MODEL ER-A440 - Inland Cash Register is now Point Of ...... Turn off the AC switch. 2) Set the mode switch to (SRV ′) position. 3) Turn on the AC switch. 4) Turn to (SRV) position

ELECTRONICCASH REGISTER

MODEL ER-A440(For "U" & "A" version)SRV KEY : LKGIM7113RCZZPRINTER : DP-730

SHARP CORPORATIONThis document has been published to be usedfor after sales service only.The contents are subject to change without notice.

CHAPTER 1. SERVICE (SRV) MODE . . . . . . . . . . . . . . . . . . . . . . . . . . 1

CHAPTER 2. PROGRAM (PGM2/PGM1) MODE. . . . . . . . . . . . . . . . . 15

CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE . . . . . . . . . . . . . . . . . . . . . 36

CONTENTS

CHAPTER 1. SERVICE (SRV) MODE

The SRV key is used for operating in the SRV mode.

1. SRV. reset (Program Loop Reset)

Used to return the machine back to its operational state after a lock-up has occurred.

Procedure• Method 1

1) Turn off the AC switch.

2) Set the mode switch to (SRV′) position.

3) Turn on the AC switch.

4) Turn to (SRV) position from (SRV′) position.

• Method 2

1) Set the mode switch to PGM2 position.


3) While holding down JOURNAL FEED key and RECEIPT FEEDkey, turn on the AC switch.

Note: When disassembling and reassembling always power up us-ing method 1 only. Method 2 will not reset the CKDC8.

Note: SRV programming job#926-B must be set to "4" to allow PGMprogram loop reset.

PRG. RESET

2. Master reset (All memory clear)

There are two possible methods to perform a master reset.

• MRS-1Used to clear all memory contents and return machine back to itsinitial settings. return keyboard back to default. for default key-board layout.

Procedure


2) Set the MODE switch to the (SRV′) position.


4) While holding down JOURNAL FEED key, turn to (SRV) positionfrom (SRV′) position.

• MRS-2Used to clear all memory and keyboard contents.This reset returns all programming back to defaults. The keyboardmust be entered by hand.This reset is used if an application needs different keyboard layoutother than that supplied by a normal MRS-1.

Procedure


2) Set the MODE switch to the (SRV′) position.


4) While holding down JOURNAL FEED key and RECEIPT FEEDkey, turn to (SRV) position from (SRV′) position.

5) Key position assignment:

After the execution of MRS-2, only the RECEIPT FEED andJOURNAL FEED keys can remain effective on key assignment.Any key can be assigned on any key position on the main key-board.

[key setup procedure]

MASTER PRESET

NOTES:

1: When the 0 key is pressed, the key of the key number ondisplay is disabled.

2: Push the key on the position to be assigned. With this, the keyof the key number on display is assigned to that key position.

Key number Key name Key number Key name

1 Numeric key "0" 10 Numeric key "9"



4 Numeric key "3" 13 Decimal point key

5 Numeric key "4" 14 CL key

6 Numeric key "5" 15 @/FOR key

7 Numeric key "6" 16 SBTL key

8 Numeric key "7" 17 CA/AT key

9 Numeric key "8"

3. Reading of the SRV mode program

List of program reports

JOB# Report name

900SRV-mode program full item report (not incl. keyboardlayout)

950Keyboard layout report (on keys other than dept. keysand direct PLU keys)

951Keyboard layout report (on dept. keys and direct PLUkeys)

970 SRV file programming report

MRS-2 executed Key position set Free key

Disable

Free key setupcomplete.

*2

*1

0

0

– 1 –

[JOB# 900]All parameters contained for the SRV mode as listed

Key operation.

900 → @/FOR → CA/AT

Header logo

Data/ Time

Machine No./ Consective No.

JOB#

JOB#/ Programmingdata(ABCD)

Z1 reset counter

Hourly Z1 counter

GT2 counter

Training GT

Secret code for PGM2 mode

Initial text mode programming

PLU Z1/Z2 reset counter

Cashier Z1/Z2 reset counterZ2 reset counterDaily net Z2 reset counter

GT3 counter

– 2 –

[JOB# 950]The Key layout report is printed in SRV mode

Key operation

950 → @/FOR → CA/AT

Header logo

Data/ Time


JOB#

Key No./ Key label name/Location No.

Key No./ Key label name/Location No.(....: Not used)

– 3 –

Key operation

951 → @/FOR → CA/AT

Header logo

Data/ Time


JOB#

Key No./ Key label name/Location No. Key No./ Key label name/

Location No.(....: Not used)

– 4 –

[JOB#970]Files on the memory are listed.

Key operation

970 → @/FOR → CA/AT

[JOB#990]Reading the Contents of the SRV-Mode Programming for SSP

Key operation

990 → @/FOR → CA/AT

Header logo

Data/ Time


JOB#

File table No./ No. of records/No. of used records

File memory start address

Empty memory start address

Memory end address

File table No./ No. of records/No. of blocks/ No. of used records

Header logo

Data/ Time


JOB#

SSP No.Step No./ SSP data

Error message

– 5 –

4. Service mode programming

The following are the key operation required for programming.

Details of [A][B][C][D] will be discussed at each item description.

★ mark is MRS setting.

[JOB #901]:MRS=0002 [For "U" version]#901-A, B: Not used (Fixed at "00")

#901-C: 1. Rounding system

1. Rounding system 901-C

Normal 0 ★

SINGAPORE 8

#901-D: 1. TAB setting

1. TAB setting 901-D

0 0

0.0 1

0.00 2 ★

0.000 3

[JOB #901]: MRS=0002 [For "A" version]#901-A: Not used (Fixed at "0")

#901-B: 1. Tax system

1. Tax system 901-B

Auto tax 1-4 & manual tax 0 ★

CANADIAN TAX 6

#901-C: 1. Rounding system

1. Rounding system 901-C

Normal 0 ★

SINGAPORE 8

#901-D: 1. TAB setting

1. TAB setting 901-D

0 0

0.0 1

0.00 2 ★

0.000 3

[JOB#902] NOT USED MRS=0000

[JOB#903] MRS=4000#903-A: 1. ECR data copy baud rate

1. Baud rate (bps) 903-A

2400 2

4800 3

9600 4 ★

19200 5

38400 6

The communication speed with the ER-02FD is max.19200 bps.

#903-B, C: Not used (Fixed at "00")

#903-D: 1. Type of food stamp

1. Type of food stamp 903-D★No food stamp 0

Tax not payable in food stamps 1

Tax payable in food stamps 2

Food stamp tax forgiveness 3

[JOB#904] MRS=0000

#904-A: 1. Printing of date

1. Printing of date 904-A★Yes 0

No 4

#904-B: 1. Printing of consecutive No.

1. Printing of consecutive No. 904-B★Yes 0

No 4

#904-C, D: Not used (Fixed at "00")

[JOB#905] MRS=0005 [For "U" version]#905-A: 1. Taxable 4 subtotal print on X/Z report.

2. Gross Tax 4 and refund Tax 4 total print on X/Z report.

3. Net Tax 4 total print on X/Z report.

1. Taxable 4SBTL

2. Gross Tax 4and refundTax 4

3. Nex Tax 4905-A

PrintPrint

Print 0 ★

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

#905-B: 1. Tax printing when taxable subtotal is zero.

2. Tax printing when tax is zero.

1. Taxable subtotal iszero

2. Tax is zero905-B

SkipPrint 0 ★

Skip 1

PrintPrint 4

Skip 5


XXX CA/AT

(Job#)

[A] [B] [C] [D]

Numeric entry4 digits max

0

@/FOR

– 6 –

[JOB#905] MRS=0005 [For "A" version]#905-A: 1. Taxable 4 subtotal print on X/Z report.

2. Gross Tax 4 and refund Tax 4 total print on X/Z report.

3. Net Tax 4 total print on X/Z report.

1. Taxable 4SBTL

2. Gross Tax 4and refundTax 4

3. Nex Tax 4905-A

PrintPrint

Print 0 ★

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

#905-B: 1. Tax printing when taxable subtotal is zero.2. Tax printing when GST is VAT.3. Tax printing when tax is zero.

1. Taxablesubtotal is zero

2. GST isVAT

2. Tax is zero905-B

SkipPrint

Print 0 ★

Skip 1

SkipPrint 2

Skip 3

PrintPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

#905-C: 1. GST EXPT print on X/Z report

1. GST EXPT 905-C

Print 0 ★

Skip 4

#905-D: 1. TAX METHOD

Tax4method (GST)

Tax3 method Tax2, 1method (PST)

905-DGST PST

Type VAT VAT

Tax on Tax 0

Type Tax on Base 1

Type VAT

Tax on Tax 2

Type Tax on Base 3

Type Add on Tax

Tax on Tax 4

Type Tax on Base 5 ★

Type Add on Tax VAT

Tax on Tax 6

Type Tax on Base 7

Type Add on Tax

Addon Tax

Tax on Tax 8

Type Tax on Base 9

[JOB#906] MRS=0021#906-A: 1. Print Dept. and PLU number on receipt.

1. Print Dept. and PLU number on receipt. 906-A

No 0 ★

Yes 4

#906-B: 1. Bottle return function

2. Hash department setting

1. Bottle return function 2. Hash departmentsetting

906-B

DisableDisable 0 ★

Enable 2

EnableDisable 4

Enable 6

#906-C: 1. Split pricing counting

2. Multiplication entry

1. Split pricing counting 2. Multiplication entry 906-C

Quantity

Multiplication 0

Successivemultiplication

1

Split pricing 2 ★

Package

Multiplication 4

Successivemultiplication

5

Split pricing 6

#906-D: 1. Presetting consecutive No.

