Model: Product Name: Product Code: SR2 · Dimensions 300 x 200 x 85mm Weight 1.2kg ... ISI sa-nv - Instrumentation for Science and Industry ... main system administrator Network Server

The sr-2 is the second generation of the Hanwell Smart Receiver. Itis a network enabled receiver, designed for collectingenvironmental monitoring data from multiple points within a site,or across multiple sites. In addition, it can be upgraded to atransceiver which both receives and retransmits the data. It usesstandard TCP/IP communications protocols for speedy datahandling. The network traffic generated is very low and data isautomatically sorted and filed.

This multipoint operation can be further expanded, with the use ofoptional GPRS, and used on a larger national or internationalbasis. See the diagram overleaf for some potential ways of usingthe sr-2, or contact Hanwell to discuss your site specificrequirements.

In addition to receiving data from the rl-2000, rl-4000, rl-5000 andrl-8000 ranges of sensors, the unit can also read hard-wiredsensors and, optionally, be fitted with up to eight on-boardprobes. Each sr-2 can handle data from up to 253 sensors, and upto 16 sr-2s can be run on a single system bringing it to a total of4048 sensors. The sr-2 supports Hanwell’s standard and extendedtransmission data formats.

The sr-2 logs all received data in its on-board 512kb memory. TheRadiolog software continually interrogates the sr-2 for the most

recent data, and downloads the data according to user-definedlogging periods to the server or operating PC. Software users canview live and historic data, produce out of spec and summary reportsand set alarms on both the data levels and the rate of change.

In addition to the data readings from the sensors, the sr-2 can logthe corresponding Received Radio Signal Indicators (RSSI) whichreveal the strength of radio reception of each Sensor. As well asbeing logged, the RSSI is indicated on the front LCD along withother status information. An optional remote Receiver can beconnected to improve radio reception in difficult areas.

The sr-2 is designed to be in constant communication with thesoftware but has user-configurable fallback behaviour in the eventof network or power failure. An on-board battery provides a UPSwith 2.3A/hour life to carry it through up to 12 hours’ powerdisruption (larger external UPSs are available as an optionalextra).

Alarm relays are included: these can indicate that the readings areout of specification, and can be optionally set to indicate anetwork failure. A MS BUS connection allows the sr-2 to drive theHanwell MS1000 environmental control system.

Model:

Industrial ApplicationsProduct Name:

Product Code:SR2

Smart Receiver (Mk2)

See diagram overleaf

RoHS Compliant

Transmitter 1Not available in US, 2US only

Dimensions 300 x 200 x 85mm

Weight 1.2kg

Power Supply Options 110V AC or 240V AC. On-board 12V battery back-up supplying 2.3A/hr

Case Material(s) Powder coated mild steel

Operating Humidity Range 10…90% RH, non-condensing

Operating Temperature Range 5…40C (Temperature compensated range)

Radio Specification

FF1 F11 SF1 HP2

Radio Frequency 434.075 MHz 433.920MHz 433.875 to 434.650MHz in 25 KHz increments Synthesized

Radio Power 10mW 10mW 10mW Programmable

Radio Range 2 miles over open ground

Outputs

Alarm Outputs 1 x nominal 12V, 2 x changeover relays (energised when no alarms exist)

MSBUS 4 core signal cable

Accessories (e.g. mounting brackets, remote probe etc)

Codes Description

RX-xx Remote receiver – please specify the frequency required

Y306-05-03 Thermistor probe on 5m cable with bare ends suitable for wiring into the sr-2’s on-board probe inputs

Y404-05-03 Humidity probe on 5m cable with bare ends, as above.

Y405-05-03 Combined thermistor & RH probe on 5m cable with bare ends, as above

ABR12/24 Alarm beacon, red strobe, 12/24V with bracket and 2m cable

SR2-E-7.0-UPS 7.0Ah external wall mounted UPS

SR2-E-15-UPS 15Ah external wall mounted UPS

Instrumentation for Science and Industry ISI sa-nv Rue du Doyenné 3 Dekenijstraat 1180 Brussels Tel +32 (0) 2 343 30 81 web : http:// www.isi-be.com mail : [email protected]

New from Hanwell is the rl5000 dpradiotelemetry transmitter, designed foruse withthe Radiolog 8 environmentalmonitoringsystem. The units are inIP65-rated cases andare suitable for usein tough environments.

Utilising an integral temperaturecompensated pressure sensor therl5000 differential pressure transmitterdelivers exceptional performance. Thesensor utilises a silicon, micromachined, stress concentrationenhanced structure to provide a verylinear output to the measured pressure.The ports are designed with matcheddead volumes. This series is intendedfor use with non-corrosive, nonionicworking fluids such as clean dry air, drygases and the like.

