motion-control NC61 chap08 English 2010.book Seite 1 ... · PDF fileSiemens NC 61 · 2010 8/2 Introduction 8/4 1PH8 motors With solid shaft/hollow shaft ... Rated torque Mrated Selection

Siemens NC 61 · 2010

8/2 Introduction

8/4 1PH8 motorsWith solid shaft/hollow shaftForced ventilation/Water cooling

8/18 1PH7 motorsWith solid shaftForced ventilation

8/34 1PH4 motorsWith solid shaftWater cooling

8/38 1PH2 built-in motorsFor direct driveWater cooling

8/42 Liquid coolingCooling principleCooling unit manufacturers

8/43 GearboxesTwo-speed gearboxesfor 1PH7/1PH4 motors

8/45 Selection guidesType of construction/mounting positionDegree of protection

8/46 Dimensional drawings8/46 1PH8 motors8/64 1PH7 motors8/72 1PH4 motors8/74 1PH7 motors with gearbox8/75 1PH4 motors with gearbox8/76 1PH2 motors

Part 11 CAD CREATORDimension drawing and2D/3D CAD generatorwww.siemens.com/cadcreator

Asynchronous motors

motion-control_NC61_chap08_English_2010.book Seite 1 Mittwoch, 13. Januar 2010 12:58 12

© Siemens AG 2010

Asynchronous motorsIntroduction

Type overview and rated data

8/2 Siemens NC 61 · 2010

8■ Application

The areas of application for the 1PH asynchronous motors are extremely varied.

In machine tools, they are usually used as main spindle motors.

In production machines, such as printing, packaging and re-forming machines, they are used as high-output asynchronous servo motors.

The motors are referred to generally in this documentation as asynchronous motors, due to their principle of operation.

1) Fan IP55, optional: IP66.2) SH 180 and higher: IP55.3) Fan IP54.4) IP55 at shaft exit.5) As specified by spindle manufacturer.

Motor type Designation Degree ofprotection

Cooling method

1PH8 Asynchronous motorThree-phase squirrel-cage motorwithout casingMain spindle motorSolid shaft/hollow shaft

IP551)

IP55/IP652)

Forced ventilation

Water cooling

1PH7 Asynchronous motorThree-phase squirrel-cage motorwithout casingMain spindle motorSolid shaft

IP553) Forced ventilation

1PH4 Asynchronous motorThree-phase squirrel-cage motorMain spindle motorSolid shaft

IP654) Water cooling

1PH2 Asynchronous built-in motorThree-phase squirrel-cage motorIndividual componentsMain spindle motor for direct drives

IP005) Water cooling


© Siemens AG 2010

Asynchronous motorsIntroduction

Type overview and rated data

8/3Siemens NC 61 · 2010

8■ Application (continued)

Core types can be supplied for certain motor types. These core types can be express delivered as replacement motors in the event of plant outages and offer the advantage of a quicker spare parts supply. For this reason, core types should be used for configuration wherever possible.

The selection and ordering data for the SINAMICS S120 Motor Modules are based on the booksize format by way of example. Blocksize and chassis formats are also possible. The SIZER configuration tool is available for detailed configuration.

Shaft height Rated power Prated for S1 duty kW (HP)

Rated torque Mrated

Selection and ordering data

0.1 1 10 100 1000 Page

SH 80/SH 100/SH 132

SH 80/SH 100/SH 132/SH 180/SH 225/SH 280

10 ... 162 Nm(7.38 ... 119 lbf-ft)14 ... 2602 Nm(10.3 ... 1919 lbf-ft)

8/6 ... 8/9

8/10 ... 8/13

SH 100/SH 132/SH 160/SH 180/SH 225

23.6 ... 1080 Nm(17.4 ... 797 lbf-ft)

8/20 ... 8/33

SH 100/SH 132/SH 160 48 ... 331 Nm(35.4 ... 244 lbf-ft)

8/36 ... 8/37

Outer diametermm (in)205/250 (8.07/9.84)

48 ... 146 Nm(35.4 ... 108 lbf-ft)

8/40 ... 8/41

2.8 (3.75) 29 (38.9)

3.5 (4.69) 227 (304)

3.7 (4.96) 205 (275)

7.5 (10.1) 52 (69.7)

7.5 (10.1) 23.6 (31.6)


© Siemens AG 2010

Asynchronous motorsMain spindle motors for SINAMICS S120

1PH8 motors

8/4 Siemens NC 61 · 2010

8

■ Overview

The 1PH8 motors are compact asynchronous motors with a squirrel-cage rotor and degree of protection IP55/IP65. They extend and replace the current power spectrum of our proven 1PH/1PM series. The 1PH8 motors are available in two different cooling types:• Forced ventilation• Water cooling

These motors have been designed specifically for use in con-junction with the SINAMICS S120 drive system. Depending on the control requirements, appropriate encoder systems are available for the motors for sensing the motor speed and indirect position.

As a standard, the encoder system for machine tools is C axis capable, an additional encoder for C axis mode is not necessary.

■ Benefits7 Broad power spectrum7 The right design for any application

• Forced ventilation or water cooling • Solid shaft or hollow shaft • Diverse bearing concepts • Different encoder types for closed-loop speed control and

high-precision positioning mode7 Excellent performance features

• Maximum speeds of up to 20000 rpm• Excellent rotational accuracy of up to 10 µm • Excellent vibration magnitudes• High dynamic performance (short ramp-up times)

7 Low noise emission7 Simple, flexible connection system7 Commissioning with electronic rating plate and

DRIVE-CLiQ interface

Water cooling is advantageous:7 Wherever extreme ambient conditions, such as high tempera-

tures, dust, dirt, or a corrosive atmosphere, do not permit air cooling

7 In processes in which the environment must not be heated

■ Application• Compact machine tools• Complex machining centers and turning machines• Fully encapsulated milling machines • High-load milling spindles• Counterspindles or driven tools for turning machines• Directly driven tools with internal cooling• Special machines

■ Characteristic curves

Typical speed/power graph for 1PH8 asynchronous motors1)

The graph shows the typical relationship between motor speed and drive power for 1PH8 motors for S1 duty (continuous duty) in accordance with IEC 60034-1.

Data for S2 short-time duty and S6 continuous duty can be found in the 1PH8 Motors Configuration Manual.

1) For further configuration information, see the 1PH8 Motors Configuration Manual.

Motor power

Voltage limit

Speed

Constant power range (field weakening operation)

nrated n2 nmax1

Pmax

PratedS1

nmax2 nmax3

n0

0

P

G_N

C01

_EN

_004

05


© Siemens AG 2010


1PH8 motors

8/5Siemens NC 61 · 2010

8

■ Technical specifications

S/R = signals/revolution

1) DE is the drive end with shaft. NDE is the non-drive end. 2) SINAMICS S120 booksize format: 4 kHz/chassis format: 2 kHz.3) Shaft extension run-out, concentricity of centering ring and shaft, and perpendicularity of flange to shaft.

Product name 1PH8 motor

Cooling Forced ventilation Water cooling

• Cooling water pressure at inlet, max. – 6 bar

Cooling water volume

Connecting thread at NDE1)

- 1PH808 – 6 l/min (1.59 US gallons/min.) G 1/8"






Ambient temperature, admissible -15 ... +40 °C (5 ... 104 °F)

Coolant inlet temperature – < 30 °C (86 °F)

Temperature monitoring KTY 84 temperature sensor in the stator winding

• 1PH818/1PH822/1PH828 – Additional KTY 84 as spare

Insulation of the stator winding in accordance with EN 60034-1 (IEC 60034-1)

For an ambient temperature of up to 40 °C (104 °F)

• 1PH808/1PH810/1PH813 Temperature class 155 (F)

• 1PH818/1PH822/1PH828 Temperature class 180 (H)

Motor fan ratings –

• 1PH808 230 V ± 10 %, 50 Hz265 V ± 10 %, 60 Hz

–

• 1PH810/1PH813 400 V 3 AC ± 10 %, 50 Hz480 V 3 AC ± 10 %, 60 Hz

–

Encoder system, built-in Without DRIVE-CLiQ interface or with DRIVE-CLiQ interface

Sound pressure level LpA (1 m) in accordance with EN ISO 1680Tolerance + 3 dB

Rated pulse frequency 4 kHz Rated pulse frequency 4 kHz/2 kHz2)

• 1PH808/1PH810 70 dB 68 dB

• 1PH813 72 dB 68 dB

• 1PH818/1PH822 – 70 dB

• 1PH828 – 72 dB

Connection

• 1PH808/1PH810/1PH813 Power connector or terminal box

• 1PH818/1PH822/1PH828 – Terminal box

• Fan- 1PH808 Power connector –- 1PH810/1PH813 Power connector or terminal box –

• Encoder system Connector for signals (without mating connector) or DRIVE-CLiQ

Vibration magnitude In accordance with Siemens/EN 60034-14 (IEC 60034-14)

Shaft and flange accuracy in accordance with DIN 42955 (IEC 60072-1)3)

Tolerance R

Degree of protection in accordance with EN 60034-5 (IEC 60034-5)

• 1PH808/1PH810/1PH813 IP55 IP65

• 1PH818/1PH822/1PH828 – IP55

• Fan IP55, optional: IP66 –

Rating plate 1 unit attached to motor 1 unit supplied loose in terminal box

Paint finish Anthracite RAL 7016

Approvals, according to cURus


© Siemens AG 2010

Asynchronous motorsMain spindle motors for SINAMICS S1201PH8 motors, standard type SH 80 to SH 132 – Forced ventilation

8/6 Siemens NC 61 · 2010

8

■ Selection and ordering data

The values in the selection and ordering data are applicable when using an Active Line Module with 400 V 3 AC line connection. When using a Smart Line Module, proceed according to 1PH8 Motors Configuration Manual.

Rated speed

Continuous speed, max.1) Rated power for S1 duty

Rated torque Static torque

1PH8 asynchronous motor Standard type

nrated nmax12) nmax2

3) nmax34) n2

5) Prated Mrated M0

rpm rpm rpm rpm rpm kW (HP) Nm (lbf-ft) Nm (lbf-ft) Order No.

Shaft height SH 80 – Forced ventilation – Line voltage 400 V 3 AC, operation on Active Line Module

1500200030004500

10000100001000010000

12000150001500015000

–170002000020000

6200113501730020000

2.8 (3.75)3.7 (4.96)4.1 (5.50)4.8 (6.44)

18 (13.3)18 (13.3)13 (9.59)10 (7.38)

21 (15.5)21 (15.5)21 (15.5)19 (14.0)

1PH8083-17F 77-77711PH8083-17G77-77711PH8083-17M77-77711PH8083-17N77-7771

1500200030004500

10000100001000010000

14000150001500015000

–180002000020000

6750104502000020000

3.7 (4.96)4.9 (6.57)4.8 (6.44)5.8 (7.78)

24 (17.7)23 (17.0)15 (11.1)12 (8.85)

27 (19.9)27 (19.9)27 (19.9)25 (18.4)

1PH8087-17F 77-77711PH8087-17G77-77711PH8087-17M77-77711PH8087-17N77-7771


1500 9000 12000 – 8350 3.7 (4.96) 24 (17.7) 29 (21.4) 1PH8101-17F 77-7771

1000150020003000

9000900090009000

12000120001200012000

–––18000

380052007200

17100

3.7 (4.96)5.5 (7.38)7 (9.39)8.4 (11.3)

35 (25.8)35 (25.8)33 (24.3)27 (19.9)

38 (28.0)38 (28.0)38 (28.0)38 (28.0)

1PH8103-17D77-77711PH8103-17F 77-77711PH8103-17G77-77711PH8103-17M77-7771

1500 9000 12000 – 6700 7 (9.39) 45 (33.2) 52 (38.4) 1PH8105-17F 77-7771

1000150020003000

9000900090009000

12000120001200012000

–––18000

545062507500

18000

6.3 (8.45)9 (12.1)

10.5 (14.1)12 (16.1)

60 (44.3)57 (42.0)50 (36.9)38 (28.0)

63 (46.5)63 (46.5)63 (46.5)59 (43.5)

1PH8107-17D77-77711PH8107-17F 77-77711PH8107-17G77-77711PH8107-17M77-7771


1500 8000 10000 11000 6050 11 (14.8) 70 (51.6) 96 (70.8) 1PH8131-17F77-7771

100015002000

800080008000

100001000010000

–1300015000

460069006500

12 (16.1)15 (20.1)20 (26.8)

115 (84.8)96 (70.8)96 (70.8)

128 (94.4)126 (92.9)126 (92.9)

1PH8133-17D77-77711PH8133-17F77-77711PH8133-17G77-7771

1500 8000 10000 14000 7500 18.5 (24.8) 118 (87.0) 157 (116) 1PH8135-17F77-7771

100015002000

800080008000

100001000010000

120001500015000

540070005500

17 (22.8)22 (29.5)28 (37.5)

162 (119)140 (103)134 (98.8)

183 (135)172 (127)176 (130)

1PH8137-17D77-77711PH8137-17F77-77711PH8137-17G77-7771

For versions, see Order number supplement and options.


© Siemens AG 2010


1PH8 motors, standard typeSH 80 to SH 132 – Forced ventilation

8/7Siemens NC 61 · 2010

8

1) Observe maximum speed of encoders.2) Bearing version for standard. 3) Bearing version for performance. 4) Bearing version for high performance. 5) Maximum permissible thermal speed at constant power or speed which is at the voltage limit when P = Prated.6) Additional weight for version with hollow shaft: 2.5 kg (5.51 lb).

Motor type(repeated)

Efficiency Moment of inertia

Weight, approx.6)

Rated current for S1 duty

Static current

SINAMICS S120 Motor Module

Rated output current for S1 duty

Booksize formatFor additional versions and components, see SINAMICS S120 drive system

η J m Irated I0 Irated

% kgm2 (lbf-in-s2) kg (lb) A A A Order No.

1PH8083-1.F...1PH8083-1.G...1PH8083-1.M...1PH8083-1.N...

80.983.286.986.4

0.0064 (0.06) 32 (70.6) 7.511.613.617

8121723

9181818

6SL3127-7TE21-0AA36SL3127-7TE21-8AA36SL3127-7TE21-8AA36SL3127-7TE21-8AA3

1PH8087-1.F...1PH8087-1.G...1PH8087-1.M...1PH8087-1.N...

81.785.387.186.8

0.0089 (0.08) 39 (86.0) 1014.117.319.5

11152328

18181830

6SL3127-7TE21-8AA36SL3127-7TE21-8AA36SL3127-7TE21-8AA36SL3127- 1 TE23-0AA3

1PH8101-1.F... 83.5 0.0138 (0.12) 42 (92.6) 12.5 14 18 6SL3127-7TE21-8AA3

1PH8103-1.D...1PH8103-1.F...1PH8103-1.G...1PH8103-1.M...

81.485.287.788.0

0.0172 (0.15) 51 (112) 1013.517.525.7

11141931

18181830


1PH8105-1.F... 86.7 0.0252 (0.22) 65 (143) 17.5 20 18 6SL3127-7TE21-8AA3

1PH8107-1.D...1PH8107-1.F...1PH8107-1.G...1PH8107-1.M...

83.486.989.788.0

0.0289 (0.26) 73 (161) 17.523.52638

25252948

18303045

6SL3127-7TE21-8AA36SL3127- 1 TE23-0AA36SL3127- 1 TE23-0AA36SL3127- 1 TE24-5AA3

1PH8131-1.F... 89.9 0.059 (0.52) 89 (196) 24 30 30 6SL3127- 1 TE23-0AA3

1PH8133-1.D...1PH8133-1.F...1PH8133-1.G...

87.189.991.9

0.076 (0.67) 106 (234) 303445

324254

304545

6SL3127- 1 TE23-0AA36SL3127- 1 TE24-5AA36SL3127- 1 TE24-5AA3

1PH8135-1.F... 89.8 0.094 (0.83) 125 (276) 43 53 45 6SL3127- 1 TE24-5AA3

1PH8137-1.D...1PH8137-1.F...1PH8137-1.G...

88.190.492.4

0.109 (0.96) 141 (311) 435660

476873

456060

6SL3127- 1 TE24-5AA36SL3127- 1 TE26-0AA36SL3127- 1 TE26-0AA3

Cooling:Internal air coolingExternal air cooling

01

Motor Module:Single Motor ModuleDouble Motor Module

12


© Siemens AG 2010

Asynchronous motorsMain spindle motors for SINAMICS S1201PH8 motors, standard typeSH 100/SH 132 – Forced ventilation

8/8 Siemens NC 61 · 2010

8



Rated Speed


Rated torque Static torque 1PH8 asynchronous motorStandard type

Y/Δ Y/Δ Y/Δ Y/Δ Y/Δ


3) nmax34) n2

5) Prated Mrated M0


Shaft height SH 100 – Forced ventilation – Star/delta connection – Line voltage 400 V 3 AC, operation on Active Line Module

2000/5000 9000 12000 18000 8950/10000 4.9/4.9 (6.57/6.57) 23/9 (17.0/6.64) 29/19 (21.4/14.0) 1PH8101-17S77-7771

9000 12000 18000 7650/10000 10/9.3 (13.4/12.5) 48/18 (35.4/13.3) 55/36 (40.6/26.6) 1PH8105-17S77-7771

9000 12000 18000 8550/10000 11/11 (14.8/14.8) 53/21 (39.1/15.5) 63/42 (46.5/31.0) 1PH8107-17S77-7771

Shaft height SH 132 – Forced ventilation – Star/delta connection – Line voltage 400 V 3 AC, operation on Active Line Module

2000/5000 8000 10000 15000 8000/10000 14.6/14.6 (19.6/19.6) 70/28 (51.6/20.7) 94/55 (69.3/40.6) 1PH8131-17S77-7771

8000 10000 15000 6500/10000 24.5/24.5 (32.9/32.9) 117/47 (86.3/34.7) 157/94 (116/69.3) 1PH8135-17S77-7771

8000 10000 15000 3000/6000 29/27.5 (38.9/36.9) 138/53 (102/39.1) 185/105 (136/77.4) 1PH8137-17S77-7771



© Siemens AG 2010


1PH8 motors, standard typeSH 100/SH 132 – Forced ventilation

8/9Siemens NC 61 · 2010

8




Weight, approx.6)


Static current




Y/Δ Y/Δ Y/Δ



1PH8101-1.S... 87.2/90.2 0.0138 (0.12) 42 (92.6) 13.2/13.5 15/20 18 6SL3127-7TE21-8AA3

1PH8105-1.S... 89.1/91.4 0.0252 (0.22) 65 (143) 23/24 25/34 30 6SL3127-1 TE23-0AA3

1PH8107-1.S... 89.4/90.9 0.0289 (0.26) 73 (161) 26.7/28 30/40 30 6SL3127-1 TE23-0AA3

1PH8131-1.S... 90.8/89.7 0.059 (0.52) 89 (196) 39/40 47/56 45 6SL3127-1 TE24-5AA3

1PH8135-1.S... 91.7/93.9 0.094 (0.83) 125 (276) 51/52 62/78 60 6SL3127-1 TE26-0AA3

1PH8137-1.S... 93.1/91.9 0.109 (0.96) 141 (311) 56/56 68/87 60 6SL3127-1 TE26-0AA3


01


12


© Siemens AG 2010

Asynchronous motorsMain spindle motors for SINAMICS S1201PH8 motors, standard typeSH 80 to SH 132 – Water cooling

8/10 Siemens NC 61 · 2010

8



Rated speed


Rated torque Static torque 1PH8 asynchronous motor Standard type


3) nmax34) n2

5) Prated Mrated M0


Shaft height SH 80 – Water cooling – Line voltage 400 V 3 AC, operation on Active Line Module

150020004500

100001000010000

120001500015000

–1600020000

48509150

18950

3.5 (4.69)4.3 (5.77)6.7 (8.98)

22 (16.2)21 (15.5)14 (10.3)

23 (17.0)23 (17.0)23 (17.0)

1PH8083-17 F2 7-77711PH8083-17G2 7-77711PH8083-17N2 7-7771

150020004500

100001000010000

150001500015000

–1900020000

77001000020000

4.6 (6.17)6.1 (8.18)8.5 (11.4)

29 (21.4)29 (21.4)18 (13.3)

34 (25.1)34 (25.1)27 (19.9)

1PH8087-17 F2 7-77711PH8087-17G2 7-77711PH8087-17N2 7-7771


2000 9000 12000 – 6800 6.4 (8.58) 31 (22.9) 34 (25.1) 1PH8101-17G2 7-7771

20003000

90009000

1200012000

–18000

530014600

9.5 (12.7)10.6 (14.2)

45 (33.2)34 (25.1)

48 (35.4)46 (33.9)

1PH8103-17G2 7-77711PH8103-17M27-7771

150020003000

900090009000

–1200012000

––18000

50006750

11700

11 (14.8)13 (17.4)16.8 (22.5)

70 (51.6)62 (45.7)53 (39.1)

74 (54.6)74 (54.6)71 (52.4)

1PH8105-17 F2 7-77711PH8105-17G2 7-77711PH8105-17M27-7771

15003000

90009000

1200012000

–18000

640018000

14 (18.8)18 (24.1)

89 (65.6)57 (42.0)

94 (69.3)175 (129)

1PH8107-17 F2 7-77711PH8107-17M27-7771


15002000

80008000

1000010000

1100014000

32005500

15 (20.1)18 (24.1)

96 (70.8)86 (63.4)

96 (70.8)101 (74.5)

1PH8131-17 F2 7-77711PH8131-17G2 7-7771

15002000

80008000

1000010000

1300015000

45007000

17 (22.8)22 (29.5)

108 (79.7)105 (77.4)

136 (100)134 (98.8)

1PH8133-17 F2 7-77711PH8133-17G2 7-7771

15002000

80008000

1000010000

1400015000

52505250

22 (29.5) 29 (38.9)

140 (103) 138 (102)

172 (127)170 (125)

1PH8135-17 F2 7-77711PH8135-17G2 7-7771

1500 8000 10000 15000 6500 27 (36.2) 172 (127) 202 (149) 1PH8137-17 F2 7-7771

1500 8000 10000 15000 7000 30 (40.2) 191 (141) 223 (164) 1PH8138-17 F2 7-7771



© Siemens AG 2010


1PH8 motors, standard typeSH 80 to SH 132 – Water cooling

8/11Siemens NC 61 · 2010

8




Weight, approx.6)


Static current






1PH8083-1.F2...1PH8083-1.G2...1PH8083-1.N2...

