Upload
feruz-atan
View
221
Download
21
Tags:
Embed Size (px)
Citation preview
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 1 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Equipment and Materials Source List Malaysian Project Design Specification
MPDS 00-99-01
1 1 Apr 2011 Update and Sections Additions RMS LBW LBW DCS
0 23 Nov 2010 Initial Publish RMS LBW LBW DCS
Rev. Issue Date Description Document Custodian
Endorser System
Administrator System Owner
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 2 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Scope
This Malaysian Project Design Specifications (MPDS) contains the names of acceptable product
manufacturers, which shall be used by Fabricators, Contractors and Equipment Packagers to
procure equipment/materials in the listed category for supply to EMEPMI. Notwithstanding the
above, purchase of products from these manufacturers is still subject to the products meeting the
required delivery date and complying with relevant EMEPMI specifications.
Purchase of equipment/materials from other manufacturers not specified herein is a deviation to
this Malaysian Project Design Specifications (MPDS) and shall require prior EMEPMI approval.
EMEPMI approval may be granted under any of the following conditions:
a) Product cannot be sourced from the listed manufacturers.
b) Deviation will result in a significant improvement to project schedule.
c) Deviation will result in a significant cost saving (vs. buying from listed manufacturers), whereby a portion of that cost shall be reimbursed to EMEPMI.
This data is supplied to aid the Fabricator, Contractor and Packagers in determining who the
Malaysian Agent is for each products manufacturer listed. It is the Fabricator's responsibility to
ensure that the manufacturers listed have local agents and are registered with PETRONAS.
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 3 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Table of Contents
1. Required References ............................................................................................ 5
1.1. Company Technical Sheet ........................................................................... 5
2. Definitions.............................................................................................................. 5
3. Corrosion Protection ............................................................................................ 5
4. Rotating Machinery............................................................................................... 7
5. Mechanical – Static ............................................................................................. 12
6. Pressure Vessels ................................................................................................ 15
7. Heat Exchangers ................................................................................................. 17
8. Mechanical Valves .............................................................................................. 19
9. Process Piping .................................................................................................... 22
10. Process Equipments........................................................................................... 24
11. Fire Protection..................................................................................................... 29
12. Life Safety ............................................................................................................ 30
13. Flare System........................................................................................................ 32
14. I&C........................................................................................................................ 32
15. Telecom................................................................................................................ 44
16. Electrical .............................................................................................................. 46
17. Structural & Architectural................................................................................... 52
18. Marine................................................................................................................... 53
19. Surf (Marine) ........................................................................................................ 55
20. Forging................................................................................................................. 57
21. Duplex Stainless Steel ........................................................................................ 62
22. Upstream Acceptable Manufacturers of Structural Plate, Shape and Tubular Products............................................................................................................. 111
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 4 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Record of Change ..................................................................................................... 112
Attachment: Purpose Codes Definitions................................................................ 113
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 5 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
1. Required References
This Section lists Practices and Standards that are generically referenced and assumed to be a part of this
document. Unless otherwise specified herein, use the latest edition.
1.1. Company Technical Sheet
TS 29-01-09 Upstream Acceptable Manufacturers of Structural Plate, Shape and
Tubular Products.
2. Definitions
Yellow Highlighted Lines = Supplier has been put on the Watch List due to performance
issues or there is important information that needs to be considered before a decision is made to use them. Please review prior to placing an order.
Red Highlighted lines = Do not use. Supplier has performance issues
3. Corrosion Protection
Category Description Manufacturer Remarks
Cathodic Protection Systems
Engineering and Installation Cathelco Group Corrosion Service Corrpro Matcor Nakabotec
Pipelines, Facilities, and Structures
Coatings and Linings FBE Coating Applicator Bayou Pipe Coating / CCSI Bredero Shaw Commercial Resins Co. EUPEC PPSCH Socotherm
Pipelines, Flowlines, Induction Bends
FBE Field Joint Coating Applicator
Bredero Shaw Commercial Resins Co. EUPEC Pipeline Induction Heat Ltd. (PIH) Socotherm Socotherm Bayou Pipe Coating / CCSI
Pipelines and Flowlines
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 6 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
FBE Powder Manufacturer 3M BASF Dupont Jotun
Multi layer Insulation Coatings Bredero Shaw PPSCH Pipelines and Risers Multi layer Insulation Coatings
Applicator Socotherm Pipelines and Risers
Multi-Layer Polyolefin Coating (3 Layer PE and PP) Applicator
Socotherm Pipelines and Risers
Multi-Layer Polyolefin Coatings Bredero Shaw EUPEC PPSCH
Pipelines and Risers
Pipelines, Facilities, and Structures
Carboline Hempel International Coatings Jotun Sherwin Williams PPG
Polychloroprene Applicator Socotherm Risers Polychloroprene Coating Baker Rubber
Bredero Shaw Mark Tool Company PPSCH Trellborg Viking
Risers
Polyethylene Jacketed Polyurethane Foam Insulation
Bredero Shaw Logstor A/S
Pipelines and Flowlines
Polyurethane Foam Infill Coating Applicator
Offshore Joint Services (OJS) Pipeline Induction Heat Ltd. (PIH) EUPEC
Pipelines
Subsea Insulation Bayou Flow Technologies Bredero Shaw Trelleborg Offshore
Weight Coating Bayou Pipe Coating Bredero Shaw EUPEC PPSCH
Pipelines and Flowlines
Weight Coating Applicator Socotherm Pipelines and Flowlines Corrosion Inhibitors Amtech Chemical Sdn
Bhd Maces Sdn Bhd Premier Enterprise Corporation (M) Sdn Bhd
Corrosion Monitoring Equipment
Pipelines, Facilities, and Structures
Caproco Cormon Corrocean Deepwater Corrosion Services Rohrback-Cosasco
Electrical Isolation Monolithic Isolation Joint ALFA Engineering Zunt
Fluoropolymer Bolt Coatings
Pipelines, Facilities, and Structures
Asemco Co. Custom Coating Applicators E/M Coating Services High Technology
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 7 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Coating Company International Polymer Lone Star Fasteners Praxair/Smaltirivia Seng Heng Engineering PTE Southwest Plating Southwest Impregion Fluid Sealing Products Allegheny Coating American International Industries Southern Bolts and Nuts Sdn Bhd Status Head Sdn Bhd
Sacrificial Anodes Pipelines, Facilities, and Structures
CP Tech Galvotec Impalloy Metec Samgong Skarpenord Wattyl Dimet MPE
4. Rotating Machinery
Category Description Manufacturer
Axial Compressors Demag Delaval Sulzer Centrifugal Compressors
API 617 Dresser-Rand Co Sulzer
Elliot-Ebara GE / Nuovo Pignone Ebara International / Elliot Turbomachinery Co Ltd Demag Delaval
GHH Borsig Mitsubishi Heavy Industries Rolls-Royce
High Speed / Low Flow Sundyne Corp Modular Construction Solar Turbines Inc Centrifugal Pumps ANSI Self Priming Gorman Rupp ANSI Solids Handling Gorman Rupp ANSI - Water Services Flowtronex PSI Inc. ANSI Ruhrpumpen Clyde Union (Weir Pump, Ltd.) Flowserve Corp
Pump Division ANSI Vertical David Brown Union Pumps API 610 BB1 Ebara Corp Flowserve / Worthington SPA
Flowserve Corp Pump Division Sulzer Pumps
Ruhrpumpen David Brown Union Pumps Nuovo Pignone Shin Nippon Machinery Co Ltd
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 8 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
CPC Pumps International API 610 BB2 Ebara Corp Flowserve / Worthington SPA
Flowserve Corp Pump Division Sulzer Pumps Clyde Union (Weir Pump, Ltd.) Weir Gabbioneta Pumps
David Brown Union Pumps Nuovo Pignone Shin Nippon Machinery Co Ltd CPC Pumps International Ebara Corp Goulds Pumps Ruhrpumpen
API 610 BB3 Flowserve Corp Pump Division Sulzer Pumps Clyde Union (Weir Pump, Ltd.)
David Brown Union Pumps Nuovo Pignone Goulds Pumps
API 610 BB4 Flowserve Corp Pump Division
Nuovo Pignone Ebara Corp
API 610 BB5 Flowserve Corp Pump Division Clyde Union (Weir Pump, Ltd.)
Sulzer Pumps David Brown Union Pumps Nuovo Pignone Ebara Corp
API 610 OH1 Flowserve / Worthington SPA Flowserve Corp Pump Division
Goulds Pumps API 610 OH2 Flowserve Corp
Pump Division Flowserve / Worthington SPA Clyde Union (Weir Pump, Ltd.)
Sulzer Pumps David Brown Union Pumps Shin Nippon Machinery Co Ltd CPC Pumps International Ruhrpumpen
API 610 OH3 Flowserve Corp Pump Division
David Brown Union Pumps CPC Pumps International
API 610 OH4 Flowserve Corp Pump Division
Goulds Pumps David Brown Union Pumps Niigata Worthington Co Ltd CPC Pumps International
API 610 OH5 Flowserve Corp
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 9 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Pump Division Clyde Union (Weir Pump, Ltd.)
Sundyne Corp API 610 OH6 Nikkiso
Sundyne Corp API 610 VS1 Flowserve Corp
Pump Division Sulzer Pumps David Brown Union Pumps API 610 VS2 Flowserve Corp
Pump Division Sulzer Pumps David Brown Union Pumps
Ebara Corp API 610 VS3 Flowserve Corp
Pump Division Sulzer Pumps Clyde Union (Weir Pump, Ltd.) API 610 VS4 Ebara Corp Flowserve (AUSTRIA) Gmbh
Flowserve Corp Pump Division
API 610 VS5 Ebara Corp Flowserve (AUSTRIA) Gmbh
Flowserve Corp Pump Division
API 610 VS6 - Cryogenic Ruhrpumpen API 610 VS6 - General Service Sulzer Pumps API 610 VS6 Clyde Union (Weir Pump, Ltd.) David Brown Union Pumps
API 610 VS7 Sulzer Pumps API 610 Water Services Sulzer / Johnston Pump API 674 Reciprocating David Brown Union Pumps API 685 Sealless Sulzer Pumps Sundyne Corp./Kontro Firewater Service
Flowserve Pte Ltd Flowserve Corp Pump Division Clyde Union (Weir Pump, Ltd.)
Sulzer / Johnston Pump Sulzer Pumps
Firewater Service - Engine Driven Main Firewater Pump
Goulds Pumps
Main Oil Line
Blakers Pump Engineers TKL (S/P) United Pumps
Sealless Hermitic Pumps Inc
Seawater Lift Pumps - Firewater Pumps
Frank Mohn Flatoy AS (Framo)
Slurry GIW (Georgia Iron Works) Weir Minerials North America
Submersible HP Reda (Pumps & S/P) Submersible LP Grunfos Compressor Components
Bearing / Bushings - Swivel Bearings
Avon Technical Products Rotek
Bearing / Bushings - Turntable Bearing
Rotek Rothe - Erde Avon Technical Products
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 10 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
SKF
Compressor Seals - Dry Gas Flowserve Corp Pump Division John Crane Company LLC
Compressors Instrument Air Atlas Copco Process Air and Gas Toromont Process Systems Inc Utility and Instrument Air Tide Air Inc Couplings API 671 Lucas Aerospace Metastream General Service Metastream
Thomas Fans Buffalo Forge Fan Company
Howden Buffalo Gas Turbines Aeroderivitive - LM 2500 GE / Nuovo Pignone Gas Turbine Air Inlet Filters
AAF Altair Donaldson
Gas Turbine Fire Suppression - Water Mist System
Eusebi
Generator Driver Rolls-Royce Solar Turbines Inc
Mechanical Driver - Power Turbines Dresser-Rand Co Mechanical Driver Rolls-Royce
Siemens Industrial Turbomachinery Solar Turbines Inc
Gears API 613 Flender Renk Lufkin Industries Inc. MAAG
Package Lube Oil Systems
Gerhardts TF Hudgins
Pumping Systems
DXP Sepco Ind AGI Industries Capital Process Equipment
Standby / Emergency / Essential Generator
Tractors Malaysia
Turbine Wash Water System Bob J Johnson & Associates Inc Positive Displacement Pumps
API 674 Reciprocating Cat Pumps
Peroni Pompe SpA API 675 Controlled Volume American Lewa
Bran+Luebbe Inc Milton Roy Pulsafeeder Lewa
API 676 Rotary Axflow S.A.S IMO Pump Roper Warran Pump
API 676 Rotary - Multiphase Bornemann API 676 Rotary - MPP Leistritz Corporation Chemical injection Texsteam Diaphragm Goulds Pumps
Texas Process Equipment Diaphragm - Air Operated Haskel Australasia P/L
Warren-Rupp/Sandpiper Wilden
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 11 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Diaphragm - Air Operated Transmark FCX Pty Ltd Diaphragm - Double Diaphragm
Pumps Winston Engineering Corp. SDN BHD
Gear Pump Northern Piston Duraqual
Milton Roy Morgan National Wheatley/Mono
Progressive Cavity
Allweiler Pump Mono Flow Moyno Inc Netzch Roper
Rotary Non API Viking Pump Pump Components Replicated Pump Parts Refine Engineering Seals Mechanical Flowserve Corp
Pump Division ProEight Offshore Engineering Sdn Bhd Seals Packing EGC
Utex Seals John Crane Company LLC Pumps ANSI Gasco Wheatley
Kinecor Inc Booster TKL (S/P)
United Pumps Booster Weir Engineering Diesel Circulating
Viking Pump Worthington
Utility - Potable Water / Hot Water Circ
Ajax Davey Onga Regent
Reciprocating Compressors
API 618 Neuman-Esser USA Inc Dresser-Rand Co Cooper Compression
GE / Nuovo Pignone Danmar Industries Inc
Reciprocating Engines
Diesel Pon Power Papendrecht Caterpillar
Reciprocating Compressors
Diaphragm Type
Burton Corblin
Medium Speed Ariel Corporation Rotary Compressors
API 618 Helical - Air Only
Atlas Copco
Ingersoll Rand Company (Ingrand ACG.) API 618 Helical A-C Compressor
GE Power Systems Airdyne Danmar Industries Inc
GHH Borsig Howden Process Compressor
Process Air and Gas - Helical Kobe Steel Ltd Process Air and Gas - Wet Screw Ingersol-Jati Malaysia
Kobe Steel Ltd Steam Turbines API 611 Dresser-Rand Co
Ebara International / Elliot Turbomachinery Co Ltd API 612 Dresser-Rand Co
Mitsubishi Heavy Industries
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 12 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Ebara International / Elliot Turbomachinery Co Ltd Instrument Air Gardner Denver
5. Mechanical – Static
Category Description Manufacturer
Air Conditioning / HVAC York Alam Dingin Air Conditioning Engineering Sdn Bhd Dynac Sdn Bhd
Hull Only Carrier Marine & Offshore Alscott Air Systems Ltd
ABB Process Industries Direct Engineering Services DWD International LLC Hi Press Trane Tyco Australia Pty Ltd Direct Engineering Services (DES) Borg Warner
Cartridge Filter Package Peco Cranes Bridge and Jib Gaffey Cranes/ Parts and Repairs Kenz Cranes BV Hoist - Monorail Ingersoll-Rand
Beebe C-M
Pedestal Applied Hydraulics Favelle Favco Hochang Machinery Kenz Cranes BV Hydralift Hydralift / Molde Crane AS Hydralift ASA - National Oilwell Norway AS Liebherr Oil States Industries Stalprodukter Nautilus Unit Mariner Skagit Baker Marine SeaKing Weatherford Handal Offshore Services Sdn Bhd MS Herkules Sdn Bhd
Demethanizer Bottoms Flowserve Corp Pump Division
Diesel oil purifier Alfa Laval Elevators Champion Elevators Inc Filters Cartridge Filter Package Cuno Filters
Gameco Pall Australia Peco Plenty Filtration UK Process Materials P/L Southwest Filter Co Winston Manufacturing
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 13 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Hatfield AMF Reda Dollinger Daeham Kingtool Kvaerner Process Systema Baker Hughes Filtan Peerless Anderson
Cartridge Filter Package - Sulfate Removal
Natco Process
Process Filters / Elements Camfil Pty Ltd Cuno Filters Gameco Pall Australia Process Materials P/L USF Filtration Ltd Veolia Water Systems Vilair-AAF Velcon Peco
Quarters - Air Conditioning Haden Engineering Pty Ltd Fuji Filter Mfg Co Ltd
Foam Skid Chemetron Chubb/National Foam Dooley Tackaberry
Fuel Packages Diesel Centrifuge Fuel Package Alfa Laval Flowtronex PSI Inc. Westfalia Separator
Helifuel Package Flowtronex PSI Inc. HVAC Systems Custom Air Products & Services Inc Hydrocyclones Apex Process Systems
Krebs Engineering P/L Baker Process a Divn of Baker Hughes Aust Natco Process
Lube Oil Supply Package Flowtronex PSI Inc. Material Handling Equipment
Certex
Mixers Mechanical Driven Plenty Mixers (Lightnin) Nitrogen Gas Generator Air Products A/S Offspec Oil Heater Sung Jin Geotec Co. Ltd Oil Spill Clean Up Equipment
Crucial Inc
Pig Launcher / Receiver ClampOn AS Taylor Forge TD Williamson Inc Pipeline Equipment Co Sagebrush Pipeline Equipment Shaw Group SWECO Fab Inc
Pig Receiver Pipeline Onshore Fai Officine Di Carvico Potable Water Pressurizing Package
Bob J Johnson & Associates Inc
Pressure Water Sets Fisher Industries Production Manifold Dresser
FMC Seal Gas Cooler Sung Jin Geotec Co. Ltd
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 14 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Slug Catchers Finger Type - 5000 bbl, nominal 4.0 Gscfd wet gas (2&3 phase) up to 99# ASNI
Taylor Forge CMP Dunkerque
Tanks Atmospheric Tanks CB&I Constructors Pty Ltd CB&I Eastern Anstalt
LNG Storage I.H.I. Non Hazardous Open Drain
Separator Tank Natco Process Hitachii Zosen Mechanical Corp
Floating Roof HMT Inc TEG Regen Package Prosernat Utility Vessel Package Heat Exchangers International
Kvaerner Process Systems US Inc. Prosernat En-Fab Inc Natco Process Sung Jin Geotec Co. Ltd
UV Sterilizer Package Bob J Johnson & Associates Inc Washdown Package HP Hot Water Wash Down Package John Zink Company, LLC Washdown Package AGI Industries
Petrex Flowtronex PSI Inc. Hydromeca
Waste Heat Recovery Tulsa Heaters Inc GE / Nuovo Pignone Deltak LLC
Waste Incinerators Natco Process Zeeco
Waste Removal Trash Compactor Enviro-Pak Compactors Waste Treatment Sewage Treatment Package Electrocatalytic Ltd
Red Fox Environmental Services Inc Fast / Smith and Loveless Inc Marine Equipment DIvision
Waste Treatment CETCO Environmental Offshore Service Christ Kennicott Water Technology Ltd
Waste Treatment Equipment
Anderson Water Systems Aquatech Ecodyne
Water Purifiers Alfa Laval Watermakers Distillation Alfa Laval
Beaird Industries High Purity Wash Water Skid C'treat Offshore Inc Potable Watermaker Skid 1 & 2 C'treat Offshore Inc Reverse Osmosis C'treat Offshore Inc
Aquachem Permutit Village Marine Bob J Johnson & Associates Inc
Wet Air Receiver Sung Jin Geotec Co. Ltd Absorber Hitachii Zosen Mechanical Corp Chemical Injection Package
Lewa Milton Roy McFarland Pulsafeeder Texsteam William FMC Bran Leubbe Wilden Haskel
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 15 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Checkpoint Methanol / Hypochlorite Flowtronex PSI Inc.