2. Fractional quantity

1. Presettingconsecutive No.

2. Fractional quantity906-D

YesNo 0

Yes (3 digit decimalplace)

1 ★

NoNo 2

Yes (3 digit decimalplace)

3

[JOB#907] MRS=0010#907-A, B: Not used (Fixed at "00")

#907-C: 1. Minus Dept./PLU

1. Minus Dept./PLU 907-C

Disable 0

Enable 1 ★

#907-D: Not used (Fixed at "0")

[JOB#908] MRS=0740#908-A: GT print on Z report

GT1 (NET) GT2 (+) GT3 (–) 908-A

PrintPrint

Print 0 ★

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

– 7 –

#908-B: GT print on X report

GT1 (NET) GT2 (+) GT3 (–) 908-B

SkipSkip

Skip 0

Print 1

PrintSkip 2

Print 3

PrintSkip

Skip 4

Print 5

PrintSkip 6

Print 7 ★

#908-C: 1. Add void-mode transaction data to hourly total report

2. X1/Z1 report in X2/Z2 mode

3. Resetting of consecutive number in Z1 resetting

1. Addvoid-modetransactionto hourlytotal report

2. X1/Z1 reportin X2/Z2mode

3. Resetting ofconsecutiveNo.in Z1resetting

908-C

NoEnable

No 0

Yes 1

DisableNo 2

Yes 3

YesEnable

No 4 ★

Yes 5

DisableNo 6

Yes 7

#908-D: 1. Printing X/Z report Journal only/Receipt & Journal (Ex-cept the individual cashier report)

2. Z1 resetting, resets GT Enable/Disable

1. Printing X/Z report 2. GT resetting at Z1 908-D

Receipt & JournalDisable 0 ★

Enable 1

JournalDisable 4

Enable 5

[JOB#909] MRS=2000#909-A: 1. Printing of training GT on the X report

2. Printing of training GT on the Z report

1. Printing of trainingGT on the X report

2. Printing of trainingGT on the Z report

909-A

SkipPrint 0

Skip 1

PrintPrint 2 ★

Skip 3

#909-B: 1. Printing of data on PLU resetting report

1. Printing of data on PLU resetting report 909-B

Print 0 ★

Skip 4

#909-C: 1. Printing of data in void-mode totalizer and managervoid totalizer on Z2 report

2. Printing of data in void-mode totalizer and managervoid totalizer on Z1 report

1. Void-mode totalizeron Z2 printing

2. Void-mode totalizeron Z1 printing

909-C

PrintPrint 0 ★

Skip 2

SkipPrint 4

Skip 6


[JOB#910] MRS=0004#910-A: Not used (Fixed at "0")

#910-B: 1. Cashier # on display

2. Auto cashier sign off at the end of each transaction

1. Cashier # on display 2. Auto cashier sign offat the end of eachtransaction

910-B

HiddenNo 0

Yes 1

AppearNo 2 ★

Yes 3


[JOB#911] MRS=0100#911-A: 1. Fraction treatment

1. Fraction treatment 911-ARound off 0 ★

Round up 1Round down 2

#911-B, C, D: Not used (Fixed at "000")

[JOB#912] MRS=0060#912-A: 1. Date print format

Date format 912-AMonth/Day/Year 0 ★

Day/Month/Year 1Year/Month/Day 2

#912-B: 1. Time system

1. Time system 912-B12H 0 ★

24H 1

– 8 –

#912-C: 1. After transaction receipt format

2. Copy receipt

3. Footer print control

1. Aftertransactionreceipt

2. Copyreceipt

3. Footer printcontrol 912-C

Total only

No

All receipt 0On selected functionkeys at the time offinalization

1

Yes


3

Detail

No


5

★

Yes


7

#912-D: 1. Logo message control

1. Logo/stamp message control 912-D3-line header 0 ★

3-line footer 26-line header 33-line header and 3-line footer 5

(Logo/stamp message format)

[JOB#913] MRS = 0104#913-A: 1. VP format on Receipt/Journal

2. Content of TOTAL VP amount

1. VP format onReceipt/Journal

2. Content of TOTALVP amount

913-A

Date & amountTotal amount 0 ★

Tendered amount 1

Machine No. & amountTotal amount 2Tendered amount 3

Date & Consective No.& amount

Total amount 4Tendered amount 5

#913-B: 1. Printing of SBTL

2. Printing of MDSE SBTL upon key depression

3. Escape the compulsion of VP

NOTE: Must turn to MGR mode and depress

• • , PRINT keys to escape validation

1. SBTL Print 2. MDSESBTL print

3. Escape thecompulsoryof VP

913-B

NoNo

Disable 0

Enable 1 ★

YesDisable 2

Enable 3

YesNo

Disable 4

Enable 5

YesDisable 6

Enable 7

#913-C: 1. Buzzer off 2sec. after lock error.

2. Buffered keyboard

1. Error beep 2. Buffered keyboard 913-C

2-sec. offYes 0 ★

No 1

ConstantYes 2

No 3

#913-D: 1. Drawer closing operation

2. Error mode

3. Key catch sound

1. Drawer closedcompulsory

2. Error mode 3. Key catchsound

913-D

Non-compulsoryAll lock error

Enable 0

Disable 1

Miss operation(One shot error)

Enable 2

Disable 3

CompulsoryAll lock error

Enable 4 ★

Disable 5

Miss operation(One shot error)

Enable 6

Disable 7

[JOB#914] MRS = 1100#914-A: 1. Receipt issuing at no-sale

2. [NS] key separation from [CA/AT] key for no sale func-tion

3. Tax delete operation

1. Receipt issuingat no-sale

2. [NS] keyseparation

3. Tax delete914-A

EnableYes

Inhibit 0

Enable 1 ★

NoInhibit 2

Enable 3

DisableYes

Inhibit 4

Enable 5

NoInhibit 6

Enable 7

Header

Footer

Type : 0 2 3 5

– 9 –

#914-B: 1. No-sale after NON ADD code entry

1. No-sale after # entry 914-B

Disable 0

Enable 1 ★

#914-C: 1. Action to be taken when the machine is locked by thereceipt/journal paper near end check

2. VOID mode

3. Non-add code entry at the beginning of a transactionoperation

1. Action to betaken whenthe machineis locked bythe journalpaper nearend check

2. VOID mode 3. Non-addcode entry atthe beginningof atransactionoperation

914-C

Unloked by CLkey

EnableNon-compulsory 0 ★

Compulsory 1

DisableNon-compulsory 2

Compulsory 3

Enforcing ofpaper roll

replacement

EnableNon-compulsory 4

Compulsory 5

DisableNon-compulsory 6

Compulsory 7

#914-D: 1. Manual tax

2. CHECK CASHING

3. Non-add code entry

1. Manual tax 2. CHECKCASHING

3. Non-addcode entry

914-D

EnableDisable

Enable 0 ★

Disable 1

EnableEnable 2

Disable 3

DisableDisable

Enable 4

Disable 5

EnableEnable 6

Disable 7

[JOB#915] MRS = 0000#915-A: 1. Amount symbol

1. Amount symbol 915-A" $ " 0 ★

" " 1" " 2

#915-B: Not used (Fixed at "0")

#915-C: 1. Paper near end check

2. ST%, ST(–) as many times needed/operation only once

1. Paper near end check 2. ST%, ST(–) as manytimesneeded/operationonly once

915-C

YesUnlimited 0 ★

Once only 2

NoUnlimited 4Once only 6


[JOB#916] MRS = 1400#916-A: 1. Print format when text and amount overlaps each other

REG mode

1. Print format when text and amountoverlaps each other REG mode

916-A

Truncate text 0

2 line print 1 ★

#916-B: 1. Finalization by charge when SBTL 0

2. Food stamp subtotal entry before food stamp tender

1. Finalization bycharge whenSBTL 0

2. Food stamp subtotalentry before food stamptender

916-B

RF type of sale onlyNon-compulsory 0

Compulsory 1

AlwaysNon-compulsory 4 ★

Compulsory 5

#916-C: 1. Negative merchandise subtotal

2. Subtotal entry compulsory before tendering

3. Subtotal entry before direct non-tendering finalization

1. Negativemerchan-disesubtotal

2. Subtotalentrycompulsorybeforetendering

3 .Subtotalentry beforedirectnon-tenderingfinalization

916-C

AllowNoncompulsory

Non-compulsory 0 ★

Compulsory 1

CompulsoryNon-compulsory 2

Compulsory 3

DisallowNon-compulsory

Non-compulsory 4

Compulsory 5

CompulsoryNon-compulsory 6

Compulsory 7

#916-D: 1. Coupon PLU printing on X/Z report

2. Net sales subtotal (NET1) printing on X/Z report

3. CHECK change total printing on X/Z report

1. Print couponPLU’s ongeneral report

2. Print netsales SBTL(NET1) ongeneral report

3. Print CHKCHANGE ongeneral report

916-D

PrintPrint

Print 0 ★

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

– 10 –

[JOB#917] MRS = 0000#917-A: 1. Printing of Taxable 1 subtotal on X/Z report

2. Printing of Gross Tax 1 and refund Tax 1 total on X/Zreport

3. Printing of Net Tax 1 total on X/Z report

1. Taxable 1subtotal onX/Z report

2. Gross Tax 1and refundTax 1 totalon X/Z report

3. Net Tax 1total on X/Zreport

917-A

PrintPrint

Print 0 ★

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

#917-B: 1. Printing of Taxable 2 subtotal on X/Z report






917-B

PrintPrint

Print 0 ★

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

#917-C: 1. Printing of Taxable 3 subtotal on X/Z report






917-C

PrintPrint

Print 0 ★

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

#917-D: 1. Printing of Total Tax amount on X/Z report

2. Printing of Gross manual Tax and refund manual Taxon X/Z

3. Printing of Net manual Tax total on X/Z report

1. Total TaxAmount

2. Grossmanual Taxand Refundmanual Taxon X/Z report

3. Net manualTax total onX/Z report 917-D

PrintPrint

Print 0 ★

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

[JOB#918] MRS = 2000#918-A: 1. Dirrect non-tendering finalization after previous tender

entry

1. Dirrect non-tendering finalization afterprevious tender entry

918-A

Disable 0

Enable 2 ★

#918-B, C, D: Not used (Fixed at "000")

