Model Curriculum - National Skill Development Corporation · 2 Lead Furniture Maker- Bamboo (Option: Round Bamboo) This course encompasses 5 out of 5 Compulsory NOS (National Occupational

Model Curriculum Lead Furniture Maker-Bamboo

(Option: Round Bamboo)

SECTOR: FURNITURE & FITTINGS SUB-SECTOR: Cane and Bamboo Furniture OCCUPATION: Furniture Making REF ID: FFS/Q4102, V2.0 NSQF LEVEL: 4

ii Lead Furniture Maker- Bamboo (Option: Round Bamboo)

iii Lead Furniture Maker- Bamboo (Option: Round Bamboo)

TABLE OF CONTENTS

1. Curriculum 01

2. Trainer Prerequisites 12

3. Annexure: Assessment Criteria 13

1 Lead Furniture Maker- Bamboo (Option: Round Bamboo)

Lead Furniture Maker- Bamboo (Option: Round Bamboo)

CURRICULUM / SYLLABUS

This program is aimed at training candidates for the job of a “Lead Furniture Maker- Bamboo (Option:

Round Bamboo)”, in the “Furniture & Fittings” Sector/Industry and aims at building the following key

competencies amongst the learner.

Program Name

Lead Furniture Maker-Bamboo (Option: Round Bamboo)

Qualification Pack Name & Reference ID

FFS/Q4102, V2.0

Version No. 2.0 Version Update Date 03/12/2019

Pre-requisites to Training

Class VIII

Training Outcomes

After completing this programme, participants will be able to:

Use various hand and power tools required in production of bamboo furniture.

Interpret technical drawings and sketches of bamboo furniture.

Estimate cost for making the bamboo furniture.

Carry out cutting, trimming and joining of bamboo pieces according to the requirement.

Assemble different parts to make the final product

Check the quality of the finished product.

Maintain the work area, tools and equipment properly.

Follow health, safety and environment norms at workplace.

Work effectively with all the stakeholders for various functional activities.


This course encompasses 5 out of 5 Compulsory NOS (National Occupational Standards), 2 out of 2

Optional NOS of “Lead Furniture Maker-Bamboo (Option: Round Bamboo) - FFS/Q4102” Qualification

Pack issued by “Furniture & Fittings Skill Council”.

Sr No Module Key Learning Outcomes Equipment required

1 Introduction to the furniture and fittings industry Theory Duration (hh:mm) 08:00 Practical Duration (hh:mm) 00:00 Corresponding NOS Code Bridge Module

Discuss about the furniture and fittings industry

Discuss about the market scenario of bamboo furniture in India

Explain the role of a lead furniture maker-bamboo and its job opportunities in the industry

Discuss about the career path of a lead furniture maker-bamboo

2 Organizational context/ company/ employer Theory Duration (hh:mm) 08:00 Practical Duration (hh:mm) 00:00 Corresponding NOS Code FFS/N4103

Explain the importance of code of conducts, policies, manuals, rules and regulations followed in a typical organization

Describe organization structure and hierarchy followed in a typical organization

Describe functions of different divisions/ teams of an organization

3 Health and safety at workplace Theory Duration (hh:mm) 04:00 Practical Duration (hh:mm) 04:00 Corresponding NOS Code FFS/N8601

Explain the importance of maintaining a healthy and safe work environment

Differentiate between the potential risk, hazard and threat at the workplace

List the safety, ergonomic, physical, biological, and chemical hazards at workplace

Explain the precautionary measures to be taken to prevent different hazards

Discuss the ways of undertaking the first aid activities in case of different types of accidents

Demonstrate the use of personal protective equipment/ protective clothing

Gloves, safety shoes, safety cap/helmet, earplugs, goggles, nose mask, first aid box, apron, different types of fire extinguisher


Demonstrate how to keep correct body posture while standing, working, lifting and carrying heavy materials

List various do’s and don’ts of good housekeeping practices

Demonstrate the methods of doing basic safety checks for all machines, tools, and electrical equipment before work

Explain various safety signs/ instructions

Ensure general health and safety equipment are available at the workplace

Comply with restrictions imposed on harmful materials while working at workplace

4 Handling emergencies Theory Duration (hh:mm) 04:00 Practical Duration (hh:mm) 04:00 Corresponding NOS Code FFS/N8601

List the precautionary measures for prevention of accidents at the workplace

List various common causes and types of fires

List the common types of fire extinguishers

Demonstrate the use of fire extinguishers on different types of fires

Describe the evacuation procedures to be followed in case of an emergency, accident, fire, or a natural calamity

Demonstrate how to free a person from electrocution

Demonstrate the correct rescue techniques applied during fire hazards

Explain the importance of responding promptly and accurately to an accident situation

