MultiDim Tech Spec

1

DALI Command MultiDimintelligent lighting control system

IntroductionThe Philips MultiDim systemconsists of an integrated range ofDALI compatible devices that canbe combined to produce a fullyfunctional lighting control systemfor use with DALI ballasts andLamp Interface Units*.

The MultiDim range includescontrollers, configuration softwareand a DALI/LON Gateway thatallows multiple DALI systems tobe integrated with LON basedbuilding management systems. Allof the MultiDim componentshave been designed to worktogether to make the installationof a DALI network as simple andas trouble free as possible.

This datasheet covers the basicMultiDim control products thatwill form the basis of a DALIsystem, and includes details andspecifications for the followingproducts:

• Modular Control PanelsDCMD100 - DCMD170

• MultiSensor DCMD302

• IR Remote ControlDCMD303

• Transistor DimmerDCMD450

• DIN Rail Power SupplyDCMD400

• Ceiling Mounted PowerSupply DCMD401

Related Products• Philips HF-Regulator DALI

compatible Ballasts. Refer to theseparate datasheet for details

• MultiDim PC Programming Kit(DCMD502). Provides acomplete, PC based, solutionfor the design and configurationof MultiDim Systems. Includes:MultiDim PC Serial Interface(DCMD501), MultiDimProgramming Point(DCMD200/180) and a fullyworking copy of MultiDimToolbox configuration software.Refer to the DCMD502datasheet for details

• DALI/Lon Gateway(DCMD430). Allows multipleDALI systems to be integratedwith LON based buildingmanagement systems. Refer tothe DCMD430 datasheet fordetails

• DALI/Push-button interface(DCMD444). Allows pushbuttons from othermanufacturers to be connectedto the system.

* This document uses the general term“Lamp Interface Unit” (or itsabbreviation “LIU”) to mean any DALIcompatible electronic lamp controller.A Lamp Interface Unit can be afluorescent ballast, a transistor dimmerfor incandescent lamps, or any otherdevice designed to directly drive aparticular lighting technology.

DCMD - Push-button modules

DCMD302 - Ceiling multisensor DCMD303 - IR remote control

About DALI DALI (Digital Addressable Lighting Interface) is a new internationalstandard (IEC929) for lighting control systems.The main features of theDALI standard are as follows:

• Individual Control of Lamps. Each unit in the DALI network has it’sown individual address and can be controlled independently.

• Multi-Channelling. A single control cable can be used to controlseveral different groups of lamps.

• No Mains Switching Required. Lamps can be dimmed or switched onand off using control system commands without any need for mainsswitching.

• Back-Channelling.The information flow on the connecting cable is bi-directional. In addition to commands from controllers, the cable canalso carry status information on the lamp's operating condition.

DCMD450 - 800 W Dimmer

Provisional

• Simple Wiring. All of the units in the system are interconnected usinga simple two-core cable with few restrictions on topology. Up to 64devices can be connected with a maximum cable length of 300metres.

• Easy System Re-Configuration.The operation of the system can bechanged quickly without any modification to the hardware.

• Easy System Modification. If the lighting system needs to be enlarged,new components can be added anywhere on the DALI cable.Existing units can easily be reconfigured to suit changing usagepatterns.

2

DALI Command MultiDim intelligent lighting control system

Introduction The MultiDim product range provides a complete and fully integratedmeans of creating a DALI based digital control systems. MultiDimcomponents support all of the basic functionality of a standard DALIsystem and are easy to install and configure. Designing a MultiDimsystem is a very straightforward process, but there are several thingsthat you need to be aware of.The information on these two pagesshould provide everything that you need to know.

DALI Compatibility andComplianceThe MultiDim controllers can beused with any DALI compatibleballast or Lamp Interface Unit. Inaddition, all MultiDim LampInterface Units (such as the 800Watt Dimmer) and the DALI-LonGateway can be used inconjunction with othermanufacturer's DALI compatiblecontrol systems. However, it maynot be possible (and is notrecommended) to use MultiDimcontrollers on the same system asother types of DALI controller.