[JOB#919] MRS = 0000#919-A, B: Not used (Fixed at "00")

#919-C: 1. Amount printing when PLU unit price is 0

1. Amount printing when PLU unit price is0

919-C

No 0 ★

Yes 1

919-D: 1. Conversion SBTL printing of native SBTL

2. Foreign currency format

1. Conversion SBTLprint of native SBTL

2. Foreign currency919-D

YesNot 0 ★

Omit digits lower thanTAB position

1

NoNot 4

Omit digits lower thanTAB position

5

[JOB#920] NOT USED MSR = 0000

[JOB#921] NOT USED MRS = 0000





– 11 –

[JOB#926] MRS = 0400#926-A: Not used (Fixed at "0")

#926-B: 1. Program reset at PGM 2 mode

1. Program reset at PGM2 mode 926-B

Disable 0

Enable 4 ★

#926-C: 1. Open store/Close store with on-line

2. Send AT command string with JOB#500 (Open store)

3. Send AT command string with JOB#501 (Close store)

1. Openstore/Closestore withon-line

2. Send ATcommandstring withJOB#500(Open store)

3. Send ATcommandstring withJOB#501(Close store)

926-C

NoNo

No 0 ★

Yes 1

YesNo 2

Yes 3

YesNo

No 4

Yes 5

YesNo 6

Yes 7

#926-D: 1. Receive on-line channel in close store

1. Receive on-line channel in close store 926-D

No 0 ★

Yes 4

[JOB#927] NOT USED: MRS = 0000

[JOB#928] NOT USED: MRS = 0000

[JOB#929] MRS = 0000#929-A, B, C: Not used (Fixed at "000")

#929-D: 1. Taxable status of PLU which is set at "Non-taxable" byPGM

1. Taxable status of PLU which is set at"Non-taxable" by PGM

929-D

According to its associated Department 0 ★

Non-taxable 2

[JOB#930 ∼941] MRS = 0000RESET REPORT COUNTER

JOB # Function

930 Z1 report counter

933 Hourly Z1 report counter

934 PLU Z1/Z2 report counter

935 Cashier Z1/Z2 report counter

937 Z2 report counter

939 31 day daily net Z2 report counter

[JOB#942, 943, 969] MRS = 0000000000000GT COUNTER PRESETTING

JOB # Function942 GT2 (Positive GT)943 GT3 (Negative GT)969 TRAINING GT

Note: GT1 is obtained by calculationEquation: GT1=GT2-GT3

[JOB#944] MRS = 0000PGM2 secret code presetting

NOTE: When the secret code "0" is programmed, the secret codeentry is be inhibited.

[JOB#950] MRS = STANDARD KEY LAYOUTFree key layout (Except for department keys and direct PLU keys.)

[JOB#951] MRS = STANDARD KEY LAYOUTFree key layout (department keys and direct PLU keys)

• Programming of the keys to be dept keys or direct PLU keys onthe keyboard.

• Key No. is assigned to each key which is supposed to be dept.Key or direct PLU key by depressing the key after entering the keyNo.

• Those keys programmed by this job No. will be dept. keys if dept.code is assigned, and will be direct PLU keys if PLU code isassigned in the PGM2 mode.

CA/ATJob# ABCD

Initial value of Z countr

@/FOR

"0000"

CA/ATJob# 000000000000013 digits

@/FOR

0

CA/AT944 XXXX4 digits

@/FOR

0

Free key@/FOR CA/AT

@/FOR

Key number automaticincrement

Key number manualincrement

Initial setting

XXXKey No.

To inhibitSBTL

increment key No.

950

Free key@/FOR CA/AT

@/FORKey No.

Key number automaticincrement

Key number manual increment

To inhibitSBTL

increment key No.

951 XXX

– 12 –

FUNCTION KEY LIST

Key No. KEY KEY TEXT

1 0 KEY 0 KEY

2 1 KEY 1 KEY

3 2 KEY 2 KEY

4 3 KEY 3 KEY

5 4 KEY 4 KEY

6 5 KEY 5 KEY

7 6 KEY 6 KEY

8 7 KEY 7 KEY

9 8 KEY 8 KEY

10 9 KEY 9 KEY

11 00 KEY 00 KEY

12 000 KEY 000KEY

13 DECIMAL POINT . KEY

14 CLEAR CLEAR

15 @/FOR @/FOR

16 SUB TOTAL SBTL

17 CA/AT CA/AT

18 MDSE SBTL MDS ST

19 # #

20 NO SALE NS

21 PLU/SUB PLU/SB

22 REFUND SALES RF SAL

23 TAX1 SHIFT TAX1SF




27 FS SHIFT FS SHT

28 PRINT PRINT

29 RCPT RCPT

30 VOID VOID

31 REFUND RFND

32 %1 %1

33 %2 %2

34 %3 %3

35 %4 %4

36 (–)1 (–)1

37 (–)2 (–)2

38 (–)3 (–)3

39 (–)4 (–)4

40 TAX TAX

41 AUTO AUTO

42 AUTO2 AUTO2

43 AUTO3 AUTO3

44 AUTO4 AUTO4

45 AUTO5 AUTO5

46 AUTO6 AUTO6

47 AUTO7 AUTO7

48 AUTO8 AUTO8

49 AUTO9 AUTO9

50 AUTO10 AUTO10

51 CASH2 CA2

52 CHECK CHK

53 CHECK2 CHK2

54 CH1 CH1

55 CH2 CH2

56 CH3 CH3

57 CH4 CH4

58 CH5 CH5

59 CONV1 CONV1

Key No. KEY KEY TEXT

60 CONV2 CONV2

61 CONV3 CONV3

62 CONV4 CONV4

63 FS TEND FSTEND

64 RA RA

65 RA2 RA2

66 PO PO

67 PO2 PO2

68 CASHIER NO. CASH#

69 BIRTHDAY BIRTH

999 INHIBIT

ER-A440 KEY POSITION

[JOB#971]SRV FILE PROGRAMMING. (File creation deletion and change ofrecord count or block count)

Key operation

• Normal file

GroupNo.

File name Type File table No.

(Create/Erase) 1 Dept. 1 1, 2, 4, 6 2 Dept Text (8chra.) 0 3 3 Dept Text (12chra.) 0 4 4 Department Text (16chra.) 0 5 5 PLU 1 8, 9, 11, 13 6 PLU Text (8chra.) 0 10 7 PLU Text (12chra.) 0 11 8 PLU Text (16chra.) 0 12 9 Link PLU 1 1610 Cashier 1 19, 20, 21, 22, 2311 Hourly 1 27, 2812 Daily net 1 29, 3013 Reg. buffer 1 3114 Term Dept. 0 715 Term PLU 0 1416 Term Transaction 0 1817 Term Cashier transaction 0 2418 All of term files 0 7, 14, 18, 24

Type = 0 ; Create/Erase only

Type = 1 ; Create/Erase and Increase/decrease the number ofRecords or blocks.

: The files which are created or erased by the entry of groupNo.

04 08 12 16 20 24 28 32 36 42 48 54 60 66

03 07 11 15 19 23 27 31 35 41 47 53 59 65

02 06 10 14 18 22 26 30 34 40 46 52 58 64

01 05 09 13 17 21 25 29 34 39 45 51 57 63

43 49 55 61 67

44 50 56 62 68

37

38

R J

:FIXED KEY (NO TO CHANGE)

971 @/FOR abcFile group No.

@/FOR

delete

CA/ATXXXXXNumber of records

– 13 –

File table (In the ER-A610, the shaded section ( ) of the FUNCTION KEY LIST is not used.)

TableNo.