78.483.387.7

0.0064 (0.06) 36 (79.4) 8.912.018.0

91323

91818

6SL3127-7TE21-0AA36SL3127-7TE21-8AA36SL3127-7TE21-8AA3

1PH8087-1.F2...1PH8087-1.G2...1PH8087-1.N2...

81.484.389.1

0.0089 (0.08) 44 (97.0) 13.717.524.0

151931

181830

6SL3127-7TE21-8AA36SL3127-7TE21-8AA36SL3127- 1 TE23-0AA3

1PH8101-1.G2... 85.7 0.0138 (0.12) 51 (113) 16.8 18 18 6SL3127-7TE21-8AA3

1PH8103-1.G2...1PH8103-1.M2...

85.790.0

0.0172 (0.15) 60 (132) 2330

2435

3030

6SL3127-1 TE23-0AA36SL3127-1 TE23-0AA3

1PH8105-1.F2...1PH8105-1.G2...1PH8105-1.M2...

84.387.990.0

0.0252 (0.22) 74 (163) 28.534.545

293852

304545

6SL3127-1 TE23-0AA36SL3127-1 TE24-5AA36SL3127-1 TE24-5AA3

1PH8107-1.F2...1PH8107-1.M2...

82.990.0

0.0289 (0.26) 83 (183) 43.760

4473

4560

6SL3127-1 TE24-5AA36SL3127-1 TE26-0AA3

1PH8131-1.F2...1PH8131-1.G2...

88.390.8

0.059 (0.52) 105 (232) 3040

3044

3045

6SL3127-1 TE23-0AA36SL3127-1 TE24-5AA3

1PH8133-1.F2...1PH8133-1.G2...

89.790.9

0.076 (0.67) 123 (271) 3852

4561

4560

6SL3127-1 TE24-5AA36SL3127-1 TE26-0AA3

1PH8135-1.F2...1PH8135-1.G2...

90.192.4

0.094 (0.83) 141 (311) 5164

5873

6085

6SL3127-1 TE26-0AA36SL3127-1 TE28-5AA3

1PH8137-1.F2... 90.0 0.1090 (0.96) 157 (346) 67 73 85 6SL3127-1 TE28-5AA3

1PH8138-1.F2... 88.2 0.1090 (0.96) 160 (353) 80 88 85 6SL3127-1 TE28-5AA3


01


12


© Siemens AG 2010


8/12 Siemens NC 61 · 2010

8


The values in the selection and ordering data are applicable when using a Smart Line Module with 380 V 3 AC line connection. When using an Active Line Module, proceed according to 1PH8 Motors Configuration Manual.

Rated speed

Continuous speed, max. Rated power for duty type S1

Rated torque Static torque

1PH8 asynchronous motor Standard type


2) n23) Prated Mrated M0

rpm rpm rpm rpm kW (HP) Nm (lbf-ft) Nm (lbf-ft) Order No.

Shaft height SH 180 – Water cooling – Line voltage 380 V 3 AC, operation on Smart Line Module

400700

100015002500

50005000500050005000

75007500750075007500

15002500500050005000

17 (22.8)33 (44.3)47 (63)70 (93.9)95 (127)

406 (299)450 (332)449 (331)446 (329)363 (268)

406 (299)450 (332)449 (331)446 (329)363 (268)

1PH8184-17B27-77711PH8184-17C27-77711PH8184-17D27-77711PH8184-17 F 27-77711PH8184-17 L 27-7771

400700

100015002500

50005000500050005000

75007500750075007500

18003000500050005000

23 (30.8)43 (57.7)64 (85.8)93 (125)

120 (161)

549 (405)587 (433)611 (451)592 (437)458 (338)

549 (405)587 (433)611 (451)592 (437)458 (338)



400700

100015002500

45004500450045004500

55005500550055005500

14002100280035003200

36 (48.3)61 (81.8)89 (119)

119 (160)153 (205)

860 (634)832 (614)850 (627)758 (559)584 (431)

860 (634)832 (614)850 (627)758 (559)584 (431)


400700

100015002500

45004500450045004500

–––––

16002300240037003200

47 (63)81 (109)

115 (154)145 (194)185 (248)

1122 (828)1105 (815)1098 (810)

923 (681)707 (521)

1122 (828)1105 (815)1098 (810)923 (681)707 (521)


400700

100015002500

45004500450045004500

–––––

17002500230037003200

58 (77.8)96 (129)

141 (189)192 (257)226 (303)

1385 (1022)1310 (966)1347 (994)1222 (901)

863 (637)

1385 (1022)1310 (966)1347 (994)1222 (901)863 (637)



400700

10001500

3300330033003300

––––

2200220022002200

71 (95.2)123 (165)172 (231)227 (304)

1695 (1250)1678 (1238)1643 (1212)1445 (1066)

1695 (1250)1678 (1238)1643 (1212)1445 (1066)

1PH8284-17B27-77711PH8284-17C27-77711PH8284-17D27-77711PH8284-17 F 27-7771

400700

1000

330033003300

–––

220022002200

89 (119)153 (205)214 (287)

2125 (1567)2087 (1539)2044 (1508)

2125 (1567)2087 (1539)2044 (1508)

1PH8286-17B27-77711PH8286-17C27-77711PH8286-17D27-7771

400700

33003300

––

22002200

109 (146)188 (252)

2602 (1919)2565 (1892)

2602 (1919)2565 (1892)

1PH8288-17B27-77711PH8288-17C27-7771



© Siemens AG 2010



8/13Siemens NC 61 · 2010

8

1) Bearing version for standard. 2) Bearing version for performance. 3) Maximum permissible thermal speed at constant power or speed which is at the voltage limit when P = Prated.4) With the specified Motor Module, the motor cannot be fully utilized with M0.



Weight, approx.


Static current



For additional versions and components, see SINAMICS S120 drive system



1PH8184-1.B2...1PH8184-1.C2...1PH8184-1.D2...1PH8184-1.F2...1PH8184-1.L2...

83.187.290.492.994.5

0.50 (4.43) 340 (750) 5077

114150196

5077

114150196

6085

132200200

6SL3127-1 TE26-0AA36SL3127-1 TE28-5AA36SL3127-1 TE31-3AA36SL3127-1 TE32-0AA36SL3127-1 TE32-0AA3


84.589.892.093.594.8

0.65 (5.75) 410 (904) 6897

148198250

6897

148198250

85132200200260



85.891.493.795.196.1

1.45 (12.83) 610 (1345) 100128188240310

100128188240310

132132200260310



87.592.893.895.796.3

1.90 (16.82) 740 (1632) 130184235295380

130184235295380

132200260310380



88.693.094.395.996.4

2.35 (20.8) 870 (1918) 154210280390455

154210280390455

2002103103804)

490


1PH8284-1.B2...1PH8284-1.C2...1PH8284-1.D2...1PH8284-1.F2...

91.494.595.796.4

4.42 (39.1) 1280 (2822) 170260350445

170260350445

200260380490

6SL3127-1 TE32-0AA36SL3320-1 TE32-6AA36SL3320-1 TE33-8AA36SL3320-1 TE35-0AA3

1PH8286-1.B2...1PH8286-1.C2...1PH8286-1.D2...

91.694.896.0

5.42 (48.0) 1490 (3285) 210320460

210320460

210380490

6SL3320-1 TE32-1AA36SL3320-1 TE33-8AA36SL3320-1 TE35-0AA3

1PH8288-1.B2...1PH8288-1.C2...

92.595.2

6.61 (58.5) 1750 (3859) 260400

260400

260490

6SL3320-1 TE32-6AA36SL3320-1 TE35-0AA3

Format:Booksize Chassis

13


01

Motor Module:Single Motor Module 1


© Siemens AG 2010

Asynchronous motorsMain spindle motors for SINAMICS S1201PH8 motors, standard typeForced ventilation/water cooling

8/14 Siemens NC 61 · 2010

8

■ Order number supplement for shaft heights 80/100/132

1) Maximum speed nmax = 12000 rpm.2) Maximum speed nmax = 15000 rpm.3) Only possible if 14th data position: L, M.4) Not possible for motors with star/delta connection.5) For a definition of vibration magnitude according to Siemens, please see 1PH8 Motors Configuration Manual.6) With 1PH808/1PH810, only possible if 9th data position: L or V

With 1PH813, only possible if 9th data position: L, T, U or V7) With 1PH810, power connector is only possible up to a maximum static current of I0 = 36 A.

With 1PH813, power connector is only possible up to a maximum static current of I0 = 85 A.

Data position of the Order No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Shaft height 80 1 P H 8 0 8 . – 1 . – 1 – ZShaft height 100 1 P H 8 1 0 . – 1 . – 1 – ZShaft height 132 1 P H 8 1 3 . – 1 . – 1 – ZOverall lengthAsynchronous version without brake 1Encoder systems for motors without DRIVE-CLiQ interfaceWithout encoder AIncremental encoder sin/cos 1 Vpp 2048 S/R with C and D tracks (encoder IC2048S/R)1) MIncremental encoder sin/cos 1 Vpp 512 S/R without C and D tracks (encoder IN512S/R)2) TIncremental encoder sin/cos 1 Vpp 256 S/R without C and D tracks (encoder IN256S/R)3) LAbsolute encoder 2048 S/R single-turn, 4096 revolutions multi-turn, with EnDat interface (encoder AM2048S/R)1)

E

Encoder systems for motors with DRIVE-CLiQ interface4)

22 bit incremental encoder (resolution 4194304, internal 2048 S/R) + commutation position 11 bit (encoder IC22DQ)1)

D

20 bit incremental encoder (resolution 1048576, internal 512 S/R)2) without commutation position (encoder IN20DQ)

U

19 bit incremental encoder (resolution 524288, internal 256 S/R) without commutation position (encoder IN19DQ)3)

V

22 bit absolute encoder single-turn (resolution 4194304, internal 2048 S/R) with 12 bit multi-turn (traversing range 4096 revolutions) (encoder AM22DQ)1)

F

Rated speed (winding version)

CoolingForced ventilation DE NDE 0Forced ventilation NDE DE 1Water cooling 2Type of constructionIM B3 (IM V5, IM V6) 0IM B5 (IM V1, IM V3) 2IM B35 (IM V15, IM V35) (Only possible for 1PH810/1PH813) 3Shaft extension DE BalancingPlain shaft – 0Fitted key (Not possible if 14th data position: M) Full-key 1Fitted key (Not possible if 14th data position: M) Half-key 2Plain hollow shaft3) – 3Bearing version Vibration magnitude acc. to

Siemens5)/EN 60034-14Shaft and flange accuracy

Standard R/A R BStandard S/A R CStandard SR/A R DPerformance SPECIAL/B SPECIAL LHigh performance6) SPECIAL/B SPECIAL MAdvanced lifetime4) S/A R QPower connection (view of DE) Cable entry Signal connectionTerminal box top Right DE ATerminal box top Left DE BTerminal box top NDE Left CPower connector top4)7) Right DE EPower connector top4)7) Left DE FPower connector top4)7) NDE Left GPower connector top4)7) DE Right HVersion status 1Special version (order codes are required for options) Z


© Siemens AG 2010


1PH8 motors, standard typeForced ventilation/water cooling

8/15Siemens NC 61 · 2010

8

■ Order number supplement for shaft heights 180/225/280

1) Maximum speed nmax = 12000 rpm.2) With 1PH818, continuous speed nmax = 3000 min.

With 1PH822, continuous speed nmax = 2500 rpm. With 1PH828, continuous speed nmax = 2000 rpm.

3) For a definition of vibration magnitude according to Siemens, please see 1PH8 Motors Configuration Manual.4) Only possible with 1PH818/1PH8224.

With 1PH818, continuous speed nmax = 7500 rpm. With 1PH8224, continuous speed nmax = 5500 rpm.

Data position of the Order No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Shaft height 180 1 P H 8 1 8 . – 1 . 2 – 1 – ZShaft height 225 1 P H 8 2 2 . – 1 . 2 – 1 – ZShaft height 280 1 P H 8 2 8 . – 1 . 2 – 1 – ZOverall lengthAsynchronous version without brake 1Encoder systems for motors without DRIVE-CLiQ interfaceWithout encoder AIncremental encoder sin/cos 1 Vpp 2048 S/R with C and D tracks (encoder IC2048S/R)1) MAbsolute encoder 2048 S/R single-turn, 4096 revolutions multi-turn, with EnDat interface (encoder AM2048S/R)1)

E

Encoder systems for motors with DRIVE-CLiQ interface22 bit incremental encoder (resolution 4194304, internal 2048 S/R) + commutation position 11 bit (encoder IC22DQ)1)

D

22 bit absolute encoder single-turn (resolution 4194304, internal 2048 S/R) with 12 bit multi-turn (traversing range 4096 revolutions) (encoder AM22DQ)1)

F

Rated speed (winding version)

CoolingWater cooling 2Type of constructionIM B3 (IM B6, IM B7, IM B8, IM V6) (IM B6/IM B7/IM B8 not possible for 1PH828) 0IM V5 1IM B5 (IM V3)2) (Not possible if 14th data position: L) 2IM B35 (IM V35) 3IM V15 5Shaft extension DE BalancingPlain shaft – 0Fitted key Full-key 1Fitted key Half-key 2Bearing version Vibration magnitude acc. to

Siemens3)/EN 60034-14Shaft and flange accuracy

Standard R/A R BStandard (Only for 1PH818/1PH822) S/A R CStandard (Only for 1PH818/1PH822) SR/A R DIncreased radial forces R/A R FPerformance4) (Not possible if 12th data position: 2) SR/A R LPower connection (view of DE) Cable entry Signal connectionTerminal box top Right DE ATerminal box top Left DE BTerminal box top NDE Right CTerminal box top DE Right DVersion status 1Special version (order codes are required for options) Z


© Siemens AG 2010

Asynchronous motorsMain spindle motors for SINAMICS S1201PH8 motors, standard typeForced ventilation/water cooling

8/16 Siemens NC 61 · 2010

8

■ Options

1) With options K09 or K10, another terminal box type is used for side mounting. gk823 is used instead of gk813. gk843 is used instead of gk833. Only possible for types of construction IM B3 or IM B35.

2) Only appropriate if oil spray or oil vapor is occasionally deposited on the sealing ring. 3) Only possible in conjunction with option K09 or K10.

Order code

Description of option Used with motorsWhen ordering a motor with options, -Z should be added to the order number. The order code should also be specified for each additional required option.Order codes must not be repeated in plain text in the order.

1PH8081PH8101PH813

1PH8181PH8221PH828

A12 Additional PTC thermistor chain for alarm and tripping(Only possible for versions with terminal box.)

✔ ✔

K08 Encoder connector mounted opposite – ✔

K09 Terminal box or power connector NDE right ✔ –(For terminal box type, see Selection guides or CAD CREATOR) 1)

Only with 1PH810/1PH813

Terminal box NDE right, cable entry DE/signal connection top(Only possible if 15th data position: A)

– ✔

K10 Terminal box or power connector NDE left ✔ –(For terminal box type, see Selection guides or CAD CREATOR) 1)

Only with 1PH810/1PH813

Terminal box NDE left, cable entry DE/signal connection top(Only possible if 15th data position: A)

– ✔

K18 Radial shaft sealing ring DE2) (Not possible if 14th data position: F, L or M) ✔ ✔

K40 Regreasing system DE and NDE (standard with 1PH828) – ✔

K83 Terminal box3) rotated through + 90° – ✔

K84 Terminal box3) rotated through - 90° – ✔

K85 Terminal box3) rotated through + 180° – ✔

K90 Version with flange size A400 (Only possible if 12th data position: 2, 3 or 5) – ✔With 1PH818 only

V90 1PH7-compatible shaft extension (d × l: 42 mm × 110 mm (1.65 in × 4.33 in)) ✔ –(Note reduced radial forces) With 1PH813 only

L00 Replace terminal box (standard) with the next largest terminal box(Note dimension implications in CAD CREATOR.)

– ✔

P00 Undrilled cable entry plate – ✔

P01 Cable entry plate 3 × M63 × 1.5 (Only with terminal box type 1XB7700-P02/1XB7712-P03) – ✔

P02 Cable entry plate 3 × M75 × 1.5 (Only with terminal box type 1XB7712-P03) – ✔

P04 Cable entry plate 4 × M63 × 1.5 (Only with terminal box type 1XB7712-P03) – ✔

L74 Fan in IP66 degree of protection ✔ –Paint finish (Anthracite RAL 7016) Standard Standard

X01 Normal paint finish: Jet black RAL 9005 ✔ ✔

X02 Normal paint finish: Cream white RAL 9001 ✔ ✔

X03 Normal paint finish: Reseda green RAL 6011 ✔ ✔

X04 Normal paint finish: Pebble gray RAL 7032 ✔ ✔

X05 Normal paint finish: Sky blue RAL 5015 ✔ ✔

X06 Normal paint finish: Light ivory RAL 1015 ✔ ✔

X08 Normal paint finish: White aluminum RAL 9006 ✔ ✔

K24 Primer ✔ ✔

Pale green Red brown

K23 Special paint finish worldwide: Primer and paint finish in anthracite RAL 7016 ✔ ✔

K23+X.. Special paint finish worldwide: Primer and paint finish can be selected from X01 to X08 ✔ ✔

NC61_en_Kap08_02.fm Seite 16 Freitag, 15. Januar 2010 7:50 07

© Siemens AG 2010


1PH8 motors, standard typeForced ventilation/water cooling

8/17Siemens NC 61 · 2010

8

■ Terminal box assignment, max. connectable conductor cross-sections

For terminal box type 1XB7, other cable entries can be ordered for the power depending on the standard, see options.

■ Ordering example

1) Dependent on the design of the metric cable gland. 2) Current carrying capacity based on EN 60204-1 and IEC 60364-5-52

according to installation type C.3) Hole with Ø 22 mm (0.87 in), 90 ° to signal connection4) Arranged opposite of signal connection (sideways from cable entry plate).

5) Standard for motors with rated currents less than 210 A.6) Standard for motors with rated currents greater than 210 A to 270 A.7) Standard for motors with rated currents greater than 270 A to 700 A.

1PH8 motor Terminal box Cable entry Outer cable diameter, max.1)

Number of main terminals Cross-section per terminal, max.