The media wetted materials are thesilicon diaphragm, glass filled nylon,RTV and alumina ceramic. Thetransmitter ID, transmission speed andcalibration data is programmed into itsonboard memory using Radiolog 8, asoftware package which automaticallyrecognises the type of unit connected tothe PC via the USB lead.

Fitted with a custom-designed LCD toindicate current readings, battery liferemaining and alarm conditions. Thereis an instantaneous display updatebutton located on the front panel.Pressure connections are made viaquick release Lemo pressureconnectors, which avoid damage to the

pressure sensor when disconnecting forcalibration.

The transmitter is typically powered bya 7.5V 2700mAh battery or 2 x LithiumC size 5 Ah that can be fitted by the user . The battery life will be dependant on thetransmission speed. Larger batterypacks are available, local power input isalso an option. An indicator on the LCDwill warn when the battery is low, andthe transmitter maintains a record ofwhen the battery has been changed.The rl-5000 range has been designed tocomply with the RoHS and WEEE EUdirectives, and carries the CE mark.

Product Code RL5001-xxx Series rl5000

1 Not available in US2 Only available in US

Typical Applications° Environmental monitoring° Warehouse monitoring° Pharmaceutical monitoring° Laboratory monitoring° Building monitoring & control° Event logging°T emporary monitoring

InstrumentDimensions: 197 x 106 x 60mmWeight: 300 gramsCase Material: ABSPower Supply: 7.5V 2700mAh or 2 x Lithium C sizeOp. Humidity Range: 0…95% RH, non-condensingOp. Temp. Range: -20 °C to +60 °C

SensorsCode DescriptionRL5001 Thermistor, PT100, Humidity, Linear

Radio*Radio Frequency: Fixed frequency modules

434.075 MHz1433.920 MHzSynthesised modules433.875 to 434.650 MHzin 25KHz increments1

458.650 MHz 2

Radio power: 10 mWRadio range: 3 km over open ground

Communications & SoftwarePC/Logger Interface: Standard USB A/ USB mini-BPC Software: 32bit Windows with

Radiolog 8.3 or laterMinimum O/S: Windows 2000, Windows XP,

Windows NT

AccessoriesCodeY055 USB communications leadW250 USB configuration tool

(required for users with Radiologsoftware earlier than 8.3)

rl5001 radio transmitter

Radiologger - Transmitter

ISI sa-nv - Instrumentation for Science and Industry (INTERCONTINENTAL SERVICES INC)Rue du Doyenné 3 Dekenijstraat 1180 Brussels – Belgium - Tel 02/ 343 30 81 Fax 343 12 05 mail : [email protected] web : www.isi-be.com

Model:

Industrial ApplicationsProduct Name:

Product Code:SR2

Smart Receiver (Mk2)

Network UserFor example, ahome worker

Network UserFor example,someone needingweekly reports

Network UserFor example,main systemadministrator

Network ServerCollects data fromall sr-2’s and isinterrogared byNetwork Users

Isolate mains supply before removing this cover. Live parts enclosed.



Local SiteOne or more sr-2’son a main siteconnected via LANpoints

Remote SitesOne or more sr-2’sfrom remote sitesvia LAN or WAN, forexample, off-site

Remote SitesNon-networkedsite connectedvia modem

LAN

LAN

or WAN

Modem

Interface

One system can comprise up to 16 separatesites but all data is treated the same way.


The rl4001 & rl4002 are precisionthermistor temperature measuring andradio transmission devices. The rl4001has a single channel the rl4002 is dualchannel. The sensors are connectedvia 2 pin Lemo plugs and sockets.They allow wire-free monitoring of asite, with real time alarm notificationand historical analysis of data. Each4000 unit reads its on-board sensorsproviding accurate and reliableinformation about environmentalconditions. This data is transmitted, atuser-defined intervals, to the Radiologsystem where it is filed for analysis.

rl4000 series transmitters can be usedin accordance with GAMP and FDAregulations. The transmitters andsensors can be calibrated by the eitheruser or Hanwell staff on-site or atHanwell’s in-house calibrationlaboratory.

Transmitter ID number andtransmission rate are set in thetransmitter using a simple softwareprogram (free to download) and a USBcable. Each unit has an LCD screensimultaneously displaying the mostrecent readings taken and the predictedbattery life.The transmitter is poweredby a single 3.6V AA Lithium battery,which can be fitted by the user.

The battery life will be dependent onthe transmission rate set. An indicatoron the LCD will warn when the batteryis low, and the transmitter maintains a

record of when the battery was lastchanged.

Each 4000 series radio transmitter hasenough internal memory to store up to100000 readings and is in factcontinually logging guaranteeing 100%validity of the data. The 4000 series unitcan be downloaded via the high speedUSB connection directly into the PCsoftware (V8.4 or later only). The datalogged will be added to the radio data,providing a continuous history for thattransmitter.