File nameRECORD BLOCK Label

sizeDatasizeMRS Max. #1 MRS Max. #2

1 Dept. Preset 20 50 1 1 1 6

2 Price 20 50 (1) 1 1 0 3

3 Text (8chra.) 0 50 (1) 0 1 0 8

4 Text (12chara.) 25 50 (1) 1 1 0 12

5 Text (16chara.) 0 50 (1) 0 1 0 16

6 Daily 20 50 (1) 1 1 0 9

7 Term 20 50 (1) 1 1 0 9

8 PLU Preset 950 1 1 5 6

9 Price 950 (8) 1 1 0 3

10 Text (8chra.) 0 (8) 0 1 0 8

11 Text (12chra.) 950 (8) 1 1 0 12

12 Text (16chra.) 0 (8) 0 1 0 16

13 Daily 950 (8) 1 1 0 9

14 Term 0 (8) 0 1 0 9

15 Link PLU 50 1 1 3 15

16 Transaction Label 83 83 1 1 2 0

17 Daily 83 83 (16) 1 1 0 8

18 Term 83 83 (16) 1 1 0 8

19 Cashier Preset 4 99 1 1 1 3

20 Flag 4 99 (19) 1 1 0 2

21 Text 4 99 (19) 1 1 0 8

22 Cashier transaction Label 42 42 4 99 (19) 2 0

23 Daily 42 42 (22) 4 99 (19) 0 8

24 Term 42 42 (22) 4 99 (19) 0 8

25 Total cashier (Buffer) Label 42 42 1 1 2 0

26 Total 42 42 (25) 1 1 0 8

27 Hourly Label 48 48 1 1 1 0

28 Daily 48 48 (27) 1 1 0 8

29 Daily net Label 36 36 1 1 3 0

30 Total 36 36 (29) 1 1 0 8

31 Reg. buffer 80 255 1 1 0 36

(#1) : Same as the number of record of table no. N

(#2) : Same as the number of block of table no. N

[JOB#996, 998] RAM DATA BACKUP function(ECR↔ECR, ECR↔ER-02FD)

[JOB#996] RAM data send

X : SSP = 0Standard RAM (64KB) = 1Optional RAM: ER-03RA (512KB) = 2

[JOB#998] RAM data receive

996 X@/FOR

All data

CA/AT

SBTL

Send to ECR or ER-02FD(Baud rate setting:#903-A)Send to ECR(Auto baud rate setting)

998 @/FOR CA/AT

SBTL

Receive from ECR or ER-02FD(Baud rate setting:#903-A)Receive from ECR(Auto baud rate setting)

– 14 –

CHAPTER 2. PROGRAM(PGM2/PGM1) MODE

1.Reading of the PGM mode program

[JOB#1100]: DEPT readingKey operation

1100 XXStart No.

@/FOR CA/ATXXEnd No.

Single item

@/FOR

All

Header logo

Data/ Time


JOB#

Dept. code/ Taxable/PriceText/ Group No.

Programming JOB#2110/ Age limitation/ HALO

Dept. code/ Sign/ Price

Range

– 15 –

[JOB#1200]: PLU readingKey operation

1200 XXXXStart No.

@/FOR CA/ATEnd No.

Single item

@/FOR XXXX

All

Header logo

Data/ Time


JOB#

Range

PLU code/ Associated Dept.code/ Base Q'tyTaxable/ PriceText

Programming: JOB#2210/Age limitation

Sign/ Price

PLU code/ Associated Dept.code/Type: L=Link PLU,(space)=Normal PLU/ Base Q'ty

– 16 –

[JOB#1300]: FUNCTION PRESET READINGKey operation

1300 @/FOR CA/AT

Header logo

Data/ Time


JOB#

Function No./ Text

Type: S=Subtotal, I=Item/Sign/ Amount

HALO

Type: S=Subtotal, I=Item/Sign/Rate

HALO

HALO

Function No./ Text/ HALO

Programming: JOB#2326/Programming: JOB#2320

Rate

Sentinel

Function No./ Text/ HALO



– 17 –

[JOB#2600]: READING OF OTHERKey operation

[JOB#2900]: AUTO KEY READINGKey operation

2600 @/FOR CA/AT

Header logo

Data/ Time


JOB#

Programming: JOB#2615Programming: JOB#2616



Programming: JOB#2631




2900 @/FOR CA/AT

Header logo

Data/ Time


JOB#

Auto key No.

Not programmed


– 18 –

[JOB#1500]: CASHIER READING REP.Key operation

[JOB#2700]: TAX TABLE READING REP.Key operation

[JOB#2119]: DIRECT KEY READING REP.Key operation

[JOB#2220]: Key operation

1500 @/FOR CA/AT

Header logo

Data/ Time


JOB#

Cashier No./ Cashier code

Cashier name/ Drawer No.

2700 @/FOR CA/AT

Header logo

Data/ Time


JOB#

Tax No./ Not programed

Rate

Lower tax Iimitation

2119 @/FOR CA/AT

Header logo

Data/ Time


JOB#

Key No./ Dept code orPLU code

Inhibit

2220 @/FOR CA/AT

Header logo

Data/ Time


JOB#

PLU code/ PLU code(MAX 5)

– 19 –

2. Programming

[JOB#1110]PROGRAMMING OF DEPT. PRICE

XX: DEPT-CODE = 01 ∼ 50

YYYYYY: PRICE = 0 ∼ 999999

Preset price is max. 6 digits.

If a price is set for a department which amount entry type is "INHIBIT"or "OPEN", its amount entry type is set as below automatically.

"PRESET" ← "INHIBIT"

"OPEN&PRESET" ← "OPEN"

MRS = 000000

[JOB#2110]PROGRAMMING OF DEPT. FUNCTION

XX: DEPT. code = 01 ∼ 50XXA: Not used (Fixed at "0")

XXB: Item validation printing 2110-B

Non compulsory 0

Compulsory 1

XXC, D: Not used (Fixed at "00")

XXE: SICS Function E

Normal 0

Single item cash sale 1

Single item finalize 2

XXF: Dept. type F

Normal 0

HASH 1

Bottle Return 2

XXG: Amount entry type G

Inhibited 0

Open 1

Preset 2

Open and preset 3

MRS = 0000001

[JOB#2111]DEPT. TAX STATUS AND SIGN PROGRAMMING

XX: DEPT. CODE = 01 ∼ 50

A: Sign A

+ 0

– 1

B: Food stamp B

Non-food stampable 0

Food stampable 1

C: Taxable 4 C

Non taxable 0

Taxable 1

D: Taxable 3 D

Non taxable 0

Taxable 1

E: Taxable 2 E

Non taxable 0

Taxable 1

F: Taxable 1 F

Non taxable 0

Taxable 1

MRS = 000000

[JOB#2112]DEPT. HALO (limit) preset

XX: DEPT. CODE = 01 ∼ 50A: Mantissa (HALO) = 1 ∼ 9B: Exponent (HALO) = 0 ∼ 7

Items A and B indicate A × 10B. Any amount below that value isenable within 9999999.

MRS = 17

SBTL@/FOR @/FOR

No change

For the next code

(Show Current code & Code entry)

1110 YYYYYY

CL

priceCA/ATXX

SBTL@/FOR @/FOR

For next code

No change


2110 ABCDEFG

CL

CA/ATXX

SBTL@/FOR @/FOR

DEPT. CODE

For the next DEPT.

No change


2111

CL

CA/ATABCDEFXX

SBTL@/FOR @/FOR CA/ATXX

DEPT. CODE

For the next DEPT.

No change


2112 AB

CL

– 20 –

[JOB#2114]DEPT. TEXT PROGRAMMING

XXX: DEPT. CODE = 01 ∼ 50

Characters can be entered by using alphabetic keys or numeric keys.

Please refer to section 4.

MRS = DPT. XX

[JOB#2116]PROGRAMMING OF DEPT. GROUP

XX: DEPT. code = 01 ∼ 50AA: Group No. = 0 ~ 9

MRS = 0

[JOB#2119]LINK NUMBER PROGRAMMING FOR DIRECT DEPT. KEYS

DEPT. code is assigned to the key no. Which has been programmedin JOB#951 programming.

XXX: Key No. = 001 ∼ 068 AB: DEPT, CODE = 01 ∼ 50

[JOB#2180]DEPARTMENT LOWER LIMITATION AGE PROGRAMMING

XX: Department code = 01 ∼ 50 YY: Age: (00 ∼ 99), 00 = No Limitation

MRS = 0

[JOB#1200]Creating/assigning PLUs and the associated departments.

XXXXXX: PLU code = 01 ∼ 999999AB: DEPT. code = 01 ∼ 50

If the record of entered PLU code is not in PLU file at this program-ming, it will be created in PLU file.

MRS = 01

[JOB#1210]PRICE PROGRAMMING FOR PLUS

XXXXXX: PLU CODE = 1 ∼ 999999

YYYYYY: Amount = 0 ∼ 999999


If an amount is set for a PLU which amount entry type is "INHIBIT" or"OPEN", its amount entry type is set as below automatically.

"PRESET" ← "INHIBIT""OPEN" ← "OPEN" (Not change)

MRS = 000000

[JOB#1211]PLU BASE Q’TY PROGRAMMING

XXXXXX: PLU code = 1 ∼ 999999ZZ: Base quantity = 00 ∼ 99


2114

CL

All space

Character keyXX

DEPT. CODE

For the next DEPT.


@/FOR @/FOR SBTL CA/AT


DEPT. CODE

Next code

No change


2116 A

CL

SBTL@/FOR @/FOR CA/ATXXX

KEY No.

Next DEPT.

ABDEPT. code

inhibit

2119


No change

For the next code


YY2180

CL

SBTL@/FOR @/FOR CA/AT

PLU code

No change


ABXXXXXX

CL

1200


PLU CODE

For next code

No change


YYYYYYXXXXXX

CL

1210

SBTLZZ@/FOR @/FOR CA/ATXXXXXX

PLU CODE

For the next PLU

No change

(Show Current code & Code entry)CL

1211

– 21 –

[JOB#2210]PLU function programming

XXXXXX:

PLU code = 1~999999A, B: Not used (Fixed at "00")

C: Amount entry type C

Inhibited 0

Open 1

Preset 2

Open and preset 3

Delete 4


MRS = 002

[JOB#2211]PLU TAX STATUS PROGRAMMING

XXXXXX: PLU code = 1 ∼ 999999

A: Sign A

+ 0

– 1

B: Food stamp B

Non stampable 0

Stampable 1

C: Taxable 4 C

Non taxable 0

Taxable 1

D: Taxable 3 D

Non taxable 0

Taxable 1

E: Taxable 2 E

Non taxable 0

Taxable 1

F: Taxable 1 F

Non taxable 0

Taxable 1


MRS = 000000

[JOB#2214]PLU TEXT PROGRAMMING

XXXXXX: PLU CODE = 1 ∼ 999999

Characters can be entered by using alphabetic keys or numeric keys.

