MP08V Receiver User Manual - DanfossSERIE PARALELO conexión externa STOP +IN STOP +OUT alimentación salidas digitales CM NO 1-8 NO A1 B6 STOP1 STOP2 CM B10 Vdc GND B B B B 12 2 11

User Manual

Remote ControlMP08V Receiver

www.danfoss.com

http://www.danfoss.com

Revision history Table of revisions

Date Changed Rev

August 2020 Corrections made to Pinout table on page 10 0102

January 2019 Rebranded to Danfoss Power Solutions 0101

User ManualMP08V Receiver

2 | © Danfoss | August 2020 BC292480424603en-000102

Safety instructionsGeneral safety.................................................................................................................................................................................... 4Safety warnings.................................................................................................................................................................................4

Technical descriptionDimensions and identification.....................................................................................................................................................6

InstallationReceiver installation........................................................................................................................................................................ 7Input and output configuration..................................................................................................................................................8

Digital outputs............................................................................................................................................................................. 8Analog outputs............................................................................................................................................................................ 8MP08V stop category 3 PLd.....................................................................................................................................................8Pinout............................................................................................................................................................................................10

TroubleshootingReceiver troubleshooting........................................................................................................................................................... 11


Contents

© Danfoss | August 2020 BC292480424603en-000102 | 3

MP08V General Safety

The following safety instructions must be read carefully to install and use the product properly, and tokeep it in perfect working condition, and to reduce the risk of misuse.• Strictly adhere to the installation instructions contained in this document.• Make sure that professional and competent personnel carry out the installation.• Ensure that all site and prevailing safety regulations are fully respected.• Make sure that this document is permanently available to the operator and maintenance personnel.• Keep the transmitter out of reach of non-authorized personnel.• Remove the transmission key when the set is not in use.• Check each working day the STOP button and other safety measures. When in doubt, press the STOP

button.• Whenever several sets have been installed, make sure the transmitter is the right one. Identify the

machine controlled on the label for this purpose on the transmitter or by using the display (in case ithas one).

• Service the equipment periodically.• When carrying out repairs, use spare parts supplied by Danfoss only.

W Warning

Potential damage to the operator or the product. Do not use this product on machines in potentiallyexplosive atmospheres unless the model is ATEX/RATEX certified to work in such conditions.

MP08V Safety Warnings

Potential damage to operator and product.Follow the guidelines below to reduce risk of injury to the operator and the product.

• Use the device with the manufacturer's battery and battery charger (if applicable).• Only allow qualified personnel to operate the equipment.• Always set the STOP button in the off position when not in use.• Always press STOP before plugging in tether cable (if applicable).• Do not operate product when visibility is limited.• Make sure product is compatible with the machine.• Avoid knocking or dropping the product.• Do not use the product if a failure is detected.

Changes or modifications not approved by Danfoss can void the user's authority to operate this product.


Safety instructions


Quick reference precautions


Safety instructions


MP08V dimensions and identification

Dimensions in mm

A B

1

2

3

4

5

6

6

7

8

35.99

29.2092.25

101.60

R 3.70

133.

03

15.7

5

42.2

7

118.73

R 3.70

1. Fixing slots (fixed assembly or anti-vibration)

2. DEUTSCH connector

3. External antenna A60 (433) or A70 (870)

4. Removable internal EEPROM

5. TR800-CE MCX radio

6. External signaling LEDs

7. DEUTSCH connector pinout

8. Switches for the control of voltage options


Technical description


MP08V receiver installation

The below information describes hazards to be aware of during installation and steps to locate thereceiver.

Risk of shockCompletely shut down the machine when installing the receiver.Check the power supply and shut off the main switch to disconnect the interface cable between thereceiver and the machine's electrical box.

1. Find an easily accessible and clear location with a direct vision between the receiver's antenna andthe transmitter's working area.

2. Optional: If it is difficult to achieve direct vision between the receiver's antenna and the transmitter'sworking area, it is recommended to use an extended antenna in a clear location (only for models thatallow an antenna).

In areas of high vibration, the use of dampers is advised.

3. Proceed to connect the power supply. Use the connection block diagram provided with the system,where the correspondence between the transmitter maneuvers and the receiver's outputs aredetailed.

7IN2

8IN1

9MANUAL

10GND

11K3

12K1

6IN3

5IN4

4 3IN 0-10V

2K4

1K2IN 0-20mA

1PW

21SA4

31SA3

41SA2

51SA1

6GND

12STOP

11+12/24V

10 9 8 7

K1-4

1SA-4 1SA-3 1SA-2 1SA-1

A B

4. Check if the electrical installation and verify if there's an option to connect the neutral or the groundcable. In that case, don't forget to connect the ground cable.

The use of fireproof or flame retardant cables are recommended for the connection.


Installation


MP08 input and output configuration

This receiver has one analog input IN 0-10V (without isolation) or IN 0-20mA (without isolation). Theseinputs share the same hardware/pins and each one is selected by an internal jumper.

The two inputs cannot be live together at the same time.