Bran+Luebbe, Inc Flowtronex PSI Inc. Milton Roy & Blakers Pump Engineers
Cooling Medium Emergency Air Cooler
GEA Rainey Corp
Fuel Oil Filtration Package FiltraTech Gas Dehydration and Gylcol Regeneration Packages
Prosernat Natco Process
Heaters Fired <100MBTU Foster Wheeler USA Fired Heater Div Tulsa Heaters Inc
Fired Optimized Process Furnaces
Industrial Steam Boiler up 1500 psig, up to 240 tonnes/hr modular/up to 315 tonnes/hr field erected
Macchi Steam & Power Generation
Liquid Incinerator John Zink Company, LLC Zeeco
Multimedia Filter Package Natco Process Tower Internals High Capacity Mesh and Vanes Koch-Otto York Trays and Packing
- Mercury Bed Calgon Carbon Co. UOP
Trays and Packing KochGlitsch Sulzer Chemtech AG Sulzer Chemtech PTE Ltd Sulzer Chemtech USA Inc Raschig GMBH UOP
Cyclones Burgess Manning High Capacity Mesh Amistco
Burgess Manning CDS KnitMesh
Vanes Amistco Burgess Manning CDS KnitMesh Peerless
Y Strainers Texas Steam Equipment Aitken Inc Barton Firtop Fuji Filter Mfg Co Ltd Eurofiltec Delmar Hayward Harfield Leslie Nicholson Zurn
6. Pressure Vessels
Category Description Manufacturer
Large Diameter / Heavy Wall Pressure Vessel
Carbon Steel Vessel/Column (Up to 35mm Thickness) - Over 60mm or Over 100ton
Doosan Mecatec
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 16 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
CS up to 150mm thk Sewon Collentech - S Korea
CS/W SS Clad up to 150mm thk Sewon Collentech - S Korea
Cyrogenic Deethanizer Tower ATB Acciaieria e Tubificio di Brescia S.P.A. Beaird Industries Belleli Energy c/o The Hanover Co Felguera Caldereria Pesada S.A. Larsen and Tourbro Ltd
Large Diameter / Heavy Wall Pressure Vessel
Desalter Natco Process
SS up to 150mm thk Sewon Collentech - S Korea
ADI (Australian Defence Industries) ASC Engineering P/L Fusion Weld (address on Project basis) Fitzroy Engineering (NZ) L & A Pressure Welding ATB Caldereria Beaird Industries Belleli Bosco Duro Felguera General Welding Hitachii Zosen Mechanical Corp I.H.I. Japan Steel Mitsubishi Heavy Industries Hyundai
Natco Process Pressure Vessels <2" Sung Jin Geotec Co. Ltd Natco Process API 650 Tanks Saunders International P/L ASME Kvaerner Process Systems US Inc.
Prosernat ASME - Div 1 and AS1210
Supplement 2 ASC Engineering P/L Fitzroy Engineering (NZ) L & A Pressure Welding
C.M. Expansion Tank Sung Jin Geotec Co. Ltd Carbon Steel <600 psi KNM Process Systems Sdn Bhd Carbon Steel >600 psi KNM Process Systems Sdn Bhd Carbon Steel Vessel / Column Sewon E & T Corp Carbon Steel Vessel / Column Up
to 50mm Thickness PT Daekyung Indah Heavy Industry
Closed Drain Flash Drum Sung Jin Geotec Co. Ltd CS - Up to 100mm thickness Ningbo Tianyi CS - Up to 100mm thickness,
limited to 1200mm in diameter Nanjing Chemical Machinery Works
CS - Up to 50mm thickness Furui De-Ethanizer Tower Sewon E & T Corp Flare Knockout Drum – HP Sung Jin Geotec Co. Ltd Flare Knockout Drum- LP Sung Jin Geotec Co. Ltd Fuel Gas scrubber Sung Jin Geotec Co. Ltd Fuel Gas Scrubber – LP Sung Jin Geotec Co. Ltd General Baipini Engineering Pty Ltd (Sydney)
Fusion Weld Hudson-HEI (Perth) L & A Pressure Welding Stelform
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 17 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Heating Medium Expansion Drum Sung Jin Geotec Co. Ltd HPC Dis. Scrubber Sung Jin Geotec Co. Ltd HPC Suction Scrubber Sung Jin Geotec Co. Ltd Instrument Air Receiver Sung Jin Geotec Co. Ltd IP Comp Suct Scrubber Sung Jin Geotec Co. Ltd IP Discharge Scrubber Sung Jin Geotec Co. Ltd IP Separator Sung Jin Geotec Co. Ltd Large Diameter / Heavy Wall
Pressure Vessel Sung Jin Geotec Co. Ltd
Medium Wall Vessels Petrozavodskmash Corp Medium/Heavy Vessels Larsen and Tourbro Ltd Methanol Storage Tank Sung Jin Geotec Co. Ltd NFPA 22 Firewater Tanks Bachmans
Saunders International P/L Nitrogen Receiver Sung Jin Geotec Co. Ltd SS - Up to 50mm thickness Furui SS - Up to 50mm thickness, limited
to 1200mm in diameter Nanjing Chemical Machinery Works
SS & Special Alloy Shanghai Morimatsu Stainless Steel Vessel / Column -
Over 50 ton Doosan Mecatec Hudson Industries Daekyung Machine and Engineering Company Ltd En-Fab Inc Doosan Mecatec
Unfired (Class II and Class III) Amalgamated Metal Builders (M) Sdn Bhd Unfired MSET Engineering Corporation Sdn Bhd
Petra Fabricators Jutasama AMC
Utility Vessel Packages Biapini Engineering Pty Ltd Separators Cyrogenic Deethanizer Tower IL Sung Engineering & Construction Co Ltd Filter - Small Diameter Burgess Manning
Kobe Steel Ltd KNM Process Systems Sdn Bhd Pall Filters Peerless Peco
Natco Process Hazardous Open Drain Separator
Tank Natco Process
HP Sung Jin Geotec Co. Ltd LP Sung Jin Geotec Co. Ltd Oily Water Burgess Manning Small Diameter AWC Inc Test Separator Sung Jin Geotec Co. Ltd Hudson Industries
Natco Canada Ltd Volgogradneftemash
7. Heat Exchangers
Category Description Manufacturer
Chart Heat Exchangers c/o SME Aerial Cooler Vibo Valencia Air Cooled Hudson-HEI (Perth)
Jord Engineers
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 18 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Pleny Uniquip GEA-BTT Dynac Sdn Bhd
3XX SS GEA-BTT CS/LTCS GEA-BTT Air Cooler A.P.V. Spiro Gills
FBM-Hudson Italiana Spa GEA Air Exchangers, Ltd. Heat Exchangers International Hudson Products Korea Heat Exchanger Mitsui Shipbuilding & Engineering Nuovo Pignone, S.P.A. Olmi, S.P.A. Hamon D'Hondt SA Bronswerk Foster Wheeler Ltd Hammco Heat Exchanger of Australia Hudson-HEI
Brazed Aluminum (Cold Boxes)
Chart Industries Linde AG Kobe Steel Ltd Sumitomo Precision Products Chart Industries
Hairpin and Double Pipe Brown Fintube France Alco Products
Hudson-HEI RW Holland Inc
Plate & Frame Hisaka Works Ltd Alfa Laval Swep Tranter Tranter
Printed Circuit (PCHE) Heatric Shell and Tube Amalgamated Metal Builders (M) Sdn Bhd 3.5% Ni Hantech Ltd Carbon Steel
Baipini Engineering Pty Ltd (Sydney) Hudson-HEI Daekyung Machine and Engineering Company Ltd
Carbon Steel >600 psi Energy Exchanger Company Graham Manufacturing Ltd Heat Exchangers International Hitachii Zosen Mechanical Corp Japan Steel Kobe Steel Ltd Bagnolo
Carbon Steel <600 psi Energy Exchanger Company Fabsco FBM-Hudson Italiana Spa Fusion Weld Graham Manufacturing Ltd H Leffer Hitachii Zosen Mechanical Corp Japan Steel Leffer Ohmstede (Exell, Inc.) Olmi, S.P.A. Bosco Bagnolo
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 19 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Metropolitan Engineering & Fabrication Proser Plenty Uniquip Belleli Bronswerk Constructions Metalliques Leffer Heat Exchanger of Australia
Carbon Steel / Alloy >600 psi Leffer Mitsui Shipbuilding & Engineering Nuovo Pignone, S.P.A.
Carbon Steel Vessel / Column SS Sewon E & T Corp SS Shanghai Morimatsu Stainless Steel
Daekyung Machine and Engineering Company Ltd I.H.I. Jord Engineers L&A Pressure Welding Stelform
8. Mechanical Valves
Category Description Manufacturer
Acceptable Manufacturing
Facility (City/Country)
Ball 1/4" to 2" 1000psi to 15000psi
Ferritic Alloys and SS
Oliver Valves Ltd UK
1/4" to 1-1/2" 1000psi to 6000psi
DSS and SS Tyco Richards Alfa Valvole
Australia Italy
Actuated Crane Canada Inc Canada Floating Ball < 6" Cooper Cameron
Neles-Jamesbury PBV Valvitalia Velan Inc ABV Srl (Italy) KVC UK KITZ TYCO RICHARDS OMB GROVE ITALIA RBR VALVOLE ALFA VALVOLE
USA, Finland Stafford TX, USA Italy Global Italy JAPAN AUSTRALIA ITALY ITALY ITALY ITALY
Cryogenic OMB Kitz (Japan) Pibiviesse Pibiviesse SPA.
Italy Japan Italy Italy
Floating Ball <2" Grove - Italia SRL Italy Metal Seat Fire Safe Carbon / Low
Chrome / SS Neles-Jamesbury Orbit GROVE ITALIA RBR VALVOLE MIR VALVES ORSENIGO (FLUITEK)
USA, Finland USA
Resilient Seated Fire Safe Carbon / Low Chrome / SS
Cooper Cameron Neles-Jamesbury
Global USA, Finland
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 20 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Orbit WKM
USA USA
Subsea Ball Valves Cooper Cameron PetrolValves
Global Italy
Trunnioin Mounted
>2"
Cryogenic Pibiviesse Kitz (Japan) Perar Poyam Valves
Italy Japan Italy Spain
Trunnion Mounted >2"
ABV Srl (Italy) Cooper Cameron Grove - Italia SRL Pibiviesse Valvitalia Velan
Italy Global Italy Italy Italy Global
Trunnion Mounted >2" Argus Borsig CORT Hindle Cockburns M&D TK KVC (UK) Crane Australia Tyco Richards PCC KTM RBR VALVOLE ORSENIGO (FLUITEK) BREDA ENERGIA RING-O VALVE DELLA FOGLIA MIR VALVES
Germany Germany UK Australia Australia Italy Japan ITALY ITALY ITALY ITALY ITALY MALAYSIA
Bronze, Nickel Aluminum Bronze
Seawater Service
CRANE SHIPHAM
UK UK
Butterfly Xomox Corp. Adams Armaturen Houston TX USA,
Germany API 609 >2" Cooper Cameron
Neles-Jamesbury Demco
Global USA & Finland Global
API 612 >2" Flowseal Germany Metal Seat Fire Safe High
Performance, API 609 – Category B, Carbon, Alloy, SS
Posi-Seal (Fisher-Emerson) Vanessa
Italy
On-Off Metso Field Systems OY Tyco Valves & Control Distribution
Resilient Seated Fire Safe High Performance, API 609 – Category B, Carbon, Alloy, SS
Flowseal Keystone International Neles-Jamesbury McCanna Posi-Seal Winn
Germany Italy USA & Finland
Rubber Liner and / or Seat
Air and water
Class 150 & Lower, Water
Keystone International Flowseal
USA
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 21 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
service & water Lug Types, API 609 – Category A, Iron & Carbon Steel
Triple Eccentric
Cryogenic Orton Vanessa Adams-Armaturen
Italy Italy Houston TX USA, Germany
Bronze, Nickel Aluminum Bronze
Seawater Service
CRANE SHIPHAM
UK UK
Check 1/4" to 1" 1000psi to
6000 psi SS
Oliver Valves Ltd UK
Cast CS & Cast L.T.C.S.
150# & 300# Goodwin International Ltd UK
Cast SS Cryogenic Goodwin International Ltd UK Large bore, swing
check Kitz Japan
Pacific Powell Walworth Wheatley Grinnell Entech Velan Malbranque
Non Slam Goodwin International Ltd Crane Canada Inc Mokveld Valves Bv. Daniel Stockham
UK Canada Netherlands USA Australia
Special Check Valves
Goodwin International Ltd UK
Wafer >2" Crane Canada Inc Duo-Check Crane
Canada Conroe TX, USA
Wafer & Wafer Lug Goodwin International Ltd Crane Australia
UK Australia
Water Service IBBM, All Iron, Bronze
Proquip Dual Plate
Velan Kitz Tom Wheatley
Global Japan USA
Gate 1/2" to 1" 1000 psi to 15000 psi
Ferritic Alloys and SS
Oliver Valves Ltd UK
Gate >2" Jenkins
Gate / Globe / Check
Poyam Valves Cooper Cameron Valves Raimondi
Spain Global USA, Canada
>2" Bel Valves OMB Crane Pacific Powell Walworth Velan Malbranque Grinnell WKM
UK Italy
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 22 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
API 600 Carbon Steel - Flanged & Butt welded
Tong Yung (TY) Korea
API 602 All materials
Bonney Forge DSI SWI Valve Vogt Pacific Smith Valves Stockham Crane
USA, Italy Italy S Korea USA
OMB API 603 & ASME
B18.34 SS & Alloy – incl. Low Chrome
Pacific Tong Yung (TY) Velan Inc
Long Beach, USA Korea Global
Bronze Valves Kitz USA Cast Carbon Steel Class 600
and above Pacific Long Beach, USA
Cast CS & Cast L.T.C.S.
Class 150# and 300#
PK Valves Korea
Class 600# and Above
Velan Inc Global
Forged < 2" Tong Yung (TY)
<1.5" Saccap Service Smith Valves
France Houston TX USA
Water Service IBBM, All Iron, Bronze
Kitz Milwaukee
USA
Air & Water Service Brass & Bronze
Kennedy Milwaukee Valve Stockham
Elmera, NY USA Milwaukee, WI USA Cullman USA
< 2" Cryogenic OMB > 2" Cryogenic Tong Yung (TY) Korea Manifold ACECO
FMC Texsteam
USA USA
Needle 1/4" to 1" 1000psi to 15000 psi
Ferritic Alloys and SS
Oliver Valves Ltd Anderson Greenwood Astava Kenmac Marsh Precision General Whitey
UK
Special Axial Flow Check Valves
Mokveld Valves Bv.
9. Process Piping
Category Manufacturer Acceptable Manufacturing Facility
(City/Country)
Alloy 20 and other Nickels Mitsubishi Materials Japan
LOW CHROME UP TO 13% Kawasaki Koppel Steel
Japan Usa
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 23 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Mannesmann Sumitomo Tubacex Vallourec
Germany Japan Spain France
Bends for SCR & Flowlines Dalmine Italy Carbon Steel Dalmine Italy Carbon Steel Seamless - Impact Tested
Dalmine S.P.A. Italy
Carbon Steel Seamless - Impact Tested -- EFW
D'Amore & Lundardi S.P.A.
Carbon Steel - Seamless
Koppel Steel North Star Sharon Tube Tubacex U.S. Steel Vallourec Nippon Steel Corp. V & M Do Brasil Sa
Usa Usa Usa Spain Usa France Japan Brasil
Carbon Steel – Seamless and Welded
Sumitomo Metal Industries, Ltd. Japan, Europe
Carbon Steel Welded - ERW
Newport Steel Usa
Carbon Steel
Benteler Berg Steel Pipe Corp. Confab CSI Tubular Products EEW Hyundai Ilva S.P.A. JFE Kawasaki Mannesmann Maverick NKK Siderca Sumikin Bussan Corp Tex-Tube Company Thyssenkrupp Mannex Gmbh Sif Group Bv Kurvers Inc
Germany USA USA USA Germany, Korea Korea Japan Japan Germany USA Japan Argentina Japan Houston TX, USA Germany USA
Carbon Steel, SS, Alloys Seamless
V & M Tubes Europe, Usa
Coating Europipe Gmbh Germany Coating External - Weight
Compression Coat Inc. Usa
Copper Nichel Vdm Austrailia Copper Nichel Norman W Hutchison Fittings Seamless, Welded
Sk Bend Korea
Flexible Pipe Technip - Coflexip France Flexible Pipe Wellstream UK
FRP Piping Components Ameron Pte Ltd FIBERBOND
USA, MALAYSIA
HDPE Pipe, Fittings, Flanges Great Western Supply Co
Induction Bends
Fabricom Bassi Luigi Bendtec Dai Ichi High Frequency Co. Ltd.
Belgium Italy USA Japan
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 24 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Germany USA
Mannesmann Pacific Pipe Company Simas Shaw Sunland
Insulation - Line Blankets Bd Profiles Ltd Pipe Fabrication - Pipe A672 / API
Eew Germany, Korea
Pipe Spool Fab and Induction Bends
Sung Il Co., Ltd. (Sim) Korea
Stainless Steel Kobe Steel Ltd Nippon Steel Corp. Kurvers Inc
Japan Japan Usa
ALLOY, SS, MONEL AND ETC.
Al Tech Avesta Curtis Wright Haynes Inco Alloy Kawasaki Mannesmann Sandvik Schoeller Bleckman Sumitomo Swepco Tad Usa Trent Tube Tubacex
Usa Usa Usa Usa Usa Japan Germany Usa/Sweden/Canada Austria Japan Usa Usa Usa Spain
Stainless Steel & Incoloy 825 Officine Orsi Spa Prochem Pipeline Products Onesteel Piping Systems
Italy Austrailia Austrailia
10. Process Equipments
Category Description Manufacturer Acceptable Manufacturing
Facility (City/Country)
Bolts Bolts for SPO Flange 100%
Compact Flange Canada
High Tensile Bolts Hobson Engineering Australia Southern Bolts & Nuts Sdn Bhd
J. Blackwood & Son Lone Star
Australia Houston, TX USA
Hight Tensile Studbolts & Nuts
Lamons Gasket & Bolt Company TX, USA
Studded Bolts & Nuts Hwashin Bolt Korea Barrel Closures Bandlock 2 Coated Bolts & Nuts
American International Industries
Closures
Gd Closures Grayloc Lts Inc Re-Flange
USA USA UK
Dampers Wahlco Metroflex, Inc USA Expansion Joints Metal Unaflex USA
Metallic
Bachmann Industries Badger Expansion Joint Systems Flexonics, Inc.