Please refer to section 4.

MRS = PLXXXXXX

[JOB#2219]PLU CODE DEFINITION FOR DIRECT PLU KEYS

XXX: Key No. = 001 ~ 068YYYYYY: PLU code = 1~999999

PLU code is assigned to the key No. which has been programmed inJOB#951 programming.

[JOB#2220]LINKED PLU PROGRAMMING

XXXXXX: PLU code = 1 ∼ 999999YYYYYY: PLU code = 1 ∼ 999999

When the "SBTL" key is depressed without entering any number in(YYYYYY), there is no link.

PLU code should already be defined when they are used in program-ming here.

MRS = 0

[JOB#2280]PLU LOWER LIMITATION AGE PROGRAMMING

XXXXXX: PLU code = 01 ∼ 999999YY: Age = 00 ∼ 99, 00 = No Limitation

MRS = 0



No change

PLU code

For next code


ABCXXXXXX

CL

2210

SBTLABCDEF@/FOR @/FOR CA/ATXXXXXX

No change

For the next PLU

PLU code

CL

(Show current code & code entry)

2211

SBTLCharacter key@/FOR @/FOR CA/ATXXXXXX

For the next PLU

PLU code

All space

CL(Show Current code & Code entry)

2214


Next code

Key No.

inhibit

PLU code2219 XXX YYYYYY

SBTL2220 YYYYYY@/FOR @/FOR CA/ATXXXXXX

Max. 5 times

0

PLU CODE


No change

For the next code


XXXXXX YY2280

CL

– 22 –

[JOB#2230]PLU CODE PROGRAMMING (range)

XXXXXX: Start PLU code = 1 ∼ 999999YYYYYY: End PLU code = 1 ∼ 999999

AB: Dept. code = 1~50

All are set with the contents of Start PLU setting.

[JOB#2231]PLU function programming (RANGE)


XXXXXX: Start PLU code = 1~999999YYYYYY: End PLU code = 1~999999

A, B: Not used (Fixed at "00")

C: Amount entry type C

Inhibited 0

Open 1

Preset 2

Open and preset 3

Delete 4

MRS = 000

[JOB#2232]PLU TAX STATUS PROGRAMMING (RANGE)


XXXXXX: Start PLU code = 1 ∼ 999999YYYYYY: End PLU code = 1 ∼ 999999

A: Sign A

+ 0

– 1

B: Food stampable B


Food stampable 1

C: Taxable 4 C

Non taxable 0

Taxable 1

D: Taxable 3 D

Non taxable 0

Taxable 1

E: Taxable 2 E

Non taxable 0

Taxable 1

F: Taxable 1 F

Non taxable 0

Taxable 1

[JOB#1310]RATE PROGRAMMING

XXX: Fanction No.YYYY. YYYY: Rate

FunctionNo.

Function Entry range Remarks

1 (–)1

0 to 999999 (–) unit price 2 (–)2

3 (–)3

4 (–)4

5 %1

0 to 100.00 % rate 6 %2

7 %3

8 %4

65 Conversion 10 to 9999.9999 Rate 66 Conversion 2

67 Conversion 3

MRS = 0

[JOB#2311]MISC KEY PROGRAMMING 1

XXX: Function No.

Function No. Function

1 (–)1

2 (–)2

3 (–)3

4 (–)4

5 %1

6 %2

7 %3

8 %4

2230 YYYYYY@/FOR @/FORXXXXXX

PLU CODE

@/FOR

SBTLAB CA/AT

No change ∗

PLU CODE

2231 YYYYYY@/FOR @/FORXXXXXXPLU CODE

SBTLABC CA/AT

@/FOR

No change ∗

2232 YYYYYY@/FOR @/FORXXXXXX

PLU CODE

SBTLABCDEF CA/AT

@/FOR

No change ∗

SBTL1310 YYYY.YYYY@/FOR @/FOR CA/ATXXX

Function No. Rate

No change

SBTL2311 ABCDEF@/FOR @/FOR CA/ATXXX

Function No.

No change

– 23 –

A: Sign A

+ 0

– 1

B: Food stamp B

Non food stampable 0

Food stampable 1

C: Taxable 4 C

Non taxable 0

Taxable 1

D: Taxable 3 D

Non taxable 0

Taxable 1

E: Taxable 2 E

Non taxable 0

Taxable 1

F: Taxable 1 F

Non taxable 0

Taxable 1

MRS = 100000

[JOB#2312, 2322]HALO PROGRAMMING

XXX: Function No.A: Mantissa (0 to 9)B: Exponent (0 to 7) for (–) and Tax

Exponent (0 to 8) for RA/PO and each media

JOB#Function

No.Function Remarks

2312

1 (–)1

Item B is specificablewithin the range from 0 to7.

2 (–)2

3 (–)3

4 (–)4

32 TAX

58 RAItem B is specificablewithin the range from 0 to8.

59 RA2

60 PO

61 PO2

2322

55 CA1

Item B is specificablewithin the range from 0 to8.

56 CA2

80 CHK

81 CHK2

70 CH1

72 CH2

74 CH3

76 CH4

78 CH5

Entry range, system: A × 10B

MRS = 17 ((–)1~(–)4, TAX)18 (RA, RA2, PO, PO2, CA1, CA2, CHK, CHK2, CH1~CH5)

[JOB#2313]MISCELLANEOUS KEY PROGRAMMING (% HALO)

XXX: Function No.YYY. YY: % HALO

FunctionNo.

Function Remarks

5 %1

6 %2

7 %3

8 %4

[JOB#2314]TEXT PROGRAMMING FOR MISC KEYS

XXX: FUNCTION NO.

Characters can be entered by using character keys or numeric keys.the key entery sequence for entering one character by numeric keysis as follows:

XXX → 00 key XXX: CHARACTER CODE (3DIGITS)

Please refer to section 4

F-NO. FUNCTION DEFAULT TEXT 1 (–)1

2 (–)2

3 (–)3

4 (–)4

5 %1

6 %2

7 %3

8 %4

9 NET1

10 TAXABLE1 ST

11 GROSS TAX1

12 REFUND TAX1

13 NET TAX1

14 EXEMPT TAX1

15 TAXABLE2 ST

16 GROSS TAX2

17 REFUND TAX2

18 NET TAX2

19 EXEMPT TAX2

20 TAXABLE3 ST

21 GROSS TAX3

22 REFUND TAX3

23 NET TAX3

24 EXEMPT TAX3

25 TAXABLE4 ST

26 GROSS TAX4

27 REFUND TAX4

28 NET TAX4

SBTL23122322

AB@/FOR @/FOR CA/ATXXXFunction code

No change

SBTL2313 YYY.YY@/FOR @/FOR CA/ATXXX

No change

SBTL2314 @/FOR @/FOR CA/AT

Function number Max. 8 char.

All space

XXX Character key

– 24 –

F-NO. FUNCTION DEFAULT TEXT29 EXEMPT TAX4

30 GROSS M-TAX

31 REFUND M-TAX

32 NET M-TAX

33 NON GST SUBTOTAL

34 PST TOTAL (For "A" version)

35 GST TOTAL (For "A" version)

36 FS1 FORGIVE

37 FS2 FORGIVE

38 FS3 FORGIVE

39 TOTAL TAX

40 NET

41 NET2

42 COUPON PLU

43 ITEM VOID

44 SBTL VOID

45 MANAGER VOID

46 VOID MODE

47 REFUND

48 HASH VOID

49 HASH REFUND

50 NO SALE

51 VP COUNTER

52 DRAWER COUNTER

53 CUSTOMER

54 NET3 (SALES)

55 CASH

56 CASH2

57 FS SALE

58 RA

59 RA2

60 PO

61 PO2

62 CHECK CASHING

63 CHECK CHANGE

64 FS CHANGE

65 CONVERSION1

66 CONVERSION2

67 CONVERSION3

68 CONVERSION4

69 FS IN DRAWER

70 GROSS CHARGE1

71 REFUND CHARGE1

72 GROSS CHARGE2

73 REFUND CHARGE2

74 GROSS CHARGE3

75 REFUND CHARGE3

76 GROSS CHARGE4

77 REFUND CHARGE4

78 GROSS CHARGE5

79 REFUND CHARGE5

80 CHECK

81 CHECK2

82 CASH+CHECK IN DRAWER

83 CASH IN DRAWER

84VAT EXEMPT (For DOUGHNUTTAX Type1) (For "A" version)

85 AVERAGE (HOURLY REPORT)

F-NO. FUNCTION DEFAULT TEXT86 GROUP1

87 GROUP2

88 GROUP3

89 GROUP4

90 GROUP5

91 GROUP6

92 GROUP7

93 GROUP8

94 GROUP9

95 (+)DEPT TOTAL

96 (–)DEPT TOTAL

97 HASH (+)DPT TOTAL

98 HASH (–)DPT TOTAL

99 BOTTLE (+)DPT TOTAL

100 BOTTLE (–)DPT TOTAL

101 SUBTOTAL

102 MDS SBTL

103 TOTAL

104 CHANGE

105 FS SBTL

106 FS TEND

107 FS CHANGE

108 ITEMS

109 COPY RCPT TITLE

110 DEPT REPORT TITLE

111 GROUP REPORT TITLE

112 PLU REPORT TITLE

113 CATEGORY REPORT TITLE

114 TRANSACTION REPORT TITLE

115 CID REPORT TITLE

116 CASHIER REPORT TITLE

117 HOURLY REPORT TITLE

118 DAILY NET REPORT TITLE

119 ZERO SALES REPORT TITLE

[JOB#2315]MISC KEY PROGRAMMING (%)

XXX: Function No.