Gloves, safety shoes, safety cap/helmet, earplugs, goggles, nose mask, first aid box, apron, different types of fire extinguisher

5 Communication skills Theory Duration (hh:mm) 04:00 Practical Duration (hh:mm) 04:00 Corresponding NOS Code FFS/N8801

State the importance of possessing effective communication skills

Explain the importance of setting up good working relationship with others

Explain the significance of active listening, correct receiving of information and instructions

Describe the importance of seeking assistance/ clarification from supervisor/ senior

Describe the importance of discipline, ethics, and integrity for professional success

Explain the reporting protocol in case of queries on procedures, products, or any problem

Demonstrate how to communicate effectively with others


6 Team work Theory Duration (hh:mm) 04:00 Practical Duration (hh:mm) 04:00 Corresponding NOS Code FFS/N8801

Discuss the importance of coordination with colleagues to achieve work objectives

Explain the importance of sharing information with team wherever and whenever required to enhance quality and productivity at workplace

Discuss how to manage interpersonal conflict

Describe the significance of interacting politely with team members

State the importance of following dress code at workplace

Describe the importance of professional skills such as planning and organizing, problem solving, objection handling, and critical thinking

Participate in team building activities effectively

7 Understand the requirement of tools and materials Theory Duration (hh:mm) 08:00 Practical Duration (hh:mm) 20:00 Corresponding NOS Code FFS/N4103

List different species of bamboo used in furniture making

Distinguish among bamboo strips, slates, panels and culms

Identify different types of consumables, tools, machines, materials and their usage

Demonstrate methods of cleaning and maintaining tools, equipment and materials

Dado, chisel set, dropping knife, hammer, round planer/knot remover, scrapper, blow torch, vice, angle grinder, hand plane, V-shaped knife, pointed knife, mallet, wood saw, hacksaw, pliers, hand drill and bits, sand container, pencil, marker, staple gun, power saw, power drill, hand cutting machine, hand splicer, surface planer, trowel, tumbler, bamboo cross cutting machine, hand held bamboo splitter, hot air gun, edge trimmer machine, hand engraver machine, stand drill machine, stand zig saw, chalk liner, bamboo of required diameter, slats, adhesive, sand paper, nails, cane (3-4mm for binding), wood pegs, bending wire

8 Interpreting drawing and design specification Theory Duration (hh:mm) 08:00

Explain different shapes, symbols and abbreviations in the drawing of bamboo furniture

Explain the measurement units mentioned in the drawing

Demonstrate how to read and interpret the drawing


Practical Duration (hh:mm) 04:00 Corresponding NOS Code FFS/N4103

9 Calculating cost Theory Duration (hh:mm) 08:00 Practical Duration (hh:mm) 16:00 Corresponding NOS Code FFS/N4103

Discuss various factors which effect the cost of a furniture product

Calculate the cost considering furniture styles, durability, patterns, comfort, materials, accessories and labour

Calculate cost benefit ratio of the final furniture product

10 Preparing work area for bamboo furniture making Theory Duration (hh:mm) 04:00 Practical Duration (hh:mm) 12:00 Corresponding NOS Code FFS/N4103

Demonstrate how to check working condition/ shortage/ defect of the selected tools, machines and materials

Demonstrate how to check material for any splits, defects or treatment against insects, fungus and weather exposures

Discuss the importance of reporting any shortage or defect of materials/ hardware to the supervisor/ senior before commencement of work

Discuss the importance of keeping work area clutter free before commencement of work


11 Measuring, marking and cutting procured bamboo Theory Duration

Discuss the techniques of measurement and marking of bamboo materials

Demonstrate the method of marking techniques on bamboo pieces

Explain the importance of correct

Dado, chisel set, dropping knife, hammer, round planer/knot remover, scrapper, blow torch, vice, angle grinder, hand plane, V-


(hh:mm) 08:00 Practical Duration (hh:mm) 28:00 Corresponding NOS Code FFS/N4104

cutting techniques to minimise waste

Demonstrate the correct method of cutting procured bamboo safely into different sizes after doing the test run

shaped knife, pointed knife, mallet, wood saw, hacksaw, pliers, hand drill and bits, sand container, pencil, marker, staple gun, power saw, power drill, hand cutting machine, hand splicer, surface planer, trowel, tumbler, bamboo cross cutting machine, hand held bamboo splitter, hot air gun, edge trimmer machine, hand engraver machine, stand drill machine, stand zig saw, chalk liner, bamboo of required diameter, slats, adhesive, sand paper, nails, cane (3-4mm for binding), wood pegs, bending wire

12 Making bamboo furniture components Theory Duration (hh:mm) 04:00 Practical Duration (hh:mm) 28:00 Corresponding NOS Code FFS/N4104

Discuss about different components of bamboo furniture

Explain the importance of making components in sequence depending upon the type of furniture

