30
www.royalgourmetcorp.com hotline Model: MG6001-R [email protected]

Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

  • Upload
    others

  • View
    8

  • Download
    0

Embed Size (px)

Citation preview

Page 1: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

www.royalgourmetcorp.com

hotline

Model: MG6001-R

[email protected]

Page 2: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

18

22

23-24

25-26

29

Preparation 67-17

181920-21

Trouble Shooting Guide

Warranty and Customer Service

Grilling Recipes 27-28

LP Gas and Cylinder Information

Cylinder Specifications

LP Cylinder Leak Test

Page 3: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

or hot.

hotline.

at

serious

Page 4: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

36"

36"

AT ALL TIMES .

Page 5: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

3

10

1

7

119

65

14 17

12

18

2

13

19

24

20

26

25

29

31

32

27

28

33

34

8

1615

2122

23

30

38

39

4

40

42

43

36

35

3741

11

4

Page 6: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

G H I 8pcs Split pin

A BM5X10 71pcs M6X12 24pcs

1 2 3 4

5 6 7 8

9 10 11 12

13 14 15 16

17 18 19 20

21 22 23 24

25

Rear board 1pc

Warming rack right 1pc

26 27 28

29 30 31 32

33 34

38

35 36

Handle right 1pc37 39 40

42 4341

D E F

J K M

8pcsM5X15 1pc 3pcs

M4X8 14pcs 4pcs M6X10 1pc 4pcs M10 8pcs

Magnet

Door screw M6

Caster 4pcs Bottom shelf 1pc Side shelf right 1pc Side shelf left 1pc

Middle shelf 1pc Rear shelf right 1pc Rear shelf left 1pc Middle panel 1pc

Connect panel 1pc Cart front beam 1pc Firebox brace 2pcs Middle brace 1pc

Handle base 8pcsDoor handle 4pcsRight door 1pc Left door 1pc

Middle door 2pc Grease cup base 2pcs Grease cup 2pcs Grease tray left 1pc

Grease tray right 1pc Thermal baffle 1pc Firebox 1pc Side burner shelf 1pc

Side table 1pc Side burner 1pc Side burner brace 1pc Rear burner 1pc

Electrode 1pc Rear burner board 1pc Flame tamer 6pcs

Cooking grate 3pcs

Thermometer 1pc Extension wire 1pc

Tank base lower 1pc Tank base upper 1pc

Warming rack left 1pc

Handle bracket 4pcs Handle left 1pc

Grill rotisserie base 2pcsW-M61A6401

W-M61A6402

W-53640002

Z-M6BPS060

Z-M61A6221

Z-M61A6616 Z-M61A6437

ZH-M61A634

ZH-M61A635

W-M61A6309+W-M61A6303

H-M61A6604 Z-M61A6331Z-M61A6332

H-M61A6601

ZH-M61A658ZH-M61A659 W-M61A6313

Z-M61A6325

Z-M61A6603Z-M61A6604

Z-DXL12047

W-52930001

W-M61A6314 Z-M61A6308

Z-M61A6421

Z-M61A6436

W-20130049 W-GD430013

W-M61A6201 W-M61A6310

Z-A3127-RGC Z-A3128-RGCZ-20130060

W-M61A6336

W-A0403

H-M61A6607 Z-M61A6608

Z-M61A6609 Z-M61A6322 Z-M61A6612

ZH-M61A668+ZH-M61A669

W-M61A6310+W-M61A6303

C M5X60 4pcs

2pcsL M6X15

Page 7: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

CALIFORNIA PROPOSITION 65 WARNING!1. Fuels used in gas burning appliances and the combustion byproducts of such fuels, can expose you to chemicals including carbon monoxide, which is known to the State of California to cause birth defects or other reproductive harm.

2. This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer. Handling the brass material on this product can expose you to lead, a chemical known to the State of California to cause cancer, birth defects or other reproductive harm.

