MSI Product Catalog

ProductCatalog

Mainland Security Inc.Suite 1204, 12/F, Shanghai Ind. Inv. Bldg.48-62 Hennessy Road, WanchaiHong Kong

Phone: +852 3005 7485Fax: +852 3010 9848Web: www.mainlandsecurityinc.comE-mail: [email protected]

© 2006 Mainland Security Inc. All Rights Reserved. All Trade Marks of Their Respective Owners. Specifications are subject to change without prior notice

GVD4 EXPLOSIVES VAPOUR DETECTOR

The detector, which is completely self-contained and designed for single-hand use,is supplied in an executive-type briefcasewhichalsohouses the followingaccessories:-battery charger, spare battery pack,earphone, interchangeable probes, testsample in container, first line spares kit,cleaning tools and instruction handbook.

The GVD4 Explosives Vapour Detector has been developed from the earlier PD3 series,

and is similar to equipment supplied to the British Army under NATO Stock No. Z5/6665-

99-225-1652. It is designed to facilitate searching people or objects to discover hidden

explosives.

GENERAL DATA

Power input to charger:

220-240v or 110-120v 50/60HzBattery Life:

Minimum 4-5 hours constant use8-12 hours normal intermittent useBattery Recharge Time:

4-5 hoursDimensions:

Carrying Case - 430 x 320 x 110 mmHand unit - 337 x 67 x 50 mmWeight:

Case - blackHand Unit - silver/blackShipping Information:

Dimensions - 510 x 400 x 135 mmWeight - 6.4KgOrdering Information:

GVD4 complete with case andaccessoriesReplacements Available:

Battery PackBattery ChargerShort Probe AssemblyLong Probe AssemblyTest SampleServicing Aids:

Service manual2nd linespares - full listavailableonrequest

PRINCIPLES OF OPERATION

The GVD4 isextremelysimple tooperate, thenumber of controls being reduced to one - aweatherproof ON/OFF switch. The unitautomatically adjusts to the surroundingenvironment, thus alleviating possibleoperator error. Warm-up time is only about10 seconds and a low frequency tone will beemitted when the unit is ready for use.

When the equipment is switched on, acontinuous sample of air is drawn in via thenozzle. A concentration of explosive vapourin the sampled air, exceeding 1 part in 109

by volume, will cause the instrument to emitahigh-pitched tone. The frequencyexcursionof the tone is an approximate measure of theconcentration of explosive vapour sampled.The source can be located by passing theprobe across the area from which theresponse was obtained and listening to thevariations in response. When desirable, thetone can be fed through the earphone so thatit is audible to the operator only. A red light,which is visible to the operator, but not to theperson being searched, also appears when astrong sample is obtained.

The GVD4 is powered entirely from its own12v rechargeable battery pack, which isconnected to the unit by a quick release,weather-proof connector. A fully chargedbattery will last for at least 4 hours continuoususe, or 8-12 hours when used intermittentlyduring typical search conditions.

NATO STOCK NO:

Z5-6665-99-225-1652




VISUAL SEARCH INSPECTION KIT

The new Visual Search Inspection Kit is a new inspection kit which replaces the original SKM Search

Kit. It is designed for use by professional EOD, Customs and Police Search operators for detecting

possible explosive devices (IED's), contraband and crime evidence.

The Visual Search Inspection Kit includes a side viewing endoscope for searching inaccessible areasthroughagapof10mmdiameter. A10Whalogen lamp in the tipof theendoscopeprovidesbright illuminationand enables inspections to be made over distances of up to 1.5m. Power for the endoscope is supplied froma secondary power socket in the fluorescent handlamp included with the kit.

Searchmirrors includea long telescopicmodelthat extends to 1400mm for inspectinginaccessibleareas inandabovecontainers, forexample, and a short fixed length model whichis ideal for room searches. Both can be fittedwith the rangeof interchangeablemirrorheadssupplied. The kit also contains a fluorescenthandlamp to provide a wide area working lightand two right angle torches with belt clips.

Aselectionofminiaturemirrorsand lightprobesand illuminatedmagnifiersare included toassistin the internal inspection of suspect packagesand containers so as to cause minimaldisturbance. Mirror sizes range from 4.5mm indiameter.

The kit is supplied in a protective foam-linedcarrying case complete with batteries andreplacement lamps.

The following mirrors fit both UCM and CEM:

Mirror Convex, glass, 140mm dia (3 perkit)

Mirror Plano, glass, 64mm dia (2 per kit)

Mirror Plano, glass, rectangular, 64 x114mm dia (2 per kit)

Battery Handle 2 C cell (2 per kit)

Clip-on mirrors and accessories to fit 14mm dia. light

probes:

Extension 380mm length, straight

Extension 203mm length, angled

Mirror 64mm dia, adjustable ball & socketjoint

Mirror 38mm dia, adjustable ball & socketjoint

Recovery Magnet

KITCONTENTSANDSPECIFICATIONS:

Handtorch Right angle, 2 C cell (2 per kit)

Handlamp Fluorescent, 12w, socket for endoscope

Endoscope 10w lamp, 9.65mm dia, 350mm, sideviewing

Mirror Arms:

With Torch, 500mm, 45 mirror angle, 2 D cell

Telescopic, 1400mm open, 350mm closed

The following light probes fit the battery handle:

Lampholder Converts battery handle to torch

Magnifier x 8 with lamp

Light Probe 2mm dia, 150mm length

Mirror Sleeve 4.5mm dia. mirror, fits 2mm light probe





Light Probe 8mm dia, 254mm length, right angled,rigid

Light Probe 14mm dia, 380mm length, straight, rigid

Light Probe 14mm dia, 380mm length, flex & stay

Light Probe 14mm dia, 380mm length, safety, acrylic

NATOSTOCKNO:

NSN 1385-99-052-2484




EXPLOSIVE ORDNANCE RECONNAISSANCE

& DISPOSAL

Enhanced Hook & Line Set for the Reconnaissance and Disposal of Improvised Explosive

Devices.

MK II HOOK & LINE SET

An enhanced Hook and Line set that has been refined and updated to a new UK Ministry

of Defence specification. The MKII has been extended to include a range of new

components for dealing with the wide variety of improvised explosive devices now

encountered. The comprehensive set includes two 120 m lines to provide action at a

distance, devices for attaching the line to all types of object, and components for changing

the direction of the line to give lift, avoid obstacles or gain safe cover.

With a cantilever gripping actionthe Allen grip is ideal for movingsoft objects such as carpets.

The wide range of componentsmake the MKII more effective insearching booby trappedvehicles.




HAL 2/01 1 Case

Constructed in 14 SWG aluminium, Hinged lid with toggle latchesInternal compartments Carrying handles on front and both sidesMax. dims incl. fittings: 135mm (height) x 520mm (width) x 300mm(depth).

HAL 2/02 2 Reel Assembly

Reel diameter 300mm. Self-supporting. Fitted with locking brake.Secondary self-adjusting anti-runout brake and rewind handle.Max.dims incl.Handles:350mm(height)x300mm(width)x175mm(depth).

HAL 2/03 1 Main Line

White. Polyamide (Kevlar) rope Diameter 5.5mm. Length 120m.Spliced to swivel snap hook , Stretch approx.. 1 % at 30% full load.Breaking strength of rope 760kg (min.), splice 390kg (typical).Snap hook 100kg (typical).

HAL 2/04 1 Main line

Black. As HAL 2103.

HAL 2/05 2 Treble Hook

Sharply pointed, treble tang, barbed hook with split ring eye.

HAL 2/06 2 Rope Strop

Diameter 3mm. Length 2m. Breaking Strength 248kg incl. splice.Pre-stretched polyester rope strop. Soft eye each end formedwith talurit splice.


Diameter 4mm. Length 2m. Breaking Strength 396kg incl. splice.As HAL 2/06.


Diameter 5mm. Length 2m. Breaking Strength 550kg incl. splice.As HAL 2/06.

HAL 2/09 2 Wire Strop

Diameter 1.5mm. Length 2m. Breaking strength 173kg incl. splice.Galvanised steel wire strop. Soft eye at one end, thimble eye atother end. Talurit spliced.


Diameter 2mm. Length 2m. Breaking strength 340kg incl. splice.As HAL 2/09.


Diameter 3mm. Length 2m. Breaking strength 538kg incl. splice.As HAL 2/09.

HAL 2/12 2 Piton

No.1piton (Short thin form,60mmshaft)Nickelchromemolybdanumsteel. Strong and re-usable.

HAL 2/13 2 Piton

No. 2 piton (long thin form, 80mm shaft). As HAL 2/12.

HAL 2/14 2 Piton

No. 4 piton (Long thin form, 80mm shaft) As HAL 2/12.

HAL 2/15 2 Piton

No. 7 piton (Extra long thin form, 100mm shaft) As HAL 2/12.

HAL 2/16 2 Karabiner

Carbon spring steel karabiner. Zinc plated. Offset. 'D' screwgate. Diameter 11 mm. Max. load 3000kg.

HAL 2/17 2 Allen Grip

Steel. sharply toothed crocodile jaw grip of modular constructionfor gripping soft objects Cantilever operation ensures jawsremain closed when under tension. Stainless steel wire belay forconnection to other HAL components. Recommended max.

working load 25kg.

HAL 2/18 1 Suction Pads

Double suction pad anchor. Vacuum action device for anchoringsmooth surfaces. Twin rubber suction pads, diameter 120mmeach. Alloy body.

HAL 2/19 1 Suction Pad

Single suction pad anchor. As HAL 2/18, but single suction padwith steel back .

HAL 2/20 3 Shock Cord

Length 2m. Diameter 10mm. Elastic rope with steel hook at eachend.


Length 1m. Diameter 10mm. As HAL 2/20.


Length2m. Diameter12mm. AsHAL2/20.2m. Diameter12mm.HAL2/20.HAL 2/23 3 Shock Cord

Length 1m. Diameter 12mm. As HAL 2/20.

HAL 2/24 2 Seizures

Stainless steel locking seizures.

HAL 2/25 2 Vice Jaw Grip

Adapted vice jaw grip fitted with locating eye. Length 180mm (7inches).

HAL 07 4 Snatch Block

Spring-loaded snatch block of stainless steel and Tufnolconstruction to allow the line to be passed through withoutfouling. Provides lifting or line-turning facilities. Sheaf diameter44mm. Closing the spring-loaded head automatically locks theline. Can be used in multiples to give a mechanical advantage ofup to 4" (see Instruction Manual). Proof test load 600kg.

HAL 10 2 Single Hook

Single tang, plain hook. Diameter 12mm. Stainless steel hooksilver soldered onto brass mount with male thread (3/8 inch BSF)Nylon covering over hook.

HAL 11 2 Single Hook

Single tang, plain hook. Diameter 25mm. As HAL 10.

HAL 16 2 Double Hook

Double tang, plain hook. Diameter 25mm. As HAL 10. Angledat 35 degrees to give a semi-grapnel effect.

HAL 17 2 Double Hook

Double tang, barbed hook. Diameter 25mm. As HAL10. Angled

at 35 degrees to give a semi-grapnel effect.

HAL 18 5 Ring

Stainless steel ring silver soldered onto brass screw mount withfemale thread (3/8 Inch BSF). Diameter 25mm. Nylon coveringover ring. Used in conjunction with the hooks.

HAL 2/26 1 Instruction Manual

HAL 2/00 1 Complete EOR Hook and Line Set

Max. dim.:Case: 135mm (height) x 520mm (width) x 300mm (depth).Reels (two off case): 360mm (height) x 300mm (width) x 175mm(depth).Max. weight:Case (Incl. components) 14kg.

Reels (Incl. main line) 6kg each. Total Set: 26kg.

# Per

Set

Item and

Description

# Per

Set

Item and

Description




MINISCAN DESKTOP MAIL SCREENING SYSTEM

The MINISCAN letter and small package X-ray security screening system is a compact,

lightweight unit designed for desktop operation.

The 80KVP, 3mA X-ray source is powerful enough to penetrate bundles of mail and smallpackages, and detail as small as 36 gauge solid copper wire can be detected on the 12" (305 mm)by 16" (406 mm) fluorescent screen. Over 300 pieces per hour can be screened.

SPECIFICATIONS

Inspection Chamber Size: 254 x 533 x 355 mm

Output: 3mA at 80KVP

Definition: AWG 36 Copper Wire

Fluoroscope Screen: 305 x 406 mm

Power Requirements: 110 - 130V single phase AC, 50/60 Hz 2.5 Amperes Max

210 - 230V single phase AC, 50/60 Hz 1 Ampere Max

Weight: 117 Kg

Cooling: Oil Insulated Air Cooled

Radiation Safety: Meets all international standards for Cabinet X-ray System (lessthan 0.5R/hr radiation leakage at 5 cm from any surface.

Overall Size: 1,040 (h) x 599 (w) x 508 (d) mm

Viewing Mode: Direct (TV optional)

Inspection Rate: In excess of 300 pieces per hour

The MINISCAN is completely radiationsafe and may be used in an officeenvironment. Astandardelectricalwallsocket is all that is required. It is ideallysuited for use in government officesand buildings, embassies or consu-lates, company mailrooms and pris-ons.

Television viewing via a 17" monitor isoptionally available at extra cost.

FEATURES

? Lockable Power Switch

? Thermal Overload Protection

? Dual Safety Interlocks

? Optional Television Viewer

? Optional X-ray Foot Switch




Postal bombs, whether real or imagined, are an ever-present problem, not only to targeted

people, but also to ordinary staff handling the mail.

Identifying suspicious items in the mail is vital, but even when this is successfully done, there stillremains the problem of how to minimise the danger to personnel and property. The Suspect PostalBomb Container is the most cost-effective product that has been specially developed for thispurpose. The container is designed so as to retain any suspicious item of mail in an uprightposition. An internally fitted net holds the item in such a position that removal, X-Ray and controlledexplosion all remain viable options to explosive ordnance disposal staff.

The container is made of special glass re-enforce plastic material with additional fire resistantresin, and is large enough to accommodate a briefcase. Blast will be directed upwards and anexplosion device of up to 0.5 kg can be absorbed, which is more explosive material than any otherpostal bomb container that is available today can absorb. Most explosive devices that have beendiscovered so far have contained at least 0.5 kg of explosive material.

SPECIFICATIONS

Height: 900mm

Outside Diameter: 493mm

Thickness: 18/19 mm

Weight: 50kg

V 50: 480m/sec

Colour: Matt Black

Service Life: 10 years (minimum)




The MSI8 EOD Bomb Disposal Suit is a new, state-of-the-art, up-armoured version of the

MSI6 Bomb Disposal Suit which has been in use for many years in dozens of countries

worldwide. The MSI8 provides the highest level of protection of any bomb suit currently

manufactured, whilst at the same time offering maximum comfort and flexibility to the

operator.

The ballistic levels and materials used in the various components of the MSI8 EOD Bomb

Disposal Suit are tested and evaluated to the full quality assurance standard laid down by theappropriate Government organisations.

The suit consists of the following separate items which collectively make the completed garment.

MSI8 EOD BOMB DISPOSAL SUIT

MATERIALS

Helmet

GRP skin with elastomeric aramid core and inner liningIntegrated microphone & earpieceAmbient sound facilityAir cooling fanHelmet-mounted torch with rechargeable batteriesAnti-ballistichardenedacrylic/polycarbonate laminatevisorAluminium carry case supplied

Jacket & Trousers

Ballistic Inserts: Multi-layer,water-repellentKevlar129 HT stitched for an enhancedprotection level

Outer Cover: Fire-retardant cotton (Nomex III)Colour: Navy Blue or Military GreenProprietary: Armouredsteelplateswithclosed

cell, linear foam.

Blast Plates Armoured Steel

All the ballistic inserts used in the MSI8 EOD Bomb Disposal Suit are made of waterproof-treatedKevlar HT which are enclosed in a special water-resistant and anti-ultraviolet membrane. Theoutercover ismadeof flame-retardant NOMEXIII. Inhotandhumidcountries the MSI8EODBomb

Disposal Suit can be supplied in conjunction with the MSI Cooling Suit.

NATOSTOCK NO:

NSN 8470-99-990-0090

? Jacket with attached collar? Spinal Protector? Neck Protector Plate? Chest Protector Plate? Carrying Bag

? Trousers? Separate overshoes? Helmet with visor, air cooling fan and

aluminium carrying case? Groin Protector Plate




ARMOURED EOD HELMET

The EOD helmet is made of a GRP skin with an elastomeric aramid core and is fully adjustableto various sizes for perfect fit by means of the three point suspension and the removable spacerpads that Velcro to the inside. The facility for a communication set consisting of a headphone andmicrophone, plus extension lead for attachment to any VHF radio transceiver, can be incorporatedif required. An alternative communications system comprising a headset, microphone, 100metres of cable and amplifier, for communication between the operator and his controller, can alsobe supplied. Also incorporated in the helmet is an air ventilation system which directs the flow offorced fresh air over the top of the helmet liner, across the visor and down over the operator's faceensuring efficient demisting and clear view. The addition of an anti-blast neck-guard to the bottomfront of the Helmet closes any possible frontal gap between Helmet and Collar.

JACKET

The Jacket is a long-sleeved, side opening design filled with flexible Kevlar armour. Provision ismade on the front for the attachment of rigid chest and groin blast plates by means of integralpockets with webbing securing straps. The high collar provides overlap protection to the helmet,visor and neck-guard. Immediate removal of the Jacket is achieved by use of the quick-releasestraps attached to the side and shoulder.

TROUSERS

The Trousers have fully adjustable supporting braces and wide Velcro waistband catering forsmall, medium and large sizes. Affixed to the front of the trousers is a flexible groin protectorretained in position by Velcro and elastic. At the rear of the legs a full length Velcro strip is usedin conjunction with the retaining straps to fix the articulated flexible armour in position.

SPECIFICATIONS

Outer Cover: NomexIIIInsert: Du-PontKevlar129HTmulti layerSpinal Protector

Neck Protector

Suit: 600m/s (without armoured blast plates).Weight of suit: Approx 26kg with steel blast plate.

Approx. 15kg without blast plates.Armoured

BlastPlates: 1400 m/s (groin, chest and neck).Power Pack: 12v DC auxiliary output socket to power

optional accessories such as helmet -mounted video camera or torch. MainsAC and 12v DC provides 90% rechargewithin 15mins.

Helmet: 4.7kgLevel: STANAGNATO2920Helmet: 600 m/sHelmet Visor: 740m/sAnti-ballistichardened

acrylic/polycarbonate laminate.Helmet Compatible with anyCommunicator:communicationssystem- radio

orhard-wired.Air Blower: 200 litres per minute minimum,

3 speed, can accommodate anNBC canister.




MSI COOLING SUIT

The MSI Cooling Suit is designed to offer a safe and cool environment for people who

must maintain a high level of efficiency and concentration under extreme heat. The

systemis ideallysuitedforpersons involved inbombdisposalandsurveillanceoperations,

as well as personnel in non-air-conditioned armoured vehicles, firefighters, mine workers,

etc.

