MOP SIU Replacement_VNP2 _RevD.pdf

INSTRUCTION

1 (11) Prepared (also subject responsible if other) No.

Lai Le Approved Checked Date Rev Reference

2014-07-25 A

MOP SIU REPLACEMENT FOR VNP2

Section Page 1 LAPTOP SETUP: ................................................................................... 2 2 BACKUP SIU CONFIGURATION FILE (XML) TO LAPTOP. .................. 3 3 SITE SPECIFIC STEP-BY-STEP ........................................................... 4 4 SWAP SIU HARDWARE ...................................................................... 10

This MOP describes the procedure to replace all SIUs with productRevision=R1G on live network VNP2. The procedure is used the step by step for backup a configuration on one SIU and then restore this configuration on another SIU which will replace in. For here, ASP/SUB will be easy implement SIU replacement, and also less impact to customer services.

Important notes for ASP/SUB: - Be sure to have the correct SIU Software (T12B_ CXP 102 138/1 R2AB). This software will be getting from

E///. - Laptop must be working well. - Ethernet cable. - Software supports SSH/Telnet (Puty or Secure CRT). - Software supports SFTP server (should be used Core FTP mini). - Site specific configuration (xml file) backup file included in this procedure. - Make sure replaced new SIU is different version R1G.

Once you have had the correct SIU software and backup file, extract those to a folder off your PC in C:\ SIU. If you havent already created a SIU folder off your C:\ drive.

INSTRUCTION



2014-07-25 A

1 LAPTOP SETUP:

SETUP Description

NOTE: If you have any problems with any steps of this MOP, DO NOT PROCEED, Contact your PM immediately.

The Steps below need to be executed in the specified sequence on all impacted nodes.

SET COMPUTER IP TO:

192.168.1.2

255.255.255.0

192.168.1.1

Setup a telnet session for connecting to SIU local console port:

SIU IP address: 192.168.1.1

login: admin password: hidden

LAUNCH FTP PROGRAM (User: siu ; Pass: siu) & Port: 22

1. Double click on the file msftpsrvr.exe to start the mini-sftp server program on your PC.

2. Change these values on the mini-sftp-server as below

3. The password is

4. Then click on start button to start the SFTP server

INSTRUCTION



2014-07-25 A

2 BACKUP SIU CONFIGURATION FILE (XML) TO LAPTOP.

(Activities on existing SIU)

Step Description

Backup SIU xml file to Laptop

1 Login to SIU will be replaced:

ssh [email protected]

Pass: hidden

Setting ly logfile th 1, file lu theo quy tc SIU_HCxxxx_old.log

xxxx: l s c th ca trm .

2 Check Product Revision and Serial code

OSmon> getmoattribute STN=0,Equipment=0

STN=0,Equipment=0; instanceId= 0;

STN=0,Equipment=0; serialNumber= CB4H230708;

STN=0,Equipment=0; productRevision= R1G; (or: R1G/A; R1E/C)

STN=0,Equipment=0; productNumber= KDU 137 596/2;

STN=0,Equipment=0; manufacturingDate= 20110404;

OperationSucceeded

Note: Product Revisions are R1G; R1G/A; R1E/C must be replaced by another one.

3

Check alarm SIU

OSmon> getalarmlist

OperationSucceeded

Note: Please capture/get alarm screen on existing SIU.

4

OSmon> getmoattribute stn=0

OSmon> getmoattribute

INSTRUCTION



2014-07-25 A

5

OSmon> getmoattribute STN=0,TGTransport=all

STN=0,TGTransport=HC1047_TG900; instanceId= HC1047_TG900;

STN=0,TGTransport=HC1047_TG900; operationalState= enabled;

STN=0,TGTransport=HC1047_TG900; PGW_IP_Address= 10.213.240.195;

STN=0,TGTransport=HC1047_TG900; depIP_Interface= STN=0,IPInterface=2G;

STN=0,TGTransport=HC1047_TG900; STN_PGW_LinkStatus= up;

STN=0,TGTransport=HC1047_TG900; overloadThreshold= 1000;

STN=0,TGTransport=HC1047_TG900; overloadReportInterval= 1;

STN=0,TGTransport=HC1047_TG900; DSCP_L2TP_CP= 40;

OperationSucceeded

====> From here, we can know this SIU has used for 2G or not, and know whats

2G ID.

4

Backup the SIU xml configuration to Laptop OSmon> uselocalsftp on

OperationSucceeded

OSmon> startSession bcm1 OperationSucceeded

OSmon> backup bcm1 sftp://siu:[email protected]/SIU/SIU_HCxxx.xml admin OperationSucceeded

OSmon> getsessionstatus bcm1

UploadCompleted OperationSucceeded

OSmon> endSession bcm1

A backup xml file will appear at path on laptop: C/SIU/

This backup xml file will used to restore for replaced new SIU.

