Mounting Frame Pearl...Kit, wall over each of the pin bolts. 7 Installing the Mounting Frame in the Wall Cavity Note that three installation methods are available. 8 Position the frame

Mounting Frame Pearl Tel. +47 70 03 91 00www.jetsgroup.com

Product No. MF690MS 2018-06-05 05:59

1

A solution for mounting selected toilets in Jets™ product range. Designed to add structural strength for wall mounted products.

WarrantyAll products of the company are sold and all services of the company are offered subject to Jets Vacuum AS General Sales Conditions detailing warranty and terms and conditions of sale, copies of which will be furnished upon request. The information provided herein is for guidance only; it does not constitute a guarantee of the performance or specification of any individual product or component.

Technical Data

.................................................................................................... .........................................................................................................................................Generic Material Steel

.................................................................................................... .........................................................................................................................................Coating Galvanized

.................................................................................................... .........................................................................................................................................Net Weight N/A

Patents and TrademarksJets™, Vacuumarator™, Helivac™, VC™, VOD™, CVS™ and Softsound™ are trademarks and/or registered trademarks of Jets. © Copyright 2011, Jets AS.

DisclaimerProduct color reproduction is as near to actual color as product methods allow. All rights reserved. Jets Vacuum AS has a policy of continuous improvement on its products and reserves the right to change materials and specifications without notice. Information herein is current at the time of printing and is subject to change without notice. No part of this document may be reproduced in any form by any means without prior written approval of Jets Vacuum AS.

ComponentsConstruction Characteristics

1 Mounting Frame Pearl.................................................................................................... .........................................................................................................................................069000120*

2 Fastening Kit, wall.................................................................................................... .........................................................................................................................................069606411*

* Component/s avaliable as replacement parts.

AccessoriesConstruction Characteristics

Fastening Kit, wall - Land.................................................................................................... .........................................................................................................................................069606409Pipe Fixture, Pearl.................................................................................................... .........................................................................................................................................034608310


Product No. MF690MS 2018-06-05 05:59

2

Important Health and Safety InformationInstallation, operation and maintenance must be carried out in strict accordance with this guide and with all applicable regulations. For your own protection and the protection of others, it is necessary to familiarize yourself with, and always follow, the contained safety and environmental precautions for our products.

This manual is an integral part of the product/delivery. Always keep it in a safe place for future reference. It is entirely the owner’s responsibility to ensure that all safety and environmental measures, in accordance with local, state and federal laws are followed. Jets Vacuum AS assumes no responsibility for equipment damage, personal injury or death and/or delays that result from a lack of respect for the instructions for installation and/or use as stated in this documentation. Disregarding these instructions may invalidate all warranties.

Safety information references are in accordance with Jets Vacuum AS documentation system. If you do not understand the warnings, stop work immediately and contact Jets Vacuum AS (citing the safety reference number) for further clarification.

For further information about the included warnings or any other safety concerns please contact Jets Vacuum AS.

Safety Warning SymbolsSymbol denotes required personal protective equipment is required. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result

in minor or moderate injury or equipment damage.

Important Health and Safety Warnings

1.4 CautionSafety equipment (PPE) necessary for the prevention of accidents at the installation and operating site must be provided in accordance with local regulations.

1.5 Personal Protective Equipment - GogglesWear safety glasses with side shields at all times when working with equipment.

1.6 WarningKeep work area clean, uncluttered and ensure adequate lighting.

1.7 WarningKeep other persons at a safe distance from work area.

Delivery, Receipt of Goods and TransportationGoods to be protected against shock, dust, humidity and frost. Suitable adequately dimensioned transporting equipment is to be used. Note that the equipment may contain components that are easily damaged as a result of inappropriate handling. Jets Vacuum AS is not responsible for or liable for delivery delays resulting from occurrences outside of Jets Vacuum AS' immediate control. On receipt of goods, check for visual damage. Any damage detected after dispatch should be reported immediately to Jets Vacuum AS. Damages and/or discrepancies must be reported in writing no later than eight (8) days after receipt of goods. Commissioning must be postponed until the equipment has been inspected. Do not dispose of damaged items. Your direct supplier will advise you of the procedure to follow.

StorageUnless otherwise specified, goods are to be stored in a dry environment between -30°C and +40°C prior to installation. The storage location must be dust free, low humidity (≤95%) and be free from moisture. Keep clear of foreign objects.

Installation to End UseSite to be a dry environment between +0°C and +45°C. Use in environments below 0°C requires use of antifreeze in liquids. The site location is to be low vibration Vrms ˂0.2 mm/s) with vibration resistance to acceleration up to 0.7g. The site is to be dust free and protected from grinding and welding. During installation, the site is to be protected from water, frost, moisture and humidity. Goods are to be stored as per the instructions fordelivery, storage and transport. A visual inspection is to be carried out on receipt of goods as well as at the time of installation to ensure that storage and transport conditions after receipt have not compromised the quality of the product/s.


Product No. MF690MS 2018-06-05 05:59

3

Installation

1

Mounting Frame PreparationThe Mounting Frame Pearl is supplied with all required components for a standard installation.

(A) Mounting Frame Pearl(B) Fastening Kit, wall

2

When planning the installation ensure that the maximum distance between the top of the structure of the frame and the stud above is 50mm. Do not extend the sliding arm beyond 50mm as this will compromise the strength of the Mounting Frame Pearl. This applies to all installations in which the sliding arms are in use.

3

Insert the six (6) pin bolts ② included in the delivery (Fastening Kit, wall) in the holes as indicated.