USA USA USA USA
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 25 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Hy-Span Microflex Inc
USA USA
Non Metallic
Proco Products Bachmann Industries Expansion Joint Systems Garlock General Rubber Goodall Rubber Wahlco Metroflex, Inc Jord Pathway Bellows
USA USA USA USA USA Canada USA Australia
Fittings
Nippon Steel Corp. Sam Yang Metal Prochem Pipeline Products Onesteel Piping Systems
Japan Korea Australia Australia
Barred Tees Kurvers France Sarl Bassi Luigi Moffat 2000 Ltd
France Italy UK
Branch Outlet Fittings (O'lets)
Anvil / Canvil Fuji High Pressure Iml Mega Penn Machine Tk Corporation Westbrook Wfi International Bkl Bonney Forge
USA, Canada Japan Italy Italy USA Korea Houston, TX USA Houston, TX USA UK Italy, USA
Branch Outlet Fittings (O'lets)-CS only
Phoenix Forgings USA
Buttweld End Fittings
Genoyer Group Inc Tk Corporation Integris Metals Bonney Forge Fuji High Pressure Taylor Forge Technoforge, S.P.A. Ladish Mill Iron Works
USA Korea Canada Italy, USA Japan USA Italy USA USA
Buttweld End Fittings
Benkan Custom Alloy Dynamic Products Flo-Bends Inc Interfit Mannesmann Ram Forge & Steel Sumitomo Metal Industries, Ltd. TK Corporation Tube Turns WFI International Integris Metals Penn Machine BKL
Japan USA Houston, TX USA USA France Germany USA Japan Korea USA Houston, TX USA Canada USA UK
Shaw Alloy Piping Products
Buttweld End Fittings-Carbon Steel
App Erne Tubeline Wilhelm Gelbach Coveco
USA AUSTRIA USA GERMANY VENEZUELA
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 26 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Hackney (Ells Dated 4/91 Or Later) USA Tube Forging Of America (Logo: Tfa) USA
Vallourec/Interfit (Elbows And Reducers Only)
FRANCE
Chero Piping Canadoil Forge Ltd Anggerik Laksana Sdn Bhd (Elbows up to 24” , Reducers up to 36”, Tees and Caps)
Buttweld End Fittings-Low Chrome (up to 13% Chrome)
App Erne Petrol Raccord Wihelm Gelbach Coveco
USA AUSTRIA ITALY GERMANY VENEZUELA
Wilhelm Schulz (Ell Dated 6/92 Or Later)
GERMANY
Canadoil Forge Ltd
Buttweld End Fittings-Alloy
App Erne J&J (Reducers Only) Petrol Raccord
USA AUSTRIA USA ITALY
Wilhelm Schulz (Ell Dated 6/92 Or Later)
GERMANY
Buttweld End Fittings-Stainless Steel
App Erne Flowline Petrol Raccord Coveco
USA AUSTRIA USA ITALY VENEZUELA
Wilhelm Schulz (Ells Dated 6/92) GERMANY
Supaflo Sse Sterling Tubes Galperti Canadoil Forge Ltd Anggerik Laksana Sdn Bhd (Elbows up to 24” , Reducers up to 36”, Tees and Caps)
Copper Nickel Vdm Norman W Hutchison
Australia
Forged Steel Fittings
Alloy Stainless Products Ladish Mega Anvil / Canvil Bonney Forge Camco (Capitol Mfg) Delcorte Fuji High Pressure Iml Taylor Forge Technoforge, S.P.A. Tube Turns Westbrook
USA USA Italy USA, Canada Italy, USA USA France Japan Italy USA Italy USA Houston, TX USA
Forged Steel Fittings-ANSI B16.11
Standard Fittings (Cs Only) Vogt
USA USA
Forged Steel Unions Wfi International Houston, TX USA Incolog 825 Officine Orsi Spa Italy
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 27 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Pipe Nipples-Straight - All Materials
Beck Gallagher Grinnel (Except Galvanized) J.B. Smith Missouri Pipe Fittings (Mpf) Merit Brass
USA USA USA USA USA USA
Swage Nipples - All Materials
J.B. Smith W.C. Norris
USA USA
Low Temp. Pipe Fittings (A333)
Techtubi Ibf Galperti
Flange Isolation/ Insulating Kits
Pikotek USA/Canada
Flanges Compact Flanges Lts Inc Vector International
USA Norway
Duplex Integris Metals Canada Flange Isolation Kits
Pipeline Seal & Insulator Houston TX, USA
Flanges
Boltex Buffalo Flange Flo-Bends Inc Forgerossi Kofco Ladish Melesi Metalfar National Flange Piping Products Shimoda Iron Works Sumitomo Metal Industries, Ltd. Tube Turns WFI International
Houston TX, USA USA Italy S. Korea USA Italy Italy Houston TX, USA Houston TX, USA Japan Japan USA Houston, TX USA
CS
Burton Delingpole Coffer Conforja Daniel Forjas De Santa Clara (Logo: Puma) Hackney Kerkau
UK USA BRAZIL USA VENEZUELA USA USA
Hanger Galperti Houston, TX USA, Italy
Low Temperature Machinefabriek-Heerbaart Bv Albert Grefenberg Gmbh + Ko Kg
Orifice Flange Euromisure Srl Italy Protector Hydratight Italy
Stainless Steel And Other Alloys
Bebitz Flowline Gerlin/Tube-Line Stainless Ideal Maas Texas Metals Western Forge
GERMANY USA USA USA USA USA TEXAS
SS, CS and Other Alloys Wildhelm Geldbach Ulma/Enara
GERMANY SPAIN
Stainless Steel Integris Metals Canada Flanges & Connectors
Welding Units UK
Flanges & Fittings Carbon & SS Van Leeuwen Pipe And Tube Europe Kurvers Rolled Alloys International Ltd
Netherlands France, Houston TX USA UK
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 28 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Techdrill UK
Gaskets
Tekno Logam Sdn Bhd Alfa-Meli Precision Industries Sdn Bhd Novus Sealing (M) Sdn Bhd
For Heat Exchangers Garlock Sealing Technologies Specialised Gaskets Pty. Ltd. (Flexitalic Licensee)
Australia
Ring Joint
Flexitallic Klinger Kukil Inntot Samsung Industry
UK S Korea S Korea
Spiral Wound Flexible Graphite filled
Econosto Singapore Pte Ltd Flexitallic Furon/Garlock Hofland Deltaflex Lamons Gasket & Bolt Company Klinger Kukil Inntot Metaflex Samsung Industry Cartec Sealing Tech
UK S. Korea UK S. Korea S. Korea
Hose and Hose Fittings
Grayco Washdown Assys Tyco Flexible Piping Systems
Australia Australia
Hub Clamp Connectors
Galperti Grayloc
Houston, TX USA, Italy
Induction Bends High Frequency Bending Sung Il Co., Ltd. (Sim) S Korea
Isolation/ Insulating Joints
Oil States Industries, Inc. Tube Turns Zunt Italiana S.R.L
USA USA Italy
Lifting Equipment & Rope
A Noble & Son Australia
Miscellaneous HDPE Liner Gse Lining Technology Gmbh Germany Swivel Components Marberry Machine Non Metallic, Fiberglass
Pipe / fittings Ameron
O-Ring International Seal Co. Parker Hannifier (Australia) Pty Ltd
Austrialia USA
Pipe Couplings Dresser Flow Control Stafford TX, USA
Pipe Hangers & Supports
Constant Spring Cams, variable Spring Cams, Clamps, Shoes & Guides
Aaa Technology Binder Group Pty Ltd Rilco Manufacturing Inc
Pipe Supports Pipe Hangers and Clamps Onesteel Piping Systems J. Blackwood & Son
Australia Australia
Pipeline Support, Stabilization and Protection
Submar
Swivel Joint Fluid Swivels Fmc Sofeco Floating Systems
Italy Traps Liquid Traps
Douglas Italia Spirax Sarco
Steam Traps Tlv Co Ltd Valve & Pump Packing
Mid Valley Bearing*
Welding Electrodes Bohler Electrodes & Wire Esab Weld Wire Redaeill Italy Weld wire and Electrodes Lincoln Electric USA Stick Welding Electrodes Kunci Quantum Sdn Bhd
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 29 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
11. Fire Protection
Category Description Manufacturer
CO2 System Carbon Dioxide Ansul Inc Kidde
Deluge valves Deluge Cla-Val Viking
Deluge valves Knowsley SK Fire and Gas Detection Fire and Gas Detection System Mircom Flame and Fire Detector Fenwal
POGC Fire Extinguisher Portable - Carbon Dioxide (5 kg) : Model # OU-8 Pozhtechnika Portable - Potassium Bicarbonate (9 kg)
Stored Pressure : Model # OP-10 Pozhtechnika
Portable
Ansul Inc Cosalt Chubb Fire Safety
Wheeled Ansul Fire Fighting Equipment Chubb Fire Safety
Knowsley SK Foam Skid
National Foam Quell Fire Safety
Fire Fighting Vehicle Hook-up Knowsley SK Fire Hose Angus
Chubb Fire Safety Knowsley SK Manuli National Fire Hose Potter-Roemer
Fire Hose & Nozzle Cabinet Knowsley SK Fire Nozzle Knowsley SK Fire Proofing Intumescent Coatings - Product: Thermo-lag Carboline Intumescent Coatings Chartek Intumescent Coatings - Product: Firetex Leigh's Paints Intumescent Coatings PittChar Fire Proofing Board and Metal Jacketing
Pittsburgh Corning FoamGlas Insulation
Firemans's Equipment GuardFire Ltd Knowsley Sk
Flame Arrestors Varec Gasous Fire Fighting System Topside
NK Co Ltd
GRE / FRP Pipe and Fittings Bondstrand Conley Corp Smith Fiberglass FIBERBOND
Hose Reel Chubb Fire Safety GuardFire Ltd
Hydrant Pillar Type Knowsley SK Mobile Fire Extinguisher Carbon Dioxide Knowsley SK Dry Chemical Knowsley SK Monitors Akron
Angus Elkhart
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 30 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Stang
Manual Foam Knowsley SK Oscillating Foam Knowsley SK Nozzle Akron
Angus Elkhart Stang
Portable Fire Extinguisher Carbon Dioxide Knowsley SK Dry Chemical - Stored Pressure and Cartridge
Operated (not specified in the documents which one was supplied)
Knowsley SK
Foam Knowsley SK Water Knowsley SK Skid Dry Chemical American Fire
Angus Ansul Inc Kidde
Foam Chubb Fire Safety Knowsley SK
Foam - Deluge Knowsley SK Fire Protection Engineering
Sprinkler Knowsley SK Twin Agents Skids American Fire
Ansul Inc Water Knowsley SK Water spray sprinkler systems Angus Watermist System Marioff
12. Life Safety
Category Description Manufacturer
Accoustic Enclosures G&S Machining Stalfab Union Hydraulics
Air Pack Breathing Apparatus Model # 80411501 Scott Breathing System Delmo
SMC Eye Wash Station BOC Safety
Self-contained, gravity-fed : Model # 01104070
Encon
Fast Rescue Boat Alexander / Ryan Marine & Safety Co Norsafe AS Willard Marine
Fast Rescue Craft Davit Allied Marine Crane Fire Blanket Kit Model # SAF1000W Junkin Fire Stand Closed type
Includes: crowbar, spade, shovel, hook with wooden handle, pail, and wire rope cutting kit.
Pozhtechnika
First Aid Kit Includes bandages, medicinal, burn treatment, and eye treatment Model # 012101-2959
North
Life Float Billy Pugh Cosalt
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 31 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Hy-Grapha Jim Buoy Survival Systems International Viking Lifesaving Equipment Pte Ltd
Life Jackets Billy Pugh Cosalt
Hy-Grapha Safeguard Stearns Taylortec Viking Lifesaving Equipment Pte Ltd
Life Raft Inflatable Cosalt Viking Lifesaving Equipment Pte Ltd First Marine Service Sdn Bhd
Medical European Dental Center AEA International (Sakhalin) ZAO European Medical Center
Personal Protective Equipment DRC Sakhalin Group LLC ZAO Sakhalin Vostok Service
Ring Buoy Billy Pugh Cosalt
Hy-Grapha Jim Buoy Viking Lifesaving Equipment Pte Ltd
Safety Equipment Anchor Marine Transportation Ltd Seaward Safety Inc Unitor Ship Service (S) Pte Ltd Viking LifeSaving Equipment Bergen AS
Protective Clothing Can't Tear Em Global Safety Solutions & Mgt
Stair Treads J Blackwood & Son Safety Shower Hughes Safety Shower
International Medical Clinic K&D Pratt Ltd Keegan Speciality Enterprise Inc QMC (Quality Marketing Company) Silver Ships Inc Survival Systems International
Safety Shower & Eyewash Station
Model # 8710 Haws
Self-Contained Breathing Apparatus (SCBA)
Scott
Stretcher Basket type Model # 71 (stretcher), & 559 (brackets)
Ferno
Survival Craft Norsafe AS Survival Systems International
Survival Craft Assys and Components
Ropes and Winches Brucker Survival Systems Int.
Work Vests Billy Pugh Cosalt Hy-Grapha Steams Viking Lifesaving Equipment Pte Ltd
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 32 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
13. Flare System
Category Description Manufacturer
Flame Front Generator John Zink Company, LLC
Flare Systems Callidus
Flare Industries Inc
GBA Corona Inc
Hitachii Zosen Mechanical Corp
John Zink Company, LLC
Sam Shin Ind
Zeeco Inc Flare Systems Industrial Metallurgical Van Dam Flare Tip Package Callidus
Environmental Group P/L Motherwell Bridge John Zink Company, LLC John Zink Asia Pacific Kaldair Ltd NAO Roxar Victory International SA Zeeco Inc Mactronic
LP Flare Tip John Zink Company, LLC LP Tip Blower / Motor John Zink Company, LLC Miscellaneous Vent Tip & Snuffer Package GBA Corona Inc
14. I&C
Category Description Manufacturer Remarks
Analyzers Automatic Sample System
SGS Redwood
BS&W Analyzer AGAR Endress & Hauser Faure Herman Invalco
Chromatographs Daniel Industries Rosemount Analytical
ABB Honeywell Ltd.
Corrosion Monitors
ClampOn AS CorrOcean Srl Fluenta AS Rohrback Cosasco Systems
Density Analyzer Micromotion Schlumberger Industries Solartron
ESD Analyzer Honeywell Ltd. F & G Detection Fire Detection Det-Tronics
Fire Eye Inc General Monitors Micropack Detection
Optical
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 33 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
(Americas) Inc Kidde Fenwal
Honeywell Ltd. Pyrotronics (Siemens) Thermal & Smoke Sensors F & G Detection Gas Detection Det-Tronics
Gastech General Monitors Seiger Bacharach Simrad Optronics Draeger
Gas Detectors & Controllers
Gas Tech MSA (Mine Safety Appliance) Riken Keiki GX-7 Sieger
Gas Detectors (portable)
H2S in HC Analyzer
ABB Fluid System
Berthold Australia Rty Ltd Det-Tronics Foxboro General Monitors MSA Siegar Monitor Corporation Zellweger Analytics
Moisture Analyzer Ametek Instruments Dupont Endress & Hauser General Eastern Gruter & Marchand / Shaw Panametrics Inc PCI Div Rosemount Analytical
Oil-in-Water Analyzer
AGAR Bran+Luebbe, Inc Invalco Micromotion Segrist Segrist Teledyne Analytical Turner Design (Hydrocarbon Business Group) Western Research (Ametek) Hydril Haliburton Roxar MFI
Oxygen Analyzer Ametek Instruments Orbisphere Panametrics Inc PCI Div Rosemount Analytical Servomax Teledyne Analytical
Yokogawa
PH Meter & Conductivity Analyzer
Endress & Hauser Zellweger Analytics
Yokogawa
Sand Detector Analyzer
CorrOcean Srl Fluenta AS
Topside Particle ClampOn AS
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 34 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Monitor System
Water Cut Analyzer
Hydril
Water-in Oil Analyzer
AGAR Hach Loveland Halliburton Moriba Phase Dynamics Sigrist Wedgewood Delta C Technologies Inc
Flow Flow Metering Coriolis Micro Motion Inc. Flow Computers Daniel Industries OMNI
Spectra - Tek Solartron
Yokogawa Magnetic
Flowmeters Brooks Instruments Krohne Rosemount Foxboro
Honeywell Inc. Yokogawa
Multiphase Flowmeter
MPM (Multi Phase Meters) Schlumberger Industries Roxar ASA
Positive Displacement meters
American Meter Barton Instruments Brooks Instruments Faure Herman Smith
Turbine Meters Brooks Instruments NuFlo Smith Meter, Inc. Halliburton ITT Barton Faure Herman
Daniel Industries
Ultrasonic Flowmeter
Caldon Daniel Industries Fluenta AS Instromet Krohne Sick Mahaik
Siemens V cones McCrometer Variable Area
Meter ABB
Brooks Instruments Penberthy Rosemount Wallace & Tiernan
Vortex Flowmeters
ABB Honeywell Inc. Yokogawa
Endress & Hauser Foxboro Rosemount
Wetgas Meter MPM (Multi Phase Meters)
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 35 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Coriolis Meter Endress & Hauser Rheonik
Turbine Meters Faure Herman Ultrasonic
Flowmeter Panametrics
Flow Flow Regulator Atlantic Group Teknomax Yarway
Flow Switch Barton Instruments Fluid Components Intl (FCI) KDG Moberey Ball Delta Control/Pro-Quip Delavel/Barksdale Magnetrol
Flow Transmitters DP ABB Honeywell Inc. Yokogawa
Endress & Hauser Fisher Foxboro Rosemont
Flow Tubes, Venturies and Flow Nozzles
Daniel Industries
Leak Detection Equipment
ATMOS
Orifice Plates Fittings Berger Daniel Industries DAR En-Fab Inc Fluidic Techniques Oil and Gas Specialties Peco / Smith Meter Inc. Red Man Pipe and Supply SPM Triad Measurement ISA Controls
Meter Runs
Emerson Process Management
Pitot Tubes Averaging Pitot Tubes
Airflow Fisher KDG Moberey Mid-West Instrument
Sight Flow Brooks Instruments Daniel Industries Jacoby-Tarbox Jerguson Brookds Inst Div Magnetrol/AWC Penberthy Wallace & Tiernan W E Anderson/Wesco
Thermal Mass Electronics
Fluid Components Intl (FCI)
Pitot Tubes Averaging Pitot Tubes
Emerson Process Management
Orifice Plates Fittings Daniel Industries Meter Runs
Pitot Tubes Averaging Pitot Tubes
Dieterich Standard Inc
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 36 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Instrument Automation
DCS ABB Inc Honeywell Inc. Siemens Yokogawa
British Aerospace Foxboro MICC Emerson Process Fisher-Rosemount Division
Electronic Safety Shutdown
ABB Inc Honeywell Inc.
August Systems Hima ICS Triplex Moore Industries Inc. Triconex
PLC Allen Bradley Modicon
GE Siemens
SCADA Fisher Level Glass Level Gauge Jurgenson
Klinger Krohne K-Tek Nihon Klingage Penberthy TCVAL Penberthy Daniel
Level Gauge Magnetic Babbit International Jerguson K-Tek Magnetrol International Magnetrol International France MagTech Penberthy Tundra Controls Ltd
Radar Khrone Magnetrol International Ohmart / Vega Corp Rosemount Saab
Level Switch Float / Displacer Bestobell Fisher KDG Moberey Magnetrol International Masoneilan Division Static-O-Ring (SOR) Tokyo Keiso Co Ltd
Electric
Float / Displacer Fisher Pneumatic
Capacitance AGAR Magnetrol International
Level Switch Endress & Hauser Fisher Rosemount Magne-Sonics Magnetrol International Sensall Static-O-Ring (SOR)
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 37 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Level Transmitter Capacitance Drexelbrook Endress & Hauser Vega
DP Endress & Hauser Fisher Foxboro Magnetrol International Major Controls Rosemont Rosemont
Yokogawa Honeywell Inc. ABB
RF Probe Babbit International Krohne Magnetrol International
Sonic Kay-Ray Krohne Sensall
Nucleonic Berthold Austrailia Rty Ltd Nuclear Scanning Services
Float / Displacer Fisher Static-O-Ring (MSW) K-Tek ISA Controls Masoneilan
Pneumatic
Miscellaneous Alarm Systems Alarm Trips - Current Voltage
Dixon Moore Industries Inc.
Annunciator Panels
Bintek Ronan Engineering Zantek
Annunciators Riley - Panalarm Best Panalarm Ronan
Field Mounted Receivers
Indicator Dixon Dresser Instruments Division Foxboro
Electric Pneumatic Pneumatic
Pneumatic Controller
Fisher Non-Indicating
Fisher Foxboro Foxboro France SA Masoneilan
Indicating
Pneumatic Control Components
Axelson BWB Cal Con Versa
Recorder Barton Instruments Foxboro
Mechanical
Flame Arrestors Alsatec Groth Protectoseal Varec
Hand Switches Allen Bradley Schneider Electric - Square D
Hydraulic Power Unit
Basic Technologies Cooper Cameron Dynex / Rivett Inc
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 38 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Hydrostatic transducers
Ian Conrad Bergan Inc. Kongsberg-Autronica A/S Scana Electronics c/o AUM
Intrinsic Safety Barriers
Elcon Instruments MTL
Electronic ICS Triplex
Misc. Local Instrument Panels Surge/Capacity Compressor Controls Corp.
(CCC)
Automation USA Baker Brisco Engineering Fluides Service Hydrolex, Automated Controls Test Inc Texas Systems and Controls Inc TSI, Inc. W Industries RAN Puffer Sweiven Petrotech
Pig Signal ClampOn AS Fluenta AS Kidd Kidd Pipeline & Specialties Maloney Peco / Smith Meter Inc. T.D. Williamson, Inc.,
Meco Rupture Discs Anderson Greenwood /
Crosby Valve Fike Metal
BS&B
BS&B Safety Systems, Inc. Speed Switch Bentley Nevada
Tank vents Enardo Groth Protectoseal Shand & Jurs Varec
Terminal Blocks Phoenix Contact Weidmuller Klippon Entrelec
Tube Fittings Butech Turbo Mach
Enclosure Parker
Process Swagelok
Tubing Instrument Allegheny Ludium Alloy Metal & Tubes Autoclave Engineering Avesta Sheffield Carpenter Technology Sakai Sandvik Sumitomo Metal Industries, Ltd. TW Metals Thyssen
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 39 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Tubing Channel Channel Track J. C. White PW Industries
Vibration Monitoring
Amot Bentley Nevada Metrix Instrument Co. Robert shaw
Wellhead Control Panel
Automation USA Baker CAC Bumi Wangsa Sdn Bhd Mid South Controls and Services Petrotech Wormald Linott Oil and Gas Test Inc. Haven Automation
Frequency to Current Converter
Action Instrument Haliburton Moore Industries Inc.