The MSI Cooling System uses ice water to remove body heat produced during strenuous work,especially in hot environments.

Made from fire retardant Kermel material. The MSI Cooling Suit also offers protection againstheatand flash fireballs. Testingof thesuit on theeffectsofover-pressure, fragmentation,ballistics,body impact and heat have shown this suit is suitable for use under bomb suits, chemical suits andmany other applications where body heat removal is desirable.

The MSI Cooling Suit comprises of a one piece garment covering the upper body upper armsand legs, as well as a close fitting open faced hood for head, a cooling pump and pouch, two waterbottles, battery pack and carrying bag. One size fits all.

Specifications:

Performance:

HeatRemovalRate: 270 watts (full suit)Endurancemin. 45 min at 35°C (95°F)

Cooling Unit:

Control: On/Off/FlowratecontrolPump: 12vColdSource: Solid Ice and waterPower: 12v from suit power supply

Weights:

Suit: 1.0 kgCooling Unit Dry: 0.5kgIce 1.5kgWater: 0.5kgPump Unit: 1.0kg

Material:

Garment: Kermel stretch knit flame retardent fabric,

Compatibility:

? Worn next to skin under any clothing? Cooling unit can attach to bomb suit via harness? Second water/ice bottle supplied for stand-by

NATOSTOCK NO:

8415-99-495-6156




EDU EXPLOSIVE DISRUPTION/DISPOSAL SHIELD

The EDU shield has been developed for use by explosive disposal and tactical teams.

Years of research and attention to detail have produced shield systems that combine high

protective capability and superb manoeuvrability. The EDU shield is now in use in manycountries throughout the world.

Developed to offer maximum over pressure and fragmentation protection during explosivedisposal operations. The EDU is equipped with removable spring-loaded legs. In the stowedposition, the legs hug the edge of the shield for easy storage and manoeuvrability. One easy motionreleases the support legs into the deployed position, allowing the shield to be self-supporting.

SPECIFICATIONS:

Materials: The shield is constructed of a multiplelayer compression moulded Kevlarcomposite laminate. Ballistic visor ismade of Lexan.

Ballistic Protection: V-50 rating using NATO STANAG 2920test specifications.Shield only: 555m/s; Shield with cover:630m/s.Ballistic protection rating againstfirearms available on request.

Overpressure Protection: Offers superior protection against blastoverpressure, results available uponrequest.

Impact Attenuation: Forehead and forearm impactattenuating ethafoam pads are builtinto the inside surface of the shields.These are designed to absorb shockfrom fragment/bullet and pressure waveimpacts.

Dimensions: 130 cm high x 76 cm wide

Component Weights: Basic shield: 13.5kgSpring loaded legs: 1.6kgOptional shoulder harness: 1.0 kgOptional outer ballistic cover: 4.0 kgOptional edge shrouds: 2.5 kg

Outer Cover: The optional add-on cover is composed of Kevlar enclosed in a tough nylonsleeve. Backed by the basic shield, it is designed to boost ballistic and fragmentcapture capabilities.

Handles: The shield includes interchangeable handles (hand and forearm) to facilitate leftor right handed approaches, or a vertical mounted strap and foldaway handlesystem. Other handle configurations are available.

Optional Edge Shroud: The edge shroud is made of flexible loose Kevlar allowing the otherwise hardshield edge to conform to odd-shaped vertical surfaces (walls etc.)

Colour: Standard matt black (custom colours available on request).

NATO STOCK NO:

NSN 1385-99-940-6443




ELECTRONIC STETHOSCOPE

The Electronic Stethoscope has been designed to detecting very weak sound waves,

such as mechanical timing devices and similar mechanisms, that can indicate the pres-

ence of an improvised explosive or incendiary device. It will detect sounds through solid

materials, such as walls, bricks, glass, packing materials, wood etc.

The ruggedised, portable, battery-operated kit comprises both contact and non-contact sensors.It's high frequency and very sensitive, impact contactless search head and amplifier, has beendesigned to filter out interference from extraneous environmental airborne sounds, and so can beused in noisy surroundings. It will detect weak sounds from a distance of approximately 8 metres,depending on the position, surroundings and type of timing device.

The system is provided complete with the following items:

? Electronicscasingwith inbuilt batterycompartment, adjusters for gain andfilter, socket for headset, socket forsensor

? Nicad battery, rechargeable 9 volts

? Dry battery 9 volts IEC No 6 LR61

? Charger unit

? Carrying strap for electronics box

? Special headset

? Set of protective covers for headset

? Weatherproof impact sound sensor

? Coax connection cables, 1 x long, 1x short

? Contact cap

? Contact needle

? Transit case

? Operation and service manual

SPECIFICATIONS

Weight: 2Kg

Amplification: 115dB at 4kHz (approx)

Temperature range: -15° to + 55°C

NATOSTOCK NO:

1385-12-319-0402




INSPECTION MIRRORS

VSM VEHICLE SEARCH MIRROR

The VSM has been developed for security personnel who need to

perform rapid but thorough searches of all types of vehicles. It is now

widely used by defence and security establishments, and also at

civilian locations where high security is important.

? Robust? Exceptional lightness? Maximum visibility and brightness? Virtuallyunbreakableconvexmirror? Rechargeable 12V battery pack option

TUM TROLLEY VEHICLE SEARCH MIRROR

The TUM Trolley Search Mirror is a robust 'wheeled

trolley' under vehicle illuminated search mirror,

complete with a rechargeable battery, specifically

designed for security personnel.

TheTUMhas300mmdiameterconvexwideanglemirrorwhich ismountedona tough,milled-steelwheeledbase.The mirror is illuminated by a 12 volt 6 watt fluorescentlamp.

The 'T' handle which assists in tilting the mirror istelescopicand foldsacross thebasewhennot inuse. TheTUM is easily carried in one hand with the handle folded.

ILLUMINATED TELESCOPIC INSPECTION

MIRROR

VM/BD2 SEARCH MIRROR

The VM/BD2 is a ruggedly designed illuminated

inspection mirror, mounted on castors, used for

searching the underside of vehicles. The large

convex mirror has a wide field of view and is

illuminated by an efficient fluorescent lamp.

The VM/BD2 is widely used by the BritishArmy as wellas by military and security units in many countriesworldwide. Power is supplied from an integral 'D' cellbattery pack, protected within a tough, splash-proofacrylic case, or an external 12V source such as a carbattery. The handle folds for storage.

This mirror is probablythe most widely usedsearch mirror forpeopleto search under theirvehicles for possible carbombs.

? Powerful rubber torch? Extends from approx. 18"

- 5' 5"? 5.5" Stainless steel mirror? Interchangeablemirror




BOMB SUPPRESSION BLANKET & SAFETY CIRCLE

Should the bomb explode, the Safety Circle can help to direct the force of the bomb's explosionupwards, then the Bomb Blanket flexes and contains most of the bomb fragments. Two or moreSafety Circles can be used together to contain larger bomb devices.

The lightweight, highly protective equipment is made of multiple-layer ballistic material and foldsup into a compact, easily carried bag.

? Size: 1.5 x 2.0 metres

? Weight: Approximately 13.5 kg

? Protection Level: V50 17 grain steel fragment @ 400 m/s

? Different sizes and protection levels can be made to order.

The MSI Bomb Blanket and Safety Circle is the most cost-effective and easy to use

equipment currently available for containing fragments and shrapnel from explosive

devices. It is in use byArmed Forces and Police units, as well as many large government

and corporate offices, in many countries worldwide.

The Bomb Blanket & Safety Circle has been designed for use by both unskilled personnel aswell as by skilled Explosive Ordnance Disposal (EOD) operators when confronted with asuspect explosive device in a public area. The Safety Circle is placed around the suspect bomband then the Bomb Blanket, which has four heavy-duty webbing carrying handles, is carefullyplaced over the Safety Circle surrounding the bomb. This eliminates any direct contact with thebomb and provides a safe environment for it's examination and disposal.

NATO STOCK NO:

NSN 4240-99-811-9508




The AD10-2 Hand-Held Metal Detector has been designed for tough environment and

constantusesituationssuchasAirportandpolicingapplications. Thedetector incorporates

solid state electronics throughout, with the exception of our new minimum pressure push-

button on/off micro switch which has a mechanical life of at least 10,000,000 operations

(equivalent to 20 years' constant use at a major Airport).

Theelectronicsmodule isa furtherdevelopmentof theprovenTARGET12hermeticallysealedunitwhich has been in full scale production for 3 years and is now operational in more than 100countries. TheAD10-2 model is backed by 30 years of experience in the design and manufactureof metal detection equipment and incorporates Linear Detection Technology enabling all metals,ferrous, non-ferrous and stainless steel to be detected in any angle or plane.

AD10-2 HAND-HELD METAL DETECTOR

Specification details of AD10-2

Sensitivity: Target size down to 0.10gDimensions: L.362mm x W55mm x H30mmWeight: 262g (operational weight including battery)

General Purpose

? 2 year guarantee? Single push-button operation? Instant response to all metals? No false alarms - No metal present, no alarm? Clear audible alarm (digital go - no go) combined with visual LED? Battery inserted "cartridge" style - no wires or connectors? Ultra high reliability electronics? All equipment supplied complete with battery - Standard 9V battery? Fully automatic self adjusting circuits? Rugged construction - high impact resistant ABS moulded case? All weather use - working temperature -20C +65C? CE Approved? Absolutely harmless to heart pacemakers, defibrillators and pregnant women

NATO STOCK NO:

NSN 6695-99-814-9664




AD18 HAND-HELD METAL DETECTORThe AD18 Hand Held Metal Detector is claimed to be the most sensitive hand-held metal

detector currently in production. As such this UK-developed unit is currently being

supplied under contract to the Federal Bureau of Prisons in the USA and is specified for

use by many other government organisations around the world.

The AD18 incorporatesLinearDetectionTechnology,whichenablesallmetals, includingstainlesssteel, to be detected at any angle or plane. It is particularly effective for locating tiny metal objectsthat may have been concealed, or even ingested within body cavities, with pinpoint accuracy.

The AD18 has the ability to be a fully adjustable detector to allow ‘maximum find capability’. It alsofeatures a two-position rocker switch or 'Turbo Control' to the left of the on/off switch. In the forwardposition this switch enables the operator to fully adjust the detectors’ sensitivity by turning the‘Turbo’, or sensitivity adjustment, knob. The operator can then conduct a super high sensitivitysearch sweep of the subject. However, when the operator wishes to continue the search to thelower leg and foot area,he/shesimplyswitches the ‘Turbo Control’ to the back position. This allowsthe AD18 to eliminate large amounts of static metal in flooring ( i.e re-bar or steel beams), wallsand ceiling, while still being able to detect, for example a hand cuff key or small piece of razor bladein the stock or shoe area, accurately and reliably.With these kind of features, the AD18 Hand Held Metal Detector has now become the’benchmark’ in super-high sensitivity metal detection and is now the preferred choice of hand-held

metal detector for specialised applications.

? Ultra high reliability electronics. Ruggedconstruction high impact resistant case.

? Supplied complete with Battery - ready to use

? 2 year warranty

? On/Off minimal pressure push button switch,has a lifetime warranty. Laboratory testshaveprovedaminimumof30,000,000operations, this equates to 60 years ofcontinuous use.

? Dimension:L360mm,W10.5mm(probe),55mm (body), H35mm

? Weight: 280g

? CEApproved

? Simplepush-buttonoperation

? Instant response to all metals

? Auto ranging - automatically adjusts for optimumperformance for any target size

? Clear audible signal (digital go - no go) combinedwith visual LED

? Fully automatic self-adjusting circuits

? Battery inserted "cartridge style" (spring-loadedBerylliumcoppercontacts -nowiresorconnectors)

? Standard 9V battery

? 2 position switch for Normal/Turbo

? Allweatheruse-working temperature -20C+65C

? Absolute harmless to heart pacemakers,defibrillatorsandpregnantwomen

NATO STOCK NO:

NSN 6695-99-842-1850

MSI




SCANNA 10K LETTERBOMB DETECTOR

GENERALSPECIFICATIONS

PowerSupply: Switchable 220V/110V50/60Hz

IntegralBattery: 12V nominal DCInternally fused at 4.0A

Direction: The test card supplied shall be detected at a faster and slower rate than that normally deployedin mail screening operation.

BackupOperation: Integral battery supplies power in event of main power failure. In the unlikely event of componentfailure 'malfunction' lights up on the face panel. Reserve circuitry can simply be switched onfor continuous use and the faulty PCB can easily be removed and sent back for repair orreplacement.

Accessories: Mains leadTest CardOperating Instructions

OperatingTemp: 0 to 40°CDimensions: 40cm(l) x 45cm(w) x 22cm(h)Weight: 8 kg

Regrettably,bombattacksbyterrorists,extremistsandbyspecial-interestgroupsarenowanalmost

daily occurrence throughout the world. Letterbombs, often concealed in packages no larger than

a book or video cassette, can have devastating effects. Unfortunately they can be difficult to

recognise in amongst normal mail.

Why let employees take the risk of opening unscreened mail when the cost of protection against thesepotentially lethaldevices isnowsurprisingly low? ThenewSCANMAIL10K providessuchprotectionandyetprobably costs less than most other office and mailroom equipment.

SCANMAIL10K isanewgenerationmicroprocessor-controlledmailscreenerwhichwill reliablyscreenallmailand courier deliveries up to about telephone directory size.

Itwill detectvirtuallyall known letterbombdetonationdevices regardlessof the typeofexplosiveused,whetherplastic or otherwise. SCANMAIL 10K is specifically programmed to automatically alarm on packagescontainingpotentiallydangerouscontents, suchasexplosivedevices,whilst reliably ignoring thenormalofficestationary items contained in the mail such as paperclips, staples and metal tags.

This high level of selectivity is achieved without any loss of the forensic standard protection it provides. Thesensitivity level is set at the factory and cannot be reduced by users. A special test card is supplied to allowcustomers to check the correct functioning of the unit each time it is switched on. In this way there is no falsesense of security.

SCANMAIL 10K employs simple touchpad operation and requires no specialisttraining. It will run off an ordinary mainssocket and also incorporates its owninternal battery should your mains powerfail. The unit is completely portable andtakes up as little valuable desk space asnormalofficeprintersofmailroomscales.Inaddition, it iscompletelysafe touseanddoes not damage camera film, magnetictape nor computer disks.

? Fast, safe and cost effective? Excellent discrimination? No special training required? Reliable? Easy to use




SYSTEM 5335 CONVEYOR X-RAY SCANNER

The System 5335 is a compact, lightweight and ergonomic conveyor X-ray scanner designed to inspect

briefcases, purses, backpacks, mailbags, trays and parcels. The System 5335 is designed and developed

for the screening of small parcels for mailrooms, prisons, courthouses, government buildings, schools,

hospitals and corporate offices.

The tunnel opening of 21” x 14” (533 x 356 mm) was specifically designed to accommodate the majority

of parcels. The system uses a high-resolution X-Ray detector array for improved image presentation and

increased automatic threat detection. The System 5335 is a pc based system that incorporates latest

electronic technology in an enhanced modular design. The unit utilises a high speed computer that

implements advanced complex algorithms in real-time operation.

FEATURES

• Organic/inorganicmaterial recognition• Edge sharpening• Pseudo color• Variable intensity control• Programmable zoom 2x to 32x• Archiving of images (20,000)• Programmablepenetration levels• 19" color monitor atomic number measurement

TECHNICALSPECIFICATIONS

IMAGING

Sensitivity: 40AWG GuaranteedResolution: 1mm both vertical and horizontalPenetration: 12mmsteelguaranteedContrastSensitivity: At least 20 levels visible as measured by a step wedge, 4096 gray levelImage display: Colour, organic, inorganic, black & white, reverse monochrome, &

pseudocolour




STANDARDFEATURES

Automatic Image Archiving: Up to 20,000 images in a rotating bufferManually save Image: In windows format to view on personal computers or laptopsPrint Image: Any user’s provided printer configurable by Win 2000Dose per inspection: 0.1mR typicalTunnel Opening: 530mm (21") wide by 350mm (14") highConveyor Speed: 0.23m per sec (45’ per min)Power Requirements: 115-125 VAC, 50-60 Hz & 230-240 VAC, 50-60HzDensity Threat Alert: ProgrammableLevelsUPS: Shuts down computer 2 minutes after power failure

X-RAYGENERATOR

Voltage: 100 kVp Constant potential tube operation at 90kVTube Current: 0.7mACooling: Sealed oil bathDutyCycle: 100%Beam Direction: UpwardVerticallyX-RayDetector: 1024 photodiodes in an “L” Shapped configuration

PHYSICALSPECIFICATIONS

Weight: Approximately 350 Kg (770lbs)Shipping Weight: Approximately 400 Kg (880lbs)Overall Height: 123cm(48.5")Overall Width: 76.2cm (30")Overall Length: 212cm (83.4")

Processor

At least a Pentium-IV, 3.0 Ghz with hyperthreading technology, 512MB RAMAdvanced Video Graphics Card with 128MB RAM, 40GB Hard Disk

Video display

19" SVGA high resolution, low radiation, ergonomic, flicker free flat monitor

Health and safety

The System 5335 is certified to be in full compliance with all international radiation safety requirementsand external emissions limits. Typical leakage radiation is less than 0.1 mR/hr compared to a maximumof 0.5 mR/hr permitted.

Film safety

Guaranteed for high-speed films up to ISO1600

Operational standards

Complies with all published international standards.




KAPPA XR5 Real Time Digital X-Ray System

????? 'Real time' examination of suspect objects

????? Software-controlled by laptop computer provided

????? Fully digital system

????? Excellent resolution

????? Fully portable

????? No additional costs for X-ray films and development

????? Kappa ImageBase software with image data base, image processing and

measuring programme (overlay functions)

????? Remote control option available

????? Universal charging set/for X-ray camera/source

The XR5 is a fully portable digital X-ray camera system which enables the examination and

storage of high resolution x-ray images of suspect articles.

The image converter screen is a high resolution X-ray converter foil converting X-ray radiation tovisible light. The X-ray image is guided via a mirror and a lens to the CCD camera. Due to itsintelligent sensor the camera “behaves” like a film. As soon as there is X-ray radiation the camerastarts to expose, stores the image automatically and displays it continuously. The stored imageis available on the laptop for further processing or analyses.

Contrary to a classical X-ray image intensifier tube with a connected video camera, this type ofconstruction has only a slightly lower time resolution and it is actually lighter. It needs no internalhigh voltage and it shows excellent performances for rugged applications.

The resolution is determined by the particle size of the X-ray image converter screen and the sizeand number of pixel of the camera.

With the Kappa XR5 is easily possible to take stereoscopic X-ray images. With the X-ray sourcemounted on a moving table two images are taken, one image from a left position and one from aright position. These images are displayed alternatively on a special monitor and can be watchedas a 3D image with a pair of polarizing glasses.

