Weight including interaxle diff. appr. 315 kg appr. 300 kgWeight without interaxle diff. appr. 305 kg appr. 290 kgAmount of oil needed with diff. appr. 7,2 l
without diff. appr. 7,8 lwith diff. appr. 6,5 lwithout diff. appr. 7,5 l
Oil quality SAE 90 according toMIL-L-2105-API-GL 4
SAE 90 according toMIL-L-2105-API-GL 4
7TM
Adjustment
Item Designation Dimensions Remarks
1
2
3
4
End play of drive shaft bearings
End play of Intermediate shaft
End play of output shaft bearings front
Preload of output shaft bearings, rear(only for the VG 1600with interaxle differential)
0,06-0,12 mm
0,4 - 0,6 mm
0,02 - 0,08
0,0 - 0,05 mm
to be adjusted with shims
to be adjusted with shims
to be adjusted with shims
to be adjusted with shims
5 Flange temperature for assembly heat to 120° C
Tightening Torques
Item Designation Nm Remarks
M1
M2
M3
M4
M5
Collar nuts for flanges
Fastening bolts for planetary carrier
Housing bolts
Slotted nut (Input shaft)
Slotted nut (Intermediate shaft)
1080 Nm
30 Nm+ 90° + 5°
195
600 Nm +/-60
600 Nm +/-60
to be held with holdingdevice TS 215 W
lock by driving-in lockingcollarlock by LOCTITE 243
Adjustment
0.06-0.12 mm
0.4 - 0.6 mm
0.02 - 0.08
0.0 - 0.05 mm
8 TM
MVG 1600 (without interaxle differential)
9TM
MVG 1600 (with interaxle differential and oil pump)
10 TM
MVG 1600 / 300 (without interaxle differential)
11TM
MVG 1600 / 396 (with interaxle differential and oil pump)
12 TM
12
Consumables__________________________________________________________________________
Consumables for repair of a transfer case are lubricants, slip additives, sealants, lockingadhesives, preservatives and cleaning agents.
Table of consumables for unit repair.
Symbol Designation of compound Product name
F1 Standard grease STABUTHERM-GH 461
G1 sliding additive MOLYCOTE M55
D1 Sealing compound DIRKOB1
B2Locking adhesive
LOCTITE 243 (blue)
LOCTITE 638 (green)R1 Cleaning agent Loctite sealant remover
In the following diagram grease, sliding additive, sealing compounds and locking adhesives areindicated with their symbol and point to the components to be treated.
13TM
Consumables MVG 1600 / 300
14 TM
Consumables MVG 1600 / 396
15TM
NOTE: This page left blank intentionally
16 TM
Tightening Torques Standard
17TM
DESCRIPTION OF REPAIR WORKS
Page1 Working on the transfer case unit ................................................................................... 18
1.1 Disassembly of transfer case .......................................................................................... 19
1.1.1 Pull-off flanges, deinstall bearing covers, shifting cylinder and frontaxle output shaft, dismount housing ................................................................................ 20-24
1.1.2 Dismounting of drive shaft, intermediate shaft, differentialgear or output shaft ......................................................................................................... 25-28
1.2 Assembly of transfer case ............................................................................................... 29
1.2.1 Installing bearing carrier and determining shim thickness andinstalling bearing covers .................................................................................................. 30-32
1.2.2 Installing drive shaft, intermediate shaft, differential gear oroutput shaft, install housing ............................................................................................. 33-35
1.2.3 Installing bearing housing, bearing cover and speedometer housing ............................. 36-38
1.2.4 Setting end play of drive shaft, intermediate shaft and differential gearor output shaft ................................................................................................................. 39-40
1.2.5 Check of the end play of drive shaft and differential gear oroutput shaft ..................................................................................................................... 41
1.2.6 Installing front drive shaft bearing cover, front axle output shaftand shifting cylinder ........................................................................................................ 42
1.2.7 Shifting system (with spring) ........................................................................................... 43
1.2.8 Shifting system (without spring) ...................................................................................... 43
1.2.7.1 Shifting system (pneumatic) with spring deinstall / install ............................................... 44
1.2.8.1 Shifting system (pneumatic) without spring deinstall / install .......................................... 45
1.2.7.2 Adjusting Shifting system (pneumatic) with spring .......................................................... 46
1.2.8.2 Adjusting Shifting system (pneumatic) without spring ..................................................... 47
1.2.9 Install and adjust shifting system for interaxle differential lock orfrontwheel drive ............................................................................................................... 48
1.2.10 Installing flanges, oil pipe and breather ........................................................................... 49-50
1.3 Work on transfer case components ................................................................................ 51
1.3.1 Check and measurement of transfer case housing ......................................................... 51
1.3.2 Assembly & disassembly of the front axle output drive ................................................... 51-54
1.3.3 Assembly and disassembly of the drive shaft ................................................................. 55-56
1.3.4 Assembly and disassembly of the intermediate shaft ..................................................... 56
1.3.5 Assembly and disassembly of the differential gear ......................................................... 57-63
1.3.6 Assembly and disassembly of the output shaft(without interaxle differential) .......................................................................................... 63-64
18 TM
1. Working on the transfer case unit
1.1 Disassembly of transfer case
1.2 Assembly of transfer case
Contains: Setting of transfer case shifting system 1Setting of interaxle differential lock 2
Additional work: Oil change(changing of oil only when transfer case is warm)
1 Oil filling plug2 Oil drain plug3 Oil level plug4 Breather
Drain oil by unscrewing both oil drain plugs (2)Install oil drain plugs (2) with new sealsFill oil through oil filling bore (1) until it starts to overflow at oil level bore (3)After setting of correct oil quantity Install oil level plug (3) with new sealClean and install breather (4)
