Upload
leslie-aubert
View
217
Download
2
Tags:
Embed Size (px)
Citation preview
Module 6
Processing the specimens and inoculation on
solid and liquid media
1
Learning objectives
At the end of this module you will be able to: work properly within a BSC; process specimens from sterile and non sterile sites,
according to protocols, for TB culture; homogenize and decontaminate respiratory specimens
by: – Petroff modified method,– NALC-NaOH method;
inoculate cultures (solid and/or liquid media); incubate inoculated media under proper conditions.
2
Content outline
• Working within a BSC • Homogenization and decontamination
procedures:– sodium hydroxide (modified Petroff)– N-acetyl-L-cysteine-sodium hydroxide (NALC)
• Alternative protocols for processing different specimens
• Culture tube inoculation• Culture tube incubation• Quality assurance
3
Work in a BSC (1)
• Prepare a written checklist of materials needed.• Place absorbent paper towelling on the work
surface.• DO NOT block the grille.• Perform all operations at least 10 cm (4 inches)
from the front grille on the work surface.• Place all materials and aerosol-generating
equipment away from the front grille.
4
Example of a written checklist
• Pipettes (n)• Centrifuge tubes (n)• Media (n)• Loops (n)• Distilled water (ml)• Decontaminating solution (ml)• Slides (n)
Centrifuge tubes and culture tubes should be clearly labelled in order to avoid mismatching of patients.
5
Work in a BSC (2)
• Pipette-discard containers should contain an appropriate disinfectant.
• Do not keep several tubes or bottles open at the same time.
• Do not keep a sterile reagent open while processing specimens.
• All infectious material must be discarded in an autoclave bag. The bag is transported to the autoclave at the end of work.
6
Work in a BSC –practices to be avoided
• Do not tape autoclavable disposal bags to the outside of the cabinet .
• Do not keep the flame of the Bunsen burner continuously alight during operations in the BSC.
7
Work in a BSC (3)Acceptable Unacceptable
Avoid overcrowding the work surface of the BSC. 8
Homogenization and decontamination
9
Homogenization anddecontamination – why?
• To free the bacilli from the mucus, cells or tissue in which they may be embedded.
• Most clinical specimens, especially sputum, are contaminated,
• Organisms of the normal flora would rapidly multiply in the culture medium before the tubercle bacilli started to grow.
• To concentrate TB bacilli from specimens.
10
Remember…
• Process only one specimen at a time.• Do not keep several containers or centrifuge
tubes open at the same time in the BSC.• Use aliquots of decontamination solutions (1 vial
of decontaminant per specimen).• Use a fresh pipette at every step to avoid transfer
of bacilli from one specimen to another.
11
Specimens for TB culture
Contaminated clinical specimens:
– sputum– urine – other specimens from
sites contaminated by normal flora
Specimens from sterile sites:
– bone marrow– body fluids– biopsies, tissues and
surgical specimens– cerebrospinal fluid.
DECONTAMINATION
12
CautionDigesting/decontaminating agents are toxic to tubercle bacilli to some extent. Therefore:•Follow digestion/decontamination procedure precisely.•Acceptable contamination rate (solid) = 3–5%• Acceptable contamination rate (liquid) = 5–10%
Contamination rates lower than those listed above may indicate too harsh a decontamination procedure ‒ with the possible consequence of false-negative cultures.
13
Sputum specimens1. To minimize the risk of cross-contamination, do not open more than
one tube at a time.
2. Carefully label all the tubes before starting to process the samples.
3. Work in batches corresponding to one centrifuge load (e.g. 8 specimens at a time).
4. Always digest/decontaminate the whole specimen.
5. Pour out the specimen gently from the container into the centrifuge tube, to avoid spilling.
6. Never transfer the sample before labelling the tube.
Digestion and decontamination procedures
– good practice
If possible, digest/decontaminate the sample in the same container as was used for collection.
14
Other specimens – gastric lavage
Specimens obtained by gastric lavage should be processed within 4 hours of collection. MIND that collection has to be performed in a tube containing 100 mg of sodium bicarbonate
Procedure:•Centrifuge the total volume at 3000g for 15 minutes.•Discard the supernatant and resuspend the sediment in 5 ml sterile distilled water.•Add an equal volume of NALC‒NaOH and proceed as for sputum.•Inoculate the sediment immediately onto culture medium.