Demonstrate the way of making furniture components


13 Assembling and joining Theory Duration (hh:mm) 04:00

Explain about various joints and their importance in bamboo furniture making

Demonstrate the method of making joints, joint pin, bamboo plug, bamboo nails and dowels for bamboo furniture

Explain about smoothening the

Dado, chisel set, dropping knife, hammer, round planer/knot remover, scrapper, blow torch, vice, angle grinder, hand plane, V-



surface, assembling and sealing the joints

Demonstrate the steps of assembling bamboo furniture components appropriately using bamboo joining techniques

shaped knife, pointed knife, mallet, wood saw, hacksaw, pliers, hand drill and bits, sand container, pencil, marker, staple gun, power saw, power drill, hand cutting machine, hand splicer, surface planer, trowel, tumbler, bamboo cross cutting machine, hand held bamboo splitter, hot air gun, edge trimmer machine, hand engraver machine, stand drill machine, stand zig saw, chalk liner, bamboo of required diameter, slats, adhesive, sand paper, nails, cane (3-4mm for binding), wood pegs, bending wire

14 Quality checking of bamboo furniture (hh:mm) 04:00 Practical Duration (hh:mm) 28:00 Corresponding NOS Code FFS/N8401

Explain the importance of quality checks of the products at intervals

Explain the ways of taking appropriate action for rectification of the faults

Explain the importance and process of communication to the supervisor/ senior when product is not as per the standard

Demonstrate the process of checking and rectifying symmetry, angles, structural strength and any irregularities in final finish of the product

COMPULSORY NOS: Total Duration Theory Duration 80:00 Practical Duration 180:00

Unique equipment required for the QP: Gloves, earplugs, goggles, nose mask, safety shoes, apron, safety cap/helmet, first aid box, fire extinguisher Steel rule, measurement tape, inside and outside calliper Dado, chisel set, dropping knife, width seizers, scissors, hammer, round planer/knot remover, scrapper, blow torch, vice, grinder, hand plane, V-shaped knife, pointed knife, mallet, wood saw, hacksaw, pliers, hand drill and bits, sand container Power saw, power drill, hand cutting machine, hand splicer, surface planer, trowel, tumbler Bamboo of required diameter, slats adhesive, sand paper, nails, cane (3-4mm for binding), wood pegs, bending wire Classroom aids: Blackboard, chalks, duster


OPTIONS (Optional to choose any or all or none)

OPTION 1: Round Bamboo

Sr No Module Key Learning Outcomes Equipment required

1 Understand the requirement of tools and materials Theory Duration (hh:mm) 02:00 Practical Duration (hh:mm) 04:00 Corresponding NOS Code FFS/N4101

List the tools, equipment and materials required for round bamboo furniture making

Demonstrate method of selection of right aged, coloured round bamboo poles suitable for furniture making

Explain traditional/ chemical treatment of bamboo poles before making furniture

Demonstrate the ways of handling and maintaining tools

Dado, chisel set, dropping knife, hammer, round planer/knot remover, scrapper, blow torch, vice, angle grinder, hand plane, V-shaped knife, pointed knife, mallet, wood saw, hacksaw, pliers, hand drill and bits, sand container, pencil, marker, staple gun, power saw, power drill, hand cutting machine, hand splicer, surface planer, trowel, tumbler, bamboo cross cutting machine, hand held bamboo splitter, hot air gun, edge trimmer machine, hand engraver machine, stand drill machine, stand zig saw, chalk liner, bamboo of required diameter, adhesive, sand paper, nails, cane (3-4mm for binding), wood pegs, bending wire

2 interpreting sketches, drawings and designs Theory Duration (hh:mm) 04:00 Practical Duration (hh:mm) 08:00 Corresponding NOS Code FFS/N4101

Explain the details of furniture drawing

Demonstrate how to read and interpret details of furniture drawing

3 Preparing cost estimates Theory Duration (hh:mm) 04:00

Discuss various factors which effect the cost of a furniture product

Calculate the cost considering furniture styles, durability, patterns, comfort, appearance, materials and labour



4 Preparing work area for furniture making Theory Duration (hh:mm) 02:00 Practical Duration (hh:mm) 04:00 Corresponding NOS Code FFS/N4101

Discuss the importance of checking working condition/ shortage/ defect in selected tools, machines and materials

Demonstrate ways of checking round bamboo for any splits, defects or treatment against insects, fungus and weather exposures

5 Measuring, marking and cutting activities Theory Duration (hh:mm) 04:00 Practical Duration (hh:mm) 08:00 Corresponding NOS Code FFS/N4102

Explain measuring, marking and cutting methods of round bamboo

Demonstrate the correct technique of marking round bamboo

Demonstrate the correct method of cutting round bamboo into required pieces

6 Making round bamboo furniture Theory Duration (hh:mm) 04:00 Practical Duration (hh:mm) 08:00 Corresponding NOS Code FFS/N4102