19TM
1.1 Disassembly of transfer case
1 Remove drain plugs (1/1) and drain oil.Deinstall oil pipe (1/2)
1.1.1 Pull-off flanges, deinstall bearing covers,shifting cylinder, and front axle output shaftdismount housing
2 Loosen flange nuts with a torque multiplier (2/1).Use holding device TS 215W (2/2)
3 Pull-off flanges from the shafts with extractorA/VG 2000-05 (3/1).
4 Remove bearing cover (4/1) from the rear axledrive shaft (take out setting shims).
1.1
Pic. 1
Pic. 2
Pic. 3
Pic. 4
20 TM
5 Press out bearing carrier (5/1) at rear axle shaftfrom housing with extractor (KUKKO & screwsM8) (5/2).
6 Unscrew the clamping screw (6/1) of thespeedometer shaft.
Mount striking weight SK 17828/A (6/2) andlightly knock the speedometer shaft out of thehousing.
7 Remove the lid (7/1) of the speedometer housing.
8 Remove the retaining ring (8/1) andspeedometer gear (8/2) from the intermediateshaft. Pay attention to the driver ball.
1.1.1
Pic. 5
Pic. 6
Pic. 7
Pic. 8
21TM
9 Remove speedometer housing (9/1).
10.1 Without oil pump:Unscrew cover (1) and intermed. plate (2) of driveshaft rear.
10.2 With oil pump:Remove cover (10/1) of oil pump housing at rearof drive shaft. Remove lid of PTO interface (10/2).Remove hollow screw and driver ball.
11 Unscrew cylinder screws1) M6 x 35 (11/1)
M6 x 30 (11/2).
12 Pull off the oil pump housing (12/1) with 2 screws(12/2) M6x60.
1.1.1
Pic. 9
Pic. 10
Pic. 11
Pic. 12
22 TM
13 Remove oil pump ring gear (13/1) and innergear (13/2).
14 Remove driver ball (14/1) with magnetic rod(14/2).
15 Remove oil pump housing (15/1) with spacerplate from rear side the drive shaft.
Dismount oil pump cover (4) inside oil pumphousing and remove spring pin (5).
Turn transfer case
16 Remove front bearing cover (16/3) from drive shaft(remove setting shims).Block intermediate shaft with deviceA-VG 1600-03.
Unscrew grooved nut (16/1) of drive shaft withwrench 1 SKO-100-20Unscrew grooved nut (16/2) of drive shaft withwrench 1 VOZ 006920
1.1.1
Pic. 13
Pic. 14
Pic. 15
Pic. 16
23TM
1.1.1
Pic. 17
Pic. 18
Pic. 19
Pic. 20
17 Remove lid and cylinder (17/1) from shift rod
18 Unscrew rear housing bolts (18/1) M16 x 100(10 pieces).
19 Turn transfer case over
20 Unscrew fastening nuts (19/1) and pull off frontaxle drive complete with 2 screws (19/2)M8 x 40.
21 Remove shims (20/1) from the front axle driveshaft.
24 TM
22 Unscrew retaining ball guide (21/1).(Pay attention to spring and ball)
23 Remove shift stopper (22/1).
24 Remove front bearing cover (23/1) from driveshaft.
25 Remove shims (24/1).Remove sealing rings (24/2).
1.1.1
Pic. 21
Pic. 22
Pic. 23
Pic. 24
25TM
1.1.2
Pic. 26
Pic. 27
Pic. 28
26 Unscrew housing screws (26/1) M16x130(12 pieces).
27 Lift off housing cover with lifting device (27/1)M12. (do not incline or rock).Do not jam shifting rod (27/2).
1.1.2 Dismounting of drive shaft, intermediateshaft, and differential gear or output shaft
1 Lift out interaxle differential gear (28/1)with lifting device TS 211 W (28/2).Remove retaining washer (2) and spring.
CAUTION: Pressure spring is compressed.
26 TM
1.1.2
Pic. 29
Pic. 30
2 Remove oil guide panel (29/1).
3 Remove roller bearings (30/1).
Without interaxle differential
4 Lift out rear axle output shaft (1) from housing.Use lifting device TS 211W
27TM
1.1.2
Pic. 32
Pic. 33
Pic. 34
Pic. 35
Deinstall drive shaft and intermediate shaft
5 Lift-up interm. shaft (32/1) approx. 45 mm.
6 Set interm. shaft sidewards on support (33/1)
7 Lift out drive shaft complete (34/1) withshifting rod, shifting sleeve and shifting fork(34/3) use tool TS 212 W (33/2).