Cable Choice The electrical specification forDALI systems provides a greatdeal of flexibility in both thechoice of cable used and how it isinstalled.The basic requirementsare:

• The cable be mains rated.

• 2 wire, 0.5 - 1.5 mm2

• The maximum voltage drop onthe DALI cable must notexceed 2 Volts (for standardcables, this means that the totallength of connecting cable canbe up to 300 metres).

This means that standard mainscable can be used successfully -particularly useful where a systemis being retrofitted to an existinginstallation.

Cable TopologyAs you can see from the layoutdiagram opposite, there are fewrestrictions of the cable topology.

No special terminations arerequired, and there are nocomplex rules about how thenodes should be connectedtogether.

Ring configurations should beavoided, but otherwise the onlyrequirements are that the cablebe continuous throughout, andthat each node be connected tothe cable at some point.

Nodes can be daisy chainedtogether in series and spurs beadded at any point.The cabletopology can be optimised toeither simplify testing or tominimise cable use.

DALI ConnectionsAll MultiDim units are fitted withremovable connectors withpaired terminals for the DALIconnection.These provide asimple means of linking through,and the only requirement is tomaintain the power supplypolarity throughout the system.

Power Supply RequirementsMultiDim Controllers without adirect mains connection must beprovided with power via theDALI control cable.This has theadvantage that no additionalpower cabling is required, but itdoes mean that you have toensure that an adequate powersupply is available on the system.This supply must be designed forDALI use and be capable ofproviding sufficient power tosupply the controllers connectedto the system. In addition, tomaintain signalling integrity, it mustnot be capable of providing morethan 250 mA to the system.

See page 10 for details of thededicated MultiDim Power SupplyUnits.

ConfigurationAll MultiDim units are fullyconfigurable.They are suppliedpre-configured with factorydefault settings that ensure thata system will be functional assoon as the power is applied.

This has the advantage that anewly installed system will providebasic operation from the momentthe power is first applied. Forsimple systems, this may be allthat is required. But for systemsthat are more complex (and togain access to advanced MultiDimfunctions) the system must bereconfigured using one of threedifferent methods:

• Configuration Using ButtonControllers. Eight and fivebutton MultiDim panelcontrollers provide somelimited configuration featuresfrom the control buttons.Theseinclude the ability to store fourpre-set light levels and theability to customise those levels.

• Configuration Using the IRRemote Control Unit.TheMultiDim IR remote controlunit can be used to configure anumber of advanced systemfunctions. For more details seepage 9 of this datasheet.

• Configuration Using MultiDimToolbox software.The MultiDimToolbox (DCMD502) is aWindows based softwareconfiguration tool, designed tomake setting up a complexsystem as simple as possible.See the MultiDim Toolboxdatasheet for more details.

MultiDim Terminal Connections UsingScreened Cable (optional).

MultiDim Terminal Connections UsingStandard Cable.

About MultiDim Systems

DA+

DA+ DA+

SC

SC SC

DA-

DA- DA-

DA+

DA+ DA+

SC DA-

DA- DA-

3


D C M D 4 0 1

9137 005 30303MADE INNORWAY

P ower S upp lyInput: 230VAC 50 - 60Hz 100mAOutput:250mA 16V

DALI ST ATUS

DL

IA

DA

LI P

OW

ER O

UT

1

3 4

2

0/1

8

4

7 6 5

2

3

1L & N

DALI ballast

DALI ballast

DALI ballast

Physicalselection

DA+

ENL

LOCAL CONTROL

Sc DA- DALI POWER

ONOFF

StatusLED

800W DIMMER

DCMD4501 5

2 6

3 7

4 O

About MultiDim Systems

1.The MultiDim system can be used with any DALI compliantelectronic ballast for fluorescent lamps.