Rated current, max.2)

Type Type Power External signals

mm mm² A

1PH808 Forced ventilation/Water cooling

gk803 1 × M25 × 1.5 1 × Ø 22 mm3) 20 Phases: 3 × M5Grounding: 2 × M5

1 × 10 50

1PH810 Forced ventilation gk813 1 × M32 × 1.5 1 × Ø 22 mm3) 24.2 Phases: 3 × M5Grounding: 2 × M5

1 × 16 66

Water cooling/forced ventilation with hollow shaft with options K09 or K10

gk823 1 × M32 × 1.5 1 × Ø 22 mm3) 24.2 Phases: 3 × M5Grounding: 2 × M5

1 × 16 66

Star/delta gk826 1 × M32 × 1.5 1 × Ø 22 mm3) 24.2 Phases: 6 × M5Grounding: 2 × M5

1 × 10 50

1PH813 Forced ventilation gk833 1 × M40 × 1.5 1 × Ø 22 mm3) 32 Phases: 3 × M6Grounding: 2 × M6

1 × 35 104

Water cooling/forced ventilation with hollow shaft with options K09 or K10

gk843 1 × M50 × 1.5 1 × Ø 22 mm3) 38 Phases: 3 × M6Grounding: 2 × M6

1 × 50 125

Star/delta gk846 1 × M50 × 1.5 1 × Ø 22 mm3) 38 Phases: 6 × M6Grounding: 2 × M6

1 × 25 84

1PH8181PH8221PH828

1XB7322-P055)

2 × M50 × 1.5 1 × PG 13.54) 38 Phases: 3 × M12Grounding: 2 × fixing eyelet

2 × 50 210

1XB7422-P066)

2 × M63 × 1.5 1 × PG 13.54) 53 Phases: 3 × M12Grounding: 2 × fixing eyelet

2 × 70 270

1XB7700-P027)

2 × M75 × 1.5 1 × PG 13.54) 68 Phases: 3 × 2 × M12Grounding: 2 × fixing eyelet

3 × 150 700

1PH828 (option) 1XB7712-P03 3 × M75 × 1.5 1 × PG 13.54) 68 Phases: 3 × 4 × M16Grounding: 4 × M16

4 × 185 1150

Selection criteria Version Structure of the order number

1PH8 motor Shaft height 80Rated power 3.5 kWVersion status 1

1PH8083-. . . . . - . . . 1

Asynchronous version without brake 1PH8083-1 . . . . - . . .1Encoder system Incremental encoder sin/cos 1 Vpp 2048 S/R with C and D tracks (encoder IC2048S/R) 1PH8083-1M . . .- . . .1Rated speed 1500 rpm 1PH8083-1MF . .- . . .1Cooling Water cooling 1PH8083-1MF2 .- . . .1Type of construction IM B3 (IM V5, IM V6) 1PH8083-1MF20- . . .1Shaft extension DE Plain shaft 1PH8083-1MF20-0 . .1Bearing version Standard

Vibration magnitude R/AShaft and flange accuracy R

1PH8083-1MF20-0B .1

Connection Power connection terminal box topCable entry rightSignal connection DE

1PH8083-1MF20-0BA1

Options 1PH8083-1MF20-0BA1-Z

Additional PTC thermistor chain for alarm and tripping1PH8083-1MF20-0BA1-ZA12

Special paint finish worldwide: Primer and paint finish sky blue RAL 50151PH8083-1MF20-0BA1-ZA12 K23 X05


© Siemens AG 2010


1PH7 motors

8/18 Siemens NC 61 · 2010

8

■ Overview

1PH7 motors (SH 100 to SH 160 and SH 180/SH 225)

Air-cooled 1PH7 motors are rugged and low-maintenance 4-pole asynchronous motors with squirrel-cage rotors.

A fan for providing forced ventilation is mounted axially on the rear of the motor. The normal direction of air flow is from the drive end (DE) to the non-drive end (NDE) in order to keep the exhaust heat of the motor away from the machine. The reverse direction of air flow can be ordered as an option.

The motors are equipped with a built-in encoder system for sensing the motor speed and indirect position. In machine tools, the encoder system is capable of C-axis operation as standard – that is, an additional encoder is not required for C-axis operation.

■ Benefits7 Short overall length of motor7 Minimal overall dimension thanks to the integrated terminal

box (SH 100 to SH 160)7 Maximum speeds of up to 9000 rpm (optional: 12000 rpm)7 Full rated torque is continuously available, even at standstill7 Optimum matching to the SINAMICS S120 power levels

■ Application• Small, compact machine tools • Complex machining centers and turning machines• Special machines• Printing industry:

- Single drives for printing units• Rubber, plastic, wire, and glass manufacturing:

- Drives for extruders, calenders, rubber injection machines, film machines, fleece machines

- Wire-drawing machines, wire-stranding machines, etc.• General applications such as coiler and winder drives

1) The sound pressure level can be reduced if the fan is operated on a 60 Hz supply system with option K44.

2) The sound pressure level can be reduced if the air flow is from the drive end to the non-drive end with option G15.

3) For type of construction, see Selection guides.4) DE is the drive end with shaft. NDE is the non-drive end.5) For maximum permissible load, see the 1PH7 Motors Configuration Manual.6) Shaft extension run-out, concentricity of centering ring and shaft, and

perpendicularity of flange to shaft.

■ Technical specifications (general)

■ Technical specifications (core type)


Product name 1PH7 motorCoolant temperature, permissible - 15 ... + 40 °C (+ 5 ... + 104 °F)Temperature monitoring KTY 84 temperature sensor in

stator winding Insulation of the stator winding in accordance with EN 60034-1 (IEC 60034-1)

Temperature class 155 (F) for a coolant temperature of up to 40 °C (104 °F)

Motor fan ratings 400 V 3 AC ±10 %, 50 Hz/60 Hz480 V 3 AC + 5 %/-10 %, 60 Hz

Encoder system, built-in• Without DRIVE-CLiQ interface • Incremental encoder sin/cos

1 Vpp 2048 S/R without C and D tracks (encoder IN2048S/R)

• Incremental encoder sin/cos 1 Vpp 2048 S/R with C and D tracks (encoder IC2048S/R)

• Absolute encoder EnDat 2048 S/R single-turn, 4096 revolutions multi-turn, with EnDat interface (encoder AM2048S/R)

• With DRIVE-CLiQ interface • 22 bit incremental encoder (resolution 4194304, 2048 S/R internal) + 11 bit commutation position (encoder IC22DQ)

• 22 bit incremental encoder (resolution 4194304, 2048 S/R internal) without commutation position (encoder IN22DQ)

• 22 bit absolute encoder single-turn (resolution 4194304, 2048 S/R internal) + 12 bit multi-turn (traversing range 4096 rev-olutions) (encoder AM22DQ)

Type of construction in accordance withEN 60034-7 (IEC 60034-7)

IM B3IM B35IM B5 (only SH 100 and SH 132)

Sound pressure level LpA (1 m) in accordance with EN ISO 1680Tolerance + 3 dB

From DE to NDE (with the fan operating on a 50 Hz supply system)

• 1PH710/1PH713• 1PH716• 1PH718• 1PH722

70 dB75 dB1)

73 dB2)

76 dB2)

Terminal box connection type• Motor/fan Terminals in terminal box • Encoder system and

PTC thermistor17-pin circular socket(without mating connector) or DRIVE-CLiQ

Rating plate 1 supplied separately with terminal box


Type of construction in acc. with EN 60034-7 (IEC 60034-7)3)

• 1PH710/1PH713• 1PH716

IM B5 (IM V1, IM V3)IIM B35 (IM V15, IM V35)

Terminal box locationView DE4)

Top, cable entry from right

Bearing version on DE5) Bearing for belt or coupling output

Vibration magnitude in accordance withEN 60034-14 (IEC 60034-14)

Grade S


Tolerance R (reduced)


Motor IP55, fan IP54

Paint finish UnpaintedOptional: anthracite


© Siemens AG 2010


1PH7 motors

8/19Siemens NC 61 · 2010

8


Typical speed/power graph for AC motors1)

The graph shows the typical relationship between motor speed and drive power in 1PH7 motors for the following duty types in accordance with IEC 60034-1:

S1: Continuous duty

S6: Continuous duty with intermittent loading and a relative duty factor of 60 % (S6-60 %) or 40 % (S6-40 %) with a maximum duty cycle time of 10 minutes.

S2: Short-time duty with duty period of 30 min (S2-30 min) and subsequent standstill.


2) Values taken from the speed/power graph when using an Active Line Mod-ule on a 400 V 3 AC supply system. It you are using a Smart Line Module, proceed in accordance with the 1PH7 Motors Configuration Manual.

S2-30 min

S6-60 %

S1

00

n2S6-40 %

n2S2-30 min

n2S6-60 %

PS6-40 %

n2S1 G

_NC

01_E

N_0

0015

b

Motor power

Speed

Voltage limit

nratednmax

1PH7 motor Rated speed

Attainable speed for rated power in duty type

Type nrated n22)

S1 S6-60 % S6-40 % S2-30 min

rpm rpm rpm rpm rpm

1PH7101-..F 1500 8200 7000 6000 6500

1PH7103-..D1PH7103-..F1PH7103-..G

100015002000

375050009000

375046007500

310039006400

335045006900

1PH7105-..F 1500 7900 6750 5750 6150

1PH7107-..D1PH7107-..F1PH7107-..G

100015002000

580065007000

480062007000

410052506900

465056507000

1PH7131-..F 1500 6700 5500 4500 5000

1PH7133-..D1PH7133-..F1PH7133-..G

100015002000

470068006500

370056006500

280045005900

345051006450

1PH7135-..F 1500 7500 6200 5200 5650

1PH7137-..D1PH7137-..F1PH7137-..G

100015002000

540070006000

450070006000

360062005800

410068006000

1PH7163-..B1PH7163-..D1PH7163-..F1PH7163-..G

500100015002000

2500580055003500

1900480055003500

1500400055003500

1730440055003500

1PH7167-..B1PH7167-..D1PH7167-..F1PH7167-..G

500100015002000

2100625045003250

1600520045003250

1250430045003250

1400470045003250

1PH7184-..T1PH7184-..D1PH7184-..E1PH7184-..F1PH7184-..L

5001000125015002500

45005000500050005000

38004400468050005000

33503600419050005000

33503600360050005000

1PH7186-..T1PH7186-..D1PH7186-..E

50010001250

480050005000

410046504260

358038503780

400038503580

1PH7224-..C1PH7224-..D1PH7224-..F

70010001500

302045004500

257045004330

229041004000

217037303890


© Siemens AG 2010

Asynchronous motorsMain spindle motors for SINAMICS S1201PH7 motors, core type SH 100 to SH 160 – Forced ventilation

8/20 Siemens NC 61 · 2010

8


To select the type of construction and degree of protection, see Selection guides.

Shaftheight

Rated speed

Continuous speed, max.

Speed, max.1) Rated power for duty type

1PH7 asynchronous motorwith solid shaftCore type

SH nrated nS1 cont.2) nS1 cont.

3) nmax nmax4) Prated

S1 S6-60 % S6-40 % S2-30 min

rpm rpm rpm rpm rpm kW(HP)

kW(HP)

kW(HP)

kW(HP)

Order No.

Forced ventilation – Line voltage 400 V 3 AC, operation on Active Line Module

100 2000 5500 – 9000 – 7 (9.39) 8.5 (11.4) 10 (13.4) 9.25 (12.4) 1PH7103-7 7G02-0C7 7

1500 5500 – 9000 – 9 (12.1) 11 (14.8) 13 (17.4) 12 (16.1) 1PH7107-7 7 F02-0C7 7

132 10002000

4500 – 8000 – 12 (16.1)20 (26.8)

15 (20.1)25 (33.5)

18.5 (24.8)30 (40.2)

16 (21.5)27.5 (36.9)

1PH7133-7 7D02-0C7 71PH7133-7 7G02-0C7 7

10002000

4500 – 8000 – 17 (22.8)28 (37.6)

20.5 (27.5)35 (46.9)

25 (33.5)43 (57.7)

22.5 (30.2)39 (52.3)

1PH7137-7 7D02-0C7 71PH7137-7 7G02-0C7 7

160 10001500

3700 – 6500 – 22 (29.5)30 (40.2)

27 (36.2)37 (49.6)

33 (44.3)45 (60.4)

30 (40.2)41 (55.0)

1PH7163-7 7D03-0C7 71PH7163-7 7 F03-0C7 7

1500 3700 – 6500 – 37 (49.6) 46 (61.7) 56 (75.1) 51 (68.4) 1PH7167-7 7 F03-0C7 7

Fans: External fan unit, heavy-gauge threaded cable entry in terminal boxExternal fan unit, metric cable entry in terminal box

27

Encoder systems for motors without DRIVE-CLiQ interface:

Incremental encoder sin/cos 1 Vpp 2048 S/R without C and D tracks(encoder IN2048S/R)

Encoder systems for motors with DRIVE-CLiQ interface:

22 bit incremental encoder(encoder IN22DQ)

Q

Type of construction:5) IM B5 (IM V1, IM V3)IM B35 (IM V15, IM V35)6)

Shaft extension DE:5)

Fitted keyPlain shaft

Balancing:Half-key–

Direction of air flow (fan):DE → NDEDE → NDE

Blow-out direction:AxialAxial

Degree of protection:IP55, fan IP54IP55, fan IP54

Paint finish:UnpaintedAnthracite

N

23

AJ

03


© Siemens AG 2010


1PH7 motors, core typeSH 100 to SH 160 – Forced ventilation

8/21Siemens NC 61 · 2010

8

1PH7 motor (SH 100 to SH 160)

1) For continuous duty with 30 % nmax, 60 % 2/3 nmax, 10 % standstill for a duty cycle time of 10 min. For maintenance intervals for motors and components, see the 1PH7 Motors Configuration Manual.

2) Bearing version for coupling/belt output.3) Bearing version for increased maximum speed.4) Version for increased maximum speed only possible with vibration magnitude grade SR. The following options are not possible:

• Shaft seal.5) For preconditions for gearbox mounting, please refer to Gearboxes.6) Motors of shaft height 160 and higher require foot support.


Ratedtorque

Moment of inertia

Weight, approx.

Rated current for duty type




Mrated J m Irated Irated

S1 S6-60 % S6-40 % S2-30 min

Nm (lbf-ft)

kgm2 (lbf-in-s2)

kg(lb)

A A A A A Order No.

1PH7103-..G02-... 33.4 (24.6) 0.017 (0.15) 43 (94.8) 17.5 20.5 23.5 21.5 18 6SL3127-7TE21-8AA3

1PH7107-..F02-... 57.3 (43.3) 0.029 (0.26) 64 (141) 23.5 27.5 31 29 30 6SL3127-1TE23-0AA3

1PH7133-..D02-...1PH7133-..G02-...

114.6 (84.5)95.5 (70.4)

0.076 (0.67) 102 (225) 3045

3654

4363

37.559

3045

6SL3127-1TE23-0AA36SL3127-1TE24-5AA3

1PH7137-..D02-...1PH7137-..G02-...

162.3 (119.7)133.7 (98.6)

0.109 (0.96) 129 (284) 4360

5073

6087

5480

4560

6SL3127-1TE24-5AA36SL3127-1TE26-0AA3

1PH7163-..D03-...1PH7163-..F03-...

210.1 (155)191.0 (141)

0.19 (1.68) 198 (437) 5572

6586

77102

7194

6085

6SL3127-1TE26-0AA36SL3127-1TE28-5AA3

1PH7167-..F03-... 235.5 (174) 0.23 (2.04) 231 (509) 82 97 115 104 85 6SL3127-1TE28-5AA3


01


12


© Siemens AG 2010

Asynchronous motorsMain spindle motors for SINAMICS S1201PH7 motors, standard typeSH 100 – Forced ventilation

8/22 Siemens NC 61 · 2010

8



Shaftheight

Rated speed



1PH7 asynchronous motorwith solid shaftStandard type



S1 S6-60 % S6-40 % S2-30 min


kW(HP)

kW(HP)

kW(HP)

Order No.


100 1500 5500 10000 9000 12000 3.7 (4.96) 4.5 (6.03) 5.25 (7.04) 4.9 (6.57) 1PH7101-7 7 F 7 7-07 7 7

100015002000

5500 10000 9000 12000 3.7 (4.96)5.5 (7.38)7 (9.39)

4.5 (6.03)6.7 (8.98)8.5 (11.4)

5.25 (7.04)7.7 (10.3)

10 (13.4)

4.7 (6.30)7 (9.39)9.25 (12.4)

1PH7103-7 7 D7 7-07 7 71PH7103-7 7 F 7 7-07 7 71PH7103-7 7G7 7-07 7 7

1500 5500 10000 9000 12000 7 (9.39) 8.5 (11.4) 10 (13.4) 9.25 (12.4) 1PH7105-7 7 F 7 7-07 7 7

100015002000

5500 10000 9000 12000 6.25 (8.38)9 (12.1)

10.5 (14.1)

7.5 (10.1)11 (14.8)12.5 (16.8)

8.8 (11.8)13 (17.4)14.5 (19.4)

7.75 (10.4)12 (16.1)13.5 (18.1)

1PH7107-7 7D7 7-07 7 71PH7107-7 7 F 7 7-07 7 71PH7107-7 7G7 7-07 7 7


27


Absolute encoder EnDat 2048 S/R (encoder AM2048S/R)Incremental encoder sin/cos 1 Vpp 2048 S/R with C and D tracks (encoder IC2048S/R)Incremental encoder sin/cos 1 Vpp 2048 S/R (encoder IN2048S/R)


22 bit absolute encoder single-turn +12 bit multi-turn (encoder AM22DQ)22 bit incremental encoder + commutation position (encoder IC22DQ)22 bit incremental encoder (encoder IN22DQ)

FDQ

Terminal box/cable entry:

Top/from rightTop/from NDETop/from left

Type of construction:5) IM B3 (IM V5, IM V6)IM B5 (IM V1, IM V3)IM B35 (IM V15, IM V35)

Bearing version for:Coupling/belt outputCoupling/belt outputCoupling/belt outputIncreased speed (coupling/belt output)

Vibration magnitude:Grade RGrade SGrade SRGrade SR

Shaft and flange accuracy:Tolerance RTolerance RTolerance RTolerance R


Fitted keyFitted keyFitted keyFitted keyPlain shaftPlain shaft

Balancing:Half-keyHalf-keyFull-keyFull-key––

Direction of air flow (fan):DE → NDENDE → DEDE → NDENDE → DEDE → NDENDE → DE

Blow-out direction:AxialAxialAxialAxialAxialAxial

Degree of protection:IP55, fan IP54IP55, fan IP54IP55, fan IP54IP55, fan IP54IP55, fan IP54IP55, fan IP54

Seal:–DE flange with shaft sealing ring6)

–DE flange with shaft sealing ring6)


Paint finish:UnpaintedUnpaintedAnthraciteAnthraciteAnthracite, two coats Anthracite, two coats

EMN

023

023

BCDL

ABCDJK

023568


© Siemens AG 2010


1PH7 motors, standard typeSH 100 – Forced ventilation

8/23Siemens NC 61 · 2010

8




• Shaft sealing ring.5) For preconditions for gearbox mounting, please refer to Gearboxes.6) Only appropriate if the sealing ring is occasionally lubricated with oil spray/mist. A sealing ring is not possible with increased maximum speed.


Ratedtorque

Moment of inertia

Weight, approx.






S1 S6-60 % S6-40 % S2-30 min

Nm (lbf-ft)

kgm2 (lbf-in-s2)

kg(lb)

A A A A A Order No.

1PH7101-..F... 23.6 (17.4) 0.017 (0.15) 43 (94.8) 10 11.5 12.5 12 18 6SL3127-7TE21-8AA3

1PH7103-..D...1PH7103-.. F...1PH7103-..G...

35.3 (26.0)35.0 (25.8)33.4 (24.6)

0.017 (0.15) 43 (94.8) 101317.5

11.51620.5

131823.5

1216.521.5

181818


1PH7105-.. F... 44.6 (32.9) 0.029 (0.26) 64 (141) 17.5 21 23.5 22 18 6SL3127-7TE21-8AA3

1PH7107-..D...1PH7107-.. F...1PH7107-..G...

59.7 (44.0)57.3 (43.3)50.1 (37.0)

0.029 (0.26) 64 (141) 17.523.526

20.527.528.5

233133

212931

183030

6SL3127-7TE21-8AA36SL3127-1 TE23-0AA36SL3127-1TE23-0AA3


01


12


© Siemens AG 2010

Asynchronous motorsMain spindle motors for SINAMICS S1201PH7 motors, standard type SH 132 – Forced ventilation

8/24 Siemens NC 61 · 2010

8



Shaftheight

Rated speed






S1 S6-60 % S6-40 % S2-30 min


kW(HP)

kW(HP)

kW(HP)

Order No.