8 Lift out interm. shaft (35/1) using lifting deviceTS 222 W (35/2).
28 TM
9 Knock retainer spring pin (36/1) out of housing.
10 Remove oil guide panel (37/1) from housing byturning it.
11 Remove all bearing rings (38/1) from both housinghalves.
12 Remove front and rear bearing (39/1) fromhousing halves (Setting tool TS 223 W).
1.1.2
Pic. 37
Pic. 38
Pic. 39
29TM
1.2
Pic. 41
Pic. 42
Pic. 43
1.2 Assembly of transfer case
1 Install oil panel (41/1) for interm. shaft andfix with spring pin.
2 Install bearing rings (42/1) in front housing.
3 Install rear roller bearing (43/1) for intermed shaft.Use setting tool TS 223 W.
30 TM
1.2.1 Installing bearing carrier, determining shimthickness and installing bearing covers
1 Insert the four-point bearing (45/1), with thenotches for the locking pin (45/2) pointinginward, into the bearing carrier (46/2).
2 Push the locking pins (46/3), with the inclinedsurface pointing to the four-point bearing, flushinto the holes in the bearing carrier (46/2).
3 Press roller bearing (46/4) into the bearingcarrier with support disk TS 213 W (47/1).
4 Measure distance from bearing support surfaceto roller bearing surface (A1).
1.2.1
Pic. 45
Pic. 46
Pic. 47
Pic. 48
31TM
1.2.1
Pic. 49
Pic. 50
Pic. 51
Pic. 52
5 Measure projection of bearing seat onthe bearing cover for rear axle output shaft (B1).
6 Determine thickness (X1) of shim.Bearing adjustment: 0.0 - 0,05 mm pretension(P)
X1 = A1 - B1 + P
Shim thickness S = 0.75 mmS = 0.80 mmS = 0.90 mmS = 1.00 mmS = 1.25 mm
7 Apply sealant DIRKO to bearing support
8 Press bearing support (51/1) into the rear housing,use screws M12x90 (51/2), nuts (51/3)and washers (51/4).ATTENTION: After assembly remove excess
sealant from the lube oil borehole (51/5).
Unscrew auxiliary bolts.
9 Apply LOCTITE 638 to seal carrier with sealrings (52/1) and press into bearing cover withsetting tool (52/2) SKO-026494.
32 TM
10 Apply DIRKO sealant to bearing cover of therear axle output shaft.
ATTENTION: Make sure that no sealantenters the lube oil ducts (53/1).
11 Install bearing cover (54/1) with the correctshims X1 (54/2).
Turn transfer case over.
12 Heat bearing (55/1) to 80°C and push ontothe bearing seat of the bearing carrier (55/2).
1.2.1
Pic. 53
Pic. 54
Pic. 55
33TM
1.2.2
Pic. 56
Pic. 57
Pic. 58
Pic. 59
1.2.2 Installing drive shaft, intermediate shaft, anddifferential gear or output shaft
1 Temporarily install interm. shaft (56/1) with liftingdevice (TS 222 W) (56/2).
2 Set intermed. shaft aside on the 45 mm support.(57/1)
3 Install drive shaft (58/1) with shifting fork(partnumber on top) and shifting rod (58/3).Use tool TS 212 W (58/2). Tighten clampingscrews (4), lock with LOCTITE 243.Tightening torque: 50 Nm
4 Bring interm. shaft (59/1) into installationposition.
ATTENTION:When installing the interm. shaft, make sure thatthe roller bearing does not incline or jam.
34 TM
1.2.2
Pic. 60
Pic. 61
Pic. 62
Pic. 63
Shifting system with spring
5 Compress pressure spring (60/1) and retainingwasher (60/2) together and lock by turningwasher a 1/4 turn.
Version with differential
6 Install oil panel (61/1) with differential gear.Use lifting device TS 211W.
Version without differential
7 Install rear axle output shaft with oil panelUse lifting device TS 211 W.
8 Apply DIRKO sealant to the contact surface ofthe housing.
35TM
1.2.2
Pic. 64
Pic. 65
Pic. 66
Pic. 67
9 Slip-in shifting rod (64/1) in and installhousing half.
10 Tighten 2nd housing half with screws to 125 Nm.Install studs (65/2) with LOCTITE 243.
11 Install front bearing for interm. shaft with settingtool (66/1) A-VG-1600-01 and centering toolA-VG-1600-02.
Turn over transfer case.
12 Tighten remaining housing bolts (67/1) to 125Nm.
13 Block intermediate shaft with device A-VG1600-03Tighten grooved nut (2) of drive shaft with wrench1 SKO 400720.Tightening torque: 600Nm, lock by driving-inlocking collar 2 times.Tighten grooved nut (3) of intermed. shaft withwrench 1 VOZ 006920 (chamferred side of nuttowards exterior). Torque 600Nm. Secure withLOCTITE 243).
36 TM
1.2.3
Pic. 68
Pic. 69
Pic. 70
Pic. 71
1.2.3 Installing bearing housing, bearing coverand speedometer housing
Without oil pump1 Apply DIRKO sealant to oil pump / bearing
housing (2) and intermediate plate (1) and install.
With oil pump2 Apply DIRKO sealant to bearing / oil pump
housing.Insert rear oil pump lid (69/1) into housing. Installspring pin (69/2) to prevent turning.
3 Mount bearing housing (70/1), with intermediateplate (2). Put driver ball (70/1) into dead endbore of drive shaft with grease.