4

When screwing in the pin bolts, note that the hexagon screw end (E) of the pin bolt is to face outwards (i.e. towards the toilet) so that it is accessible from the front of the installation.

5

Pin bolts are to be screwed into the frame to the depth required based on the wall thickness. Note that once mounted in the wall, the bolts should protrude from the surface of the wall.

6

Slide one of the six (6) protection tubes included in the Fastening Kit, wall over each of the pin bolts.

7

Installing the Mounting Frame in the Wall CavityNote that three installation methods are available.

8

Position the frame in the wall cavity. Note that the frame must be affixed to adequately dimensioned weight bearing studs for fixing, above, behind or to the sides of the frame. Installation Method 1: Mounted in front of the stud with a stud behind the top of the frame.

Installation Method 2: Mounted in between studs with a stud above the top of the frame.

Installation Method 3: Mounted in between studs with no stud above the top of the frame (attached to side studs). This method requires screws which are not included in the standard delivery. Contact Jets™ or your distributor for a suitable mounting kit.

9

Installation Method 1: Mounted in front of Stud(A) Upper Rear Bracket Bolts (B) Bracket Bolts on Frame Base Plate

10

Using the adjustment bolts on the side of the frame (A), adjust the height of the frame to suit your requirements

Adjust the position of the frame using a water level. Ensure that the frame is level.


Product No. MF690MS 2018-06-05 05:59

4

11

It is recommended that the frame be positioned with a mounting height from the floor of 350mm (B) . This will result in a final toilet seat height of approx. 430mm.

12

Position the frame in front of the stud. The sliding bracket can be adjusted to suit both varying height between the stud and the top of the frame and also depth from the frame to the stud.

13

Adjust the base plates to the required height. Secure the two lower bolts (left and right) on the frame base plates to the lower stud/surface (A).

14

Turn the sliding bracket to be horizontal and adjust the sliding bracket (A) to the stud. Using a water level, check that the frame is level (horizontally and vertically). Secure the two upper rear bracket bolts (left and right) to the stud (B).

15

If the sliding bracket is longer than required, cut (A) the sliding bracket such that it will fit within the wall cavity depth.

16

Position the Mounting Frame Pearl in the wall cavity with the pin bolts protruding through the pre-prepared holes (as per the drill pattern). Note that the pin bolts may need to be re-adjusted to ensure sufficient bolt protrudes through the wall (20mm).

17

Installation Method 2: Mounted between Stud and Floor(A) Upper Rear Bracket Bolts (B) Bracket Bolts on Frame Base Plate

18

Using the adjustment bolts on the side of the frame (A), adjust the height of the frame to suit your requirements

Adjust the position of the frame using a water level. Ensure that the frame is level.

19


20

Secure the two lower bolts (left and right) on the frame base plates to the lower stud/surface (B).

21

Turn the sliding bracket to be vertical and adjust the sliding bracket (C) to the stud. Using a water level, check that the frame is level (horizontally and vertically). Secure the two upper rear bracket bolts (left and right) to the stud (A).

22

Position the Mounting Frame Pearl in the wall cavity with the pin bolts protruding through the pre-prepared holes (as per the drill pattern). Note that the pin bolts may need to be re-adjusted to ensure sufficient bolt protrudes through the wall (20mm).


Product No. MF690MS 2018-06-05 05:59

5

23

Installation Method 3: Mounted to Side StudsTo mount the frame with no overhead stud, it is necessary to remove indicated components from the assembly.

● Unscrew and remove the sliding brackets and upper rear bracket bolts.

● Unscrew and remove the lower adjustable base plates and bolts.

24


25

Secure the frame to the side studs using a minimum of four (4) and up to six (6) screws (A).

Note: Screws are not included in the delivery.

A suitable kit for this purpose is available in Jets™ product range.

26

The installation of the Mounting Frame Pearl is complete. Refer to the following steps to prepare the wall surface.

27

Placement and Wall Cutout Procedures

The following procedures require cutout of the wall panel on which the toilet is to be mounted.

28

Drill PatternA drill pattern is supplied to aid in drill hole and cutout placement. Standard toilet height is indicated in the installation instructions on the drill pattern. For public toilet, handicapped toilet or other toilet height installations, the pattern should be adjusted in height accordingly.

29

Drill Pattern Markers:

(A) Ø10mm holes required for the Wall Fixture for seat and the Mounting Frame Pearl.(B) Level Mark (for standard installation, affix the drill pattern to the wall per instructions on the drill pattern).(C) Main Cutout (mark the cutout per the pattern on the wall surface. Do not cut outside of the line).The instructions provided in the description (and on the drill pattern) will result in a final toilet seat height of approx. 430mm.

30

Measure the bolt heights for the cutout using the mounting frame installed in the wall cavity as a guide.

31

Affix the drill pattern to the wall pattern, taking into consideration the location of supporting studs required for mounting the frame. Using the horizontal mark on the cutout as a guide, ensure that the cutout is level. This is best achieved with a water level or a laser level.

32

Drill holes for the support pin bolts as indicated on the drill pattern (A).


Product No. MF690MS 2018-06-05 05:59

6

33

Saw out and remove the main cutout. The cutout is completed and ready for installation on the Mounting Frame Pearl.

34

Lift the wall panel and position it on the wall with the bolts from the mounting frame protruding through the bolt holes in the cutout.

Documents

Mounting Frame Pearl...Kit, wall over each of the pin bolts. 7 Installing the Mounting Frame in the Wall Cavity Note that three installation methods are available. 8 Position the frame