MOVE IT. LOAD IT. SPREAD IT .

PU

LL S

PREA

DER

S A

ND

MO

UN

TED

TEN

DER

S

PULL SPREADERS AND MOUNTED TENDERSS-150•S-500•S-600•S-800 | TENDERS 1600•16•24

For almost 50 years, Willmar® has set the benchmark for dry fertilizer spreaders and tenders. With recommended maintenance

and care from an authorized Willmar dealer, these ruggedly built spreaders and tenders will provide years of reliable service.

From the sales process to full-service product support, your Willmar dealer is committed to delivering an ownership experience that

matches the professional-level performance of your new equipment. Best-in-class performance and best-in-class support . . . it’s

what you expect from Willmar products and the knowledgeable, industry-savvy people who stand behind them.

.

BIG PERFORMANCE. BIGGER SUPPORT.

The corrosive effect of fertilizers can be substantial and very costly. Every Willmar pull-type spreader features corrosion-

resistant phenolic flooring to facilitate material flow without buildup from under the conveyor chain. Both the conveyor and

ground-drive chains are made with stainless steel, frames are structural channel steel with reinforcements, and the hopper and

skid are constructed of 12-gauge stainless steel. A chemical-resistant, epoxy based, rust-inhibiting primer and super tough,

acrylic, urethane finish combine to protect and extend the life of the spreader.

Although Willmar spreaders can’t control the volatility of fertilizer prices, they can help improve your margins by delivering

fertilizer more accurately and efficiently. They’ve long been acknowledged for their durability, ease of operation and agility —

just some of the reasons Willmar is the spreader of choice for many in the industry.

LINED AND SEALED TO DELIVER.

NIMBLE AND QUICK.S-150

SMALL AND PRECISE. The S-150 has a heaped

capacity of 53.6 cubic feet (1.51 m3). It features dual

spinners that deliver material in a 100% overlap pyramid

type pattern that reduces spread pattern variations due to

wind and rough terrain.

ORCHARD FRIENDLY. With the addition

of the optional orchard deflector, total

spread is 15 to 25 feet (4.5–7.6 m), and is

designed to place the bulk of the material at

the center of orchard rows.

With up to twelve wheel track options, the mid-size, 5-ton (4536 kg) S-500 is versatile enough to adapt to nearly any situation. You can add to the

versatility of the S-500 by choosing from one of two different PTO drives or by adding an optional 8-hp (5.9 kW) engine for driving the spinner

system.

SMOOTH OPERATION. A multi-leaf, spring suspension system

positioned on both sides of each axle to reduces bounce and

improves stability. Optional 2- or 4-wheel, hydraulic surge brakes

provide additional braking capability during transport for added

safety.

CONSTANT, EVEN FLOW. Control application rates from 524 to

1,045 pounds (238–475 kg) of material per acre with the two-speed

conveyor. Simply move the hand lever to align with the

corresponding gate opening number to meter material flow. The

stainless steel gate moves freely without binding or freezing up. A

front- to rear-adjustable baffle plate allows you to determine flow to

accommodate variations in material density, weight and size.

CUSTOMIZABLE. The S-500 is available in single- or dual-

spinner configurations. Choose from the single-spinner configuration

delivers a 65-foot (19.8 m) total spread pattern, dual 40-foot (12.2 m)

spinners with an 80-foot (24.4 m) total spread or dual 50-foot (15.2

m) spinners with a 100-foot (30.5 m) total spread. The dual spinner

options create a pyramid-style spread pattern that provides 100%

overlap.

ADDED SAFETY. Lighting and reflective devices that meet ASAE

S279 lighting and marking requirements for on-road travel are

standard on the S-500.

THE CREAM OF ANY CROP.

- 62 inches (157 cm) with no brakes, or two- or four-wheel brakes- 64 inches (163 cm) with no brakes - 66 inches (168 cm) with no brakes- 68 inches (173 cm) with no brakes - 70 inches (178 cm) with no brakes - 72 inches (183 cm) with no brakes

NARROW: STANDARD:

- 77 inches (196 cm) with no brakes, or two- or four-wheel brakes- 88 inches (224 cm) with no brakes

S-500

TRACK OPTIONS.

NO JOB IS TOO BIG.Durable, productive, accurate and dependable — the S-600 and S-800 are all that and more. These spreaders have the capacity you need

for big jobs, and allow you to spend more time in the field and less time loading.

CONVEY IT BETTER. A mechanically simple chain and gear

conveyor system is directly driven by the spreader’s ground speed

through chains and pulleys. A slip clutch prevents damage to the

components if the conveyor belt unintentionally stops and conveyor

shields guide the slackened chain over the cross members to

prevent metal-to-metal contact. The two-speed conveyor allows you

to control application rates in low or high ranges, from 311 to 1,033

pounds (141–469 kg) of material per acre.

DRIVEN FOR SUCCESS. The S-600 and S-800 spreaders

come standard with a 540 PTO. For even more versatility, a dual

drive 540/1000 PTO is available as an option. Both can be

configured with either a single- or dual-spinner and produce the

same spread patterns as our other equipment for precision

application.

THE PERFECT SETUP. Setup is quick and easy. Hitch the

spreader up to your tractor, connect the PTO and set the gate

height. The S-600 hopper boasts an incredible 192 cubic feet (5.46

m3) struck capacity; 210 cubic feet (5.95 m3) heaped. Its big

brother, the S-800, holds 244 cubic feet (6.90 m3) struck and 264

cubic feet (7.47 m3) heaped.