A: % type A

Subtotal % 0

Item % 1

Function No. Function Remarks

5 %1

6 %2

7 %3

8 %4

MRS = 0

[JOB#2316]

SBTL2315 A@/FOR @/FOR CA/ATXXX

No change

– 25 –

MISC KEY PROGRAMMING ( )

XXX: Function No.

A: type A

Subtotal $ 0

Item 1

Function No. Function Remarks

1 (—) 1

2 (—) 2

3 (—) 3

4 (—) 4

MRS = 0

[JOB#2320]MEDIA KEY PROGRAMMING

XXX: Function No.

Function No. Function A B C D E F G

55 CA 1

56 CA 2

70 CH 1

72 CH 2

74 CH 3

76 CH 4

78 CH 5

80 CHK

81 CHK2

Items marked with on ( ) are programmable.

A: CAT 1 A

Non compulsory 0

Compulsory 1

B: Footer print on receipt B

No 0

Yes 1

C: Non-add code entry C

Non compulsory 0

Compulsory 1

D: Change due D

Enable 0

Disable 1

E: VP E

Non compulsory 0

Compulsory 1

F: Drawer opening F

Yes 0

No 1

G: Entry of amount tended G

Non compulsory (Cash, Check)Inhibit (CH1 to CH5)

0

Compulsory 1

MRS=0000000

[JOB#2321]MEDIA KEY FUNCTION PROGRAM (AMOUNT HALO)

XXX: Function No.YYYYYYYYY: Limitation amount

Func. No.

Function Entry range MRS

836362

CID (Sentinel)CHK CHANGECA/CHK

0 to 9999999.990 to 999999.990 to 999999.99

9999999.99 999999.99 999999.99

[JOB#2326]MEDIA KEY PROGRAMMING – 2

XXX: Function No.

Function No. Function

55 CA 1

56 CA 2

70 CH 1

72 CH 2

74 CH 3

76 CH 4

78 CH 5

80 CHK

81 CHK2

A: Taxable 4 delete A

No 0

Yes 1

B: Taxable 3 delete B

No 0

Yes 1

C: Taxable 2 delete C

No 0

Yes 1

D: Taxable 1 delete D

No 0

Yes 1

MRS=0000

SBTL2316 A@/FOR @/FOR CA/ATXXX

No change

SBTL2320 ABCDEFG@/FOR @/FOR CA/ATXXX

No change

SBTL2321 YYYYYYYY@/FOR @/FOR CA/ATXXX

No change


No change

ABCD2326 XXX

– 26 –

[JOB#1500]CASHIER CODE DIFINITION

XXX: Cashier No.= 1 ∼ 99YYYY: Cashier code = 00 ∼ 99

MRS = Same code as cashier No.

[JOB#1514]CASHIER NAME PROGRAMMING

YYYY: Server code = 01 ∼ 99

Characters can be entered by using character keys or numeric keys.The key entry sequence for entering one character by numeric keysis as follows:

XXX → 00 KEY XXX: Character code (3 digits)

Please refer to section 4.Max. 8 charactersMrs = ’Space’

[JOB#2510]CASHIER PROGRAMMING

YYYY: Cashier code = 01~99

A: Drawer No. H

Not open 0

Drawer No. 1~2

MRS = 1

[JOB#2610]DATE SETTING

XXYYZZ: Date (Year-Month-Day/Day-Month-Year/Month-Day-Year)

The date entry format complies with the applicable SRV-modeprogramming.

MRS = 010100

[JOB#2611]TIME SETTING

XX: Hour (00 ∼ 23)YY: Minute (00 ∼ 59)

MRS = 0

[JOB#2612]MACHINE NUMBER SETTING

XXXXXX: Machine number (0 ∼ 999999)

MRS = 0

[JOB#2613]CONSECUTIVE NUMBER SETTING

XXXX: Consecutive number (0000 ∼ 9999)

MRS = 0000

[JOB#2614]LOGO TEXT PROGRAMMING

X: 1 ∼ 6 1 (24 char.)

2 (24 char.)

3 (24 char.)

4 (24 char.)

5 (24 char.)

6 (24 char.)

Character can be entered by using character keys or numeric keys.

The key entry sequence for entering one character by numeric keysis as follows:

XXX → 00 Key XXX: Character code (3 digits)Please refer to section 4.

MRS =

NOTE: This programming is related to JOB# 912D programming."6-line header": All 6 lines are programmable."3-line header": Upper 3 lines (1st-3rd line) are programma-

ble."3-line footer": Lower 3 lines (4th-6th line) are programma-

ble."3-line header and 3-line footer": All 6 lines are programma-

ble. (1st-3rd: Header, 4th-6th: Footer)

[JOB#2615]Programming of the limits to No. of times of validation printing.

Y: No. of times of validation printing = 0 ∼ 9 X: Not used (Fixed at "0")

MRS = 10

SBTL1500 YY@/FOR @/FOR CA/ATXX

No change

SBTL1514 @/FOR @/FOR CA/AT

All space

YY Character key

SBTL2510 A@/FOR @/FOR CA/ATYY

No change

2610 @/FOR CA/ATXXYYZZ

0

2611 @/FOR CA/ATXXYY

0

2612 @/FOR CA/ATXXXXXX

0

2613 @/FOR CA/ATXXXX

2614 Character key@/FOR @/FOR SBTL CA/ATX

Position code

All space

2615 @/FOR CA/ATYX

0

– 27 –

[JOB#2616]OPTIONAL FEATURE

XX: 1 MRS = 00000000

A: OP X/Z report A

Enable 0

Disable 1

B: PO operation in REG mode B

Enable 0

Disable 1

C: Refund type of sale function in REGmode

C

Enable 0

Disable 1

D: "RFND" key entry in REG mode D

Enable 0

Disable 1

E: Direct void function in REG mode E

Enable 0

Disable 1

F: In direct void in REG mode F

Enable 0

Disable 1

G: Subtotal void in REG mode G

Enable 0

Disable 1

H: Refund VP H

Non compulsory 0

Compulsory 1

XX: 2 MRS = 00000000

A: The first last item void A

Enable 0

Disable 1

B, C: Not used (Fixed at "00")

D: Printing of the number of purchases D

No 0

Yes 1

E: Time print E

Yes 0

No 1

F: Printing of journal F

Full print 0

Journal select 1

G: Item VP G

Enable 0

Disable 1

H: (–) VP H

Non compulsory 0

Compulsory 1

X: 3 MRS = 00000000A, B: Not used (Fixed at "00")

C: Zero skip in Cashier report C

Yes 0

No 1

D: Zero skip in Transaction report D

Yes 0

No 1

E: Zero skip in Dept. report E

Yes 0

No 1

F: Zero skip in PLU report F

Yes 0

No 1

G: Zero skip in Hourly report G

Yes 0

No 1

H: Zero skip in Daily net report H

Yes 0

No 1

X: 4 NOT USED MRS = 00000000X: 5 NOT USED MRS = 00000000X: 6 NOT USED MRS = 00000000X: 7 MRS = 00000000


C: No sale in REG mode C

Enable 0

Disable 1

D: Finalization in REG mode whenSBTL is zero

D

Enable 0

Disable 1

E, F, G, H: Not used (Fixed at "0000")

@/FOR @/FOR SBTL CA/ATXX

No change

ABCDEFGH2616

– 28 –

X: 8 MRS = 00000000A, B, C, D: Not used (Fixed at "0000")

E: Validation printing of check cashing E

Non compulsory 0

Compulsory 1

F: Validation printing of RA F

Non compulsory 0

Compulsory 1

G: Validation printing of PO G

Non compulsory 0

Compulsory 1

H: Not used (Fixed at "0")X: 9 MRS = 00000000


C: BIRTHDAY print on printer C

Yes 0

No 1

D, E, F, G, H: Not used (Fixed at "00000")X: 10 NOT USED MRS = 00000000X: 11 NOT USED MRS = 00000000X: 12 NOT USED MRS = 00000000X: 13 NOT USED MRS = 00000000

[JOB#2617]PROGRAMMING OF THE TIME INTERVAL FOR THE TILL TIMER

XXX: 0 ∼ 255 sec

MRS = 000

[JOB#2619]HOURLY REPORT (Starting time)

a: Memory type A

30 minuts (24 hour) 0

60 minuts (24 hour) 1

bb: Starting time (hour): 00 ∼ 23

ex)

Case 1.

