3
1 Bravat (China) GmbH Customer Supports:[email protected] 15123803 15123803 Bravat (China) GmbH Customer Supports:[email protected] 4 MODEL: ERF2212254CP-10 ERF2212254AP-10 ERF2212254HA-10 Description: Widespread Lavatory Faucet PRODUCTS INSTALLATION INSTRUCTIONS A HELPFUL TOOLS E SPECIFICATION Before installing the new mixer, it is essential that you thoroughly flush through the supply pipes in order to remove any remaining swarf, solder or other impurities. Failure to carry out this simple procedure could cause problems or damage to the workings of the mixer. Work water pressure: 10-100 psi(Including cold and hot). If the pictures and statements in the ‘Installation Specifications’ is unconfirmed with practicality, please take practicality as standard. Points for attention before installation Application: Operation with unpressurized storage heaters is not possible. Use for indoor public places and common residence. Specifications Flow pressure: min. 10 psi – recommended 20 – 100 psi Operating pressure: max. 125 psi Test pressure: 60 psi Flow rate at 60 psi flow pressure for basin: 1.2 gpm Hot water inlet temperature: max. 90Recommended (energy saving): 60Environment temperature: 545If static pressure exceeds 100 psi, a pressure-reducing valve must be fitted. Avoid major pressure differences between hot and cold water supply. This technical product information is exclusively for the installer or trained specialists. Please pass these instructions on to the user. GB Installation: Flush piping system prior and after installation of fitting thoroughly! Fitting a temperature limiter is possible. Function: Check connections for leaks and check function of fitting. Maintenance: Inspect and clean all components and replace if necessary. Shut off water supply for maintenance work. When installing the cartridge, ensure that the seals are correctly seated. Tighten the screws evenly and alternately. Replacement parts: see exploded drawing. Care: see Care Instructions. F MAINTENANCE CAUTION: Always turn water OFF before removing existing or disassembing the faucet. Open faucet handles to relieve water pressure and insure that complete water shut-off has been accomplished. To keep the surface clean and bright, please clean the faucet regularly,please abide by the following procedures: 1. Use rinsing water and soft cloth, clean bilge and bilge membrane on the surface to the best of the abilities. 2. Cleaned the residua with the following cleansers only. 3. After cleaning, use rinsing water to clean all cleanser immediately and drying with a soft cotton cloth. 4. Carefully dismantle the aerator regularly, rinse under clean running water until any loose debris is cleared to avoid the influence to water outflow. Soft liquid cleanser. Colorless glass cleanser, totally soluble powder cleanser without abrasive capability.(Mixed by instructions.) No abrasive cleansers waxes. Never use cleanser, emery cloth or handkerchief which can rub. Never use cleaners containing abrasive cleansers, ammonia,bleach, acids, waxes, alcohol, solvents or other products not recommended for chrome. G SPECIAL STATEMENT The products installation instruction is written in accordance with the latest product information, following the sustainable develop- ment strategy of the Company, to improve continually the produce's specification, performance etc.,subject to change without notice. (The Company reserves the right to interpret) NO. NAME QTY. 1 Lift Knob 1 2 Screw 2 3 Handle 1 4 Screw 2 5 Connector 2 6 Nut 2 7 Cartridge(Hot) 1 8 Base 2 9 Nut 2 10 O-Ring 2 11 Body 2 12 Washer 2 13 Washer 2 14 Nut 2 15 Screw 4 16 Pop-Up Assembly 1 17 Hose 2 18 Water Joint Components 1 19 Washer 1 20 Nut 1 21 Washer 1 22 Rubber Washer 1 23 Pipe 1 24 Lift Rod 1 25 O-Ring 1 26 Washer 1 27 Base 1 28 Cartridge(Cold) 1 29 Spout 1 30 Handle 1 31 Allen Key 1 32 Aerator 1 33 O-Ring 1 34 Base 1 Spanner Teflon tape Screwdriver Flashlight

MODEL: ERF2212254CP-10 E SPECIFICATION ERF2212254AP …images-na.ssl-images-amazon.com/images/I/B11TNRqDMJS.pdf10 O-Ring 2 11 Body 2 12 Washer 2 13 Washer 2 14 Nut 2 15 Screw 4 16

  • Upload
    others

  • View
    0

  • Download
    0

Embed Size (px)

Citation preview

Page 1: MODEL: ERF2212254CP-10 E SPECIFICATION ERF2212254AP …images-na.ssl-images-amazon.com/images/I/B11TNRqDMJS.pdf10 O-Ring 2 11 Body 2 12 Washer 2 13 Washer 2 14 Nut 2 15 Screw 4 16

1Bravat (China) GmbH Customer Supports:[email protected] (China) GmbH Customer Supports:[email protected] 4

MODEL: ERF2212254CP-10 ERF2212254AP-10 ERF2212254HA-10

Description: Widespread Lavatory FaucetPRODUCTS INSTALLATION INSTRUCTIONS

A HELPFUL TOOLS

E SPECIFICATION

Before installing the new mixer, it is essential that you thoroughly flush through the supply pipes in order to remove any remaining swarf, solder or other impurities. Failure to carry out this simple procedure could cause problems or damage to the workings of the mixer. Work water pressure: 10-100 psi(Including cold and hot). If the pictures and statements in the ‘Installation Specifications’ is unconfirmed with practicality, please take practicality as standard.

!Points for attention before installation

Application:Operation with unpressurized storage heaters is not possible.Use for indoor public places and common residence.

