Ms 1651 Disassemble Sop

GX620 （MS-1651）Disassemble SOP

■ 1、Battery Pack

■ 2、BOTTOM DOOR ASSY

■ 3、THERMAL-KIT And CPU Module

■ 4、RAM、WLAN And TUNER Module

■ 5、HDD Module ASSY

■ 6、ODD Module ASSY

■ 7、HINGE COVER ASSY

■ 8、UP CASE ASSY

■ 9、LOWER CASE ASSY

■ 10、LCD MODULE ASSY

GX620&MS-1651 Disassemble SOP

■ 1、Battery Pack

1-1：Push the battery Unlock button as below;

1-2：Push the battery Release button as below, then slide the battery pack out of the slot;

NO. Part Name Part No. Qty

1 Battery Pack S9N-0366200-SB3 1


■ 2、BOTTOM DOOR ASSY

2-1：Remove 2pcs M2.5*5mm Screws; Note：Screw driver torque is 2.0~2.5kgf.cm

2-2：Remove Bottom Door Assy as below;


2-3：Remove SIM Card Door as below;


1 Screw E43-1255001-H29 2

2 SIM CARD DOOR E2P-6510511-Y31 1

2 BOTTOM DOOR ASSY 307-651J411-Y31 1


■ 3、THERMAL-KIT And CPU Module

3-1：Remove 7pcs SPING Screws, Then Disconnect CPU Fan sink Cable; Note：Screw driver torque is 2.0~2.5kgf.cm

6 5

2

1 3

7 4

3-2：Remove CPU Fan sink;


1 CPU FANSINK E32-0900531-F05 1


3-3： Open CPU slot as below;

3-4：Remove CPU Module;


1 CPU Module A09-2520106-I06 1

GX620&MS-1651 Disassemble SOP 3-5：Remove 2pcs M2.5*5mm Screws;

Note：Screw driver torque is 2.5~3.0kgf.cm

3-6：Remove VGA Card Module;


1 VGA CARD Module 602-V114-06S 1

2 Screw E43-1255001-H29 2


■ 4、RAM、WLAN And TUNER Module

4-1：Push RAM Slot Fastener as below;

4-2：Remove RAM Module;


1 RAM Module S7C-S347701-T10 2


4-3：Remove WLAN Card Antenna, Then remove 1pcs M2*3mm Screw; Note：Screw driver torque is 1.8~2.2kgf.cm

4-4：Remove WLAN Card Module;


1 WLAN CARD Module S57-0800180-I06 1

2 Screw E43-1203003-H29 1


4-5：Remove Tuner Antenna, Then remove 1pcs M2*3mm Screw; Note：Screw driver torque is 1.8~2.2kgf.cm

4-6：Remove Tuner Module;


1 TUNER Module S36-0000610-K45 1

2 Screw E43-1203003-H29 1


■ 5、HDD Module ASSY

5-1：Remove 2pcs M2.5*5mm Screws Then remove HDD Door Assy as below; Note：Screw driver torque is 2.0~2.5kgf.cm


1 Screw E43-1255001-H29 2

2 HDD DOOR ASSY 307-651K411-Y31 1


5-2：Remove HDD Module as below;


1 Screw E43-1255001-H29 1


5-3：Remove 2pcs M3*3.5mm Screws Then remove HDD Bracket as below; Note：Screw driver torque is 2.0~2.5kgf.cm


1 Screw E43-1303501-H29 2

2 HDD Bracket 307-6510111-Y28 1

3 HDD MODULE ASSY S71-2425504-F06 1


■ 6、ODD Module ASSY

6-1：Remove 1pcs M2.5*5mm Screw Then remove ODD Module Assy as below; Note：Screw driver torque is 2.0~2.5kgf.cm


1 Screw E43-1255001-H29 1


6-2：Remove ODD Bezel as below;


1 ODD Bezel E2P-651F211-Y31 1


6-3：Remove 2pcs M2*3mm Screws Then remove ODD Bracket as below; Note：Screw driver torque is 1.5~1.8kgf.cm


1 Screw E43-1203007-H29 2

2 ODD Bracket E2M-6510211-Y28 1


■ 7、HINGE COVER ASSY

7-1：Push Fastener as below;

GX620&MS-1651 Disassemble SOP 7-2：Remove Hinge Cover as below;


1 HINGE COVER 307-651E111-Y31 1


7-3：Remove Hinge Cover Cable as below;


1 POWER BOARD 607-1651B-C10 1


7-4：Remove Cap Sensor Board as below;