For more information go to: www.P65Warnings.ca.gov

Page 8: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

2

A

1

3

B

4

5 B

A

6

Page 9: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

A

7

B

B

8

A

A

9

Assemble the rear shelf left (7) to left side shelf,

3

Page 10: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

A

A

D

111210

A

A

firebox

Page 11: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

13 14

15 16

10

G

E

B

42

B43

H

14

15

M

13

16

H

M

17

F

Install tank base upper (43) to the bottom shelf

42 M

M

Page 12: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

17 18

19 20

11

A

1819

2021

23

35

C

Assemble handle brackets (35) to lids with 8 bolts (C).

Page 13: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

21 22

23 24

B

37

36

IA

24

I

23

Insert the handles (36)(37) to handle brackets, secure them from inside of the lids with 4 bolts (B).

12

G

22

Page 14: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

25 26

27 28

25

I

K

K26

J

2

2 split pin

13

Page 15: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

29 30

31 32

L

27

G

G

28

burner brace (27), secure it with 1 nut (L).

14

Page 16: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

33 34

35 36

L

15

7

G

29

A

30

Page 17: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

37 38

39 40

G

31

33

38

16

32

38

34

39

39

Page 18: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

41 42

43 44

40

A

41

Assemble the grill rotisserie bases (41) to the firebox with 4 bolts (A).Recommended length for the grill rotisserie is 51".Grill rotisserie is not included.

17

40

not included

A

Assemble the hose brace to side shelf left with 2 bolts (A).

Page 19: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

Your new gas grill operates on LP (Liquid Petroleum)Gas.It is odorless,colorless,and non-toxic when produced. You can smell LP gas as it has been given an odor similar to rotten cabbage for your safety.

Never leave the grill unattended or move the grill when in use.

It will provide you with many years of enjoyment but a minimal amount of maintenance needed.

when the burners go out in cookingwhen

air vent

reconstructive

Do not obstruct the flow of air for combustion and ventilation.

18

Page 20: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

19

Page 21: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

metrics

cleaning products

Production of bubbles indicates a gas leak.

20

Page 22: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

er

at all times.

regulator

regulator

21

Page 23: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

22

Page 24: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

23

The grease tray should be emptied and wiped down in a mild detergent and warm water solution. A small amount of sand or cat litter may be placed in bottom of grease tray to absorb the grease.

GREASE TRAY / CUP

Page 25: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

24

Page 26: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

Trouble Shooting Guide

Emergencies Possible cause Prevention/ Solution

Troubleshooting: Problem Possible cause Prevention/ Solution

Gas leaking from cracked/cut/burned hose

Grease fire or continuous excessive flames above cooking surface

Too much grease buildup in burner area

Turn off LP Tank. Leave lid open to allow flames to die down. After cooling, clean food particles and excess grease from inside firebox area, grease cup/pan/tray, and other surfaces

Burner will not light using ignitor

Burner will not light using ignitor

Gas issues1. Trying to light wrong burner2. Burner not engaged with control valve3. Obstruction in burner4. No gas flow5. Vapor lock at coupling nut to LP tank6. Coupling nut and LP tank valve not fully connected.

Electrical issues:1. Electrode cracked or broken;” sparks at crack.”2. Electrode tip not in proper position3. Wire and/or electrode covered with cooking residue.4. Wires are loose or disconnected5. Wires are shorting (sparking) between igitor and electrode.6. Push button sticks at bottom sparking between ignitor and electrode

1. Replace electrode.2. Tip of electrode should be pointing toward port hole in burner. The distance should be 1/8” to 3/16”. Adjust if necessary.3. Clean wire and or electrode with rubbing alcohol and clean swab.4. Reconnect wires or replace electrode/ wire assembly.5. Replace ignitor wire6. Replace ignitor7. Inspect wire insulation and proper connection. Replace wires if insulation is broken.