TECHNICAL DATA

Pick-up area : 225 x 300 mmPick-up device : Interline transfer CCD with

microlensesNumber of pixel : 752 (H) x 582 (V) effectiveResolution : Wire gage 38 AWGIntegrationcontroland control of X-ray pulses : Via RS 232Signal to noise ratio : >50 dB according to IEC 84 (CO)

103Gamma : 0.45TV-standard : CCIR (NTSC on request)Scanning system : 2 : 1 interlaceSignal output : Composite video, 1 Vpp at 75ÙHorizontal frequency : 15625 HzVertical frequency : 50 HzSynchronization : InternalPower supply : 12 V DC, 300 mAStandard equipment : X-ray camera, XR200 X-ray source, cable 50 m, laptop, PCI

interface, XR-control software, Kappa ImageBase software(image data base, image-processing software, measuringand overlay software)

NATOSTOCK NO:

NSN 6635-99-605-8860




PHYSICAL DIMENSIONS INCLUDING BATTERY PACK

Length 12.5 in. (31.75 cm)

Width 4.5 in. (11.5 cm)

Height 7.5 in. (19 cm)

Weight 12 lbs. (5.5 Kg)

X-RAYLEAKAGE

10 mR per 100 pulses maximum on the side of the unit, 3 inches from the centre of the unit.3mR per 100 pulses 2 inches behind the unit.

X-RAY OUTPUT

X-ray dose per pulse: 2.5 mill roentgens at 12 inches from front of unitNumber of pulses per exposure: 1 to 99

Number of pulses per battery charge: 4000

Number of pulses per second 10 (nominal)

Expected life of XR200: 100,000 pulses

X-ray sources size: 1/8 in. (3mm)

Maximumphotonenergy: 150 KVP

X-ray pulse width: 60 nanoseconds

ELECTRICAL AND THERMAL CHARACTERISTICS

Battery voltage 14.4 voltsBattery type Nickel CadmiumBattery recharge time 1 hourBattery charger DeWalt 14.4 volt 1 hour charger(May be purchased in the user’s country for proper AC voltage interface)Temperature range -10 to 120 degrees F

(-23 to 50 degrees C)Maximum duty cycle 200 pulses every 5 minutes(3600 pulses per hour)Warm-up None required




PASSEX 100M PORTABLE WALK-THROUGH METAL

DETECTOR

The new Passex 100M portable walk-through metal detection system is a sensitive metal

detector for screening persons entering security areas. It detects dangerous metal items

such as knives and pistols even if hidden in shoes. The Passex 100M is a mobile, rugged,

walk-through detector gate designed for use in adverse working conditions or at restricted

sites.

? Portable and lightweight? Weatherproof high grade steel construction? Rechargeable battery? No interference to heart pacemakers and magnetic recording material? Adjustable sensitivity setting? Automatic person counter

The Passex 100M is made of weather-resistant high grade steel components and operates onbatterypoweredelectronics, thusallowinguseoutdoors forseveralhoursofoperation independentof 220V mains.

Mode of Action

Aweakalternatingcurrent is induced into thegate,whichgeneratesamagnetic fieldof lowstrengtharound it. Metal objects carried through this field will cause a drain of energy to the sensor whichis measured and transformed by the Passex 100M's electronics into an alarm signal. This alarmsensitivity can be gradually adjusted. The device is equipped with an automatic signal adaptor toensure a reliable and secure sensitivity calibration for extended use. The detector is activated assoon as a person enters the sensor area, thus reducing the risk of false alarms from movingmasses of metal such as reinforced doors when close to the gate. The detector gate is equippedwith a person counter.

Technical Data - Dimensions

Gate: 2070 x 750 x 580 mmElectronics Box: 90 x 90 x 450 mmPacking: 1250 x 680 x 450 mm

Weight: 10 kgs with electronicsRechargeable Battery: 12V 1,3AhOperation Time: Permanently on mains with rechargeable battery 25 hoursCharging Time: 10 hoursCharger: Lead gel charger 0,5AMains Operation: By buffered battery

Control and Operating Elements

LED red / green: Battery controlLED red: Visual alarmSensitivity: Stepless adjusterAlarm device: 85 dBVolume: Stepless adjustable with On/Off switchSwitch: ON/OFFConnector: Potential free




MSI SEARCH SUITThe Search Suit has been designed specifically for personnel involved in searching for

and clearing of mines and terrorist explosive devices. Although the Search Suit does not

offer the higher protection of the MSI8 EOD Bomb Disposal Suit, it is much lighter in

weight, provides all-round protection, whilst at the same time being comfortable to wear

and allowing virtually unrestricted movement.

The outer material of the Search Suit is constructed of fire-retardant Nomex 111 and includes thelatest Kevlar new technology fibres.

The Search Suit contains a pocket into which an armoured plate can be inserted. The steel plateis an optional extra.

COMPONENTS:

Arms: Separate adjustable sleeves provide optimum movementJacket: Provides front, back, side, shoulder and neck protection, with the addition of

up-armouring pockets for inserting optional ceramic or armoured steelplates.

Groin Protector: Removable insert.Trousers: The unique design provides freedom of movement and optimum protection

to the legs.Helmet & Visor: These, in conjunction with the search suit's high collar, provide maximum

protection.

BALLISTIC SPECIFICATIONS:

Arms, jacket, groin protector & trousers:

V50 (17 grain FSP) STANAG 2920 - 475m/s

Helmet: V50 (17 grain FSP) STANAG - 450m/s

Visor: Acrylic/polycarbonate:V50 (17 grain FSP) STANAG 2920 - 450m/s

Colour: Navy blue or olive green.




The Interscope is a portable endoscope for searching inaccessible areas of buildings,

shipsandvehicles. Therobust fixed focusendoscopecanbeused to inspect cavities andhollow structures internally through holes and gaps of 12mm diameter, with illumination

provided by a bright 10 watt lamp protected within the tip. The endoscope is supplied with

a lightweight battery pack, which provides 3 hours' plus continuous use when fullycharged, and a combined charger/AC power unit.

The Interscope allows the rapid internal inspection of cavities through a hole of only 12mmdiameter. The powerful lamp protected within the tip of theInterscope provides bright illuminationfor searching dark areas.

** Interscope: 12 mm diameter, side viewing only, portable **

INTERSCOPE SEARCH ENDOSCOPE

Specifications

Weight: Complete kit with carrying case - 4 kgBattery: Rechargeable lead/acid battery 12V, 2 -

3AhCase: Leatherette case with belt clipSocket: 4-pin XLR socketPower: Charger/AC power unit

Output 12V DCInput 110/120 or 220/240V AC

Endoscope: 12.0mm outside diameter360mm longWorking length 280mm30 degree field of view10 watt quartz halogen lampin tipStainless steel construction1 metre power lead4-pin XLR connector

Spares: Replacement lamp, 10 watt,12V, quartz halogen




TELESCOPICMANIPULATOR

Claw/Hand 1kgManipulator Pole & Claw 9.5kgCounterweight 8kgTotal Weight 17.5kg

LENGTH

Folded: Approx. 1.5m (4' 6")Extended: Approx. 5.8m (19' 0")

MATERIAL

Pole, Claw: High strength aluminium alloyShoulder Strap: NylonwebbingGearing: High strength steel/brass

POWER

Claw powered.

The new Telescopic Manipulator is an up-graded version of the original model, with a

longer reach and the ability to lift and move a larger suspect Improvised Explosive Device

(IED).

The Telescopic Manipulator is manufactured from non-magnetic material and has beenspecifically designed to enable bomb disposal operators to handle explosive devices anddangerous materials from a relatively safe distance. It can be used in conjunction with theExplosive Distruption Shield to provide an even higher level of protection for the operator.

The new model is provided with a manipulator "claw" for grabbing and lifting a suspect article. Theequipment is hand-operated to ensure maximum control and is supplied with a shoulder strap,together with an adjustable counterweight. It is designed to help the operator to lift an article

NATOSTOCK NO:

NSN 1385-99-936-3585




TERRIER ROBOT EOD VEHICLE

Terrier is a small, lightweight, low cost, tracked vehicle, that can investigate and disrupt

suspicious objects in a variety of locations. It is remotely controlled through a cable, which

also carries the CCTV signal to the colour monitor located in the operator's hand

controller, or to a larger monitor when greater definition is required. A variety of

attachments can be carried on the operating arm, including a camera, grab / manipulator,

portable x-ray generator or a recoilless disruptor.

Terrier is highly manoeuvrable and can climb steps, kerbs and most stairs. It is small enough tooperate inside buildings and down aisles of aircraft, trains and coaches. It is battery powered andhas an endurance in excess of 1 hour in normal EOD activities.

With a disruptor fitted to its standard arm, it can locate and destroy devices from ground level(including those under cars) up to a height of 1 metre. With the aid of a quickly attachable extensionarm, Terrier can operate at heights up to 2.1 metres, and deal with objects located in the overheadluggage racks of aircraft.

The Terrier and all itssupporting equipmentcan be carried in theboot of a car orhatchback. It can bequicklybrought intouseat the operationallocation and is easy to'drive'. Although man-portable, Terrier isstrongly constructedwitha tubular frameandalthough not bombproof, it is well able towithstand the rigoursofbomb disposalactivities.

N.B. Robot vehicles for specialist applications can be made to order.

Technical Specification

Length (with arm retracted): 970 mmWidth: 420 mmHeight (with arm lowered): 420 mmWeight: 36 kgBattery (sealed, maintenance free): 12v 15AhStandard operating cable length: 60 m

CCTV - Colour camera feeding 4" monitor in hand controller, which is fitted with outlet socket foralternative larger monitor.

Terriers are individually produced and modifications or additional features can in many cases beincorporated to suit customer's requirements.

NATO STOCK NO:

NSN 2350-99-974-7377




TERRORISTIMPROVISEDEXPLOSIVETRAININGDEVICES

Audio Cassette Bomb:

This incendiary device is cleverly concealed inside a standardaudio tape cassette and comprises dummy incendiary material,modified flashbulb initiator, powercell,mechanical timer,modifiedslidearmingswitchand twofuelcapsules toenhance the incendiaryeffect.

Book Bomb:

A hollowed out book conceals dummy explosive, electronic detonator,power cell, mechanical delay to a micro-switch arming device, with adowel safety pin. The device is initiated once the book is opened by thetarget, thus releasing the micro-switch. The device is supplied with abuzzer to simulate detonation.

Video Cassette Bomb:

The video cassette inside a standard presentation case comprisesdummy plastic explosive, electronic detonator, two AA sized batteries,electronic timer unit and an arming slide switch concealed under thefront flap of the tape.

Incendiary Device:

This clear perspex container comprises dummy explosivematerial, flash bulb initiator, PCB long delay timer and armingswitches, batteries and fuel capsules to enhance the incendiaryeffect. The arming warning LED will flash once the armingdevice is initiated.

35mm Camera Bomb:

This explosive device is concealed inside a standard compactcamera with dummy explosive moulded to fit the shape of thecamera. An electric detonator is concealed within a modified filmpack. Once the camera is opened and the film pulled aside a micro-switch is revealed which arms the device once the back of thecamera is closed. All standard functions of the camera, such asflash, shutter, winder, etc. work normally.

Car Bomb:

This type of under vehicle booby trap has been used successfully totarget individuals. The device comprises a mechanical delay to amicro-switch arming device and firing is via an adjustable mercury tiltswitch to an electric detonator. Strong magnets normally enable thedevice to be fitted to the underside of a vehicle.

Radio Cassette:

IED based upon that used to destroy flight PA103 over Lockerbie in 1988.This device consists of approximately 300gms of simulated Semtex-Hexplosive, electric detonator, barometric switch, PP3 cell, arming switch,PCB timer and sound unit to simulate explosion.

Each training device is authentic in every detail to actual terrorist devices and contains

fully functioning electronic and/or mechanical components as well as dummy explosive

material. Each device also provides an accurate X-ray signature which makes it ideal for

all types of EOD and search training. Typical devices include the following:




Environmental

Operates at -17ºc to 50ºc with less than 95% relative humidity.Conforms to NILECJ-STD-0601.00, meets FCC Class AStandards for emissions.

X-Ray Source

Voltage: 160kVp constant potential tubeoperating @ 140kVp

Dutycycle: 100%Cooling: Sealed oil bathBeam orientation: Vertically upwards

SPECIFICATIONS

General

Sensitivity: 36 gauge wire guaranteedSpatial Resolution: 1mm using new ASTM F-792

test bagPenetration: 22mm steel guaranteedContrast Sensitivity: 1T-H4 guaranteed, 4096 gray scale

levelsDose per Inspection: 0.1mR typicalTunnel Opening: 25.6" (w) x 17.7" (h)Power requirements: 115-125 VAC, 60Hz (10 amp max)

230-240 VAC, 50Hz (5 amp max)Conveyor Speed: 0.23 m per sec @ 60Hz

45 feet per minute

ComputerSpecifications:

Minimum configuration: Pentium IV, 3.o GHz,Ram:256 Mb,HDD: 40 GBCD ROM

Video Displays: Dual 19" SVGA highresolution, lowradiation, flicker freeflat monitor

Physical Specifications

Weight: Appr. 450kgsWeight (crated): Appr. 519kgsConstruction: Steel frame on casters

FilmSafety

Guaranteed for high speed films up to ISO 1600

X-Ray Sensor

1280 photo diodes in an "L" shaped configuration

Standard Features

? 2 x 19" Colour Monitors? Programmable penetration levels? Organin and Inorganic imaging? Pseudo colour? Automatic Z measurement? Programmable zoom 2x to 32x? Edge sharpening

SYSTEM 6545 CONVEYOR X-RAY SCANNER

TheSystem6545 isanx-raysecurityscreeningsystemwithacompactdesign,suitable forusewhere

space is limited. Yet with tunnel openings of 45 cm (17.7") high and 65 cm (25.6") wide, the System

6545 is ideal for the screening of briefcases and packages.

The System 6545 is ergonomically designed with operator comfort and ease of operation as a main featureof the system. The System 6545 is a PC based system that can be networked with other inspection systemsandcan transmitdataviaethernetusing theTCP/IPnetworkprotocolsystem. Images fromeachSystem6545

can be sent through a network to a central server PC where the images can be viewed, stored or printed.

TheSystem6545 is ideallysuited forembassiesandmailrooms,governmentbuildings,courtrooms,nuclearpowerstationsandcommercial facilities requiringbriefcaseandpackagescreening. It isalsoequallysuitablefor carry-on baggage screening at airports where floor space may be a consideration.




SPECIFICATIONS

Trailer size:

367cm long x 190cm wideOuter Container size:

100cm high x 100cm wide

Inner Container size:

100cm high x 64cm wideHeight: 142 cm

Steel Thickness: 40mmWeight: 900 kgProtective Level: 4 kg of TNT

SAFEWAY BOMB CONTAINMENT TRAILER SYSTEM

The new SAFEWAY Bomb Containment Trailer System was developed by government Explosive OrdnanceDisposal (EOD) experts to enable relatively inexperienced operators to remove a suspect Improvised ExplosiveDevice (IED) toasafe locationwhere itcansafelybeexaminedordestroyed. Theequipment isdesignedtosafely

contain and transport a suspect explosive object of up to 4Kg of TNT and up to 600mm x 800mm x 600mm in size.The unique design of the Safeway enables it to be easily used with a minimal amount of training.

The Safeway Bomb Containment Trailer System consists of a specially designed bomb container mounted on afour wheeled trailer which can easily be towed. The container is made from two layers of high-strength, high-impact40mmballisticsteel. Thechamberspacebetween the innersteel 'tube'and theoutersteelwall containssand,whichtogether with the strengthened ballistic steel, helps absorb the effects of blast, thus enabling the Safewaycontainerto be used repeatedly.

The Safeway's exceptional thermal and pressure-tolerant design provides high explosion suppression capability.In theeventofanaccidentaldetonation the tubulardesignof thecontainerensures that theblasteffectwill bedirectedvertically upwards, rather than sideways, thus ensuring no damage will be caused to the towing vehicle, trailer bodyand the surrounding area.

A suspect device is picked up with the aid of the hand-portable telescopic manipulator which is provided with theSafeway System. The operator places the device on the back of theSafeway trailer and the rotating hydraulic liftingarm is remotely operated to raise the package and gently place it inside the container.

Once the Safeway is loaded with the suspect device the trailer can be safely towed to a convenient site where thedevice can be removed from the container. Shock absorbers help protect the container from any sudden movement.Removing the suspect device is done by reversing the loading process. Once removed from the Safewaycontainer,the device can be examined with the use of a portable x-ray or it can be harmlessly disposed of with the use of anexplosive disruptor.

Safeway is supplied as a complete system including telescopic manipulator. NATO STOCK NO:NSN1385-99-331-1632




MD8+ MINE AND METAL DETECTOR

The new MD8+ Mine and Metal Detector is an up-graded version of the MD8 which was designed

for use by the British Army and is also now in use with UK Police Forces for search operations. The

instrument is a high sensitivity metal detector based upon very high speed pulse induction

technology and has exceptional performance against minimum metal mines. Because the

equipment is largely automatic in operation, being self adjusting to its immediate environment, it

is very simple to operate with only a minimum of training required.

All elements of the instrument (with the exception of an optionalexternalearphone)havebeen integrated intoasingleunit incorporatinga control unit, batteries and telescopic halo assembly. There are noseparate parts, and consequently no cumbersome interconnectingcables. Theequipment is totallysealed,waterproofandsubmersible.

The instrument is controlled by a microprocessor, which permits veryprecise timing, rapid switching and sophisticated signal processing.This, in conjunction with the novel head design, permits detection ofvery small metallic objects even in the proximity of larger targets.Incorporated are comprehensive and automatic self-diagnosticprocedures controlled by the microprocessor. A user initiated testfacility is also present. The verification of these tests is presented tothe operator by a confidence tone.

Thesearchhead incorporatesdifferentialRxcoilswhichgreatly reduce interference fromexternalsourcessoenhancing the signal/noise ratio and permitting greater sensitivity. This feature also allows objects outsidethe area of the halo to be disregarded. However, the area of desensitisation is controlled so that signals fromthe sides of the search head are accepted. The use of differential coils greatly enhances the ability of theequipment to operate in traditionally hostile conditions, for example over mineralised soils, without loss ofsensitivity.

The halo is divided fore and aft by a 'sighting bar'. When the centre of the target is directly below this bar avery distinct null appears in the audio signal thus permitting the location of the centre of the target to withina few millimetres.

TheMD8+electronics incorporateanautomaticpowersupply thatenables thedetector tobepoweredbyonlythree standard D-cell batteries. The power supply maintains a constant voltage to the electronics, permittingmaximum performance, whatever the state of the batteries, and utilises the full capacity of the cells.