4 Slide inner oil pump gear (71/1) onto drive shaft.
37TM
1.2.3
Pic. 72
Pic. 73
Pic. 74
Pic. 75
5 Install oil pump ring gear (72/1) in oil pumphousing and tighten with cylinder bolts (72/2)
2 pcs. M6 x 302 pcs. M6 x 35.
6 Mount rear bearing housing lid (73/1) (onbearing housing) with DIRKO sealant.
7 Mount sealing lid (74/1) with DIRKO(seal screws too).
8 Install hollow screw (75/1), sealing ring (75/2), andball (75/3) in bearing / oil pump housing.
38 TM
9 Install intermediate ring (3).Mount speedometer housing (76/1) with DIRKOsealant. Fix with 3 auxiliary screws.
Set driving ball (76/2) into bore of interm. shaft.
10 Push speedometer drive gear (or pulsewheel)(77/1) over the driving ball on theintermed. shaft and secure with circlip (77/2).
11 Push speedometer pinion (78/1) into theguide sleeve (78/2). Set o-ring (78/3) into grooveof sleeve and grease.Push speedometer drive into speedometerhousing. Coat threads of clamping bolt (78/4)with LOCTITE 243 and fix speedometer drive.
12 Heat up inner ring (79/1) of cylindrical roller bearingto approx. 80° C and slide it on output shaft.
Turn transfer case over.
1.2.3
Pic. 76
Pic. 77
Pic. 78
Pic. 79
39TM
1.2.4
Pic. 80
Pic. 81
Pic. 82
Pic. 83
1.2.4 Setting end play of drive shaft, intermed. shaft,and differential gear or output shaft
1 Set drive shaft (81/1), intermediate shaft (81/2)and interaxle differential (81/3) to the rear.
Set back outer bearing rings. Free all bearingsby means of light blows, while turning shafts.
Endplay of drive shaft2 Measure projection of drive shaft bearing (82/1)
from the main housing surface (A2).
3 Measure the distance of bearing seat at bearingcover (83/2) of drive shaft (B2).
4 Determine shim thickness, X2Bearing adjustment 0.06 - 0.12 mm end play (a)
X2 = A2 – B2 - a
Shim thickness (s): s = 1.25 mms = 1.30 mms = 1.40 mms = 1.50 mms = 1.60 mms = 1.70 mms = 1.80 mms = 1.85 mm
Note: Recommended end play up to 0.80 mm
40 TM
1.2.4
Pic. 84
Pic. 85
Pic. 86
Pic. 87
End play of differential gear - output shaft5 Measure depth of bearing seat in housing (84/1)
of front axle output drive (A3).
6 Measure projection of front roller bearing (85/1)from differential gear or output shaft (B3).
7 Determine shim thickness XBearing adjustment 0.02 - 0.08 mm end play (a)
X3 = A3 – B3 - a
Shim thickness (s): s = 1.25 mm s = 1.60 mms = 1.30 mm s = 1.70 mms = 1.40 mm s = 1.80 mms = 1.50 mm s = 1.85 mm
End play of intermediate shaft
8 Measure depth of bearing seat in front bearingcover (86/1) of interm. shaft (A4).
9 Measure projection of front roller bearing(87/1)(B4).
10 Determine shim thickness X 4Bearing adjustment 0.4 - 0.6 mm end play (a)
X4 = A4 – B4 - a
Shim thickness (s) = 0.6 mm, 0.8 mm, 1.0 mm
41TM
1.2.5
Pic. 88
Pic. 89
Pic. 90
Pic. 91
1.2.5 Check of the end play of drive shaft anddifferential gear or output shaft
1 Mount bearing cover of drive shaft with thedetermined shims.
2 Shift drive shaft to the back with light blowswhile turning shaft.
3 Screw collar nut (89/1) on drive shaft.
4 Set dial gauge (89/2) on the drive shaft.
Lift drive shaft and read endplay on dial gauge.Endplay too large: Increase shim thickness
accordingly.Endplay too small: Decrease shim thickness
accordingly.
5 Mount bearing housing of front axle output shaftwith the determined shims.
6 Set differential gear or output shaft to the rearwith light blows while turning shaft.
7 Screw lifting device TS 211 W (91/1) in liftingthread of differential gear or output shaft andtighten. Screw plate (91/2) on lifting device.
8 Place dial gauge (91/3) on lifting device TS 211 Wand planetary gear or output shaft. Lift output shaft.Read endplay on dial gauge.Endplay too large: Increase shim thickness
accordingly.Endplay too small: Decrease shim thickness
accordingly.
9 Remove bearing lid of drive shaft and bearinghousing of front axle.
42 TM
1.2.6 Installing front drive bearing cover,front axle output shaft and shifting cylinder
1 Press-in blue seal ring (92/4) and press intobearing with tool (92/1) 1 SKO 100721. Press-inbrown seal ring (92/5) with tool (92/1) 1 SKO100721 and spacer ring (92/2). Use tool SKO-026494 (92/3) as support. Install both dowel pins(6).
2 Apply DIRKO sealant to bearing cover (93/2)and install with correct shims.
ATTENTION: Take care that no sealant enterslube oil passage (93/1).
3 Apply DIRKO sealant to front cover of intermediateshaft and install with correct shims.
ATTENTION: Take care that no sealant enterslube oil passages (94/1) and(94/2).