Pressure Diaphragm Seal Dresser Instruments Division ITT
DP Indicators / Switches (Including Flow)
Custom Control Sensors Delta Controls Dresser Instruments Division Dwyer Instruments Inc. Fisher Geordin Mid-West Instrument NeoDyne Orange Research Inc Plenty Metrol Static-O-Ring (SOR)
Pressure Gauge Bourdori Rueger SA US Gauge WIKA Instruments
Pressure Manometer
Dwyer Instruments Inc. Meriam
Pressure Regulator
DP Cashco Endress & Hauser Fisher Masoneilan
Pnuematic Fisher
Process ABB Siemens
Fisher Masoneilan Taylor
Pressure Transmitters
Electronic (Direct & Diff)
ABB Yokogawa
Fisher Foxboro Rosemount Yamatake Custom Control Inc Static O Ring United Electric Honeywell Inc.
Transducers - P/I Rosemount
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 40 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Pressure Gauge Seintech / Wika DI Canada - Dresser Measurement Ashcroft Inc Ametek 3D Instruments Badotherm
Switch Electronic Custom Control Sensors Dresser Instruments Division ITT Barton NeoDyne Static-O-Ring (SOR)
Switch Pneumatic Fisher
Pressure Flowline Pilots Axelson BWB Controls Versa WKM
Temperature Temperature Assemblies
Berger Fisher Honeywell Inc.
Temperature Gauges
Dial Allesco Dresser Instruments Division Marsh Observator Rueger SA Tel-Tru US Gauge Ashcroft Inc
Temperature Gauges
Wika 3D Instruments Trend
Temperature RTDs DeGaussa (Sensycon) Rosemount Rueger SA Thermetrics Maverick Thermo Electric
Temperature Switches
Custom Control Sensors NeoDyne Static-O-Ring (SOR) Dresser Instruments Division United Electric Allen Bradley ASCO
Temperature Thermocouples
Rosemount
Temperature Transmitters
Electronic Rosemount Endress & Hauser Foxboro Rosemount Yamatake
Pneumatic Fisher Electronic ABB
Honeywell Inc. Yokogawa
Thermometers / Wells
Baro Controls Fisher Novatech Rawson and Co. Tel-Tru Transmark FCX Pty Ltd
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 41 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
WIKA Instruments
Bi-Metallic Thermometers
Dresser Instruments Division
Valve Safety Valve Farris Engineering
Actuated ESD Valve
Bel Valves Cooper Cameron Valves Grove Valve and Regulator Malbranque Neles-Jamesbury PetrolValve Argus Borsig TK KVC (UK) Tyco Richards PCC KTM RBR VALVOLE ORSENIGO (FLUITEK) BREDA ENERGIA RING-O VALVE DELLA FOGLIA MIR VALVES
Automatic Recirculation Valves
Atlantic Group Keystone Yarway Schroedahl-Arapp Gmbh
Choke Valve Cameron Willis CCI Valve Cooper Cameron Valves Cor-Val Halliburton Hydril Introl (ABB) Masoneilan Master Flo Master Flo Mokveld Valves Bv. Shaffer Varco Best Willis Vonk Teledyne Merla Thornhill Craver
Cameron Willis Ireland Ltd Control Valve Ball Fisher
Kent (ABB) Masoneilan Mokveld Valves Bv. Ring-O
Butterfly Fisher Masoneilan Neles-Jamesbury
Globe Fisher Masoneilan Mokveld Valves Bv.
Eccentric Disk / Low Noise
Fisher Masoneilan Mokveld Valves Bv.
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 42 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
PetrolValve Valtek
Motor Operated Dawler Raimondi WKM
Positioner Fisher Pnuematic Fisher
Masoneilan Valtek
Electropneumatic/Smart
Pressure Regulators
Fisher Cashco
Pump and Recirculation
Yarway
Shutdown Valves
Grove - Dresser Flow Control
Transducers (I/P)
Fisher Rosemont
Control Valve Dresser Flow Control Dresser Produits Industriels Fisher
Instrument / Tubing / Manifold
Anderson Greenwood / Crosby Valve Oliver Valves Ltd Parker Whitey
Injection Quill Oliver Valves Ltd
Limit Switch Fisher Westlock
Modulating Valves Fisher Pressure
Reducing Valve Daniel Industries
Fisher Grove Valve and Regulator Mokveld Valves Bv.
Pressure Relieving
Anderson Greenwood Brooks Instruments Daniel Industries Farris Engineering Mokveld Valves Bv.
Relief Conservation Vents
Anderson Greenwood Groth Varec
Pressure / Vacuum Vent
Anderson Greenwood Groth Shand & Jurs
Relief Safety Valve Anderson Greenwood Bailly-Birkett Crosby Tai Milano
Pilot Operated Relief Valves
Relief Safety Valve Axelson Brooks Instruments Daniel Industries Dresser Flow Control Mokveld Valves Bv. RSBD Sarasin Shand & Jurs
Bailey-Birkett Consolidated CCI
Spring Operated Relief Valves
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 43 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Crosby Farris Kunkle Tai Milano
Severe Service Valves
CCI Valve
Standard Control Valves
Dresser Produits Industriels
Solenoid Valve ASCO Versa IMF Honeywell - Skinner / Lucifer
Valve Actuator Axelson Baker Bernard Biffi Delta Controls EIM PetrolValve PALADON
Electric Limitorque Rotork
Hydraulic Flowserve/Valtek
Rotork Schafer (Emerson) Bettis Corporation Ledeen
Pneumatic (Piston)
Bettis Corporation Ledeen Rotork PALADON
Flowserve/Valtek
Pneumatic (Spring Return)
Bettis Prime Rotork Ledeen Limitorque Keystone Biffi PALADON
Valve Actuator Facilities
Dresser Flow Control Dupre Valves Puffer Sweiven Specialities Sunbelt Supply Valve Systems and Controls Wilson Valve Speciality Valser Engineering & Services Sdn Bhd
Isolation
Anderson Greenwood Astava Circle Seal Hoke Kenmac Marsh Nupro Precision General Whitey Oliver Blifold (Domino Series)
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 44 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
15. Telecom
Category Description Manufacturer
Tait
Access Control & CCTV Qatar Security Systems Aironet Antennas Antenna Cisco Antennas Microwave Andrew Corporation
Radiowaves RFS - Radio Frequency Systems
RF (& Accessories) Andrew Corporation Comrod PolyPhaser RFS - Radio Frequency Systems
VHF/UHF Jaybeam Cable Structured Cable System
(Voice & Data) ADC Krone
Antenna Cable Andrew Corporation UTP Belden RF Cablewave Fiber Optic Corning
Draka Alcatel-Lucent
Cable Fiber Optic, copper, panels, etc Siemon Closed Circuit Television System Production Monitoring Coex Ltd Production Monitoring, System / Exd
Cameras Hernis Scan Systems AS
Cameras Pelco Communication Console Motorola
Omnitronics Zetron
Communication Tower Alan Dick Allied Tower Andrew Corporation Eltel Networks (formerly TransMast) Rohn Tower Transmast
Converter B&B Electronics Entertainment System TVRO Applied Satellite Technology (Gardline
Group) Caprock Communications Sea Tel
Equipment Cabinets and Racks Chatsworth Rittal
Communications Console Omnitronics GMDSS - Global Maritime Distress and Safety System
Sailor
Liebert UPS Qatar Site & Power Meteorogical and Metocean System
Fugro
Data Acquisition Software Automasjon & Data AS NAVTEX Furuno Miros Wave Radar Miros A/S Offshore Muir Matheson Ltd Microwave Systems Alcatel-Lucent
Harris Stratex Harris / Farinon MDS (Microwave Data Systems)
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 45 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Motorola Sagem
UHF / Microwave Radios 4RF Communcations Network Equipment Wireless Ethernet Cisco Routers Cisco Switches Cisco Network Infrastructure Fiber Optic, copper, panels, etc ADC
CommScope General Cable Panduit Systimax Uniprise
Structured Cable System (Voice & Data)
Siemens
Offshore Loading System (Tanker) Telemetry
Bombardier Transportation
Outside Plant Manholes Pencell Polycom Video Conferencing Techno Q Public Address & General Alarm PA/GA Cable for Gaitronics only Amercable Speakers DNH A/S Federal Signal
Vodec Gai-Tronics Corp
Akusta Stentofon Le Las
Speaker/Beacons MEDC Fire Alarm Spector Lumenex Radar Systems Sperry Marine Collision Avoidance Furuno
Norcontrol Selesmar
Radio System UHF / Microwave Radios Alcatel-Lucent MDS (MicroWave Data Systems)
Aeronautical Icom Jotron
Marine (HF/VHF) Icom Operational (VHF/UHF) Motorola Trunked (VHF/UHF) Motorola Aeronautical - Base Station Park Air Radio Holland Pte Ltd Marine (HF/VHF) - Base Station Sailor Non-Directional Beacons Southern Avionics Satellite Handheld Phones Motorola
Thuraya Low Earth Orbit (LEO) Iridium Satellite Radio System Comm-Link Satellite Systems VSAT Caprock Communications
Schlumberger Stratos
Inmarsat B Nera Inmarsat C Sailor Inmarsat B, C, Fleet 55/77 Thrane Security Management Systems Gallagher Sensor Fence SOLAS/GMDS LIfeboat Radios Icom EPRIB's Jotron SARTS Jotron LIfeboat Radios Ratheon
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 46 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
GMDSS - Global Maritime Distress and Safety System
Sailor
Subsea Fiber Tyco System Integrator Nessco
Omega Integration Page Europa ABB Inc-Oil & Gas Process Automation Able Communications Kentz
TransTel Engineering Pte Ltd Satellite/RF Caprock Communications RF Radio Holland Pte Ltd Test Equipment RF Anritsu
Bird Electronics Fluke Harris Progressive Electronics
Video Conferencing Equipment Polycom WIMAX (IEEE 802.16d/e) Motorola Wireless WAN (extended Ethernet) Proxim
ABB Caprock Communications Hermes Datacomm
Nova Communications
16. Electrical
Category Description Manufacturer
Barriers Instrinsic Safety AWM Batteries and Chargers C & D Technologies DC Batteries C & D Technologies
Chloride Power GNB Saft Saft Singapore Pte Ltd. Yuasa Sonnenchein SEC Chloride C&D Technologies
DC Battery Chargers C&D Technologies Gutor Saft Fukuda Siemens Powertron / Powermatics LaMarche Solidstate Controls, Inc.
Battery Enclosure Container House International
Cable Marine shipboard cable AmerCable Balfour Beatty BIW Cable Furukawa Electric Prysmian LS-VINA Cable Rockbestos Suprenant Cable Corp
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 47 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Power and control cable AEI AWM Balfour Beatty Southwire Draka Kabel b.v. / Singapore Cable Manufacturer Draka USA Distribution BICC Ehlerskable Olex (Australia) Hitachi Pirelli General Power Cables Malaysia Sterling Greengate STK Alcatel AEI Kabel Metal Furukawa Electric Nexans Kerite Okonite Prysmian Hi-Essence Cable Sdn Bhd
Submarine Cable ABB Fujikura Ltd
J-Power Systems Nexans Prysmian General Cable
Cable Accessories Cable Glands Hawke ALCO BICC CMP Italsmea CMP Dunkerque Crouse-Hinds Surefit
Cable hanger Erico Jones(Stud) Nelson(Stud)
Conduit Hanger Grinnel Unistrut
Cable Runways Cable conduit Allied Tube and Conduit Alumax Easco Appleton Crouse-Hinds Occidental Coating(OCAL)
Cable Transits Hawke MCT Brattberg Ltd Grunau GmbH Nelson Roxtec
Cable Tray and Ladders AWM Cooper B Line Champion Fiberglass Enduro Orbtech Oglaend Systems Robroy Industries
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 48 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
BICC Vantrunk GKN Husky Burndy Mono Strut Metal Perforators Swifts M Rack Unistrut VanTrunk Wiremold Cope Dynac Sdn Bhd
Distribution Boards Flameproof Appleton Crouse-Hinds Killark Nelson AWM
Ducting Low Voltage Bus AWM Busduct(Cast Resin) Low Voltage Bus Betobar Electrical / Instrument Building Square D
Merlin Gerin Consafe Lectrus Leirvik Emtunga AB ABB Point Eight Power Powell Industries, Inc.
Electrical Heater Chromalox Gas Heating Stiebel Eltron
Texas Systems Heatex
Generators Diesel Engine Generator Package Atlantic Caterpillar Cummins Engine Co Cummins Lae Singapore F. G. Wilson Mitsubishi Heavy Industry (M.H.I.) Mustang Power Systems Simpson Power Simpson Power General Electric Ideal Electric Kato (Reliance) Tractors Singapore Tractor & Equipment Nigeria Limited William Adams
Generators Large (>20 MW) Generators ABB Siemens / Westinghouse
Jeaumont Alstom
GE / Nuovo Pignone Generators Small (<20MW) Generators Hyundai Ideal
Taiyo Electric Co. Kato
Generators Thermo Electric Teledyne Generators Large (>20 MW) Generators Brush Turbogenerators
GE Furse Thermoweld Wallis Companies
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 49 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Burndy Cadweld
Heat Tracing AWM Raychem Thermon Far East Ltd Chemlex Thermon Heat Tracing Services
Heat Tracing System Tyco/Raychem/Tracer Heater Water Rheem HOA, Start/Stop Buttons, Switches Allen Bradley
A.T.X. Bartec Crouse-Hinds Appleton Killark Square D Telemencanique Stahl
Junction Boxes ABTech AWM Ceag Hammond Manufacturing Hoffman Rittal Stahl Tranberg Weidmuller Appleton Crouse-Hinds Killark Nelson Govan
Lighting Beacon / Rotating Crouse-Hinds Govan Hella
Emergency AWM Fittings Crouse-Hinds General AWM Lighting Fixtures Ceag
Chalmit Lighting Chalmit Lighting Crouse-Hinds Crouse-Hinds Glamox Glamox Medc Killark Hubbel Govan Simplex Lighting Stahl Appleton
Marine Pauluhn Convenience outlets Receptacles c/w Plugs Crouse-Hinds
Appleton Hubbell
Receptacles c/w Plugs(240 Vac) MK Motors DC General Electric
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 50 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Westinghouse AC/DC Brook Crompton
Parkinson Western Electric
Low Voltage Motors ABB WEG
Siemens Energy and Automation, Inc. Fuji Reliance Toshiba Teco Westinghouse
Siemens MV/HV voltage Electric motors ABB Teco Westinghouse
Alstom Siemens Energy and Automation, Inc. Mitsubishi Electric Reliance Toshiba US Motors
Siemens Submersible Franklin Electric Synchronous Motors ABB
Alstom Hyundai Ideal Mitsubishi Electric Electric Machinery Teco Westinghouse
Siemens GE Navigational Aids Pharos Marine Automatic Power
Automatic Power Orga Tideland Signal Corp
Aircraft Obstruction Lighting Orga Tideland Signal Corp
Page / Party System Gai-Tronics Corp Spector Lumenex
Power Transformers Alstom Merlin Gerin Brush Uptegraff Virginia Mitsubishi Electric Powell / ESCO AWM Brush Transformers Ltd
Dry Type ABB GE Siemens
France Transfo SGB-Starkstorm UIC (Exicast) Square D
Power Transformers Oil Filled ABB GE
Crompton Greaves Square D
Grounding Transformers GE
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 51 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Power Distribution Transformers ABB Protection Relay Basler
General Electric Westinghouse Multilin
Switchgear / Motor Control Centers Motor Control Centers ABB Alstom
Holec Cutler Hammer Allen Bradley Point Eight Power Powell Industries, Inc. Square D Merlin Gerin Switchgear & Instrumentation Ltd Vei Power Distribution (M) Sdn Bhd
Siemens Siemens Singapore
Switchgear ABB Switchgear & Instrumentation Ltd Schneider Electric General Electric Westinghouse SACE Vei Power Distribution (M) Sdn Bhd
Alstom Holec Point Eight Power Powell Industries, Inc. Square D Merlin Gerin Siemens Siemens Singapore
ABB Westinghouse Nelson International Switchboard
Terminal Blocks Phoenix Contact Weidmuller
Transfer Switch Automatic transfer switch, ATS ASCO Uninterruptible Power System Custom Power
Gutor Sab Nife Saft Nife Saft Singapore Pte Ltd. Merlin Gerin Ametek Solidstate Controls ABB Topaz Toshiba Solid state Control Inc(SCI) Yuasa Powermatrics(Malaysia) Powernetrics(UK) Thyrec Tegas Kombinasi Sdn Bhd Siemens
AC-UPS Systems Gutor DC Power Supply System Gutor Variable Frequency Drives LV Variable Fequency Drives ABB
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 52 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Allen Bradley Square D Telemencanique Cutler Hammer Toshiba
Robicon Siemens Variable Frequency Drives MV/HV Variable Fequency Drives ABB
Siemens Mitsubishi Electric
Allen Bradley Square D Telemencanique Toshiba
Robicon
17. Structural & Architectural
Category Description Manufacturer Remarks
Insulation Dae Hyup Tech Neoprene Sheet Bakker
Bredero Trelleborg Bakker B.V. Trelleborg Hercules Trelleborg Viking
Steel Atlas Tube Grating Webforge Vic
Lionweld DAHE Industries
Deferco Clebecq Steel Plate
US Steel
JFE
Mitsui & Co. ThyssenKrupp Mannex GmbH
Mannesmann Owned by Salzgitter. Nippon Kokan
NKK Now JFE
Dillinger Hutte Nippon Steel Corp Kawasaki Steel Salzgitter Sumitomo Metal Industries, Ltd. Thyssen Stahlunion Corus Voest Alpine Posco
Steel Shapes Corus Kawasaki Steel Nippon Steel Corp Nippon Kokan (NKK) Sumitomo Metal Industries, Ltd. Arbed – Luxembourg
Structural Tubular and SMLS JFE
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 53 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Piles Sumitomo Metal Industries, Ltd. Nippon Steel Corp Nippon Kokan (NKK) Kawasaki Steel Mannesmann Corus Dalmine
Corus Structural Tubular and Piles
Sam Kang Industries ThyssenKrupp Mannex GmbH
Sumitomo Metal Industries, Ltd. Nippon Kokan (NKK) Nippon Steel Corp Osaka Tokushu KoKan (OTK) Berghor Eiserbau Kramer - Germany Westfalenwerke KG Mannesmann Graebener Preussag-Salzgitter Stahl Steel Flower - Korea
Spiral Welded Petropipe Industries
18. Marine
Category Description Manufacturer
Acceptable Manufacturing
Facility (City/Country)
Boilers Exhaust Gas Economizers
Aalborg Industries A/S Aalborg Denmark, Singapore
Manufacturers - New Aalborg Industries A/S Aalborg Denmark, Singapore
Service / Repair / Rebuild
Combustion Control Systems
Gosfern Aalborg Denmark, Singapore
Aalborg Industries A/S Aalborg Denmark, Singapore
Harris Pye Singapore Thermal Fluid Heaters Aalborg Industries A/S Aalborg Denmark,
Singapore
Cargo Transfer Double Carcass Hose With Accessories
Yokahama Rubber Company Tokyo Japan
Bassi Offshore Gironico Italy
Telleborg Clemony-Ferrand France
Dunlop Oil & Marine Houston Texas, USA
Duel Product Swivel CALM Only Blue Water Energy
Services Houston Texas, USA
Loading Arms Loading Arms up to
16 inch Niigata Loading Systems, LTD
Niigata - Japan
Emco Wheaton Houston - Texas
Kirchhain - Germany
Loading Arms up to 20 inch FMC Technologies France
Marine Breakaway Coupling MIB International Ltd. Coventry England
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 54 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Gall Thompson Env. Ltd. Norfolk England Multi Product Swivel FSO / FSPO SBM Atlantia Houston Texas, USA
Blue Water Energy
Services Houston Texas, USA
SOFEC Inc Houston Texas, USA Poduct Swivel CALM Only SBM Atlantia Houston Texas, USA
Primary Emergency Release Coupling (PERC)
Up to 20 inches FMC Technologies France
MIB ITALIANA S.P.A. Padova - Italy Inert Gas Equipment
Aalborg Industries A/S Aalborg Denmark, Singapore
Air Products A/S Kristiansand Norway Hamworthy KSE Moss AS Singapore Mooring Equipment
Bardex Corporation Goleta California, Houston Texas
Bodewes Winches Mooring Equipment
Chain Jacks Imeca Groupe Perrotin La Rochelle France
Chain Jacks Smith Berger Marine, Inc. Seattle Washington USA
Mooring Equipment
Chain Stoppers Hull Only Aker Kvaerner Maritime Pusness AS
Arendal Norway
Mooring Equipment
Chain Stoppers Imeca Groupe Perrotin La Rochelle France
Smith Berger Marine, Inc. Seattle Washington USA
Harbor & Marine Engineering
Victoria Australia
Rolls-Royce Mooring & Deck Machinery
Houston Texas, USA
Mooring Equipment Chains Ramnas Bruk Bergslagen Sweden Rolls-Royce Mooring &
Deck Machinery Houston Texas, USA
Vicinay Cadenas SA Bilbao Spain Asian Star Anchor Chain Dongxing Town Chine Mooring Equipment
Fairleads Hull only Bardex Corporation Goleta California, Houston Texas
Mooring Equipment
Fairleads Aker Kvaerner Maritime Pusnes AS
Arendal Norway
Rolls-Royce Mooring & Deck Machinery
Houston Texas, USA
Mooring Equipment
Hawser & Accessories Bridon International Ltd. Doncaster England
Cosalt Safety & Production Lincolnshire England
Scanrope Tonsberg Norway Bexco Ropes Mamme Belgium Offspring International Inc. Laguna Niguel
California USA Mooring Equipment
Hawser Life Prediction Tension Technology Int. Ltd.