The moulded case allows easy accessto the battery and USB socket, as wellas having slots to fit onto secure wallbrackets.

CFR21 part 11 compliant software isavailable. OQ & IQ templates areincluded, full on-site validation servicesare available.

The 4000 range has been designed tocomply with the RoHS and WEEE EUdirectives, and carries the CE mark.

Product Code RL4001-434.075* & RL4002-434.075*

Series rl4000

Typical ApplicationsMonitoring in: ° Fridge/Freezer monitoring° Laboratories° Hospitals° Pharmaceutical° Warehousing

InstrumentDimensions: 110 x 80 x 35mmWeight: 200 gramsPower Supply: 3.6 Volt AA Lithium batteryBattery Life: 18 monthsCase Materials: ABS & PCOperatingHumidity Range: 0…100% non-condensingOperating Temp Range: -20° to +60° CMemory Capacity: 100000 readings

Sensors TemperatureSensor: Precision thermistorRange: -40° to +70° CAccuracy: +/- 0.1° C between

-25° C to +50° C +/-0.3 elsewhereResolution: 0.1° C

Radio*Radio Frequency: 434.075MHz

433.920MHz (fixed)433.875 - 434.650MHz in 25KHz increments(synthesised)

Radio Power: 10 mWRadio Range: 3 km over open ground

AccessoriesCode:

Y119 Wall mounting security bracketY055 Setup communications cableG129 Replacement 3.6V Lithium AA

batteryCAL-T 3 point calibration between

-20 and +110C (single Ch)CAL-T-LOW 3 point calibration between

-90 and +110C (single Ch)CAL-T-2 3 point calibration between

-20 and +110C (dual Ch)CAL-T-LOW-2 3 point calibration between

-90 and +110C (dual Ch)

Single channel thermistor


Above:Detail of USB socket

Below:Optional wall mountingsecurity bracket


The rl4106 radio transmitter is one of anew range of advanced temperatureand humidity radio transmitters. Theyallow wire-free monitoring of a site,with real time alarm notification andhistorical analysis of data. Each rl4106unit reads its on-board sensors toprovide accurate and reliableinformation about environmentalconditions. This data is transmitted, atuser-defined intervals, to the Radiologfor Museums system where it is filedfor analysis.

The rl4106 has two sensors as standard:a precision temperature probe and ahigh quality humidity probe. Thesesensors can be mounted internally tothe transmitter body, externally on thecase or remotely on a probe. Anadditional surface temperature probecan be added to check the dewpointmargins. These sensors can becalibrated by the users or at Hanwell’sin-house calibration laboratory.

The ID number and transmission rateare set in the rl4106 using a simplesoftware program (free to download)and a USB cable. Each unit has an LCDscreen simultaneously displaying themost recent readings taken and thepredicted battery life.

The rl4106 is powered by a single 3.6VAA Lithium battery, which can be fittedby the user. The battery life will bedependent on the transmission rate set.An indicator on the LCD will warn when

the battery is low, and the rl4106maintains a record of when the batterywas last changed.

The moulded case allows easy accessto the battery and USB socket, as wellas having slots to fit onto secure wallbrackets and a plain front panel to hidethe LCD if more discreet monitoring ofpublic areas is desired.

The rl4000 range has been designed tocomply with the RoHS and WEEE EUdirectives, and carries the CE mark.

Product Code RL4106Series rl4000

Typical ApplicationsMonitoring in: ° Hospitals° Pharmaceutical° Warehousing

InstrumentDimensions: 110 x 80 x 35mmWeight: 200 gramsPower Supply: 3.6 Volt AA Lithium batteryBattery Life: 18 monthsCase Materials: ABS & PCOperatingHumidity Range: 0 to 100% non-condensingOperating Temp Range: -15° to +65° CMemory Capacity: 100000 readings

Sensors TemperatureSensor: Precision thermistorRange: -15° to +65° CAccuracy: +/- 0.2° C between

-15° C to +65° CResolution: 0.1° C

HumiditySensor: Capacitive polymerRange: 0 to 100% non-condensingAccuracy: +/- 0.2° C Resolution: 0.1° C

Radio*Radio Frequency: 434.075MHz

433.920MHz (fixed)433.875 - 434.650MHz in 25KHz increments(synthesised)

Radio Power: 10 mWRadio Range: 3 km over open ground

AccessoriesCode:

Y119 Wall mounting security bracketY055 Setup communications cableG129 Replacement 3.6V Lithium AA

battery

Temperature & humidity


Above:Detail of USB socket

Below:Optional wall mountingsecurity bracket

ISI sa-nv - Instrumentation for Science and Industry (INTERCONTINENTAL SERVICES INC)Rue du Doyenné 3 Dekenijstraat 1180 Brussels – Belgium - Tel 02/ 343 30 81 Fax 343 12 05 mail : [email protected] web : www.isi-be.com

Instrumentation for Science and IndustryInstrumentation for Science and IndustryInstrumentation for Science and IndustryInstrumentation for Science and Industry ISI sa-nv Rue du Doyenné 3 - 1180 Brussels Tel +32 (0) 2 343 30 81 Fax 02/ 343 12 05 web : http:// www.isi-be.com mail : [email protected]

Technical SummaryInstrumentDimensions: 100 x 100 x 60 mm

Weight: 600g

Power Supply: User replaceable 2 x alkaline ‘D’ cell Battery pack.

