biomorph ®

multi EL desk electric versio n

Ground Support Equipment (US) ltd., DBA biomorph, 11 Broadway, New York, NY 10004. 888 302 3375 fax: 212 809 4324 info@biomorphdesk.com

USER SIDE

Screw gun w/philips bitTOOL

1

top assembly

frame assembly

2Packed in smallest cartonwith hardware.Use enclosedinstructions to assemble only.

assemble keyboard mech

Place desktops upside down on clean floor.

remove desktops from crate

GROUND SUPPORT EQUIPMENT (U.S.) Ltd.11 Broadway, space 905, New York, NY 10004, U.S.A. Tel: 888 302 DESK. (212) 809-4323 Fax:(212) 809-4324. Email: info@biomorphdesk.comYou are hereby made aware that the content of any material submitted to you [upon your request] by Biomorph/Ground Support Equ. (US) Ltd. in connection with its furniture designs is considered proprietary to Biomorph/Ground Support Equ. (US) Ltd. and protected under federal copyright, trademark and patent laws, and under federaland state unfair competition law. Unauthorized copying, dissemination and/or use, both unintentional and intentional may subject you to payment of damages through legal action. © 2003 Biomorph/Ground Support Equ. (US) Ltd.

Please use the instructionsenclosed with the frame & page2

multibiomorph desk

®

interactive

ASSEMBLY INSTRUCTIONSQuestions? Call 888 302 DESKFor info visit www.biomorph.com

electric

adjustment control switch

use location holes on underside of top to position on frame

3 keyboardsurfaceadjustmentmechanism

grommet holes

frame

keyboard surface tilt knob

optional CPU holder

keyboard surface adjustment lever.squeeze to release, let go to lock.

7

UNDERSIDE OF DESKTOPS

privacy/modesty panelattachment pilot holes

4turn main desktop over

3/4" silver screws x 16 5

! DO NOT OVERDRIVE SCREWS

plastic grommets x 3 7Place grommets in 3 holes.use for wire management.remove to mount add-ons.

Place desktop ontop of frame assy. and use locationholes on surfaceto position frame

Use to attach desktop to support plates from underneath. Drive directlyinto surface. Fill all holes.

33/4" screw x 6

! DO NOT OVERDRIVE SCREWS

Use to attach keyboard mech to keyboard surface.Use pilot holes on bottom of surface.

kb

1 1/2" black hex-head nut-bolt sets x 8found in crate w/tops

wire guide clips 9Use to route wires under surface.Screw directly into surface with supplied screws.

attach controller box, adjustment control switch

8Found with frame. Screw into surface with supplied screwsusing pilot holes. Connect wiresas per frame assy sheet.

6Use to attach keyboard mechanism/small surface assembly to main surface. Insert into thru-holes from topof large surface. Screw tight.

controller box

THROUGH-HOLES FOR BLACK HEX-HEADNUT-BOLT SETS

PILOT HOLES FOR 3/4” SCREWS

IMPORTANTThe completed desk is veryheavy and must not be moved by lifting the surface alone, otherwise damage may occur.

!

6

Page 16 of 36

DPF1C - Desk Panel

Operation of the DPF1C “one reference”

Up and down (

V): Just activate either the up or down button for parallel drive and the system will drive until the button is released again or the system reaches end position.

Memory:The four small buttons are used for memory drive/storing memory.

Store memory• Press S – button, the display will fl ash for 2 seconds• Within these two seconds press one of the small buttons with dots and the position will be stored at this button. • The panel will acknowledge by showing “1”, “2” or “3” in the display depending on chosen position

Memory drive (small buttons with dots) Press one of the memory buttons and the system will start driving to the pre-programmed memory position. Keep the button pressed until the position is reached.

Display functionShows the actual height in either cm or inch.

= Parallel up

V = Parallel down

S = Store memory

• = Memory 1

•• = Memory 2

••• = Memory 3

V

V