East Sussex England
Ocean Tech Systems Ltd. Surrey England Mooring Equipment
Hawser Tension Monitoring
Fugro GEOS Singapore
Ocean Tech Systems Ltd. Surrey England Harbor & Marine
Engineering Victoria Australia
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 55 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
MSL Oilfield Services Ltd. Southampton England Strainstall Uk Ltd. Isle of Wight England Line Handling Boats Alnmaritec Ltd. Northumberland
England Mooring Sheaves Appleton Marine Appleton Wisconsin Mooring Equipment
Mooring Winches Appleton Marine Appleton Wisconsin
Imeca Groupe Perrotin La Rochelle France Norlau A/S Esbjerg Denmark Kocks Ostrava Hrabova
Czech Republic Rolls-Royce Mooring &
Deck Machinery Houston Texas, USA
Aker Pusnes Arendal Norway Mooring Equipment
Wire rope Hull Only Bridon Aberdeen England
Williamsport Wirerope Works Inc.
Williamsport Pennsylvania USA
Scanrope Tonsberg Norway Redaelli Wire Ropes Milano Italy Mooring Equipment
Hydralift Houston Texas USA
Mooring Equipment
Rolls-Royce Marine London England, Houston Texas USA
Pumping Systems
Deepwell Pumps Aker Kvaerner Eureka KOP
Arendal Norway
Framo Bergen Norway Hamworthy KSE Pump
Systems AS Singapore
Marflex BV Rotterdam The Netherlands
Misc. Pumps Framo Bergen Norway Pump Room Installation Hamworthy KSE Pump
Systems AS Singapore
Pump Room Installation Shinko Ind. Ltd. Hiroshima Japan Tank Venting Flame Arrestors Bolaco Valves ApS Nyborg Denmark Pres-Vac Engineering A/S Allerod Denmark High Velocity PV Valves Bolaco Valves ApS Nyborg Denmark Hankook Engineering Pte
Ltd. Singapore
Nakakita Seisakusho Co., Ltd.
Japan
Pres-Vac Engineering A/S Allerod Denmark
19. Surf (Marine)
Category Description Manufacturer
J-Lay Collar Bruck Gmbh Dalmine Forgital Italy SpA Galperti Engineering & Flow Control SRL
J-Lay Collar Cladding Foure Lagadec Galperti Engineering & Flow Control SRL HD Cladding
Miscellaneous Components for Collars Artinox
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 56 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Mooring Equipment Umbilicals (Electrical / Hydraulic Cables)
Multiflex
Nitrogen Membrane Skid Chemitrol Offshore Related Export Line Buoyancy Element
Permanent & Temporary Belmar BMTI Trelleborg CRP Cuming Corp
Stab & Hinge Over Citba VIV Suppression Strakes Advance Products and Systems
Allbrown Universal Components Anglitemp Avon Technical Products Trelleborg CRP Dunlaw
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 57 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
20. Forging Refer document below for list of acceptable manufacturers for forging
Forging Manufacturers EMDC Materials Group List of Qualified Forging List (QFL) According with MPDS 29-01-31
Rev. 3 – th November 2010
58 of 114
NOTES
1) EMDC requires that all critical carbon and alloy steel forgings shall be procured from qualified suppliers. The following product forms are covered by this Qualified Forging List:
• Tubing hangers
• Tubing head adapters
• Tree cap body
• Valve bodies, blocks and/or bonnets (see note 6 below)
• Connectors
• Choke bodies
• Manifold valve bodies and/or bonnets (see note 6 below)
• Taper joint forgings
• Flex joint forging
• Ball valves
2) This Qualified Forging List (QFL) identifies those forging manufacturers that have been technically assessed to supply forgings for onshore and offshore applications in accordance with MPDS 29-01-31
3) Manufacturers are qualified to supply the material grades, product forms, and sizes ranges as defined in the table.
4) Manufacturers are restricted to the restrictions shown and manufacturing processes shown under comments. A change shall invalidate
the manufacturer’s qualification.
5) Manufacturer shall have performed a technical audit of their sub-suppliers and details of this technical audit shall be made available to Company upon request.
6) EMDC accepts that certain manufacturing processes may be carried out by sub-suppliers. EMDC shall be advised if a change is made
which covers the following activities.
• Supply of raw material
• Forging
• Heat treatment
• Laboratory testing services
• N.D.E Services
7) QFL also includes forging manufacturers that have been used on previous Company projects. No information on performance or quality is available. Company has not endorsed these suppliers due to insufficient knowledge of suppliers quality. If Project desires to use these suppliers, then technical assessment is required.
Forging Manufacturers EMDC Materials Group List of Qualified Forging List (QFL) According with MPDS 29-01-31
Rev. 3 – th November 2010
59 of 114
8) Forging shaping operations may be performed by hammering, pressing, piercing, extruding, upsetting, rolling, bending or by a combination of all. Flanges, elbows, bends, tees, valve bodies, hangers, and/or manifolds shall not be machined directly from forged or wrought bar without written approval by Company.
9) If forgings have been purchased through a Stockist ( company who sub contracts processes to multi sub suppliers, and is also capable
of performing some manufacturing processes within). Stockist shall have performed a technical audit on their sub-suppliers and obtain appropriate Manufacturing Procedure Specification’s (MPS’s), which provides details of all critical operations performed on forgings being supplied for Company projects
10) It shall be the Stockists responsibility to ensure that sub-suppliers comply with the requirements of MPDS 29-01-31.
11) Details of technical audit reports along with MPS’s shall be made available to Company upon request. Under these circumstances,
Company reserves the right to carry out assessment of sub-suppliers in accordance with MPDS 29-01-31.
12) For general queries call Manuel Maligas ( + 1 281 654 5626) or Geoff Dunn ( + 1 281 654 4870) EMDC Materials Department. Greenspoint 6, Houston
Forging Manufacturers EMDC Materials Group List of Qualified Forging List (QFL) According with MPDS 29-01-31
Rev. 3 – th November 2010
60 of 114
Updated Rev No.
Manufacturer Location Product Forms Applicable Alloys
Restrictions Scope of Work
Howco Quality Alloys
Sheffield, UK Open die forgings (rolled ring, flanges, valves)
Carbon, alloy, stainless steels (F6NM, 410) and nickel alloys
Forging and bar stock. Forging are purchased from multiple sub-suppliers. Supply management company
Stockist purchases forgings from multiple sub suppliers. Capable of performing heat treatment, NDE and mechanical testing within.
Fomas Osnago, Italy Open die (valve bodies, shafts)
Carbon, alloy and stainless steels (F6NM, 410)
Forgings, < 40,000 kg Forging, heat treatment, NDE and mechanical testing performed within
ASFO Chiuppano, Italy Rolled rings Carbon and alloy Forgings, <9,000 Kg Forging, heat treatment, NDE and mechanical testing performed within
Ellwood Texas Forge
Houston Open die forgings (rolled ring, flanges, valves)
Carbon, alloy and stainless
Open die forgings <80,000 lbs, length 50 feet, diameter 90 inches
Melting, forging, heat treatment, NDE and mechanical testing performed within
Forgiatura Mame
Camuno, Italy Open die, shafts Carbon, alloy and stainless
Open die forgings 1,000-40,000 kg, length 15,000 mm, diameter 3,000 mm
Forging, heat treatment, NDE and mechanical testing performed within
Forgital Vicenza, Italy Rolled rings Carbon, alloy, aluminum, titanium
Rolled rings <3,000 mm diameter
Forging, heat treatment, NDE and mechanical testing performed within
Frisa Nuevo Leon, Mexico
Forged, seamless and rolled rings, flanges
Carbon, alloy, stainless and nickel base
Rings 10 kg – 40 tons, max diameter 8,000 mm
Forging, heat treatment, NDE and mechanical testing performed within
Gulfco Beaumont, Texas Rings, flanges, shape dies, discs, shafts
Carbon, alloy and stainless
Rings – <36,000 lbs, open die forgings- 20,000 lbs
Forging, heat treatment, NDE and mechanical testing performed within
Metallurgica Siderforge
Cogollo del Cengio, Italy
Roll ring, open and close die forgings, valves
Carbon, alloy, and stainless
Ball valve forgings to 24 in, forgings 5000 kg, roll rings 2,500 mm OD x 200 mm ID
Forging, heat treatment, NDE and mechanical testing performed within
MetalCam Breno, Italy Open die forgings, flanges, shafts
Carbon, alloy and stainless
Open Die forgings, <6,000 kg
Melting, forging, heat treatment, NDE and mechanical testing performed within. Thirty Five (35) ton melting facility in house
Updated Rev No
Manufacturer Location Product Forms Applicable Alloys Restrictions Scope of Work
Forging Manufacturers EMDC Materials Group List of Qualified Forging List (QFL) According with MPDS 29-01-31
Rev. 3 – th November 2010
61 of 114
Sheffield Forgemasters
Sheffield, UK Open die forgings Carbon, alloy and stainless
Bars and ingots for further processing
Melting facility
W F I Bonney Forge
Houston, Texas Open die flanges and fittings
Carbon and alloy Butt weld fittings, flanges
Forging, heat treatment, NDE and mechanical testing performed within
Custom Alloys High Bridge, NJ Open die, flanges and fittings
Carbon and alloy <250 kg Forging, heat treatment, NDE and mechanical testing performed within
MEGA Bergamo, Italy Piggable Y’s Carbon steel Piggable Y’s Subcontracts forging and heat treatment.
ASO Siderurgica Ospitaletto, Italy Bar Carbon, alloy and 3XX stainless steel with Carbon>.03%
Bars supplied only in non-heat treated condition
Supplier of bars in non heat treated condition to be re-forged or heat treated.
Ringmill Dubino, Italy Open die forgings, valves Carbon, alloy and stainless
<1,500 kg close die, <18,000 kg rings and <36,000 kg open die
Approved by reputation. Forging, heat treatment, NDE and mechanical testing performed within
Eastham Forge Beaumont Open die forgings Carbon, alloy and stainless
<13,000 kg Forging only
Riganti S.P.A. Solbiate Arno, Italy
Close die Carbon, alloy and Stainless
<500 Kg Forging, heat treatment, NDE and mechanical testing performed within
Lucchini RS Lovere (BG), Italy Open die Carbon, alloy and stainless
<15000 Kg Melting, forging, heat treatment, NDE and mechanical testing performed within.
Forge Fedriga Cividate Camuno, Italy
Open die Carbon, alloy and stainless
<5000 Kg Forging, heat treatment, NDE and mechanical testing performed within
TD Forge Domaso Italy Open die Carbon, alloy and stainless
<2200 Kg Forging, heat treatment, NDE and mechanical testing performed within
Forgerossi Italy Open die forgings Carbon, alloy and stainless
On AML
C.A.F. Spain Open die forgings Carbon, alloy and stainless
On AML
Melesi Italy Open die forgings Carbon, alloy & stainless
On AML
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 62 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
21. Duplex Stainless Steel Refer document below for list of acceptable manufacturers for duplex stainless steel
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
63 of 114
NOTES
EMDC requires that all duplex and super duplex stainless steel materials shall be procured only from qualified suppliers. To become qualified, a
supplier must have satisfied the requirements of MPDS 29-01-04.
This Qualified Manufacturers' List (QML) identifies those suppliers that have been assessed in accordance with MPDS 29-01-04 and found
capable of supplying Duplex and Super Duplex material conforming to MPDS 29-01-02.
Manufacturers are qualified to supply the material grades, product forms, and sizes ranges as defined in the attached table.
Manufacturers are restricted to the use of the mandatory sub-suppliers listed in the attached table. A change in a mandatory sub-supplier shall
invalidate the manufacturer's qualification.
The following product forms are covered by this Qualified Manufacturing List:
- Bar (see note 7 below)
- Castings
- Fittings
- Forgings (see note 7 below)
- Induction Bends
- Plate
- Pipe (Seamless)
- Pipe (Long Seam Welded - not spiral welded pipe)
- Semi-finished Billet
Section sizes at final heat treatment in excess of 200 mm for 22 Cr duplex and 120 mm for 25 Cr super duplex are outside the scope of this
document and shall be subject to approval on a case by case basis.
Flanges, elbows, bends, plates, discs, tees, valve bodies, headers and manifolds shall not be machined directly from forged or wrought bar.
Forging shaping operations may be performed by hammering, pressing, piercing, extruding, upsetting, rolling, bending or by a combination of
two or more of these operations Small cylindrically shaped items may be machined from forged bar only with the express written approval of
ExxonMobil
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
64 of 114
The evaluation for acceptance shall include a visit to the manufacturers and, where necessary, sub-supplier's premises to review facilities, systems,
implementation of procedures and documentation as required by MPDS 29-01-04.
EMDC accepts that certain manufacturing processes may be carried out by a sub-supplier. Under these circumstances EMDC reserves the right to
carry out an assessment of mandatory sub-suppliers in accordance with MPDS 29-01-04. Also the supplier shall advise EMDC if there is a
change in any mandatory sub-supplier. Mandatory sub-suppliers will be those which cover the following activities
• Supply of raw material
• Supply of semi or part finished product
• Manufacturing processes such as forming, forging, casting and welding, including weld repair.
• Heat treatment
• Laboratory testing services.
• N.D.E. Services
During manufacture it shall be the manufacturer's responsibility to ensure that its sub-suppliers comply with the requirements of MPDS 29-01-02
and MPDS 29-01-04. Details of sub-suppliers will be made available to EMDC upon request.
The QML shall be revised and reissued to interested parties at frequency determined by EMDC.
EMDC shall monitor the performance of manufacturers and their sub-suppliers to ensure that the list of qualified manufacturer can be maintained.
The manufacturer and all sub-suppliers shall hold current accreditation to ISO 9000 or another recognized quality system acceptable to EMDC.
For general queries call Derek Horsburgh (+1 281 654 5507) or Bart Tarleton (+1 281 654 4960) EMDC, Materials Department, Greenspoint 6,
Houston.
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
65 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
10 Bar 22Cr Foroni, Gorla Minore, (VA), Italy
A276 UNS S31803
200 mm No weight restriction
Wrought Bar
9 Bar 22Cr Sandvik, Sandviken, Sweden
A276 S31803 Production Route I: 20 - 75 mm OD Production Route II: 75 - 145 mm OD Production Route III 150 - 200 mm OD No weight restriction
Wrought Bar Production Route I; Final forming and heat treatment by Scana Soderfors AB
13 Bar 22Cr Scana Stavanger, Jorpelaan, Norway
A276 S31803 < 200 mm Diameter No weight restriction
Wrought Bar (Press Forged)
Base Material from Scana Stavanger Heat Treatment from Furnaces 112 and 113
13 Bar 22Cr BGH Edelstahl, Siegen, Germany
A276 S31803 < 200 mm Diameter No weight restriction
Forged Bar (Ingot Route)
Base Material from BGH Siegen Solution annealing in Furnaces 23, 24, 25, 26 and 27
14 Bar 22CR BGH Edelstahl, Freital, Germany
A276 S31803 < 64 mm Rolled Bar (Con cast)
Base material from BGH Freital Solution annealing in Furnace 474
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
66 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Bar 22Cr BGH Edelstahl, Siegen, Germany
A276 S31803 < 200 mm Diameter
Forged Bar (Ingot Route)
Base Material from BGH Siegen Solution annealing in Furnaces 23, 24, 25, 26 and 27
14 Bar 22CR BGH Edelstahl, Freital, Germany
A276 S31803 < 121 mm Forged Bar (Con cast)
Base material from BGH Freital Solution annealing in Furnace 722
13 Bar 25Cr BGH Edelstahl, Siegen, Germany
A276 S32760 < 120 mm Diameter
Forged Bar (Ingot Route)
Base Material from BGH Siegen Solution annealing in Furnaces 23, 24, 25, 26 and 27
14 Bar 25CR BGH Edelstahl, Freital, Germany
A276 S32750 < 64 mm Rolled Bar (Con cast)
Base material from BGH Freital Solution annealing in Furnace 474
14 Bar 25CR BGH Edelstahl, Freital, Germany
A276 S32750 < 120 mm Forged Bar (Con cast)
Base material from BGH Freital Solution annealing in Furnace 722
14 Bar 25CR BGH Edelstahl, Freital, Germany
A276 S32760 < 64 mm Rolled Bar (Con cast)
Base material from BGH Freital Solution annealing in Furnace 474
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
67 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
14 Bar 25CR BGH Edelstahl, Freital, Germany
A276 S32760 < 120 mm Forged Bar (Con cast)
Base material from BGH Freital Solution annealing in Furnace 722
8 Bar 25Cr Foroni, Gorla Minore, (VA), Italy
A276 UNS S32760 UNS S39277
120 mm No weight restriction
Wrought Bar
14 Bar 25Cr Rolled Alloys Technology Limited, Blackburn, UK
A276 S32760 6.35 – 120 mm Wrought Bar Formerly Weir Materials
11 Bar 25Cr Sandvik, Sandviken, Sweden
A276 S32750 Production Route I: 20 - 75 mm OD Production Route II: 75 - 120 mm OD No weight restriction
Wrought Bar Production Route I; Final forming and heat treatment by Scana Soderfors AB
13 Bar 25Cr Scana Stavanger, Jorpelaan, Norway
A276 S32760 < 120 mm Diameter No weight restriction
Wrought Bar (Press Forged)
Material from Scana Stavanger Heat Treatment from Furnaces 112 or 113
13 Castings 22Cr Doncasters Paralloy Ltd, Billingham, UK
A890 Gr. 4A (UNS J92205)
t < 200 mm No weight restriction
Gravity sand Castings
Melt from 100% AOD – no returns or scrap added Heat treatment: In house or by ConMech Engineers Ltd. All weld repairs shall be solution annealed. FFS testing by Exova Teesside.
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
68 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
10 Castings 22Cr Fondinox, Sergnano, (Cr), Italy
A890 Gr. 4A (UNS J92205)
t< 130 mm No weight restriction
Centrifugal cast Balls
10 Castings 22Cr Fondinox, Sergnano, (Cr), Italy
A890 Gr. 4A (UNS J92205)
t< 94 mm No weight restriction
Centrifugal cast Tubes
10 Castings 22Cr Fondinox, Sergnano, (Cr), Italy
A890 Gr. 4A (UNS J92205)
t < 160mm No weight restriction
Gravity sand Castings
10 Castings 22Cr Norton Cast Products, Sheffield, UK.
A995 Gr. 4A (UNS J92205)
t < 134 mm Weight Unlimited
Gravity sand Castings
Heat treatment: By NCP or Special Steel Company Ltd., Sheffield, procedure NCP H/T 02. All weld repairs shall be solution annealed. Testing by MTT or another test lab acceptable to EMDC
9 Castings 22Cr Wm. Cook Hi Tec Integrity Castings, Parkway, Sheffield, UK
A890 Gr. 4A (UNS J92205)
t < 156 mm No weight limit
Sand Castings
Testing to be by an accredited external laboratory acceptable to EMDC.