132 1500 4500 8500 8000 10000 11 (14.8) 13.5 (18.1) 16.5 (22.1) 15 (20.1) 1PH7131-7 7F7 7-07 7 7

100015002000

4500 8500 8000 10000 12 (16.1)15 (20.1)20 (26.8)

15 (20.1)18.5 (24.8)25 (33.5)

18.5 (24.8)23 (30.8)30 (40.2)

16 (21.5)20.5 (27.5)27.5 (36.9)

1PH7133-7 7D7 7-07 7 71PH7133-7 7F7 7-07 7 71PH7133-7 7G7 7-07 7 7

1500 4500 8500 8000 10000 18.5 (24.8) 23 (30.8) 28 (37.6) 25.5 (34.2) 1PH7135-7 7F7 7-07 7 7

100015002000

4500 8500 8000 10000 17 (22.8)22 (29.5)28 (37.6)

20.5 (27.5)27.5 (36.9)35 (46.9)

25 (33.5)33 (44.3)43 (57.7)

22.5 (30.2)30 (40.2)39 (52.3)

1PH7137-7 7D7 7-07 7 71PH7137-7 7F7 7-07 7 71PH7137-7 7G7 7-07 7 7


27





FDQ



Type of construction:5) IM B3 (IM V5, IM V6)IM B5 (IM V1, IM V3)IM B35 (IM V15, IM V35)














EMN

023

023

BCDL

ABCDJK

023568


© Siemens AG 2010



8/25Siemens NC 61 · 2010

8

1PH7 motors (SH 100 to SH 160)



• Shaft sealing ring.5) For preconditions for gearbox mounting, please refer to Gearboxes.6) Only appropriate if the sealing ring is occasionally lubricated with oil spray/mist. A sealing ring is not possible with increased maximum speed.


Ratedtorque

Moment of inertia

Weight, approx.






S1 S6-60 % S6-40 % S2-30 min

Nm (lbf-ft)

kgm2 (lbf-in-s2)

kg(lb)

A A A A A Order No.

1PH7131-..F... 70.0 (51.6) 0.076 (0.67) 102 (225) 24 29 34 31.5 30 6SL3127-1TE23-0AA3

1PH7133-..D...1PH7133-..F...1PH7133-..G...

114.6 (84.5)95.5 (70.4)95.5 (70.4)

0.076 (0.67) 102 (225) 303445

364154

434963

37.543.559

304545


1PH7135-..F... 117.8 (86.9) 0.109 (0.96) 129 (284) 42 50 58 54 45 6SL3127-1TE24-5AA3

1PH7137-..D...1PH7137-..F...1PH7137-..G...

162.3 (119.7)140.1 (103.3)133.7 (98.6)

0.109 (0.96) 129 (284) 435760

506873

607987

547380

456060



01



© Siemens AG 2010


8/26 Siemens NC 61 · 2010

8


To select the type of construction and degree of protection, see Selection guides

Shaftheight

Rated speed






S1 S6-60 % S6-40 % S2-30 min


kW(HP)

kW(HP)

kW(HP)

Order No.


160 500100015002000

3700 7000 6500 8000 12 (16.1)22 (29.5)30 (40.2)36 (48.3)

15 (20.1)27 (36.2)37 (49.6)44 (59.0)

18 (24.1)33 (44.3)45 (60.4)52 (69.7)

16.5 (22.1)30 (40.2)41 (55.0)48 (64.4)

1PH7163-7 7B7 7-07 7 71PH7163-7 7D7 7-07 7 71PH7163-7 7F 7 7-07 7 71PH7163-7 7G7 7-07 7 7

500100015002000

3700 7000 6500 8000 16 (21.5)28 (37.5)37 (49.6)41 (55.0)

19.5 (26.1)34.5 (46.3)46 (61.7)51 (68.4)

24 (32.2)42 (56.3)56 (75.1)61 (81.8)

21.5 (28.8)38 (51.0)51 (68.4)56 (75.1)

1PH7167-7 7B7 7-07 7 71PH7167-7 7D7 7-07 7 71PH7167-7 7F 7 7-07 7 71PH7167-7 7G7 7-07 7 7


27





FDQ



Type of construction:5) IM B3 (IM V5, IM V6)IM B35 (IM V15, IM V35)7)














EMN

023

03

BCDL

ABCDJK

023568


© Siemens AG 2010



8/27Siemens NC 61 · 2010

8




• Shaft sealing ring.5) For preconditions for gearbox mounting, please refer to Gearboxes.6) Only appropriate if the sealing ring is occasionally lubricated with oil spray/mist. A sealing ring is not possible with increased maximum speed.7) Motors of shaft height 160 and higher require foot support.


Ratedtorque

Moment of inertia

Weight, approx.






S1 S6-60 % S6-40 % S2-30 min

Nm (lbf-ft)

kgm2 (lbf-in-s2)

kg(lb)

A A A A A Order No.

1PH7163-..B...1PH7163-..D...1PH7163-..F...1PH7163-..G...

229.2 (169)210.1 (155)191.0 (141)171.9 (127)

0.19 (1.68) 198 (437) 30557285

366586

100

4277

102114

397194

107

30608585

6SL3127 -1TE23-0AA36SL3127 -1TE26-0AA36SL3127 -1TE28-5AA36SL3127 -1TE28-5AA3

1PH7167-..B...1PH7167-..D...1PH7167-..F...1PH7167-..G...

305.5 (225)267.4 (197)235.5 (174)195.8 (144)

0.23 (2.04) 231 (509) 37718289

448597

106

53100115124

4892

104115

458585

132

6SL3127 -1TE24-5AA36SL3127 -1TE28-5AA36SL3127 -1TE28-5AA36SL3127 -1TE31-3AA3


01



© Siemens AG 2010


8/28 Siemens NC 61 · 2010

8


To select the type of construction and degree of protection, see Selection guides

Shaftheight

Rated speed

Continuous speed, max. Speed, max.1)

Rated power for duty type



3) nS1 cont.4) nmax nmax

5) Prated

S1 S6-60 % S6-40 % S2-30 minrpm rpm rpm rpm rpm rpm kW

(HP)kW(HP)

kW(HP)

kW(HP)

Order No.

Forced ventilation – Line voltage 400 V 3 AC, operation on Active Line Module180 500

1000125015002500

3500 3000 4500 5000 7000 21.5 (28.8)39 (52.3)40 (53.6)51 (68.4)78 (105)

26.5 (35.5)48 (64.4)50 (67.1)68 (91.2)97 (130)

30.5 (40.9)58 (77.8)56 (75.1)81 (109)

115 (154)

30 (40.2)58 (77.8)66 (88.5)81 (109)

115 (154)

1PH7184-7 7T7 7-07 7 71PH7184-7 7D7 7-07 7 71PH7184-7 7E7 7-07 7 71PH7184-7 7F7 7-07 7 71PH7184-7 7L7 7-07 7 7

5001000125015002500

3500 3000 4500 5000 7000 29.6 (39.7)51 (68.4)60 (80.5)74 (99.2)

106 (142)

36.5 (48.9)65 (87.2)71 (95.2)94 (126)

131 (176)

43 (57.7)77 (103)80 (107)

113 (152)157 (211)

38 (51.0)77 (103)84 (113)

113 (152)165 (221)

1PH7186-7 7T7 7-07 7 71PH7186-7 7D7 7-07 7 71PH7186-7 7E7 7-07 7 71PH7186-7 7F7 7-07 7 71PH7186-7 7L7 7-07 7 7


27





FDQ


Top/from rightTop/from DETop/from NDETop/from left

Type of construction: IM B3IM B3 (IM V5, IM V6) (hoisting system for vertical types of construction)IM B359) IM B35 (Only for 1PH7184 with 450 mm (17.7 in) flange)9)

IM B35 (IM V15, IM V35) (hoisting system for vertical types of construction)9)

IM B35 (IM V15, IM V35) (Only for 1PH7184 with 450 mm (17.7 in) flange)9)

Bearing version for: Vibration magnitude: Shaft and flange accuracy:Coupling output Coupling outputCoupling output Coupling outputBelt outputBelt outputIncreased cantilever force (belt output)Increased cantilever force (belt output)Increased speed (coupling output)

Grade RGrade RGrade SGrade SRGrade RGrade RGrade RGrade RGrade S

Tolerance NTolerance RTolerance RTolerance RTolerance NTolerance RTolerance NTolerance RTolerance R





Blow-out direction:RightAxialRightAxialRightAxial

Degree of protection:IP55, fan IP54 IP55, fan IP54 IP55, fan IP54IP55, fan IP54IP55, fan IP54 IP55, fan IP54




Paint finish:PrimedPrimedAnthraciteAnthraciteAnthracite, two coats Anthracite, two coats

EMN

0123

013456

ABCDEFGHJ

ABCDJK

023568


© Siemens AG 2010



8/29Siemens NC 61 · 2010

8

1PH7 motor (SH 180 and SH 225)


2) Bearing version for coupling/belt output.3) Bearing version for increased cantilever force.4) Bearing version for increased maximum speed.5) Version for increased maximum speed only possible with vibration magnitude grade S. The following options are not possible:

• Shaft sealing ring6) Only appropriate if the sealing ring is occasionally lubricated with oil spray/mist. A sealing ring is not possible for type of construction IM B3 (IM V5, IM V6),

version with increased cantilever force or increased maximum speed.7) For preconditions for gearbox mounting, please refer to Gearboxes.8) Applies to type of construction IM B35, as type of construction IM B3, the motor is 20 kg (44 lb) lighter.9) Motors of shaft height 160 and higher require foot support.


Ratedtorque

Moment of inertia

Weight, approx.8)


SINAMICS S120 Motor ModuleRated output current for S1 duty

For additional versions and components, see SINAMICS S120 drive system


S1 S6-60 % S6-40 % S2-30 minNm (lbf-ft)

kgm2 (lbf-in-s2)

kg(lb)

A A A A A Order No.

1PH7184-..T...1PH7184-.. D...1PH7184-..E...1PH7184-.. F...1PH7184-.. L...

410 (302)372 (274)305 (225)325 (240)298 (220)

0.5 (4.43) 390 (860) 76 90 85120172

90106100149204

103126114174237

102126128174237

85132

85132200

6SL3127-1TE28-5AA36SL3127-1TE31-3AA36SL3127-1TE28-5AA36SL3127-1TE31-3AA36SL3127-1TE32-0AA3

1PH7186-.. T...1PH7186-.. D...1PH7186-.. E...1PH7186-.. F...1PH7186-.. L...

565 (417)487 (359)458 (338)471 (347)405 (299)

0.67 (5.93) 460 (1014) 105118120170235

126141135210290

147164150250345

130164156266355

132132132200260

6SL3127-1TE31-3AA36SL3127-1TE31-3AA36SL3127-1TE31-3AA36SL3127-1TE32-0AA36SL3327-1TE32-1AA3


13


01



© Siemens AG 2010

A s y n c h r o n o u s m o t o r s

Main spindle motors for SINAMICS S1201PH7 motors, standard typeSH 225 – Forced ventilation

8/30 Siemens NC 61 · 2010

8



Shaftheight

Rated speed






5) Prated


(HP)kW(HP)

kW(HP)

kW(HP)

Order No.


225 700100015002500

3100 2700 3600 4500 5500 55 (73.8)71 (95.2)

100 (134)142 (190)

66 (88.5)88 (118)

126 (169)176 (236)

75 (101)105 (141)136 (182)210 (282)

78 (105)114 (153)140 (188)220 (295)

1PH7224-7 7C7 7-07 7 71PH7224-7 7D7 7-07 7 71PH7224-7 7F7 7-07 7 71PH7224-7 7L7 7-07 7 7


27





FDQ



Type of construction: IM B3IM B3 (IM V5, IM V6) (hoisting system for vertical types of construction)IM B359) IM B35 (IM V15, IM V35) (hoisting system for vertical types of construction)9)

Bearing version for: Vibration magnitude: Shaft and flange accuracy:Coupling output Coupling outputCoupling output Coupling outputBelt outputBelt outputIncreased cantilever force(belt output)Increased cantilever force(belt output)Increased speed(coupling output)

Grade RGrade RGrade SGrade SRGrade RGrade RGrade R

Grade R

Grade S

Tolerance NTolerance RTolerance RTolerance RTolerance NTolerance RTolerance N

Tolerance R

Tolerance R











EMN

0123

0135

ABCDEFG

H

J

ABCDJK

023568


© Siemens AG 2010



8/31Siemens NC 61 · 2010







Ratedtorque

Moment of inertia

Weight, approx.8)




For additional versions and components, see SINAMICS S120 drive systemMrated J m Irated Irated

S1 S6-60 % S6-40 % S2-30 minNm (lbf-ft)

kgm2 (lbf-in-s2)

kg(lb)

A A A A A Order No.

1PH7224-..C...1PH7224-..D...1PH7224-.. F...1PH7224-.. L...

750 (553)678 (500)636 (469)542 (400)

1.48 (13.1) 650 (1433) 117164188298

135190230355

149222248419

155240256430

132200200310



13


01



© Siemens AG 2010


8/32 Siemens NC 61 · 2010

8



Shaftheight

Rated speed






5) Prated


(HP)kW(HP)

kW(HP)

kW(HP)

Order No.

Forced ventilation – LIne voltage 400 V 3 AC, operation on Active Line Module

225 100015002500

3100 2700 – 4500 – 92 (123)130 (174)168 (225)

114 (153)161 (216)208 (279)

136 (182)192 (257)248 (333)

136 (182)200 (268)265 (355)

1PH7226-7 7D7 7-07 7 71PH7226-7 7F7 7-07 7 71PH7226-7 7L7 7-07 7 7

100015002500

3100 2700 – 4500 – 113 (152)160 (215)205 (275)

140 (188)198 (266)254 (341)

167 (224)237 (318)303 (406)

167 (224)237 (318)310 (416)

1PH7228-7 7D7 7-07 7 71PH7228-7 7F7 7-07 7 71PH7228-7 7L7 7-07 7 7


27





FDQ



Type of construction: IM B3IM B3 (IM V5, IM V6) (hoisting system for vertical types of construction)IM B359) IM B35 (IM V15, IM V35) (hoisting system for vertical types construction)9)

Bearing version for: Vibration magnitude: Shaft and flange accuracy:Coupling output Coupling outputCoupling output Coupling outputBelt outputBelt outputIncreased cantilever force(belt output)Increased cantilever force(belt output)Increased speed(coupling output)

Grade RGrade RGrade SGrade SRGrade RGrade RGrade R

Grade R

Grade S

Tolerance NTolerance RTolerance RTolerance RTolerance NTolerance RTolerance N

Tolerance R

Tolerance R











EMN

0123

0135

ABCDEFG

H

J

ABCDJK

023568


© Siemens AG 2010



8/33Siemens NC 61 · 2010

8







Ratedtorque

Moment of inertia

Weight, approx.8)




For additional versions and components, see SINAMICS S120 drive systemMrated J m Irated Irated

S1 S6-60 % S6-40 % S2-30 minNm (lbf-ft)

kgm2 (lbf-in-s2)

kg(lb)

A A A A A Order No.

1PH7226-..D...1PH7226-.. F...1PH7226-.. L...

880 (649)828 (611)642 (474)

1.930 (17.1) 750 (1654) 198278362

237330428

280387501

389395511

200310380


1PH7228-..D...1PH7228-.. F...1PH7228-.. L...

1080 (797)1019 (752)783 (578)

2.326 (20.6) 860 (1896) 240350433

289413534

342483630

348491639

260380490



13


01



© Siemens AG 2010


1PH4 motors

8/34 Siemens NC 61 · 2010

8

■ Overview

Given the compact design of modern machines, the heat loss from electrical drives can have an adverse effect on the accu-racy of machining. The resulting demands for cold motors with a high power density led to the development of the water-cooled 1PH4 motors.

Furthermore, a combination of high torque and small construc-tion volume (low mass inertia) results in short acceleration and braking times, and thus in a reduction in non-productive time.

1PH4 motors are rugged, 4-pole asynchronous motors with squirrel-cage rotors. Power loss and noise emission are reduced to a minimum. Thanks to the compact design of the motors, high maximum speeds can be achieved.

The motors are equipped with an encoder system for sensing the motor speed and indirect position. In machine tools, the en-coder system is capable of C-axis operation as standard – that is, an additional encoder is not required for C-axis operation.

■ Benefits7 High power density thanks to the small construction volume7 Maximum speeds of up to 9000 rpm (optional: 12000 rpm)7 Full rated torque is continuously available, even at standstill7 Cooled flange to prevent thermal stressing of the connected

mechanical power train7 Low noise level7 High degree of protection IP65 (shaft exit IP55)7 High rotational accuracy7 High cantilever force loading7 Ruggedness

■ Application• Wherever extreme ambient conditions, such as high tempera-

tures, dust, dirt, or a corrosive atmosphere, do not permit air cooling

• In processes in which the environment must not be heated• On special machines, when cooling water is available

due to the process• Milling machines with full enclosure• High-load milling spindles• Counterspindles or rotating tools for turning machines


© Siemens AG 2010


1PH4 motors

8/35Siemens NC 61 · 2010

8



Refer to Liquid cooling for a list of heat exchanger manufacturers.



The graph shows the typical relationship between motor speed and drive power in 1PH4 motors for duty types in accordance with IEC 60034-1:

S1: Continuous duty


1) DE is the drive end with shaft. NDE is the non-drive end.2) For maximum permissible load, see the 1PH4 Motors Configuration Manual.3) Shaft extension run-out, concentricity of centering and shaft, and

perpendicularity of flange to shaft.4) For further configuration information, see the 1PH4 Motors Configuration

Manual.5) Values taken from the speed/power graph when using an Active Line Module

on a 400 V 3 AC supply system. It you are using a Smart Line Module, pro-ceed in accordance with the 1PH4 Motors Configuration Manual.

Product name 1PH4 motorCooling Water coolingCoolant inlet temperature Because of the formation of con-

densation, we recommend a coolant inlet temperature of approx. 30 °C (86 °F), depend-ing on the ambient conditions.

Cooling water pressure at inlet, max.

7 bar

Temperature monitoring 2 KTY 84 temperature sensors in the stator winding, 1 as reserve

Insulation of the stator winding in accordance withEN 60034-1 (IEC 60034-1)

Temperature class 155 (F) for a coolant inlet temperature of up to 30 °C (86 °F)

Encoder system, built-in• Without DRIVE-CLiQ interface • Incremental encoder sin/cos

1 Vpp 2048 S/R without C and D tracks (encoder IN2048S/R)

• Incremental encoder sin/cos 1 Vpp 2048 S/R with C and D tracks (encoder IC2048S/R)

• Absolute encoder 2048 S/R single-turn, 4096 revolutions multi-turn, with EnDat interface (encoder AM2048S/R)

• With DRIVE-CLiQ interface • 22 bit incremental encoder (resolution 4194304, 2048 S/R internal) + 11 bit commutation position (encoder IC22DQ)

• 22 bit incremental encoder (resolution 4194304, 2048 S/R internal) without commutation position (encoder IN22DQ)

• 22 bit absolute encoder single-turn (resolution 4194304, 2048 S/R internal) + 12 bit multi-turn (traversing range 4096 revolutions) (encoder AM22DQ)

Type of construction in accordance withEN 60034-7 (IEC 60034-7)

IM B35 (IM V15, IM V35)

Terminal box location (view DE)1)

Top, rotatable 4 × 90°

Terminal box connection type• Motor• Encoder system and

PTC thermistor

Terminals in terminal box 12-pin/17-pin circular socket(without mating connector) or DRIVE-CLiQ

Bearing version on DE2) Duplex bearing for belt or coupling output(minimum cantilever force required)

Vibration magnitude in accordance withEN 60034-14 (IEC 60034-14)

Grade R (reduced)


Tolerance N (normal)

Shaft extension DE in accordance with DIN 748-3 (IEC 60072-1)

Full-key balancing with keyway


IP65, IP55 on shaft exit

Sound pressure level LpA (1 m) in accordance with EN ISO 1680Tolerance + 3 dB• 1PH410/1PH413• 1PH416

69 dB71 dB

Paint finish AnthraciteApprovals, according to cURus



Type nrated n25)

S1 S6-60 % S6-40 %

rpm rpm rpm rpm

1PH41031PH41051PH4107

1500 860088008600

750076007400

650065006400

1PH41331PH41351PH41371PH4138

1500 8000740068007800

7400620058006600

6000550050005800

1PH41631PH41671PH4168

1500 630052006300

520044005300

450038004600

S6-40 %

S6-60 %

S1

00

n2S6-40 %

n2S6-60 %

n2S1

P

nmax

Motor power

Speed

Voltage limit

G_N

C01

_EN

_000

16b

nrated


© Siemens AG 2010


8/36 Siemens NC 61 · 2010

8


■ Options

When ordering a motor with options, -Z should be added to the order number. The order code should also be specified for each additional required option.