3 SITE SPECIFIC STEP-BY-STEP

(Activities on new SIU)

1.

- Power cables are connected temporary to new SIU from PWR out 2 port of RBS 6601.

- Check the power LED indicator is lit.

- Connect an Ethernet cable from the laptop port to the Console port on the SIU.

Heres 2G ID.

INSTRUCTION



2014-07-25 A

2.

The SIU local maintenance IP address is 192.168.1.1 (Sub netmask 255.255.255.0).

login: admin

Password: hidden

3.

Reset SIU to factory setting. (Ch thc hin trn con SIU mi) OSmon> resetToFactorySetting Warning: All user settings will be removed, continue (ok/cancel)? OK. OperationSucceeded

4.

Re-Login SIU:

Setting ly logfile th 2, file lu theo quy tc SIU_HCxxxx_before_upgrade.log

5.

Check current HW revision OSmon> getmoattribute STN=0,Equipment=0 STN=0,Equipment=0; instanceId= 0; STN=0,Equipment=0; serialNumber= CB4B682659; STN=0,Equipment=0; productRevision= R1E/D; ===============> Revision OK. STN=0,Equipment=0; productNumber= KDU 137 596/2; STN=0,Equipment=0; manufacturingDate= 20100111; OperationSucceeded

The new SIU has productRevision must be different with R1G; R1G/A; R1E/C.

INSTRUCTION



2014-07-25 A

6.

Check current SIU Software (Check the current SIU software level as follows)

OSmon> rev ------------------- OSE modules ------------------------------------------ oam.chk Operation & Maintenance R2J01 secmgrr.chk Security Manager R2G02 inetr.chk MLPPP Daemon R2D03 ltp.chk Local Terminal Port R2D03 snc.chk Synchronization R2H02 pd.chk Packet Distributor R1L_1 cesopsn_pwr.chk Circuit Emulation Service R1F03 hdlc_pwr.chk HDLC Pseudo-Wire Emulation R1H07 p_relayr.chk Packet Relay R2H01 profiler.chk System Profiler R1L_1 hwtest.chk Hardware Tester P2A01 lcf_cp.chk Local Connectivity Function R1C01 bsp.drv Board Support Package R2H02 bootstrap.chk Bootstrap R2G02 loader.drv Software Loader R1L_1 linuxload.drv Linux Loader R2H02 ------------------- Firmware modules ------------------------------------- PBOOT CXC 112 3777/1 R1G02 ------------------- Software archives ------------------------------------ Primary: OSE CXP102128_1 R2J01 Linux - R2J01 Backup: OSE CXP102084_1 R3F01 ------------------- Active software -------------------------------------- OSE Primary Linux Primary

In this case: CXP102128_1 (R2J01) is version T11B, old version. So, We must be upgraded to correct SW T12B: CXP 102 138/1 R2AB as step 7.

INSTRUCTION



2014-07-25 A

7.

Upgrade SIU Software step by step:

The software upgrade requires a SFTP server running on your PC. The software and configuration files will be downloaded from your PC to the SIU.

Start the SFTP server on your PC and configure it with the username and password siu and set Root path to c:

Enter the following commands:

OSmon> uselocalsftp on

OSmon> startswsession 1 OperationSucceeded

OSmon> downloadsw 1 sftp://siu:[email protected]/SIU/T12B_siu02_sw.tar OperationSucceeded

OSmon> getswsessionstatus 1 DownloadInProgress OperationSucceeded

Wait up to 5 minutes for the software download to complete.

OSmon> getswsessionstatus 1 DownloadCompleted OperationSucceeded

When the software download is completed, activate the software using the following command:

OSmon> activatesw 1 OperationSucceeded

The SIU will restart and connectivity will be lost.

INSTRUCTION



2014-07-25 A

8.

Re-Login to the SIU: Setting ly logfile th 3, file lu theo quy tc SIU_HCxxxx_after_upgrade.log

OSmon> getswsessionstatus 1 ActivationCompleted ====> SIU Software upgrade was successful OperationSucceeded

OSmon> endswsession 1 OperationSucceeded

Check the software revision and verify that the primary software is the latest version and the SIU is running on the primary application as follows:

OSmon> rev ------------------- OSE modules ------------------------------------------ oam.chk Operation & Maintenance R2J01 secmgrr.chk Security Manager R2G02 inetr.chk MLPPP Daemon R2D03 ltp.chk Local Terminal Port R2D03 snc.chk Synchronization R2H02 pd.chk Packet Distributor R1L_1 cesopsn_pwr.chk Circuit Emulation Service R1F03 hdlc_pwr.chk HDLC Pseudo-Wire Emulation R1H07 p_relayr.chk Packet Relay R2H01 profiler.chk System Profiler R1L_1 hwtest.chk Hardware Tester P2A01 lcf_cp.chk Local Connectivity Function R1C01 bsp.drv Board Support Package R2H02 bootstrap.chk Bootstrap R2G02 loader.drv Software Loader R1L_1 linuxload.drv Linux Loader R2H02 ------------------- Firmware modules ------------------------------------- PBOOT CXC 112 3777/1 R1G02 ------------------- Software archives ------------------------------------ Primary: OSE CXP102138_1 R2AB05 Linux - R2AB05 Backup: OSE CXP102084_1 R3F01 ------------------- Active software -------------------------------------- OSE Primary Linux Primary

Make sure the primary is activated software T12B.

INSTRUCTION



2014-07-25 A

9.

Restore SIU configuration xml file. (Configuration xml file has just gotten from step of item 2 above) Make sure your SFTP server is running. The SIU configuration file must be in XML format.

OSmon> uselocalsftp on

OSmon> startsession bcm1 OperationSucceeded

OSmon> download bcm1 sftp://siu:[email protected]/SIU/SIU_HCxxx.xml OperationSucceeded

OSmon> getsessionstatus bcm1 DownloadCompleted OperationSucceeded

When the file download is complete, activate the configuration using the following command:

Osmon> restore bcm1 admin OperationSucceeded

The SIU will restart and connectivity will be lost

10.

Re-Login to the SIU and enter the following commands:

Setting ly logfile th 4, file lu theo quy tc SIU_HCxxxx_ready.log

OSmon> getsessionstatus bcm1 ActivationCompleted OperationSucceeded

OSmon> endsession bcm1 OperationSucceeded

Note: If any errors are encountered while loading the script, contact Ericsson support.

11.

OSmon> getalarmlist

OSmon> getmoattribute stn=0

OSmon> getmoattribute stn=0,equipment=0

OSmon> getmoattribute

INSTRUCTION



2014-07-25 A

12.

Check SIU LED indicators are normal

Refer to figure in step 1 to locate the LED indicators in the SIU.

Indicator Status

Fault Off

Power On

Opera. On

Sync On

Info. Off

If the Fault or Info. LED is lit, troubleshoot and clear the fault.

Make sure, all ports and parameters on new SIU are defined correct as existing SIU.

4 SWAP SIU HARDWARE

1.

- Make sure, new SIU finished restoration configuration & working status is ready.

- Must be making labels on all cables connected to ports of existing SIU. ===> very very important.

2.

- After, anything is ready. ASP will call for E/// guys confirm starting time swap SIU. When accepted by E///. ASP will turn off power existing SIU & replace new SIU.

- Make sure, all cable are reconnected correction as before swap.

- Check physical links are up. - And then, ASP need contact with E/// guys as soon as possible.

INSTRUCTION



2014-07-25 A

3.

Log-in to new SIU after replaced and enter the following commands:

Setting ly logfile th 5, file lu theo quy tc SIU_HCxxxx_new.log

Check alarms in the SIU OSmon> getalarmlist

Troubleshoot and clear any alarms.

Note:

- Make sure after swap, all alarms are the same as before swap on the both SIU/Node B/RBS 2G.

4.

Ping to OSS OSmon> ping 10.149.27.67 PING (10.26.2.65) 56(84) bytes of data. 64 bytes from 10.26.2.65: icmp_seq=0 ttl=255 time=1.824 ms 64 bytes from 10.26.2.65: icmp_seq=1 ttl=255 time=1.702 ms 64 bytes from 10.26.2.65: icmp_seq=2 ttl=255 time=1.681 ms 64 bytes from 10.26.2.65: icmp_seq=3 ttl=255 time=1.706 ms 64 bytes from 10.26.2.65: icmp_seq=4 ttl=255 time=1.715 ms --- 10.26.2.65 ping statistics --- 5 packets transmitted, 5 received, 0.0% packet loss round-trip min/avg/max = 1.000/1.725/1.823 ms

===> To stop ping result, use CRT+C

If the ping is not successful, then troubleshoot.

Note: Make sure ping to OSS ok.

5.

Enter the following commands to print the SIU configuration: OSmon> getmoattribute stn=0 OSmon> getmoattribute stn=0,equipment=0 OSmon> getmoattribute

OSmon> log read All 5 logfiles will keep on your laptop and send to Ericsson for audit (or VNP requirement later on).

6 Waiting confirm from OMC/Eric before leave the site.

Documents

MOP SIU Replacement_VNP2 _RevD.pdf