SoftCase (Haversack)

Weight: 3kgTransit Weight: 10 kgOperatingWeight: 2.4kgOperatingLength: Max. 1560 mm Min. 1120 mmMax. useable detection: 0.05 g stainless steel at 75

mmTemperature: -25°C to+70°C(operationand

storage)Environmental: Humidity - fully sealed and

submersible to 2 metres

Halo Probe:

Max. Length: 1120 mmMin. Length: 700 mmWeight: 100 g

NATOSTOCKNO:

NSN6665-99-727-8434

Power Requirements

Batteries: 3 x 'D' drycells IEE LR20. Manganesealkaline

Life: Max sensitivity - 12 hours continuous, 16hours intermittent Med/Low sensitivity -18hourscontinuous,24hours Intermittent

Low Battery: Indicated by two stage flashing LED andaudio tone

Control unit (incorporating batteries)

Length: 470 mmWeight: 1100 g inc. batteriesMicroprocessor: 2 x RISC based 8 BIT

incorporatingADC




STK2 SEARCH TOOL KITThe STK2 is a new tool kit which is designed to assist during search operations conducted by bomb

searchteamsandalsoCustomsoperators. Itcontainsacomprehensiverangeofhandtools toenable

operators to dismantle equipment and machinery, as well as a range of cutters and saws to open

gates and penetrate fences.

When immediate visual inspection behind walls or panelling is required, the STK2 power drill enablesinspection holes to be bored through all types of material and walls up to 250mm thick, allowing rapid internalinspection with an endoscope.

The complete STK2 Search

Tool Kit is supplied in twofitted carrying cases with atotal weight of 40kg.

Cordless drill, 1/2" chuck comprising:

Drill with rechargeable batterySpare rechargeable batteryBattery chargerDrill bit, HSS, 5mm (2)Drill bit, HSS, 10mm (2)Drill bit, HSS, 12mmDrill bit, flat, 9.5mmDrill bit, flat, 13mmDrill bit, flat, 19mmDrill bit, masonry, 10 x 300mm

29 piece, 1/2 inch square drive socket set consisting of:

RatchetSliding 'T' bar125mm extension250mm extensionBall jointAF sockets, sizes: 10, 11, 12, 13, 14, 15, 17, 19, 22, 24, 27,30mmImperial sockets, sizes: 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1, 1 1/16, 1 1/8"

The kit contains the following

equipment:

Leather glovesNylon cord, 150mInsulation tape (2)Steel measuring tape, 3mRetractable knife & spare bladesLinoleum knifeScissors, 250mmPadsaw, with various bladesHacksawHacksaw blades (10)Tack extractorClaw hammer, 1lbClub hammer, 4lbCold chisel, 250mmWrecking bar, 18 x 600mmPliers, combination, 178mmPliers, long nosed, 203mmPliers, side cutting, 152mmPliers, slip joint, 254mmPliers, vice grip, adjustable, 254mmSeizers, 150mm (2)Tweezers, mmCentre punchReleasing fluidScrewdriver, cross head, 150mmScrewdriver, cross head, 180mmScrewdriver, cross head, 215mmScrewdriver, cross head, 265mmScrewdriver, flat head, 150mmScrewdriver, flat head, 230mmScrewdriver, flat head, 335mmWrench set, hexagonal, imperialWrench set, hexagonal, metricWrench, adjustable, 152mmWrench, strap, 50-300mm dia.Cutter, capacity - 0.9mm (20swg) mild steelCutter, capacity - 1.2mm (18swg) mild steelBolt cutter, 610mm, capacity - 8mm HT steel




NON-MAGNETIC MINE PRODDER

The Non-Magnetic Mine Prodder has been designed to locate mines buried in depths of

up to 250mm.

Primarily intended for situations where a magnetic device would activate a mine, the Mine Proddercanalsobeusedwheremagnetic fieldsarenotconsidered important. Designedandmanufacturedto DefStan AQAP1, the Mine Prodder is supplied as a kit fully tested in accordance with Stanag2897, a necessary requirement for all non-magnetic EOD requirements.

The kit consists of a spike holder assembly, handgrip, carrier web and tube assembly.

1 off Spike Holder Assembly NSN W8/1385-99-840-0190

1 off Handgrip NSN W8/1385-99-840-0191

1 off Carrier Web NSN W8/1385-99-840-0192

1 off Tube Assembly NSN W8/1385-99-840-0193

TECHNICAL DATA

Colour

Prodder: NATO GreenHarness: NATO Green

Dimensions

Short assembled length 510mmLong assembled length 1030mmLength (stored in harness) 755mmWeight (prodder) 409gmWeight (stored) 509gmMean diameter (main body) 20.5mmMean diameter (spike) 6.4mmDiameter (spike point) 1.75mmSpike hardness 45/50 Rockwell C




ABL1000 RECOILLESS DE-ARMER DISRUPTOR

TECHNICAL DATA

Disruptor De-Armer

Overall Length: 515mm Overall Length: 284mmWeight: 4.5kg Weight: 3.5kg

Container Weight of Kit: 25kgOverall: 873 x 428 x 187mm

Material: AluminiumColour: NATO Green

Developed as a dual role, De-Armer Disruptor, designed to defeat the threat posed by

more complex, better protected, improvised explosive devices (IED's) and to deal with

unexploded ordnance (UXO), the ABL1000 De-Armer Disruptor remains completely

recoilless during operation. The ABL1000 utilises the standard electrically fired 0.5"

cartridge XLIE 1.

When used as a Disruptor the ABL1000 will be set up close to the suspect device and aimed atthe firing circuit or detonator. On firing it will project a water slug into the device, disrupting the firingcircuit without causing detonation of the device's explosive contents.

As a De-Armer, the ABL1000 will project a variety of steel slugs into the fuses or pistols of airdropped bombs and some land service ammunition. A bolster slug enables it to be used againstother UXO as well as being effective against metal-cased IED's.

The ABL1000 De-Armer Disruptor is a multi-shot device, capable of many firings withoutdistortion. It requires minimum maintenance and can be used for IEDD and EOD PersonnelTraining without detriment to its performance. The ABL1000 can be accurately positioned eitheron its robust, lightweight stand or on its own. When fitted to a remotely operated vehicle (ROV),no damage is caused since the recoil forces are not passed to the vehicle.

The ABL1000 is constructed from anti-corrosion precision-machined parts which are subject tothe most demanding quality control during manufacture. Flow detection tests as detailed inMFD601, then crack-detection and over-proof firing, are carried out before being accepted intoservice.

Training and maintenance are simple and all tools and equipment are supplied. All spare parts andconsumables are contained in the kit. With correct maintenance, barrel life is virtually unlimited.There isnodifferencebetweenaserviceABL1000De-ArmerDisruptorandoneused for training.

The ABL1000 De-Armer Disruptor is supplied as a complete kit, with the exception of the firingcartridges, in a robust shock-tested metal container. Cartridges XLIE1 are supplied in units of 77-off packed in H83 Ammunition Containers.




The SPRscan Surface Penetrating Radar is a revolutionary high performance system

designed for detecting virtually any object concealed under the ground or behind walls.

The equipment is completely weatherproof and can operate in virtually any type of soil

condition. Depth of detection will vary on the object size and type of soil, but is typically

up to 3 metres.

The SPRscan Surface Penetrating Radar System has evolved over a number of years followinga specific request of the British Ministry of Defence for ground penetrating equipment. SPRscan

is now in full production and has a wide variety of applications, including Police and Military searchrequirements, VIP protection, electronic countermeasures as well as commercial surveying. Ithas been instrumental in the Police detecting buried human bodies in UK and Belgium.

The SPRscan radar systems consists of 3 main parts, the controller (which in effect is aruggedised PC personal computer), an antenna, and the TX/RX head electronics unit whichtransmits the information from the antenna to the controller. The standard system is supplied witha 500MHz antenna which has a typical penetration depth of 1.5 to 2.5 metres in good conditions- i.e. where sand and peat are good and salt water and clay are poor. The other antennas in therange are the 250MHz (typical penetration depth of 2.5 to 4.5 metres) and the 1GHz and 2GHzantennas. As a general guide, the lower frequency antennas (250MHz and 500MHz) are normallyused for work below ground and the higher frequency for work above ground. As the penetrationdepth increases the resolution decreases. Hence the 1GHz and 2GHz are very useful for locatingvery small anomalies behind a surface such as a wall.

The radar works by sending out pulses of electromagnetic energy and detecting the electrical echocaused by dielectric differences within the surface being investigated. One of the main featuresof SPRscan is that during a search, as the antenna is moved across a surface the data is shownin real time, in colour, on the controller screen. This means that an anomaly beneath the surfacecan be seen immediately the radar passes over it, thus making instant on-site decisions possible.The data can also be downloaded onto a thermal printer which provides a strip print of the survey,or it can be stored on the hard disk for processing and/or inclusion in a survey report.

SPRscanSURFACEPENETRATINGRADAR

SPRscan is very flexible and can be usedon a harness, mounted on a trolley or handheld if the smaller antennas are being used.It has a very wide range of applicationswhich include the following: locatingutilities,voids, bodies buried beneath the ground,caches of explosives/money/drugs etc.hidden beneath a surface, locatingfoundations in archaeological digs, pipes orcables etc.

The main features of ground penetratingradarare that it isnon-destructive (nodiggingnecessary), it isnon-evasive (everydayworkcan carry on around a radar survey) and itcandetectnon-metallicobjectse.g.plastics,ceramics etc.




MK1 HOOK & LINE KIT

? Robust

? Low stretch Kevlar line, 750kgbreaking strain

? 5000 units in service

? High strength hooks

? In service with the UK and USarmed forces

? Plain and barbed hooks

? Gated high strength snatchblocks

? Comfortable line pulling handles

The MK1 is a basic hook and line kit recommended for clearing explosive ordnance. The

kit was developed in conjunction with British Army bomb disposal teams to provide a

versatile means of remotely moving dangerous objects in a wide variety of locations.

Since then the MK1 has been deployed on active service in many areas of the world and

has become standard issue for in any EOD teams worldwide, with it also being used on

EOD training courses in both the UK and the USA.

The varied components enable a line to be securely fastened to all types of munitions and IED'sto facilitate their movement to improve access for many types of disposal operation.

Alternatively the MK1 kit is often used as a means of 'tumbling' suspect objects when carryingout high-risk searches of hides or 'safe houses' which may be 'booby' trapped.

Main Line. The 150m main line is constructed with a nylon outer sheath and Kevlar® to ensurethat the overall stretch is less than 1% when the line is fully extended. The main line is terminated with aspring gated 'snap' hook for quick connection to a wide range of hooks.

Hooks. 12.5, 25 and 50mm diameter hooks are supplied, with both plain and barbed points forattaching the line securely to soft materials such as holdalls or fertiliser sacks. All hooks areconstructed of non-ferritic stainless steel.

Snatch Blocks. These have a side-opening cheek that allows the line to be loaded or removedfrom the block without having to detach the line from the object being moved. Snatch blocks canbe used for changing the direction of the line or to achieve a mechanical advantage.

Case and Reel. The reel is anchored to the case and is fitted with a locking brake to preventexcessive line run-out. The case is fitted with a number of anchor points with which to tie off themain line or to anchor the case itself to a tree or post. Both the case and reel are constructed ofheavy gauge steel for long service and durability.




EXPLOSIVE ORDNANCE RECONNAISSANCE &

DISPOSAL - MK IV HOOK & LINE SET

The MK4kitprovidesavarietyofcomponents forattachinga line toasuspected IED

and devices for anchoring snatch blocks to floors, walls and windows and door

frames. Snatch blocks are self opening to enable IED's to be manoeuvred along

complex routes in a single operation. The 120m line enables the removal operation

to be conducted remotely.

A sledge is included which can beusedto improvethemanoeuvrabilityof a suspect object on stairs orrough ground and to preventsnagging at corners. A telescopicpole which extends to 3m may beused to attach a hook and lineremotely. All components fit into acompact carrycase and can easilybe carried by one man leaving onehand free.

Kit Contents:

Pole: Telescopic, 3m extendedHook: Single plain tang, 12mm gape male threadHook: Single plain tang, 25mm gape male threadHook: Single plain tang, 50mm gape male threadHook: Double plain tang, 25mm gape male threadHook: Sharp pointed, treble tanged, barbed with eyeHook: 25mm gape, spring gate, fits telescopic poleHook: 50mm gape, spring gate, fits telescopic poleSnatch Block with Jammer CleatScrew Eye: Hand screw into wood (x10)Line Branch: Clamps to 5.5m line, with eye attachmentLine: 5.5m diameter, 120m, 750kg, strength, low stretchReel: 300mm diameter, winding handle, anti runout clutchRing: 25mm diameter, female thread, fits to male thread hooksGrip: Spring action, 25mm maximum gape, 115mm o/a with eyeGrip: Self Grip, adjustable, 25mm maximum jaw gape, 250mm o/a with eyeSnatch Block: Self-opening, maximum load 200 kg, swivel eye (x4)Splitter Ball: Use with self-opening snatch blocks, fits 6mm line (x2)Karabiner: Screw Gate, 15mm gate, 2400kg maximum load (x2)Karabiner: Screw Gate, 23mm gate, 2700kg maximum load (x2)Shackle: 'D' shape, 13mm gate, 1000kg maximum loadPiton: 50mm shaft length, 4 to 9mm shaft thicknessPiton: 70mm shaft length, 1.5 to 6mm maximum shaft thicknessPiton: 70mm shaft length, 4.5 to 10mm maximum shaft thicknessSelf Adhesive Anchor: 75x75mm, with eye (x10)Suction Anchor: Doubler Pad, 118mm pad diameter, eye, 315mm o/aDoorway Anchor: 700 - 1100mm with eyes (x2)Door Stop: Wedger Type, rubber, 120mm o/a (x4)Sledge: Rough terrain, accommodate a items up to 580mm width

Belt Sling: 80x1400mmRope Sling: 3mm diameter, 2m, 240kg strength (x2)Rope Sling: 4mm diameter, 2m, 390kg strength (x2)Rope Sling: 5mm diameter, 2m, 550kg strength (x2)Wire Sling: 1.5mm diameter, 2m, 170kg strength (x2)Wire Sling: 2mm diameter, 2m, 340kg strength (x2)Wire Sling: 3mm diameter, 2m, 530kg strength (x2)Pulling Handle: Grips 5.5m diameter lineTools: Compact Set, pocket knife style

Supplied in a reinforced nylon canvas (cordura) case 980 x 370 x 120mm, with separate reel andline. The line is supplied ready wound onto the reel. Components are also available separately.




The De-Mining Visor enhances the front face protection of a de-miner, or an

explosives expert, working in an environment where there is a possibility of a mine

or explosive device detonating. It will protect the wearer against blast and

fragments.

DE-MINING VISOR

The De-Mining Visor has a cut-out area in the front of the mouth to enable the operator tocommunicate and to reduce fogging up of the visor.

The De-Mining Visor is mounted on a headband.

V50: 258 m/s




EXPLOSIVE ORDNANCE RECONNAISSANCE

& DISPOSAL

HAL MK III HOOK & LINE SET

A heavy duty hook and line kit approved by the UK Ministry of Defence for moving

vehiclesandheavy improvisedexplosivedevices. TheHALMK3hasbeendesigned

for use where the load limitations of the HAL MK1 and the HAL MK2 are likely to be

exceeded.

Components in theHALMK3,whichincludesslings,hooksandshackles,enables the 150 metre line to beattached to a suspect vehicle orcontainerquicklyandsecurelywiththeminimumofdisturbance.

Snatchblocksallow theoperator tochange the direction of the line togain protection or to operate inconfined areas. Ground anchorsenable thesnatchblocks tobeusedwhere there are no naturalanchoragepoints.

Kit Contents

Reel: 460mm diameter, rewindhandle,anti-runoutbrake

Line: 10mm diameter, 150m, 3670kg strength, low stretchWebbing Sling: 50mm wide, 2m woven polyester, eyes both ends, max. load 2000kg (x2)Webbing Sling: 50mm wide, 6m woven polyester, eyes both ends, max. load 2000kg (x2)RoundSling: 1m circumference, polyester, max. load 1000kg (x2)RoundSling: 2m circumference, polyester, max. load 1000kg (x2)RoundSling: 4m circumference, polyester, max. load 1000kg (x2)GroundAnchor: 300mm, galvanised steel, angle section (x2)GroundAnchor: 500mm, galvanised steel, angle section (x2)GroundAnchor: 1m, galvanised steel, angle section (x2)Shackle: Width 32mm, depth 64mm, max. load 3000kg (x4)SnatchBlock: Max. load 2680kg, swivel eye (x2)Hook: 120mm opening, fixed eye (x2)

Supplied in a reinforced canvas case, with separate reel and line. Weight of accessoriesin case: 25kg. Weight of line and reel: 21kg.




RIGID SEARCH ENDOSCOPE KIT

The competitively priced Rigid Endoscope Search Kit has been developed for use by

specialist Police, Customs and military operators for a wide range of applications,

including narcotics and contraband detection, IEDD and EOD.

The Rigid Endoscope's very high quality optics tube is made of extremely rugged stainless steel.It has a diameter of 12mm and a working length of 300mm, with a 90° lateral direction of view anda 30° field of view.

The focus is fully adjustable from 10mm to infinity, and the integral high power fibre optic lightingprovides bright and safe 'cold light' illumination, so there is no hot lamp at the end of theEndoscope's tip.

The 50 watt quartz halogen lightsource couples directly to the endoscope body, and is poweredby a belt mounted battery pack.

Kit consists of:

Knowall Rigid Endoscope:

Rigid Endoscope 12mm diameter by 300mm long stainless steelinsertion tube. 90° direction of view with a 30° field of view.

LH50 Light Handle:

50Wattquartzhalogen, fancooled lighthandlewithSCMI femaleconnection and 1 metre lead to battery pack.

LH50BP Battery Pack:

2.5 Amp/Hour waist mounted battery pack, provides 30 minutescontinuous run time. Push button battery condition indicator.Charges in approximately 13 hours using LH50BPC.

LH50BPC:

240 volt mains input, 12 volt 330mADC output charger with LEDindicators to show when charger is on and when battery is fullycharged.

Carrying Case

Optional Accessories:

ZRA3 Right Angle Viewer:

Addonviewereyepiece togiverightanglepositioning foruser's eye.

CH-CT-CH Lens Adaptor:

Lens adaptor for fitment to front of standard cameralens.

32-END35 Camera Adaptor:

Dedicated focusing lens adaptor to magnify imagedirectly from Endoscope to the camera film plane.




ZNOSE 4200 VAPOUR TRACER & ANALYSER

The state-of-the-art zNose 4200 Vapour Tracer and Analyser is a powerful tool for the

detectionofexplosives,chemicalandbiologicalweapons,narcotics,contraband,hazardous

industrial materials, improvised explosives and flammables. It is the only portable, real-

time analyser that can detect and identify all types of vapours and traces of organic,

biological and chemical compounds accurately and extremely rapidly.

The zNose 4200 Vapour Tracer and Analyser has received validation from both the USEnvironmental Protection Agency and the White House Office of National Drug Control Policy aswell as being recommended for use by The US Homeland Security Task Force as a major tool inthe fightagainst terrorism. It hasevenbeenchosenbyNASAforuse in its space laboratory toassistin the search for extraterrestrial life on other planets!