Explain about the components of round bamboo furniture

Demonstrate the way of making different furniture components from round bamboo culms

Explain joining and lashing techniques

Demonstrate the steps of making different joints

Demonstrate the method of assembling furniture components using joints

Dado, chisel set, dropping knife, hammer, round planer/knot remover, scrapper, blow torch, vice, angle grinder, hand plane, V-shaped knife, pointed knife, mallet, wood saw, hacksaw, pliers, hand drill and bits, sand container, pencil, marker, staple gun, power saw, power drill, hand cutting machine, hand splicer, surface planer, trowel, tumbler, bamboo cross cutting machine, hand


held bamboo splitter, hot air gun, edge trimmer machine, hand engraver machine, stand drill machine, stand zig saw, chalk liner, bamboo of required diameter, adhesive, sand paper, nails, cane (3-4mm for binding), wood pegs, bending wire

7 Finishing Theory Duration (hh:mm) 04:00 Practical Duration (hh:mm) 08:00 Corresponding NOS Code FFS/N4102

Explain the sanding method of bamboo furniture

Explain the method of filling cracks or unwanted cavities

Demonstrate sanding of the surface for smoothness

Demonstrate the method of filling cracks and unwanted cavities

Buffing wheel, hand buff, wax polish clothe, sand paper, oil pad, lacquer spray gun, paint brush, roller coating

8 Working Safely Theory Duration (hh:mm) 04:00 Practical Duration (hh:mm) 08:00 Corresponding NOS Code FFS/N4102

Explain the importance of health and safety legislation/ regulations/ other relevant guidelines

Demonstrate the ways of handling and using tools and equipment safely

Gloves, safety shoes, safety cap/helmet, earplugs, goggles, nose mask, first aid box, fire extinguisher

Option 1: Total Duration Theory Duration: 28 hours Practical Duration: 56 hours

Grand Total Duration Minimum duration for the QP= 260 hrs Theory: 80 hrs Practical: 180 hrs

Unique equipment required for the QP: Gloves, earplugs, goggles, nose mask, safety shoes, safety cap/helmet, safety cap/helmet, first aid box, fire extinguisher Dado, chisel set, dropping knife, hammer, round planer/knot remover, scrapper, blow torch, vice, angle grinder, hand plane, V-shaped knife,


Maximum duration for the QP= 344 hrs Theory: 108 hrs Practical: 236 hrs

pointed knife, mallet, wood saw, hacksaw, pliers, hand drill and bits, sand container, staple gun Power saw, power drill, hand cutting machine, hand splicer, surface planer, trowel, tumbler Bamboo of required diameter, slats, adhesive, sand paper, nails, cane (3-4mm for binding), wood pegs, bending wire Bamboo cross cutting machine, hand held bamboo splitter, hot air gun, edge trimmer machine, hand engraver machine, stand drill machine, stand zig saw, chalk liner, buffing wheel, hand buff, sand paper, wax polish clothe, oil pad, lacquer spray gun, paint brush, roller coating Classroom aids: Blackboard, chalks, duster

(This syllabus/ curriculum has been approved by Furniture & Fittings Skill Council)


Trainer Prerequisites for Job role: “Lead Furniture Maker- Bamboo (Option: Round Bamboo)” mapped to Qualification Pack: “FFS/Q4102, V2.0”

Sr. No.

Area Details

1 Description To deliver accredited training service, mapping to the curriculum detailed above, in accordance with the Qualification Pack “FFS/Q4102, V2.0”.

2 Personal Attributes

Aptitude for conducting training, and pre/ post work to ensure competent, employable candidates at the end of the training. Strong communication skills, interpersonal skills, ability to work as part of a team; a passion for quality and for developing others; well organized and focused, eager to learn and keep oneself updated with the latest in the mentioned field

3 Minimum Educational Qualifications

Minimum 10th pass

Minimum age 25 years

4a Domain Certification

Certified for Job Role: “Lead Furniture Maker- Bamboo (Option: Round Bamboo)” mapped to QP: “FFS/Q4102,V2.0”. Minimum accepted score 80% as per the FFSC guideline.

4b Platform Certification

Recommended that the Trainer is certified for the Job Role: “Trainer”, mapped to the Qualification Pack: “MEP/Q2601”. Minimum accepted score as per respective FFSC guideline is 80%.

5 Experience Minimum five years of experience in furniture making especially in bamboo furniture making


Annexure: Assessment Criteria

Please refer to the QP PDF for the Assessment Criteria.

Documents

Model Curriculum - National Skill Development Corporation · 2 Lead Furniture Maker- Bamboo (Option: Round Bamboo) This course encompasses 5 out of 5 Compulsory NOS (National Occupational