2. Power for the controllers can be supplied by the DCMD401(illustrated) or the DCMD400 DIN rail-mounted power supply orany mains connected MultiDim unit such as the DCMD450 Dimmer.

3. Low-cost cable can be used to interconnect all of the systemcomponents.The recommended total length of the cable is max.300 m.

4.The MultiDim Multisensor provides IR, light-level and occupancysensor, which can be used independently or in combined to provideenergy-saving functions such as automatic operation and constantlight level.

5.The MultiDim DCMD450 800 Watt dimmer is a fully compliantDALI LIU for use with incandescent lamps and low-voltage electronictransformers.

6.The single-gang panels can contain one of the control modules.Themodules are available as sliders, rotary controls or button panels.

7.The double-gang panels can contain up to three controller modules.The modules are completely interchangeable within the panel, andcustom panels can be created as desired.

8.The MultiDim IR remote control unit provides both means ofcontrolling individual units and a simple configuration tool. All of themodular controllers and the MultiSensor are fitted with IR sensorand can be used with the remote control.

Typical layout of a MultiDim systemTypical layout of a MultiDim system

4


MultiDim Modular Control Panels

IntroductionA range of DALI compatiblemanual control panels that can beconfigured to suit almost anycontrol requirement.The rangeincludes pushbutton, rotary, andslider control modules, all ofwhich can be inserted into eithersingle or triple gang fascia panels.The modular constructionprovides flexibility and allowsmany different panelconfigurations to be constructed.

All of the control modules arefitted with indicator LEDs and anIR receiver that allows themodule operate with theMultiDim IR remote control unit.

ConfigurationEach control is supplied pre-configured with immediatelyusable default settings, but can beeasily re-configured to suit aparticular application using eitherthe MultiDim IR Remote, orMultiDim Toolbox configurationsoftware.The eight and fivebutton controllers also providelimited configuration featuresusing the control buttons.

1

2

3

4 O

1 5

2 6

3 7

4 O

1

2

3

4 O

IR Receiver Eight Button

Two Button On/Off Rotary - Push On/Off

Five Button + Raise/Lower Five Button

Slider Double Slider

Two Button - Raise/Lower Blank Panel

IntroductionA range of DALI compatiblemanual control panels that can beconfigured to suit almost anycontrol requirement.The rangeincludes pushbutton, rotary, andslider control modules, all ofwhich can be inserted into eithersingle or triple gang fascia panels.The modular constructionprovides flexibility and allowsmany different panelconfigurations to be constructed.

All of the control modules arefitted with indicator LEDs and anIR receiver that allows themodule operate with theMultiDim IR remote control unit.

IR Receiver

5


MultiDim Modular Control Panels

Module DimensionsThe chassis plates and fasciapanels are designed to fit bothDIN and UK standard backboxeswith a minimum depth of 35 mm.

Mechanical DataThe modular controllers are available in satin white plastic finish.Thevarious control panel combinations can be constructed from thefollowing separately packaged components:

The Control Modules (see opposite for variations).

• Single gang chassis plate and fascia panel, designed for use with astandard, single gang backbox.This provides a mounting for a singlemodule.

• Triple gang chassis plate and fascia panel, designed for use with astandard, double gang backbox.This provides a mounting for up tothree modules.

DALI Cable ConnectionStandard MultiDim removable connectors with paired terminals.A connection between the SC terminal and a local earth is requiredfor EMC protection.

Module Power Supply Requirements13-19 V, 10 mA supplied via DALI network cables.

Conformity & StandardsEMC

Emission: EN 55 015Immunity: EN 61 547

SafetySafety: EN 60 669-1, IEC 60 669-2-1Isolation: 4 kVIP rating: 30

Environmental RequirementsAmbient temperature: 0...35°CStorage temperature: -10...+70°CRelative humidity: 90% maximum, non-condensing.