The electronic nose and vapour analysis technology is based upon SurfaceAcoustic Wave (SAW)sensors and flash chromatography. This highly sophisticated technology allows, for the very firsttime, the fragrance, odour or smell associated with virtually any chemical process or product tobe chemically analysed and quantified with part per billion accuracy within seconds. This ability toanalysecompounds in greatdetail is theprimarydifferencebetween thezNose andaconventionalbomb detector. Conventional bomb detectors are designed to see very narrow bands of material,typically containing nitrogen, such as TNT or RDX, however, the zNose is able to detect thecomplete spectrum of compounds within an aroma or odour, including those that do not containnitrogen, such as TATP. TATP has, until recently, proved almost impossible to detect, explainingwhy it was the terrorists’ explosive of choice during the recent London bombings.

The zNose’s unique software includes an expandable library of over 700 chemical signatures, sothat in the event of a new narcotic or explosive being identified, once profiled, it can be added to thesoftware library keeping the zNose abreast of all known threats.

SPECIFICATIONS

Sensitivity: 10-secondanalysis timewithsensitivity inpartperbillion formostcompounds.Detects hydrocarbons in the range of C4-C25.

Detector: Surface Acoustic Wave (SAW). Quartz Microbalance.Temperature: 0°- 125°C.

Sampling: Internal Sample Pump.Sample Introduction: .5ml/sec.

Carrier Gas: Helium. 300 tests per helium charge.

Weight: 9.1kgSize: 30 x 25 x 15 cm.




MINISCAN 2 DESKTOP MAIL SCREENING SYSTEM

The new Miniscan 2 Mail Screening System is designed for remote inspection of letters

and small packages via the Miniscan 2's inbuilt high definition monochrome CCD camera.

The camera is connected by a six foot cable to a 17" black and white monitor which

provides enlarged images of the article being examined.

The Miniscan 2 letter and small package X-ray security screening system is a compact,lightweightunit designed fordesktopoperation. The80KVP,3mAX-raysource ispowerfulenoughto penetrate bundles of mail and small packages, and detail as small as 36 gauge solid copper wirecan be detected on the 12" (305mm) by 16" (406mm) fluorescent screen. Over 300 pieces perhour can be screened.

The Miniscan 2 is completely radiationsafe and is designed for an office envi-ronment. A standard electrical wallsocket is all that is required to power thesystem. The system is in use withUnited Nations agencies, governmentoffices and buildings, embassies or con-sulates, company mailrooms and pris-ons in many countries worldwide.

FEATURES

? Lockable power switch

? Thermal overload protection

? Dual safety interlocks

? Optional television viewer

? Optional x-ray foot switch

SPECIFICATIONS

Inspection Chamber Size: 254 x 533 x 355 mm

Output: 3mA at 80KVP

Definition: AWG 36 copper wire

Fluoroscope Screen: 305 x 406 mm

Power Requirements: 110 - 130V single phaseAC, 50/60 Hz 2.5Amperes max, 210-230Vsingle phase AC50/60 Hz 1 Ampere max

Weight: 117 Kg

Cooling: Oil insulated air cooled

Radiation Safety: Meets all international standards for cabinet x-ray systems (lessthan 0.5R/hr radiation leakage at 5 cm from any surface

Overall Size: 1040 (h) x 599 (w) x 508 (d) mm

Inspection Rate: In excess of 300 pieces per hour




Training of EOD Personnel can be carried out using theequipment without detriment to its performance. The

Pigstick is positioned using an anti-roll clamp or anoptional lightweight stand to ensure accurate positioning.It can easily fitted to a remote operated vehicle (ROV).Preparation of The Pigstick can be carried out behindcover, or away from the vicinity of the IED to ensureoperator safety.

The Pigstick is constructed from anti-corrosive precision-machined parts which are subject torigid quality control during manufacture. The main body material is subjected to the flaw detectionrequirements of MFD 601 before manufacture and overproof firing, and crack-detection procedureprior to acceptance.

The Pigstick is supplied as a complete kit in a canvas holdall with stitched pockets to secure allthe items detailed below:

? Split sleeve adapter

? Contact cover

? Disrupter main body

? Disrupter rear body

? Water bottle

? Loading tool

? Cleaning brush

? Cleaning rod

? Screwdrivers

? Anti-roll clamp

TECHNICAL DATA

Total Weight of Kit: 4kg

Barrel

Overall length: 485mm

Weight: 2.95 kilo

Holdall

Overall size: 500mm x 300mm x 200mm

PIGSTICK EXPLOSIVE ORDNANCE DISPRUPTOR

NATO STOCK NO:1385-99-207-8890

The Pigstick Disrupter is a well-proven item of equipment originally developed for the

British Army as a means of disrupting thin-walled improvised explosive devices (IED’s).

It is extensively used worldwide by bomb disposal operators and is designed to provide

a high probability of avoiding the detonation or explosion of the suspect device. The

Pigstick Disrupter is a multi-shot device, capable of many firings without any distortion of

the main body and requiring minimum maintenance.




36 PIECE NON-MAGNETIC TOOL KIT

The36PieceNon-MagneticToolKit isdesignedforEOD operations. All toolsaremanufactured from

beryllium copper alloy and conform to Stanag 2897 standards. All tools are supplied in a heavy duty

fabric carrying case with non-magnetic fittings, with all tools having individual cutouts in foam trays

which provide an effective tool control system which clearly shows if any tool is missing. All tools

are suitable for contact use and are supplied individually certified

The 36 Piece Non-Magnetic Tool Kit comprises the following:

200mmTweezers Screwdriver 3 x 150mm Flat200mmProbe Screwdriver 4.5 x 150mm Flat255mm Scissors Screwdriver 6 x 100mm FlatHacksaw Screwdriver 8 x 150mm FlatHacksaw Blade Screwdriver 10 x 300mm FlatPutty Knife/Scraper 37mm x 191mm Screwdriver Offset 6 x 150mmWire Brush 4 Row Screwdriver Offset 6 x 130mmPliers Flat Nose 155mm Screwdriver Offset 10 x 140mmPliers Snipe Nose 170mm Screwdriver CrosspointNo.1Side Cutters 165mm ScrewdriverCrosspointNo.2BallpeinHammer ScrewdriverCrosspointNo.3Club Hammer with GRP Shaft ScrewdriverCrosspointNo.4Cold Chisel 16 x 165mm Adjustable Spanner 19 x 150mmCold Chisel 25 230mm Adjustable Spanner 28 x 255mmPry Bar 16 x 455mm Adjustable Spanner 28 x 355mmSwan Neck Bar 455mm Knife

Replacement toolscanbeprovided individually.

Approximate weight 13kgs.NATOSTOCK NO:

NSN 5180-99-589-3534




MSI FIRING CABLE REEL

The twisted pair black and brown Firing Cable was devised for use with an electronic

exploder, such as the Shrike, to activate a disruptor, de-armer or detonator.

MSI Firing Cable is designed for high strength, good electrical conductivity and concealment.is supplied in a reel, we can supply lengths from 100 to 1000 metres according to customerrequirements. MSI Firing Cable is manufactured in the UK to Defstan 6112 Pt.17 standards.

NATOSTOCK NO:

6150-99-665-8672




85 PIECE NON-MAGNETIC TOOL KITThe 85 Piece Non-Magnetic Tool Kit is designed for EOD operations. All tools are

manufactured from beryllium copper alloy and conform to Stanag 2897 standards. All tools

are supplied in a heavy duty fabric carrying case with non-magnetic fittings, with all tools

having individual cutouts in foam trays which provide an effective tool control system

which clearly shows if any tool is missing. All tools are suitable for contact use and are

supplied individually certified. Replacement tools can be provided individually.

36 Piece and 100 Piece Non-Magnetic Tool

Kits also available.

The 85 Piece Non-Magnetic Tool Kit comprises thefollowing:

190mm tweezers- straight & right-angled200mmprobeKnife225mm scissorsHacksawHacksawbladePutty knife/scraper 37mm x 191mmWire brush 4 rowScrewdriver 3 x 50mm flatScrewdriver 4.5 x 150mm flatScrewdriver 6 x 100mm flatScrewdriver 8 x 150mm flatScrewdriver 10 x 300mm flatScrewdriver offset 6 x 140mmScrewdriveroffset4x125mmScrewdriver offset 10 x 160mmScrewdrivercrosspointNo1ScrewdrivercrosspointNo2ScrewdrivercrosspointNo3ScrewdrivercrosspointNo4Pliers combination 203mmPliers flat nose 155mmPliers snipe nose 170mmSide cutters 165mmWire nippers 150mmPliers round nose 150mmPliers 200mmAdjustable spanner 19 x 150mmAdjustable spanner 28 x 255mmAdjustable pipe wrench 28 x 355mmBall pein hammer with GRP shaftClub hammer with GRP shaftCold chisel 16 x 165mmCold chisel 25 x 230mmPry bar 16 x 455mmSwan neck bar 455mmRatchet ½ sq.Sliding tee bar ½ sqExtension ½ sq x 100mmExtension ½ sq x 250mmUniversal joint ½ sqSocket ½ sq 10mmSocket ½ sq 11mmSocket ½ sq 7/16Socket ½ sq 1/2

Socket ½ sq 7/8Socket ½ sq 3/4Socket ½ sq 13/16Socket ½ sq 15/16Socket ½ sq 1Socket ½ sq 1.1/16Socket ½ sq 1.1/8Hex wrench 1,5mmHex wrench 2mmHex wrench 2.5mmHex wrench 3mmHex wrench 4mmHex wrench 5mmHex wrench 6mmHex wrench 8mmHex wrench 10mmHex wrench 1/16Hex wrench 5/64Hex wrench 3/32 Approximate weight 22kgs.Hex wrench 1/8Hex wrench 5/32Hex wrench 3/16Hex wrench 7/32Hex wrench 1/4Hex wrench 5/16Hex wrench 3/8Hex wrench 7/16

Socket ½ sq 12mmSocket ½ sq 13mmSocket ½ sq 14mmSocket ½ sq 15mmSocket ½ sq 17mmSocket ½ sq 19mmSocket ½ sq 22mmSocket ½ sq 24mmSocket ½ sq 27mmSocket ½ sq 30mmSocket ½ sq 9/16Socket ½ sq 5/8Socket ½ sq 11/16

NATOSTOCK NO:

NSN 5180-99-427-0622




The Bomb Search Kit is an inexpensive kit designed for IED search operation. It contains

a portable endoscope/boroscope, portable hand lamp, portable drill, as well as an

assortment of tools. When immediate visual inspection behind walls and panelling is

required, the portable drill set enables inspection holes to be drlled through all types of

material, allowing rapid internal inspection. The kit provides a range of tools for removing

panelling and inspection covers and is suitable for carrying out general searches in

vehicles and ships.

Large and small adjustable inspection mirrors are also included to facilitate searches in confinedspaces. The Bomb Search Kit is supplied in a fitted carrying case.

BOMB SEARCH KIT

NATOSTOCK NO:5180-99-322-3537

Leather glovesTrimming knife(retractable with spare blades)ScissorsMini saw ( + 10 blades)450g Claw HammerPhillips No 1 screwdriverPhillips No 2 screwdriverPhillips No 3 screwdriverPhillips No 4 screwdriverSlotted head 3mm screwdriverSlotted head 6mm screwdriverSlotted head 10mm screwdriverHexagonal wrench set imperialHexagonal wrench set metricWrench adjustable 6 x 150mmSelf-grip universal pliersCombination pliers 180mm

TweezersReleasing fluidHSS drill bits 5mmHSS drill bits 10mmHSS drill bits 12mmFlat drill bit 19mmFlat drill bit 13mmFlat drill bit 10mmDrill bit containerMasonary drill bit 10mm x 300mmTelescopic illuminated am140mm dia convex mirror65mm dia plano mirror65mm x 115mm rectangular mirrorEndoscope (powered by handlamp)HandlampCordless drill ½” chuck, 2 batteries 240v/110v, 14.4VDensimeter

Contents:




The Infrared Telescopic Camera System is a portable search kit ideal for use by police,

customs and special forces for searches of buildings, ships, aircraft and vehicles for

firearms, explosive devices, contraband and criminal suspects. The Infrared Telescopic

Camera System can also be used for short-term surveillance.

The Infrared Telescopic Camera System is highly versatile, comprising a high-resolutionmonochrome camera integrated with a powerful infrared illumination system mounted on atelescopic pole. The infrared illuminator enables the operator to 'see' in small, confined areas oftotal darkness. The displayed image is viewed on a compact monitor, which is fitted into a chestworn pouch to maximise mobility. Alternatively, a head-up display can be used, avoiding emissionof any stray light. Power is supplied by a rechargeable, battery pack within the chest pouch.

FEATURES

? Excellent range – up to 12 metres in total darkness? Battery Powered – up to 2 hours continuous use? High-resolution monochrome monitor? Automatic gain control – no adjustment necessary for differing light levels? Fixed focus with large depth of field – no need to refocus? Highly portable and robust? Simple to set-up and easy to use? Video output – allows use of ancillary equipment? Lightweight – comfortable to use and carry for extended periods? Robust carrying case – protects the equipment for both storage and transportation

INFRARED TELESCOPIC CAMERA SYSTEM

Standard set contains:Telescopic pole with camera head/illuminator,control unit 4” monochrome monitor, 1 x batterypack,batterycharger, chestpouch,carryingcase

and instructions:TECHNICAL SPECIFICATIONS

Viewing head:

Size: 215 x 38x 62mm includingilluminator

Camera: Monochrome 500H x 582 linesresolution

Sensitivity: 0.2 lux at fl.2Illumination: Infrared LED array – 950 nmPower: 12V DC 4 Ah, supplied bybattery in chest pouchTelescopic pole:

Type: Lightweight telescopicLength: 390 – 1470 mm extendedWeight 0.5kgMonitor:

Type: Monochrome – CRTSize: 135 x 235x 100mm with 4” screenResolution: 500 lines




DISRUPTOR POWER CARTRIDGES

MSI supplies a range of NATO-cased, electrically initiated power cartridges for use

with the Pigstick and other disruptors and de-armers.

Disruptor Cartridges are supplied and shipped in approved MOD ammunition containers.




The Shrike Exploder is a fully approved hard wire exploder which is currently in service

in more than 44 countries worldwide. From the arctic to the tropics it has proved itself as

asafe, reliableandcost-effectivesystemfor the initiationofexplosives,mines,pyrotechnics

and other electro-explosive devices (EED).

Spring-loaded terminals connect the four independent firing circuits. Circuit continuity is checkedby operating the appropriate TEST button. Operating the PRIME button causes the ‘READY’LEDto flash, indicating that the circuit is primed. This typically takes two seconds. While the ‘READY’LED is flashing, the load circuit may be fired by operating the appropriate Circuit Select and FIREbuttons simultaneously. The short recycle time of the Shrike permits rapid, individual firing on allfourcircuits,givingseven toeight times thepotentialdetonatingpowerofconventionaldynamotypeinitiators. Battery chargers are available for use with the Shrike.

The Shrike must be primed before any circuit can be fired, and firing requires the operation of twoindependent push buttons. The output is inhibited when the initiator is not fully primed, thuspreventingpartial firing. Theoutputenergycannotbe released inacircuitwhoseresistance ismorethan 40 Ohms, well below that of the human body, therefore completely eliminating any electricalhazard to the operator.

SPECIFICATIONS

Size: 140mm x 95mm x 45mmUnit Weight: 420gCase Material: Impact-Resistant PlasticFinish: Non-reflective drab oliveOutput Connections: Up to 4 separate circuitsControls: PushbuttonIndicators: LEDOperating Temperature range: -40ºC to 55ºCStorage Temperature range: -55ºC to 70ºCImmersion: 0-100% splash proofOutput Voltage: 319 – 400VOutput Energy: Typically 12J/ Minimum 6.8JOutput Load: Up to 400Ohms each circuitArming Time: 2 seconds

SHRIKE EXPLODER

NATOSTOCK NO:

1375-99-895-7682




FLEXIBLE COLOUR VIDEO ENDOSCOPE

The top-quality Flexible Colour Video Endoscope is supplied as a complete, fully portable

system specially designed for search professionals to use in areas that are difficult to

access, such as inside fuel tanks and behind concealed panels.

The Flexible Colour Video Endoscope has an 8mm x 3 metre, fuel/watertight, illuminated,crush-resistant Endoflex vertebrae core, tough polymer outer with Viton covered tip bendingsection. The endoscope has 4-way remote end tip with 120º up/down and left/right articulation.A full colour CCD camera chip is connected to the tip, and the image can be viewed on the colourmonitor supplied.

The Camera control unit comes in heavy-duty aluminium tilting case, including detachable lockingstorage compartment lid. the integral camera control unit has on-board auto-electronic shutter,144mm diagonal recessed LCD colour monitor and twin switchable 20w and 100w halogenlightsources.

Also available in 10mm and 12mm diameter shafts at the same price.

SPECIFICATIONS

Onboard power: 12vDC 13 amp hr rechargeable battery and charging unit.Front panel controls: Colour, contrast, brightness, lightsource select, illumination

intensity, 3-way standby, run and recharge select and Batterycondition indicator.

External power outputs: 90v -260v Ac 50/60Hz auto sensing, 12v DC




The DUS20 Digital Ultrasonic Distance Meter enables a search operator to identify

concealed false panels by electronically measuring the exact distance of cavities and

containers by emitting a laser beam to ascertain the true interior and exterior dimensions.

The battery-powered DUS20, an invaluable tool for professional search operators, is easy to use

and provides an instant display showing the exact distance between objects.

DIMENSIONS

Measuring Range: 0.6m to 20 metresOperating Temperature: -5ºC to +50ºCLaser Type: 650nm 1.5mWLaser Class: 2Battery: 1 x 9VWeight (with battery): Approx 230gmsSize: 157mm x 65mm x 36mm

DUS20 ULTRASONIC DISTANCE METER




PPE-100 MINE BOOT

? Strong durable construction? Available in full range of men’s and women’s sizes? NATO approved VIBRAM sole? Good ankle movement? Stable and comfortable? Enhanced limb survival and recovery? Further clinical data available on request.

? Incorporates the patented TABRE system for maximum blast protection andperformance

The PPE-100 Mine Boot is a comfortable, practical and rugged boot designed to offer an

advanced level of protection for personnel involved in mine clearance, reconnaissance

and de-mining operations. The PPE-100 Mine Boot has been designed with the wearer in

mind to maintain maximum mobility, durability and comfort in all climates.

The PPE-100 Mine Boot system comprises an outer boot, incorporating TABRE blast protection,a pair of inner boots and can also include an optional set of fragmentation protection gaiters. Thisprovides protection from the knee down and the provision of spare inner boots ensures that theoperator remains comfortable for each phase of the de-mining activity. Based on a well-provenalpine climbing boot, the PPE-100 Mine Boot is well suited to rough and uneven terrain. Theoptionalprotectivegaiterscanbesupplied invariouscolours,or camouflagepattern, tosuit specificrequirements.