Order codes must not be repeated in plain text in the order.

Order No. 1PH4135-4NF26-Z

Order codes K05 + K09 + K31

Shaftheight

Ratedspeed

Continuous speed, max. Speed, max.1) Rated power for duty type

1PH4 asynchronous motor with solid shaftStandard type


3) nS1 cont.4) nmax

2) nmax3) nmax

4) Prated

S1 S6-60 % S6-40 %rpm rpm rpm rpm rpm rpm rpm kW

(HP)kW (HP)

kW (HP)

Order No.

Water cooling – Line voltage 400 V 3 AC, operation on Active Line Module

100 1500 5600 6500 10000 7500 9000 12000 7.5 (10.1)11 (14.8)14 (18.8)

8.75 (11.7)12.75 (17.1)16.25 (21.8)

10 (13.4)14.75 (19.8)18.75 (25.1)

1PH4103-47F261PH4105-47F261PH4107-47F26

132 1500 5200 6000 9250 6700 8000 10000 15 (20.1)22 (29.5)27 (36.2)30 (40.2)

18 (24.1)26.5 (35.5)32.5 (43.6)36 (48.3)

21 (28.2)31 (41.6)38 (51.0)42 (56.3)

1PH4133-47F261PH4135-47F261PH4137-47F261PH4138-47F26

160 1500 4000 4500 7000 5300 6500 8000 37 (49.6)46 (61.7)52 (69.7)

45 (60.3)55 (73.8)62.5 (83.8)

52.5 (70.4)65 (87.2)73 (97.9)

1PH4163-47F261PH4167-47F261PH4168-47F26



EMN



FDQ

Description Order code

Bearing version (view drive end)(standard = duplex bearing)• Single bearing for coupling, for low to medium

cantilever forces or planetary gearboxes (e.g. mounting of a ZF gearbox 2LG43...)5)6)

K00

Vibration magnitude in accordance with EN 60034-14 (IEC 60034-14) (standard = vibration magnitude grade R, duplex bearing)• Grade S with duplex bearing7)

• Grade S with single bearing7)

• Grade SR with single bearing7)

K05K02K03

Shaft and flange accuracy in accordance with DIN 42955 (IEC 60072-1)(standard = tolerance N)• Tolerance R8) K04

Shaft extension DE(standard = full-key balancing with keyway)• Plain shaft• Half-key balancing

K42L69

Description Order code

Shaft seal DE9)

• Radial shaft sealing ring, oil-tight, IP65 K18

Brake6)

• With holding brake mounted on DE G46

Terminal box location (view DE) (standard = top)• Right side, cable entry from below6)

• Left side, cable entry from below6)

Rotation of terminal box on its own axis• By 90°, cable entry from drive end10)

• By 90°, cable entry from non-drive end10)

• By 180°, cable entry from above10)

K0912)

K1013)

K83K84K8512)

Speed11)

• With increased maximum speed and half-key balancing

L37

Other• Second rating plate, separately packed K31


© Siemens AG 2010



8/37Siemens NC 61 · 2010

8

Notes on water cooling


2) Bearing version for duplex bearing.3) Bearing version for single bearing.4) Bearing version for increased speed using option L37.5) Vibration magnitude grades S, SR and mounting position IM V35 not possible for integrated gearbox.

Use order code K00 + G97 for old ZF gearbox 2LG42... (for gear selection, see Gearboxes).6) Options gear mounting, built-on brake, terminal box location on side are mutually exclusive.7) Automatically includes version K04. Options K05, K02 and K03 are mutually exclusive.8) Increased shaft accuracy.9) Only recommended if oil spray/mist occasionally gets onto the sealing ring.10)Options K83, K84 and K85 are mutually exclusive.11)Version for increased maximum speed includes vibration magnitude grade SR and half-key balancing. The following options are not possible:

• Shaft seal.12)K09 or K10 cannot be combined with K85.


Rated torque

Moment of inertia

Weight, approx.



Required rated output current for S1 duty

Booksize formatFor additional versions and components, see SINAMICS S120 drive systemMrated J m Irated Irated

S1 S6-60 % S6-40 %Nm (lbf-ft)

kgm2 (lbf -in-s2)

kg (lb)

A A A Order No.

1PH4103-...1PH4105-...1PH4107-...

48 (35.4)70 (51.6)90 (66.4)

0.017 (0.15)0.024 (0.21)0.031 (0.27)

52 (115)67 (148)80 (176)

263846

294252

324758

304560


1PH4133-...1PH4135-...1PH4137-...1PH4138-...

95 (70.1)140 (103)170 (125)190 (140)

0.046 (0.41)0.071 (0.63)0.085 (0.75)0.097 (0.86)

90 (198)112 (247)130 (287)150 (331)

557385

102

6586

100119

7499

114136

608585

132


1PH4163-...1PH4167-...1PH4168-...

235 (173)293 (216)331 (244)

0.17 (1.50)0.206 (1.82)0.22 (1.95)

175 (386)210 (463)240 (529)

107120148

125138173

142158197

132132200



01


MotorType

Coolant flow rate(water)

Connecting thread on non-drive end (NDE)

1PH410 6 l/min (1.59 US gallons) G 1/4"




© Siemens AG 2010


1PH2 built-in motors for direct drive

8/38 Siemens NC 61 · 2010

8

■ Overview

Active parts (rotor and stator) of 1PH2 asynchronous built-in motors

1PH2 built-in motors for turning machines are liquid-cooled squirrel-cage AC asynchronous motors. These built-in motors have been specially developed for variable-speed operation of main spindles on turning machines.

■ Benefits7 Compact design obtained by dispensing with mechanical

components such as coupling, belt drive, gearbox and spindle encoder

7 High power density as a result of liquid cooling7 The absence of drive transverse forces permits extremely high

accuracy on workpiece due to smooth, accurate spindle motion even at very low speeds

7 Extremely short ramp-up and braking times7 Full rated torque is continuously available, even at standstill7 Simple servicing by replacing complete motor spindles7 Increased rigidity of the spindle drive, achieved by mounting

the motor components between the main spindle bearings7 C-axis compatibility with hollow-shaft measuring system

mounted on the spindle7 Low noise level due to absence of machine elements7 Torque is transmitted to the spindle mechanically without play

by means of a cylindrical stepped press fit. The rotor is mounted on the spindle by thermal shrinking. The bond can be released by pressure-oil injection without affecting the joint surfaces.

7 The rotor with sleeve is pre-balanced and can be removedand subsequently remounted

7 The rotor with sleeve is finished-machined – that is, the rotor outer diameter does not need to be finished after mounting.

■ Application

1PH2 built-in motors are used for machines requiring excellent machining quality, accuracy and running smoothness.• Turning machines• Grinders


Refer to Liquid cooling for a list of heat exchanger manufacturers.

Product name 1PH2 built-in motor

Coolant inlet temperature Because of the formation of condensation, we recommend a coolant inlet temperature of approx. 25 °C (77 °F), depending on the ambient conditions.

Cooling water pressure at inlet, max.

7 bar

Cooling flow rate (water) 8l/min (2.11 US gallons)

Connecting thread Dependent on cooler used

Temperature monitoring 2 KTY 84 temperature sensors in the stator winding, 1 as reserve

Insulation of the stator winding in accordance withEN 60034-1 (IEC 60034-1)

Temperature class 155 (F) for a coolant inlet temperature of up to 25 °C (77 °F)

Motor encoder, recommended Hollow-shaft measuring system(not included in scope of supply)

Type of construction (cf. ISO) Individual components: Stator, rotor

Motor connection type Free cable ends with0.5 m (19.7 in) or 1.5 m (59.1 in) length

Balance quality of rotorin accordance with ISO 1940-1

1PH2093 to 1PH2118: G 2.5 Reference speed 3600 rpm

Degree of protectionin accordance with IEC 60034-5

IP00

Rating plate 1 unit supplied separately



© Siemens AG 2010


1PH2 built-in motors for direct drive

8/39Siemens NC 61 · 2010

8



The graph shows the typical relationship between motor speed and drive power for 1PH2 motors for the following duty types in accordance with IEC 60034-1:

S1: Continuous duty



2) Values taken from the speed/power graph when using an Active Line Mod-ule on a 400 V 3 AC supply system. If you are using a Smart Line Module, proceed in accordance with the 1PH2 Motors Configuration Manual.

S6-40 %

S6-60 %

S1

00

n2S6-40 %

n2S6-60 %

n2S1

P

nmax

Motor power

Speed

Voltage limit

G_N

C01

_EN

_000

16b

nrated



Type nrated n22)

rpmS1rpm

S6-60 %rpm

S6-40 %rpm

1PH20931PH2095

1500 4700 4000

4200 3600

3900 3300

1PH21131PH21151PH21171PH2118

1500 5400 4500 4700 5000

4800 4100 4200 4500

4400 3700 3800 4100


© Siemens AG 2010

Asynchronous motorsMain spindle motors for SINAMICS S1201PH2 built-in motors for direct driveWater cooling

8/40 Siemens NC 61 · 2010

8


1) Data for ΔT = 70 K, unless specified otherwise.

Rated speed

Speed, max.

Rated power for duty type1)

1PH2 asynchronousbuilt-in motor for direct driveStandard type

Rated torque1)

nrated nmax Prated Mrated

S1 S1ΔT=105 K

S6-60 % S6-40 % ΔT=105 K

rpm rpm kW (HP)

kW (HP)

kW (HP)

kW (HP)

Order No. Nm (lbf-ft)

Nm (lbf-ft)

Water cooling – Line voltage 400 V 3 AC, operation on Active Line Module

1500 10000 7.5 (10.1)10.1 (13.5)

9.4 (12.6)13 (17.4)

8.2 (11.0)11 (14.8)

9 (12.1)12 (16.1)

1PH2093-6WF471PH2095-6WF47

48 (35.4)64 (47.2)

60 (44.3)83 (61.2)

1500 10000 15.1 (20.2)16.5 (22.1)18.1 (24.3)23.6 (31.6)

18.5 (24.8)21.5 (28.8)23.7 (31.8)30.9 (41.4)

17 (22.8)18.5 (24.8)20.5 (27.5)26 (34.9)

19 (25.5)21 (28.2)23 (30.8)29.5 (39.6)

1PH2113-6WF471PH2115-6WF471PH2117-6WF471PH2118-6WF47

95 (70.1)105 (77.4)115 (84.8)146 (108)

118 (87.0)137 (101)151 (111)197 (145)

Free cable ends: Length: 1.5 m (59.1 in)Length: 0.5 m (19.7 in) (preferred type)

12


© Siemens AG 2010


1PH2 built-in motors for direct driveWater cooling

8/41Siemens NC 61 · 2010

8

■ Dimensional drawing


Moment of inertia of rotor

Weight(rotorand stator),approx.

Rated current for duty type1)


Required rated output current for S1 duty


J m Irated Irated

S1 S6-60 % S6-40 %

kgm2 (lbf-in-s2)

kg (lb)

A A A A Order No.

1PH2093-6W...1PH2095-6W...

0.028 (0.25)0.036 (0.32)

33 (72.8) 42 (92.6)

24 30

26 32

28 34

3030

6SL3127-1TE23-0AA36SL3127-1TE23-0AA3

1PH2113-6W...1PH2115-6W...1PH2117-6W...1PH2118-6W...

0.066 (0.58)0.073 (0.65)0.079 (0.70)0.100 (0.89)

51 (112) 56 (123) 62 (137) 78 (172)

56 55 60 82

61 60 67 90

67 66 74

100

60606085



01


G_N

C01

_EN

_001

48a

Hollow shaft Annular jacket cooling channel

Rotor Rotor sleeve

Air gap stator

1PH2 motor

Standard spindle diameter

Rotor internal diameter

Stator outer diameter

Total outer diameter

Total length

Type d di DA D L

mm (in) mm (in) mm (in) mm (in) mm (in)

1PH20931PH2095

67 (2.64) 85 (3.35) 180 (7.09) 205 (8.07) 250 (9.84)300 (11.81)

1PH21131PH21151PH21171PH2118

82 (3.23) 100 (3.94) 220 (8.66) 250 (9.84) 290 (11.42)310 (12.20)330 (12.99)390 (15.35)


© Siemens AG 2010

Asynchronous motorsLiquid cooling

For 1PH4/1PH2/1FE1 motors

8/42 Siemens NC 61 · 2010

8

■ Overview

Cooling principleFor design of the cooling units, see Configuration Manual.

Cooling unit manufacturersNon-Siemens products whose fundamental suitability is familiar to us. It goes without saying that equivalent products from other manufacturers may be used. Our recommendations are to be seen as helpful information, not as requirements or dictates. We do not warrant the composition, nature, state or quality of non-Siemens products.

Please contact the companies below for technical information.

Return Inlet q = 8 l/min to 10 l/min

Toff Ton

Heat exchanger

Annular jacket cooling channel

Motor

G_N

C01

_EN

_000

23b

BKW Kälte-Wärme-Versorgungstechnik GmbH

Contact:Mr. Walker

Benzstraße 272649 WOLFSCHLUGEN, GermanyPhone: +49 7022 5003-0Fax: +49 7022 5003-30E-mail: [email protected]

DELTATHERM Hirmer GmbH

Contact:Mr. Hirmer

Gewerbegebiet Bövingen12253804 MUCH, GermanyPhone: +49 2245 6107-0Fax: +49 2245 6107-10E-mail: [email protected]

Glen Dimplex Deutschland GmbHGeschäftsbereich RIEDEL Kältetechnik

Contact:Mr. Schneider

Am Goldenen Feld 1895326 KULMBACH, GermanyPhone: +49 9221 709-555Fax: +49 9221 709-549E-mail: [email protected]

Helmut Schimpke Industriekühlanlagen GmbH + Co. KG

Contact:Mr. Geerkens

Ginsterweg 25-2742781 HAAN, GermanyPhone: +49 2129 9438-0Fax: +49 2129 9438-99E-mail: [email protected]

Hydac System GmbH

Contact:Mr. Klein

Postfach 125166273 SULZBACH/SAAR, GermanyPhone: +49 6897 509-708Fax: +49 6897 509-454E-mail: [email protected]

Hyfra Industriekühlanlagen GmbH

Contact:Mr. Forberger

Industriepark 5456593 KRUNKEL, GermanyPhone: +49 2687 898-0Fax: +49 2687 898-25E-mail: [email protected]

KKT Kraus Kälte- und Klimatechnik GmbH

Contact:Mr. Titschack

Industriestraße 23a91207 LAUF A. D. PEGNITZ, GermanyPhone: +49 9123 174-909Fax: +49 9123 174-910E-mail: [email protected]

Pfannenberg GmbH

Contact:Mr. Hille

Werner-Witt-Straße 121035 HAMBURG, GermanyPhone: +49 40 73412-127Fax: +49 40 73412-101E-mail: [email protected]


© Siemens AG 2010

Asynchronous motorsGearboxes

Two-speed gearboxesfor 1PH7/1PH4 motors

8/43Siemens NC 61 · 2010

8

■ Application

Change-speed gearboxes increase the drive torque at low motor speeds and expand the range of constant power output avail-able from the main spindle motor. The full cutting capacity of modern machine tools can therefore be utilized throughout the entire speed range.

■ Benefits

The performance characteristics of the two-speed gearboxes for 1PH7/1PH4 motors are as follows:7 Drive power up to 100 kW (134 HP)7 Constant power range at drive shaft up to 1:247 Suitable for both directions of rotation7 Motor shaft heights SH 100 to SH 2257 Types of construction IM B35 and IM V15 (IM V35 available on

request)

Mounting the change-speed gearbox outside the headstock of the machine tool has the following advantages:7 Easy adaptation to the machine tool7 Low noise and no temperature fluctuations due to gearing

inside the headstock7 Separate lubrication systems for the main spindle (grease)

and the change-speed gearbox (oil)7 Gearbox efficiency > 95 %7 Instead of V belts, the drive power can also be transmitted

from the gear output by a gear wheel (available on request) or coaxially by means of a flexible coupling.

■ Design

The two-speed gearboxes have a planetary design. The central sun wheel distributes the power to several planet wheels which revolve around it. The outstanding advantage of this design is its compactness. The gear-changing device, a splined sleeve that moves axially, is of form-fit design.

Position 1: Gear ratio i1 = 4Position 2: Gear ratio i2 = 1

The motor is flange-mounted onto the change-speed gearbox using an adapter plate. The AC motor must be suitably prepared for mounting.

For shaft heights of SH 160 and higher, motors of types of construction IM B35 and IM V15 must be supported free from stress on the non-drive end.

Any transverse force imported into the gearbox has to be borne by the gearbox and transmitted to the machine base.

The motors for all 2K gearboxes must be full-key balanced with a fitted key. The 2K 120, 2K 250, 2K 300 gearboxes are enclosed, so that the motor flange is adequately sealed in the standard ver-sion.Vertical mounting positions for the IM V15 and IM V35 require circulating-oil lubrication of the gearboxes.

The standard version of the change-speed gearboxes up to and including the 2K 300 has a maximum circumferential backlash of 30 angular minutes (measured at the gear output). Several spe-cial versions suitable for milling or machining with cut interrup-tion can be supplied on request:• Reduced backlash with special features: max. 20'• Reduced backlash for high performance: max.15'

1) Not included in scope of supply.

■ Design (continued)

Profile of a planetary gearbox

The power unit (motor and gearbox) is supplied with vibration magnitude grade R in accordance with EN 60034-14 (IEC 60034-14). This is also the case when the motor is ordered with vibration magnitude grade S.

The belt pulley1) should be a cup wheel type pulley. For mounting the pulley, the output shaft on the gearbox has a flange with an external centering spigot and tapped holes for easy fitting and removal of the pulley.


The use of a change-speed gearbox permits the constant power range to be greatly increased.

Power-speed graph

Legend:nrated Rated speednrated' Rated speed with two-stage gearboxnmax Max. permissible speedPrated Rated power and constant power of the motor

in the speed range between nrated and nmax or nrated' and nmaxM Torque

n

P

P = constant

P = constant

with gearbox

without gearbox

nrated' nratedM = constant

M = constant Logarithmic scale

G_N

C01

_EN

_000

17a

nmax

Prated

1

1

1

1

2

22

2


© Siemens AG 2010

Asynchronous motorsGearboxesTwo-speed gearboxesfor 1PH7/1PH4 motors

8/44 Siemens NC 61 · 2010

8


For further binding technical specifications and configuring aid (e.g. lubrication, temperature rise and typical applications), please refer to the latest catalog supplied by ZF (Zahnradfabrik Friedrichshafen). The permissible characteristics of the motor and gearbox are a governing factor in the design of the com-plete drive unit (motor and gearbox).

With 1PH4168 or 1PH7167-2NB motors, for example, the rated torque must be reduced to 300 Nm (221 lbf -ft). With motors of SH 132, please note that the maximum permissible speed of the 2K 250 gearbox for splash lubrication is 6300 rpm.


1) Higher drive speeds are allowed with oil-cooled gearboxes and for gear ratios i =1 in some instances (refer to the ZF Catalog).

2) Special versions, such as gearboxes with different torsional backlash, or other gear ratios (i = 3.17 or i = 5.5), are available on request.

3) Preconditions: DE shaft extension with fitted key and full-key balancing. Option K18 required for 1PH4.

4) Preconditions: DE shaft extension with fitted key and full-key balancing. Bearing version for coupling output. Shaft and flange accuracy tolerance R. DE flange with shaft sealing ring.

Motors with built-on planetary gearboxThe 1PH motors can also be supplied with flange-mounted pla-netary gearboxes. The motor-gearbox unit is tested for correct functioning. The complete drive unit - that is, 1PH7 or 1PH4 motor with mounted ZF change-speed gearbox – can be ordered directly from Siemens:

The following details must be specified with the order:

Ordering example for 1PH4 motor:

Motor complete with gearbox1PH4133-4NF26-ZK002LG4315-3FD11

Ordering example for 1PH7 motor:

Motor complete with gearbox1PH7186-2NE03-0BC22LG4260-1JC211PH7163-2NF03-0CC02LG4320-3JD11

1PH motor

Gearbox

ZF identifier

Type Speed, max.1)

Rated torque, permissible(S1 duty)

Maximum torque, permissible(S6-60 % duty)

Moment of inertia ofgearbox

Weight of gearbox, approx.