DA+ SC DA-

DA-DA+ DA+DA-

141.80

73.80

73.80

73.80

35.40 31.80

48.40

6


MultiDim MultiSensor

IntroductionA ceiling mounted module,containing the sensors requiredto provide an automated DALIlighting control system.TheMultiSensor contains an Infra-Redreceiver for use with theMultiDim IR Remote, a constantlight sensor (which measuresreflected light from below thedevice), and a PIR occupancysensor with a range of up to4.5 metres.

PIR OperationThe PIR sensor can be used onits own to provide automaticcontrol of lighting depending onthe room’s occupancy.Theoperation and timing of the PIR isfully configurable and includes theability to set the unit to provide“off only” operation and anadjustable “PIR transition time”that can improve the life-span offluorescent tubes used in corridorapplications.

Local SwitchThe MultiSensor is provided withterminal connectors for a localwall switch.This provides amanual dimming function ifrequired.

ConfigurationThe MultiSensor is supplied pre-configured with immediatelyusable default settings. However, itcan be easily re-configured to suita particular application usingeither the MultiDim IR Remote,or MultiDim Toolbox software.

In addition, the MultiSensor isfitted with five rear mounted DILswitches that will allow some ofthe main functions to be pre-configured.The DIL switchsettings are applied when poweris first applied but can beoverridden using the MultiDim IRRemote, or MultiDim Toolboxsoftware.

Constant Light OperationThe PIR and constant lightsensors operate together toprovide automatic constant lightcontrol of the surrounding lamps.

For effective constant lightoperation, careful positioning ofthe MultiSensor is essential. Inparticular, it is important toensure that the sensor is notexposed to direct light, and that it

is positioned in such a way thatmost of the light that it receives isunder its control. Mount theMultiSensor away from direct lightentering through windows. Seethe installation instructions formore details.The constant lightfeature is disabled by default andmust be enabled using theMultiDim IR Remote Control orMultiDim Toolbox software.

IR Sensor

ConstantLight Sensor

PIR

60°- 85°

4.5 m

0.5 m

3.0 m

3.0 m

120°

3 m

14.0 m

1.6 m

0.8 m

100°

7.1 m

5.2 m

3.0 m

IR Sensor Range and Angle of View

Constant Light Sensor Range and Angle of View (without Restrictor)

PIR Sensor Range and Angle of View

7


MultiDim MultiSensor

Fixing DataThe MultiSensor’s housing isdesigned for push fit mountinginto a ceiling, or inside a luminairecasing. Its spring-loaded mountingsystem will allow it to be fittedinto a wide range of fixingmaterials, including sheet metaland fibrous ceiling tiles. For thinmaterials, a slightly smallermounting hole is required. / 52.0 mm

0.5 mm- 2.0 mm

/ 55.0 mm>2.0 mm

/ 65.00

26.40

51.40

SC DA-DA+

Touch DimmerCable

fadeN.o

Switch (Mains rated)

0.22 - 2.5 mm(Mains rated)

2MomentaryI

Operation

HoldMomentary

5

32

14

OFF

5

DA+SC

DA-

05

32

On

14

OFF

PIR Control

IR Receiver

PIR Test

Factory DefaultSettings

Local Switch

Constant Light

Off

Switch Function

On

Off

Off

40°

2.1 m

3.0 m

Manual Configuration Using the MultiSensor’s DIL switch

Connecting a Local Switch

Fitting the Constant Light Sensor Viewing Angle Restrictor

DCMD302 - for ceiling mounting With the cable shroud removed.

DALI Cable ConnectionStandard MultiDim removable connectors with paired terminals.

Module Power Supply13 - 19 V, 15 mA supplied via DALI network cables.