The PPE-100 Mine Boot system has been tested at the Cranfield University Ordnance Testand Evaluation Centre COTEC, run under the auspices of the British Army’s Royal MilitaryCollege of Science at Shrivenham.




The Elex-7 Single Channel Electronic Exploder is a pocket-sized, single channel high-

energy electronic initiator designed for activating detonators and fuses. It is suitable

for military (EOD, IEDD, Engineers) and Commercial (demolition and excavation) use

anywhere where there is a need to use electric detonators, and has been proven to be

extremely reliable over the 15 years that it has been in military use.

The Elex 7 uses standard 9V alkaline batteries and is supplied in a robust and water-resistantprotective cover enabling it to be used in harsh environments.The unit is easy to operate and hasextensive safety features.

FEATURES

? High Energy Output:- capable of firing a standard commercial detonator over 2 km ofcable.

? Water-resistant.? Very compact and robust: high impact covering? Ergonomically designed: fits snugly into hand.? Uses standard 9V alkaline batteries.? Extensive tests and safety features.

SAFETY

Inadvertent firing is almost impossible because of recessed spring loaded-controls, and thedesign feature that requires two controls to be depressed simultaneously and in sequence forfiring. De-priming occurs automatically if the device is not fired. Despite the high energy outputthere is no danger to the operator touching the output terminals or conductors even in wetconditions.Any combination of detonator and cable can be used.The Elex-7 has an inhibit circuitto check that the total load is less than 400 ohms. This ensures against misfiring as well asagainst electric shock.

TECHNICAL SPECIFICATIONS

1. Output

Energy: > 6 JoulesVoltage: > 350 VoltsCapacitor: 100 microfaradContacts: Spring-loaded terminals for quick connections ofleads.

2. Power Supply

Two 9v alkaline batteriesCapacity: More than 250 firings from a set of new batteries at 25 ºC

3. Physical Characteristics

Width: 79mmLength: 155mmHeight: 32 mmWeight: 550g

4. Environmental

Operating Temp: -20° to +60°Storage Temp: -55°to +85°Drop: 2.5m

ELEX-7 SINGLE CHANNEL ELECTRONIC EXPLODER




The Customs Rummage Kit is a basic set of tools for Customs rummage and search

operations. The kit provides a range of tools for removing panelling and inspection

covers and is suitable for carrying out general searches in vehicles and ships.

Large and small adjustable inspection mirrors are also included to facilitate searches inconfined spaces.

The Customs Rummage Kit is supplied in a fitted carrying case containing:

63 piece socket set & bits –25 piece hexagon spanner set, metric & imperial24 piece combination spanner set, metric & imperialVehicle door trim/panel removing toolCombination pliers 7” insulatedTelescoping search mirror poleMirror to fit telescoping pole- 63.5mm diameterDental mirror – 22mm diameterAdjustable spanner – 300mmWrecking bar 340x45mmSafety torch – suitable for zone 0, 2xD cellScrewdriver - 400mm, 5.5 mm flat tipScrewdriver - 400mm, 8mm flat tip

CUSTOMS RUMMAGE KIT

NATOSTOCK NO:

NSN5180-99-986-6581




THE CMT is a truly compact vehicle search mirror and torch designed to fit into a pocket

or handbag.

Withaunique telescopichandle that is completely rigidwhenextended,aswell as an integral torchthat can be used when the mirror is opened or closed, the CMT Pocket Mirror is a valuable aidto personal security.

¨ Complete with batteries and spare bulb¨ Lightweight¨ Telescopic handle¨ Convex mirror¨ Integral torch

CMT POCKET VEHICLE SEARCH MIRROR




DE-MINING APRON & VISORThe De-Mining Apron was designed specially for UN de-mining operators. It is

provided with “add on” arm and shin protection, as well as a headmounted flip-up

ballistic visor providing protection against shrapnel and anti-personnel mines.

People entering minefields expose themselves to possible injury caused by stepping on ananti-personnel land mine. Injuries caused by an explosion are difficult to treat in the field andthe victim may die from blood loss before they can be stabilised or taken to hospital. The De-

Mining Apron and Visor has been specially designed to reduce and limit the injury causedby fragments (shrapnel) and blast from the detonation of an anti-personnel mine.

The De-Mining Apron & Visor is manufactured from KevIar, which is specially designedfor protection against fragments. The lightweight construction and the revolutionary designenhances wearability and comfort. The front area of the torso is protected, but leaves theback exposed, which enhances airflow and reduces heat build-up. Care is also taken to givesufficient protection to the de-miner in the kneeling position as well.

The De-MiningApron & Visor was developed in conjunction with input from United Nationsde-miners wearing the equipment under operational conditions.

SPECIFICATIONS

Apron: 3.9kg

Arms: 3.4kgShins: 1.7kgTotal: 9.0kgVisor: 2.4kgCover material: Colour or type optionalProtection:

Apron: STANAG 2920 V50 450 m/sVisor: STANAG 2920 V50 258m/s




This top-of-the-lineNon-ConductiveFlexibleEndoscopeisdesignedforsearchapplications,

such as the examination of fuel tanks, where it is essential that the shaft of the endoscope

is completely non-metallic and non-sparking.

FEATURES OF FLEXIBLE ENDOSCOPE

? 4-wayArticulation? Ruggedised? High resolution image guide? Ergonomic handgrip with diopter focus adjustment? 0° direct forward direction of view, 60° field of view? Integral 1.5 metre long light guide cable, with BS/ACMI male light-source connector.? BS.31.75mm solid tapered eyecup, photo adaptable? 4-way +/- 120° remote tip articulation

FEATURES OF PORTABLE LIGHTSOURCE

? 100w quartz halogen 12vDC. Waist-belt mounted lightsource? Screw interchangeable BS/ACMI female lightguide boss? Shutter light control, push button LED battery condition indicator? Lightsource supplied complete with one fitted 10 Ah rechargeable battery pack and

charger, battery pouch with integral adjustable waist-belt

SPECIFICATIONS

Diameter: 6mm

Working Length: 1500mm (other lengths available)

NON-CONDUCTIVE FLEXIBLE ENDOSCOPE KIT

NATOSTOCK NO:

NSN 6650-99-353-0763




The EVD-3000 is arguably the most advanced explosives detector available today. The

system has been in use in dozens of countries worldwide for many years and is well-

proven equipment. It is ready to operate in only 60 seconds and provides a response in

15 seconds. The EVD-3000 is capable of detecting the presence of plastics and high

vapour-pressure explosives, making it one of the most sensitive detectors available

worldwide. The EVD-3000 detects traces of both particulates and vapours, allowing for

non-invasive searches of luggage, personnel, mail and containers.

N.B The new E3500 Portable Explosive Detector will also detect home-made liquid and

volatile peroxides, including TATP and DADK, chlorates, ANFO and pipe bombs, which

are popular in suicide and truck bombings.

OPERATING THE EVD-3000

The EVD-3000 is a flexible and easy to operate explosives detector, offering both vapour andparticulate sampling without the use of a radioactive source or external carrier gas. Vapours aresampled directly via the sampling nozzle. Particulates are sampled by swiping a suspected objectwith cotton gloves or wipes and then transferring the traces to a screen, which is inserted into thesampling port. The EVD-3000 starts processing samples immediately and gives results in justseconds.

DATADISPLAY

All results are indicated on the LCD and by a volume-adjustable audio alarm, making detectiona simple one-step process.

SPECIFICATIONS

Detection Principle: Electrochemical (Thermo-Redox) detection.No radioactive source.

Detectable Compounds: Most military and commercially available explosives suchas C4, TNT, Dynamite, PETN, Semtex, EGDN, DMNB andNitro-glycerine, including ICAO Taggants (DMNB, EGDN,o-Mint, p-Mint).

Sampling Capabilities: Vapours and particulates.Typical Analysis Time: 10 seconds.Warm-Up Time: One minute, with regular use.Carrier Gas: None required.Power Supply: 12 volt DC rechargeable battery pack.

External battery pack.12 volt AC adapter.

Operating Temperature: -5°C to +55°C.Weight and Dimensions: 3 kg.

(LxWxH) 51 x 14 x 11 cm.Shipping Weight: 12kg.Shipping Dimensions: (LxWxH) 57 x 26 x 39 cm.

EVD-3000 PORTABLE EXPLOSIVE DETECTOR




HEAVY DUTY EOD TRIPOD

The EOD Heavy Lift Tripod has been designed to enable a bomb disposal operator to remotelylift a suspect improvised explosive device (IED) weighing up to 750 kg, from recesses such astrailers, culverts and drainage holes. The EOD Heavy Lift Tripod offers a far greater lift capabilitythan the standard EOD Tripod and therefore is a “must have” for any serious EOD Team.

The telescopic legsof theEODHeavyLift Tripod canbeadjusted to theappropriateheight, allowingfor flat or sloping ground, and then locked into position. The foot of each leg can be secured tothe ground by spikes or self-levelling pads.

The top of the tripod is fitted with a triple block, or pulley, with bearings for easy lifting of heavyobjects, through which a rope with a karabiner at one end is fitted. Lifting tackle is attached tothe karabiner and the operator can lift the suspect article. There are four different lifting options,ranging from a ratio of 6:1 to 12:1. The rope runs from the karabiner up to, and through, thetriple block or pulley at the top of the tripod and then down then down to the base of one of thelegs where another triple block with a jammer is fitted. This ensures that when lifting the suspectobject, the lift is provided via thebase of theEODHeavyLift Tripod ensuring that the tripod cannottopple over.

Specifications:

Materials: Non-Magnetic.Lift Capability: 750kg.Total Storage Weight: 30kg.LiftingHeight: 2.2m(5heightsavailable).Overall Height: 2.6mStorage Length 1.5m (In two bags)

MSI Security Products Ltd also supply a heavy liftEOD Tripod capable of lifting articles weighing up to750 kgs. This unit lifts articles up to 2.5 metres and isslightly larger in size and is 30kgs in weight.

NATOSTOCK NO:

1385-99-341-5051




MIT HANDS-FREE METAL DETECTOR

The MIT Hands-free Metal Detector is designed to allow the operator to search for metallic

and non-metallic objects simultaneously. Its silent vibrating alarm offers covert detection

and is able to discriminate between large and small metal objects.

The MIT Hands-Free Metal Detector comes in one universal size, which fits both the left andthe right hand. It is simple to use and requires no additional training.

FEATURES

? Standard 9V Battery.? 100% Finger Dexterity? Fully Automatic? Ideal for Body Searches? Silent VibratingAlarm? Medical Implant Friendly.? Non-Interference to magnetic recorded material.


Construction: Neoprene / Velcro

Weight: 0.4 lbs (incl battery)Sensitivity: Target Size 0.5gramsOperating Time: 150 hrs continuous at +25C (alkaline battery)

80 hrs continuous at +25C (rechargeable battery single charge)Battery: Standard 9 Volt block battery or equivalent alkaline disposable or

rechargeable.Alarm: Signified by vibrating tactile indicator.

After detection automatic reset.Short Pulse Small targetLong Pulse Large target.




DCU500 DETONATOR CONTAINER

The DCU500 Detonator Container is designed to provide the safe transportation andstorage of up to 8 electric, non-electric and forensically recovered improviseddetonators.

? UN Hazard Classification 1.4s? Safe isolation, movement and containment of detonators? Standard NATO approved container with TABRE inner lining? Full containment of fragments, overpressure and product gases? 7 minute fuel-fire rating? Larger sized containers available

Dimensions

Size: 145mm x 185mm x 280mmWeight: 8kgColour: Red




SPECIAL SEARCH CAMERA KIT


Image device: 1.4 inch ITCCD 752 x 582 pixelsHorizontal resolution: 470 TV linesAuto focus: YesS/N: Less than 50dbMin focus distance: 0mm (wide angle setting)Optical zoom: x10:4.2mm - 42mm (f1.8 - f2.9)Temprature: 0 - 50ºC

The Special Search Camera Kit, or Telescopic Colour Zoom Camera System as it is also

called, is a portable, lightweight system designed to provide crisp, high quality full colour

images for EOD/IEDD search, as well as SWAT and fugitive surveillance operations. It is

ideal for searching shipping containers, ships' holds, cabins, vehicles and any dark,

inaccessible locations.

The Special Search Camera Kit consists of a 5 section telescopic pole, which extends from390mmto 1470mm, with a flexible joint fittedwith a watertight colour camerahead 60mm diameterx 107mm long which is attached to a 2.5 metre camera cable. Ultra bright light illumination isprovided by an LED ring light array in two mixed, switchable banks.

A separate control unit with adjustable neck strap allows hands-free operation and comfortableviewing of the 6.8” colour TFT monitor. The control unit contains controls for camera zoom, poweron/off and light switching, as well as the monitor’s press buttons for controlling mirror image, rotate,brightness and colour contrast. In addition the control unit contains an integral 12v DC battery,external 12v DC input and 240v AC input for the battery charger




HARD WIRED COMMUNICATION SYSTEM

The Hard-Wired Communications System is designed specifically for EOD teamsusing the Mk5 EOD Bomb Disposal Suit.

The system provides communication between the bomb disposal operator and his back-up team.It consists of a plug which connects to the helmet’s in-built earpiece and microphone, 100 metresof twisted core signal cable mounted on a spool, a headset, speaker/amplifier, and carrying bag.




IED DEMOLITION KITThe new (Year 2003) IED Demolition Kit was developed in collaboration with British Army

bomb disposal experts as a man-portable kit, which can be easily carried in a rough

terrain.

The IED Demolition Kit is designed for infantry, engineer and EOD use for the safe carryingof all equipment necessary for activating a detonator, fuse or a disruptor/de-armer to destroy asuspect bomb mines and other unexploded ordnance. The kit, contained in a specially modifiedbergen back-pack, is not provided with live detonators, but comes with a NATO-approvedcontainer which has been specially developed for the safe transportation of live detonators.

Equipment supplied includes:

Elex-7 Electronic ExploderDetonator ContainerPliers2 x Hand-Held RadiosCrimper with CutterWire CuttersElectrical TapeDuct TapeStanley KnifeWooden Cutting BoardMeasuring TapeSmall Hacksaw (with spare blades)Screw DriversHammerCable TiesMini-MagliteTorchBergen/Rucksack250 metres of Firing Cable

NATOSTOCK NO:

1385-99-378-4419




CONTENTS:

1x SAFE-C SECURITY MIRROR

1x REEL, WHITE KEVLAR FITTED WITH SNAP HOOK

1x REEL, BLACK KEVLAR FITTED WITH SNAP HOOK2 x SNATCH BLOCK1x HOOK, SMALLSINGLE PLAIN1x HOOK, MEDIUM SINGLE PLAIN2 x HOOK, MEDIUM DOUBLE PLAIN1 x HOOK LARGE SINGLE PLAIN2 x 25MM EYE1 x ROPE SLING, 3MM DIA X 2M LONG, SOFT EYE1 x ROPE SLING, 4MM DIA X 2M LONG, SOFT EYE1 x ROPE SLING, 5MM DIA X 2M LONG, SOFT EYE1 x WIRE SLING, 1.5MM DIAX 2M LONG, 30MM1 x WIRE SLING, 2.0MM DIAX 2M LONG, 30MM1 x WIRE SLING, 3.0MM DIAX 2M LONG, 30MM2 x TRIPLE BARB HOOK WITH MOUNT FOR TELESCOPIC POLE1 x PITON SPEARPOINT 55MM LONG1 x PITON SPEARPOINT 80MM LONG1 x PITON CHISEL 55MM LONG1 x PITON CHISEL 85MM LONG1 x DOUBLE SUCTION PAD WITH ANCHOR POINT2 x CANTILEVER CLAMP2 x LIGHT WEIGHT SPRING GRIP1 x SELF LOCKING FORCEPS1 x 10 SELF GRIP PLIERS WITH EYE10 x SCREW EYE SELF TAP1 xADJUSTABLE CLAMP SYSTEM2 x KARABINER (ALLOY) 18MM SCREWGATE 27kN2 x KARABINER (ALLOY) 25MM SCREWGATE 27kN1 x SHACKLE D SHAPE 13MM GATE4 x AUTOMATIC OPENING SNATCH BLOCK

1 x ROPE EYE1 x TELESCOPIC POLE FOR 3 HOOKS1 x HOOK SPRING GATE 15MM1 x HOOK SPRING GATE 50MM1 x BELT SLING1 x PULLEY WITH JAMMER CLEAT2 x TORPEDO RELEASE10 x STICKY EYE2 x GANGWAY BRACE1 x IEDD SKID PAN (SLEDGE)4 x DOOR STOP PLASTIC WEDGE2 x WEDGE IT BLACK

COMPREHENSIVE HOOK & LINE KITThe Comprehensive Hook & Line Kit provides a bomb technician with a wide range of

equipment that can be deployed to gain access and remove, manipulate and handle

suspect explosive devices contained inside buildings, vehicles, as well as in open areas.

Included in the Comprehensive Hook & Line Kit is a wide range of tools and equipment designedspecially for a bomb disposal professional to successfully dispose of hazardous devices. Theportable Comprehensive Hook & Line Kit is supplied in case with a foam insert and containscomponents for attaching line, anchoring pulleys and manoeuvring dangerous objects to a safeposition

The components of the Comprehensive Hook & Line Kit were developed in conjunction withBritishArmy bomb disposal experts, as Hook and Line rigging equipment is recognised worldwideas an integral component of any EOD team’s inventory.

Size: 112 x 40 x 54cmWeight: 35kg




The portable Endoscope Search Kit has been designed as a competitvely priced search

kit for use in buildings, cars and vessels.

The Endoscope Search Kit is provided in a foam-lined carrying case and consists of the followingcomponents:

? 12mm diameter rigid, lamp-lit, endoscope

? Battery charger

? Rechargeable power pack with belt

? Telescopic arm for use with mirrors (extendable to 1.5m, 480mm when closed)

? Rigid arm for use with mirror (overall length of 0.5m)

? 2 x SM-140-C 140mm diameter mirror

? 1 x SM-R-P 115mm x 65mm mirror

? Spare lamp

? Foam lined fitted case

ENDOSCOPE SEARCH KIT




General Specifications:

Insertion Tube Diameter: 4.0mmInsertion Tube LengthsAvailable: 600mm (others available on application)Insertion Tube Bend Radius: 250mm minimumInsertion Tube Field of View: 70º (others available on application)InterchangeableTips available: 0º forward, 30º and 70º obliqueEyepiece Configuration: 31.75 standard European eyecupEyepiece focus: Diopter TypePixels: 30,000

Optional:

Higher resolution Viziscope with 50,000 pixels also available

NATO STOCKNO:

5855-99-549-5543

VIZISCOPE FIBRESCOPE WITH INFRA

RED LIGHTING SYSTEM

The Viziscope is a widely used fibrescope with a 600mm working length and a finely

tapered, 1.6mm diameter pin-hole tip. This tip provides an outstandingly bright image with

a seemingly endless depth of image sharpness. The equipment is supplied as a complete

kit, complete with a high-resolution monochrome CCD camera, hands-free monitor, as

well as an infra-red illumination board and carrying case.