For assembly of front axle drive, see chapter 1.3.2
4 Apply DIRKO sealant to front axle drive andinstall it with correct shims.
ATTENTION: Take care that no sealant enterslube oil passage (95/1).
1.2.6
Pic. 92
Pic. 93
Pic. 94
Pic. 95
(brown)
(blue)
43TM
1.2.7 / 1.2.8
1.2.7 Shifting system (with spring)
1.2.8 Shifting system (without spring)
44 TM
Deinstall1 Adjusting screw (160/1)
Pressure switch (160/2)Counter nut (160/3).Plate (160/4)
2 Shift cylinder (161/1)Cover (161/2)Piston (161/3)Setting screw (161/4).
Install3 Push O-Ring (162/1) into groove on shifting rod
(162/2) and grease.
4 Install seal (162/3) on piston (162/4) withopen side toward the smaller piston diameterand grease it.
5 Apply DIRKO sealant to sealing surface of theshift cylinder (162/5) and install the shift cylinderon the gear housing.
6 Push piston (162/4) with the open side of theseal (162/3) facing outward, over the shiftingrod (162/2) and fix with circlip (162/6).
7 Apply DIRKO sealant to cover (162/7) and install.
8 Screw in and tighten reduction union (162/8)along with copper seal ring (162/9).
1.2.7.1
Pic. 160
Pic. 161
Pic. 162
1.2.7.1 Shifting system (pneumatic, with spring) deinstall / install
45TM
Deinstall1 Set screw (163/1)
Pressure switch (163/2)Operating cylinder (163/3)Cover (163/4)Piston (163/5)Counter nut (163/6)Clamping screws (163/7)Sliders (163/8)
Install2 Push O-Rings (164/1) into the groove of the
operating shifting rod (164/2) and grease.
3 Install O-Rings (164/3) on pistons and grease.
4 Cover sealing surface of the operating cylinder(164/4) with DIRKO sealant and install ontothe main housing.
5 Push piston (164/5) over the operating rod (164/2) and secure with circlip (164/6).
6 Put DIRKO onto cover (164/7) and assemble.
7 Mount reduction piece (164/8) with copper-sealring (164/9) into the cover and tighten
8 Put DIRKO onto the sealing surface A of flange(165/1) and assembly onto the main housing.
9 Mount locking ball guide (165/2).
10 Mount pressure switch (165/3) and pin (165/4).Check function of switch.
1.2.8.1
Pic. 163
Pic. 164
Pic. 165
1.2.8.1 Shifting system (pneumatic, without spring) deinstall / install
46 TM
Pic. 166
Pic. 167
1 Unscrew set screw (166/1) with counter nut (166/2)in operating cylinder and remove remainders of
LOCTITE.
2 Remove set screw (167/1) together with pressure
switch (167/2) and counter nut (167/3) from the frontmain housing and clean off remainders of LOCTITE.
3 Remove remaining sealant from the threaded boreswith tap M12 x 1.5.
Adjustment of “High”-gear
4 Let engage high-gear by spring force.
Ensure that dog clutch is engaged, by turning
the input shaft at the flange.
5 Coat thread of set screw (166/1) and counter nut(166/2) with LOCTITE 243 and screw into cover(166/3) of the operating cylinder until set screwtouches the piston/piston rod noticeably. Then turnset screw 1/3 to 1/2 turn further and lock withcounter nut.
Adjustment of low-gear
6 Engage low-gear by applying compressed air (P = 7 +/-1 bar) through the connecting union (166/4) in the coverof the operation cylinder. Ensure engagement can byturning the input shaft at the flange.
7 Coat thread of set screw (167/1) and of counter nut(167/3) with LOCTITE 243 and screw into the frontmain housing until set screw touches the piston roadnoticeably. Then turn set screw 1/3 to 1/2 turn and lockwith counter nut.
8 Push pin (167/4) into the set screw (167/1) andmount pressure switch (167/2) with copper seal ring(167/5). Check function of switch.
1.2.7.2
1.2.7.2 Setting of transfer case shifting system (pneumatic with spring) two and three position
47TM
1.2.8.2
1 Unscrew set screw (168/1) with counter nut (168/2)of the shifting cylinder and remove LOCTITEresidues.
2 Dismount set screw (170/1), pressureswitch (170/3) and counternut (170/2), from theflange (170/4) and remove LOCTITE residues.
3 Remove sealant from the threaded bores withtap M12 x 1.5.
4 Coat threads of set screws (168/1 - 170/1) andcounter nuts (168/2 - 170/2) with LOCTITE 243and install into shifting cylinder (168/3)and into flange (170/4).
Adjustment of high-gear5 Engage high-gear by application of compressed air
(P = 7 +/- 1 bar) through the connection union(168/A) of the shifting cylinder (168/3).Ensure engagement by turning the input shaftat the flange.
Turn set screw (168/1) into the shifting cylinder untilit touches the piston rod (168/4) noticeably.Then turn set screw 1/3 until 1/2 turn further andlock with counter nut (168/2) - LOCTITE 243.