14 Castings 22Cr Mathers Foundry Ltd, Manchester, UK
A 890 Gr 4A (J92205)
t < 200 mm No weight limit
Gravity sand castings
Formerly Weir Foundries AOD starting material in-house, from Goodwins Steel Castings or Avesta Sheffield No revert / foundry returns
4 Castings 22Cr Brafe Engineering, Woodbridge, Suffolk, UK
A 890 Gr 4A (J92205)
T < 100 mm No weight limit
Gravity sand castings
Testing to be by an accredited external laboratory acceptable to EMDC.
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
69 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
4 Castings 22Cr Brafe Engineering, Woodbridge, Suffolk, UK
A 890 Gr 4A (J92205)
T < 45 mm 18 kg max weight
Repliwax (Lost wax process)
Testing to be by an accredited external laboratory acceptable to EMDC
14 Castings 22Cr Goodwin Steel Castings,
SStoke on TTrent, UK
A 890 Gr 4A (J92205)
T < 200 mm No weight limit
Gravity sand castings
Testing in-house or at Exova Netherton, or Special Testing Labs, Sheffield. GSC’s image analysis system is acceptable for the determination of ferrite content.
6 Castings 22Cr Highland Foundries, Surrey, BC, Canada
A 890 Gr 4A T < 200 mm No weight limit
Gravity sand castings
AOD Production route only
8 Castings 22Cr Furniss and White, Sheffield, UK
A890 Gr 4A (J92205)
T < 190 mm No weight restriction
Gravity sand castings
New weld repair procedures to be qualified. Testing by CoMech, Derby or another test house acceptable to EMDC.
8 Castings 22Cr BEL Foundry, Newcastle, UK
A890 Gr 4A T < 115 mm Max weight 258 kgs
Gravity sand castings
No major weld repairs allowed, all repairs shall be as welded. PMI by PMI Services Limited
8 Castings 22Cr Noel Village Steel Founders, Doncaster, UK
A890 Gr 4A T < 200 mm No weight restriction
Gravity sand castings
Testing by CoMech Derby or another test house acceptable to EMDC. Heat treatment by Bodycote (formerly Expert Heat Treatments) of Stillington, Cleveland
9 Castings 22Cr MetalTek International, Pevely, MO
A890 Gr 4A T < 178 mm, No weight restriction
Gravity sand castings
Heat Treatment in Furnace F1 Testing by St Louis Testing Laboratory or another test house acceptable to EMDC.
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
70 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Castings 22Cr Bonds Precision, Alston, Cumbria
A995 Gr. 4A 100 mm max Gravity fed, Shaw ceramic process
Testing to be carried out by MIS Consett, or another laboratory acceptable to EMDC
9 Castings 25Cr Wm. Cook Hi Tec Integrity Castings, Parkway, Sheffield, UK
A890 Gr. 5A (UNS J93404)
t < 120 mm No weight limit
Gravity sand castings
Testing to be by an accredited external laboratory acceptable to EMDC.
13 Castings 25Cr Doncasters Paralloy Ltd, Billingham, UK
A890 Gr. 6A (UNS J93380)
t < 120 mm No weight restriction
Gravity sand castings
Melt from 100% AOD – no returns or scrap added Heat treatment: In house or by ConMech Engineers Ltd. All weld repairs shall be solution annealed. FFS testing by Exova Teesside.
10 Castings 25Cr Fondinox, Sergnano, (Cr), Italy
A890 Gr. 5A (UNS J93404)
t < 120 mm No weight restriction
Centrifugal cast Balls
All weld repairs shall be solution annealed.
10 Castings 25Cr Fondinox, Sergnano, (Cr), Italy
A890 Gr. 5A (UNS J93404)
t < 85 mm No weight restriction
Centrifugal cast Tubes
All weld repairs shall be solution annealed.
10 Castings 25Cr Fondinox, Sergnano, (Cr), Italy
A890 gr. 5A (UNS J93404)
t < 120mm No weight restriction
Gravity sand castings
All weld repairs shall be solution annealed.
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
71 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Castings 25Cr Mathers Foundry Limited, Manchester, UK
A890 Gr 6A (J93380)
t < 120mm, No weight limit
Gravity sand castings
Formerly Weir Foundries AOD starting material in-house, from Goodwins Steel Castings, or from Avesta Sheffield. No revert / foundry returns
14 Castings 25Cr Goodwin Steel Castings, Stoke on Trent, UK
A 890 Gr 6A (J93380)
T < 120 mm No weight limit
Gravity sand castings
Testing in-house or at Exova Netherton or Special Testing Labs, Sheffield. GSC’s image analysis system is acceptable for the determination of ferrite content.
4 Castings 25Cr Brafe Engineering, Woodbridge, Suffolk, UK
A 890 Gr 6A (J93380)
T < 80 mm No weight limit
Gravity sand castings
Testing to be by an accredited external laboratory acceptable to EMDC.
4 Castings 25Cr Brafe Engineering, Woodbridge, Suffolk, UK
A 890 Gr 6A (J93880)
T < 45 mm 18 kg max weight
Repliwax (Lost wax process)
Testing to be by an accredited external laboratory acceptable to EMDC.
7 Castings 25Cr Highland Foundries, Surrey, BC, Canada
A 890 Gr 5A A 890 Gr 6A
T < 120 mm No weight limit
Gravity sand castings
AOD Production route only
8 Castings 25Cr Furniss and White, Sheffield, UK
A890 Gr 6A (J93380)
T < 120 mm No weight restriction
Gravity sand castings
New weld repair procedures to be qualified. Testing by CoMech, Derby or another test house acceptable to EMDC.
8 Castings 25Cr Noel Village Steel Founders, Doncaster UK
A890 Gr 6A T < 120 mm No weight restriction
Gravity sand castings
Testing by CoMech Derby or another test house acceptable to EMDC. Heat treatment by Bodycote (formerly Expert Heat Treatments) of Stillington, Cleveland
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
72 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Castings 25Cr Schmidt and Clemens, Lindar, Germany
A890 Gr 5A T < 28 mm No weight restriction
Centrifugal Castings
Melting practice in accordance with Arbeitsanweisung 4300/38 Rev 1. Heat treatment in Furnace No 367. Hest treatment in accordance with Heat Treatment Instruction G 4470 and G4469 Rev 09/12/09. Testing by Schmidt and Clemens or another laboratory acceptable to EMDC. No weld repairs allowed
13 Castings 25Cr Bonds Precision, Alston, Cumbria
A995 Gr. 5A 62.5 mm max Gravity fed, Shaw ceramic process
Testing to be carried out by MIS Consett, or another laboratory acceptable to EMDC
13 Castings 25Cr Bonds Precision, Alston, Cumbria
A995 Gr. 6A 55 mm max Gravity fed, Shaw ceramic process
Testing to be carried out by MIS Consett, or another laboratory acceptable to EMDC
12 Castings 25Cr Norton Cast Products, Sheffield, UK.
A995 Gr. 6A (UNS J93380)
t < 125 mm Weight Unlimited
Gravity sand castings
Heat treatment: By NCP or Special Steel Company Ltd., Sheffield, procedure NCP H/T 02. All weld repairs shall be solution annealed. Testing by MTT or another test lab acceptable to EMDC
13 Fittings 22Cr GAM Raccordi, Gazzola, (PC) Italy
A815 S31803 < = 60 mm 1/2 " - 20 " OD
Hot Formed Seamless from Pipe
MDS 01/DUPL/05 Base Material from DMV Montbard or Wyman Gordon, Livingston Heat Treatment from Furnace # 5
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
73 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Fittings 22Cr GAM Raccordi, Gazzola, (PC) Italy
A815 S31803 < = 60 mm 1/2" - 36" OD
Hot Formed Seamless from Trepanned Forged Bar
MDS 02/DUPL/05 Base Material from Forge Federiga, Foroni, Sandvik, Valbruna Heat Treatment from Furnace # 5
13 Fittings 22Cr GAM Raccordi, Gazzola, (PC) Italy
A815 S31803 < = 60 mm 6" - 48" OD
Hot Formed Seamless and Welded From Plate
MDS 03/DUPL/05 Base Material from Outokumpu (Degerfors) and Usinor (Fabrique de Fer and Le Creusot) Heat Treatment from Furnace # 5
13 Fittings 22Cr GAM Raccordi, Gazzola, (PC) Italy
A815 S31803 < = 35 mm 6" - 48" OD
Hot Formed Elbows Welded from Plate in Two Halves
MDS 04/DUPL/05 Base Material from Outokumpu (Degerfors) and Usinor (Fabrique de Fer and Le Creusot) Heat Treatment from Furnace # 5
13 Fittings 22Cr GAM Raccordi, Gazzola, (PC) Italy
A815 S31803 < = 13 mm 6" - 24" OD
Cold Formed Elbows Welded from Plate in Two Halves
QTR 05/DUPL/05 Base Material from Outokumpu (Degerfors and Avesta) and Usinor (Le Creusot) Heat Treatment from Furnace # 5
10 Fittings 22Cr Wilhelm Schulz, Krefeld, Germany
A815 S31803 t < = 31.75 mm (Caps up to 37.5 mm)
Seamless and Welded Cold Formed
Seamless pipe from DMV Montbard Plate from Thyssen Krupp, Outukumpu (Degerfors and KBR Mill) Final heat treatment in Wilhelm Schulz Krefeld Fittings Plant or at the Special Annealing Plant Hulserstrasse
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
74 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
6 Fittings 22Cr IBF, Piacenza Italy
A815 S31803 3 - 27 mm thick 4 to 60" OD
Hot formed welded fittings from plate.
Process Route 1 Base material from Thyssen, Avesta (Outokumpu) Sweden, Avesta (Outokumpu) Sheffield, Krupp, Fabrique de Fer (Industeel) Belgium, Ugine (formerly ALZ).
6 Fittings 22Cr IBF, Piacenza Italy
A815 UNS S31803
5 - 33 mm thick 4" to 24" OD
Hot Formed Seamless Fittings
Process Route 4 Base material from Tubacex, Sandvik, Schoeller-Bleckmann, SMTS Montbard and Costa Volpino (formerly DMV), Foroni/IBF Vittuone
6 Fittings 22Cr IBF, Piacenza Italy
A815 UNS S31803
2.7 - 18 mm thick Up to 16" OD
Cold Formed Fittings, Seamless and Welded
Process Route 5 Base material from: Seamless; Sandvik, Tubacex, Schoeller-Bleckmann, SMTS Montbard and Costa Volpino (formerly DMV), Foroni/IBF Vittuone Plate Thyssen, Avesta (Outokumpu) Sweden, Avesta (Outokumpu) Sheffield, Krupp, Fabrique de Fer (Industeel) Belgium, Ugine (formerly ALZ)
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
75 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
12 Fittings 22Cr SSE International, Dudley, UK
A815 UNS S31803
2.7 - 17 mm 1/2 to 8" OD
Cold Formed Seamless Fittings
Heat treatment in house. Testing, including PMI and FFS, by Exova, Netherton or another test house acceptable to EMDC. Intermediate stress relief solution anneal may be performed Base material from Tubacex, Schoeller-Bleckmann, Sandvik, DMV Montbard, DMV Costa Volpino This qualification relates to the material quality only and does not constitute an approval of the fitting design.
14 Fittings 25Cr Rolled Alloys Technology Limited, Blackburn, UK
A815 S32760 2.77 - 17.83 mm 0.5 - 8" NPS
Formerly Weir Materials
6 Fittings 25Cr IBF, Piacenza Italy
A815 S32760 3 - 24 mm thick 4" to 60" OD
Hot formed welded fittings from plate.
Process Route 1 Base material from Bohler, Industeel Creusot (formerly CLI), Outokumpu.
6 Fittings 25Cr IBF, Piacenza Italy
A815 S32760 14 - 24 mm thick 4" to 24" OD
Hot Formed Seamless Fittings
Process Route 4 Base material from Industeel Creusot (formerly CLI), Foroni/IBF Vittuone
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
76 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
6 Fittings 25Cr IBF, Piacenza Italy
A815 S32760 2.7 - 9 mm thick Up to 16" OD
Cold Formed Fittings, Seamless and Welded
Process Route 5 Base material from: Seamless; Tubacex, Schoeller-Bleckmann, Foroni/IBF Vittuone Plate Bohler, Outokumpu, Industeel Creusot and Belgium
10 Fittings 25Cr Wilhelm Schulz, Krefeld, Germany
A815 S32750 t < = 27.5 mm (Caps up to 33.75 mm)
Seamless and Welded Cold Formed
Seamless pipe from Sandvik, Sandviken, Plate from CLI (Le Creusot) and Bohler, Kapfenberg Final heat treatment in Wilhelm Schulz Krefeld Fittings Plant or at the Special Annealing Plant Hulserstrasse
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
77 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
10 Fittings 25Cr Wilhelm Schulz, Krefeld, Germany
A815 S32760 t < = 27.5 mm (Caps up to 31.25 mm)
Seamless and Welded Cold Formed
Seamless pipe from DMV Remscheid and Schoeller Bleckmann, Ternitz. Plate from CLI (Le Creusot) and RA Materials (Formerly Weir Materials) Limited (Manufacturing Works Number C25739902 only) Final heat treatment in Wilhelm Schulz Krefeld Fittings Plant or at the Special Annealing Plant Hulsertrasse
13 Fittings 25Cr GAM Raccordi, Gazzola, (PC) Italy
A815 S32750 T < = 11 mm ½” – 8” OD
Hot Formed Seamless from Pipe
QTR 01/750/05 Seamless Pipe from Sandvik, Sandviken Heat Treatment from Furnace # 5
13 Fittings 25Cr GAM Raccordi, Gazzola, (PC) Italy
A815 S32750 < = 38 mm 2" - 36" OD
Hot Formed Seamless and Welded Fittings from Plate
QTR 02/750/05 Plate from Outukumpu Degerfors and Industeel (Creusot) Heat Treatment from Furnace # 5
13 Fittings 25Cr GAM Raccordi, Gazzola, (PC) Italy
A815 S32750 < = 32 mm 4" - 36" OD
Hot Formed Seam Welded Elbows from Two Halves From Plate
QTR 03/750/05 Plate from Outukumpu Degerfors and Industeel (Creusot) Heat Treatment from Furnace # 5
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
78 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Fittings 25Cr GAM Raccordi, Gazzola, (PC) Italy
A815 S32760 < = 23 mm ½” - 8" OD
Hot Formed Seamless from Pipe
QTR 01/760/05 Seamless Pipe from SMTS Montbard France Heat Treatment from Furnace # 5
13 Fittings 25Cr GAM Raccordi, Gazzola, (PC) Italy
A815 S32760 < = 40 mm ½” - 24" OD
Hot Formed from Hollowed Forged Bar
QTR 02/760/05 Forged Bar from: Brietenfeld, Mitterdorf, Germany Pipe from Forged Bar from: IBF Vittuone / Foroni, Italy Heat Treatment from Furnace # 5
13 Fittings 25Cr GAM Raccordi, Gazzola, (PC) Italy
A815 S32760 < = 32 mm 2" - 36" OD
Hot Formed Fittings from Plate Rolled and Welded with 1 Seam
QTR 03/760/05 Plate from: Thyssen Krupp Nirosta and Industeel (Creusot) Heat Treatment from Furnace # 5
13 Fittings 25Cr GAM Raccordi, Gazzola, (PC) Italy
A815 S32760 < = 34 mm 4" - 36" OD
Hot Formed Seam Welded Elbows from Two Halves From Plate
QTR 04/760/05 Plate from: Thyssen Krupp Nirosta;Industeel (Creusot); Bohler Bleche Heat Treatment from Furnace # 5
12 Forgings 22Cr Forgiatura Marcora Srl, Olgiate Olona (VA) Italy
A182 F 51 (UNS S31803)
t < 200 mm No weight limit
Rings Open die Forged
Heat treatment by Sorbit furnace islands F6 or F10 Base material Cogne, Valbruna, Aceria de Alava Testing by Sigmatre or another test house acceptable to EMDC
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
79 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
14 Forgings 22Cr Inoxfucine, Montanaso, (LO), Italy
A182 F 51 (UNS S31803)
d < 120 mm g < 451 kgs
Open Die Hammer Bars
Billet from Aceralava, Cogne & Foroni Manufacturing Specification MS130/G
14 Forgings 22Cr Inoxfucine, Montanaso, (LO), Italy
A182 F 51 (UNS S31803)
d < 200 mm No weight restriction
Free Forging Press Bars
Billet from Aceralava, Cogne & Foroni Manufacturing Specification MS131/G
14 Forgings 22Cr Inoxfucine, Montanaso, (LO), Italy
A182 F 51 (UNS S31803)
t < 200 mm No weight restriction
Free Forging Press Rings
Billet from Aceralava, Cogne & Foroni Manufacturing Specification MS133/G or 134/G
14 Forgings 22Cr Inoxfucine, Montanaso, (LO), Italy
A182 F 51 (UNS S31803)
t < 200 mm No weight restriction
Free Forging Press Discs
Billet from Aceralava, Cogne & Foroni Manufacturing Specification MS140/G
14 Forgings 22Cr Inoxfucine, Montanaso, (LO), Italy
A182 F 51 (UNS S31803)
t < 200 mm No weight restriction
Open Die Press Nozzles
Billet from Aceralava, Cogne & Foroni Manufacturing Specification MS141/G or 142/G
14 Forgings 22Cr Inoxfucine, Montanaso, (LO), Italy
A182 F 51 (UNS S31803)
t < 200 mm No weight restriction
Free Forging Press Flat Bar
Billet from Aceralava, Cogne & Foroni Manufacturing Specification MS143/G
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
80 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
7 Forgings 22Cr Melesi, Cortenove, Lecco, Italy
A182 F 51 (UNS S31803)
T<200 mm T<64 mm T<120 mm T<200 mm T<104 mm No weight restriction
Open Die Pressed and Ring Rolled Open Die Hammer Open Die Pressed Closed Die Hammer Closed Die Press Forged
Billet materials from Techphy, ABS Safau, Aceralava, Foroni, Sandvik, Cogne, Industeel (Creusot), Outokumpu (Degerfors), Trinecke Zelezarny.
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
81 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
14 Forgings 22Cr Spromak, Liverpool, UK
ASTM A182 Gr F51 (UNS S31803)
Max t = 82 mm Max weight = 25 kg
Closed Die Forged
Forging by Dyform-Jenkins-Dunn. Note Spromak also use fully forged and heat treated items from Abbey Forge Sheffield. Heat Treatment by Darlington Heat Treatment Testing by Exova Netherton, Salford or Tees-side or another test laboratory acceptable to EMDC Material from Valbruna Aceralava, Cogne, BGH Freital, Foroni, Sandvik, Outokumpu and Olara This qualification relates to the material quality only and does not constitute an approval of the fitting design.
1 Forgings 22Cr Bruck, Ensheim, Germany
ASTM A182 F51 (UNS S31803)
38 to166 mm. Contour Forged and/or Ring Rolled
Billet from Foroni, Cogne and Bohler
2 Forgings 22Cr Ringmill, Dubino (SO), Italy
ASTM A182 F51 (UNS S31803)
T < 200 mm T < 200 mm T < 200 mm
Closed Die Open Die + Ring Rolled Open Die
All billet from Foroni. Open and Closed Die forging by press forging.
8 Forgings 22Cr Eastham Forge, Beaumont, TX
ASTM A182 F51 (UNS S31803)
200 mm No max weight restriction
Open Die / Hammer / Press
Billet from Atlas Steel, Canada or from Foroni, Italy
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
82 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
5 Forgings 22Cr Metallurgica Siderforge, Cogollo del Cengio, (VI), Italy
ASTM A182 F51 (UNS S31803)
T < 196 mm T < 200 mm T < 200 mm
Closed Die Open Die + Ring Rolled Open Die
Billet from Cogne, Valbruna or ABS Safau. Open and Closed Die forging by press forging. See report for full range of approval.
6 Forgings 22Cr ASFO, Chiuppano, (VI), Italy
ASTM A182 F51 (UNS S31803)
200 mm Open die + Ring Rolled
Billet from Cogne, Foroni and Aceralava Metallography at Lab San Marco or another laboratory acceptable to EMDC.