The MP08 includes a 7.5A internal fuse.

MP08V digital outputs

The digital outputs k1-k8 have a common contact at pin A1 of the connector. Maximum 2A per output. Itis recommended to use K1 for by-pass valve.

DEUTSCH connector

K1

K2

K3

K4

K5

K6

K7

K8

Pin A1

Pin A12

Pin A2

Pin A11

Pin A3

Pin A10

Pin A4

Pin A9

Pin A5

Pin B2

external connection

Emergency Stop Output

MP08V analog outputs

This receiver allows to choose the control voltage to set up the output power, throughout the selectionof 1 switch.

Control voltage options: 0-5V, 0-10V, 0-Vcc

Analog 1 B7

Analog 2 B5

Analog 3 B8

Analog 4 B4

MP08V stop category 3 PLd

Stop function is performed with 2 relays in serie or in parallel.

B1 and B2 pines should not be connected directly to GND.


Installation


Serie

03.1.3- STOP Category 3 PLd (only in MP08V):

B

B

B

B

C M

NO

1-8

NO

A1

B 6 G ND

12

2

11

S T OP 1

S T OP 2

C M

B 10 V dc

C M

NO

1-8

NO

A1

B 6 G ND

1

S T OP 1

S T OP 2

C M

B 10

SERIE PARALELOExternal connection

STOP+IN

STOP+OUT

C M

NO

1-8

NO

A1

B 6

S T OP 1

S T OP 2

C M

B 10 V dc

C M

NO

1-8

NO

A1

B 6 G ND

S T OP 1

S T OP 2

B 10

alimentaciónsalidas digitales

B

B

B

B

12

2

11

1

STOP 1+OUT

STOP 2+IN

STOP 2+OUT

STOP 1+IN

conexión externa

03- RECEIVER INSTALLATION

B

B

B

B

C M

NO

1-8

NO

A1

B 6 G ND

12

2

11

S T OP 1

S T OP 2

C M

B 10 V dc

C M

NO

1-8

NO

A1

B 6 G ND

1

S T OP 1

S T OP 2

C M

B 10

SERIE PARALELOconexión externa

STO P+IN

STO P+OUT


C M

NO

1-8

NO

A1

B 6

S T OP 1

S T OP 2

C M

B 10 V dc

C M

NO

1-8

NO

A1

B 6 G ND

S T OP 1

S T OP 2

B 10

B

B

B

B

12

2

11

1

STOP 1+OUT

STOP 2+IN

STOP 2+OUT

STOP 1+IN

conexión externa

03.1.4- PINOUT

7IN2

8IN1

9MANUAL

10GND

11K3

12K1

6IN3

5IN4

4 3IN 0-10V

2K4

1K2IN 0-20mA

1PW

21SA4

31SA3

41SA2

51SA1

6GND

12STOP

11+12/24V

10 9 8 7

K1-4

1SA-4 1SA-3 1SA-2 1SA-1

A7IN2

A8IN1

A9K7

A10K5

A11K3

A12K1

A6In 0-10

A5K8

A4 A3 A2K4

A1K2

B1 B2 B3CANL

B4SA4

B5SA2

B6GND

B12 B11+12/24V

B10 B9 B8 B7CANH SA3 SA1K6 Power

K1-8

KSTOP2.1 KSTOP1.1

KSTOP2.2 KSTOP1.2

PINOUT MP08 A

PINOUT MP08 V

A B

A B

Diferencias entre MP08A y MP08V

Parallel

03.1.3- STOP Category 3 PLd (only in MP08V):