The Viziscope Fibrescope uses an infra-red light source and the portable mini-monitor, which issupplied with a waist and neck strap for hands-free use, the Viziscope Fibrescope can ‘see’ upto 4 metres in areas of complete darkness. This makes the equipment ideal for covert surveillanceand search tasks, such as looking under a door to examine the contents of a room or container,looking inside cavities and voids etc. Viewing is 0º directly forward, with a wide angle 70º field ofview.

The infra-red illumination board, which is powered by a belt-mounted rechargeable battery,provides ‘black light’ which is invisible to the naked eye and thus cannot be seen by the occupantsin a room. However, with the use of the high-resolution CCD camera an image can clearly be seenon the mini-monitor.

Optional 30º and 90º field of view are available.




ProbeDiameter: 20cm (8")Height: 36” Handle to floor (short mode)

56” fully extendedWeight: 1.5kg (3.2lbs)Power: Standard 9 volt alkaline batteryConstruction: CombinationofcompoundPolycarbonate,

aluminium and ABS. Ultra strong & ruggedconstruction throughout the unit.

Sensitivity: Fully adjustable sensitivityTarget size better than 0.5 grams

OperatingTemp: -20ºC - +65ºCStorage Stemp: -30ºC - +80ºCHumidity: 98%IngressProtection: IP64(IEC529)PowerSource: 1 x standard 9 volt alkaline batteryPowerConsumption:StandbyCurrent: NilActiveModeCurrent: Less than 1mA(nodetection)Alarm Mode: 6.5mA(metaldetected)AlarmIndication: Alarm indicated in two modes with a 2-way rocker switch

(a) Audio Visual (beeper and red LED)(b) Vibration only – tactile vibration from the handle of the detector to the hand of

the detector.Detector beeps only when metal is present

DetectionSpeed: Ultra fast Detect – Alarm and reset – ready for another target in 0.1seconds

BatteryManagement: Precision battery monitoring. Low power is signaled by yellow LED indicator onmain control panel. Totally exhausted battery is indicated by continuous red andyellow in alarm mode, after detecting metal.

Battery Life: 9 volt battery up to 240 -mA hrs or longer with normal use. (disposable alkaline)(less in vibration mode)

Controls: On/Off rocker switch (greenflashing LED indicates ON). Red LED indicates alarmmode. Yellow LED battery power is low. 2-way switching between A/V & VIBmode. Minature sensitivity adjustment knob.

TargetTypes: Instant response to all metals

????? Inexpensive

????? Audio and silent vibration alarm

????? High sensitivity to ultra small targets

????? Ultra lightweight

????? Powered by a single 9volt battery

????? Advancedpoly-carbonateconstruction

The new (Year 2003) AX777 High Sensitivity Ground Search Detector is manufactured by long-

standing experts in the field of metal detection and is a ruggedly constructed, competitively priced

metal detector designed for ground search operations.

Although originally designed for Police search operations, the AX777 has surprised British and U.S. militaryexperts at its ability to detect buried items with minimal metal content and its ease of use.

TheAX777 is testedandapproved toEECEN5008-1 table1,EN50082-1 table1:1.1 radiatedemissions (CEmarked) and conforms to international standards IEC, NILEC, FCC, FAA. The detector has been medicallytested and presents no risk to persons with pacemakers and no interference with magnetic recordedmaterials.

TECHNICALSPECIFICATION

AX777 HIGH SENSITIVITY GROUND SEARCH METAL

DETECTOR




VIZISCOPE FIBRESCOPE KIT

The Viziscope is a very competitively priced flexible endoscope designed for covert

search and surveillance applications where only a tiny viewing aperture, such as a key

hole, under a door, or even a pin hole, may be available. Having an image bundle with

30,000 pixels, each of only 8 micron diameter, the Viziscope gives outstanding image

resolution and exceptional light response, making it suitable for use in low light conditions.

An operator simply inserts the 4mm diameter tip of the 720mm long flexible endoscope througha suitable aperture. The eyepiece has a diopter focus adjustment or, for long-term applications,one can simply attach it to a CCTV camera via the "C" mount adaptor provided. The fully flexibleViziscope has a tough polyurethane protective oversheathing.

General Specifications:

Insertion Tube Diameter: 4.0mmInsertion Tube LengthsAvailable: 600 and 900 mm (others on application)Insertion Tube Bend Radius: 250mm minimumInsertion Tube Field of View: 70 (others on application)InterchangeableTips available: 0 forward, 30 and 70 obliqueEyepiece Configuration: 31.75 standard European eyecupEyepiece focus: Diopter Type

Options:

? Special silent running light source with fibre lighting oversheath. White or IR lighting? Low cost Viziscope - 12,000 pixels? Higher resolution Viziscope - 50,000 pixels, 300mm length

Accessories:

? C/CS camera adaptor with adjustable focus? Monochrome 0.02 Lux camera? Monochrome 0.5 Lux camera? 9" Format 750 line resolution monochrome monitor




VISOR UNDER VEHICLE SURVEILLANCE SYSTEM

(VUVSS)VISOR is a new, competively priced security system designed for the detailed inspection of the

undersidesof roadvehicles. Thesystemproduces,withina fewsecondsof thevehiclepassingover,

a single colour image of the entire underside from a portable and lightweight unit capable of being

deployed within minutes.

VISORusesadvanced imaging technology toconstructasingle image fromvideosequences fromeachof thesystem’s fivecameras.Theuser interfaceallows theoperator to ‘browse’this imageandviewtheoriginalvideoframes at full resolution. This feature enables the user to inspect areas of interest from differing viewpoints.

VISOR has been designed to be portable and self-contained. The complete system comprises two units - animaging unit and a viewing/control unit. Both units can be easily carried in the trunk of a car. The imaging unitcan he positioned temporarily or it can be permanently installed in any place where there is vehicular traffic.Installation simply requires the user to deploy the imaging unit, connect the cables to the viewing unit,and apply power and start to use. The system can operate from a 12v car battery and as such may be usedin locations without access to mains power.

The VISOR system is suppplied as a complete system including a high specification, small-format computerwith large storage capacity, cables and carry cases.

? Single image of entire vehicle underside in seconds? Compact, lightweightand portable? Easily deployed by one operator? Completely self contained and ready to use within minutes? Simplicity of operation? Detailed inspection of original video frames? Integrated lighting allows usage under any conditions - day or night? 110v/220v,50/60MHzmainsoperation? Low power consumption - can operate from portable power sources? Up to 20m distance between imaging and viewing units? Weatherproof (IP65Rating)? Storage and/or transmission of data for future analysis? Extendibilityofperformance throughsoftwareenhancements

FEATURES

? The imaging unit provides complete coverage of vehicle underside allowing viewing into the wheelarches

? Simple user interface allows easy viewing of underside details at full video resolution.? Results may be saved for later inspection and comparison.? Future upgrade will offer automatic number plate recognition capability.

Video frame from single camera




KD60 EXPLOSIVES TEST KIT

????? Accurate

????? Discreet

????? Reliable

????? Cost-effective

????? Easy-to-use

????? Negligible false alarm rate

The KD60 Explosives Test Kit is in service with the UK government and is an extremely

simple-to-use system, with a negligible false alarm rate, designed to detect all types of

military explosives. Because of its relatively low price it can be issued to security forces

in far greater numbers than conventional explosive detectors, which tend to be expensive

and usually require the operator to have had some technical training.

The KD60 Explosives Test Kit will test for Semtex, C4, TNT, RDX and PETN in less than threeminutes, providing a fast and extremely accurate result. A Separate KD40 Test Kit is alsoavailable to detect home-made explosives. The test is specific for each of the components listedabove and gives a specific positive indicator. Built to military standards, the easy-to-followinstructions on the inside lid minimises training requirements.

English instructions supplied as standard, however other languages can be supplied as required.

Test per Kit

4 x sachets each containing tests for RDX,PETN and TNT4 x swabbing tool.

Dimensions

Size 167x72x28mm (LxWxH)Including hanging tab




TABREshield 1000 Explosive Isolation Unit

The TABREshield 1000 Explosive Isolation Unit has been designed for the safe

containment of postal bombs, explosives and IED devices and has been developed in

consultation with UK Government EOD and IEDD experts.

The units are designed to accommodate a wide variety of packages and parcels, includingcalendarsanddrawing tubes.TheTABREshield IsolationUnits aresimple-to-use, intrinsicallyvented steel boxes lined with the unique TABRE® blast attenuation materials. Each unit hasa fail-safe, three-catch, positive closing system allowing one to immediately identify whetherthe TABREshield is closed correctly. The units are small enough to fit under most worksurfaces, thus allowing them to be discretely hidden away.

The TABREshield 1000 has a number of applications due to its excellent manoeuvrability andversatility. These include the safe storage of confiscated fireworks and pyrotechnics atsporting events and the more standard EOD/mailroom applications. One additional benefit ofthe TABREshield is that all blast fragments are contained within the system, thus allowing forthe fast and effective collection of forensic evidence.

The TABREshield works as if resembling a 'sponge' - the labyrinth of tiny air pockets in theTABREshield 'sponge' traps energy from the explosion and breaks-up and absorbs theshockwaves from the blast, capturing it in the air pockets and forcing it through a convolutedpath to escape. The two other layers in the system catch any fragments and resist thepressure of the expanding hot gases.

SPECIFICATIONS

External dimensions: 630 x 650 x 680mmInternal dimensions: 475 x 380 x 350mmLongest internal diagonal axis: 700mmInternal capacity: 63.175 litresWeight: 100kg




Knight ROV

particularly well-suited as a:

????? Hazardous duty robot (hazmat robot)

????? EOD robot (explosive ordnance disposal robot)

????? Bomb disposal robot (bomb robot)

????? IEDD robot (improvised explosive device disposal robot)

????? Surveillance robot

????? SWAT robot (special weapons and tactics robot)

The Knight ROV is a new generation of ruggedised, medium-sized, hazardous duty robot, whichprovides excellent precision and dexterity. Police, Military, Emergency Response Team, Fire, Nuclear, andotherHazardousResponsepersonnelcanutilise themulti-purpose KnightROV. It canalsobeusedfor surveillance, reconnaissance, handling of hazardous items, manipulation of suspected packages,neutralizing and handling such items as Improvised Explosive Devices (IEDs), Hazardous Chemicals, andRadioactiveMaterials.

The Knight ROV is an all-weather, all-terrain mobile robot for indoor (buildings, public institutions,airports,homes,etc.)andoutdoorenvironments (terrainclutteredwithobstacles,ditches,gravel, snow,mud,etc.). It is remotely controlled, and consists of a robust platform, a dexterous robot arm, operator controlstation, communication links, and a variety of operational tools and accessories.

Special features of the Knight ROV are: quickly-removable tracks, quickly-removable articulatedwheels in front and back for better stability on stairs and slopes, precise independent joint control, longreach, high payload, and expandable to autonomous navigation.

KnightROV–SPECIFICATIONS

? Suitable foroperating indoor (buildings,homes,airports, trainstations)andoutdoor (urbansettings,rough terrain, inobstacle-clutteredenvironments,ditches,stairs,mud,gravel,etc).Thewheel/tracksystemisveryreliable.The tracksaremountedaroundthewheelssothat thecontactbetweenwheelsand trackspreventsdamageor run-awayof trackswhenpiecesof stoneorgravelenterbetween thewheel and the track. The tracks are extremely durable due to a heavy-duty design and strength.Anoperatorcandismount the tracks in fewminutes,anduseonlywheelswhen there isnoneed toclimbover obstacles or up/down the stairs.Apair of articulated wheels prevents rollover while climbing ordescending stairs, and help mounting high or wide obstacles.

? Can be used with weapons and tools for neutralisation of improvised explosive devices, handling ofexplosive materials, suspicious parcels, and inspection of trapped vehicles.

? Robot arm is unique in the sense that it provides servo-precision motion allowing the operator toapproachtohandleorhita targetwithsub-millimeteraccuracy.Theoperatorcancontrol several jointsat once allowing the end-effector (gripper, weapon, tool) to move in any desired direction.

? Manipulator can have 7 joints: turret, shoulder, elbow, wrist base, linear extension, and wrist roll.Various accessories can be attached to the arm. The tools and modules are quick-to-connect/disconnect units.

Knight ROV consists of: Platform, Manipulator Arm, Wrist, Gripper, Cameras, Control Station, Communication(cable and/or wireless) with Video and Audio links, and Accessories (Disrupter, X-Ray, Shotgun andWindow Breaker, etc.)




DIMENSIONS: Width 27.5 in (70 cm); Length 50 in (127 cm); Height 31 in (79 cm)WEIGHT: Standard configuration 550 lb (250 kg); with accessories 660 lb (300 kg).CLIMBING ABILITY: 45° stairs or slopes with tracks; Tracks can be installed and removed within afew minutes by one person; Obstacle height: 11.8 in (300 mm); Obstacle width: 11.82 in (300mm)MANEUVERABILITY: 360° turns in a 55 in. (1.4 m) circle; allows turning while driving; Precise speed-control for each joint; incremental motion of each joint allows 1 – 5 mmSPEED: 0 – 22 in/s (0 to .56 m/s); 0 – 2.0 Km/h.; Higher speed possible with geared transmission.OPERATING RANGE: Wireless RF 1640 ft (500 m) open-area; 200 m urban area; Onboard fiber-opticor coaxial cable 656 ft (200m).DURATION OF MISSION: 3 - 5 hrs.TOOL KIT and BATTERY CHARGER: Various tools for Knight ROV maintenance; Battery charger is asmart-charger, which recharges battery pack in 3 hours.OPERATING&USERMANUAL: Supplied.REACH:

Vertical: 98 in (2.5 m) from ground (Standard configuration)Horizontal:69 in (1.75 m) from front edge of platform (Standard configuration)

LIFT CAPACITY: 55 lb cc (25 Kg) With arm fully extended 264 lb (120 Kg) Above edge of platformWEAPONS/TOOLS:

Disrupter mount and disrupterShotgun mount assembly and shotgunX-ray mount assembly and X-ray unitWindow breaker assemblyCharge drop reel assemblyOther accessories made to orderFiring circuits (0/24VDC with safety switch andtimer delay): 2 on Arm, 2 on VehicleRelay circuits (open/close, 24VDC): 2 on Arm, 2on VehicleCOMMUNICATION: Wireless link (2-way Data andAudio, 1-way Video);Also Onboard Fiber-optic orCoaxial CableAutomatic Winding.ENVIRONMENTAL: Operates in all types ofweather conditions, day and night, and varioustypes of wet and dry surfaces; Operational temperature range from –20 to +45°C; Environmentalhumidity up to 95% at 25°C; Storage temperature range from 0 to 45°C; Weatherproof.MODULES: Vehicle, Turret, Arm (Shoulder, Elbow), Wrist (Base, Pitch, Roll), Linear Extension,Gripper, Cameras, Cable & Wireless RF Communication, Control Station, Accessories such asDisrupter and various other attachments.ARM CONFIGURATION: Manipulator is a 2 to 7-axis robot with the following joints:Turret Rotate the arm about vertical axisShoulder Rotate the arm about horizontal axisElbow Additional rotation about the horizontal axisWrist base first wrist rotationWrist tilt (pitch) Second wrist rotation axis

STANDARDCONFIGURATION

OPERATOR CONTROLSTATION: Portable; Enclosed in a weatherproof enclosure; Control panel withjoysticks and switches to control all robot functions; Colour LCD monitor (diagonal 15” 38 cm); VCRconnectors (for an external VCR or TV monitor); Operates at 12 VDC or 110/220 VAC; 2-way audiocommunication (microphone and 8-W speakers on the vehicle and at operator control station orheadset.VIDEO DISPLAY: Camera images (4) picture-in picture; battery status; diagnostic messages.PLATFORM: Six-wheel drive for all terrain with two 24 V or 48 V drive motors controlled by high-qualityservo drivers. Optional: articulated wheels (up 90° down 45°) mounted on the back and front panels foradded stability on ascent or descent of stairs and maneuverability over obstacles; Lights: Halogen -two 20 W lights on front of platform, one 20 W on the surveillance camera. Speaker and microphone;battery pack: 24 V or 48 V removable with four gel-cell batteries; 64 Ah; battery duration 3-5 hrs; on-board charging; Battery charger supplied.




TRACKS: For stair climbing, steep slopes, and rough terrain; mounted over the rubberwheels; can be removed and installed in 4 minutes.ON-BOARD ELECTRONICS:The on-board electronics and computer is based on the latestgeneration of Intel Pentium processors and stack of PC/104 boards for controlling theplatform, arm, and communication. The electronics is very rugged and capable ofwithstandingall-terrainoperation inout-doorenvironments.ARM: Shoulder or back-arm allows rotation of the arm in vertical plane (215°); Elbow orforearm (260°); Forearm is used to attach interchangeable modules (Wrist & Gripper,Cameras, and Accessories etc).WRIST ROLL: Roll joint (+/- 100°).GRIPPER: Standard gripper up to 12 in (0.3 m) fully open; poportional gripping force; max.gripping force 36 Kgf (80 lbf).ARM(RELOCATABLE)CAMERA: Color;wide-angle lens;auto iris.SURVEILLANCECAMERA& EXTENSION: Color CCD; remote zoom (72:1); remote focus;auto iris; pan +/- 170°; tilt +/- 170°. Optional: extension parallelogram arm: 60 cm.DRIVE CAMERA: Color; wide-angle lens; auto iris.CABLE REEL: 656 ft (200 m) of standard cable on a reel assembly; free wheel unwind andmanual rewind.

OPTIONS

ARTICULATED WHEELS: Two 2-wheel frames connected to back and front panels of the platform;rotates Up: to 90° and Down: to 45°.TURRET: Rotation (-120° to180°).WRIST BASE ROTATE: Roll joint (+/- 100°).WRIST PITCH (TILT): Tilt joint (+/- 100°).LINEAR EXTENSION: Linear joint extending 150 mm.HEAVY-DUTYGRIPPER: Forextremeruggedness.GRIPPER CAMERA: Color; wide angle; auto iris.EXTENSIONARM: For surveillance camera 600 mm.INFRAREDCAMERA:Enhanced low-lightvision;smallweatherproof IR-sensitivecamerawithLEDillumination; For 10 ft in total darkness; external illumination unit can be added for longer distance.ON-BOARDCABLEWINDINGSYSTEM:Mountedon vehicle; free wheel unwind and automatic rewind;fibre-optics or coaxial cable: length 656 ft (200 m).WIRELESS RF COMMUNICATION LINK: 1640 ft (500 m) open area; 200 m urban; 2-way data andaudio;1-wayvideo.