Shaft height

Drive Drive Outputi = 1

Outputi = 4

Drive Outputi = 1

Outputi = 4

Outputi = 1

Outputi = 4

SH nmax M M M M M M J J m

rpm Nm (lbf-ft)

Nm (lbf -ft)

Nm (lbf-ft)

Nm (lbf -ft)

Nm (lbf -ft)

Nm (lbf-ft)

kgm2 (lbf-in-s2)

kgm2 (lbf-in-s2)

kg (lb)

100 2K 120 2LG4312-... 8000 120 (88.5)

120 (88.5)

480 (354)

140 (103)

140 (103)

560 (413)

0.0110 (0.10)

0.0114 (0.10)

30 (66.2)

132 2K 250 2LG4315-... 6300 250(184)

250 (184)

1000 (738)

400 (295)

400 (295)

1600 (1180)

0.0270 (0.24)

0.0570 (0.50)

62 (137)

160 2K 300 2LG4320-... 6300 300 (221)

300 (221)

1200 (885)

400 (295)

400 (295)

1600 (1180)

0.0270 (0.24)

0.0570 (0.50)

70 (154)

180 2K 8002K 801

2LG4250-...2LG4260-...

5000 800 (590)

800 (590)

3200 (2360)

900 (664)

900 (664)

3600 (2655)

0.1956 (1.73)

0.1766 (1.56)

110 (243)

225 2K 802 2LG4270-... On request

Type of construction for complete unit

Output flange dimension D2

Two-speed gearbox (standard version)2)

Gear stage i1 = 4

mm (in) Order No. ZFidentifier

For 1PH710/1PH410 motors3)

IM B5,IM B35,IM V1,IM V15

100 (3.94) 2LG4312-3CC31 2K 120


IM B5,IM B35

118 (4.65) 2LG4315-3FD11 2K 250

IM V1,IM V15

118 (4.65) 2LG4315-3FC11 2K 250


IM B35 130 (5.12) 2LG4320-3JD11 2K 300

IM V15 130 (5.12) 2LG4320-3JC11 2K 300

For 1PH7184 motors4)

IM B35,IM V15

180 (7.09) 2LG4250-1JC11 2K 800

For 1PH7186 motors4)

IM B35,IM V15

180 (7.09) 2LG4260-1JC21 2K 801

Siemens AG

Industrial Solutions and ServicesContact: Mr. Britz

Im Schiffelland 1066386 ST. INGBERT, Germany

Fax: +49 6894 891-112E-mail: [email protected]


© Siemens AG 2010

Asynchronous motorsSelection guides

Degree of protection

8/45Siemens NC 61 · 2010

8

■ More information ■ More information

The degree of protection designation in accordance with EN 60034-5 (IEC 60034-5) is made using the letters "IP" and two digits (e.g., IP64). The second digit in the degree of protection designation represents the protection against water, the first digit the protection against penetration of foreign matter.

Since coolants used for machine tools and transfer machines usually contain oil, are able to creep, and may also be corrosive, protection against water alone is insufficient. The indicated de-gree of protection should only be considered here as a guide-line. The motors must be protected by suitable covers. Attention must be paid to providing suitable sealing of the motor shaft for the selected degree of protection for the motor.

The table can serve as a decision aid for selecting the proper degree of protection for motors. For a mounting position with vertical shaft end IM V3/IM V19, static fluid on the flange is only permitted with degree of protection IP67/IP68 and recessed DE flange in some cases.

1) IP64 with dry run at shaft exit.

Type of construc-tion/mounting position

Desig-nation


Desig-nation


Desig-nation

IM B3 IM B5IM B14

IM B35

IM V5 IM V1IM V18

IM V15

IM V6 IM V3IM V19

IM V35

Liquids

Effect

General workshop environment

Water;gen. cooling lubricant (95 % water,5 % oil);oil

Creep oil;petroleum;aggressivecooling lubricants

Dry IP64 – –

Water-enriched environment

– IP64 IP671)

Mist – IP65 IP67

Spray – IP65 IP68

Jet – IP67 IP68

Surge, brief immersion; constant inundation

– IP67 IP68

Type of construction/mounting position

NC61_en_Kap08_43.fm Seite 45 Freitag, 15. Januar 2010 7:53 07

© Siemens AG 2010

Asynchronous motorsDimensional drawings1PH8 motorsSH 80 – Forced ventilation

8/46 Siemens NC 61 · 2010

8

■ Dimensional drawings

For motor Dimensions in mm (in)

Shaft height

Type DINIEC

aB

bA

cHA

fAB

hH

kLB

mBA

m1–

m2–

nAA

pHD

p1–

sK

s3–

w1C

1PH8, type of construction IM B3, forced ventilation

80 1PH8083 194(7.64)

125(4.92)

8(0.31)

155(6.1)

80(3.15)

375(14.76)

42(1.65)

62(2.44)

20(0.79)

35(1.38)

216(8.5)

253.5(9.98)

10(0.39)

M25×1.5 38(1.5)

1PH8087 244(9.61)

425(16.73)

DE shaft extension Version with hollow shaft

Shaft height

Type DINIEC

dD

d6–

tGA

uF

kLB

k1–

lL

80 1PH8083 32(1.26)

M12 35(1.38)

10(0.39)

575(22.64)

319.3(12.57)

80(3.15)

1PH8087 625(24.61)

369.3(14.54)

G_P

M21

_XX

_000

01b

mw1

øs

a

ød

t

u

c

m2

s3

m1n

b

k

phd6

f

l

G_P

M21

_XX

_000

43

mw1

øs

ak1

ød

m2

s3

m1 a1

k

h

NDE shaft extension

6 x M5 / 7 depth 7, over Ø102

DE shaft extension

G_PM21_EN_00053

Ø8

(Ø0.

31)

13(0.51)

1.5(0.06)

2(0.08)

10.5

SW 19

(0.41)

4(0.16)

25.5(1.00)

32(1.26)

31(1.22)

340.05 C (1.34)

L

0.002 C

C D

M12

x1.2

5-R

H

RZ16

RZ2

560

°

Ø16

H7

(Ø0.

63H

7 )

Ø0.04 CØ0.002 C

RZ6.3

60°

Ø14

(Ø0.

55

)

Ø14

.5(Ø

0.57

)

Ø0.007 DØ0.0003 D

+0.0

08-0

.001 +0

.000

3-0

.000

04

M12

x1.2

5-LH

Ø11

4(Ø

4.49

)

0.005 D0.0002 D

18.5(0.73)

RZ6.3

1.5(0.06)

(Ø4.02)

1PH808

Version withhollow shaft


© Siemens AG 2010

Asynchronous motorsDimensional drawings

1PH8 motorsSH 80 – Forced ventilation

8/47Siemens NC 61 · 2010

8



Shaft height

Type DINIEC

a1P

b1N

c1LA

e1M

fAB

f1T

hH

kLB

pHD

p1–

s2–

s3–


80 1PH8083 200(7.87)

130(5.12)

12(0.47)

165(6.5)

155(6.1)

3.5(0.14)

77.5(3.05)

375(14.76)

213.5(8.41)

251(9.88)

12(0.47)

M25×1.5

1PH8087 425(16.73)


Shaft height

Type DINIEC

dD

d6–

i2E

tGA

uF

kLB

k1–

lL

80 1PH8083 32(1.26)

M12 80(3.15)

35(1.38)

10(0.39)

575(22.64)

319.3(12.57)

80(3.15)

1PH8087 625(24.61)

369.3(14.54)

G_PM21_EN_00042a

Connector size 1 for connection of fan

p 1G

_PM

21_X

X_0

0002

at

u

c1

ød

f1i2 øs2

a1

e 1

k

ph

øb1

d6

s3

f

l

Version with powerconnector size 1.5

1PH808


© Siemens AG 2010

Asynchronous motorsDimensional drawings1PH8 motorsSH 100/SH 132 – Forced ventilation

8/48 Siemens NC 61 · 2010

8



Shaft height

Type DINIEC

aB

bA

cHA

c1LA

fAB

f1T

hH

kLB

mBA

m1–

m2–

nAA

pHD

p1–

p2–

p3–


100 1PH8101 167(6.57)

160(6.3)

11(0.43)

– 196(7.72)

– 100(3.94)

369.5(14.55)

44(1.73)

74(2.91)

19(0.75)

40(1.57)

252(9.92)

294(11.6)

198(7.80)

276.5(10.89)

1PH8103 202.5(7.97)

405(15.94)

1PH8105 262(10.31)

464.5(18.29)

1PH8107 297.5(11.71)

500(19.69)

132 1PH8131 220.5(8.68)

216(8.5)

15(0.59)

18(0.71)

260(10.24)

– 132(5.2)

439(17.28)

57(2.24)

93(3.66)

27(1.06)

52(2.05)

317.5(12.5)

347(13.66)

262(10.31)

357.5(14.07)

1PH8133 265.5(10.5)

484(19.06)

1PH8135 310.5(12.2)

529(20.83)

1PH8137 350.5(13.8)

569(22.40)


Shaft height

Type DINIEC

sK

s3–

s4–

w1C

dD

d6–

tGA

uF

kLB

k1–

pHD

p3–

s3–

lL

100 1PH8101 12(0.47)

M32×1.5 M20×1.5 43(1.69)

38(1.5)

M12 41(1.61)

10(0.39)

569.5(22.42)

312.3(12.3)

266.5(10.49)

276.5(10.89)

M32×1.5 80(3.15)

1PH8103 605(23.82)

347.8(13.69)

1PH8105 664.5(26.16)

407.3(16.04)

1PH8107 700(27.56)

442.8(17.43)

132 1PH8131 12(0.47)

M40×1.5 M20×1.5 53(2.09)

48(1.89)

M16 51.5(2.03)

14(0.55)

639(25.16)

372.8(14.68)

347.5(13.68)

357.5(14.07)

M50×1.5 110(4.33)

1PH8133 684(26.93)

417.8(16.45)

1PH8135 729(28.7)

462.8(18.22)

1PH8137 769(30.28)

502.8(19.8)

G_P

M21

_XX

_000

67

møs

a

ød

t

u

c

m2m1

nb

k

p 2

p3

p

hd6

w1

s3

s4

f

Connector size 1 for fan connection

G_PM21_EN_00044

p 1

1PH810 Version with power connector size 1.5


© Siemens AG 2010


1PH8 motorsSH 100/SH 132 – Forced ventilation

8/49Siemens NC 61 · 2010

8


G_P

M21

_XX

_000

05b

møs

a

ød

t

u

c

m2m1

nb

k

p 2

p3

p

hd6

w1

s3

s4

f

l


G_PM21_EN_00045

p 1

G_P

M21

_XX

_000

46

møs

ak1

ød

m2m1

k

w1

s3

s4

h

a1

NDE shaft extension

6 x M5 / depth 7, over Ø102

DE shaft extension

G_PM21_EN_00054

Ø11

.5(Ø

0.45

)

17(0.67)

1.5(0.06)

2(0.08)

10.5

SW 27

(0.41)

4(0.16)

25.5(1.00)

37(1.46)

38(1.50)

450.05 C (1.78)

L

0.002 C

C D

M16

x1.5

-RH

RZ16

RZ2

560

°

Ø20

H7

(Ø0.

79H

7 )

Ø0.04 CØ0.002 C

RZ6.3

60°

Ø18

(Ø0.

71

)

Ø18

.5(Ø

0.73

)

Ø0.007 DØ0.0003 D

+0.0

07-0

.003 +0

.000

3-0

.000

1

M16

x1.5

-LH

Ø11

4(Ø

4.49

)

0.005 D0.0002 D

18.5(0.73)

RZ6.3

1.5(0.06)

(Ø4.02)

1PH813 Version with power connector size 3

Version with hollow shaft


© Siemens AG 2010


8/50 Siemens NC 61 · 2010

8



Shaft height

Type DINIEC

aB

a1P

bA

b1N

cHA

c1LA

e1M

fAB

f1T

hH

kLB

mBA

m1–

m2–

nAA

pHD

p1–


100 1PH8101 167(6.57)

250(9.84)

160(6.3)

180(7.09)

11(0.43)

16(0.63)

215(8.46)

196(7.72)

4(0.16)

100(3.94)

369.5(14.55)

44(1.73)

74(2.91)

19(0.75)

40(1.57)

252(9.92)

294(11.57)

1PH8103 202.5(7.97)

405(15.94)

1PH8105 262(10.31)

464.5(18.29)

1PH8107 297.5(11.71)

500(19.69)


Shaft height

Type DINIEC

p2–

p3–

sK

s2–

s3–

s4–

w1C

dD

d6–

i2E

tGA

uF

kLB

k1–

pHD

p3–

s3–

lL

100 1PH8101 198(7.8)

276.5(10.89)

12(0.47)

14(0.55)

M32×1.5 M20×1.5 43(1.69)

38(1.5)

M12 80(3.15)

41(1.61)

10(0.39)

569.5(22.42)

312.3(12.3)

266.5(10.49)

276.5(10.89)

M32×1.5 80(3.15)

1PH8103 605(23.82)

347.8(13.69)

1PH8105 664.5(26.16)

407.3(16.04)

1PH8107 700(27.56)

442.8(17.43)

G_P

M21

_XX

_000

69

møs

a

ødøb1

t

u

c

m2

f1

m1n

b

kc1i2

p 2

p3p

hd6

w1

s3

s4

f

a1

øs2

e 1


G_PM21_EN_00045

p 1

Version with power connector size 3

1PH810


© Siemens AG 2010



8/51Siemens NC 61 · 2010

8



Shaft height

Type DINIEC

a1P

b1N

c1LA

e1M

fAB

f1T

hH

kLB

pHD

p1–

p2–

p3–


100 1PH8101 250(9.84)

180(7.09)

16(0.63)

215(8.46)

196(7.72)

4(0.16)

98(3.86)

369.5(14.55)

250(9.84)

292(11.5)

– –

1PH8103 405(15.94)

1PH8105 464.5(18.29)

1PH8107 500(19.69)


Shaft height

Type DINIEC

s2–

s3–

s4–

dD

d6–

i2E

tGA

uF

kLB

k1–

pHD

s3–

lL

100 1PH8101 14(0.55)

M32×1.5 M20×1.5 38(1.5)

M12 80(3.15)

41(1.61)

10(0.39)

569.5(22.42)

312.3(12.3)

264.5(10.41)

M32×1.5 80(3.15)

1PH8103 605(23.82)

347.8(13.69)

1PH8105 664.5(16.16)

407.3(16.04)

1PH8107 700(17.56)

442.8(17.43)

G_P

M21

_XX

_000

77

ødøb1

t

u

f1

kc1i2

phd6

s3

s4

f

a1

øs2

e 1


G_PM21_EN_00044

p 1

1PH810

Version with power connector size 1.5


© Siemens AG 2010


8/52 Siemens NC 61 · 2010

8



Shaft height

Type DINIEC

aB

a1P

bA

b1N

cHA

c1LA

e1M

fAB

f1T

hH

kLB

mBA

m1–

m2–

nAA

pHD

p1–


132 1PH8131 220.5(8.68)

340(13.4)

216(8.5)

250(9.84)

15(0.59)

18(0.71)

300(11.81)

260(10.24)

5(0.2)

132(5.2)

439(17.28)

65(2.56)

93(3.66)

35(1.38)

52(2.05)

317.5(12.5)

347(13.66)

1PH8133 265.5(10.5)

484(19.06)

1PH8135 310.5(12.2)

529(20.83)

1PH8137 350.4(13.8)

569(22.40)


Shaft height

Type DINIEC

p2–

p3–

sK

s2–

s3–

s4–

w1C

dD

d6–

i2E

tGA

uF

kLB

k1–

pHD

p3–

s3–

lL

132 1PH8131 262(10.31)

357.5(14.07)

12(0.47)

18(0.71)

M40×1.5 M20×1.5 53(2.09)

48(1.89)

M16 110(4.33)

51.5(2.03)

14(0.55)

639(25.16)

372.8(14.68)

347.5(13.68)

357.5(14.07)

M50×1.5 110(4.33)

1PH8133 684(26.93)

417.8(16.45)

1PH8135 729(28.7)

462.8(18.22)

1PH8137 769(30.28)

502.8(19.8)

G_P

M21

_XX

_000

07a

t

u

ød

i2

a1

kp 2

p

h

møs

a

c

m2m1

nb

d6

w1

s3

s4

c1

f1

øs2

e 1

øb1

f

p31PH813


G_PM21_EN_00045

p 1



© Siemens AG 2010



8/53Siemens NC 61 · 2010

8



Shaft height

Type DINIEC

a1P

b1N

c1LA

e1M

fAB

f1T

hH

kLB

pHD

p1–

p2–

p3–


132 1PH8131 340(13.39)

250(9.84)

18(0.71)

300(11.81)

260(10.24)

5(0.2)

130(5.12)

439(17.28)

315.5(12.42)

345(13.58)

– –

1PH8133 484(19.06)

1PH8135 529(20.83)

1PH8137 569(22.40)


Shaft height

Type DINIEC

s2–

s3–

s4–

dD

d6–

i2E

tGA

uF

kLB

k1–

pHD

s3–

lL

132 1PH8131 18(0.71)

M40×1.5 M20×1.5 48(1.89)

M16 110(4.33)

51.5(2.03)

14(0.55)

639(25.16)

372.8(14.68)

346(13.62)

M50×1.5 110(4.33)

1PH8133 684(26.93)

417.8(16.45)

1PH8135 729(28.7)

462.8(18.22)

1PH8137 769(30.28)

502.8(19.8)

G_P

M21

_XX

_000

76

t

u

ød

i2

a1

kp

hc1

f1

øb1

d6

s3

s4 øs2

e 1

f


G_PM21_EN_00045

p 1

1PH813



© Siemens AG 2010

Asynchronous motorsDimensional drawings1PH8 motorsSH 80 to SH 132 – Water cooling

8/54 Siemens NC 61 · 2010

8



Standard/Advanced/Performance

High Performance

without hollow shaft

withhollow shaft

Shaft height

Type DINIEC

aB

bA

cHA

fAB

hH

kLB

kLB

kLB

mBA

m1–

m2–

nAA

1PH8, type of construction IM B3, water cooling

80 1PH8083 194(7.64)

125(4.92)

8(0.31)

155(6.1)

80(3.15)

301.5(11.87)

306.3(12.06)

319.3(12.57)

37(1.46)

63.5(2.5)

15(0.59)

35(1.38)

1PH8087 244(9.61)

351.5(13.84)

356.3(14.03)

369.3(14.54)

100 1PH8101 167(6.57)

160(6.3)

11(0.43)

196(7.72)

100(3.94)

289.5(11.4)

294.5(11.59)

312.3(12.3)

44(1.73)

68(2.68)

19(0.75)

43(1.69)

1PH8103 202.5(7.97)

325(12.8)

330(12.99)

347.8(13.69)

1PH8105 262(10.31)

384.5(15.14)

389.5(15.33)

407.3(16.04)

1PH8107 297.5(11.71)

420(16.54)

425(16.73)

442.8(17.43)

132 1PH8131 220.5(8.68)

216(8.5)

15(0.59)

260(10.24)

132(5.2)

347.5(13.68)

354.8(13.97)

372.8(14.68)

42(1.65)

81(3.19)

12(0.47)

43(1.69)

1PH8133 265.5(10.5)

392.5(15.45)

399.8(15.74)

417.8(16.45)

1PH8135 310.5(12.2)

437.5(17.22)

444.8(17.54)

462.8(18.22)

1PH8137/8 350.5(13.8)

477.5(18.8)

484.8(19.09)

502.8(19.8)

DE shaft extension

Shaft height

Type DINIEC

pHD

p1–

p2–

p3–

sK

s3–

w1C

dD

d6–

tGA

uF

lL

80 1PH8083 216(8.5)

253.5(9.98)

– – 10(0.39)

M25×1.5 38(1.5)

32(1.26)

M12 35(1.38)

10(0.39)

80(3.15)

1PH8087

100 1PH8101 266.5(10.49)

294(11.57)

198(7.8)

276.5(10.89)

12(0.47)

M32×1.5 43(1.69)

38(1.5)

M12 41(1.61)

10(0.39)

80(3.15)

1PH8103

1PH8105

1PH8107

132 1PH8131 347.5(13.68)

347(13.66)

262(10.31)

357.5(14.07)

12(0.47)

M50×1.5 53(2.09)

48(1.89)

M16 51.5(2.03)

14(0.55)

110(4.33)

1PH8133

1PH8135

1PH8137/8


© Siemens AG 2010


1PH8 motorsSH 80 to SH 132 – Water cooling

8/55Siemens NC 61 · 2010

8


G_P

M21

_XX

_000

03a

mw1

øs

a

ød

t

u

c

m2m1

nb

k

phd6

s3

f

l

G_PM21_XX_00047

p 1

NDE shaft extension


DE shaft extension

G_PM21_EN_00053

Ø8

(Ø0.