Constant Light SensorViewing Angle: 100° (40° with viewing angle

restrictor) Range: 5 - 5000 lux.SW1 Switch Functions: On: Set level to nominal value

Off: Defaults to maximum IR Receiver Operation: Omni-directional Frequency: 36 kHz SW2 Switch Functions: On: Receives all remote control

commands Off: Ignores remote controlcommands (except configurationcommands)

PIR Sensor Operation: Omni-directional pyro-electric SW3 Switch Functions: On: Last level recall

Off: PIR response ignored SW4 (PIR Test) Switch Functions: On:Timeout reduced to

10 seconds - use for testing Off: Normal PIR function (default 20 minute time-out)

Local switch Operation: Single mechanical switch

connected as shown provides“touch dimmer” style operation.

SW5 Switch Functions:On: Local Switch enabled.Off: Local Switch disabled.Conformity and Standards (EMC) Emission: EN 55 015 Immunity: EN 61 547 Safety: IEC 60 950 Isolation: 4 kV IP rating: 30 Operating ConditionsAmbient temperature: 0...+50°C Storage temperature: -10...+70°C Relative Humidity: 90% maximum, non-condensing.

8


MultiDim IR Remote Control

1

34

2

0/10/1

+

E

C

D

B

G

A

F

9

D 4

0E 2

5

87 6B

A

F

C

3

1

A. LED Indicator (Flashes when a button is operated)B. Scene Recall/ConfigurationC. On/Off/ShiftD. Modifier KeysE. TransmitterF. Battery CoverG. Rotary Switch (Normal position 0)

IntroductionThe MultiDim Infra-red remotecontrol is designed to work inconjunction with all PhilipsMultiDim products fitted with anIR receiver, including the PhilipsMultiDim control panels andMultiSensor.

The IR Remote is a dual functiondevice. Its main purpose is toprovide a simple and intuitiveremote control for MultiDimcontrol systems.

When used as such, it provides anumber of basic functions,including On/Off, Raise/Lower, andselecting from four predefinedScenes.

However, the IR Remote can alsobe used as a basic configurationtool for simple systems where theuse of MultiDim Toolbox and itsassociated Programming Pointis inconvenient.

In this case, the control buttonsare used in combination toprovide basic configurationfunctions.This includes, creatingand adding to groups of lamps,setting pre-set scenes anddisabling or enabling IR receivers.The IR Remote will allow thesettings to be locked to preventthe user from accidentally makingchanges to the configuration.

Basic Control FunctionsOn/OffRecall Scene 1-4Raise/Lower lamp levelsStore Scene

Configuration FunctionsSet default Preset Levels (1 = 100%, 2 = 75%, 3 = 50%, 4 = 25%)Creating GroupAdd to GroupCreating SceneRestrict the IR Control signal to Specific GroupsDisable/Enable IR sensors on specific controllersConfiguration Lock (prevents users inadvertently changing thesettings)

Technical DataPower: 2 x IEC, LR03/AAA, 1.5 V BatteryWeight: 50 gOperating Frequency: 36 kHzSize: 120 mm x 57 mm x 24 mm

9


MultiDim 800 W Transistor Dimmer

LOCAL CONTROL

DALI

AC

45 m

m

88 mm 58 mm

90 m

m

Physicalselection

DA+

ENL

LOCAL CONTROL

Sc DA- DALI POWER

ONOFF

StatusLED

800W DIMMER

DCMD450

DALI + 250 mA

PhysicalSelectionSwitch

DALI

Status LED

ONON

Physicalselection

DA+

ENL

LOCAL CONTROL

Sc DA- DALI POWER

ONOFF

StatusLED

800W DIMMER

DCMD450

DALI

LOCAL CONTROL

AC

L

N230 V

DA+

DA+DA+

SC DA-

DA- DA-

< 50 m

IntroductionThe MultiDim 800 Watt TransistorDimmer is a fully DALIcompatible Lamp Interface Unit,designed to allow incandescentlamps to be incorporated into aDALI controlled lighting system.

The dimmer is a DIN-railmounted unit that can control amaximum load of up to 800 W.It can be connected to mainsvoltage lamps directly, or to lowvoltage lamps via an electronictransformer designed for bothcapacitive and resistive loads.