X1 Hourly report (#160) (30 min, start time = 7]

2617 @/FOR CA/ATXXX

0

2619 @/FOR CA/ATabb

0

2619 @/FOR CA/AT007

24 hours started from 7:00

– 29 –

[JOB#2620]STACK REPORT

XX: JOB#SSSSSS: Start codeEEEEEE: End code

JOB# REPORT NAME TYPE00 General10 DEPT.13 DEPT. All group20 PLU RANGE27 PLU zero sales RANGE29 PLU category RANGE30 Transaction31 CID50 All cashier60 Hourly RANGE (only X report)60 Hourly ALL70 Daily net

[ ]

Max. 70 step are programmable. "1 step" means the memory sizeused for one no range type JOB#.

The RANGE type JOB# means "8 steps".

For example)

The memory size for programming JOB#00, 20 and 50 is 10 steps.(ie. 1 step for JOB#00, 8 step for JOB#20, and 1 step for JOB#50. )

[JOB#2630, 2631, 2632]SECRET CODE PROGRAMMING

#2630: PGM1 mode

#2631: X1/Z1 mode

#2632: X2/Z2 mode

XXXX: Secret code = 0000 ~ 9999

If "0" is entered, "compulsory secret code entry" is canceled.

MRS = 0

[JOB#2690]THE ASSIGNMENT OF RS232 FUNCTION BY EACH DEVICES

X: 1 MRS = 0000

A: On-line ANo 0Yes (Channel #8) 8

B: Print data sending BNo 0Yes (Channel #8) 8

C, D: Not used (Fixed at "00")X: 2 MRS = 0000


C CAT CNo 0Yes (Channel #8) 8


X: 3 NOT USED MRS = 0000

[Job# 2710]TAX TABLE PROGRAMMING

72 BREAKPOINTS CAN BE PROGRAMMED FOR EACH TAX-TABLE.

(Case of interval between break point is 1 dollar or more and lessthan 100 dollar, 36 breakpoints is programmed for each table.)

DEPRESSION OF THE SBTL KEY AT THE FOLLOWING POINTSMEANS A TAX TABLE DELETE OPERATION.

A: INTERVAL BETWEEN BREAKPOINTS IS = 11 DOLLAR OR MORE AND LESS THAN 100 DOLLAR

INTERVAL BETWEEN BREAKPOINTS IS = 0BELOW 1 DOLLAR

B: TABLE 1 PROGRAMMING = 1TABLE 2 PROGRAMMING = 2TABLE 3 PROGRAMMING = 3TABLE 4 PROGRAMMING = 4

TAX RATE : 0.0000 ~ 99.9999CYCLE : 0 ~ 9999INITIAL TAX : 0 ~ 999LOWER TAX LIMIT : 0 ~ 99999BREAK POINT : 0 ~ 99999

MRS = NO TAX

[JOB#2711]TAX RATE PROGRAMMING

DEPRESSION OF THE ST KEY AT FOLLOWING POINTS PER-FORM A TAX TABLE DELETE OPERATION.

A: Tax programming ATax1 1Tax2 2Tax3 3Tax4 4

xxx.xxxx: % TAX rate = 0.0000~999.9999%

LOWER TAX LIMITATION = 0.00 to 999.99

(This is invalid in VAT system.)

MRS = 0

2620 @/FOR

XX @/FOR SSSSSS @/FOR EEEEEE

All delete

No range

Next JOB# (max.=20)

SBTL CA/AT

2630 @/FOR CA/ATXXXX

0

26312632

2690 ABCD@/FOR @/FOR SBTL CA/ATX

0

2711 XXX.XXXX@/FOR @/FORA

Declaration of TAX TAX rate

XXXXX CA/AT

Lower tax limitfor add tax.

@/FOR

CA/AT

When lower taxlimit is 0.

✽

0

– 30 –

[JOB#2900]

<CAUTION>(This JOB must be performed at X2/Z2 mode position.)

AUTO KEY SETTING

(Auto key function)

• This machine has [AUTO] key which can be programmed by thefollowing key-sequence.

• When [AUTO] key is depressed, the machine works the same asthe programmed key-sequence programed.

<Example>

Mode switch

⇓

(X2/Z2)

(REG)

(X2/Z2)

(REG)

[JOB#2910, 2911]Training mode start (#2910), End (#2911)

<Training mode>

All operation is same as REG-mode operation.In the training mode, the concective number is printed as same num-ber m receipt/journal printer and slip printer.In the training mode, the concective number is counted up.

3. Programming by direct key entry

1) PRICE PROGRAMMING for DEPT.

XXXXXX: UNIT PRICE (Max. 6 digits)

MRS = 0

If [DPTn] (same as displayed department number) is depressed,programming mode is changed from "PRICE PROGRAMMING" to"FUNCTION PROGRAMMING" (from "FUNCTION PROGRAM-MING" to "PRICE PROGRAMMING").

2) FUNCTION PROGRAMMING for DEPT.

A: Sign A

+ 0

– 1

B: Food stamp B


Food stampable 1

C: Taxable4 C

Non taxable 0

Taxable 1

D: Taxable3 D

Non taxable 0

Taxable 1

E: Taxable2 E

Non taxable 0

Taxable 1

F: Taxable1 F

Non taxable 0

Taxable 1

G: SICS Function G

Normal 0

Single item cash sale 1

Single item finalize 2

H: Limitation (Mantissa) = 0~9

I: Limitation (Exponebt) = 0~7

MRS = NORMAL, 17 HALO

If [DPTn] (same as displayed department number) is depressed,programming mode is changed from "PRICE PROGRAMMING"to "FUNCTION PROGRAMMING" (from "FUNCTION PRO-GRAMMING" to "PRICE PROGRAMMING").

Double depression of [DPTn] is necessary for the first time.

2900 (Free key)AUTO

Max.25

@/FOR CA/AT

AUTO2

AUTO3

AUTO4

AUTO5

AUTO

AUTO2

AUTO3

AUTO4

AUTO5

Delete

AUTO10 AUTO10

2900 @/FOR AUTO PLU1 100 DEPT2 AUTO CA/AT

Key entry R/J Display Comment

AUTO PL000001 $1.10

PL000001 $1.00

PL0000001 same as entryPLU11.10

1

10

100

DEPT02 1.10

same as entry1

same as entry0

same as entry0

same as entryDEPT2

2900 @/FOR AUTO2 PLU1 100 DEPT2 CA/ATAUTO2

Key entry R/J Display Comment

DEPT 1 DEPT01 DEPT01 1.10

100

CHANGE 0.00

same as entry1

same as entry0

same as entry0

same as entryCA/AT

AUTO 2

$1.00

***TOTAL $1.00

CASH $1.00

CHANGE $0.00

10

1

2910/2911 @/FOR CA/AT

DEPTn

Not changed

for next code

XXXXXX CA/ATSBTL

DEPTn*

Not changed

*ABCDEFGHI CA/AT@/FOR

– 31 –

3) PRICE & MODIFY PROGRAMMING for (–) KEYS.

XXXXXX: UNIT PRICE (Max. 6 digits)

MRS = 0

If the same [(–)n] key is depressed, programming mode ischanged from "PRICE PROGRAMMING" to "FUNCTION PRO-GRAMMING" (from "FUNCTION PROGRAMMING" to "PRICEPROGRAMMING").

4) FUNCTION PROGRAMMING for (–) KEYS.

A: Sign A

+ 0

– 1

B: Food stamp B


Food stampable 1

C: Taxable4 C

Non taxable 0

Taxable 1

D: Taxable3 D

Non taxable 0

Taxable 1

E: Taxable2 E

Non taxable 0

Taxable 1

F: Taxable1 F

Non taxable 0

Taxable 1

G: Not used (Fixed at "0")

H: Limitation (Mantissa) = 0~9

I: Limitation (Exponebt) = 0~7

MRS = NORMAL, 17 HALO

If the same [(–)n] key is depressed, programming mode ischanged from "PRICE PROGRAMMING" to "FUNCTION PRO-GRAMMING" (from "FUNCTION PROGRAMMING" to "PRICEPROGRAMMING").

5) PLU PRESET PRICE SETTING

XXXXXX: PLU CODE (1 to 999999)YYYYYY: UNIT PRICE (6 digits)


MRS = 0

If the [PLU] or [PLUn] key is depressed, programming mode ischanged from "PRICE PROGRAMMING" to "ATTRIBUTE PRO-GRAMMING" and changed to "PLU ASSOCIATION PROGRAM-MING" by depressing the same key again.(Caution!!)The associated department is changed if the operater depress[DPTn] key instead of [PLUn] key by mis-operation at this timming.

6) PLU ASSOCIATION TO DEPARTMENTS

XXXXXX: PLU CODE (1 to 999999)


MRS = 01

If the [PLU] or [PLUn] key is depressed, programming mode ischanged from "PRICE PROGRAMMING" to "ATTRIBUTE PRO-GRAMMING" and changed to "PLU ASSOCIATION PROGRAM-MING" by depressing the same key again.(Caution!!)The associated department is changed if the operater depress[DPTn] key instead of [PLUn] key by mis-operation at this tim-ming.

Triple depression of [PLU] or [PLUn] key is necessary for thefirst time.