SpecificationsFlow pressure: min. 10 psi – recommended 20 – 100 psiOperating pressure: max. 125 psiTest pressure: 60 psiFlow rate at 60 psi flow pressure for basin: 1.2 gpmHot water inlet temperature: max. 90℃Recommended (energy saving): 60℃Environment temperature: 5℃~45℃

If static pressure exceeds 100 psi, a pressure-reducing valve must be fitted.

Avoid major pressure differences between hot and cold water supply.

This technical product information is exclusively for the installer or trained specialists.Please pass these instructions on to the user.

GBInstallation:Flush piping system prior and after installation of fitting thoroughly!Fitting a temperature limiter is possible.

Function:Check connections for leaks and check function of fitting.

Maintenance:Inspect and clean all components and replace if necessary.Shut off water supply for maintenance work.

When installing the cartridge, ensure that the seals are correctly seated.Tighten the screws evenly and alternately.

Replacement parts: see exploded drawing.Care: see Care Instructions.

F MAINTENANCE

CAUTION: Always turn water OFF before removing existing or disassembing the faucet. Open faucet handles to relieve water pressure and insure that complete water shut-off has been accomplished.

To keep the surface clean and bright, please clean the faucet regularly,please abide by the following procedures:

1. Use rinsing water and soft cloth, clean bilge and bilge membrane on the surface to the best of the abilities.2. Cleaned the residua with the following cleansers only.

3. After cleaning, use rinsing water to clean all cleanser immediately and drying with a soft cotton cloth.4. Carefully dismantle the aerator regularly, rinse under clean running water until any loose debris is cleared to avoid the influence to water outflow.

Soft liquid cleanser.Colorless glass cleanser, totally soluble powder cleanser without abrasive capability.(Mixed by instructions.)No abrasive cleansers waxes.Never use cleanser, emery cloth or handkerchief which can rub.Never use cleaners containing abrasive cleansers, ammonia,bleach, acids, waxes, alcohol, solvents or other products not recommended for chrome.

G SPECIAL STATEMENT

The products installation instruction is written in accordance with the latest product information, following the sustainable develop-ment strategy of the Company, to improve continually the produce's specification, performance etc.,subject to change without notice. (The Company reserves the right to interpret)

NO. NAME QTY.1 Lift Knob 12 Screw 23 Handle 14 Screw 25 Connector 26 Nut 27

Cartridge(Hot) 1

8

Base 2

9

Nut 2

10

O-Ring 2

11

Body 2

12

Washer 2

13

Washer 2

14

Nut 2

15

Screw 4

16

Pop-Up Assembly 1

17

Hose 2

18

Water Joint Components 1

19

Washer 1

20

Nut 1

21

Washer 1

22

Rubber Washer 1

23

Pipe 1

24

Lift Rod 1

25

O-Ring 1

26

Washer 1

27

Base 1

28

Cartridge(Cold) 1

29

Spout 1

30

Handle 1

31

Allen Key 1

32

Aerator 1

33

O-Ring 1

34

Base 1

Spanner

Teflon tapeScrewdriver Flashlight

Page 2: MODEL: ERF2212254CP-10 E SPECIFICATION ERF2212254AP …images-na.ssl-images-amazon.com/images/I/B11TNRqDMJS.pdf10 O-Ring 2 11 Body 2 12 Washer 2 13 Washer 2 14 Nut 2 15 Screw 4 16

3Bravat (China) GmbH Customer Supports:[email protected] (China) GmbH Customer Supports:[email protected]

B INSTALLATION DIMENSION

D FAUCET OPERATION

C INSTALLATION STEP

Unit: inch

6 75

1 2 3 4

9 108

Hot

90° 90°

Cold

Close Close

Open Open

Length 11 13/16"

4" 4"

2-1/2-14 NPSM

Max

1 1

/2"

Max

1 3

/8"

1 1/4"

6 5/16"8 3/

16"

3 5/

8"

4 1/

4"6 3/

16"

5 1/4"

7"

2 1/8"

2 15/16"

2 1/16"

1 9/16"- 1 13/16"

1 1/4"- 1 1/2"1 1/4"-1 1/2"

2 1/16"

Open drainage

Close drainage

A

B

Page 3: MODEL: ERF2212254CP-10 E SPECIFICATION ERF2212254AP …images-na.ssl-images-amazon.com/images/I/B11TNRqDMJS.pdf10 O-Ring 2 11 Body 2 12 Washer 2 13 Washer 2 14 Nut 2 15 Screw 4 16

151238039L173101CP英文说明书

王少凤 陈贵鸿

刘恒良 彭俊毅

2016-09-30

100g双胶纸

技术要求:1.尺寸:A4对折,A5版面;2.印刷:双面单色印刷;3.纸张:100克双胶纸;4.说明书不需装订;5.页数:4页;6.此图主要做规格描述,实际印刷依照后4页。

理论重量 [g]

[cm ]3

[cm ]2

[cm ]2

理论体积

理论面积

理论表面积

客户版本---

---

---

--- ---

---

---客户编号

绘图单位 mm

比 例

设 计 审 核

校 对 批 准

日 期

图 号

材料

第 1 页/共 1 页

广东省广州市番禺区沙头街禺山西路363号版次 处数 ECN编号

A

4

3

2

1

4

3

2

1

B C D

A B C D

更改人 日 期

声明:本图为机密文件,版权归广州海鸥卫浴用品股份有限公司所有,未经本公司的书面许可不得擅自使用、复制、或向他人展示。