Trade of Plumbing – Phase 2Module 1 – Unit 3

Module 1: Thermal Process and Mild Steel Pipework

Unit 3: Workshop Related SafetyDuration – 7 Hours

Trade of Plumbing – Phase 2Module 1 – Unit 3

In this module we learn how to:

State the risks, hazards and causes of accidents in the workshop.Demonstrate correct use of power tools.Demonstrate safe use of grinding tools and pedestal drills.

Trade of Plumbing – Phase 2Module 1 – Unit 3

• Key Learning Points

Rk H Risks, hazards and causes of accidents in the workshop. Rk Cleanliness and tidiness in the workshop. P Good working practice. Rk Sk Use and care of hand tools. Rk Sk Use and care of grinding tools, pedestal drills. Rk Personal protection equipment. Rk Safety signs.

Trade of Plumbing – Phase 2Module 1 – Unit 3

Safety SignsMany signs are used on a construction site and their meanings need to be considered and understood. Signs are not meant for show but are placed there for a reason. The classification of a sign will fall into one of the following categories:

Information - square or rectangular, white on green background.Warning - triangular, black on yellow background.Mandatory - circular, white on blue background.Prohibition - circular, red border and cross bar on white background.

Trade of Plumbing – Phase 2Module 1 – Unit 3

Safety Signs

Trade of Plumbing – Phase 2Module 1 – Unit 3

Fire Prevention Make suitable provisions to deal with an outbreak of fire. Always check that nothing is left smouldering on completion of the

work. Gas and electrical supplies should be turned off as quickly as

possible and combustible materials moved out of reach of the fire. Should a fire break out, it is essential to use the correct equipment to

control its spread. Using the wrong type of extinguishing agent can make things worse.

Trade of Plumbing – Phase 2Module 1 – Unit 3

Fire Extinguisher Selection Chart

Type of fire Water Foam CO2 BCF* Powder Fire blanket

Wood, paper and textiles etc.

Yes Yes No Yes No Yes

Flammable liquids, oils and paints etc.

No Yes Yes Yes Yes Yes

Electrical equipment No No Yes Yes Yes No

Extinguisher colour Red Cream Black Green Blue Red

*Bromochlorodifluoromethane

Trade of Plumbing – Phase 2Module 1 – Unit 3

Fire Extinguisher Examples

Trade of Plumbing – Phase 2Module 1 – Unit 3

Safety in the Workshop

The vast majority of safe working practices are common sense. For example, do not lift extremely heavy loads, and, when lifting, approach the load squarely and lift keeping a straight back, using the legs, not the back, and keeping the load close to the body. When lowering the load, simply reverse the process. Many people today suffer with bad backs due to foolish acts when they were younger.

Trade of Plumbing – Phase 2Module 1 – Unit 3

Hand ToolsHand tools should always be maintained in a safe condition and only used for their intended purpose.

Trade of Plumbing – Phase 2Module 1 – Unit 3

Ladder WorkWhen using ladders, check them over to see that they are in good condition and secure them to the stiles (not the rungs) while in use. Stand them on a firm, even base and always use them at the correct angle of approximately 750 (ratio:4 up to 1 out); above all, never over-reach when working at high levels.

Trade of Plumbing – Phase 2Module 1 – Unit 3

Working on PlatformsTake particular care when working from a platform such as that provided by scaffolding; always consider those below. The scaffold should be erected only by certified operatives, and should it be checked weekly or after adverse weather conditions: thus it's condition should be sound, but always have a visual inspection to identify obvious defects. Above all, never alter or work from ineffective scaffolding platforms. Defects to look for include:

Missing components, e.g. toe boards or guard rails.Poor assembly, e.g. loose, overlapping or protruding boards.Damaged scaffolding, e.g. split boards and bent or rusty poles.Unstable scaffolding, e.g. no bracing, no tie-ins and no base plates.Obstructed or overloaded scaffolding.

Trade of Plumbing – Phase 2Module 1 – Unit 3

Protective Clothing and EquipmentOveralls and safety footwear may be provided by the employer, or you may have to buy these items yourself. Employers have a legal duty to provide all other protective equipment free of charge and the employee must use it correctly and report any defect to damage. Visitors to the site or other workers are also entitled to the same protection.

Head Protection

The law requires the use of suitable head protection on all building sites unless there is no risk of head injury other than the person falling. Safety hats should be adjusted to fit correctly; your failure to make the correct adjustment may mean that you are not providing the necessary level of safety.

Eye Protection

Safety glasses, goggles or eye shields must be worn where there is any foreseeable risk of eye injury. Eye injury can result from:The use of power tools - drilling, grinding and threading.Hammering and driving tools - cutting, chipping and chiselling.Flying particles - dust and chemical splashes.Welding processes - sparks and molten splashes.Glare from light - electric arc welding.

Trade of Plumbing – Phase 2Module 1 – Unit 3