1. See instructions on control panel and section in the Use and Care.2. Make sure valve are positioned inside of burner tubes.3. Ensure burner tubes are not obstructed with spider webs or other matted, see cleaning section of use and care4. Make sure LP tank is not empty. If LP tank is not empty, refer to “sudden drop in gas flow.5. Turn off knobs and disconnect coupling nut from LP tank. Reconnect and retry.6. Turn the coupling nut approximately one-half to three-quarters

Damaged hoseTurn off gas at LP tank, if hoes is cut or cracked, replace hose.See LP tank lead test and connection regulator to the LP

Gas leaking from LP tank Mechanical failure due to resting or mishandling Turn off LP tank valve

Failure or tank valve from mishandling or mechanical failure

Turn off LP tank valve. Return LP tank to gas supplier

Improper installation, untight connection , failure of rubber seal

Turn off LP tank valve, remove regulator from cylinder and visually inspect rubber seal for damage, see LP tank test and connection regulator to the LP tank

Turn off control knobs and LP tank valve. After fire is out and grill is cold, remove burner and inspect for spider nests or rust. see natural hazard and cleaning the burner assembly pages.

Fire in burner tube section of burner due to partial blockage

Gas leaking from LP tank valve

Gas leaking between LP tank and regulator connection

Fire coming through control panel

25

Page 27: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

Troubleshooting: Problem

Burner will not match light

Sudden drop in gas flow or low flame

Flames blow out

Persistent grease fire

Flashback…(fire in burner tube(s)

Flare-up

Unable to fill LP tank

One burner does not light from other burner(s)

See ”gas issues;” on previous page.2. Improper method of match-lighting

1. Grease buildup.2. Excessive fat in meat.3. Excessive cooking temperature

High or gusting winds. Low on LP gas.Excess flow valve tripped.

Grease trapped by food buildup around burner system.

Burner and burner tubes are blocked

1. Grease buildup.2. Excessive fat in meat.3. Excessive cooking temperature

Some dealers have older fill nozzles with worn threads.

Grease buildup or food particles in end of carryover tube

Turn knobs to OFF. Turn gas off at LP tank. Leave lid in position and let fire burn out. After grill cools, remove and clean all parts

Turn knobs to OFF. clean burnerand/or burner tubes. See burner cleaning section of use and care manual

1. Clean burners and inside of grill/ firebox2. Trim fat from meat before grilling.3. Adjust (lower) temperature

Turn worn nozzles don’t have enough “bite” to engage the valve. Try a second LP dealer.

Clean carry-over tube with wire brush

Turn front of grill to face wind or increase flame height.Refill LP tank.Refer to “sudden drop in gas flow” above.

1. See “Pilot Gas Control Ignition” section of use and care.

1. Clean burners and inside of grill/ firebox2. Trim fat from meat before grilling.

Possible cause Prevention/ Solution

If your problem is not resolved from the information above, please Contact your local gas dealer.

a) Turn the burner on for 15 to 20 minutes. Ensure appliance is cold before continuing.b) Grids should be cleaned periodically by soaking and washing in soapy water.c) The interior surfaces of the grill housing cover should also be washed with hot, soapy water. Use a wire brush, steel wool or a scouring pad to remove stubborn spots.d) Periodically check the burner to see that it is free from insects and spiders which may clog the gas system, deflecting gas flow. Ensure to clean venturi pipes on burner very carefully, make sure that there are no obstructions. We recommend that you use a pipe cleaner to clean the venturi pipe area.e) Any modifications of this appliance may be dangerous and are not permitted.

Safety Reminders

Stand your gas grill on a safe level surface, away from inflammable items such as wooden fences or overhanging tree branches.Never use your gas grill indoors!Once lit do not move your gas grill or leave it unattended.Keep children and pets at a safe distance from the gas grill.Keep a fire extinguisher handy.The gas grill will become hot when in use, so handle lids etc. with the help of gloves.Ensure that the appliance has completely cooled down before storing.

Notes:

26

Page 28: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

Direct Heat

GRILLING RECIPES

27

Page 29: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

STEAK (& ALL MEATS): • Cook food on the charcoal side of the unit, directly above coals/heat. • To grill meats, raise fire grate to high position (hot) and sear for one minute on each side with the lid open to seal in flavor and juices. Then lower fire grate to medium position with lid closed and cook

• Control heat with dual dampers and adjustable fire grate.