Adjustment of low-gear6 Engage low-gear by applying compressed air
(P = 7 +/- 1 bar) through the connection union(168/B) of the operating cylinder (168/3).Ensure engagement by turning the input shaftat the flange. Turn set screw (170/1) into theflange (170/4) until it touches the shiftingrod (170/5) noticeably. Then turn set screw1/3 to 1/2 turn further and lock with counter nut(170/2).
7 Install locking ball guide (170/6). Use LOCTITE 243.
8 Install pressure switch (170/3) and pin (170/7).Check function of switch.
Pic. 168
Pic. 169
1.2.8.2 Setting of transfer case shifting system (pneumatic without spring) two and three position
48 TM
1.2.9
Pic. 99
Pic. 100
Pic. 101
1.2.9 Install and adjust shifting system for interaxledifferential lock or frontwheel drive
3 auxiliary screws M8x25 DIN 933 needed.
Note:If the differential locking mechanism (MVG1600 with interaxle differential) or front wheeldrive shift is adjusted on a installedtransfer case, then the external cover (99/1),cap nut (99/2), setting nut (99/3) and innercover (99/4)must be removed.
1 Remove LOCTITE residues from shift fork (99/5),cap nut, and setting nut threads. Remove sealantresidue from the sealing surface of both covers andbearing housing.
2 Screw down inner cover with auxiliary screws (100/1).
3 Apply LOCTITE 243 to threads of setting nut andcap nut.
4 Insert shifting fork until it stops. Shift dogs must besecurely engaged. Screw counter nut (99/3) ontoshifting fork until it sits on the inner cover (99/4).Turn setting nut 1/3 to 1/2 turn further and lockwith cap nut (99/2).
5 Unscrew auxiliary bolts (100/1).
6 Apply DIRKO sealant to contact surface of thefront wheel drive housing and outer cover andinstall (99/1).
7 Screw in pressure switch (99/6) and copperseal ring (99/7) and tighten.
Adjusting Instructions ADMApply air pressure(7+/-1Bar) to connection ofshift cylinder.Turn flange of front axle output shaftuntil dog clutch engages fully.Turn shaft further byhand,at the same time turn in adjusting screw(100a/1) slowly until turning of shaft becomesharder (shift fork presses onto dog sleeve andfriction brakes shaft).Turn back adjusting screw 1/3 to 1/2 a turn andtighten lock nut (100a/2).
Checks:When shift cylinder is evacuated dog clutch mustnot grind (for this check transfer case must be inhorizontal position with front axle output shaftshowing upwards,allowing dog sleeve to besuspended by the shift fork).Apply air pressure (7+/-1Bar) to connection ofshift cylinder. Within 10 seconds the air pressuremust not drop noticeably.
Check of indication switch:When dog clutch is in “tooth to tooth position”,switch must not give any reading, only whendog clutch is fully engaged, switch must beclosed.
49TM
1.2.10
Pic. 101
Pic. 102
Pic. 103
Pic. 104
1.2.10 Installing flanges oil pipe and breather
1 Apply grease to oil seals (101/1) on the input andoutput shafts.
2 Heat flanges to approx. 120°C and install.
Attention: Install drive flange with groove inflange aligned with oil bore in thedrive shaft.
3 Apply LOCTITE 243 to threads on input and outputshafts.
4 Tighten collar nuts to 1080 Nm. Use deviceTS 215 W (104/1) and torque multiplier(104/2)
50 TM
Installing oil pipe and breather
1 Install oil pipe (105/1).
2 Apply LOCTITE 243 to threads of the breatherand install into transfer case housing (106/1).
3 Install all core plugs coated with LOCTITE 243.
4 Install oil drain plugs (2) and other screw plugs(3) with copper seal ring.
5 Fill gear oil at filling bore (4) until it flowsover at level bore (5). Install level plug withcopper seal ring.
1.2.10
Pic. 105
Pic. 106
51TM
1.3.1 / 1.3.2
Pic. 110
Pic. 111
Pic. 112
1.3 Work on transfer case components
1.3.1 Checking and measuring transfer casehousing parts
1 Visually check bearing bore holes for damageor wear marks.
2 Measure main housing bore holes with internalmeasuring instrument and micrometer.
A .... 139.975 - 140.000B .... 119.978 - 120.000C .... 179.975 - 180.000D .... 154.975 - 155.000
1.3.2 Assembly and disassembly of front axleoutput drive
Disassembly:
1 Deinstall outer cover (111/1), cap nut (111/2) andsetting nut (111/3).Remove inner cover (111/4).
2 Remove circlip from shifting fork.
CAUTION: The piston (112/1) is pressedagainst the circlip by a spring.
3 Remove piston and pressure spring. Removeseal from piston.
4 Remove O-ring and internal circlip from theshifting fork.
52 TM
Pic. 113
Pic. 114
Pic. 115
Pic. 116
5 Press out front axle output shaft. Make surethat shifting sleeve and shifting fork don’t jam.
6 Remove retaining ring (113/1) and pressball bearing (113/2) out of housing.
7 Remove seal (114/1) and seal rings from front axledrive housing.
8 Press out disk and bushing of the shiftingcylinder.
CHECK9 Visually check bearing housing, output shaft,
shifting sleeve, and shifting fork for damageand wear marks.
ASSEMBLY10 Insert disk (116/1) into the bearing housing, with
the the spring seat groove facing upward.