1 Cap Sensor Board 607-1651D-C10 1


7-5：Remove Cap Sensor Board as below;


1 Cap Sensor Board 607-1651D-C10 1

2 Cap Sensor Board Cable K1C-1012023-J36 1


■ 8、UPCASE ASSY

8-1：Remove 5pcs M2*3mm Screws, Then remove Keyboard as below; Note：Screw driver torque is 1.5~2.0kgf.cm


1 Screw E43-1203003-H29 5

2 Keyboard S1N-3UTC131-C54 1


8-2：Remove 2pcs M2*3mm Screws, Then remove Power Board as below; Note：Screw driver torque is 1.5~2.0kgf.cm


1 Screw E43-1203003-H29 2

2 Power Board 607-1651B-C10 1


8-3：Remove 13pcs M2.5*5mm Screws, Then remove 2pcs M2.5*7mm Screws; Note：Screw driver torque is 2.0~2.5kgf.cm


1 Screw E43-1255001-H29 13

2 Screw E43-1257001-H29 2


8-4：Remove PCI-E Card And XD Card as below;


1 PCI-E Card E2P-6510411-Y31 1

2 XD Card E2P-6510611-Y31 1


8-5：Disconnect Speaker Cable and Microphone Cable as below;


1 Speaker Cable S33-A020200-F33 1

2 Microphone Cable S34-2100580-F33 1


8-6：Remove FFC Cable(TO Audio Board) and FFC Cable(TO M/B) as below;


1 FFC Cable(TO Audio Board) K1C-1020003-J36 1

2 FFC Cable(TO M/B) K1C-1012024-J36 1


8-7：Remove 2pcs M2*3mm Screws, Then remove FFC Cable(TO M/B)&(TO Button) as below; Note：Screw driver torque is 1.5~2.0kgf.cm

8-8：Remove Touchpad Bracket;


1 Screw E43-1203003-H29 2

2 FFC Cable(TO Button) K1C-1012025-J36 1

3 Touchpad Bracket E2M-6510911-Y28 1


8-9：Remove 1pcs M2*3mm Screw, Then remove Touchpad Button Board; Note：Screw driver torque is 1.0~1.5kgf.cm


1 Screw E43-1203003-H29 1

2 Touchpad Button Board 607-1651C-C10 1


8-10：Remove FFC Cable (TO Button) as below;


1 FFC Cable(TO Button) K1C-1012025-J36 1

2 Touchpad Module S78-3700360-SD2 1


■ 9、LOWER CASE ASSY

9-1：Remove 1pcs M2.5*5mm Screw, Then remove FFC Cable (TO Audio Board) as below; Note：Screw driver torque is 2.3±0.2kgf.cm

9-2：Remove FFC Cable (TO Power Board) as below;


1 Screw E43-1255001-H29 1

2 FFC Cable(To Audio Board) K1C-1020003-J36 1

3 FFC Cable(To Power Board) K1C-1018003-J36 1


9-3：Remove RJ11 Cable and Bluetooth Cable as below;

9-4：Remove M/B;


1 RJ11 CABLE K10-3002110-H58 1

2 BLUETOOTH CABLE K10-3008077-H39 1

3 M/B 607-16511-B10 1


9-5：Remove 1pcs M2*3mm Screw, Then remove Bluetooth Antenna; Note：Screw driver torque is 1.0~1.5kgf.cm


1 Screw E43-1203003-H29 1

2 BLUETOOTH ANTENNA S79-1800890-V03 1

3 BLUETOOTH MODULE 605-6837D-070 1


9-6：Remove 2pcs M2*3mm Screws, Then remove Audio Board; Note：Screw driver torque is 1.0~1.5kgf.cm


1 Screw E43-1203003-H29 2

2 AUDIO BOARD 607-1651A-C10 1

3 LOWER CASE ASSY 307-651D411-Y31 1


9-7：Remove Bluetooth Antenna、RJ11 Cable and TV IO Jack;


1 BLUETOOTH ANTENNA S79-1800890-V03 1

2 RJ11 CABLE K10-3002110-H58 1

3 TV IO JACK K19-3001017-H39 1


■ 10、LCD MODULE ASSY

10-1：Disconnect Camera Cable as below;


1 Camera Cable K10-3006056-H39 1


10-2：Remove 2pcs M2.5*5mm Screws; Note：Screw driver torque is 2.0~2.5kgf.cm

10-3：Use Plastic Stick Push Hinge Cap as below;


