Doc# E166719 V.1.01 QS - 1

MDLN/MDSN Display Quickstart Guide

Electro Industries/GaugeTechThe Leader In Power Monitoring and Smart Grid SolutionsElectro Industries/GaugeTechThe Leader In Power Monitoring and Smart Grid Solutions

MDLN/MDSN Display Quickstart Guide Contents of Display Kit

Display Dimensions

7 6 5 4

3 2 1 (1) Display

(2) Rear Module

(3) Power Supply

(4) RS485 Serial Cable (10 ft)

Mounting Hardware:

(5) anti-rotation tee

(6) socket wrench

(7) installation nut, attached to

the back of the display

[1.18in]30mm3.43mm

0.13in

[0.2

6in]

6.7m

m

[0.63in]16.2mm

[0.60in]15.3mm

[1.24in]31.5mm

[2.85in]72.6mm

[3.84in]97.6mm

[2.1

6in]

55m

m

[3.1

4in]

80m

m

0.22

mm

0.86

in

MDSN Dimensions

Doc# E166719 V.1.01 QS - 2

MDLN/MDSN Display Quickstart Guide

Electro Industries/GaugeTechThe Leader In Power Monitoring and Smart Grid SolutionsElectro Industries/GaugeTechThe Leader In Power Monitoring and Smart Grid Solutions

[1.20in]30.6mm

[1.57in]40.1mm

[4.64in]118mm

[3 .8

6in]

98.1

mm

[ 0.6

7in]

17.2

mm

[0.37in]9.5mm

[6.41in]163mm

[4.63in]117.7mm

[3.4

8in]

88.4

mm

[5.0

9in]

129.

4mm

22.1

mm

0.87

in[0.60in]15.3mm

[0.69in]17.5mm

[1.29in]32.8mm

[1.18in]30mm3.43mm

0.13in

[0.2

6in]

6.7m

m

MDLN Dimensions

MDSN/MDLN Back Dimensions

Doc# E166719 V.1.01 QS - 3

MDLN/MDSN Display Quickstart Guide

Electro Industries/GaugeTechThe Leader In Power Monitoring and Smart Grid SolutionsElectro Industries/GaugeTechThe Leader In Power Monitoring and Smart Grid Solutions

Mechanical Installation: Mount the unit in an enclosure that provides a clean, dry, and controlled environment (IP65f enclosure or UL508 4x, if indoors). 1. Create a panel cutout based on the charts below, and install the display from the front. You can use the tee insert to stop display rotation when you apply torque during installation. With the tee option, the rotating torque is 6Nm/53.10 in-lb. Without the tee option the rotating torque is 2.5Nm/ 22.12 in-lb.

Without Tee

With Tee

2. Insert the display module

(along with the tee insert if

you are using it) into the

panel hole.

3. Screw the nut using the

socket wrench with a

torque between 1.2 and

2 Nm/10.62 and 17.70

in-lb.

4. Insert and push the rear

module until it locks into

place.

Unit A (mm) A (in.) B (mm) (1)

B (in.) (1)

B (mm) (2)

B (in.) (2)

MDSNMDLN

+022.50

-0.30

+00.88

-0.011.5 to 6

0.06 to 0.23

3 to 6 0.11 to 0.23

The Material of the panel(1) Steel sheet (2) Fiberglass (minimum GF30)

Unit C (mm) C (in.) D (mm) (1)

D (in.) (1)

MDSNMDLN

+030.00

-0.20

+01.18

-0.007

+04.00

-0.20

+0.15

-0.007

A

B

D

C

1

2 3

4

5Insert andpush

Free Locked

1: Display Module (front)2: Panel with Cutout3: Display Installation Nut4: Anti-Rotation Tee5. Wrench

IMPORTANT! For further display details and safety considerations, refer to the MP200 Metering System Installation and Operation Manual.

NOTE: To remove the rear module, press the yellow button on the top of the display to unlock it and pull the rear module away from the display module.

Doc# E166719 V.1.01 QS - 4

MDLN/MDSN Display Quickstart Guide

Electro Industries/GaugeTechThe Leader In Power Monitoring and Smart Grid SolutionsElectro Industries/GaugeTechThe Leader In Power Monitoring and Smart Grid Solutions

Communicating with the MP200 Metering System: You can connect to the MP200 metering

system through either the Com 3 RS485 port or the optional Com 1 RJ45 Ethernet port. The display

automatically detects the connection in use. Note that both the MP200 unit and the display need to

have specific settings to enable communication between them. The display is pre-programmed to

communicate with the MP200 metering system’s default IP address and RS485 Com port settings.

NOTE: If you have changed the MP 200 unit’s IP address or if you receive a communication error

message, follow the instructions in Chapter 10 of the MP200 Metering System Installation and

Operation Manual.

To connect via RS485, use the RS485 serial

cable to connect from the RS485 port on the

display to the MP200 unit’s Com 3.

To connect via Ethernet, use an Ethernet cable

to connect from the display’s RJ45 port to the

MP200 unit’s Com 1 RJ45 port. Also, be sure

the Com 1 Switch is set to Ethernet/WiFi.

While the MP200 unit and the display

are beginning to communicate, you will

see the screen on the right. Next you

will see a screen with basic information

concerning the MP200 unit, and then

you will see one of the other two

screens (depending on whether you are

connected to an MP200-Y with 8 three

phase circuits, or an MP200-S with 24

single phase circuits). Touch a meter

number to begin viewing the screens

for the meter. See the MP200 Metering

System Installation and Operation Man-

ual for details on the available screens.

RS485 Port RJ45 Port

Com 1 SwitchFront of MP200 Unit

Bottom of Display