B

B

B

B

C M

NO

1-8

NO

A1

B 6 G ND

12

2

11

S T OP 1

S T OP 2

C M

B 10 V dc

C M

NO

1-8

NO

A1

B 6 G ND

1

S T OP 1

S T OP 2

C M

B 10

SERIE PARALELOExternal connection

STOP+IN

STOP+OUT

C M

NO

1-8

NO

A1

B 6

S T OP 1

S T OP 2

C M

B 10 V dc

C M

NO

1-8

NO

A1

B 6 G ND

S T OP 1

S T OP 2

B 10


B

B

B

B

12

2

11

1

STOP 1+OUT

STOP 2+IN

STOP 2+OUT

STOP 1+IN

conexión externa

03- RECEIVER INSTALLATION

B

B

B

B

C M

NO

1-8

NO

A1

B 6 G ND

12

2

11

S T OP 1

S T OP 2

C M

B 10 V dc

C M

NO

1-8

NO

A1

B 6 G ND

1

S T OP 1

S T OP 2

C M

B 10

SERIE PARALELOconexión externa

STO P+IN

STO P+OUT


C M

NO

1-8

NO

A1

B 6

S T OP 1

S T OP 2

C M

B 10 V dc

C M

NO

1-8

NO

A1

B 6 G ND

S T OP 1

S T OP 2

B 10

B

B

B

B

12

2

11

1

STOP 1+OUT

STOP 2+IN

STOP 2+OUT

STOP 1+IN

External connection

03.1.4- PINOUT

7IN2

8IN1

9MANUAL

10GND

11K3

12K1

6IN3

5IN4

4 3IN 0-10V

2K4

1K2IN 0-20mA

1PW

21SA4

31SA3

41SA2

51SA1

6GND

12STOP

11+12/24V

10 9 8 7

K1-4

1SA-4 1SA-3 1SA-2 1SA-1

A7IN2

A8IN1

A9K7

A10K5

A11K3

A12K1

A6In 0-10

A5K8

A4 A3 A2K4

A1K2

B1 B2 B3CANL

B4SA4

B5SA2

B6GND

B12 B11+12/24V

B10 B9 B8 B7CANH SA3 SA1K6 Power

K1-8

KSTOP2.1 KSTOP1.1

KSTOP2.2 KSTOP1.2

PINOUT MP08 A

PINOUT MP08 V

A B

A B



Installation


MP08V pinout

7 8 9 10 11 12

6 5 4 3 2 1

1 2 3 4 5 6

12 11 10 9 8 7


A B

Pin A Description Pin B Description

1 Power; K1-8 1 KSTOP2.1

2 K2 2 KSTOP1.1

3 K4 3 CANL

4 K6 4 SA4

5 K8 5 SA2

6 In 0-10 6 GND

7 IN2 7 SA1

8 IN1 8 SA3

9 K7 9 CANH

10 K5 10 +12/24V

11 K3 11 KSTOP1.2

12 K1 12 KSTOP2.2


Installation


Receiver troubleshooting

LED Characteristic Description Action

POWER Green; pulsing Receiver is starting up Wait until start-up process isfinished

HARDOK Green; continuous Receiver hardware OK Operate

Red; pulsing EEPROM error; data corruption; CAN bus error (if CANERRactivates)

Reprogram EEPROM

Red; other Electronic board hardware breakdown Replace device

SIGNAL LED off No radio signal detected -

LED on + transmitter switchedoff

Radio channel occupied Change transmitter's frequencychannel

LED on + DATA switched off Radio channel occupied by non Danfoss system Change transmitter's frequencychannel

DATA LED off + SINGAL LED on Radio error Replace radio

Green; pulse Receiving good frames OK

ID LED off + DATA LED on No valid ID; Danfoss system nearby If channel not occupied, checkchosen ID in the transmitter orreset the receiver

LED on + SIGNAL LED on +DATA LED on

Valid frames received from the transmitter; correct link OK

RELAY Green STOP relay activated -

ORDER Green - -


Troubleshooting


Danfoss Power Solutions is a global manufacturer and supplier of high-quality hydraulic andelectric components. We specialize in providing state-of-the-art technology and solutionsthat excel in the harsh operating conditions of the mobile off-highway market as well as themarine sector. Building on our extensive applications expertise, we work closely with you toensure exceptional performance for a broad range of applications. We help you and othercustomers around the world speed up system development, reduce costs and bring vehiclesand vessels to market faster.

Danfoss Power Solutions – your strongest partner in mobile hydraulics and mobileelectrification.

Go to www.danfoss.com for further product information.

We offer you expert worldwide support for ensuring the best possible solutions foroutstanding performance. And with an extensive network of Global Service Partners, we alsoprovide you with comprehensive global service for all of our components.

Local address:

Danfoss Power Solutions GmbH & Co. OHGKrokamp 35D-24539 Neumünster, GermanyPhone: +49 4321 871 0

Danfoss Power Solutions ApSNordborgvej 81DK-6430 Nordborg, DenmarkPhone: +45 7488 2222

Danfoss Power Solutions (US) Company2800 East 13th StreetAmes, IA 50010, USAPhone: +1 515 239 6000

Danfoss Power Solutions Trading(Shanghai) Co., Ltd.Building #22, No. 1000 Jin Hai RdJin Qiao, Pudong New DistrictShanghai, China 201206Phone: +86 21 2080 6201

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to productsalready on order provided that such alterations can be made without subsequent changes being necessary in specifications already agreed.All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.

© Danfoss | August 2020 BC292480424603en-000102

Products we offer:

• DCV directional controlvalves

• Electric converters

• Electric machines

• Electric motors

• Gear motors

• Gear pumps

• Hydrostatic motors

• Hydrostatic pumps

• Orbital motors

• PLUS+1® controllers

• PLUS+1® displays

• PLUS+1® joysticks andpedals

• PLUS+1® operatorinterfaces

• PLUS+1® sensors

• PLUS+1® software

• PLUS+1® software services,support and training

• Position controls andsensors

• PVG proportional valves

• Steering components andsystems

• Telematics

Hydro-Gearwww.hydro-gear.com

Daikin-Sauer-Danfosswww.daikin-sauer-danfoss.com

Documents

MP08V Receiver User Manual - DanfossSERIE PARALELO conexión externa STOP +IN STOP +OUT alimentación salidas digitales CM NO 1-8 NO A1 B6 STOP1 STOP2 CM B10 Vdc GND B B B B 12 2 11