1 Screw E43-1255001-H29 2

2 Hinge Cap_L E2P-6511311-Y31 1

3 Hinge Cap_R E2P-6511411-Y31 1


10-4：Draw Out Camera Cable、Wireless Antenna and 3G Antenna as below;


1 3G Antenna S79-1800780-V03 1

2 Wireless Antenna_L S79-1800800-V03 1

3 Wireless Antenna_R S79-1800790-V03 1


10-5：Disconnect Coaxia Cable as below;


1 Coaxia Cable K19-3040006-H39 1


10-6：Remove 2pcs M2.5*7mm Screws; Note：Screw driver torque is 3.5±0.2kgf.cm


1 Screw E43-1257001-H29 2


10-7：Remove 8pcs LCD Rubbers Then remove 8pcs M2.5*5mm Screws; Note：Screw driver torque is 2.0~2.5kgf.cm


1 LCD Rubber E2Y-6510111-Y40 8

2 Screw E43-1255001-H29 8


10-8：Remove LCD Bezel as below;


1 LCD BEZEL 307-651B411-Y31 1

GX620&MS-1651 Disassemble SOP 10-9：Remove 6pcs M2.5*5mm Screws, Then remove Left And Right Hinge;

Note：Screw driver torque is 2.0~2.5kgf.cm


1 Screw E43-1255001-H29 6

2 Hinge_Left E2M-6510411-G60 1

3 Hinge_Right E2M-6510711-G60 1


10-10：Remove Inverter Cable, Then remove Display Module;


1 Display Module S1J-690A004-S02 1


10-11：Remove Inverter Module、3G Antenna、WLAN Antenna;


1 INVERTER S78-3300450-SG3 1

2 Wireless Antenna_R S79-1800790-V03 1

3 Wireless Antenna_L S79-1800800-V03 1

4 3G Antenna S79-1800780-V03 1


10-12：Remove CMOS Camera Module as below;


1 CMOS Camera Module S1F-0003020-C54 1

2 Camera Cable K10-3006056-H39 1

3 LCD Cover Assy 307-651A511-CG0 1


10-13：Remove Coaxial Cable as below;


1 Coaxial Cable K19-3001017-H39 1

2 Display Module S1J-690A004-S02 1


10-14：Remove 8pcs M2*3mm Screws, Then remove LCD Bracket as below; Note：Screw driver torque is 1.5~2.0kgf.cm


1 Screw E43-1203007-H29 1

2 LCD Bracket_Left E2M-6510511-Y28 1

3 LCD Bracket_Right E2M-6510611-Y28 1

GX620 （MS-1651）screws specification

Photo Screw specification Label

(M2.5*L5MM) black

(M2*L3MM)white

(M3*L3.5MM) white

(M2.5*L7MM) black

GX620 （MS-1651）screws specification ■ 1、BOTTOM DOOR ASSY total 18Pcs M2.5*5 and 2pcs M2.5*7 screws, ■ specification：

Photo Screw specification

label

(M2.5*L7MM) black

(M2.5*L5MM) black

GX620 （MS-1651）screws specification ■ 2、THERMAL-KIT total 7pcs spring Screws

6

5

1

42

3

7

GX620 （MS-1651）screws specification ■ 3、TUNER, WIRELESS ,MDC CARD and HDD ASSY total 8Pcs screws, ■ specification：

Photo Screw specification label

(M3*L3.5MM) white

(M2*L3MM)white

GX620 （MS-1651）screws specification ■ 4.UPCASE ASSY total 13pcs screws , ■ specification：

Photo Screw specification Label

(M2*L3MM)white

(M2.5*L5MM) black

GX620 （MS-1651）screws specification ■ 5.LCD Bezel total 8pcs screws, ■ specification：


(M2.5*L5MM) black

GX620 （MS-1651）screws specification ■ 6. LCD MODULE ASSY total 14cs screws

■ specification：


(M2.5*L5MM) black

(M2*L3MM)white

GX620 （MS-1651）screws specification ■ 7. UPCASE and LOWER CASES total 3pcs screws，

■ specification：


(M2*L3MM)white

GX620 （MS-1651）screws specification ■ 8、NB total 1pcs screw， ■ specification：


(M2.5*L5MM) black

GX620 （MS-1651）screws specification ■ 9. Bluetooth and Audio Board 3pcs screws ■ specification：


(M2*L3MM)white

GX620 （MS-1651）screws specification ■ 10. Touch Pad Board total 3pcs screws ■ specification：


(M2*L3MM)white

Documents

Ms 1651 Disassemble Sop