Tip: Place grilled meat back in the marinade for

and juicier.

CAUTION: Boil extra marinade first to kill bacteria

MARINATED FLANK STEAK:• Mix marinade ingredients in nonmetal dish. • Let steak stand in marinade for no less than 4 hours in refrigerator. • Brown each side for 5 minutes, but center should remain rare. • Cut steak diagonally across the grain into thin slices before serving. • Grill with fire grate in high (hot) position with lid

Meat Marinade1/2 cup vegetable or olive oil1/3 cup soy sauce1/4 cup red wine vinegar2 tbsp lemon juice1 tsp dry mustard1 minced clove garlic1 small minced onion1/4 tsp pepper

QUAIL OR DOVES:

• Cover birds with good seasons and marinate overnight.• Pour remaining dressing and cover with Texas Pete Hot Sauce for 6 hours.• Wrap birds in thick bacon secured by a toothpick. • Place on grill. Keep turning until bacon is black. • Grill for 20 minutes. Sear with lid open and fi re

before lowering grate and closing lid. •

KABOBS: • Alternating on skewers any combination of meat, onions, tomatoes, green peppers, mushrooms,zucchini, circular slice of

scallops, lobster, chicken,

• Marinate the meat in refrigerator for several hours. • Grill each side approximately 7 minutes turning occasionally while basting with marinade. Leave a small amount of room between pieces in order

to desired doneness.

several minutes before serving – it will become tastier

remaining from the raw meat.

open or closed.

corn-on-the-cob, or pineapple. Meat could consist of shrimp, sausage, pork, beef, etc.

grate in high (hot) position for 1 minute on each side

Kabob Marinade:

1 cup soy sauce½ cup brown sugar½ cup vinegar½ cup pineapple juice2 tsp salt½ tsp garlic powder• Mix all ingredients in a saucepan and bring to boil.• Allow marinade to cool before marinating your meat in it.• Marinate beef in mixture a minimum of 4 hours.

HOT DOGS:• Grill with lid up and cooking grates in high(hot) position for approximately 6 minutes.• Turn every few minutes.

HAMBURGERS:

See meat marinade on prior pages. You may also marinate by allowing to stand in marinade for 1 or 2 hours at room temperture before cooking or let stand in covered dish in refrigerator up to 24 hours.• Bring to room temperature before cooking.• Mix in chopped onions, green peppers, salt, sear 3/4 inch patties on each side with cooking grates in high position for a few minutes.• Lower fi re grate to medium position and grill with lid down to avoid flare-ups.• Cook each side 3 to 7 minutes according to desired doneness.• Cook ground meat to 150 internally or until juice runs clear (free of blood) for prevention of E-coli. • Burgers can be basted with marinade when turning and/or other ingredients can be mixed in with the ground beef such as chili sauce or powder.

SHRIMP (Peeled) & CRAYFISH:

• Place on skewers.• Coat with melted butter and garlic salt.• Grill 4 minutes on each side or until pink. Cocktail sauce optional.

BAKED POTATOES:

• Rub with butter and wrap in foil and cook on grill with lid down for 50 minutes.• Turn after 25 minutes (no need to turn if smoked).• Squeeze to check for doneness.

SWEET CORN IN HUSKS:

• Trim excess silk from end and soak in cold salted water 1 hour before grilling.• Grill 25 minutes – turning several times.

To smoke and place brids in center of grates with fire in both ends of fire box.

Grill with lid up and the cooking grates in the lowest position.

to cook faster.•

28

Page 30: Model: MG6001-R€¦ · 4. No gas flow 5. Vapor lock at coupling nut to LP tank 6. Coupling nut and LP tank valve not fully connected. Electrical issues: 1. Electrode cracked or broken;”

[email protected]

Corp

prior to obtain

MG6001-R

29