1.3.2
53TM
1.3.2
Pic. 117
Pic. 118
Pic. 119
Pic. 120
11 Apply DIRKO sealant to the unchamfered face Aof the bushing (117/1) and press it in, face Apointing inward.
12 Insert ball bearing (118/1) into housing, pressingon the outer ring, and install circlip (118/2).
13 Install shifting fork (119/1) and shifting sleeve(119/2), into the housing with the shift dogsfacing up.
14 Press in front axle output shaft (120/1). Whiledoing this, support inner ring of the ball bearingwith base SKO-026530 (120/2).Take care shifting sleeve and shifting forkdon’t jam.
54 TM
15 Apply LOCTITE 638 to sealing carrier with sealrings (121/1) and press it into housing with settingtool SKO-026526 (121/2).
16 Install inner retaining ring (122/1) on the shiftingfork (122/2). Push O-ring (122/3)into groove onthe shifting fork and grease.
17 Set seal (122/4), open side facing smallerpiston diameter, in the groove of piston(122/5) and grease.
18 Set pressure spring (122/6) over shifting fork intothe cylinder and press together with piston andcirclip until circlip locks with a click(122/7).
Note: Open side of seal ring (122/4) must faceout.
19 Further assembly explained in chapter 1.2
Pic. 121
Pic. 122
1.3.2
55TM
1.3.3
Pic. 123
Pic. 124
Pic. 125
Pic. 126
1.3.3 Assembly, disassembly of drive shaft
DISASSEMBLY1 Pull off roller bearing (123/1) and small drive gear
(123/2) from drive shaft with two-armpuller KUKKO 20-3 (123/3) and puller hookKUKKO-3-300P (123/4). Remove shifting sleeve(123/5).
2 Pull roller bearing (124/1) and big drive gear(1242) from drive shaft with two-armpuller KUKKO 20-3 (124/3)and support diskTS 214 W (124/4).
CHECK
3 Visually check shaft and drive gears for damage,scratches and wear marks.
Note: If a new shaft is used, set baffle washer into theshaft. Use LOCTITE 243 (125).
ASSEMBLY
4 Oil sliding surface of big drive gear (126/1)andpush onto drive shaft. Heat roller bearing (126/2)to 80°C and install.
56 TM
1.3.4
Pic. 127
Pic. 128
Pic. 129
5 Push on shifting sleeve (127/1). Oil sliding surfaceof small drive gear (127/2) and push onto driveshaft. Heat roller bearing (127/3) to 80°C andinstall.
1.3.4 Assembly, disassembly of intermediate shaft
DISASSEMBLY
1 Pull inner bearing rings (128/1 and above) withtool KUKKO 18-2 (128/2) and separator KUKKO17-2 (128/3) from intermediate shaft.
CHECK2 Check bearing points and gear teeth for damage,
wear, and cracks.
ASSEMBLY
3 Heat inner bearing (129/1) to 80°C and push ontothe interm. shaft.
57TM
1.3.5
Pic. 130
Pic. 131
Pic. 132
Pic. 133
1.3.5 Assembly, disassembly of differential gear
DISASSEMBLY
1 Punch mark fastening screws (130/1) beforeunscrewing. If screws are already marked, thendo not reuse them.
2 Press planetary carrier (131/1) off the gear (131/3) with 3 auxiliary screws M 10 x 55 (131/2).
3 Lift up roller bearing (132/1) with 2 prybars 2165-2 (132/2).
4 Completely remove roller bearing from planetarycarrier with support disc TS 213 W (133/1) anddouble-arm extractor KUKKO 20-2 (133/2).
58 TM
1.3.5
Pic. 84
Pic. 85
Pic. 86
Pic. 87
5 Remove inner bearing ring (134/1) with pullerKUKKO 18-2 (134/2) and separatorKUKKO 17-2 (134/3) .
6 Push in spring-loaded dowel pins (135/1)and push out planetary axle (135/2).
Note: Cover the bore hole in planetary carrierbefore pulling planetary axle completelyout, because cylindrical pin and pressurespring will jump out.
7 Separate rear axle output shaft (136/1) from ringgear (136/2) by removing retaining ring (136/3).
8 Straighten locked parts of rim by punch (137/1).
59TM
1.3.5
Pic. 138
Pic. 139
Pic. 140
Pic. 141
9 Pull out roller bearing (137/1) with inside extractorKUKKO 21-7 (138/1)and counter support KUKKO22-2 (138/2).
Note: This will damage the roller bearing.It may not be reused.
10 Press outer bearing ring A and oil baffle B outof the drive gear (139/1).
CHECK
11 Visually check bearing points, tooth profiles, anddrive shaft for damage, wear, and scratches.
ASSEMBLY
12 Insert pressure spring (140/1) and dowel pin(140/2) into planetary carrier.
13 Affix thrust washers (141/1) to planetary carrierwith grease.
60 TM
14 Oil needle cages (142/1) and push intoplanetary gears (142/2).
15 Press spring loaded dowel pin (143/2) intoplanetary carrier and push in planetary axle(143/1).
16 Insert the planetary gears (144/1) with needlecages (142/1) and push in planetary axle (144/2)until cylindrical pin audibly clicks into bore on theplanetary axle.