15
Other specimens – urine
• Do not pool the specimens.• Centrifuge the total volume at 3000g for
15 minutes.• Discard the supernatant fluid .• Proceed as for gastric lavage.
16
Other specimens – tissue
• Lymph nodes, biopsies, clots and other surgically resected tissue should be cut into small pieces with a sterile scalpel or scissors.
• Homogenize the specimen in a sterile porcelain mortar or preferably in a small non-reusable tissue grinder, using 2–5 ml sterile saline.
• Inoculate the suspension onto culture media.
17
Other specimensMucopurulent materials• Handle as for sputum when volume is 10 ml or less.• Handle as for mucoid gastric lavage when volume is
more than 10 ml.
Fluid materials• If collected aseptically, centrifuge and inoculate
sediment directly onto culture medium (preferably liquid medium).
• If not aseptically collected:– handle as for sputum when volume is 10 ml or less;– handle as for gastric lavage fluid when volume
exceeds 10 ml.• To maximize the recovery rate, the entire volume of CSF or
other aseptically collected fluid should be cultured (preferably in liquid medium). 18
Other specimens
Sterile, no decontamination:
– spinal, synovial or other internal body fluids;– bone marrow;– pus from cold abscesses;– surgically resected specimens (excluding
autopsy material);– material obtained from pleura, liver and
lymph nodes as well as biopsies (if not connected to potentially contaminated regions).
19
SputumPetroff
NALC
Solid, Ogawa
Liquid
Other specimens
Centrifuge and inoculate
NO decontaminationSterile
Non sterile Centrifuge if necessary, then Petroff or NALC
Processing chart
If preservative added
Kudoh
Solid, LJ
20
Main processing methods for sputum
• Sodium hydroxide (modified Petroff) method.
• Simple culture method (modified Kudoh)• N-Acetyl-L-cysteine-sodium hydroxide
(NALC‒NaOH) method.
21
Sodium hydroxide (modified Petroff) method – advantages
• Simple.• Inexpensive reagents, easy to obtain.• Effective control of contaminants.• One hour.• Sterilized NaOH solution can be kept for
several weeks.
22
• Specimen exposure times must be strictly followed.
• The procedure kills up to 60% of tubercle bacilli in clinical specimens.
• Not suitable for liquid media.
Sodium hydroxide (modified Petroff) method – disadvantages
23
Sodium hydroxide (modified Petroff) method – procedure
ADD X ml 4% NaOH
1. To x ml of sputum, add x ml of 4% NaOH.
2. Tighten cap of container and shake to digest.
3. Let stand for 15 min at room temperature (20–25 ºC).
4. Fill the tube to within 2 cm of the top with phosphate buffer.
5. Centrifuge at 3000g for 15 minutes.
6. Carefully pour off the supernatant into a discard can containing an appropriate disinfectant and resuspend the pellet
7. Using a pipette (not a loop), inoculate deposit onto two slopes of LJ medium (and one of LJ with pyruvate – optional); inoculate each slope with 0.2 ml
8. Prepare the slides for smear microscopy and store the sediment at 4 ºC or −20 ºC. 24
1. Kills only about 30% of tubercle bacilli, allowing more positive cultures than other methods.
2. Time required to perform the procedure: single-specimen processing takes approximately 40 minutes; processing 20 specimens would take approximately 60 minutes.