14 Forgings 22Cr FEAT, Cesana Brianza, (LC), Italy
ASTM A182 F51 (UNS S31803)
T < 81 mm Up to 7 kgs
Closed Die Press Forged
Testing by Sigmatre or another laboratory acceptable to EMDC. Final heat treatment to be carried out by Sorbit. Billet from Acciaierie Valbruna
13 Forgings 22Cr Stooss, Hedingen, Switzerland
ASTM A182 F51 (UNS S31803)
T < 190 T < 135 T < 38
Open die pressed Open die pressed and ring rolled Hammer forged and ring rolled
Billet from Foroni or Bohler. Metallographic testing at Exova Crema, SMT Pozzo d’Adda, or another laboratory acceptable to EMDC
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
83 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
14 Forgings 22Cr Galperti s.r.l., Cortenova, Lecco, Italy
ASTM A182 F51
200 mm max No weight restriction
Closed die, press forged; Closed die press forged and ring rolled
Heat treatment in furnace H2 and in tank number HTT2 Testing by AQM, Sigmatre or another laboratory acceptable to EMDC. Base material from Cogne or Sandvik
13 Forgings 22Cr Special Quality Alloys (SQA), Sheffield, UK
A182 F51 (UNS S31803)
T< 200 (was 150) mm No max. weight restriction
Open Die Hammer; Blanks and Rings
Billet from Foroni, Cogne, Sandvik, Scana, or BGH. Heat Treatment in Furnace No. 7 at Special Steels Forging by, IFA Limited Sheffield, Forge UK, Sheffield or Special Forged Products Limited Sheffield. Testing by Special Testing Limited or another laboratory acceptable to EMDC.
13 Forgings 22Cr Howco Quality Alloys / Howco Metals Management, Sheffield,
ASTM A182 F51
200 mm Pressed and / or Hammer Forged
Heat treatment in Howco Sheffield, Furnaces number 1 and 7. Testing at Howco Sheffield except metallographic examination which shall be at Exova Tees-side or another lab acceptable to EMDC. F51 base material from Foroni or BGH Siegen
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
84 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Forgings 22Cr Clydesdale Forge, Hartlepool, UK
ASTM A182 F51
108 mm max 36.8 kg max. per forging
Closed die, hammer forged
Heat Treatment by Darlington Heat Treatments, Newton Aycliffe Mechanical and corrosion testing by Caparo Testing Technologies, Hartlepool, or another test house acceptable to EMDC Not pickled – items to be fully machined or pickled by others PMI and FFS by a laboratory acceptable to EMDC Base material from Valbruna (Vicenza / Bolzano) or Outokumpu (Degerfors)
13 Forgings 22Cr MEGA-Isma, Italy
ASTM 182 F51 78 mm max 24 kg max per forging
Closed die, press forged
Heat treatment according to procedure NOR001 at Sorbit furnace island F10. Testing in house; at Sigma Tre, Garbagnate Monasterio; corrosion testing by Quality Control Mediolago; or another laboratory acceptable to EMDC. Base material from Valbruna, Vicenza. Sandvik, Olarra or Cogne This qualification relates to the material quality only and does not constitute an approval of the fitting design.
13 Forgings 22Cr Hans van Triel, Essen, Germany
ASTM A182 F51
Open die 200 mm
Open die hammer forged Free formed ring forged
Base material from Aceralava, Outokumpu (Degerfors), BGH (Siegen), Bohler, Cogne. Heat Tretament in Furnace number 5 to Procedure HvT 2/2-035. PMI by others. Testing by Germanischer Lloyds, Herne or another test lab acceptable to EMDC.
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
85 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Forgings 22Cr MSI Quality Forgings, Doncaster, UK
ASTM A182 F51
200 mm
Open Die, Hammer Forged
Base material from Aceralava Mechanical testing by TEI Wakefield or another test lab acceptable to EMDC
13 Forgings 22Cr Fratelli Risetti, Solbiate Arno (VA), Italy
ASTM A182 F51
106 mm 60 kg max per forging
Closed Die, Hammer
Base material from Valbruna or Ugitech This qualification relates to the material quality only and does not constitute an approval of the fitting design.
14 Forgings 22CR WFI International, Houston Texas, USA
ASTM A182 F51
100 mm No weight restriction
Closed Die Pressed
Base material from Outokumpu, Richburg, SC, Foroni or Valbruna, Vicenza Testing in house or by Accu-Test or Exova, Houston. Heat treat in house in Furnace #s 483, 489 or 499 or by Specialty Heat Treatment Houston, Furnace #s 200, 203, 253 or 257. FFS by CDJ Services Houston This qualification relates to the material quality only and does not constitute an approval of the fitting design.
14 Forgings 22Cr Abbey Stainless, Sheffield, UK
ASTM A182 F51
200 mm No weight restriction
Open Die Hammer
MPS ASS 05-08 Base Material from Aceralava Forging by Forge UK Heat Treatment at Metal Treatment UK Furnaces # 1 and 2 Testing by Metal Testing UK Analysis by Sheffield Testing
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
86 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
10 Forgings 25Cr Fomas, Osnago,(LC), Italy
A182 F53 (UNS S32750)
t < 120 mm
Cylindrical free form forgings
14 Forgings 25Cr Inoxfucine, Montanaso, (LO), Italy
A182 F 55 (UNS S32760)
T < 120 mm No max. weight restriction
Press free forged. (Discs)
Billet from Cogne Manufacturing Procedure MS97/G
14 Forgings 25Cr Inoxfucine, Montanaso, (LO), Italy
A182 F 55 (UNS S32760)
T < 120 mm g < 225 kg
Open Die Press (Nozzles)
Billet from Cogne Manufacturing Procedure MS87/G
14 Forgings 25Cr Inoxfucine, Montanaso, (LO), Italy
A182 F 55 (UNS S32760)
T < 120 mm No max weight restriction
Free Forging Press Flat Bar
Billet from Cogne, Aceralava, Foroni Manufacturing Procedure MS144/G
14 Forgings 25Cr Inoxfucine, Montanaso, (LO), Italy
A182 F 55 (UNS S32760)
T < 120mm No max. weight restriction
Free Forging Press and Ring Rolling Rings
Billet from Cogne, Aceralava, Foroni Manufacturing Procedure MS145/G
14 Forgings 25Cr Inoxfucine, Montanaso, (LO), Italy
A182 F 55 (UNS S32760)
T < 120 mm No max weight restriction
Free Forging Press Discs
Billet from Cogne, Aceralava, Foroni Manufacturing Procedure MS146/G
14 Forgings 25Cr Rolled Alloys Technology Limited, Blackburn, UK
UNS S32760 1' 150# to 16" 900# Max Wall = 120mm
Flanges and hubs
Only sizes tested during qualification are accepted. Formerly Weir Materials
2 Forgings 25Cr Ringmill, Dubino (SO), Italy
ASTM A182 F55 (UNS S32760)
T < 120mm T < 120 mm
Open Die + Ring Rolled Closed Die
All billet from Foroni Open and Closed Die forging by press forging.
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
87 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
6 Forgings 25 Cr ASFO, Chiuppano, (VI), Italy
A182 F53 (UNS S32750)
120 mm Open die + Ring Rolled
Billet from Avesta Degerfors Metallography at Lab San Marco or another laboratory acceptable to EMDC
7 Forgings 25Cr Melesi, Cortenove, Lecco, Italy
A182 F55 (UNS S32760)
T< 120 mm T<60mm T<120 mm T< 120m T< 91m
Open Die Pressed and Ring Rolled Open Die Hammer Open Die Pressed Closed Die Hammer Closed Die Press Forged
Cogne, Acciaerie Valbruna, Bohler, Aceralava, Foroni,
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
88 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
12 Forgings 25Cr Melesi, Cortenove, Lecco, Italy
A182 F53 (UNS S32750)
T< 120 mm T<60mm T<120 mm T< 120m T< 91m
Open Die Pressed and Ring Rolled Open Die Hammer Open Die Pressed Closed Die Hammer Closed Die Press Forged
Cogne, Sandvik, Acciaerie Valbruna,
13 Forgings 25Cr Stooss Hedingen, Switzerland
A182 Gr F55 (UNS S32760)
T < 120 T < 116
Open die pressed Open die pressed and ring rolled
Billet from Foroni or Aceralava. Testing at Exova Crema, SMT Pozzo d’Adda or another laboratory acceptable to EMDC
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
89 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Forgings 25Cr Special Quality Alloys (SQA), Sheffield, UK
A182 F53 (UNS S32750) A182 F55 (UNS S32760)
T<80 mm T<120 mm
Open Die Hammer; Blanks and Rings
S32750 Billet from Sandvik. S32760 Billet from Foroni, Cogne, Scana, or BGH. Heat Treatment in Furnace No 7 at Special Steels Forging by IFA Limited Sheffield, Forge UK, Sheffield or Special Forged Products Limited, Sheffield. Testing by Special Testing Limited or another laboratory acceptable to EMDC.
8 Forgings 25Cr Bruck, Ensheim, Germany
ASTM A182 Gr F55 (UNS S32760)
T< 120 mm. Contour Forged Billet from Bohler
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
90 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
14 Forgings 25Cr Spromak, Liverpool, UK
ASTM A182 F53 (UNS S32750)
Max t = 70 mm Max weight = 46 kg
Closed Die Forged
Forging by Dyform-Jenkins-Dunn. Spromak also use fully forged and heat treated items from Abbey Forge Sheffield. Heat Treatment by Darlington Heat Treatment Heat Treatment by Darlington Heat Treatment Testing by Exova Netherton, Salford or Tees-side or another test laboratory acceptable to EMDC Material from Sandvik This qualification relates to the material quality only and does not constitute an approval of the fitting design.
14 Forgings 25Cr Spromak, Liverpool, UK
ASTM A182 F55 (UNS S32760)
Max t = 99 mm Max weight = 149 kg
Closed Die Forged
Forging by Dyform-Jenkins-Dunn. Spromak also use fully forged and heat treated items from Abbey Forge Sheffield. Heat Treatment by Darlington Heat Treatment. Heat Treatment by Darlington Heat Treatment Testing by Exova Netherton, Salford or Tees-side or another test laboratory acceptable to EMDC Material from Bohler, Valbruna, BGH Freital, Cogne, Foroni, Scana Stavanger or Aceralava. This qualification relates to the material quality only and does not constitute an approval of the fitting design.
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
91 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
12 Forgings 25Cr Forgiatura Marcora Srl, Olgiate Olona (VA) Italy
A182 F 53 (UNS S32750)
t < 125 mm No weight limit
Discs Open die forged
Heat treatment by Sorbit furnace islands F6 or F10 Base material Cogne, Valbruna, Aceria de Alava Testing by Sigmatre or another test house acceptable to EMDC
14 Forgings 25Cr Galperti s.r.l., Cortenova, Lecco, Italy
ASTM A182 F53
120 mm max No weight restriction
Closed die, press forged; Closed die press forged and ring rolled
Heat treatment in furnace H2 and in tank number HTT2 Testing by AQM, Sigmatre or another laboratory acceptable to EMDC. Base material from Cogne or Sandvik
13 Forgings 25Cr Galperti s.r.l., Cortenova, Lecco, Italy
ASTM A182 F55
120 mm max No weight restriction
Closed die, press forged; Closed die press forged and ring rolled
Heat treatment in furnace H2 and in tank number HTT2 Testing by AQM, Sigmatre or another laboratory acceptable to EMDC. Base material from Foroni
13 Forgings 25Cr Hans van Triel, Essen, Germany
ASTM A 182 F53
Open Die 120 mm
Open die hammer forged Free formed ring forged
Base material Heat treatment in Furnace number 5 to procedure HvT 2/2-030. PMI by others. Testing by Germanischer Lloyds, Herne or another test lab acceptable to EMDC.
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
92 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Forgings 25Cr Hans van Triel, Essen, Germany
ASTM A182 F55
Open Die 120 mm
Open die hammer forged Free formed ring forged
Base material from Heat treatment in Furnace number 5 to procedure HvT 2/2-027. PMI by others. Testing by Germanischer Lloyds, Herne or another test lab acceptable to EMDC.
13 Forgings 25Cr MEGA-Isma, Italy
ASTM 182 F53 78 mm max 17 kg max per forging
Closed die, press forged
Heat treatment according to procedure NOR001 at Sorbit furnace island F10. Testing in house; at Sigma Tre, Garbagnate Monasterio; corrosion testing by Quality Control Mediolago; or another laboratory acceptable to EMDC. Base material from Sandvik, Sandviken. This qualification relates to the material quality only and does not constitute an approval of the fitting design.
13 Forgings 25Cr MEGA-Isma, Italy
ASTM 182 F55 78 mm max 17 kg max per forging
Closed die, press forged
Heat treatment according to procedure NOR001 at Sorbit furnace island F10. Testing in house; at Sigma Tre, Garbagnate Monasterio; corrosion testing by Quality Control Mediolago; or another laboratory acceptable to EMDC. Base material from BGH Freital. This qualification relates to the material quality only and does not constitute an approval of the fitting design.
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
93 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Forgings
25Cr
Howco Quality Alloys / Howco Metals Management, Sheffield,
ASTM A182 F55
IFA Route 100 mm Forge UK Route 120 mm
Pressed and / or Hammer Forged
Heat treatment in Howco Sheffield, Furnaces number 1 and 7. Testing at Howco Sheffield except metallographic examination which shall be at Exova Tees-side or another lab acceptable to EMDC. Base Material from Foroni or BGH Siegen
13 Forgings 25Cr MSI Quality Forgings, Doncaster, UK
ASTM A182 F55
120 mm Open Die, Hammer Forged
Base material from Scana Stavanger Mechanical testing by TEI Wakefield or another test lab acceptable to EMDC
13 Forgings 25Cr SBP Metals Technology, Sheffield, UK
ASTM A182 F55
120 mm Open Die Press and Hammer Forged
Forging by Forge UK (Production Route AG F002) Heat treatment by QHT Rotherham, Furnace number 1. Testing at MTT Sheffield Base Material from Scana Stavanger
13 Forgings 25Cr Fratelli Risetti, Solbiate Arno (VA), Italy
ASTM A182 F53
80 mm 64 kg max per forging
Closed Die, Hammer
Base material from Sandvik, Sweden This qualification relates to the material quality only and does not constitute an approval of the fitting design.
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
94 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Forgings 25Cr Fratelli Risetti, Solbiate Arno (VA), Italy
ASTM A182 F55
80 mm 64 kg max per forging
Closed Die, Hammer
Base material from Valbruna or BGH Freital This qualification relates to the material quality only and does not constitute an approval of the fitting design.
14 Forgings 25CR WFI International, Houston Texas, USA
ASTM A182 F55
76 mm No weight restriction
Closed Die Pressed
Base material from Rolled Alloys Technology, Blackburn, UK; BGH Siegen, Germany Testing in house or by Accu-Test or Exova, Houston. Heat treat in house in Furnace #s 483, 498 or 499 or by Specialty heat Treatment Houston, Furnace #s 200, 203, 253 or 257. FFS by CDJ Services Houston This qualification relates to the material quality only and does not constitute an approval of the fitting design.
14 Forgings 25Cr Abbey Stainless, Sheffield, UK
ASTM A182 F55
120 mm No weight restriction
Open Die Hammer
MPS ASS 06-08 Base Material from Scana Stavanger Forging by Forge UK Heat Treatment at Metal Treatment UK Furnaces # 1 and 2 Testing by Metal Testing UK Analysis by Sheffield Testing
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
95 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Induction Bends
22Cr Proclad - IBS, Glenrothes, UK
UNS S31803 Not applicable; test bend to be run as per MPDS 29-01-07
Induction bent pipe, seamless and welded
Heat treatment:- internal (using Furnaces 1, 2 or 3 at Glenrothes) or by ConMech, Consett, Co.Durham, Testing by M.I.S. Livingston or Consett, Co.Durham, or another laboratory acceptable to EMDC PPM required for each PO; Materials Group shall be in attendance
14 Induction Bends
25Cr Proclad - IBS, Glenrothes, UK
UNS S32760 Not applicable; test bend to be run as per MPDS 29-01-07
Induction bent pipe, seamless and welded
Heat treatment:- internal (using Furnaces 1, 2 or 3 at Glenrothes) or by ConMech, Consett, Co.Durham, Testing by M.I.S. Livingston or Consett, Co.Durham, or another laboratory acceptable to EMDC PPM required for each PO; Materials Group shall be in attendance
13 Induction Bends
22Cr Induction Pipe Bending (IPB), Sunderland, UK
UNS S31803 Not applicable; test bend to be run as per MPDS 29-01-07
Induction bent pipe, seamless and welded
Heat treatment by Conmech, Co Durham Testing in-house or at another lab acceptable to EMDC. PPM required for each PO; Materials Group shall be in attendance
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
96 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Induction Bends
25Cr Induction Pipe Bending (IPB), Sunderland, UK
UNS S32760 Not applicable; test bend to be run as per MPDS 29-01-07
Induction bent pipe, seamless and welded
Heat treatment by Conmech, Co Durham Testing in-house or at another lab acceptable to EMDC. PPM required for each PO; Materials Group shall be in attendance
13 Induction Bends
22Cr SIMAS, Prezzate-Mapello, Italy
UNS S31803 Not applicable; test bend to be run as per MPDS 29-01-07
Induction bent pipe, seamless and welded pipe
Testing by SMT, Pozzo d’Adda, or another laboratory suitable to EMDC PPM required for each PO; Materials Group shall be in attendance
13 Induction Bends
25Cr SIMAS, Prezzate-Mapello, Italy
UNS S32750 Not applicable; test bend to be run as per MPDS 29-01-07
Induction bent pipe, seamless and welded pipe
Testing by SMT, Pozzo d’Adda, or another laboratory suitable to EMDC PPM required for each PO; Materials Group shall be in attendance
14 Induction Bends
22Cr Fabricom, Grimbergen, Belgium
UNS S31803 Not applicable; test bend to be run as per MPDS 29-01-07
Induction bent pipe, seamless and welded
Testing by Stork Intermes, Berchem, or at another lab acceptable to EMDC. PPM required for each PO; Materials Group shall be in attendance
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
97 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
14 Induction Bends
25Cr Fabricom, Grimbergen, Belgium
UNS S32760 Not applicable; test bend to be run as per MPDS 29-01-07
Induction bent pipe, seamless and welded
Testing by Stork Intermes, Berchem, or at another lab acceptable to EMDC. PPM required for each PO; Materials Group shall be in attendance
0 Plate 22Cr Outokumpu, Hot Rolled Plate Division - Degerfors, Sweden
A240 S31803 t = 6 - 50 mm Hot rolled plates
Heat treatment in batch furnace: "Norm-ugn". Formerly Avesta Polarit AB, Hot Rolled Plate Division
7 Plate 22Cr Outokumpu, KBR Mill, Avesta, Sweden
A240 S31803 3.00 to 13.00 mm Hot Rolled Forced Air Cooled Formerly Avesta Polarit
7 Plate 22Cr Outokumpu, KBR Mill, Avesta, Sweden
A240 S31803 1.50 - 6.35 mm
Cold Rolled Forced Air Cooled Formerly Avesta Polarit
14 Plate 22Cr Bohler Bleche, Murzzuschlag, Austria
A240 S31803 / S32205
1.50 – 76.2 mm Hot Rolled MPS FPP01/2010 Rev 00 Slab from Bohler Edestahl Kapfenberg G48 and Fischer Ferritescope by Bohler Edelstahl, Kapfenberg Final heat treatment in furnace Neuss # 4121
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
98 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
7 Plate 25Cr Outokumpu, KBR Mill, Avesta, Sweden
A240 S32750 1.50 - 6.35 mm Cold Rolled Water Quenched Formerly Avesta Polarit
14 Plate 25Cr Duplex
Rolled Alloys Technology, Blackburn, UK
UNS S32760 1.5 – 92 mm thick Formerly Weir Materials
14 Plate 25Cr Bohler Bleche, Murzzuschlag, Austria
A240 S32750 1.50 – 50.0 mm Hot Rolled MPS FPP 03/2010 Rev 00 Slab from Bohler Edestahl Kapfenberg G48 and Fischer Ferritescope by Bohler Edelstahl, Kapfenberg Final heat treatment in furnace Neuss # 4121
14 Plate 25Cr Bohler Bleche, Murzzuschlag, Austria
A240 S32760 1.50 – 50.0 mm Hot Rolled MPS FPP 02/2010 Rev 00 Slab from Bohler Edestahl Kapfenberg G48 and Fischer Ferritescope by Bohler Edelstahl, Kapfenberg Final heat treatment in furnace Neuss # 4121
13 Seamless Pipe
22Cr SMST France Montbard, France
A790 S31803 t < = 20.6 mm NPS<=8"
Direct hot extrusion
Base material from SMTS Germany in Remscheid and from Montbard in France Formerly DMV Montbard
13 Seamless Pipe
22Cr SMTS Italy, Costa Volpino, (BG), Italy
A790 UNS S31803
Up to 5 mm thick, NPS<=2"
Cold Pilgered Base material from SMTS Germany in Remscheid and from Montbard in France Formerly DMV Costa Volpino
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
99 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
10 Seamless Pipe
22Cr Sandvik Steel, Sandviken, Sweden
A790 UNS S31803
Hot Finished <= 22.83 mm th. Cold Finished <= 10.23 mm th.