17 Heat inner bearing ring (145/1) to 80°C and pushonto rear stub of the planetary carrier.
1.3.5
Pic. 142
Pic. 143
Pic. 144
Pic. 145
61TM
1.3.5
Pic. 146
Pic. 147
Pic. 148
Pic. 149
18 Press roller bearing (147/1) into rear axle driveshaft 146/2) with supporting disk TS 214 W(146/1).
19 Punch in rim at 3 places for locking(147/1) roller bearing.
20 Set rear axle drive shaft (148/1) into the ringgear (148/2) and fasten with retaining ring(148/3).
21 Set rear axle drive shaft with ring gear into thedrive wheel (149/1).
22 Oil roller bearing (147/1) and planetary gears. Setplanetary carrier (149/2) onto the drive wheel(149/1) so that the marks on planetary carrier anddrive wheel align.
62 TM
Note: Planetary carrier and drive gear can only bereplaced together. In this case, install dowelpin (150/1) in planetary carrier and secureagainst displacement with 2 punch marks.
23 Oil fastening bolts (151/1) and, using the tighteningdiagram, tighten to 30 + 5 Nm.Mark the position of the bolts and tighten themfurther according to tightening diagram with anangle of 90° + 5°
24 Insert oil baffle (152/1) in drive wheel (152/2)and press in with setting toolSKO-026506 (153/1).
25 Press outer bearing ring (152/3) into drivegear (152/2) with setting tool SKO-026506(153/1).
1.3.5
Pic. 150
Pic. 151
Pic. 152
Pic. 153
63TM
26 Heat bearing (154/1) to 80°C and slide ontothe front bearing seat of planetary carrier (154/2).
1.3.6 Assembly, disassembly of output shaftWithout interaxle differential
DISASSEMBLY
1 Pull bearing (155/1)from the output shaftwith two-arm extractor KUKKO 20-2 (155/2).
2 Pull outer bearing ring (156/1) out of output shaftwith two-arm extractor KUKKO 20-2 (156/2).
CKECK
3 Check bearing points and gear teeth for damage,wear, and cracks.
ASSEMBLY
4 Press outer bearing ring into output shaft withsetting tool SKO-026506 (157/1).
1.3.6
Pic. 154
Pic. 155
Pic. 156
Pic. 157
64 TM
5 Heat roller bearing (158/1) to 80°C and push ontofront bearing seat of the output shaft (158/2).
1.3.6
Pic. 158
13001 Magisterial Drive • Louisville, KY 40223
(502) 253-0277 • (800) 227-0727 • Fax (502) 253-0317
E-mail: [email protected]
TM
65TM
Method of Payment[ ] Check Enclosed
[ ] Purchase Order/P.O. #_______________________(only w/current M-H Account)
[ ] Mastercard/VISA –Card #____________________________________
Exp. Date__________________
Authorized Card User’s Signature:
_______________________________
MVG 750 Transfer Case TCPM001 6.00
MVG 1200 Transfer Case TCPM002 6.00
MVG 2000 Transfer Case TCPM003 6.00
MT 8 Axle AXPM001 6.00
MT 10 Axle AXPM002 6.00
MT 11 Axle AXPM003 6.00
MT 14 Axle AXPM004 6.00
MT 17 Axle AXPM005 6.00
MT 22 Axle AXPM006 6.00
MT 23 Axle AXPM007 6.00
R/RF 22 Axle AXPM008 6.00
CT-8 Axle AXPM009 6.00
Repair Manuals:
MVG 750 Transfer Case TCRM001 10.00
MVG 1200 Transfer Case TCRM002 10.00
MVG 1600 Transfer Case TCRM004 10.00
MVG 2000 Transfer Case TCRM003 10.00
MT10/MT11 Axles ARM001 10.00
MT14/MT17 Axles ARM002 10.00
MT22/MT23 Axles ARM003 10.00
R/RF 22 Axle ARM004 10.00
CT-8 Axle ARM005 10.00
Operators Manuals:
Transfer Cases OMTC-1 10.00
General OMG-2 10.00
Sales Literature –No Charge Part Quantity
MVG 750 Transfer Case TCSL001
MVG 1200 Transfer Case TCSL002
MVG 2000 Transfer Case TCSL003
MT 8 Axle AXSL001
MT 10 Axle AXSL002
MT 11 Axle AXSL003
MT 14 Axle AXSL004
MT 17 Axle AXSL005
MT 22 Axle AXSL006
MT 23 Axle AXSL007
Driver Controlled LockingDifferential
4 Page Brochure PRBR001
Total Sales Literature
Parts Manuals: ExtendedPart Price Quantity Cost:
Marmon-Herrington Literature Order FormCredit Card Orders Or Current Customers’ Purchase Orders May Be Faxed — 502/253-0317
Sub Total:
Total Quantity Sales Literature:
KY Sales Tax:
Shipping:
TOTAL Due:
No Charge
(included) No Charge
Ship Order to the following address
Company: ______________________________________________________________
Name: __________________________________________________________________ Telephone Number: ________________
Address: _______________________________________________________________ Fax Number: ______________________
City/State: ______________________________________________________________ Zip Code: ________________________
Country: ________________________________________________________________ Postal Code: ______________________
PLEASE MAKE COPIES OF THIS LITERATURE ORDER FORM AS NEEDED 6/00
AXSL008
66 TM