Not changed

*XXXXXX CA/ATSBTL(-)n

Not changed

ABCDEFGHI(-)n (-)n CA/AT@/FOR

Not changed

XXXXXX

PLU code

for next code

YYYYYYY CA/ATSBTLPLU

PLUn

XXXXXX

PLU code

PLU delete

PLU

PLUn

for next code

CA/ATDPTn

VOID

SBTLYY

Not changed

– 32 –

7) PROGRAMMING OF PLU/SUBDEPT

XXXXXX: PLU CODE (1 to 999999)

A: Sign A

+ 0

– 1

B: Food stamp B


Food stampable 1

C: Taxable4 C

Non taxable 0

Taxable 1

D: Taxable3 D

Non taxable 0

Taxable 1

E: Taxable2 E

Non taxable 0

Taxable 1

F: Taxable1 F

Non taxable 0

Taxable 1

G: Amount entry type G

Inhibited 0

Open 1

Preset 2

Open and preset 3

Delete 4


MRS = 002

If the [PLU] or [PLUn] key is depressed, programming mode ischanged from "PRICE PROGRAMMING" to "ATTRIBUTE PRO-GRAMMING" and changed to "PLU ASSOCIATION PROGRAM-MING" by depressing the same key again.

Double depression of [PLU] or [PLUn] key is necessary for thefirst time.

8) PROGRAMMING RATE FOR %KEY.

XXX.XX: 0.00 to 100.00

MRS = 0.00%

If the same [%n] key is depressed, programming mode is changedfrom "RATE PROGRAMMING" to "FUNCTION PROGRAMMING"(from "FUNCTION PROGRAMMING" to "PRICE PROGRAM-MING").

9) PROGRAMMING FOR %KEY.

A: Sign A

+ 0

– 1

B: Food stamp B


Food stampable 1

C: Taxable4 C

Non taxable 0

Taxable 1

D: Taxable3 D

Non taxable 0

Taxable 1

E: Taxable2 E

Non taxable 0

Taxable 1

F: Taxable1 F

Non taxable 0

Taxable 1

MRS = 100000

If the same [%n] key is depressed, programming mode is changedfrom "RATE PROGRAMMING" to "FUNCTION PROGRAMMING"(from "FUNCTION PROGRAMMING" to "PRICE PROGRAM-MING").

Not changed

XXXXXX

PLU code

for next code

ABCDEFG @/FOR CA/ATPLU

PLUn

XXX.XX

Not changed

SBTL CA/AT%n

Not changed

ABCDEFG%n %n CA/AT@/FOR

– 33 –

10) PROGRAMMING RATE FOR CONVERSION KEY

XXXX.XXXX: 0.0000 to 9999.9999MRS = 0.00000

11) PROGRAMMING FOR MEDIA KEYS &FUNCTION KEYS.

A: Mantissa (0 to 9)

B: Exponent (0 to 8)

MRS = 18 digits. (RA, PO, CASH2, CHn, CHKn)17 digits. (TAX)

12) DATA, TIME PROGRAMMING.

DATE: date entry format follows SRV Programming (6 digits)TIME: 24 hour system (4 digits)

MRS = DATA: 01/01/00TIME: 00:00

13) TAX TABLE PROGRAMMING

72 BREAKPOINTS CAN BE PROGRAMMED FOR EACH TAX-TABLE.

(Case of interval between break point is 1 dollar or more and lessthan 100 dollar, 36 breakpoints is programmed for each table.)

DEPRESSION OF THE SBTL KEY AT THE FOLLOWING POINTSMEANS A TAX TABLE DELETE OPERATION.

A: INTERVAL BETWEEN BREAKPOINTS1 DOLLAR OR MORE AND LESS THAN 100 DOLLAR = 1BELOW 1 DOLLAR = 0

B: TAX TABLE No.TABLE 4/TABLE 3/TABLE 2/TABLE 1 = 4/3/2/1

TAX RATE : 0.0000 ~ 99.9999CYCLE : 0 ~ 9999INITIAL TAX : 0 ~ 999LOWER TAX LIMIT : 0 ~ 99999BREAK POINT : 0 ~ 99999

MRS = NO TAX

CNV1

Not changed

XXX.XXX

CNV2

CNV3

CA/ATSBTL

RA

Not changed

PO

CASH2

CHn

CHKn

TAX

AB CA/AT@/FOR

TAX

XXXXXX

HHMM

DATA

TIME

#

XXXXXX@/FORAB @/FOR

Declaration of TAX TAX rate

XXX@/FORXXXX @/FOR

Initial TAXCycle

XXXXX@/FORXXXXX @/FOR

Break pointLower TAX limit

CA/AT

TAX

– 34 –

4. Character assignment method

∼∼ Using alphabetic assignment method ∼∼

@/FOR SBTLPush alphabetic

Repeat

Programming key layout

:

+

ZWRMHC

YVQLGB

XUPKFA

SNID

TOJE

?

(BS)(DC)

(Space)1 2 3

4 5 6

7 8 9

O

< >

;

-

#

@

=

?

)

%$

/

.

&

!

BACKSpace

( )< ( )<

( )

( ) ( )( )

( ) ( )- §

æ

Æ

£Pt

(Shift-2) (Shift)

ø ç

Φ

( ) : Function key

(DC) : Double character code entry key (One-shot)(Shift) : Character shift key (Stay-down)(Shift-2) : Mark key (One-shot)(BS) : Back space key

Using ten key of ECR

Note: 00 key is used to enter each 3 digit alpha code.

Examples

“ A (Shift-2) → “ A = “ is set

(DC) → “ A = A (double character code) is set

(Shift) → “ A = a (lowercase letter) is set

Once the (Shift) key is pressed, it stays down until it is pressedagain.

@/FOR 00XXX

3 digitsSBTL

Repeat

CODE TABLE FOR ALPHA DESCRIPTOR PROGRAMMING

CODE CHARACTER032033 !034 "035 #036 $037 %038 &039 ’040 (041 )042 *043 + 044 , 045 –046 .047 /048 0049 1050 2051 3052 4053 5054 6

CODE CHARACTER055 7056 8057 9058 :059 ;060 <061 =062 >063 ?064 @065 A066 B067 C068 D069 E070 F071 G072 H073 I074 J075 K076 L077 M

CODE CHARACTER078 N079 O080 P081 Q082 R083 S084 T085 U086 V087 W088 X089 Y090 Z091 Ä092 Ö093 Ü094 ^ 095 _096 ‘097 a098 b099 c100 d

CODE CHARACTER101 e102 f103 g104 h105 i106 j107 k108 l109 m110 n111 o112 p113 q114 r115 s116 t117 u118 v119 w120 x121 y122 z123 {

CODE CHARACTER124 |125 }126 β127 c128 !!129 1

130 2

131 3

132 4

133 1⁄2134 FT

135 ←136 →137138139140141 F

142 T

253 DC

DC: DOUBLE CODEFig. 7-2

– 35 –

CHAPTER 3. OP X/Z, X1/Z1,X2/Z2MODE

The following categories of reports can be printed by the ECR.

OP X/Z reports: These reports are taken by operators in order toreport their own sales data.

XI/Z1 reports: These reports are taken by the supervisor or man-ager in order to check and report daily sales totalsat that point.

X2/Z2 reports: These reports are taken by the owner or managerin order to check and report periodic (weekly ormonthly) tatals.

MGR/Flash-read: These reports are taken by the owner or managerin order to check and display daily sales totals atthat point.

To print reports, use the following key entry sequence

JOB# @/FOR CA/AT

Reading

Resetting

Range is required

MODE 1

OP X/Z X1/Z1 X2/Z2 F-read 3JOB#

DATA FORREADING

NOTEREPORT NAME X Z X1 Z1 X2 Z2 X1 4

GENERAL 00 —

DEPT/GROUP 10 —

IND. GROUP 12 GROUP No.

GROUP TOTAL 13 —

PLU BY RANGE 20 PLU CODE 2

PLU BY DEPT 21 DPT CODE

PLU ZERO SALES 27 ALL

PLU PRICE CATEGORY 29 PRICE 2

TRANSACTION 30 —

CID 31 — ALL CASHIER

ALL CASHIER 50 —

IND. CASHIER 51 —

HOURLY (ALL) 60 —

HOURLY (RANGE) 60 TIME 2

DAILY NET 70 —

STACKED REP 90 —

1 X1: Daily X report Z1: Daily Z reportX2: Periodic X report Z2: Periodic Z report

Stop of printing reports:The printing of all reports can be stopped by the following operation.

Set the mode switch to "MRG" to cancel.

Note) When the printing is stopped, the consecutive number or Zcounter don’t return to the original value.When Z reports, Memory is not reset.

1 X1: Daily X reportX2: Periodic X report

Z1: Daily Z reportZ2: Periodic Z report

2 The time interval range, PLU code range can be specified byentering the start and end numbers according to the followingprocedure. When specifying a single time interval, PLU code,the start number has only to be entered.

3 When 2 is entered in the third digit of a job code, periodic reportsare printed.

Example: Daily general report; job code 100Periodic general report; job code 200

*4 Reading display only

→ KEY → CL (Display amount) (Display initialize)

KEY DEPT = DEPTn keyCID = @/For keyDaily Net = ST key

All

Start No. End No.@/FORXXXXXX XXXXXX

– 36 –

COPYRIGHT 1998 BY SHARP CORPORATIONAll rights reserved.Printed in Japan.

No part of this publication may be reproduced,

stored in a retrieval system, or transmitted,in any form or by any means,

electronic, mechanical, photocopying, recording, or otherwise,

without prior written permission of the publisher.

SHARP CORPORATIONInformation Systems GroupQuality & Reliability Control CenterYamatokoriyama, Nara 639-1103, Japan

1998 February Printed in Japan

Documents

MODEL ER-A440 - Inland Cash Register is now Point Of ...... Turn off the AC switch. 2) Set the mode switch to (SRV ′) position. 3) Turn on the AC switch. 4) Turn to (SRV) position