Battery Life: Up to five years (Based on one message a day i.e.

30 minute pulse count and no events enabled)

Case Material: ABS & PC

N.B Instrument operating range -20oe -20e -20 C to 60oo 60o 60 C in a

non-condensing RH environment

GPRS – Quad band moduleNetwork Compatibility: Quad band, band user selectable

(Quad Band) Aerial Connection: SMA socket

Aerial Type: Stubby straight/right angle + optional remote mount on 2mtrs cable

iSense GPRS TransmitteriS

EN

SE

G

PR

S T

RA

NS

MIT

TE

R

Features:

Completely self contained (battery operated)

Date and time stamped monitoring

Up to five year battery life

Transmit rate increase on event

Remote setup options

Data stored in non volatile memory

All data recovered in the event of temporary GPRS coverage problems

Easy to understand journey profile information

Works with a range of sensor families

Evolved from Hanwells existing range of established

radio logging products the iSense is an innovative

self contained unit enabling remote monitoring of

diverse parameters via wireless GPRS technology.

Locations that previously seemed inaccessible

including, buildings, machinery, infrastructure or

vehicles can now easily be accessed and monitored.

A number of different sensors can be attached to

the iSense in order to monitor parameters such as

energy, temperature, pressure, structural stress and

many more.

This real-time information is then transmitted via

GPRS to a central database, and can be accessed

immediately on a PC for viewing, recording and

assessment.

Product benefitsGPRS technology

Non-Intrusive design

Easy installation

A wide range of monitoring

parameters available

Individual configuration options

Easy reading management system

Comprehensive analysis and

data history

Up to five year battery life


Server

SR2 User PC

GPRS – IP Addresssecure access via DMZ

(demilitarised zone)

Network

Application: Oil tankPressure and level

Application: HospitalFridges and freezer monitoring

Application: TruckTemperature

Application: BridgeShock and vib ration

Application: SchoolEnergy monitoring

hanwell.com

iSense communication to your local PC is easy

using GPRS technology

Typical applications

Bridge stress and vibration monitoring

Schools energy monitoring

Hospitals and hospital food

transportation monitoring

Fridge temperature monitoring

Civil engineering

Laboratory monitoring

Chemical transportation


iS

EN

SE

G

PR

S T

RA

NS

MIT

TE

R

Easy installation of software

Clear set up capabilities

Easily integrated into existing Hanwell

monitoring system

Uncomplicated set-up capabilities

Immediate access to graphical data

Date and time specific

Clear visual and statistical evidence of iSense environmental conditions

Straightforward data retrieval

These screen shots show typical results for an

iSense transmitting data for temperature and

humidity (above) and energy (right).

The screen shot opposite is an example of the set-up capabilities

available to the user.


The part numbers for the iSense product range are constructed in four parts as follows:

Where

C1 = code for sensor on channel 1

C2 = code for sensor on channel 2 (00 = channel not used)

C3 = code for sensor on channel 3 (00 = channel not used)

PS = power supply option

Currently available channel options include:

Temperature

Humidity

Voltage

Current

Pulse Counting

Not all combinations are possible, please check with factory before ordering.

For parameters not listed, please contact our sales team on +44 (0)1462 688070

or email [email protected].

For further information and a full list of part numbers, visit www.hanwell.com/isense-spec

Each iSense unit requires a valid sim card contract and adequate network coverage at the

intended location.

iS

EN

SE

G

PR

S T

RA

NS

MIT

TE

R

IS – iSense Basic Module

Never compromising on craftsmanship, we have enhanced our products and services

through design and manufacture, with all units being produced at our facility within the UK.

We pride ourselves in our ability to accurately interpret customer requirements. If you

require the monitoring of any substance or element not mentioned in this brochure, please hure, please hure, please

call as we will, almost certainly, have a solution for you.

C1 C2 C3 PSIS:


Instrumentation for Science and IndustryRue du Doyenné, 31180 - BrusselsBelgium

T: +32 (2)343 30 81

W: www.isi-be.com

Contact

CO

NT

AC

T


Documents

Model: Product Name: Product Code: SR2 · Dimensions 300 x 200 x 85mm Weight 1.2kg ... ISI sa-nv - Instrumentation for Science and Industry ... main system administrator Network Server