31)

13(0.51)

1.5(0.06)

2(0.08)

10.5

SW 19

(0.41)

4(0.16)

25.5(1.00)

32(1.26)

31(1.22)

340.05 C (1.34)

L

0.002 C

C D

M12

x1.2

5-R

H

RZ16

RZ2

560

°

Ø16

H7

(Ø0.

63H

7 )

Ø0.04 CØ0.002 C

RZ6.3

60°

Ø14

(Ø0.

55

)

Ø14

.5(Ø

0.57

)

Ø0.007 DØ0.0003 D

+0.0

08-0

.001 +0

.000

3-0

.000

04

M12

x1.2

5-LH

Ø11

4(Ø

4.49

)

0.005 D0.0002 D

18.5(0.73)

RZ6.3

1.5(0.06)

(Ø4.02)

G_P

M21

_XX

_000

70a

møs

a

ød

t

u

c

m2m1

nb

k

p 2p

hd6

w1

s3

f

p3

l

G_PM21_XX_00047

p 1

G_P

M21

_XX

_000

08a

møs

a

ød

t

u

c

m2m1

nb

k

p 2p

hd6

w1

s3

f

p3

l

G_PM21_XX_00048

p 1

NDE shaft extension


DE shaft extension

G_PM21_EN_00054

Ø11

.5(Ø

0.45

)

17(0.67)

1.5(0.06)

2(0.08)

10.5

SW 27

(0.41)

4(0.16)

25.5(1.00)

37(1.46)

38(1.50)

450.05 C (1.78)

L

0.002 C

C D

M16

x1.5

-RH

RZ16

RZ2

560

°

Ø20

H7

(Ø0.

79H

7 )

Ø0.04 CØ0.002 C

RZ6.3

60°

Ø18

(Ø0.

71

)

Ø18

.5(Ø

0.73

)

Ø0.007 DØ0.0003 D

+0.0

07-0

.003 +0

.000

3-0

.000

1

M16

x1.5

-LH

Ø11

4(Ø

4.49

)

0.005 D0.0002 D

18.5(0.73)

RZ6.3

1.5(0.06)

(Ø4.02)





1PH810

1PH813



© Siemens AG 2010


8/56 Siemens NC 61 · 2010

8



DE shaft extension

Shaft height

Type DINIEC

aB

bA

cHA

fAB

gAC

hH

kLB

mBA

nAA

p2–

sK

w1C

dD

d6–

IE

tGA

uF

1PH8, types of construction IM B3/IM V5, water cooling

180 1PH8184 430(16.93)

279(10.98)

15(0.59)

356(14.02)

384(15.12)

180(7.09)

670(26.38)

138(5.43)

73(2.87)

372(14.65)

14.5(0.55)

121(4.76)

65m6 M20 140(5.51)

69(2.72)

18(0.71)

1PH8186 520(20.47)

760(29.92)

225 1PH8224 445(17.52)

356(14.02)

18(0.71)

446(17.56)

474(18.66)

225(8.86)

775(30.51)

154(6.06)

88(3.46)

462(18.19)

18.5(0.73)

149(5.87)

75m6 M20 140(5.51)

79.5(3.13)

20(0.79)

1PH8226 545(21.46)

875(34.45)

1PH8228 635(25.00)

965(37.99)

280 1PH8284 684(26.93)

457(17.99)

21(0.83)

556(21.89)

588(23.15)

280(11.02)

1134(44.64)

220(8.66)

105(4.13)

574(22.60)

24(0.94)

190(7.48)

95m6 M24 170(6.69)

100(3.94)

25(0.98)

1PH8286 794(31.26)

1244(48.98)

1PH8288 924(36.38)

1374(54.09)

Terminal box type

1XB7322 1XB7422 1XB7700 1XB7712

Shaft height

Type DINIEC

pHD

p3–

rLL

x1AG

pHD

p3–

rLL

x1AG

pHD

p3–

rLL

x1AG

pHD

p3–

rLL

x1AG

180 1PH8184 484(19.06)

485(19.09)

197(7.76)

258(10.16)

539(21.22)

540(21.26)

230(9.06)

303(11.93)

588(23.15)

574(22.60)

310(12.2)

295(11.61)

– – – –

1PH8186

225 1PH8224 579(22.80)

577(22.72)

197(7.76)

258(10.16)

634(24.96)

632(24.88)

230(9.06)

303(11.93)

683(25.12)

666(26.22)

310(12.2)

295(11.61)

– – – –

1PH8226

1PH8228

280 1PH8284 709(27.91)

716(28.19)

197(7.76)

258(10.16)

724(28.5)

731(28.78)

230(9.06)

303(11.93)

770(30.31)

777(30.59)

310(12.2)

295(11.61)

820(32.28)

827(32.56)

377(14.84)

370(14.57)

1PH8286

1PH8288


© Siemens AG 2010



8/57Siemens NC 61 · 2010

8


G_P

M21

_XX

_000

011a

ml

øsae

ød

t

u

nb

g

ko

r

c

p 2p

h

d6

w1f

p3x1

G_P

M21

_XX

_000

49

ml

øsae

ød

t

u

nb

g

ko p3

ch

d6

w1f

r x1

pp 2

1PH818

1PH822

G_P

M21

_XX

_000

50

ml

øsa

e

ød

t

u

nb

g

k

ch

d6

w1f

p3or x1

pp 2

1PH828


© Siemens AG 2010


8/58 Siemens NC 61 · 2010

8




High Performance

withouthollow shaft

withhollow shaft

Shaft height

Type DINIEC

a1P

b1N

c1LA

e1M

fAB

f1T

hH

lL

kLB

kLB

kLB

1PH8, type of construction IM B5, water cooling80 1PH8083 200

(7.87)130(5.12)

12(0.47)

165(6.5)

155(6.1)

3.5(0.14)

77.5(3.05)

80(3.15)

301.5(11.87)

306.3(12.06)

319.3(12.57)

1PH8087 351.5(13.84)

356.3(14.03)

369.3(14.51)

100 1PH8101 250(9.84)

180(7.09)

16(0.63)

215(8.46)

196(7.72)

4(0.16)

98(3.86)

80(3.15)

289.5(11.4)

294.5(11.59)

312.3(12.3)

1PH8103 325(12.8)

330(12.99)

347.8(13.69)

1PH8105 384.5(15.14)

389.5(15.33)

407.3(16.04)

1PH8107 420(16.54)

425(16.73)

442.8(17.43)

132 1PH8131 340(13.39)

250(9.84)

18(0.71)

300(11.81)

260(10.24)

5(0.2)

130(5.12)

110(4.33)

347.5(13.68)

354.8(13.97)

372.8(14.68)

1PH8133 392.5(15.45)

399.8(15.74)

417.8(16.45)

1PH8135 437.5(17.22)

444.8(17.51)

462.8(18.22)

1PH8137/8 477.5(18.8)

484.8(19.09)

502.8(19.8)

DE shaft extension

Shaft height

Type DINIEC

pHD

p1–

p3–

s2–

s3–

dD

d6–

i2E

tGA

uF

80 1PH8083 213.5(8.41)

251(9.88)

– 12(0.47)

M25×1.5 32(1.25)

M12 80(3.15)

35(1.38)

10(0.39)

1PH8087

100 1PH8101 264.5(10.4)

292(11.5)

– 14(0.55)

M32×1.5 38(1.5)

M12 80(3.15)

41(1.61)

10(0.39)

1PH8103

1PH8105

1PH8107

132 1PH8131 345.5(13.6)

345(13.58)

– 18(0.71)

M50×1.5 48(1.89)

M16 110(4.33)

51.5(2.03)

14(0.55)

1PH8133

1PH8135

1PH8137/8


© Siemens AG 2010



8/59Siemens NC 61 · 2010

8


G_P

M21

_XX

_000

04

t

u

c1ød

f1i2

d6

øs2

k

ph

s3øb

1

a1

e 1

fG_PM21_XX_00047

p 1

NDE shaft extension


DE shaft extension

G_PM21_EN_00053

Ø8

(Ø0.

31)

13(0.51)

1.5(0.06)

2(0.08)

10.5

SW 19

(0.41)

4(0.16)

25.5(1.00)

32(1.26)

31(1.22)

340.05 C (1.34)

L

0.002 C

C D

M12

x1.2

5-R

H

RZ16

RZ2

560

°

Ø16

H7

(Ø0.

63H

7 )

Ø0.04 CØ0.002 C

RZ6.3

60°

Ø14

(Ø0.

55

)

Ø14

.5(Ø

0.57

)

Ø0.007 DØ0.0003 D

+0.0

08-0

.001 +0

.000

3-0

.000

04

M12

x1.2

5-LH

Ø11

4(Ø

4.49

)

0.005 D0.0002 D

18.5(0.73)

RZ6.3

1.5(0.06)

(Ø4.02)

G_P

M21

_XX

_000

79

ødøb1

t

u

k

phd6

s3

f

a1

øs2

e 1

i2c1

f1

G_PM21_XX_00047

p 1

G_PM21_XX_00048

p 1

NDE shaft extension


DE shaft extension

G_PM21_EN_00054

Ø11

.5(Ø

0.45

)

17(0.67)

1.5(0.06)

2(0.08)

10.5

SW 27

(0.41)

4(0.16)

25.5(1.00)

37(1.46)

38(1.50)

450.05 C (1.78)

L

0.002 C

C D

M16

x1.5

-RH

RZ16

RZ2

560

°

Ø20

H7

(Ø0.

79H

7 )

Ø0.04 CØ0.002 C

RZ6.3

60°

Ø18

(Ø0.

71

)

Ø18

.5(Ø

0.73

)

Ø0.007 DØ0.0003 D

+0.0

07-0

.003 +0

.000

3-0

.000

1

M16

x1.5

-LH

Ø11

4(Ø

4.49

)

0.005 D0.0002 D

18.5(0.73)

RZ6.3

1.5(0.06)

(Ø4.02)

G_P

M21

_XX

_000

78

ød

t

u

k

ph

i2

a1

d6

s3

c1

øs2

e 1

f1

øb1

f





1PH810

1PH813



© Siemens AG 2010

Asynchronous motorsDimensional drawings1PH8 motorsSH 100/SH 132 – Water cooling

8/60 Siemens NC 61 · 2010

8




High Performance

withouthollow shaft

with hollow shaft

Shaft height

Type DINIEC

aB

a1P

bA

b1N

cHA

c1LA

e1M

fAB

f1T

hH

lL

kLB

kLB

kLB

mBA


100 1PH8101 167(6.57)

250(9.84)

160(6.3)

180(7.09)

11(0.43)

16(0.63)

215(8.46)

196(7.72)

4(0.16)

100(3.94)

80(3.15)

289.5(11.4)

294.5(11.59)

312.3(12.3)

37(1.46)

1PH8103 202.5(7.97)

325(12.8)

330(12.99)

347.8(13.69)

1PH8105 262(10.31)

384.5(15.14)

389.5(15.33)

407.3(16.04)

1PH8107 297.5(11.71)

420(16.54)

425(16.73)

442.8(17.43)

132 1PH8131 220.5(8.68)

340(13.39)

216(8.5)

250(9.84)

15(0.59)

18(0.71)

300(11.81)

260(0.2)

5(0.2)

132(5.2)

110(4.33)

347.5(13.68)

354.8(13.97)

372.8(14.68)

42(1.65)

1PH8133 265.5(10.45)

392.5(15.45)

399.8(15.74)

417.8(16.45)

1PH8135 310.5(12.22)

437.5(17.22)

444.8(17.51)

462.8(18.22)

1PH8137/8 350.5(13.8)

477.5(18.8)

484.8(19.09)

502.8(19.8)

DE shaft extension

Shaft height

Type DINIEC

m1–

m2–

nAA

pHD

p1–

p2–

p3–

sK

s2–

s3–

w1C

dD

d6–

i2E

tGA

uF

100 1PH8101 68(2.68)

12(0.47)

43(1.69)

266.5(10.49)

294(11.57)

198(7.8)

276.5(10.89)

12(0.47)

14(0.55)

M32×1.5 43(1.69)

38(1.5)

M12 80(3.15)

41(1.61)

10(0.39)

1PH8103

1PH8105

1PH8107

132 1PH8131 81(3.19)

12(0.47)

43(1.69)

347(13.66)

347(13.66)

262(10.3)

357.5(14.07)

12(0.47)

18(0.71)

M50×1.5 53(2.09)

48(1.89)

M16 110(4.33)

51.5(2.03)

14(0.55)

1PH8133

1PH8135

1PH8137/8


© Siemens AG 2010


1PH8 motorsSH 100/SH 132 – Water cooling

8/61Siemens NC 61 · 2010

8


G_P

M21

_XX

_000

10a

ød

t

u

k

p

h

møs

a

cm2

m1

nb

i2

a1

d6

w1

s3

c1

f1 øs2

e 1

øb1

f

p 2h

p3

G_PM21_XX_00047

p 1

G_PM21_XX_00048

p 1

NDE shaft extension


DE shaft extension

G_PM21_EN_00054

Ø11

.5(Ø

0.45

)

17(0.67)

1.5(0.06)

2(0.08)

10.5

SW 27

(0.41)

4(0.16)

25.5(1.00)

37(1.46)

38(1.50)

450.05 C (1.78)

L

0.002 C

C D

M16

x1.5

-RH

RZ16

RZ2

560

°

Ø20

H7

(Ø0.

79H

7 )

Ø0.04 CØ0.002 C

RZ6.3

60°

Ø18

(Ø0.

71

)

Ø18

.5(Ø

0.73

)

Ø0.007 DØ0.0003 D

+0.0

07-0

.003 +0

.000

3-0

.000

1

M16

x1.5

-LH

Ø11

4(Ø

4.49

)

0.005 D0.0002 D

18.5(0.73)

RZ6.3

1.5(0.06)

(Ø4.02)

G_P

M21

_XX

_000

72

ødøb1

t

u

k

p 2p

hd6

s3

f

p3

a1

c

e 1

i2c1

f1

nb øs

2

møs

a

m2m1

w1





© Siemens AG 2010


8/62 Siemens NC 61 · 2010

8



D400 D450 D550 D660 D400 D450 D550 D660 D400 D450 D550 D660

Shaft height

Type DINIEC

aB

a1P

bA

b1N

cHA

c1LA

e1M

1PH8, types of construction IM B35/IM B5/IM V15, water cooling180 1PH8184 430

(16.93)400(15.75)

450(17.72)

– – 279(10.98)

300(11.81)

350(13.78)

– – 15(0.59)

16(0.63)

350(13.78)

400(15.75)

– –

1PH8186 520(20.47)

225 1PH8224 445(17.52)

– – 550(21.65)

– 356(14.02)

– – 450(17.72)

– 18(0.71)

20(0.79)

– – 500(19.69)

–

1PH8226 545(21.46)

1PH8228 635(25.00)

280 1PH8284 684(26.93)

– – – 660(26.98)

457(17.99)

– – – 550(21.65)

21(0.83)

24(0.94)

– – – 600(23.62)

1PH8286 794(31.26)

1PH8288 924(36.38)

DE shaft extension

Shaft height

Type DINIEC

fAB

f1T

gAC

hH

i2EB

kLB

mBA

nAA

p2–

sK

w1C

dD

d6–

IE

tGA

uF

180 1PH8184 356(14.02)

5(0.20)

384(15.12)

180(7.09)

125(4.92)

670(26.38)

123(4.84)

73(2.87)

372(14.65)

14.5(0.57)

121(4.76)

65m6 M20 140(5.51)

69(2.72)

18(0.71)

1PH8186 760(29.92)

255 1PH8224 446(17.56)

5(0.20)

474(18.66)

225(8.86)

125(4.92)

770(30.31)

144(5.67)

88(3.46)

462(18.19)

18.5(0.73)

149(5.87)

75m6 M20 140(5.51)

79.5(3.13)

20(0.79)

1PH8226 872(34.33)

1PH8228 962(37.87)

280 1PH8284 556(21.89)

6(0.24)

588(23.15)

280(11.02)

140(5.51)

1134(44.65)

220(8.66)

105(4.13)

574(22.60)

24(0.94)

190(7.48)

95m6 M24 170(6.69)

100(3.94)

25(0.98)

1PH8286 1244(48.98)

1PH8288 1374(54.09)

Terminal box type

1XB7322 1XB7422 1XB7700 1XB7712

Shaft height

Type pHD

p3–

rLL

x1AG

pHD

p3–

rLL

x1AG

pHD

p3–

rLL

x1AG

pHD

p3–

rLL

x1AG

180 1PH8184 484(19.06)

485(19.09)

197(7.76)

258(10.16)

539(21.22)

540(21.26)

230(9.06)

303(11.93)

588(23.15)

574(22.60)

310(12.2)

295(11.61)

– – – –

1PH8186

225 1PH8224 579(22.80)

577(22.72)

197(7.76)

258(10.16)

634(24.96)

632(24.88)

230(9.06)

303(11.93)

683(25.12)

666(26.22)

310(12.2)

295(11.61)

– – – –

1PH8226

1PH8228

280 1PH8284 709(27.91)

716(28.19)

197(7.76)

258(10.16)

724(28.5)

731(28.78)

230(9.06)

303(11.93)

770(30.31)

777(30.59)

310(12.2)

295(11.61)

820(32.28)

827(32.56)

377(14.84)

370(14.57)

1PH8286

1PH8288


© Siemens AG 2010



8/63Siemens NC 61 · 2010

8


G_P

M21

_XX

_000

15a

ml

øsae

ød

t

u

nb

g

ko

c

p 2p

h

d6

w1

e 1

a1øb1

c1f1

f

p3r x1

G_P

M21

_XX

_000

51

ml

øsae

ød

t

u

nb

g

ko

c

pp 2

h

d6

w1f

øb1

øa1

c1f1 r

p3x1

e1

1PH818

1PH822

ml

øsae

ød

t

u

nb

g

ko

ch

d6

w1f

øb1

øa1

c1f1

e1

r

G_P

M21

_XX

_000

52p3x1

pp 2

1PH828


© Siemens AG 2010

Asynchronous motorsDimensional drawings1PH7 motorsForced ventilation

8/64 Siemens NC 61 · 2010

8


For deviating and additional dimensions of 1PH7 motors with DRIVE-CLiQ, see 1PH7 motors with DRIVE-CLiQ.