SEE AND BE SEEN. For added safety, these larger units are

equipped with lighting and reflective devices that meet the ASAE

S279 lighting and marking requirements for agricultural machinery

operating on the road. For added convenience, a window at the

front of the S-800 spreader gives you a clear visual on the

remaining product.

S-600 AND S-800

S-600 ONLY62 inches (157 cm) with two- or four-wheel brakes

For the S-600, 75 inches (191 cm) or 88 inches (232 cm) with two- or four-wheel brakesFor the S-800, 75 inches (191 cm) or 88 inches (232 cm) with four-wheel brakes

NARROW: STANDARD:TRACK OPTIONS.

If you’ve got a lot of material to move, using the right tender can make all the difference for your bottom line. Willmar’s 16- (14,545 kg) and 24-ton

(21,818 kg) side-shooting tenders can be either truck or trailer mounted* and can move up to two tons of material a minute. Contributing to that

efficiency are four- or six-compartment hoppers that can carry a variety of materials; steep, 40-degree, sloped sides for quick material dispensing;

large-diameter, 10-inch (25.4 cm) augers and big hydraulic capacity.

LOADS OF CAPACITY. The 16-ton (14,545 kg) version holds an

incredible 516 cubic feet (14.6 m3) struck and 570 cubic feet (16.1

m3) heaped while the 24-ton (21,818 kg) weighs in with a struck

capacity of 774 cubic feet (21.9 m3) and 885 cubic feet (24.2 m3)

heaped. Two stainless steel, gate control handles facilitate easy

individual hopper unloading, and a wide-mouthed bottom dump gate

accommodates pit unloading.

LOADS OF FEATURES. Located on the front left catwalk, there

are separate controls for on/off horizontal and side discharge, fold/

unfold and raise/lower auger control. The one-piece, adjustable,

swing- away auger engages with a spring-loaded back to eliminate

spillage. The hydraulic drive with PTO-powered pump has a large 25-

gallon (94.6 L) hydraulic oil reservoir so you’ll always have power

when you need it.

*46,000-pound (20,909 kg) gross volume weight (GVW) truck or trailerrequirement, depending on model.

HIGH CAPACITY, EFFICIENT LOADINGSIDE-SHOOTER 16/24 TENDERS

SERIOUS MATERIAL HANDLING.Willmar’s truck-mounted* rear discharge tenders are ideal for commercial fertilizer dealers, custom applicators and large farming operations.

With two large-capacity hoppers that feed into one auger, these tenders can carry nearly any single, dry-material product and load any

applicator or planter at up to two tons per minute.

A STEP ABOVE. Rear-mounted ladders provide accessibility to

the hoppers to improve the sightline of the fill and flow status.

Cleanout is quick and thorough with 30º (1600 model) fast-flow,

stainless steel sides.

THE BEST POUND-FOR-POUND. Discharge rates range from

2,400 (5,280 kg) pounds of urea per minute to 4,000 pounds (8,800

kg) of potash per minute. The standard auger is 10 inches (25.4

cm) in diameter by 19 feet long (5.8 m) with a discharge height to

108.25 inches (275 cm). A 21-foot-long (6.4 m) auger with 117-inch

(297.2 cm) discharge height is also available.

LOADED WITH FEATURES. Auger on/off controls and raise/

lower controls are located on the left rear corner of the tender. The

self-contained hydraulic system is PTO-driven and has a 10-gallon

(37.85 L) reservoir.

*32,000- (14,515 kg) or 40,000-pound (18,144 kg) gross volume weight(GVW) truck requirement.

REAR DISCHARGE TENDERS

STANDARD EQUIPMENT: S-150, S-500, S-500 NT, S-600, S-600 NT, S-800 PULL-TYPE SPREADERS

SPECIFICATIONS: 1600 TENDERSSPECIFICATIONS: 16- AND 24-TON SIDE SHOOTER TENDERS

AGCO PARTSAGCO Parts supports dealers with world-class service, providing tools like agcopartsbook.com to put parts information at your fingertips 24/7.

AGCO, Your Agriculture Company, is a premier manufacturer of agricultural equipment, providing high-tech solutions for professional farmers feeding the world. The company is dedicated to delivering superior customer service, innovation and quality. AGCO products are distributed in more than 140 countries worldwide.

AGCO FINANCEAt AGCO Finance, we understand that financing is as much a part of your purchase decision as the features and benefits of the product. So we’re committed to providing the best means of acquiring the equipment you need, while allowing you to preserve other credit lines of operating capital.

Find a dealer at applylikeapro.com

©2016 AGCO Corporation. AGCO® and Willmar® are registered trademarks of AGCO Corporation. AGCO Advanced Technology Solutions is a worldwide brand of AGCO Corporation. AGCO Corporation has a corporate policy of continuous improvement and development; therefore, specifications are subject to change without any advance notice. AGCO Corporation is not responsible for differences between the specifications or illustrations contained in this publication and the actual equipment. Equipment produced by other manufacturers is shown in photographs in this brochure for the purpose of illustration only and is not intended as an endorsement of that particular equipment or its suitability. All rights reserved.

WL15B001IS

AGCO ANSWERS At AGCO, customer care isn’t just a department. It’s a commitment. Contact us with your questions, we’ll do our best to answer them promptly or put you in touch with someone who can. Call 877-525-4384 or email agcoanswers@agcocorp.com