■ TURN- AND CUT-OFF TOOLS FOR SWISS TYPE LATHES

■ MINIATURE I.D. TURNING TOOLS FROM Ø 0.5 MM

■ FLEXIBLE I.D. TURNING WITH INSERTS

■ MINIATURE CARBIDE DRILLS AND ENDMILLS FROM Ø 0.2 MM

■ THREAD WHIRLING UP TO 12 CUTTING EDGES

■ BACK WORKING TOOLS

■ MODULAR CUTTING TOOL SYSTEM FOR SWISS TYPE LATHES

PRECISION TOOLSFOR THE MEDICAL AND MICROMECHANICAL INDUSTRY

Multidec®-cut 3000

Multidec®-cut 1600

Multidec®-iSO

UTILIS is a Swiss company, specializing in tools for the metal cutting production process used in the micromechanical, medical and watch industry. The product quality is a significant part of our successful strategy. Fulfilling the certificate ISO 9001:2000 requirements are extremely important to UTILIS, and constantly innovating new products is our voluntary exercise. With this philosophy we uphold the excellent reputation of «Made in Switzerland». It’s obvious that the products we deal with are used by customers who look to the same quality demands as UTILIS does. Looking after our clients is not just talking in platitudes for UTILIS, it is our daily business. Being in close contact with our customers allows an intensive exchange of ideas, which gives us the chance to recognize the demands of our customers early and gives us the focus to develop our product line for the future.

A turn and cut-off tool for Swiss type lathes up to bar diameter 32 mm. The cutting inserts consist of two cutting edges and will be mounted on tem-pered tool holders with a cross section from 8 mm to 20 mm. The insert seat, which is protected from contami-nation, warrants a repeatability of < 0.01mm and allows a 100 % utiliza-tion of all cutting edges.

Advantages– Inserts can be reground– Large selection of cuttings with

different chip breaker geometries– Ideal for machining stainless steels

and titanium– Ideal system for large feed rates

The turn and cut-off system 1600 is suitable for Swiss type lathes up to bar diameter 10 mm. The cutting inserts consist of two cutting edges and will be mounted on tempered tool holders with a cross section from 7 mm to 20 mm. The insert seat war-rants a repeatability of < 0.01 mm and allows a 100 % utilization of all cut-ting edges.

Advantages– Large selection of cutting geometries

with different chip breakes specially made for smallest parts

– Full profile threading inserts starting from M 0.2 (0.06 mm pitch)

– Grooving inserts width starting from 0.05 mm

Advantages– Inserts with corner radii of 0.00 /

0.03 / 0.05 / 0.06 / 0.08 / 0.10 / 0.15 / 0.20 / 0.35 / 0.40 / 0.75 / 0.80

– Inserts with sharp cutting edges and with PVC coatings available

That serie consists of ideal coordi-nated ISO standardized inserts and insert holders. On tool holders with a cross section from 8 mm to 25 mm we offer a very large selection of inserts with many different chip breaker geometries, carbide grades and coatings.

Multidec®-BOre MicrO

Multidec®-eASY BOre

Multidec®-SuPerBOre

Multidec®-drill

Multidec®-tOP

Holes from Ø 7.8 mm to 16.0 mm can be machined with these one cut-ting edge inserts. This insert will be mounted on the front face of a steel holder or for deeper holes on a car-bide holder. We offer a large selection of reasonable priced inserts for I.D. turning, grooving, threading and face grooving.

The inside cutting of smallest holes can be machined with turning, grooving and threading tools from Ø 0.5 mm to 8.0 mm. The tools will be mounted in hardened holders, which can be mounted directly in the machine or in collet holders. The carbide cutting tools have an accuracy repeatability inside the holder of < 0.01.

Advantages– Easy cutting edge exchange by hand– Internal cooling channels– Twisted chip area improves the

evacuation of the chip– Cutting depth of 2 × Ø to 6 × Ø

Advantages– Compared to ISO inserts double

feed rate with same surface quality and finish

– Inserts with corner radii of 0.00 / 0.03 / 0.08 / 0.15 / 0.20 / 0.35

– Inserts with sharp and rounded cutting edges

This advancement of the ISO stan-dardized inserts allows the ideal pre-cision turning. The reinforced insert with 86° cutting angle allows front and back turning with large feed rates and still results in very nice surface quality and finishes. Compared to wiper geometries, our TOP geometry is cutting much easier and softer.

Advantages– Internal cooling channels– Easy handling– Good flexibility through inter-

changeability

The development purpose and goal of this tool was to machine a hole with a flat bottom efficiently. Originated is a tool which can drill into solid material, I.D. turn the hole and face turn the part. We have tool holders and inserts available from Ø 8 mm to 32 mm with maximum depths up to 2.25 × Ø for many different materials.

Advantages– A tool with three machining

methods integrated saves two tool spaces

– Optimal chip control– Internal cooling channels

These drills made from carbide, avail-able from Ø 0.3 mm to 20.0 mm, distinguish themselves through their stability, accuracy and self centering ability. With internal cooling they are also available from Ø 1 mm. The HX coating improves the tool life signifi-cantly.

Advantages– Drilling depths from 3 × Ø to 15 × Ø – Range Ø 0.3 mm to 3 mm available

in steps of 0.01 mm

Multidec®-BAcKtOOlS

Multidec®-MOduliNe

Multidec®-Mill

Multidec®-WHirliNG

Utilis AG, Precision Tools

Kreuzlingerstrasse 22, CH-8555 Müllheim

info@utilis.com, www.utilis.com

Phone 41 52 762 62 62, Fax 41 52 762 62 00+ +

Distributed by:

Advantages– More tools per space improve the

flexibility distinctive– Presetting possible– Compatible with the systems from

Applitec, Dieterle and Bimu

Exchange of the original tool holder base plate with our Moduline base plate boosts the profit by means of quickness and reliability. This versatile system for different Swiss type lathes manufacturers consists of a length-wise geared interface and guaranties excellent stability and precise posi-tioning.

This up to 12 cutting edge available thread whirling system improves the productivity in manufacturing signifi-cantly. Compared to thread turning with necessary several cuts the whirl-ing cutting process completes the thread in one operation.

Advantages– System with 9 or 12 cutting edges.– 50 % to 200 % better productivity– High tool life– High surface quality and finish of

the thread profile

Tools for back machining on Swiss type lathes with sub spindle improve the productivity notably. This tool allows a complete and final opera-tion at once. The system distinguishes itself through modularity, stability and uniquely through the easy adjustment of its center heights.

Advantages– Flexible at splitting the cutting time

between main and sub spindle– Base holder for all main Swiss type

lathes available

Miniature carbide end mills from Ø 0.2 mm to 12.0 mm in different lengths cover all necessary milling operations within the micro machin-ing field. These tools are available up to Ø 6 mm in steps of 0.01 mm.

Advantages– Cutting depths from 2 × Ø to 10 × Ø – Qualified for machining all steel,

including stainless steel and titanium

2008

.08

Fly

er M

ult

idec

, e

(2.2

.1)