ACCESSORIES

DISRUPTER MOUNT: Dual mount with quick-connect mechanism; manually adjustable tilt angle.DISRUPTER AIMING & FIRING SYSTEM: Precision pan and tilt unit; direct laser aiming; resolution:+/- 0.02 in at 10 ft (+/- 0.5 mm at 3 m).DISRUPTERS:Userselection.SHOTGUNMOUNT

LASERASSEMBLY: High power laser-pointer assembly (visible in bright sunshine); for recoilessdisrupter or shotgun mounts.SHOTGUN: 12 gauge Franchi or user selection.LASER RANGE FINDER: Distance measurement to 100 ft (30m); accuracy 1/8 in (3 mm).X-RAY MOUNT: X-ray system mount with quick connect mechanism.X-RAYEQUIPMENT:GoldenXR200oruserselection.WINDOW BREAKER ASSEMBLY: Held by gripper; used to break windows in cars, walls, and doors.CHARGE DROP REELASSEMBLY: Low friction reel that can lay down 50 ft (15 m) of wire.




? Enhanced target definition

? Unsurpassed detection range

? Piezoelectric speaker

? Clear, sharp, detection signal pinpoints the target

? Five individual sensitivity settings

? No response to aluminum, brass or copper

? Ease of operation reduces search time

? 40-hours operation on two economical 9-volt batteries

? Modular construction

? Weather protected controls

? 5 year warranty

In use with the British, US and many NATO countries, the GA-72CD Magnetic Locator is

designed to withstand the rigours of daily on-site usage in a wide range of environmental

conditions. It is so rugged and dependable that it is backed by a 5 year warranty.

Designed for one-handed operation, the on/off, sensitivity and volume controls are on theunderside of the cover to provide easy access and protect the control knobs from damage. TheGA-72CD Magnetic Locator has an easy-to-read digital and bar graph which displays the signalstrength and polarity. Once the target has been located using the audio signal, the digital readoutand polarity will help to visually pinpoint the target.

FEATURES

GA-72CD MAGENTIC LOCATOR

Size: 8 x 8 x 100cmWeight: 3.2 kg




The Vulcan consists of an easy-to-use kit from which a small point-focal and explosively-

formedprojectileshaped-chargecanbeassembled.TheVulcan'splasticbody is internally

shaped to contain a plastic explosive charge and is provided with a detonator well.

Various types of projectile are available and these are selected according to the intended

application.

User-filled charges can be transported and stored as a set of inert components, then assembledby the operator to meet specific applications and then filled with plastic explosive. Explosive loadsvary between five and fifty grams according to application.

The lightweight plastic body construction of the Vulcan ensures ease of portability, so an EODoperator can carry a large number of charges which require no heavy means of support. TheVulcan charges may be deployed by hand or by the smallest of remotely controlled vehicles.Since the Vulcan will disintegrate upon firing, there is no recoil. Freedom from dangerousfragments is an advantage of the plastic body components, thus greatly reducing incidentaldamage behind and to the side of the exploding charges. TheVulcan is supported by means ofaluminium wire legs that can be configured into a bipod or tripod, as the situation allows.Alternatively, the devices may be laid directly on the ground.

Initiation and Body Variants

The detonator well is ordinarily sized to take the British in service L1A1 and L2A1 detonators,standard US military detonators and the detonating cord booster (DCB); it can also acceptcommercial detonators and shock-tube initiators. The system can be adapted to accept othermilitary and commercial detonators, as required.All detonators are held by a universal detonatorholding screw.

The Vulcan Kit is supplied in a pentapod-shaped container and contains:

10 Vulcan Body AssembliesA Loading Tool Set (3 pieces)A pack of 30 Aluminium legs

VULCAN SHAPED-CHARGE KIT




Various Types of Projectile are available. These are selected according to the intendedapplication of the charge. The system can be adapted to accept other military and commercialdetonators, as required. All detonators are held by a universal detonator holding screw.

MAGNESIUM INCENDIARY CONE The jet formed by this cone is less penetrating than thatformed by the copper cone but it is a less powerful initiator of detonation. It is used to penetrateeven thick-walled shells or bombs and ignite the explosive or pyrotechnic filling. For thisapplication the Vulcan is much less likely to cause inadvertent high order detonation than other,more conventional, charges. Vulcan thus provides a reliable means of bringing about a “loworder” deflagration event. The usual explosive load for this purpose is between 30 and 40g.

COPPER CONE Using the jet-forming copper cone, the charge produces a jet which may beused to pierce holes, typically through 75mm (3 in) of mild steel or greater thicknesses of concreteor brickwork. It may be used for causing the detonation or deflagration of steel-cased ammunitionwithout any risk of inadvertent disturbance of the target before firing. The usual explosive load isbetween 20 and 50g.

COPPER EXPLOSIVELY-FORMED PROJECTILE A wide angled copper cone, essentially aslightly domed disc, generates an explosively-formed projectile (EFP) which may be used topenetrate robust targets at much greater ranges than the jet-forming cone. This enables theVulcan to be used as a de-armer and disruptor device. It punctures 10mm thick steel at a rangeof at least 1,500mm.

WATER PROJECTILE Aconical cavity is formed in the explosive, water is poured into the cavity,and a plastic cone is inserted to retain the water. The charge thus becomes a shaped-charge,able to penetrate steel-cased munitions with thicknesses of up to 10mm, and to disperse theircontents with minimal risk of detonation. Charges are quickly assembled and robust.

ALUMINIUM PROJECTILE The aluminum projectile is able to deliver a powerful blow to shellfuses and bomb pistols, thus removing them or jamming their mechanisms. It thus provides alow-priced, disposable alternative to de-armers using heavy steel barrels.

NOZZLE The Nozzle consists of an elongated, plastic cone which fits onto the open end of theVulcan body assembly. This provides a highly pressure-resistant stand-off space and makes itpossible to use the charge as an underwater disruptor which is very much easier for a diver tohandle than are conventional steel underwater disruptors.The nozzle also limits projectile impactto a very restricted zone and greatly facilitates aiming with pin-point accuracy even in conditionsof zero visibility. Integral sights enable the device to be used effectively at great stand-offdistances.TREPANNING ATTACHMENT The Vulcan body may be fitted with a trepanning attachmentwhich enables the charge to cut a disc approximately 37mm in diameter from a munition casefor inspection or flooding.

WATER JACKET The penetration of any of the projectiles can be significantly increased withoutincreased explosive load by application of the water jacket.




The BootBanger is a shaped-charge using detonating cord or

sheet explosive as the propellant and water as the projectile. It

is contained within a plastic briefcase and projects an extremely

disruptive jet of water. The water penetrates the floor, or the

sides, of a vehicle and ejects and disrupts the bomb or explosive

materialswithoutcausingtheir initiation. Thedevice isprovided

empty and is loaded with explosive and water by the user.

The BootBanger was originally designed for the British Army to usein anti-terrorist EOD operatations.

Applications

The BootBanger is typically placed under a vehicle known, orbelieved, to contain a bomb. When activated the BootBanger

projects a jet of water vertically with such force that the bottom of thevehicle is penetrated and the bomb ejected through the boot lid or theroof. The detonating cord is severed by the jet without being initiated.

Delivery to Target

The BootBanger case is only 106mm deep, so may easily be placedunder a car, even with deflated tyres. Two lugs on each on the endof the case allow a pair of prongs attached to a remote-controlledvehicle to carry the BootBanger to the target, deposit it at the chosenpoint, and withdraw, leaving the charge in place. The loaded deviceis light enough for manipulation by small vehicles.

Explosive Load & Performance

The BootBanger's explosive load is variable over a very wide range.Using 10g/metre detonating cord, a typical loading might be 250g ofexplosive. Such a load can be used to blow two aluminium beer kegsfrom the closed boot of a car to a height of approximately 10 metres.The spare wheel is typically also ejected, and a half-full petrol tankruptured and emptied without ignition.

Dimensions & Weights

Size: 440 x 310 x 106 mmApprox. weight empty: 2.3kgApprox. weight full: 19.0kgTotal water content: 13.6 litresVolume of projected water: 6.8 litres

Sheet explosive can be used to give much heavier loadsif required.

BOOTBANGER – VEHICLE WATER DISRUPTOR




Developed for the UK Ministry of Defence, the Dragon is a high temperature pyrotechnic

torch similar to the one used by the British Army for EOD operations. It is designed to

destroy, by means of burning, plastic and thin-cased metal anti-personnel and anti-tank

mines and other ordnance, such as sub-munitions.

Method of Operation

A Dragon is placed close to (but not touching) the target ordnance and then activated electricallyvia a firing cable. Once initiated Dragon produces a high temperature flame that burns throughthe case of the target and burns the explosive fill of the ordnance.

Characteristics

• Burn time 30 seconds• Flame temperature 1000°C• Can penetrate through 3mm of steel• UN Hazard Division 1.3S• Contains no high explosive or detonators• Safe to use, transport and store• Low intrinsic cost compared to high explosives• Minimal training required

DRAGON - PYROTECHNIC TORCH




EOD CRIMPING TOOL

The EOD Crimping Tool is a hand-held tool, which is used for crimping a detonator to a

safety fuse. It is capable of single-handed operation by either right-or left-handed users.

The Crimper is corrosion-resistant and incorporates a wire stripper and cutter, as well a

screwdriver blade.

The EOD Crimper provides crimping facilities for:

? Crimp Igniter Safety Fuse Electric (ISFE) and Safety Fuse? Secure Crimp Detonator Flash L1A1 to Safety Fuse

The EOD Crimping Tool will withstand a pull-off force of 75N and remain intact, and will not impairthe integrityofeither the ISFEor thedetonator. No training is required inorder touse thisequipment.




The Lightweight EOD Response Pack was designed and developed by a serving senior

UK EOD Operator. Rigorous field testing in the Balkans, East and WestAfrica,Afghanistan

and recently Iraq have ensured this product will meet 'real time' requirements of EOD

teams deployed on hostile and demanding operations in harsh climatic conditions.

Designed for a typical two man EOD team, in a light scales role, it provides a significant

sustainable capability, while minimizing weight and bulk. This allows the team to carry an

EOD capability in addition to normal field equipment.

The product utlilises a two pack approach which enhances equipment sharing and also providesproduct segregation which is essential for equipment of an explosive nature (detonators and bulkcharges). The modular design of the kit provides complete flexibility by allowing additionalequipment and explosives to be carried.

The Lightweight EOD Response Pack adheres strictly to EOD doctrine and philosophy andprovides capability in the following EOD operation phases:• Reconnaissance and survey• Search and location• Access• Identification and Diagnoses• Render Safe Procedures• Final Disposal

Additional equipment can be supplied to enhance capability for improvised Explosive DeviceDisposal (IEDD) threats.

Key features include :

• Innovative Hook and line Kit• Advanced Metal detection• Takedown Mine Prodder with hand protection• Search Equipment• Explosive Tools• Modular Construction

The Lightweight EOD Response Pack can be utilised by Police and Military, EOD ImmediateResponse teams, Deployed Light Scale Operations and NGO De-miners/EOD teams. It willprovide a much needed vital capability when a heavy role kit is unsuitable or unavailable whilesimultaneously providing the EOD operator the ability and functionality to react to a full spectrumof EOD tasks, in a practical and significantly safer manner.

LIGHTWEIGHT EOD RESPONSE PACK

NATOSTOCK NO:

1385-99-391-7115




The Backpack- Mounted Hook and Line Kit has been designed to negate the need for an

assortment of hook and line kits. It brings together much of the functionality of the entire

MSI Hook & Line Kit range into one easy-to-deploy backpack. The Backpack-Mounted

Hook and Line Kit comes with a detachable smaller bergen, which is ideal to take forward

for subsequent, smaller, specified tasks.

The kit has been designed in co-operation with British army experts. It includes 100 metres of highstrength Kevlar rope, a range of hooks, anchoring devices and attachment tools, including theadvancedautomaticpulleyopeningsystem.Thissystemallowssuspectdevices tobemaneuveredalong complex routes without the operator having to return to the hazardous area. The kit alsoincludes a selection of search mirrors and telescopic arms.

Contents1. 100M long 5.5mm dia line with snap hook2. Hook, small single plain3. Hook, medium single plain4. Hook, medium double plain x 25. Hook, large single plain6. 25mm eye x 47. Rope sling, 3mm dia x 2m long x 28. Rope sling, 4mm dia x 2m long x 29. Rope sling, 5mm dia x 2m long x 210. Shock cord, 10mm dia x 2m long, soft eye x 211. Shock cord, 10mm dia x 1m long, soft eye x 212. Piton spearpoint 55mm long x 213. Piton spearpoint 80mm long x 214. Piton chisel 55mm long x 215. Piton chisel 85mm long x 216. Self grip forceps x 217. 10 Self grip pliers with eye x 218. Karabiner (alloy) 18mm screwgate 27kN x 419. Door stop plastic wedge x 420. Tools compact set pocket knife x 121. Pulling handle x 122. Rope eye23. 1.5m 4 sec telescopic pole24. Hook spring gate 15mm25. Hook spring gate 50mm26. Light-weight spring grip x 227. Belt sling28. Large IEDnet29. Automatic opening snatch block x 430. Torpedo release31. Sticky eye x 1032. Rope 3mm dia x 100m 3 strand polyester33. 1.6mm dia x 5m long stainless wire x 534. Clear cable tie 368 x 7.6 x 10035. Red cable tie 200 x 4.8 x 10036. Duck tape 50mm x 50m37. Safe-C security mirror38. High intensity pocket torch39. Telescopic inspection mirror with 140mm convex mirror

BACKPACK-MOUNTED HOOK & LINE KIT




725 PA UNDERWATER METAL DETECTOR

The 725 PA Underwater Metal Detector operates on a new pulse induction technique that

provides detailed information on detected objects by means of an audio signal. The Pulse

Analysing (PA) system evaluates the response signals from a located object concerning

its state of decay and characteristic shape.

Small objects with short response signals will cause a continuous indication in the headset. Largeobjects with high conductivity will cause additional pulses, which are indicated in the headset andon the LED display.

ThePAtechnologyallows the 725PADetector tobeusedon interfering,non-cooperativesoil andwill clearly indicate objects with high conductivity despite interference from the ground or fromother close objects.

Total length: 750/1350mmWeight: approx 1.7kg




MINE SHOES

The Mine Shoes are the culmination of years of research and have been designed and

developed by a team who have tested and used them in the field. They represent a totally

unique concept and can be assembled and dis-assembled in seconds. The Mine Shoes

enable the wearer to traverse a minefield over mud, water, or any terrain in safety simply

by slipping the compact unit out of his regulation pack, inflating the air cushions and

continuing on his way in seconds.

The Mine Shoe is the successful result of research and testing. Now in use as part of theregulation army equipment of very IDF soldier and are used by UK EOD teams inAfghanistan andIraq as well as other armies world-wide.

The Mine Shoes are built on the theory of air cushions, which support the body while reducing thepressure in relationship to the minefield. The shoes fold up into a small lightweight package thatcan be easily stored in a rucksack.

The Mine Shoes are made of sturdy nylon, nylon-reinforced PVC, coated aluminium and steelalloys; the five air cushions are of specially designed, patented material created for maximumstrength and resiliency.

Features

? Fully inflatable/deflatable in seconds.? Foldable into a small 360 x 160 x 120mm pack.? Lightweight – 2.3 kilos.? Completely portable.? Made of tough nylon, nylon-reinforced PVC; air cushions of PVC-type L 152.? Upper rigid frame of aluminium and steel alloys.? Self-locking, error-proof device with no moving parts – eliminates maintenance problems.? Metallic parts will not interfere with mine detector apparatus.? Can be used to traverse any terrain: water, mud, swamp, or bush




WD-100 WIRE AND CABLE LOCATOR

The WD-100 Wire and Cable Locator is the latest addition to the MSI range of metal and

cable detectors. The WD-100 is designed to detect the presence of both buried and

surface laid command cables or wires that could be used to activate Improvised

Explosive Devices (IEDs).

The WD-100 is lightweight, durable and easy to operate. It has a unique ergonomic design, whichmeans that the operator can use the unit for long periods over all types of terrain.

The detector is powered by 3 standard LR20 batteries, which provide 8 hours of continuousoperation.

The WD-100 is supplied packed in a sturdy IP67-rated transit case. During operations theequipment can be carried in the haversack, also supplied, which is water-resistant.

Weight: Short version – 0.9kgLong version – 1.2kg

Complete intransit case: 4.0kg




SUN-LITE UNIVERSAL MARKER

The Sun-Lite Universal Marker is a solar-powered flashing LED marker that is designed

to mark hazardous areas or objects. Each marker operates automatically on a dusk-till-

dawn cycle, switching on as soon as it gets dark and switching off at dawn.

Two LED colours are available for the Sun-Lite Universal Marker in red and green. Red isnormally used to mark landmines, unexploded ordnance, booby traps, mine fields and sub-munition strikes. Green markers are used to mark safe routes through a hazardous area.

SPECIFICATIONS

Weight: 25gLength: 85mmWidth: 58mmHeight: 30mmVisual rangenaked eye: 200mFlash rate: .75 - 1 secDiode life: 100,000 hoursCase: stabilised polycarbonate.




The new (Year 2005) Robotic Telescopic Manipulator has been designed in close

consultation with serving British Army EOD experts. It is designed to provide the

operator with a 3 metre stand-off capability, thus significantly increasing operator

survivability should a device detonate. The Robotic Telescopic Manipulator allows EOD

operators to manipulate suspect devices and objects at a stand-off distance of 3 metres.

Tube sectionsare linked together, with a poweredclaw attachmentat the operatingend.The finalsection has a frangible joint, which fails in the event of an unplanned detonation.This ensures theload transferred to the operator is reduced. A fragment shield, forward of the operator, offersextended protection in the event of an unplanned detonation. Acounterweight tube assembly isbehind the operator, which balances the manipulator. The claw opens/closes and rotates underpowered control. The angle is adjusted manually with locking screws.

The manipulator collapses down, and is stored in a 1700 Pelican case.

OPERATIONAL SPECIFICATION:

Distance of operator from claw: 3metresMaximum weight that may be lifted: 15kgManipulator weight, assembled, ready for use: 14kgManipulator weight, collapsed down, and stored in case: 21.5kgClaw maximum opening: 200mmClaw rotation: 360 degrees continuous

CONSTRUCTION

SPECIFICATION:

Claw:

Material: 6082AluminiumFinish:Anodised

Tube

Material: 6082 aluminium,Finish:AnodisedNumber of tubes: 8Number of tubes forward of operator:5Tube connecters: Polyacetal taperedlocking collars

Electrical connecters/wire

Material: Polyacetal, gold plated brass, gold plated phosphor bronzeWire: 5Amp, 24 strand 0.2 diameterClaw Control specification:Claw open/close and rotate functions: Non-latching toggle switchesOn/off control: Latching toggle switchContinuity test: Non-latching toggle switchAdjustable load control: Potentiometer

Counterweight

Material: Stainless steelMass: 10kg

Motor specification

Style: Carbon brushStall current: 9A

ROBOTIC TELESCOPIC MANIPULATOR

Charger specification:

Input:110V/240VPlug style: To suit end user

Battery specification

12V 3Ah Nickel metal Hydride

NATOSTOCK NO:

1385-99-905-07663




Documents

MSI Product Catalog