Shaft height

Type DINIEC

aB

bA

cLA

eM

fAB

hH

kLB

k1–

mBA

m1–

m2–

nAA

pHD

sK

s3–


100 1PH71011PH7103

202.5(7.97)

160(6.30)

11(0.43)

263(10.35)

196(7.72)

100(3.94)

411(16.18)

434(17.09)

52(2.05)

64(2.52)

27(1.06)

39(1.54)

220(8.66)

12(0.47)

PG29/M32

1PH71051PH7107

297.5(11.71)

358(14.09)

506(19.92)

529(20.83)

132 1PH71311PH7133

265.5(10.45)

216(8.50)

14(0.55)

341(13.43)

260(10.24)

132(5.20)

538(21.18)

561(22.09)

63(2.48)

75(2.95)

33(1.30)

52(2.05)

275(10.83)

12(0.47)

PG36/M40

1PH71351PH7137

350.5(13.80)

426(16.77)

623(24.53)

646(25.43)

160 1PH7163 346.5(13.64)

254(10.00)

17(0.67)

438(17.24)

314(12.36)

160(6.30)

640(25.20)

663(26.10)

78(3.07)

81(3.19)

42(1.65)

62(2.44)

330(12.99)

14(0.55)

PG42/M50

1PH7167 406.5(16.00)

498(19.61)

700(27.56)

723(28.46)

DE shaft extension

Shaft height

Type DINIEC

w1C

dD

d6–

IE

tGA

uF

100 1PH71011PH71031PH71051PH7107

40(1.57)

38(1.5)

M12 80(3.15)

41(1.61)

10(0.39)

132 1PH71311PH71331PH71351PH7137

50(1.97)

42(1.65)

M16 110(4.33)

45(1.77)

12(0.47)

160 1PH71631PH7167

64(2.52)

55(2.17)

M20 110(4.33)

59(2.32)

16(0.63)

G_DA65_XX_00146a

t

l

uPG11/M16

s sm1

ae

m

w1

h

d6

m2

s3

fb

n

pc

kk1

d

1PH7101PH7131PH716


© Siemens AG 2010


1PH7 motorsForced ventilation

8/65Siemens NC 61 · 2010

8


For motor Dimensions in mm (in) Terminal box type1XB7322

Shaft height

Type DINIEC

aB

bA

cLA

eM

fAB

gAC

hH

kLB

k1–

mBA

m1–

m2–

nAA

o–

p HD

1PH7, type of construction IM B3, forced ventilation, direction of air flow DE → NDE

180 1PH7184 430(16.93)

279(10.98)

14(0.55)

510(20.08)

360(14.17)

408(16.09)

180(7.09)

835(32.87)

– 60(2.36)

120(4.72)

35(1.38)

65(2.56)

541(21.3)

495(19.49)

1PH7186 520(20.47)

600(23.62)

925(36.42)

631(24.84)

225 1PH7224 445(17.52)

356(14.02)

18(0.71)

530(20.87)

450(17.72)

498(19.61)

225(8.86)

– 1100(43.31)

60(2.36)

120(4.72)

40(1.57)

85(3.35)

629(24.76)

595(23.43)

DE shaft extension

Shaft height

Type DINIEC

sK

w1C

dD

d6–

IE

tGA

uF

180 1PH7184 14.5(0.57)

121(4.76)

60(2.36)

M20 140(5.51)

64(2.52)

18(0.72)

1PH7186 65(2.56)

69(2.72)

225 1PH7224 18.5(0.73)

149(5.87)

75(2.95)

M20 140(5.51)

79.5(3.13)

20(0.79)

ae

m2

mw1

m1

g

l

kk1

o

u

t

d6

fb

n s

h

cp

d

AO

AO

AI

AI

G_DA65_EN_00147a

Al air inletAO air outlet

1PH7181PH7224


© Siemens AG 2010


8/66 Siemens NC 61 · 2010

8


For motor Dimensions in mm (in) Terminal box type1XB7322

Shaft height

Type DINIEC

aB

bA

cLA

eM

fAB

gAC

hH

kLB

mBA

m1–

m2–

nAA

o–

p HD

1PH7, type of construction IM B3, forced ventilation, direction of air flow NDE → DE

180 1PH7184 430(16.93)

279(10.98)

14(0.55)

510(20.08)

360(14.17)

405(15.94)

180(7.09)

1010(39.76)

60(2.36)

120(4.72)

35(1.38)

65(2.56)

541(21.3)

495(19.49)

1PH7186 520(20.47)

600(23.62)

1100(43.31)

631(24.84)

225 1PH7224 445(17.52)

356(14.02)

18(0.71)

530(20.87)

450(17.72)

498(19.61)

225(8.86)

1090(42.91)

60(2.36)

120(4.72)

40(1.57)

85(3.35)

629(24.76)

595(23.43)

DE shaft extension

Shaft height

Type DINIEC

sK

w1C

dD

d6–

IE

tGA

uF

180 1PH7184 14.5(0.57)

121(4.76)

60(2.36)

M20 140(5.51)

64(2.52)

18(0.71)

1PH7186 65(2.56)

69(2.72)

225 1PH7224 18.5(0.73)

149(5.87)

75(2.95)

M20 140(5.51)

79.5(3.13)

20(0.79)

ae

mm

w

m

l

ko

u

td

fb

n sh

cp

d

6

2

1

1

g

AI

AI

AO

AO

G_DA65_EN_00148b


1PH718

ae

m2

mw1

m1

g

l

ko

u

t

fb

n s

h

cp

d

d6

c n

AI

AO

AOG_DA65_EN_00183

AI

1PH7224



© Siemens AG 2010



8/67Siemens NC 61 · 2010

8




Shaft height

Type DINIEC

a1P

b1N

c1LA

e1M

fAB

f1T

i2–

kLB

k1–

pHD

s2S

s3–


100 1PH71011PH7103

250(9.84)

180(7.09)

10(0.39)

215(8.46)

196(7.72)

4(0.16)

80(3.15)

411(16.18)

434(17.09)

218(8.58)

14(0.55)

PG29/M32

1PH71051PH7107

506(19.92)

529(20.83)

132 1PH71311PH7133

350(13.78)

250(9.84)

16(0.63)

300(11.81)

260(10.24)

5(0.2)

110(4.33)

538(21.18)

561(22.09)

273(10.75)

18(0.71)

PG36/M40

1PH71351PH7137

623(24.53)

646(25.43)

DE shaft extension

Shaft height

Type DINIEC

dD

d6–

IE

tGA

uF

100 1PH71011PH7103

38(1.5)

M12 80(3.15)

41(1.61)

10(0.39)

1PH71051PH7107

132 1PH71311PH7133

42(1.65)

M16 110(4.33)

45(1.77)

12(0.47)

1PH71351PH7137

k

G_DA65_XX_00150a

p

a1

e1

s2

u

s3PG11/M16

t

l

f1

c1

d6

i2

f

k1

b1 d

1PH7101PH713


© Siemens AG 2010


8/68 Siemens NC 61 · 2010

8




Shaft height

Type DINIEC

aB

a1P

bA

b1N

cLA

e1M

fAB

f1T

hH

i2–

kLB

k1–

mBA

m1–

m2–

nAA

pHD


100 1PH71011PH7103

202.5(7.97)

250(9.84)

160(6.3)

180(7.09)

11(0.43)

215(8.46)

196(7.72)

4(0.16)

100(3.94)

80(3.15)

411(16.18)

435(17.13)

52(2.05)

64(2.52)

27(1.06)

39(1.54)

220(8.66)

1PH71051PH7107

297.5(11.71)

506(19.92)

529(20.83)

132 1PH71311PH7133

265.5(10.45)

350(13.78)

216(8.5)

250(9.84)

14(0.55)

300(11.81)

260(10.24)

5(0.2)

132(5.2)

110(4.33)

538(21.18)

561(22.09)

63(2.48)

75(2.95)

33(1.3)

52(2.05)

275(10.83)

1PH71351PH7137

350.5(13.8)

623(24.53)

646(25.43)

160 1PH7163 346.5(13.64)

400(15.75)

254(10)

300(11.81)

17(0.67)

350(13.78)

314(12.36)

5(0.2)

160(6.3)

110(4.33)

640(25.2)

663(26.1)

78(3.07)

81(3.19)

42(1.65)

62(2.44)

330(12.99)

1PH7167 406.5(16)

700(27.56)

723(28.46)

DE shaft extension

Shaft height

Type DINIEC

sK

s2S

s3–

w1C

dD

d6–

IE

tGA

uF

100 1PH71011PH71031PH71051PH7107

12(0.47)

14(0.55)

PG29/M32 40(1.57)

38(1.5)

M12 80(3.15)

41(1.61)

10(0.39)

132 1PH71311PH71331PH71351PH7137

12(0.47)

18(0.71)

PG36/M40 50(1.97)

42(1.65)

M16 110(4.33)

45(1.77)

12(0.47)

160 1PH71631PH7167

14(0.47)

18(0.71)

PG42/M50 64(2.52)

55(2.17)

M20 110(4.33)

59(2.32)

16(0.63)

bG_DA65_XX_00151a

PG11/M16 s3

k

s2

f1

f

a1

e1

u

t

l

ss

i2

h

m2w1

m1m

a

p

d6

n

k1

c

b1 d

1PH7101PH7131PH716


© Siemens AG 2010



8/69Siemens NC 61 · 2010

8


For motor Dimensions in mm (in) For dimensions for foot mounting, shaft and terminal box,see dimensional drawing of 1PH718 and 1PH7224 motors, type of construction IM B3.

Terminal box type1XB7322

Shaft height

Type DINIEC

a1P

b1N

c1LA

e1M

f1T

hH

kLB

k1– p

z–

α–

1PH7, type of construction IM B35, forced ventilation, direction of air flow DE → NDE

180 1PH71841) 400(15.75)

300(11.81)

15(0.59)

350(13.78)

5(0.2)

180(7.09)

835(32.87)

– 495(19.49)

4 45°

1PH71841) 450(17.72)

350(13.78)

16(0.63)

400(15.75)

835(32.87)

8 22.5°

1PH7186 925(36.42)

225 1PH7224 550(21.65)

450(17.72)

18(0.71)

500(19.69)

5(0.2)

225(8.86)

– 1100(43.31)

595(23.43)

8 22.5°

e1

a 1

h

kk1

p

f1

z x c1

b1

G_DA65_EN_00152C

19 (0.75)1PH7181PH7224

1) For flange selection, see order number supplement for SH 180 and SH 225.


© Siemens AG 2010


8/70 Siemens NC 61 · 2010

8


For motor Dimensions in mm (in) For dimensions for foot mounting, shaft and terminal box,see dimensional drawing of 1PH718 and 1PH7224 motors, type of construction IM B3.

Terminal box type 1XB7322

Shaft height

Type DINIEC

a1P

b1N

c1LA

e1M

f1T

hH

kLB

–p

z–

α–

1PH7, type of construction IM B35, forced ventilation, direction of air flow NDE → DE

180 1PH71841) 400(15.75)

300(11.81)

15(0.59)

350(13.78)

5(0.2)

180(7.09)

1010(39.76)

495(19.49)

4 45°

1PH71841) 450(17.72)

350(13.78)

16(0.63)

400(15.75)

1010(39.76)

8 22.5°

1PH7186 1100(43.31)

225 1PH7224 550(21.65)

450(17.72)

18(0.71)

500(19.69)

5(0.2)

225(8.86)

1090(42.91)

595(23.43)

8 22.5°

e

h

k

p

f1

z x c1

b 1a1

1

AI

AIAO

AO

G_DA65_EN_00153c

19 (0.75)


1PH718

e

1

h

k

p

f 1

z x 19

c

1

b 1

a 1

AI

AI

AO

AO

G_DA65_EN_00184a

(0.75)1PH7224


1) For flange selection, see order number supplement for SH 180 and SH 225.


© Siemens AG 2010


1PH7 motors with DRIVE-CLiQForced ventilation

8/71Siemens NC 61 · 2010

8



Shaft height

Type DINIEC

kLB

k1–

p1–

x–

y–

Deviating and additional dimensions for 1PH7 motors with DRIVE-CLiQ to those given in dimension tables 1PH7, forced ventilation

100 1PH71011PH7103

411(16.18)

453(17.83)

81(3.19)

52.5(2.07)

63.5(2.50)

1PH71051PH7107

506(19.92)

548(21.57)

132 1PH71311PH7133

538(21.18)

580(22.83)

103.5(4.07)

66(2.60)

63.5(2.50)

1PH71351PH7137

623(24.53)

665(26.18)

160 1PH7163 640(25.20)

682(26.85)

127(5.00)

75(2.95)

63.5(2.50)

1PH7167 700(27.56)

742(29.21)

k

k

p 1

28

1 y

x

14

320° rotatable

G_D

A65

_EN

_001

89a

(1.1

0)

(0.55)

1PH7101PH7131PH716


© Siemens AG 2010

Asynchronous motorsDimensional drawings1PH4 motorsWater cooling

8/72 Siemens NC 61 · 2010

8



Shaft height

Type DINIEC

aB

a1P

bA

b1N

cLA

c1–

e1–

fAB

f1T

hH

i2–

kLB

mBA

m1–

m2–

nAA


100 1PH4103 349(13.74)

250(9.84)

160(6.30)

180(7.09)

11(0.43)

12(0.47)

215(8.46)

190(7.48)

4(0.16)

100(3.94)

80(3.15)

416(16.38)

35(1.38)

60(2.36)

24(0.94)

40(1.57)

1PH4105 409(16.10)

476(18.74)

1PH4107 474(18.66)

541(21.30)

132 1PH4133 377(14.84)

350(13.78)

216(8.50)

250(9.84)

14(0.55)

16(0.63)

300(11.81)

245(9.65)

5(0.20)

132(5.20)

110(4.33)

458(18.03)

36(1.42)

85(3.35)

24(0.94)

43(1.69)

1PH4135 447(17.60)

528(20.79)

1PH4137 497(19.57)

578(22.76)

1PH4138 532(20.94)

613(24.13)

DE shaft extension

Shaft height

Type DINIEC

o–

pHD

sK

s2K

s3–

w1C

dD

d6–

IE

tGA

uF

100 1PH4103 244(9.61)

259(10.20)

12(0.47)

14(0.55)

PG29 44(1.73)

38(1.50)

M12 80(3.15)

41(1.61)

10(0.39)

1PH4105 304(11.97)

1PH4107 369(14.53)

132 1PH4133 264(10.39)

334.5(13.17)

12(0.47)

18(0.71)

PG36 53(2.09)

42(1.77)

M16 110(4.33)

45(1.77)

12(0.47)

1PH4135 334(13.15)

1PH4137 384(15.12)

1PH4138 419(16.50)

a

d

d6

b 1

ko

c1

i2

l

m2

m1

m

f1

s3

h

s2

e1

na1 b

f

t

u

p

c

Ø sw1

A

A

Water connectionG 1/4 with 1PH410G 3/8 with 1PH413

Water connectionG 1/4 with 1PH410G 3/8 with 1PH413

G_DA65_EN_00164a

1PH4101PH413


© Siemens AG 2010


1PH4 motorsWater cooling

8/73Siemens NC 61 · 2010

8



Shaft height

Type DINIEC

aB

a1P

bA

b1N

cLA

c1–

e1–

fAB

f1T

hH

i2–

kLB

mBA

m1–

m2–

nAA


160 1PH4163 508(20.00)

400(15.75)

254(10.00)

300(11.81)

15(0.59)

18(0.71)

350(13.78)

294(11.57)

5(0.20)

160(6.30)

110(4.33)

591(23.27)

44(1.73)

77(3.03)

29(1.14)

49(1.93)

1PH4167 563(22.17)

646(25.43)

1PH4163 608(23.94)

691(27.20)

DE shaft extension

Shaft height

Type DINIEC

o–

pHD

sK

s2K

s3–

w1C

dD

d6–

IE

tGA

uF

160 1PH4163 407(16.02)

388(15.28)

14(0.55)

18(0.71)

PG36 56(2.20)

55(2.17)

M20 110(4.33)

59(2.32)

16(0.63)

1PH4167 462(18.19)

1PH4168 507(19.96)

a

d

d6

b 1

ko

c1

i2

l

s

m2

m1

m

f1

s3

h

s2

e1

na1 b

f

t

u

p

c

∅

w1

A

A

Water connection G 1/2 Water connection G 1/2

G_D

A65

_EN

_001

65

1PH416


© Siemens AG 2010

Asynchronous motorsDimensional drawings1PH7 motors with two-speed gearboxForced ventilation

8/74 Siemens NC 61 · 2010

8


Dimensions for 1PH7184, 1PH7186 and 1PH7224 on request.

For motor GearboxDimensions in mm (in)

Shaft height

Type A B C C1 D1 D2 D3 D4 E1 E2 F H

1PH7 with two-speed gearbox, type of construction IM B35, forced ventilation100 1PH7101

1PH71031PH71051PH7107

55(2.17)

184(7.24)

12(0.47)

18(0.71)

100(3.94)

100(3.94)

188(7.40)

190(7.48)

215(8.46)

80(3.15)

208(8.19)

108(4.25)

132 1PH71311PH71331PH71351PH7137

58(2.28)

234(9.21)

12(0.47)

20(0.79)

116(4.57)

118(4.65)

249(9.80)

250(9.84)

300(11.81)

100(3.94)

270(10.63)

136(5.35)

160 1PH71631PH7167

58(2.28)

290(11.42)

17(0.67)

20(0.79)

140(5.51)

130(5.12)

249(9.80)

250(9.84)

350(13.78)

100(3.94)

326(12.83)

164(6.46)

GearboxDimensions in mm (in)

Total lengthmotor-gearbox

Shaft height

Type K1 L1 L2 P S S2 S3 Z W K

100 1PH71011PH7103

298(11.73)

– 116(4.57)

301(11.85)

14(0.55)

14(0.55)

M8 8 63(2.48)

709(27.91)

1PH71051PH7107

804(31.65)

132 1PH71311PH7133

346.5(13.64)

129.5(5.10)

142.5(5.61)

346(13.62)

14(0.55)

18(0.71)

M12 12 71(2.80)

885(34.84)

1PH71351PH7137

970(38.19)

160 1PH7163 346.5(13.64)

– 142.5(5.61)

402(15.83)

14(0.55)

18(0.71)

M12 12 71(2.80)

987(38.86)

1PH7167 1024(40.31)

$ Switching unit (lifting solenoid 24 V DC, 5 A).% Ventilation valve.& Oil filling bolt.4A Oil level inspection window or oil return for counterclockwise rotation

and circulating-oil lubrication.4B Oil level inspection window or oil return for clockwise rotation

and circulating-oil lubrication.

) Oil drain bolt for type of construction IM B35.6A Oil inlet for clockwise rotation and circulating-oil lubrication.6B Oil inlet for counterclockwise rotation and circulating-oil lubrication.+ Oil inlet for type of construction IM V15 (must be connected)., Oil inlet for type of construction IM V36.- Connector, manufacture: Harting, type HAN 8 U.

E2

E1

BF

HC

P

WK1

L1SSA L2

K

S2

D1

D2

D3

C1

1

3

4B

56A

7

2

7

9

32

8

4A

6B 5

4A

Z x S3

6A

D4(Cen

terin

g)

G_DA65_EN_00166a


© Siemens AG 2010


1PH4 motors with two-speed gearboxWater cooling

8/75Siemens NC 61 · 2010

8



Shaft height

Type A B C C1 D1 D2 D3 D4 E1 E2 F H

1PH4 with two-speed gearbox, type of construction IM B35, water cooling

100 1PH4103

1PH4105

1PH4107

55(2.17)

184(7.24)

12(0.47)

18(0.71)

100(3.94)

100(3.94)

188(7.40)

190(7.48)

215(8.46)

80(3.15)

208(8.19)

108(4.25)

132 1PH4133

1PH4135

1PH4137

1PH4138

58(2.28)

234(9.21)

12(0.47)

20(0.79)

116(4.57)

118(4.65)

249(9.80)

250(9.84)

300(11.81)

100(3.94)

270(10.63)

136(5.35)

160 1PH4163

1PH4167

1PH4168

58(2.28)

290(11.42)

17(0.67)

20(0.79)

140(5.51)

130(5.12)

249(9.80)

250(9.84)

350(13.78)

100(3.94)

326(12.83)

164(6.46)

GearboxDimensions in mm (in)

Total lengthmotor-gearbox

Shaft height

Type K1 L1 L2 P S S2 S3 Z W K

100 1PH4103 298(11.73)

– 116(4.57)

301(11.85)

14(0.55)

14(0.55)

M8 8 63(2.48)

714(28.11)

1PH4105 774(30.47)

1PH4107 839(33.03)

132 1PH4133 346.5(13.64)

129.5(5.10)

142.5(5.61)

346(13.62)

14(0.55)

18(0.71)

M12 12 71(2.80)

805(31.69)

1PH4135 875(34.45)

1PH4137 925(36.42)

1PH4138 960(37.80)

160 1PH4163 346.5(13.64)

– 142.5(5.61)

402(15.83)

14(0.55)

18(0.71)

M12 12 71(2.80)

938(36.93)

1PH4167 993(39.09)

1PH4168 1038(40.87)

E2

E1

BF

HP

C

WK1

L1SSA L2

K

S2

D1

D2

D3

C1

Z x S3

D4

(Cen

terin

g)

G_NC01_EN_00396


© Siemens AG 2010

Asynchronous motorsDimensional drawings1PH2 motorsWater cooling

8/76 Siemens NC 61 · 2010

8


■


Type Standardspindlediameter

Rotorinternaldiameter

Statorouterdiameter

Total outer diameter

Total length

d di DA D L

1PH2 built-in motors, water cooling

1PH2093 67(2.64)

85(3.35)

180(7.09)

205(8.07)

250(9.84)

1PH2095 300(11.81)

1PH2113 82(3.23)

100(3.94)

220(8.66)

250(9.84)

290(11.42)

1PH2115 310(12.20)

1PH2117 330(12.99)

1PH2118 390(15.35)

G_N

C01

_XX

_000

18


© Siemens AG 2010

Documents

motion-control NC61 chap08 English 2010.book Seite 1 ... · PDF fileSiemens NC 61 · 2010 8/2 Introduction 8/4 1PH8 motors With solid shaft/hollow shaft ... Rated torque Mrated Selection