The dimmer is provided withlocal switch terminals, an indicatorLED, a physical selection switchand a built-in DALI power supply.

The local switch terminals willallow a momentary push buttonswitch to provide local “touchdimmer” style control.The indicator LED provides statusand fault indications, and thephysical selection switch is usedto identify the device duringsystem configuration.

The DALI power supply is switchactivated, and will provide up tothe maximum of 250 mA, 18 V tothe DALI network.

Note that, if the power supply isenabled, no other source ofpower may be used on thenetwork.

Additional DALI Functions• Min/Max levels, Scenes, Groups• Lamp status report• Dimmer status report

ConnectionDALI: Standard MultiDim removable

connectors with paired terminalsMains: < 4 mm2 solid core

< 2.5 mm2 stranded

PowerMains Supply: 220-240 VAC, 50 HzDALI supply output: 250 mA

Operating ConditionsAmbient Temperature: 0...35°CRelative Humidity: 90% max, non-condensing.

Mechanical dataDIN-rail case 88 mm wide (5 M)

Conformity & Standards (EMC)Emission: EN 55 015Immunity: EN 61 547

SafetySafety: EN 60 950IP rating: 30Isolation: 4 kV, Mains to dimmer unit

(Basic, Dimmer internal isolationto DALI terminals)

Installation Notes1.The dimmer is for use with incandescent lamps and low voltage

electronic transformers. It is not suitable for use with fluorescentballasts or conventional transformers.

2.The external supply must be protected. It is recommended that a 6 A MCB is used.

3. All cabling must be 230 V mains rated.4. For installation in a restricted access location only.

10


MultiDim Power Supplies

DALI

AC

45 m

m

58 mm

90 m

m

70 mm

POWER SUPPLY

DCMD400

DA+

ENL

Sc DA-

Power

L

N230V

AC

DA+DA+ DA- DA-

DA+ SC DA-

DALI

63 m

m

100 mm

D C M D 4 0 1

9137 005 30303MADE INNORWAY

P ower S upp lyInput: 230VAC 50 - 60Hz 100mAOutput:250mA 16V

DALI ST ATUS

DL

IA

DA

LI P

OW

ER O

UT

51 mm

L

L

DA N

N

DALI HF BALLAST

DCMD401

DALIL

N

230V

DA+ DA-

DA+ SC DA-

DALI

DCMD401 DCMD400

DCMD400 Module Dimensions

DCMD400 Module Wiring

DCMD401 Module Dimensions DCMD401 Module Wiring

IntroductionPower for MultiDim devices can be supplied from a number ofdifferent sources. All mains connected MultiDim units (such as the 800Watt Dimmer) are provided with an internal DALI power supply. If thesystem contains one of these, it will provide an ideal source of power.

Alternatively, a dedicated MultiDim power supply unit (DCMD 400 orDCMD 401) can be used. Both of these units have similar outputcapabilities and can supply the maximum of 250 mA permitted for aDALI system. However, the DCMD 400 is designed for DIN railmounting in a control cabinet and the DCMD 401 for mounting in aceiling void.

Note that, if a power supply unit is connected to the system, no othersource of power may be used.

Technical DataMains SupplyDCMD400: 230 VAC (nom), 197-264 VAC(abs);

50 Hz (nom), 48-62 Hz (abs)DCMD401: 230 VAC -10%/ +6%, 50-60 Hz

DALI Supply Output250 mA (nom)

Ambient TemperatureDCMD400: 0...50°CDCMD401: 0...40°C

Relative Humidity90% max, non-condensing

IP rating30

Mechanical DataDCMD400: DIN Rail case 70 mm (4 M)

DALI CableDCMD400: Standard MultiDim removable connectors

with paired terminalsDCMD401: 1 m, 2 x 0.75 mm2 stranded

Mains CableDCMD400: < 4 mm2 solid core

< 2.5 mm2 strandedDCMD401: 1.5 m, 2 x 0.75 mm2 stranded

Installation Notes1.The external supply must be protected. It is recommended that a 2A

MCB is used.2. All cabling must be 230 V mains rated.3.The DCMD400 is for installation in a restricted access location only.