All material to be water quenched. Sandviken Plant, Sweden
10 Seamless Pipe
22Cr Schoeller Bleckmann, Ternitz, Austria
A790 UNS S31803
Max t = 22.83 mm MaxOD = 168.28 mm Max t = 12.5 mm Max OD = 88.9 mm Max t = 15.63 Max OD = 104.00
Production Route 1 (Hot and Cold Formed) Production Route 2 (Cold Pilgered) Production Route 3 (Cold Drawn)
Base material from Tubacex Spain
11 Seamless Pipe
22Cr Tubacex Tubos Inoxidables, Llodio, Spain
ASTM A 789 UNS S31803 ASTM A790 UNS S31803
Route 1: 31.75 mm max Route 2: 15.88 mm max Max OD = 8 inch
See Mandatory subcontractors & conditions
Route 1: Hot finished, direct water quenching Route 2: Hot finished, continuous furnace heat treatment. Base Material from Aceralava
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
100 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
2 Seamless Pipe
22Cr Wyman Gordon, Livingston, UK
A790 S31803 12 < t < 94 mm 200 < OD < 900 mm
Extruded Pipe Note pipe of wall thickness up to 160 mm may be produced. See report for qualification status of this material.
6 Seamless Pipe
22Cr Sumitomo, Amagasaki Mill, Japan
A790 S31803 Up to 7" OD Up to 17.8 mm thick
Hot Extruded Pipe
6 Seamless Pipe
22Cr Sumitomo, Wakayama Mill, Japan
A790 S31803 Up to 7 to 12" OD Up to 26.7 mm thick
Hot forging / rolling / piercing (Mannesman Process)
6 Seamless Pipe
22Cr IBF, Vittuone, (MI) Italy
A790 S31803 18 - 36 mm thick 4 - 24" OD
Seamless Pipe (from hot forged bar to A182)
Process Route 6 Base material from Foroni Heat treatment furnace No 8 (Calibrated in accordance with API 610 Appx. H.)
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
101 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
10 Seamless Pipe
25Cr Schoeller Bleckmann, Ternitz, Austria
A790 UNS S32760
Max t = 22.83 mm MaxOD = 168.28 mm Max t = 12.5 mm Max OD = 88.9 mm Max t = 15.63 Max OD = 104.00
Production Route 4 (Hot and Cold Formed) Production Route 5 (Cold Pilgered) Production Route 6 (Cold Drawn)
Base material from Tubacex Spain
13 Seamless Pipe
25Cr SMST France Montbard, France
A790 UNS S32760
t < = 20.6 mm NPS<=8"
Direct hot extrusion
Base material from SMTS Germany in Remscheid and from Montbard in France Formerly DMV Montbard
13 Seamless Pipe
25Cr SMTS Italy, Costa Volpino, (BG), Italy
A790 UNS S32760
Up to 7.9 mm thick, NPS<=2"
Cold Pilgered Base Material from SMTS France in Montbard Fornerly DMV Costa Volpino
14 Seamless Pipe
25Cr Rolled Alloys Technology Limited, Blackburn, UK
A790 S32760 2.77 - 21.95 No weight restriction
Formerly Weir Materials
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
102 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
10 Seamless Pipe
25Cr Sandvik, Sandviken, Sweden
A790 S32750 Hot Finished <= 13.71 mm th. Cold Finished <= 10.23 mm th.
All material to be water quenched. Sandviken Plant, Sweden
6 Seamless Pipe
25Cr IBF Seamless Pipes, Vittuone (MI) Italy
UNS S32760 14 - 27 mm thick 4 - 24" OD
Seamless Pipe (from hot forged bar to A182)
Process Route 6 Base material from Foroni Heat treatment furnace No 8 (Calibrated in accordance with API 610 Appx H.)
10 Seamless Pipe
25Cr Tubacex Tubos Inoxidables, Llodio, Spain
ASTM A 789 UNS S32760 ASTM A790 UNS S32760
Route 1: 22.83 mm max Route 2: 13.91 mm max Route 3: 10.93 mm max Max OD = 8 inch
See Mandatory subcontractors & conditions
Route 1: Hot finished, direct water quenching Route 2: Hot finished, continuous furnace heat treatment. Route 3: Cold finished, continuous furnace heat treatment. Base Material from Aceralava
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
103 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
14 Seamless Pipe
25Cr Tubacex Tubos Inoxidables, Llodio, Spain
ASTM A 789 UNS S32750 ASTM A790 UNS S32750
Route 1: 27.44 mm max Route 2: 19.05 mm max Route 3: 8.93 mm max Max OD = 8 inch
See Mandatory subcontractors & conditions
Route 1: Hot finished, direct water quenching Route 2: Hot finished, continuous furnace heat treatment. Route 3: Cold finished, continuous furnace heat treatment. Base Material from Aceralava
5 Semi Finished Billet
22Cr Valbruna Acciaierie, Vicenza and Bolzano, Italy
UNS S31803 Not Applicable
Semi finished billet for re-processing by others
5 Semi Finished Billet
25Cr Valbruna Acciaierie, Vicenza and Bolzano, Italy
UNS S32760 Not Applicable Semi finished billet for re-processing by others
10 Welded Pipe (LSW)
22Cr Outokumpu, Fagerstad, Sweden
A928 UNS S31803
2-4" Sch10S Formerly AST (Avesta)
10 Welded Pipe (LSW)
22Cr Outokumpu, Storfors, Sweden
A928 UNS S31803
Cl 1, 25 mm max, Cl 3, 7.12 mm max, Max Dia = 610 mm
Formerly AST (Avesta) Heat treatment in roller hearth furnace only. Plate from Outokumpu Degerfors or Avesta
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
104 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
8 Welded Pipe (LSW)
22Cr Butting, Knesebeck, Germany
A928 S31803
2 - 36" 1.6 - 50 mm
Plate from Avesta KBR, Avesta Degerfors, Thyssen Krupp Nirosta, Industeel Arcelor (Fabrique de Fer), Industeel Arcelor (Le Creusot)
7 Welded Pipe (LSW)
22Cr Erndtebrucker Eisenwerke (EEW), Erndtebruck, Nr Siegen, Germany
A928 UNS S31803
8mm wt to 28 mm wt 6 - 60" OD
Welded Pipe The level of cold work after solution annealing to be restricted to 1% maximum. Testing by sub contract laboratory acceptable to EMDC. Plate from Avesta Degerfors or Fabrique de Fer Heat treatment by EEW or by Schulz in Krefeld, Germany.
14 Welded Pipe (LSW)
22Cr InoxTech Lendinara, Italy
A928 UNS S31803
t = 10 - 60 mm Welded Pipe Heat Treatment in Furnace H Base materials from, Outukumpu (Degerfors), Thyssen Krupp, Industeel (Le Creusot and Fabrique de Fer) All repair welds shall be solution annealed
14 Welded Pipe (LSW)
25Cr Rolled Alloys Technology Limited, Blackburn, UK
A928 S32760 NPS 6 - 30" Wall Thickness 3.76 - 31.75
Formerly Weir Materials
8 Welded Pipe (LSW)
25Cr Butting, Knesebeck, Germany
A928 S32760 8 - 36" 2.7 - 44 mm
Plate from, Avesta KBR, Avesta Degerfors, Thyssen Krupp Nirosta, Bohler.
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
105 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
10 Welded Pipe (LSW)
25Cr Outokumpu, Storfors, Sweden
A928 UNS S32750
Cl 1, 18.75 mm max, Cl 3, 5.71 mm max Max Dia = 610 mm
Formerly AST (Avesta) Heat treatment in roller hearth furnace only. Plate from Outokumpu Degerfors or Avesta
14 Welded Pipe (LSW)
25Cr InoxTech Lendinara, Italy
A928 UNS S32750
t = 10 – 40 mm Welded Pipe Heat Treatment in Furnace H Base materials from, Outokumpu (Degerfors), Thyssen Krupp, Industeel (Le Creusot and Fabrique de Fer) All repair welds shall be solution annealed
14 Welded Pipe (LSW)
25Cr InoxTech Lendinara, Italy
A928 UNS S32760
T = 6 – 32 mm Welded Pipe Heat Treatment in Furnace H Base materials from, Outokumpu (Degerfors), Thyssen Krupp, Industeel (Le Creusot and Fabrique de Fer) All repair welds shall be solution annealed
13 Umbilical Tubing
25Cr Sandvik Precision Tubes, Chumotov, Czech Republic
A789 S32750 1.00 < t < 4.93 mm 11.0 < OD < 46.00 mm
Extruded Seamless Tube
Hall 1 Heat Treatment in RODR 1000 Furnace Line Base material originally melted in Sandvik Sweden (Sandviken). Extruded Hollows from Sandvik Sweden, Sandvik India (Rajpur) and Sandvik, Scranton USA (Scranton)
13 Umbilical Tubing
25Cr Sandvik Precision Tubes, Chumotov, Czech Republic
A789 S32750 1.00 < t < 5.00 mm 11.0 < OD < 31.10 mm
Extruded Seamless Tube
Hall 1 Heat Treatment in RODR 2000 Furnace Line Base material originally melted in Sandvik Sweden (Sandviken). Extruded Hollows from Sandvik Sweden, Sandvik India (Rajpur) and Sandvik, Scranton USA (Scranton)
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
106 of 114
Added / Updated Rev No.
Product Form (See Note 7)
Type of Material
Manufacturer
Standard and Grade
Qualified thick- ness/weight
Material form
Mandatory subcontractors & conditions
13 Umbilical Tubing
25Cr Sandvik Precision Tubes, Chumotov, Czech Republic
A789 S32750 1.00 < t < 2.68 mm 11.0 < OD < 30.00 mm
Extruded Seamless Tube
Hall 2 Heat Treatment in Drever Furnace Line Base material originally melted in Sandvik Sweden (Sandviken). Extruded Hollows from Sandvik Sweden, Sandvik India (Rajpur) and Sandvik, Scranton USA (Scranton)
10 Umbilical Tubing
25Cr Sandvik, Sandviken Sweden
A789 S32750 2.90 < t , 6,6 mm 50 < OD < 108.5 mm
Extruded Seamless Tubes
Centre Tubing Only Heat Treatment in Furnace USAB 326 RV63 Pickled finish
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
107 of 114
Qualified Independent Test Laboratories The laboratories on this list have been qualified to carry out the testing required by MPDS 29-01-02. For testing outside the scope of this specification please contact EMDC Materials.
Added /
Updated
Rev #
Laboratory Name Location and Contact Details Notes
14 Accu-Test 7821 Pinemont, Houston, TX, 77040, USA
+1 713 460 3655
www.accutest-labs.com
14 AQM Via Edison 18, 25050 Provaglio d’Iseo, (Brescia), Italy
+39 030 9291711
www.aqm.it
14 CoMech Castings Road, Derby, DE23 8LY, UK
+44 1332 867 700
www.comech.co.uk
14 Exova Edinburgh, UK Lochend Induxctrial Estate, Newbridge, EH28 8PL, UK
+44 131 333 4360
www.exova.com
Formerly Bodycote
14 Exova Houston, USA 9925 Regal Row, Houston, TX, 77040, USA
+1 281 848 0270
www.exova.com
Formerly Bodycote
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
108 of 114
14 Exova, Crema, Italy Via dalla Pierina 9/11, Crema, (CR), Italy
+39 0373 89721
www.exova.com
Formerly Bodycote
14 Exova Karlskpga, Sweden Gammelbackavägen 6, Box 431, Karlskoga, 691 27
+46 (0)586 810 55
www.exova.com
Formerly Bodycote
14 Exova Dudley, UK 182 Halesowen Road, Netherton, West Midlands, UK
+44 1384 455 751
www.exova.com
Formerly Bodycote
14 Exova Tees-side, UK Holwick Road, Riverside Park, Cleveland, TS2 1QS, UK
+44 1642 250 336
www.exova.com
Formerly Bodycote
14 Exova Bridgewater, UK No 1, Festival Units, The Showground Business Park, Bridgewater, TA6 6LS, UK
+44 1278 456 888
Formerly Bodycote
14 Exova Sandnes, Norway Luramyrveien 69, PO Box 1084, Sandnes, Norway
+47 51 709 690
Formerly Bodycote
14 Germanischer Lloyds, Germany Südstraße 59, 44625 Herne, Germany
+49 02325 637969-0
www.gl-nobledenton.com/en/Herne.php
14 Metals Testing UK Beeley Wood Lane
+44 114 231 8805
www.theabbeygroupuk.co.uk
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
109 of 114
14 M.I.S. Consett, UK Eden House, Watling Street industrial Estate, Leadgate, Co Durham, DH8 6TA,
UK+44 1207 599 260
www.mistesting.co.uk
14 M.I.S. Livingston, UK Unit 5a, Telford Square Business Park, Houston Industrial Estate, Houston Road,
Livingston, EH10 5PQ, UK
+44 1506 432 203
www.mistesting.com
14 M.T.T. Sheffield, UK Metals Technology Testing Ltd, Finchwell Close, Sheffield, S13 9D, UK
+44 114 243 7271
www.metalstechnology.co.uk
14 SigmaTre, Italy Via Fornace 31, 23846 Garbagnate Monasterio, (Lecco), Italy
+39 031 87 94 25
www.sigmatre.it
14 S.M.T. Italy Via del Lavoro 7, 20060 Pozzo d’Adda, (Mi), Italy
+39 02 909 67 142
www.smtsrl.com
14 Special Testing Limited, UK Bacon Lane, S9 3NH, UK
+44 114 244 1061
www.specialtesting.co.uk
14 St. Louis Testing Laboratory, USA 2810 Clark Avenue, St. Louis, MO, 63103, USA
+1 314 531 8080
www.labinc.com
Duplex Stainless Steel Manufacturers EMDC List of Qualified Suppliers
Suppliers are qualified in accordance with MPDS 29-01-04 to supply material in accordance with MPDS 29-01-02 Revision 14 – 2011
110 of 114
14 T.E.I. Ltd. UK Po Box 80, Calder Vale Road, Wakefield, West Yorkshire, WF1 5YS, Wakefield,
UK
+44 1924 780000
www.tei.co.uk/metallurgical-laboratory.php
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 111 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
22. Upstream Acceptable Manufacturers of Structural Plate, Shape and Tubular Products
Refer to TS 29-01-09: Upstream Acceptable Manufacturers of Structural Plate, Shape and
Tubular Products.
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 112 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Record of Change
Rev 1 Date: Apr
2011
Location Action Description
Section 6 Addition Added the following manufacturers in Unfired Pressure Vessel category:
- Petra Fabricators - Jutasama - AMC
Section 9 Deletion Deleted Dalmine from the Low Chrome up to 13% and Alloy, SS, Monel
and etc category as it is not approved in the EMDC QSL list
Section 17 Deletion Deleted Perwaja Steel Sdn Bhd from Structural & Architectural – Steel
Plates
Section 20 Addition Addition of Section 20 - Qualified Forging List
Section 21 Addition Addition of Section 21 - Qualified Suppliers List for Duplex Stainless
Steel
Section 22 Addition Addition of Section 22 - Acceptable Manufacturers of Structural Plate,
Shape and Tubular Products)
Rev 0 Date: Nov
2010
Location Action Description
Initial Publish.
Instituted Purpose Codes [X], [Y], [Z] to identify those paragraphs that
have been deleted ( [X] ), modified ( [Y] ), or added ( [Z] ) as a result of
the Gap Analysis undertaken to identify items in heritage EMEPMI
design documentation (DIM and GS) and other sources relevant to
EMEPMI operations (i.e. Regulatory requirements) that should be
included into the MPDS.
Those paragraphs with Purpose Codes [X], [Y], [Z] shall be compared
against subsequent revisions of the GPs as they are accepted into
EMEPMI.
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 113 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Attachment: Purpose Codes Definitions
Code Description
C Assigned to paragraphs containing specifications whose primary purpose is reduced costs.
Reduced cost in this context refers to initial investment cost and does not include Life-Cycle
cost considerations. Life-Cycle cost considerations are captured under reliability,
maintainability, or operability purpose codes.
E Assigned to paragraphs containing specifications whose primary purpose is driven by
environmental considerations. Environmental considerations typically include specifications
intended to protect against emissions/leakage to the air, water, and/or soil. Deviations from the
specifications contained in such paragraphs require formal review and approval according to
local environmental policy.
I Assigned to paragraphs that provide only clarifying information such as Scope statements,
definitions of terms, etc.
M Assigned to paragraphs containing specifications whose primary purpose is to provide for
maintainability of equipment or systems. Maintainability provisions are those that facilitate the
performance of maintenance on equipment/systems either during downtimes or during on-
stream operations.
O Assigned to paragraphs containing specifications whose primary purpose is to assure
operability of equipment or systems. Operability is the ability of the equipment/system to
perform satisfactorily even though conditions are off-design, such as during start-ups, process
swings, subcomponent malfunction, etc.
R Assigned to paragraphs containing specifications whose primary purpose is to improve or
assure the reliability of equipment or systems. Reliability is a measure of the ability of
equipment/systems to operate without malfunction or failure between planned maintenance
interventions.
S Assigned to paragraphs containing specifications whose primary purpose is avoidance of
personnel or operational safety incidents. Any deviation from the specifications contained in
such designated paragraphs requires formal review and approval according to local safety
policy.
Personnel Safety: Refers to the avoidance of recordable personnel injuries; i.e., burns, cuts,
abrasions, inhalation, or exposure to dangerous substances, etc., that
could result in medical treatment, restricted work, lost-time incidents, or
fatalities.
Operational
Safety:
Refers to the prevention and control of process releases, fires, explosions,
etc.
MPDS 00-99-01 Equipment and Materials Source List
Malaysian Project Design Specification April 2011
Upstream MPDS 00-99-01 REV 1
Page 114 of 114
EXXONMOBIL EXPLORATION & PRODUCTION MALAYSIA INC.
Code Description
X Assigned to paragraphs that have been deleted in their entirety from the GP base-document,
and not replaced when developing the MPDS. The associated Rationale content has been
deleted as appropriate. The statement “Intentionally Deleted” has been added to the original
GP item number to retain the GP base-document structure.
The GP base-document and revision are listed on the front page of this MPDS as well as all
page footers.
The deleted paragraphs and requirements therein were not applicable to the MPDS at the time
of MPDS development. Subsequent revisions of the GP shall be compared against this
MPDS to ensure that GP updates are properly incorporated into the next revision of the
MPDS, including a review of deleted paragraphs to ensure the deletion is still valid.
Y Assigned to paragraphs that have been modified from the GP base-document when developing
the MPDS. These modifications may include partial deletion of text from a specific
requirement. The changes identified are of a technical nature, affecting the clause of the
MPDS (compared to the GP base-document). Clerical changes, such as replacement of "GP"
with "MPDS" or "Company" with "EMEPMI" are not identified.
The GP base-document and revision are listed on the front page of this MPDS as well as all
page footers.
Specific project requirements have been written into the GP base-document paragraph.
Subsequent revisions of the GP shall be compared against this MPDS to ensure that GP
updates are properly incorporated into the next revision of the MPDS. The specific project
requirements embedded in the GP base-document paragraphs shall be retained in subsequent
revisions of the MPDS unless otherwise superseded by requirements in the GP. Alternately,
they may be removed via the appropriate deviation process.
Z Assigned to paragraphs that have been added to the GP base-document.
The GP base-document and revision are listed on the front page of this MPDS as well as all
page footers.
The paragraph numbers assigned shall add onto the GP base-document structure. Therefore,
subsequent revisions of the GP shall be compared against this MPDS to ensure that GP updates
are properly incorporated into the next revision of the MPDS. All additional paragraphs in this
MPDS shall be included in subsequent revisions of the MPDS unless otherwise superseded by
requirements in the GP. Alternately, they may be removed via the appropriate deviation
process.