3. Suitable for liquid media.
NALC‒NaOH method – advantages
25
1. Acetyl-cysteine loses activity: it needs to be made fresh daily.
2. Ready-to-use NALC-NAOH solutions are commercially available, but at higher cost
NALC‒NaOH method – disadvantages
26
NALC‒NaOH method – procedure
Xml NALC-NaOHADD X ml NALC-NaOH
1. To x ml of sputum, add x ml of NALC-NaOH.
2. Tighten cap of container and shake to digest.
3. Let stand for 15 minutes at room temperature, with occasional shaking.
4. Add sterile distilled water or phosphate buffer to make up to approx. 50 ml.
5. Centrifuge at 3000g for 15 minutes.
6. Decant the supernatant and resuspend the sediment.
7. Inoculate 0.2 ml onto culture medium (liquid or solid).
27
Trisodium phosphate method – procedure
Xml trisodium phosphate solution
ADD X ml Trisodium phosphate
1. To x ml of sample, add x ml of trisodium phosphate solution.
2. Tighten cap of container and shake to digest.
3. Let stand for 12–18 hours at room temperature.
4. Fill the tube to within 2 cm of the top with sterile water (e.g. the 50-ml mark on the tube) and vortex-mix.
5. Centrifuge at 3000g for 15 minutes.
6. Discard the supernatant.
7. Inoculate 0.2 ml onto solid culture medium.
28
Simple culture method (modified Kudoh)
To x ml of sputum add x ml of 4% NaOH
Tighten cap of container and shake to digest for 20 seconds
X ml 4% NaOH
Let stand for 15 minutes at room temperature
Inoculate deposit on to two slopes of acid Ogawa mediumUse a pipette (not a loop), inoculate each slope with 0.1ml
ADD X ml 4% NaOH
29
Simple culture method (modified Kudoh)
AdvantagesBecause the method does not require centrifugation, it- minimizes the manipulation of the samples, - reduces the execution time of the culture compared to the Petroff method - facilitates the qualification of professionals involved in culture of TB bacilli
DisadvantagesReduced sensitivity compared to the centrifugation methods
30
1% CPC–2% NaCl method – procedure
Xml 1%CPC containing specimen
ADD X ml 1% CPC
1. To x ml of sputum, add x ml of 1% CPC and 2% NaCl. Transport to a processing laboratory.
2. Allow liquefaction (48–72 hours).
3. Fill the tube to within 2 cm of the top with sterile distilled water (to reduce viscosity).
4. Tighten cap and mix well.
5. Centrifuge at 3000g for 15 minutes.
6. Discard the supernatant.
7. Resuspend the sediment in the remaining sterile distilled water.
8. Inoculate 0.2 ml onto solid culture medium.
31
Remember!
Store the remaining sediment refrigerated or frozen in a 1.5–2-ml sterile screw-cap vial, properly labelled.
It may be used later on as a back-up specimen, in case of contamination or culture failure for any reason.
32
Inoculation and incubation
33
Inoculation – solid media
• Use sterile Pasteur pipettes and carefully inoculate a volume of 0.1–0.2 ml of sediment.
• Two tubes should be inoculated from each sample.
• LJ with pyruvate and no glycerol could be added in settings in which M. bovis is frequently isolated.
• Prepare the slides for smear microscopy and store the sediment at 4 ºC or −20 ºC.
34
Inoculation – liquid media• Remember : liquid media need to be
supplemented before inoculation.
• Inoculate 0.5–1 ml of sediment into the tube using a disposable pipette.
• Tighten the caps.
• Mix by inversion.
Use aseptic techniques!
35
Inoculation of liquid culture media – key points
• Minimize the production of aerosols:– open the caps of liquid media slowly;– avoid vigorous shaking of the specimen;– do not expel the last drop from the pipette.
• Use aseptic techniques and sterile material to avoid contamination.
• Inoculate liquid media first to reduce the chances of carry-over of any contaminants.
• Prepare smears for staining after all media have been inoculated.
• Inoculate the media with clinical specimens as soon as possible. 36
Inoculation work-flow
1. Liquid media
2. Solid media
3. Smear
37
Incubation
• Place inoculated cultures in the incubator as soon as possible.
• Incubator temperature should be 35–37 ºC.
• Monitor the incubator temperature regularly.
• Solid media:
– Keep the caps loose for the first 48 hours of incubation to let the inoculum to dry
– tighten culture caps of solid media after 48 hours of culture to avoid dehydration of the medium;
– incubate solid cultures in slanted position for at least 1 week;– incubate for 8 weeks before reporting a culture as negative.
• Liquid media:
– incubate for up to 6 weeks before reporting a culture as negative.
38
True and false exercise
1. M. tuberculosis is never affected by the decontamination protocol.
2. Performing decontamination in the collection container may reduce the risk of errors in the laboratory.
39
Module review: take-home messages
Process clinical specimens as soon as possible. Correct labelling of tubes avoids the “patient/culture
mismatch”. Different decontamination protocols apply to different
samples. Too small an inoculum can lead to a false-negative
result. Aseptic technique is important to avoid contamination. Prepare smears for staining from the processed
sediments after all media have been inoculated.40
Self-assessment
• What are the advantages and disadvantages
of the Petroff/NALC digestion and decontamination procedures?
• What safety and procedural precautions should be taken while processing specimens?
• Describe the most important steps of the decontamination process.
41