11


MultiDim DALI Controllers

Type Description Ordering 1 Piece EOCnumber EAN1 code * Weight Qty. Dimensions Volume

EAN3 code * gross l x w x hkg pcs cm m3

DCMD100 MultiDim rotary module 9137 005 308.. 8711500 747921 0.076 1 10.0 x 6.0 x 5.2 0.0003 747921 00DCMD110 MultiDim single slider module 9137 005 309.. 8711500 747938 0.079 1 10.0 x 6.0 x 5.2 0.0003 747939 00DCMD111 MultiDim twin slider module 9137 005 310.. 8711500 747945 0.079 1 10.0 x 6.0 x 5.2 0.0003 747945 00DCMD121 MultiDim 2-button on/off module 9137 005 311.. 8711500 747952 0.079 1 10.0 x 6.0 x 5.2 0.0003 747952 00DCMD122 MultiDim 2-button raise/lower module 9137 005 312.. 8711500 747969 0.074 1 10.0 x 6.0 x 5.2 0.0003 747969 00DCMD124 MultiDim 5-button module 9137 005 313.. 8711500 747976 0.077 1 10.0 x 6.0 x 5.2 0.0003 747976 00DCMD125 MultiDim 7-button module 9137 005 314.. 8711500 747983 0.077 1 10.0 x 6.0 x 5.2 0.0003 747983 00DCMD126 MultiDim 8-button module 9137 005 315.. 8711500 747990 0.075 1 10.0 x 6.0 x 5.2 0.0003 747990 00DCMD150 MultiDim single blank module 9137 005 316.. 8711500 748003 0.049 1 10.0 x 6.0 x 5.2 0.0003 748003 00DCMD170 MultiDim IR receiver module 9137 005 317.. 8711500 748010 0.072 1 10.0 x 6.0 x 5.2 0.0003 748010 00DCMD180 MultiDim programming point module 9137 005 318.. 8711500 748027 0.066 1 10.0 x 6.0 x 5.2 0.0003 748027 00DCMD200D MultiDim double frame - white 9137 005 319.. 8711500 748034 0.165 1 20.0 x 12.3 x 4.4 0.0011 748034 00DCMD200S MultiDim single frame - white 9137 005 320.. 8711500 748041 0.096 1 12.2 x 10.0 x 4.4 0.0005 748041 00DCMD302 MultiDim ceiling multisensor 9137 005 301.. 8711500 747877 0.108 1 10.4 x 9.7 x 7.3 0.0007 747877 00DCMD303 MultiDim IR remote control 9137 005 302.. 8711500 747884 0.090 1 13.0 x 6.0 x 2.9 0.0002 747884 00DCMD400 MultiDim DIN rail-mounted power supply 9137 005 304.. 8711500 747891 0.168 1 11.0 x 8.0 x 6.8 0.0006 747891 00DCMD401 MultiDim ceiling-mounted power supply 9137 005 303.. 8711500 748744 0.592 1 12.0 x 5.1 x 6.3 0.0004 748744 00DCMD444 MultiDim DALI/push-button interface 9137 001 820.. t.b.a. t.b.a. t.b.a. t.b.a. t.b.a. t.b.a.DCMD450 MultiDim 800 W dimmer 9137 005 306.. 8711500 747914 0.258 1 10.1 x 9.1 x 6.3 0.0006 747914 00DCMD520 MultiDim PC programming kit 9137 005 307.. 8711500 749802 0.960 1 27 x 22 x 8.5 0.0050 749802 00* For all MultiDim products the EAN1 code and the EAN3 code are the same.

Ordering and packing data

Documents

MultiDim Tech Spec